arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts

   1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
   2 /*
   3  * Copyright (C) 2018 SolidRun ltd.
   4  * Based on Marvell MACCHIATOBin board
   5  *
   6  * Device Tree file for SolidRun's ClearFog GT 8K
   7  */
   8
   9 #include "armada-8040.dtsi"
  10
  11 #include <dt-bindings/input/input.h>
  12 #include <dt-bindings/gpio/gpio.h>
  13
  14 / {
  15         model = "SolidRun ClearFog GT 8K";
  16         compatible = "solidrun,clearfog-gt-8k", "marvell,armada8040",
  17                         "marvell,armada-ap806-quad", "marvell,armada-ap806";
  18
  19         chosen {
  20                 stdout-path = "serial0:115200n8";
  21         };
  22
  23         memory@00000000 {
  24                 device_type = "memory";
  25                 reg = <0x0 0x0 0x0 0x80000000>;
  26         };
  27
  28         aliases {
  29                 ethernet0 = &cp1_eth1;
  30                 ethernet1 = &cp0_eth0;
  31                 ethernet2 = &cp1_eth2;
  32         };
  33
  34         v_3_3: regulator-3-3v {
  35                 compatible = "regulator-fixed";
  36                 regulator-name = "v_3_3";
  37                 regulator-min-microvolt = <3300000>;
  38                 regulator-max-microvolt = <3300000>;
  39                 regulator-always-on;
  40                 status = "okay";
  41         };
  42
  43         v_5v0_usb3_hst_vbus: regulator-usb3-vbus0 {
  44                 compatible = "regulator-fixed";
  45                 gpio = <&cp0_gpio2 15 GPIO_ACTIVE_LOW>;
  46                 pinctrl-names = "default";
  47                 pinctrl-0 = <&cp0_xhci_vbus_pins>;
  48                 regulator-name = "v_5v0_usb3_hst_vbus";
  49                 regulator-min-microvolt = <5000000>;
  50                 regulator-max-microvolt = <5000000>;
  51                 status = "okay";
  52         };
  53
  54         sfp_cp0_eth0: sfp-cp0-eth0 {
  55                 compatible = "sff,sfp";
  56                 i2c-bus = <&cp0_i2c1>;
  57                 mod-def0-gpio = <&cp0_gpio2 17 GPIO_ACTIVE_LOW>;
  58                 tx-disable-gpio = <&cp1_gpio1 29 GPIO_ACTIVE_HIGH>;
  59                 pinctrl-names = "default";
  60                 pinctrl-0 = <&cp0_sfp_present_pins &cp1_sfp_tx_disable_pins>;
  61                 maximum-power-milliwatt = <2000>;
  62         };
  63
  64         leds {
  65                 compatible = "gpio-leds";
  66                 pinctrl-0 = <&cp0_led0_pins
  67                              &cp0_led1_pins>;
  68                 pinctrl-names = "default";
  69                 /* No designated function for these LEDs at the moment */
  70                 led0 {
  71                         label = "clearfog-gt-8k:green:led0";
  72                         gpios = <&cp0_gpio2 8 GPIO_ACTIVE_LOW>;
  73                         default-state = "on";
  74                 };
  75                 led1 {
  76                         label = "clearfog-gt-8k:green:led1";
  77                         gpios = <&cp0_gpio2 9 GPIO_ACTIVE_LOW>;
  78                         default-state = "on";
  79                 };
  80         };
  81
  82         keys {
  83                 compatible = "gpio-keys";
  84                 pinctrl-0 = <&cp0_gpio_reset_pins &cp1_wps_button_pins>;
  85                 pinctrl-names = "default";
  86
  87                 button_0 {
  88                         /* The rear button */
  89                         label = "Rear Button";
  90                         gpios = <&cp0_gpio2 7 GPIO_ACTIVE_LOW>;
  91                         linux,can-disable;
  92                         linux,code = <BTN_0>;
  93                 };
  94
  95                 button_1 {
  96                         /* The wps button */
  97                         label = "WPS Button";
  98                         gpios = <&cp1_gpio1 30 GPIO_ACTIVE_LOW>;
  99                         linux,can-disable;
 100                         linux,code = <KEY_WPS_BUTTON>;
