drivers/mmc/host/sdhci-msm.c

   1 // SPDX-License-Identifier: GPL-2.0-only
   2 /*
   3  * drivers/mmc/host/sdhci-msm.c - Qualcomm SDHCI Platform driver
   4  *
   5  * Copyright (c) 2013-2014, The Linux Foundation. All rights reserved.
   6  */
   7
   8 #include <linux/module.h>
   9 #include <linux/of_device.h>
  10 #include <linux/delay.h>
  11 #include <linux/mmc/mmc.h>
  12 #include <linux/pm_runtime.h>
  13 #include <linux/slab.h>
  14 #include <linux/iopoll.h>
  15 #include <linux/regulator/consumer.h>
  16
  17 #include "sdhci-pltfm.h"
  18 #include "cqhci.h"
  19
  20 #define CORE_MCI_VERSION                0x50
  21 #define CORE_VERSION_MAJOR_SHIFT        28
  22 #define CORE_VERSION_MAJOR_MASK         (0xf << CORE_VERSION_MAJOR_SHIFT)
  23 #define CORE_VERSION_MINOR_MASK         0xff
  24
  25 #define CORE_MCI_GENERICS               0x70
  26 #define SWITCHABLE_SIGNALING_VOLTAGE    BIT(29)
  27
  28 #define HC_MODE_EN              0x1
  29 #define CORE_POWER              0x0
  30 #define CORE_SW_RST             BIT(7)
  31 #define FF_CLK_SW_RST_DIS       BIT(13)
  32
  33 #define CORE_PWRCTL_BUS_OFF     BIT(0)
  34 #define CORE_PWRCTL_BUS_ON      BIT(1)
  35 #define CORE_PWRCTL_IO_LOW      BIT(2)
  36 #define CORE_PWRCTL_IO_HIGH     BIT(3)
  37 #define CORE_PWRCTL_BUS_SUCCESS BIT(0)
  38 #define CORE_PWRCTL_IO_SUCCESS  BIT(2)
  39 #define REQ_BUS_OFF             BIT(0)
  40 #define REQ_BUS_ON              BIT(1)
  41 #define REQ_IO_LOW              BIT(2)
  42 #define REQ_IO_HIGH             BIT(3)
  43 #define INT_MASK                0xf
  44 #define MAX_PHASES              16
  45 #define CORE_DLL_LOCK           BIT(7)
  46 #define CORE_DDR_DLL_LOCK       BIT(11)
  47 #define CORE_DLL_EN             BIT(16)
  48 #define CORE_CDR_EN             BIT(17)
  49 #define CORE_CK_OUT_EN          BIT(18)
  50 #define CORE_CDR_EXT_EN         BIT(19)
  51 #define CORE_DLL_PDN            BIT(29)
  52 #define CORE_DLL_RST            BIT(30)
  53 #define CORE_CMD_DAT_TRACK_SEL  BIT(0)
  54
  55 #define CORE_DDR_CAL_EN         BIT(0)
  56 #define CORE_FLL_CYCLE_CNT      BIT(18)
  57 #define CORE_DLL_CLOCK_DISABLE  BIT(21)
  58
  59 #define CORE_VENDOR_SPEC_POR_VAL 0xa1c
  60 #define CORE_CLK_PWRSAVE        BIT(1)
  61 #define CORE_HC_MCLK_SEL_DFLT   (2 << 8)
  62 #define CORE_HC_MCLK_SEL_HS400  (3 << 8)
  63 #define CORE_HC_MCLK_SEL_MASK   (3 << 8)
  64 #define CORE_IO_PAD_PWR_SWITCH_EN       (1 << 15)
  65 #define CORE_IO_PAD_PWR_SWITCH  (1 << 16)
  66 #define CORE_HC_SELECT_IN_EN    BIT(18)
  67 #define CORE_HC_SELECT_IN_HS400 (6 << 19)
  68 #define CORE_HC_SELECT_IN_MASK  (7 << 19)
  69
  70 #define CORE_3_0V_SUPPORT       (1 << 25)
  71 #define CORE_1_8V_SUPPORT       (1 << 26)
  72 #define CORE_VOLT_SUPPORT       (CORE_3_0V_SUPPORT | CORE_1_8V_SUPPORT)
  73
  74 #define CORE_CSR_CDC_CTLR_CFG0          0x130
  75 #define CORE_SW_TRIG_FULL_CALIB         BIT(16)
  76 #define CORE_HW_AUTOCAL_ENA             BIT(17)
  77
  78 #define CORE_CSR_CDC_CTLR_CFG1          0x134
  79 #define CORE_CSR_CDC_CAL_TIMER_CFG0     0x138
  80 #define CORE_TIMER_ENA                  BIT(16)
  81
  82 #define CORE_CSR_CDC_CAL_TIMER_CFG1     0x13C
  83 #define CORE_CSR_CDC_REFCOUNT_CFG       0x140
  84 #define CORE_CSR_CDC_COARSE_CAL_CFG     0x144
  85 #define CORE_CDC_OFFSET_CFG             0x14C
  86 #define CORE_CSR_CDC_DELAY_CFG          0x150
  87 #define CORE_CDC_SLAVE_DDA_CFG          0x160
  88 #define CORE_CSR_CDC_STATUS0            0x164
  89 #define CORE_CALIBRATION_DONE           BIT(0)
  90
  91 #define CORE_CDC_ERROR_CODE_MASK        0x7000000
  92
  93 #define CORE_CSR_CDC_GEN_CFG            0x178
  94 #define CORE_CDC_SWITCH_BYPASS_OFF      BIT(0)
  95 #define CORE_CDC_SWITCH_RC_EN           BIT(1)
  96
  97 #define CORE_CDC_T4_DLY_SEL             BIT(0)
  98 #define CORE_CMDIN_RCLK_EN              BIT(1)
  99 #define CORE_START_CDC_TRAFFIC          BIT(6)
 100
 101 #define CORE_PWRSAVE_DLL        BIT(3)
 102
 103 #define DDR_CONFIG_POR_VAL      0x80040873
 104
 105
 106 #define INVALID_TUNING_PHASE    -1
 107 #define SDHCI_MSM_MIN_CLOCK     400000
 108 #define CORE_FREQ_100MHZ        (100 * 1000 * 1000)
 109
 110 #define CDR_SELEXT_SHIFT        20
 111 #define CDR_SELEXT_MASK         (0xf << CDR_SELEXT_SHIFT)
 112 #define CMUX_SHIFT_PHASE_SHIFT  24
 113 #define CMUX_SHIFT_PHASE_MASK   (7 << CMUX_SHIFT_PHASE_SHIFT)
 114
 115 #define MSM_MMC_AUTOSUSPEND_DELAY_MS    50
 116
 117 /* Timeout value to avoid infinite waiting for pwr_irq */
 118 #define MSM_PWR_IRQ_TIMEOUT_MS 5000
 119
 120 #define msm_host_readl(msm_host, host, offset) \
 121         msm_host->var_ops->msm_readl_relaxed(host, offset)
 122
 123 #define msm_host_writel(msm_host, val, host, offset) \
 124         msm_host->var_ops->msm_writel_relaxed(val, host, offset)
 125
 126 /* CQHCI vendor specific registers */
 127 #define CQHCI_VENDOR_CFG1       0xA00
 128 #define CQHCI_VENDOR_DIS_RST_ON_CQ_EN   (0x3 << 13)
 129
 130 struct sdhci_msm_offset {
 131         u32 core_hc_mode;
 132         u32 core_mci_data_cnt;
 133         u32 core_mci_status;
 134         u32 core_mci_fifo_cnt;
 135         u32 core_mci_version;
 136         u32 core_generics;
 137         u32 core_testbus_config;
 138         u32 core_testbus_sel2_bit;
 139         u32 core_testbus_ena;
 140         u32 core_testbus_sel2;
 141         u32 core_pwrctl_status;
 142         u32 core_pwrctl_mask;
 143         u32 core_pwrctl_clear;
 144         u32 core_pwrctl_ctl;
 145         u32 core_sdcc_debug_reg;
 146         u32 core_dll_config;
 147         u32 core_dll_status;
 148         u32 core_vendor_spec;
 149         u32 core_vendor_spec_adma_err_addr0;
 150         u32 core_vendor_spec_adma_err_addr1;
 151         u32 core_vendor_spec_func2;
 152         u32 core_vendor_spec_capabilities0;
 153         u32 core_ddr_200_cfg;
 154         u32 core_vendor_spec3;
 155         u32 core_dll_config_2;
 156         u32 core_dll_config_3;
 157         u32 core_ddr_config_old; /* Applicable to sdcc minor ver < 0x49 */
 158         u32 core_ddr_config;
 159 };
 160
 161 static const struct sdhci_msm_offset sdhci_msm_v5_offset = {
 162         .core_mci_data_cnt = 0x35c,
 163         .core_mci_status = 0x324,
 164         .core_mci_fifo_cnt = 0x308,
 165         .core_mci_version = 0x318,
 166         .core_generics = 0x320,
 167         .core_testbus_config = 0x32c,
 168         .core_testbus_sel2_bit = 3,
 169         .core_testbus_ena = (1 << 31),
 170         .core_testbus_sel2 = (1 << 3),
 171         .core_pwrctl_status = 0x240,
 172         .core_pwrctl_mask = 0x244,
 173         .core_pwrctl_clear = 0x248,
 174         .core_pwrctl_ctl = 0x24c,
 175         .core_sdcc_debug_reg = 0x358,
 176         .core_dll_config = 0x200,
 177         .core_dll_status = 0x208,
 178         .core_vendor_spec = 0x20c,
 179         .core_vendor_spec_adma_err_addr0 = 0x214,
 180         .core_vendor_spec_adma_err_addr1 = 0x218,
 181         .core_vendor_spec_func2 = 0x210,
 182         .core_vendor_spec_capabilities0 = 0x21c,
 183         .core_ddr_200_cfg = 0x224,
 184         .core_vendor_spec3 = 0x250,
 185         .core_dll_config_2 = 0x254,
 186         .core_dll_config_3 = 0x258,
 187         .core_ddr_config = 0x25c,
 188 };
 189
 190 static const struct sdhci_msm_offset sdhci_msm_mci_offset = {
 191         .core_hc_mode = 0x78,
 192         .core_mci_data_cnt = 0x30,
 193         .core_mci_status = 0x34,
 194         .core_mci_fifo_cnt = 0x44,
 195         .core_mci_version = 0x050,
 196         .core_generics = 0x70,
 197         .core_testbus_config = 0x0cc,
 198         .core_testbus_sel2_bit = 4,
 199         .core_testbus_ena = (1 << 3),
 200         .core_testbus_sel2 = (1 << 4),
 201         .core_pwrctl_status = 0xdc,
 202         .core_pwrctl_mask = 0xe0,
 203         .core_pwrctl_clear = 0xe4,
 204         .core_pwrctl_ctl = 0xe8,
 205         .core_sdcc_debug_reg = 0x124,
 206         .core_dll_config = 0x100,
 207         .core_dll_status = 0x108,
 208         .core_vendor_spec = 0x10c,
 209         .core_vendor_spec_adma_err_addr0 = 0x114,
 210         .core_vendor_spec_adma_err_addr1 = 0x118,
 211         .core_vendor_spec_func2 = 0x110,
 212         .core_vendor_spec_capabilities0 = 0x11c,
 213         .core_ddr_200_cfg = 0x184,
 214         .core_vendor_spec3 = 0x1b0,
 215         .core_dll_config_2 = 0x1b4,
 216         .core_ddr_config_old = 0x1b8,
 217         .core_ddr_config = 0x1bc,
 218 };
 219
 220 struct sdhci_msm_variant_ops {
 221         u32 (*msm_readl_relaxed)(struct sdhci_host *host, u32 offset);
 222         void (*msm_writel_relaxed)(u32 val, struct sdhci_host *host,
 223                         u32 offset);
 224 };
 225
 226 /*
 227  * From V5, register spaces have changed. Wrap this info in a structure
 228  * and choose the data_structure based on version info mentioned in DT.