 101                 };
 102         };
 103 };
 104
 105 &uart0 {
 106         status = "okay";
 107         pinctrl-0 = <&uart0_pins>;
 108         pinctrl-names = "default";
 109 };
 110
 111 &ap_sdhci0 {
 112         bus-width = <8>;
 113         no-1-8-v;
 114         no-sd;
 115         no-sdio;
 116         non-removable;
 117         status = "okay";
 118         vqmmc-supply = <&v_3_3>;
 119 };
 120
 121 &cp0_i2c0 {
 122         clock-frequency = <100000>;
 123         pinctrl-names = "default";
 124         pinctrl-0 = <&cp0_i2c0_pins>;
 125         status = "okay";
 126 };
 127
 128 &cp0_i2c1 {
 129         clock-frequency = <100000>;
 130         pinctrl-names = "default";
 131         pinctrl-0 = <&cp0_i2c1_pins>;
 132         status = "okay";
 133 };
 134
 135 &cp0_pinctrl {
 136         /*
 137          * MPP Bus:
 138          * [0-31] = 0xff: Keep default CP0_shared_pins:
 139          * [11] CLKOUT_MPP_11 (out)
 140          * [23] LINK_RD_IN_CP2CP (in)
 141          * [25] CLKOUT_MPP_25 (out)
 142          * [29] AVS_FB_IN_CP2CP (in)
 143          * [32, 33, 34] pci0/1/2 reset
 144          * [35-38] CP0 I2C1 and I2C0
 145          * [39] GPIO reset button
 146          * [40,41] LED0 and LED1
 147          * [43] 1512 phy reset
 148          * [47] USB VBUS EN (active low)
 149          * [48] FAN PWM
 150          * [49] SFP+ present signal
 151          * [50] TPM interrupt
 152          * [51] WLAN0 disable
 153          * [52] WLAN1 disable
 154          * [53] LTE disable
 155          * [54] NFC reset
 156          * [55] Micro SD card detect
 157          * [56-61] Micro SD
 158          */
 159
 160         cp0_pci0_reset_pins: pci0-reset-pins {
 161                 marvell,pins = "mpp32";
 162                 marvell,function = "gpio";
 163         };
 164
 165         cp0_pci1_reset_pins: pci1-reset-pins {
 166                 marvell,pins = "mpp33";
 167                 marvell,function = "gpio";
 168         };
 169
 170         cp0_pci2_reset_pins: pci2-reset-pins {
 171                 marvell,pins = "mpp34";
 172                 marvell,function = "gpio";
 173         };
 174
 175         cp0_i2c1_pins: i2c1-pins {
 176                 marvell,pins = "mpp35", "mpp36";
 177                 marvell,function = "i2c1";
 178         };
 179
 180         cp0_i2c0_pins: i2c0-pins {
 181                 marvell,pins = "mpp37", "mpp38";
 182                 marvell,function = "i2c0";
 183         };
 184
 185         cp0_gpio_reset_pins: gpio-reset-pins {
 186                 marvell,pins = "mpp39";
 187                 marvell,function = "gpio";
 188         };
 189
 190         cp0_led0_pins: led0-pins {
 191                 marvell,pins = "mpp40";
 192                 marvell,function = "gpio";
 193         };
 194
 195         cp0_led1_pins: led1-pins {
 196                 marvell,pins = "mpp41";
 197                 marvell,function = "gpio";
 198         };
 199
 200         cp0_copper_eth_phy_reset: copper-eth-phy-reset {
 201                 marvell,pins = "mpp43";
 202                 marvell,function = "gpio";
 203         };
 204
 205         cp0_xhci_vbus_pins: xhci0-vbus-pins {
 206                 marvell,pins = "mpp47";
 207                 marvell,function = "gpio";
 208         };
 209
 210         cp0_fan_pwm_pins: fan-pwm-pins {
 211                 marvell,pins = "mpp48";
 212                 marvell,function = "gpio";
 213         };
 214
 215         cp0_sfp_present_pins: sfp-present-pins {
 216                 marvell,pins = "mpp49";
 217                 marvell,function = "gpio";
 218         };
 219
 220         cp0_tpm_irq_pins: tpm-irq-pins {
 221                 marvell,pins = "mpp50";
 222                 marvell,function = "gpio";
 223         };
 224
 225         cp0_wlan_disable_pins: wlan-disable-pins {
 226                 marvell,pins = "mpp51";
 227                 marvell,function = "gpio";
 228         };
 229
 230         cp0_sdhci_pins: sdhci-pins {