 229  */
 230 struct sdhci_msm_variant_info {
 231         bool mci_removed;
 232         bool restore_dll_config;
 233         const struct sdhci_msm_variant_ops *var_ops;
 234         const struct sdhci_msm_offset *offset;
 235 };
 236
 237 struct sdhci_msm_host {
 238         struct platform_device *pdev;
 239         void __iomem *core_mem; /* MSM SDCC mapped address */
 240         int pwr_irq;            /* power irq */
 241         struct clk *bus_clk;    /* SDHC bus voter clock */
 242         struct clk *xo_clk;     /* TCXO clk needed for FLL feature of cm_dll*/
 243         struct clk_bulk_data bulk_clks[4]; /* core, iface, cal, sleep clocks */
 244         unsigned long clk_rate;
 245         struct mmc_host *mmc;
 246         bool use_14lpp_dll_reset;
 247         bool tuning_done;
 248         bool calibration_done;
 249         u8 saved_tuning_phase;
 250         bool use_cdclp533;
 251         u32 curr_pwr_state;
 252         u32 curr_io_level;
 253         wait_queue_head_t pwr_irq_wait;
 254         bool pwr_irq_flag;
 255         u32 caps_0;
 256         bool mci_removed;
 257         bool restore_dll_config;
 258         const struct sdhci_msm_variant_ops *var_ops;
 259         const struct sdhci_msm_offset *offset;
 260         bool use_cdr;
 261         u32 transfer_mode;
 262         bool updated_ddr_cfg;
 263 };
 264
 265 static const struct sdhci_msm_offset *sdhci_priv_msm_offset(struct sdhci_host *host)
 266 {
 267         struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
 268         struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
 269
 270         return msm_host->offset;
 271 }
 272
 273 /*
 274  * APIs to read/write to vendor specific registers which were there in the
 275  * core_mem region before MCI was removed.
 276  */
 277 static u32 sdhci_msm_mci_variant_readl_relaxed(struct sdhci_host *host,
 278                 u32 offset)
 279 {
 280         struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
 281         struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
 282
 283         return readl_relaxed(msm_host->core_mem + offset);
 284 }
 285
 286 static u32 sdhci_msm_v5_variant_readl_relaxed(struct sdhci_host *host,
 287                 u32 offset)
 288 {
 289         return readl_relaxed(host->ioaddr + offset);
 290 }
 291
 292 static void sdhci_msm_mci_variant_writel_relaxed(u32 val,
 293                 struct sdhci_host *host, u32 offset)
 294 {
 295         struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
 296         struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
 297
 298         writel_relaxed(val, msm_host->core_mem + offset);
 299 }
 300
 301 static void sdhci_msm_v5_variant_writel_relaxed(u32 val,
 302                 struct sdhci_host *host, u32 offset)
 303 {
 304         writel_relaxed(val, host->ioaddr + offset);
 305 }
 306
 307 static unsigned int msm_get_clock_rate_for_bus_mode(struct sdhci_host *host,
 308                                                     unsigned int clock)
 309 {
 310         struct mmc_ios ios = host->mmc->ios;
 311         /*
 312          * The SDHC requires internal clock frequency to be double the
 313          * actual clock that will be set for DDR mode. The controller
 314          * uses the faster clock(100/400MHz) for some of its parts and
 315          * send the actual required clock (50/200MHz) to the card.
 316          */
 317         if (ios.timing == MMC_TIMING_UHS_DDR50 ||
 318             ios.timing == MMC_TIMING_MMC_DDR52 ||
 319             ios.timing == MMC_TIMING_MMC_HS400 ||
 320             host->flags & SDHCI_HS400_TUNING)
 321                 clock *= 2;
 322         return clock;
 323 }
 324
 325 static void msm_set_clock_rate_for_bus_mode(struct sdhci_host *host,
 326                                             unsigned int clock)
 327 {
 328         struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
 329         struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
 330         struct mmc_ios curr_ios = host->mmc->ios;
 331         struct clk *core_clk = msm_host->bulk_clks[0].clk;
 332         int rc;
 333
 334         clock = msm_get_clock_rate_for_bus_mode(host, clock);
 335         rc = clk_set_rate(core_clk, clock);
 336         if (rc) {
 337                 pr_err("%s: Failed to set clock at rate %u at timing %d\n",
 338                        mmc_hostname(host->mmc), clock,
 339                        curr_ios.timing);
 340                 return;
 341         }
 342         msm_host->clk_rate = clock;
 343         pr_debug("%s: Setting clock at rate %lu at timing %d\n",
 344                  mmc_hostname(host->mmc), clk_get_rate(core_clk),
 345                  curr_ios.timing);
 346 }
 347
 348 /* Platform specific tuning */
 349 static inline int msm_dll_poll_ck_out_en(struct sdhci_host *host, u8 poll)
 350 {
 351         u32 wait_cnt = 50;
 352         u8 ck_out_en;
 353         struct mmc_host *mmc = host->mmc;
 354         const struct sdhci_msm_offset *msm_offset =
 355                                         sdhci_priv_msm_offset(host);
 356
 357         /* Poll for CK_OUT_EN bit.  max. poll time = 50us */
 358         ck_out_en = !!(readl_relaxed(host->ioaddr +
 359                         msm_offset->core_dll_config) & CORE_CK_OUT_EN);
 360
 361         while (ck_out_en != poll) {
 362                 if (--wait_cnt == 0) {
 363                         dev_err(mmc_dev(mmc), "%s: CK_OUT_EN bit is not %d\n",
 364                                mmc_hostname(mmc), poll);
 365                         return -ETIMEDOUT;
 366                 }
 367                 udelay(1);
 368
 369                 ck_out_en = !!(readl_relaxed(host->ioaddr +
 370                         msm_offset->core_dll_config) & CORE_CK_OUT_EN);
 371         }
 372
 373         return 0;
 374 }
 375
 376 static int msm_config_cm_dll_phase(struct sdhci_host *host, u8 phase)
 377 {
 378         int rc;
 379         static const u8 grey_coded_phase_table[] = {
 380                 0x0, 0x1, 0x3, 0x2, 0x6, 0x7, 0x5, 0x4,
 381                 0xc, 0xd, 0xf, 0xe, 0xa, 0xb, 0x9, 0x8
 382         };
 383         unsigned long flags;
 384         u32 config;
 385         struct mmc_host *mmc = host->mmc;
 386         const struct sdhci_msm_offset *msm_offset =
 387                                         sdhci_priv_msm_offset(host);
 388
 389         if (phase > 0xf)
 390                 return -EINVAL;
 391
 392         spin_lock_irqsave(&host->lock, flags);
 393
 394         config = readl_relaxed(host->ioaddr + msm_offset->core_dll_config);
 395         config &= ~(CORE_CDR_EN | CORE_CK_OUT_EN);
 396         config |= (CORE_CDR_EXT_EN | CORE_DLL_EN);
 397         writel_relaxed(config, host->ioaddr + msm_offset->core_dll_config);
 398
 399         /* Wait until CK_OUT_EN bit of DLL_CONFIG register becomes '0' */
 400         rc = msm_dll_poll_ck_out_en(host, 0);
 401         if (rc)
 402                 goto err_out;
 403
 404         /*
 405          * Write the selected DLL clock output phase (0 ... 15)
 406          * to CDR_SELEXT bit field of DLL_CONFIG register.
 407          */
 408         config = readl_relaxed(host->ioaddr + msm_offset->core_dll_config);
 409         config &= ~CDR_SELEXT_MASK;
 410         config |= grey_coded_phase_table[phase] << CDR_SELEXT_SHIFT;
 411         writel_relaxed(config, host->ioaddr + msm_offset->core_dll_config);
 412
 413         config = readl_relaxed(host->ioaddr + msm_offset->core_dll_config);
 414         config |= CORE_CK_OUT_EN;
 415         writel_relaxed(config, host->ioaddr + msm_offset->core_dll_config);
 416
 417         /* Wait until CK_OUT_EN bit of DLL_CONFIG register becomes '1' */
 418         rc = msm_dll_poll_ck_out_en(host, 1);
 419         if (rc)
 420                 goto err_out;
 421
 422         config = readl_relaxed(host->ioaddr + msm_offset->core_dll_config);
 423         config |= CORE_CDR_EN;
 424         config &= ~CORE_CDR_EXT_EN;
 425         writel_relaxed(config, host->ioaddr + msm_offset->core_dll_config);
 426         goto out;
 427
 428 err_out:
 429         dev_err(mmc_dev(mmc), "%s: Failed to set DLL phase: %d\n",
 430                mmc_hostname(mmc), phase);
 431 out:
 432         spin_unlock_irqrestore(&host->lock, flags);
 433         return rc;
 434 }
 435
 436 /*
 437  * Find out the greatest range of consecuitive selected
 438  * DLL clock output phases that can be used as sampling
 439  * setting for SD3.0 UHS-I card read operation (in SDR104
 440  * timing mode) or for eMMC4.5 card read operation (in
 441  * HS400/HS200 timing mode).
 442  * Select the 3/4 of the range and configure the DLL with the
 443  * selected DLL clock output phase.
 444  */
 445
 446 static int msm_find_most_appropriate_phase(struct sdhci_host *host,
 447                                            u8 *phase_table, u8 total_phases)
 448 {
 449         int ret;
 450         u8 ranges[MAX_PHASES][MAX_PHASES] = { {0}, {0} };
 451         u8 phases_per_row[MAX_PHASES] = { 0 };
 452         int row_index = 0, col_index = 0, selected_row_index = 0, curr_max = 0;
 453         int i, cnt, phase_0_raw_index = 0, phase_15_raw_index = 0;
 454         bool phase_0_found = false, phase_15_found = false;
 455         struct mmc_host *mmc = host->mmc;
 456
 457         if (!total_phases || (total_phases > MAX_PHASES)) {
 458                 dev_err(mmc_dev(mmc), "%s: Invalid argument: total_phases=%d\n",
 459                        mmc_hostname(mmc), total_phases);
 460                 return -EINVAL;
 461         }
 462
 463         for (cnt = 0; cnt < total_phases; cnt++) {
 464                 ranges[row_index][col_index] = phase_table[cnt];
 465                 phases_per_row[row_index] += 1;
 466                 col_index++;
 467
 468                 if ((cnt + 1) == total_phases) {
 469                         continue;
 470                 /* check if next phase in phase_table is consecutive or not */
 471                 } else if ((phase_table[cnt] + 1) != phase_table[cnt + 1]) {
 472                         row_index++;
 473                         col_index = 0;
 474                 }
 475         }
 476
 477         if (row_index >= MAX_PHASES)
 478                 return -EINVAL;
 479
 480         /* Check if phase-0 is present in first valid window? */
 481         if (!ranges[0][0]) {
 482                 phase_0_found = true;
 483                 phase_0_raw_index = 0;
 484                 /* Check if cycle exist between 2 valid windows */
 485                 for (cnt = 1; cnt <= row_index; cnt++) {
 486                         if (phases_per_row[cnt]) {
 487                                 for (i = 0; i < phases_per_row[cnt]; i++) {
 488                                         if (ranges[cnt][i] == 15) {
 489                                                 phase_15_found = true;
 490                                                 phase_15_raw_index = cnt;
 491                                                 break;
 492                                         }
 493                                 }
 494                         }
 495                 }
 496         }
 497
 498         /* If 2 valid windows form cycle then merge them as single window */
 499         if (phase_0_found && phase_15_found) {
 500                 /* number of phases in raw where phase 0 is present */
 501                 u8 phases_0 = phases_per_row[phase_0_raw_index];
 502                 /* number of phases in raw where phase 15 is present */
 503                 u8 phases_15 = phases_per_row[phase_15_raw_index];
 504
 505                 if (phases_0 + phases_15 >= MAX_PHASES)
 506                         /*
 507                          * If there are more than 1 phase windows then total
 508                          * number of phases in both the windows should not be
 509                          * more than or equal to MAX_PHASES.