 231                 marvell,pins = "mpp55", "mpp56", "mpp57", "mpp58", "mpp59",
 232                                "mpp60", "mpp61";
 233                 marvell,function = "sdio";
 234         };
 235 };
 236
 237 &cp0_pcie0 {
 238         pinctrl-names = "default";
 239         pinctrl-0 = <&cp0_pci0_reset_pins &cp0_wlan_disable_pins>;
 240         reset-gpios = <&cp0_gpio2 0 GPIO_ACTIVE_LOW>;
 241         phys = <&cp0_comphy0 0>;
 242         phy-names = "cp0-pcie0-x1-phy";
 243         status = "okay";
 244 };
 245
 246 &cp0_gpio2 {
 247         sata_reset {
 248                 gpio-hog;
 249                 gpios = <1 GPIO_ACTIVE_HIGH>;
 250                 output-high;
 251         };
 252
 253         lte_reset {
 254                 gpio-hog;
 255                 gpios = <2 GPIO_ACTIVE_LOW>;
 256                 output-low;
 257         };
 258
 259         wlan_disable {
 260                 gpio-hog;
 261                 gpios = <19 GPIO_ACTIVE_LOW>;
 262                 output-low;
 263         };
 264
 265         lte_disable {
 266                 gpio-hog;
 267                 gpios = <21 GPIO_ACTIVE_LOW>;
 268                 output-low;
 269         };
 270 };
 271
 272 &cp0_ethernet {
 273         status = "okay";
 274 };
 275
 276 /* SFP */
 277 &cp0_eth0 {
 278         status = "okay";
 279         phy-mode = "10gbase-kr";
 280         managed = "in-band-status";
 281         phys = <&cp0_comphy2 0>;
 282         sfp = <&sfp_cp0_eth0>;
 283 };
 284
 285 &cp0_sdhci0 {
 286         broken-cd;
 287         bus-width = <4>;
 288         pinctrl-names = "default";
 289         pinctrl-0 = <&cp0_sdhci_pins>;
 290         status = "okay";
 291         vqmmc-supply = <&v_3_3>;
 292 };
 293
 294 &cp0_usb3_1 {
 295         status = "okay";
 296 };
 297
 298 &cp1_pinctrl {
 299         /*
 300          * MPP Bus:
 301          * [0-5] TDM
 302          * [6]   VHV Enable
 303          * [7]   CP1 SPI0 CSn1 (FXS)
 304          * [8]   CP1 SPI0 CSn0 (TPM)
 305          * [9.11]CP1 SPI0 MOSI/MISO/CLK
 306          * [13]  CP1 SPI1 MISO (TDM and SPI ROM shared)
 307          * [14]  CP1 SPI1 CS0n (64Mb SPI ROM)
 308          * [15]  CP1 SPI1 MOSI (TDM and SPI ROM shared)
 309          * [16]  CP1 SPI1 CLK (TDM and SPI ROM shared)
 310          * [24]  Topaz switch reset
 311          * [26]  Buzzer
 312          * [27]  CP1 SMI MDIO
 313          * [28]  CP1 SMI MDC
 314          * [29]  CP0 10G SFP TX Disable
 315          * [30]  WPS button
 316          * [31]  Front panel button
 317          */
 318
 319         cp1_spi1_pins: spi1-pins {
 320                 marvell,pins = "mpp13", "mpp14", "mpp15", "mpp16";
 321                 marvell,function = "spi1";
 322         };
 323
 324         cp1_switch_reset_pins: switch-reset-pins {
 325                 marvell,pins = "mpp24";
 326                 marvell,function = "gpio";
 327         };
 328
 329         cp1_ge_mdio_pins: ge-mdio-pins {
 330                 marvell,pins = "mpp27", "mpp28";
 331                 marvell,function = "ge";
 332         };
 333
 334         cp1_sfp_tx_disable_pins: sfp-tx-disable-pins {
 335                 marvell,pins = "mpp29";
 336                 marvell,function = "gpio";
 337         };
 338
 339         cp1_wps_button_pins: wps-button-pins {
 340                 marvell,pins = "mpp30";
 341                 marvell,function = "gpio";
 342         };
 343 };
 344
 345 &cp1_sata0 {
 346         pinctrl-0 = <&cp0_pci1_reset_pins>;
 347         status = "okay";
 348
 349         sata-port@1 {
 350                 phys = <&cp1_comphy0 1>;
 351                 phy-names = "cp1-sata0-1-phy";
 352         };
 353 };
 354
 355 &cp1_mdio {
 356         pinctrl-names = "default";
 357         pinctrl-0 = <&cp1_ge_mdio_pins>;
 358         status = "okay";
 359
 360         ge_phy: ethernet-phy@0 {
 361                 /* LED0 - GB link
 362                  * LED1 - on: link, blink: activity
 363                  */
 364                 marvell,reg-init = <3 16 0 0x1017>;