 510                          */
 511                         return -EINVAL;
 512
 513                 /* Merge 2 cyclic windows */
 514                 i = phases_15;
 515                 for (cnt = 0; cnt < phases_0; cnt++) {
 516                         ranges[phase_15_raw_index][i] =
 517                             ranges[phase_0_raw_index][cnt];
 518                         if (++i >= MAX_PHASES)
 519                                 break;
 520                 }
 521
 522                 phases_per_row[phase_0_raw_index] = 0;
 523                 phases_per_row[phase_15_raw_index] = phases_15 + phases_0;
 524         }
 525
 526         for (cnt = 0; cnt <= row_index; cnt++) {
 527                 if (phases_per_row[cnt] > curr_max) {
 528                         curr_max = phases_per_row[cnt];
 529                         selected_row_index = cnt;
 530                 }
 531         }
 532
 533         i = (curr_max * 3) / 4;
 534         if (i)
 535                 i--;
 536
 537         ret = ranges[selected_row_index][i];
 538
 539         if (ret >= MAX_PHASES) {
 540                 ret = -EINVAL;
 541                 dev_err(mmc_dev(mmc), "%s: Invalid phase selected=%d\n",
 542                        mmc_hostname(mmc), ret);
 543         }
 544
 545         return ret;
 546 }
 547
 548 static inline void msm_cm_dll_set_freq(struct sdhci_host *host)
 549 {
 550         u32 mclk_freq = 0, config;
 551         const struct sdhci_msm_offset *msm_offset =
 552                                         sdhci_priv_msm_offset(host);
 553
 554         /* Program the MCLK value to MCLK_FREQ bit field */
 555         if (host->clock <= 112000000)
 556                 mclk_freq = 0;
 557         else if (host->clock <= 125000000)
 558                 mclk_freq = 1;
 559         else if (host->clock <= 137000000)
 560                 mclk_freq = 2;
 561         else if (host->clock <= 150000000)
 562                 mclk_freq = 3;
 563         else if (host->clock <= 162000000)
 564                 mclk_freq = 4;
 565         else if (host->clock <= 175000000)
 566                 mclk_freq = 5;
 567         else if (host->clock <= 187000000)
 568                 mclk_freq = 6;
 569         else if (host->clock <= 200000000)
 570                 mclk_freq = 7;
 571
 572         config = readl_relaxed(host->ioaddr + msm_offset->core_dll_config);
 573         config &= ~CMUX_SHIFT_PHASE_MASK;
 574         config |= mclk_freq << CMUX_SHIFT_PHASE_SHIFT;
 575         writel_relaxed(config, host->ioaddr + msm_offset->core_dll_config);
 576 }
 577
 578 /* Initialize the DLL (Programmable Delay Line) */
 579 static int msm_init_cm_dll(struct sdhci_host *host)
 580 {
 581         struct mmc_host *mmc = host->mmc;
 582         struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
 583         struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
 584         int wait_cnt = 50;
 585         unsigned long flags, xo_clk = 0;
 586         u32 config;
 587         const struct sdhci_msm_offset *msm_offset =
 588                                         msm_host->offset;
 589
 590         if (msm_host->use_14lpp_dll_reset && !IS_ERR_OR_NULL(msm_host->xo_clk))
 591                 xo_clk = clk_get_rate(msm_host->xo_clk);
 592
 593         spin_lock_irqsave(&host->lock, flags);
 594
 595         /*
 596          * Make sure that clock is always enabled when DLL
 597          * tuning is in progress. Keeping PWRSAVE ON may
 598          * turn off the clock.
 599          */
 600         config = readl_relaxed(host->ioaddr + msm_offset->core_vendor_spec);
 601         config &= ~CORE_CLK_PWRSAVE;
 602         writel_relaxed(config, host->ioaddr + msm_offset->core_vendor_spec);
 603
 604         if (msm_host->use_14lpp_dll_reset) {
 605                 config = readl_relaxed(host->ioaddr +
 606                                 msm_offset->core_dll_config);
 607                 config &= ~CORE_CK_OUT_EN;
 608                 writel_relaxed(config, host->ioaddr +
 609                                 msm_offset->core_dll_config);
 610
 611                 config = readl_relaxed(host->ioaddr +
 612                                 msm_offset->core_dll_config_2);
 613                 config |= CORE_DLL_CLOCK_DISABLE;
 614                 writel_relaxed(config, host->ioaddr +
 615                                 msm_offset->core_dll_config_2);
 616         }
 617
 618         config = readl_relaxed(host->ioaddr +
 619                         msm_offset->core_dll_config);
 620         config |= CORE_DLL_RST;
 621         writel_relaxed(config, host->ioaddr +
 622                         msm_offset->core_dll_config);
 623
 624         config = readl_relaxed(host->ioaddr +
 625                         msm_offset->core_dll_config);
 626         config |= CORE_DLL_PDN;
 627         writel_relaxed(config, host->ioaddr +
 628                         msm_offset->core_dll_config);
 629         msm_cm_dll_set_freq(host);
 630
 631         if (msm_host->use_14lpp_dll_reset &&
 632             !IS_ERR_OR_NULL(msm_host->xo_clk)) {
 633                 u32 mclk_freq = 0;
 634
 635                 config = readl_relaxed(host->ioaddr +
 636                                 msm_offset->core_dll_config_2);
 637                 config &= CORE_FLL_CYCLE_CNT;
 638                 if (config)
 639                         mclk_freq = DIV_ROUND_CLOSEST_ULL((host->clock * 8),
 640                                         xo_clk);
 641                 else
 642                         mclk_freq = DIV_ROUND_CLOSEST_ULL((host->clock * 4),
 643                                         xo_clk);
 644
 645                 config = readl_relaxed(host->ioaddr +
 646                                 msm_offset->core_dll_config_2);
 647                 config &= ~(0xFF << 10);
 648                 config |= mclk_freq << 10;
 649
 650                 writel_relaxed(config, host->ioaddr +
 651                                 msm_offset->core_dll_config_2);
 652                 /* wait for 5us before enabling DLL clock */
 653                 udelay(5);
 654         }
 655
 656         config = readl_relaxed(host->ioaddr +
 657                         msm_offset->core_dll_config);
 658         config &= ~CORE_DLL_RST;
 659         writel_relaxed(config, host->ioaddr +
 660                         msm_offset->core_dll_config);
 661
 662         config = readl_relaxed(host->ioaddr +
 663                         msm_offset->core_dll_config);
 664         config &= ~CORE_DLL_PDN;
 665         writel_relaxed(config, host->ioaddr +
 666                         msm_offset->core_dll_config);
 667
 668         if (msm_host->use_14lpp_dll_reset) {
 669                 msm_cm_dll_set_freq(host);
 670                 config = readl_relaxed(host->ioaddr +
 671                                 msm_offset->core_dll_config_2);
 672                 config &= ~CORE_DLL_CLOCK_DISABLE;
 673                 writel_relaxed(config, host->ioaddr +
 674                                 msm_offset->core_dll_config_2);
 675         }
 676
 677         config = readl_relaxed(host->ioaddr +
 678                         msm_offset->core_dll_config);
 679         config |= CORE_DLL_EN;
 680         writel_relaxed(config, host->ioaddr +
 681                         msm_offset->core_dll_config);
 682
 683         config = readl_relaxed(host->ioaddr +
 684                         msm_offset->core_dll_config);
 685         config |= CORE_CK_OUT_EN;
 686         writel_relaxed(config, host->ioaddr +
 687                         msm_offset->core_dll_config);
 688
 689         /* Wait until DLL_LOCK bit of DLL_STATUS register becomes '1' */
 690         while (!(readl_relaxed(host->ioaddr + msm_offset->core_dll_status) &
 691                  CORE_DLL_LOCK)) {
 692                 /* max. wait for 50us sec for LOCK bit to be set */
 693                 if (--wait_cnt == 0) {
 694                         dev_err(mmc_dev(mmc), "%s: DLL failed to LOCK\n",
 695                                mmc_hostname(mmc));
 696                         spin_unlock_irqrestore(&host->lock, flags);
 697                         return -ETIMEDOUT;
 698                 }
 699                 udelay(1);
 700         }
 701
 702         spin_unlock_irqrestore(&host->lock, flags);
 703         return 0;
 704 }
 705
 706 static void msm_hc_select_default(struct sdhci_host *host)
 707 {
 708         struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
 709         struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
 710         u32 config;
 711         const struct sdhci_msm_offset *msm_offset =
 712                                         msm_host->offset;
 713
 714         if (!msm_host->use_cdclp533) {
 715                 config = readl_relaxed(host->ioaddr +
 716                                 msm_offset->core_vendor_spec3);
 717                 config &= ~CORE_PWRSAVE_DLL;
 718                 writel_relaxed(config, host->ioaddr +
 719                                 msm_offset->core_vendor_spec3);
 720         }
 721
 722         config = readl_relaxed(host->ioaddr + msm_offset->core_vendor_spec);
 723         config &= ~CORE_HC_MCLK_SEL_MASK;
 724         config |= CORE_HC_MCLK_SEL_DFLT;
 725         writel_relaxed(config, host->ioaddr + msm_offset->core_vendor_spec);
 726
 727         /*
 728          * Disable HC_SELECT_IN to be able to use the UHS mode select
 729          * configuration from Host Control2 register for all other
 730          * modes.