 365                 reg = <0>;
 366                 pinctrl-names = "default";
 367                 pinctrl-0 = <&cp0_copper_eth_phy_reset>;
 368                 reset-gpios = <&cp0_gpio2 11 GPIO_ACTIVE_LOW>;
 369                 reset-assert-us = <10000>;
 370         };
 371
 372         switch0: switch0@4 {
 373                 compatible = "marvell,mv88e6085";
 374                 reg = <4>;
 375                 pinctrl-names = "default";
 376                 pinctrl-0 = <&cp1_switch_reset_pins>;
 377                 reset-gpios = <&cp1_gpio1 24 GPIO_ACTIVE_LOW>;
 378
 379                 ports {
 380                         #address-cells = <1>;
 381                         #size-cells = <0>;
 382
 383                         port@1 {
 384                                 reg = <1>;
 385                                 label = "lan2";
 386                                 phy-handle = <&switch0phy0>;
 387                         };
 388
 389                         port@2 {
 390                                 reg = <2>;
 391                                 label = "lan1";
 392                                 phy-handle = <&switch0phy1>;
 393                         };
 394
 395                         port@3 {
 396                                 reg = <3>;
 397                                 label = "lan4";
 398                                 phy-handle = <&switch0phy2>;
 399                         };
 400
 401                         port@4 {
 402                                 reg = <4>;
 403                                 label = "lan3";
 404                                 phy-handle = <&switch0phy3>;
 405                         };
 406
 407                         port@5 {
 408                                 reg = <5>;
 409                                 label = "cpu";
 410                                 ethernet = <&cp1_eth2>;
 411                                 phy-mode = "2500base-x";
 412                                 managed = "in-band-status";
 413                         };
 414                 };
 415
 416                 mdio {
 417                         #address-cells = <1>;
 418                         #size-cells = <0>;
 419
 420                         switch0phy0: switch0phy0@11 {
 421                                 reg = <0x11>;
 422                         };
 423
 424                         switch0phy1: switch0phy1@12 {
 425                                 reg = <0x12>;
 426                         };
 427
 428                         switch0phy2: switch0phy2@13 {
 429                                 reg = <0x13>;
 430                         };
 431
 432                         switch0phy3: switch0phy3@14 {
 433                                 reg = <0x14>;
 434                         };
 435                 };
 436         };
 437 };
 438
 439 &cp1_ethernet {
 440         status = "okay";
 441 };
 442
 443 /* 1G copper */
 444 &cp1_eth1 {
 445         status = "okay";
 446         phy-mode = "sgmii";
 447         phy = <&ge_phy>;
 448         phys = <&cp1_comphy3 1>;
 449 };
 450
 451 /* Switch uplink */
 452 &cp1_eth2 {
 453         status = "okay";
 454         phy-mode = "2500base-x";
 455         phys = <&cp1_comphy5 2>;
 456         fixed-link {
 457                 speed = <2500>;
 458                 full-duplex;
 459         };
 460 };
 461
 462 &cp1_spi1 {
 463         pinctrl-names = "default";
 464         pinctrl-0 = <&cp1_spi1_pins>;
 465         status = "okay";
 466
 467         spi-flash@0 {
 468                 compatible = "st,w25q32";
 469                 spi-max-frequency = <50000000>;
 470                 reg = <0>;
 471         };
 472 };
 473
 474 &cp1_comphy2 {
 475         cp1_usbh0_con: connector {
 476                 compatible = "usb-a-connector";
 477                 phy-supply = <&v_5v0_usb3_hst_vbus>;
 478         };
 479 };
 480
 481 &cp1_usb3_0 {
 482         phys = <&cp1_comphy2 0>;
 483         phy-names = "cp1-usb3h0-comphy";
 484         status = "okay";
 485 };