 731          * Write 0 to HC_SELECT_IN and HC_SELECT_IN_EN field
 732          * in VENDOR_SPEC_FUNC
 733          */
 734         config = readl_relaxed(host->ioaddr + msm_offset->core_vendor_spec);
 735         config &= ~CORE_HC_SELECT_IN_EN;
 736         config &= ~CORE_HC_SELECT_IN_MASK;
 737         writel_relaxed(config, host->ioaddr + msm_offset->core_vendor_spec);
 738
 739         /*
 740          * Make sure above writes impacting free running MCLK are completed
 741          * before changing the clk_rate at GCC.
 742          */
 743         wmb();
 744 }
 745
 746 static void msm_hc_select_hs400(struct sdhci_host *host)
 747 {
 748         struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
 749         struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
 750         struct mmc_ios ios = host->mmc->ios;
 751         u32 config, dll_lock;
 752         int rc;
 753         const struct sdhci_msm_offset *msm_offset =
 754                                         msm_host->offset;
 755
 756         /* Select the divided clock (free running MCLK/2) */
 757         config = readl_relaxed(host->ioaddr + msm_offset->core_vendor_spec);
 758         config &= ~CORE_HC_MCLK_SEL_MASK;
 759         config |= CORE_HC_MCLK_SEL_HS400;
 760
 761         writel_relaxed(config, host->ioaddr + msm_offset->core_vendor_spec);
 762         /*
 763          * Select HS400 mode using the HC_SELECT_IN from VENDOR SPEC
 764          * register
 765          */
 766         if ((msm_host->tuning_done || ios.enhanced_strobe) &&
 767             !msm_host->calibration_done) {
 768                 config = readl_relaxed(host->ioaddr +
 769                                 msm_offset->core_vendor_spec);
 770                 config |= CORE_HC_SELECT_IN_HS400;
 771                 config |= CORE_HC_SELECT_IN_EN;
 772                 writel_relaxed(config, host->ioaddr +
 773                                 msm_offset->core_vendor_spec);
 774         }
 775         if (!msm_host->clk_rate && !msm_host->use_cdclp533) {
 776                 /*
 777                  * Poll on DLL_LOCK or DDR_DLL_LOCK bits in
 778                  * core_dll_status to be set. This should get set
 779                  * within 15 us at 200 MHz.
 780                  */
 781                 rc = readl_relaxed_poll_timeout(host->ioaddr +
 782                                                 msm_offset->core_dll_status,
 783                                                 dll_lock,
 784                                                 (dll_lock &
 785                                                 (CORE_DLL_LOCK |
 786                                                 CORE_DDR_DLL_LOCK)), 10,
 787                                                 1000);
 788                 if (rc == -ETIMEDOUT)
 789                         pr_err("%s: Unable to get DLL_LOCK/DDR_DLL_LOCK, dll_status: 0x%08x\n",
 790                                mmc_hostname(host->mmc), dll_lock);
 791         }
 792         /*
 793          * Make sure above writes impacting free running MCLK are completed
 794          * before changing the clk_rate at GCC.
 795          */
 796         wmb();
 797 }
 798
 799 /*
 800  * sdhci_msm_hc_select_mode :- In general all timing modes are
 801  * controlled via UHS mode select in Host Control2 register.
 802  * eMMC specific HS200/HS400 doesn't have their respective modes
 803  * defined here, hence we use these values.
 804  *
 805  * HS200 - SDR104 (Since they both are equivalent in functionality)
 806  * HS400 - This involves multiple configurations
 807  *              Initially SDR104 - when tuning is required as HS200
 808  *              Then when switching to DDR @ 400MHz (HS400) we use
 809  *              the vendor specific HC_SELECT_IN to control the mode.
 810  *
 811  * In addition to controlling the modes we also need to select the
 812  * correct input clock for DLL depending on the mode.
 813  *
 814  * HS400 - divided clock (free running MCLK/2)
 815  * All other modes - default (free running MCLK)
 816  */
 817 static void sdhci_msm_hc_select_mode(struct sdhci_host *host)
 818 {
 819         struct mmc_ios ios = host->mmc->ios;
 820
 821         if (ios.timing == MMC_TIMING_MMC_HS400 ||
 822             host->flags & SDHCI_HS400_TUNING)
 823                 msm_hc_select_hs400(host);
 824         else
 825                 msm_hc_select_default(host);
 826 }
 827
 828 static int sdhci_msm_cdclp533_calibration(struct sdhci_host *host)
 829 {
 830         struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
 831         struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
 832         u32 config, calib_done;
 833         int ret;
 834         const struct sdhci_msm_offset *msm_offset =
 835                                         msm_host->offset;
 836
 837         pr_debug("%s: %s: Enter\n", mmc_hostname(host->mmc), __func__);
 838
 839         /*
 840          * Retuning in HS400 (DDR mode) will fail, just reset the
 841          * tuning block and restore the saved tuning phase.
 842          */
 843         ret = msm_init_cm_dll(host);
 844         if (ret)
 845                 goto out;
 846
 847         /* Set the selected phase in delay line hw block */
 848         ret = msm_config_cm_dll_phase(host, msm_host->saved_tuning_phase);
 849         if (ret)
 850                 goto out;
 851
 852         config = readl_relaxed(host->ioaddr + msm_offset->core_dll_config);
 853         config |= CORE_CMD_DAT_TRACK_SEL;
 854         writel_relaxed(config, host->ioaddr + msm_offset->core_dll_config);
 855
 856         config = readl_relaxed(host->ioaddr + msm_offset->core_ddr_200_cfg);
 857         config &= ~CORE_CDC_T4_DLY_SEL;
 858         writel_relaxed(config, host->ioaddr + msm_offset->core_ddr_200_cfg);
 859
 860         config = readl_relaxed(host->ioaddr + CORE_CSR_CDC_GEN_CFG);
 861         config &= ~CORE_CDC_SWITCH_BYPASS_OFF;
 862         writel_relaxed(config, host->ioaddr + CORE_CSR_CDC_GEN_CFG);
 863
 864         config = readl_relaxed(host->ioaddr + CORE_CSR_CDC_GEN_CFG);
 865         config |= CORE_CDC_SWITCH_RC_EN;
 866         writel_relaxed(config, host->ioaddr + CORE_CSR_CDC_GEN_CFG);
 867
 868         config = readl_relaxed(host->ioaddr + msm_offset->core_ddr_200_cfg);
 869         config &= ~CORE_START_CDC_TRAFFIC;
 870         writel_relaxed(config, host->ioaddr + msm_offset->core_ddr_200_cfg);
 871
 872         /* Perform CDC Register Initialization Sequence */
 873
 874         writel_relaxed(0x11800EC, host->ioaddr + CORE_CSR_CDC_CTLR_CFG0);
 875         writel_relaxed(0x3011111, host->ioaddr + CORE_CSR_CDC_CTLR_CFG1);
 876         writel_relaxed(0x1201000, host->ioaddr + CORE_CSR_CDC_CAL_TIMER_CFG0);
 877         writel_relaxed(0x4, host->ioaddr + CORE_CSR_CDC_CAL_TIMER_CFG1);
 878         writel_relaxed(0xCB732020, host->ioaddr + CORE_CSR_CDC_REFCOUNT_CFG);
 879         writel_relaxed(0xB19, host->ioaddr + CORE_CSR_CDC_COARSE_CAL_CFG);
 880         writel_relaxed(0x4E2, host->ioaddr + CORE_CSR_CDC_DELAY_CFG);
 881         writel_relaxed(0x0, host->ioaddr + CORE_CDC_OFFSET_CFG);
 882         writel_relaxed(0x16334, host->ioaddr + CORE_CDC_SLAVE_DDA_CFG);
 883
 884         /* CDC HW Calibration */
 885
 886         config = readl_relaxed(host->ioaddr + CORE_CSR_CDC_CTLR_CFG0);
 887         config |= CORE_SW_TRIG_FULL_CALIB;
 888         writel_relaxed(config, host->ioaddr + CORE_CSR_CDC_CTLR_CFG0);
 889
 890         config = readl_relaxed(host->ioaddr + CORE_CSR_CDC_CTLR_CFG0);
 891         config &= ~CORE_SW_TRIG_FULL_CALIB;
 892         writel_relaxed(config, host->ioaddr + CORE_CSR_CDC_CTLR_CFG0);
 893
 894         config = readl_relaxed(host->ioaddr + CORE_CSR_CDC_CTLR_CFG0);
 895         config |= CORE_HW_AUTOCAL_ENA;
 896         writel_relaxed(config, host->ioaddr + CORE_CSR_CDC_CTLR_CFG0);
 897
 898         config = readl_relaxed(host->ioaddr + CORE_CSR_CDC_CAL_TIMER_CFG0);
 899         config |= CORE_TIMER_ENA;
 900         writel_relaxed(config, host->ioaddr + CORE_CSR_CDC_CAL_TIMER_CFG0);
 901
 902         ret = readl_relaxed_poll_timeout(host->ioaddr + CORE_CSR_CDC_STATUS0,
 903                                          calib_done,
 904                                          (calib_done & CORE_CALIBRATION_DONE),
 905                                          1, 50);
 906
 907         if (ret == -ETIMEDOUT) {
 908                 pr_err("%s: %s: CDC calibration was not completed\n",
 909                        mmc_hostname(host->mmc), __func__);
 910                 goto out;
 911         }
 912
 913         ret = readl_relaxed(host->ioaddr + CORE_CSR_CDC_STATUS0)
 914                         & CORE_CDC_ERROR_CODE_MASK;
 915         if (ret) {
 916                 pr_err("%s: %s: CDC error code %d\n",
 917                        mmc_hostname(host->mmc), __func__, ret);
 918                 ret = -EINVAL;
 919                 goto out;
 920         }
 921
 922         config = readl_relaxed(host->ioaddr + msm_offset->core_ddr_200_cfg);
 923         config |= CORE_START_CDC_TRAFFIC;
 924         writel_relaxed(config, host->ioaddr + msm_offset->core_ddr_200_cfg);
 925 out:
 926         pr_debug("%s: %s: Exit, ret %d\n", mmc_hostname(host->mmc),
 927                  __func__, ret);
 928         return ret;
 929 }
 930
 931 static int sdhci_msm_cm_dll_sdc4_calibration(struct sdhci_host *host)
 932 {
 933         struct mmc_host *mmc = host->mmc;
 934         u32 dll_status, config, ddr_cfg_offset;
 935         int ret;
 936         struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
 937         struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
 938         const struct sdhci_msm_offset *msm_offset =
 939                                         sdhci_priv_msm_offset(host);
 940
 941         pr_debug("%s: %s: Enter\n", mmc_hostname(host->mmc), __func__);
 942
 943         /*
 944          * Currently the core_ddr_config register defaults to desired
 945          * configuration on reset. Currently reprogramming the power on
 946          * reset (POR) value in case it might have been modified by
 947          * bootloaders. In the future, if this changes, then the desired
 948          * values will need to be programmed appropriately.
 949          */
 950         if (msm_host->updated_ddr_cfg)
 951                 ddr_cfg_offset = msm_offset->core_ddr_config;
 952         else
 953                 ddr_cfg_offset = msm_offset->core_ddr_config_old;
 954         writel_relaxed(DDR_CONFIG_POR_VAL, host->ioaddr + ddr_cfg_offset);
 955
 956         if (mmc->ios.enhanced_strobe) {
 957                 config = readl_relaxed(host->ioaddr +
 958                                 msm_offset->core_ddr_200_cfg);
 959                 config |= CORE_CMDIN_RCLK_EN;
 960                 writel_relaxed(config, host->ioaddr +
 961                                 msm_offset->core_ddr_200_cfg);
 962         }
 963
 964         config = readl_relaxed(host->ioaddr + msm_offset->core_dll_config_2);
 965         config |= CORE_DDR_CAL_EN;
 966         writel_relaxed(config, host->ioaddr + msm_offset->core_dll_config_2);
 967
 968         ret = readl_relaxed_poll_timeout(host->ioaddr +
 969                                         msm_offset->core_dll_status,
 970                                         dll_status,
 971                                         (dll_status & CORE_DDR_DLL_LOCK),
 972                                         10, 1000);
 973
 974         if (ret == -ETIMEDOUT) {
 975                 pr_err("%s: %s: CM_DLL_SDC4 calibration was not completed\n",
 976                        mmc_hostname(host->mmc), __func__);
 977                 goto out;
 978         }
 979
 980         config = readl_relaxed(host->ioaddr + msm_offset->core_vendor_spec3);
 981         config |= CORE_PWRSAVE_DLL;
 982         writel_relaxed(config, host->ioaddr + msm_offset->core_vendor_spec3);
 983
 984         /*
 985          * Drain writebuffer to ensure above DLL calibration
 986          * and PWRSAVE DLL is enabled.
 987          */
 988         wmb();
 989 out:
 990         pr_debug("%s: %s: Exit, ret %d\n", mmc_hostname(host->mmc),
 991                  __func__, ret);
 992         return ret;
 993 }
 994
 995 static int sdhci_msm_hs400_dll_calibration(struct sdhci_host *host)
 996 {
 997         struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
 998         struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
 999         struct mmc_host *mmc = host->mmc;
1000         int ret;
1001         u32 config;
1002         const struct sdhci_msm_offset *msm_offset =
1003                                         msm_host->offset;
1004
1005         pr_debug("%s: %s: Enter\n", mmc_hostname(host->mmc), __func__);
1006
1007         /*
1008          * Retuning in HS400 (DDR mode) will fail, just reset the
1009          * tuning block and restore the saved tuning phase.
1010          */
1011         ret = msm_init_cm_dll(host);
1012         if (ret)
1013                 goto out;
1014
1015         if (!mmc->ios.enhanced_strobe) {
1016                 /* Set the selected phase in delay line hw block */
1017                 ret = msm_config_cm_dll_phase(host,
1018                                               msm_host->saved_tuning_phase);
1019                 if (ret)
1020                         goto out;
1021                 config = readl_relaxed(host->ioaddr +
1022                                 msm_offset->core_dll_config);
1023                 config |= CORE_CMD_DAT_TRACK_SEL;
1024                 writel_relaxed(config, host->ioaddr +
1025                                 msm_offset->core_dll_config);
1026         }
1027
1028         if (msm_host->use_cdclp533)
1029                 ret = sdhci_msm_cdclp533_calibration(host);
1030         else
1031                 ret = sdhci_msm_cm_dll_sdc4_calibration(host);
1032 out:
1033         pr_debug("%s: %s: Exit, ret %d\n", mmc_hostname(host->mmc),
1034                  __func__, ret);
1035         return ret;
1036 }
1037
1038 static bool sdhci_msm_is_tuning_needed(struct sdhci_host *host)
1039 {
1040         struct mmc_ios *ios = &host->mmc->ios;
1041
1042         /*
1043          * Tuning is required for SDR104, HS200 and HS400 cards and
1044          * if clock frequency is greater than 100MHz in these modes.
1045          */
1046         if (host->clock <= CORE_FREQ_100MHZ ||
1047             !(ios->timing == MMC_TIMING_MMC_HS400 ||
1048             ios->timing == MMC_TIMING_MMC_HS200 ||
1049             ios->timing == MMC_TIMING_UHS_SDR104) ||
1050             ios->enhanced_strobe)
1051                 return false;
1052
1053         return true;
1054 }
1055
1056 static int sdhci_msm_restore_sdr_dll_config(struct sdhci_host *host)
1057 {
1058         struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1059         struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
1060         int ret;
1061
1062         /*
1063          * SDR DLL comes into picture only for timing modes which needs
1064          * tuning.
1065          */
1066         if (!sdhci_msm_is_tuning_needed(host))
1067                 return 0;
1068
1069         /* Reset the tuning block */
1070         ret = msm_init_cm_dll(host);
1071         if (ret)
1072                 return ret;
1073
1074         /* Restore the tuning block */
1075         ret = msm_config_cm_dll_phase(host, msm_host->saved_tuning_phase);
1076
1077         return ret;
1078 }
1079
1080 static void sdhci_msm_set_cdr(struct sdhci_host *host, bool enable)
1081 {
1082         const struct sdhci_msm_offset *msm_offset = sdhci_priv_msm_offset(host);
1083         u32 config, oldconfig = readl_relaxed(host->ioaddr +
1084                                               msm_offset->core_dll_config);
1085
1086         config = oldconfig;
1087         if (enable) {
1088                 config |= CORE_CDR_EN;
1089                 config &= ~CORE_CDR_EXT_EN;
1090         } else {
1091                 config &= ~CORE_CDR_EN;
1092                 config |= CORE_CDR_EXT_EN;
1093         }
1094
1095         if (config != oldconfig) {
1096                 writel_relaxed(config, host->ioaddr +
1097                                msm_offset->core_dll_config);
1098         }
1099 }
1100
1101 static int sdhci_msm_execute_tuning(struct mmc_host *mmc, u32 opcode)
1102 {
1103         struct sdhci_host *host = mmc_priv(mmc);
1104         int tuning_seq_cnt = 3;
1105         u8 phase, tuned_phases[16], tuned_phase_cnt = 0;
1106         int rc;
1107         struct mmc_ios ios = host->mmc->ios;
1108         struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1109         struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
1110
1111         if (!sdhci_msm_is_tuning_needed(host)) {
1112                 msm_host->use_cdr = false;
1113                 sdhci_msm_set_cdr(host, false);
1114                 return 0;
1115         }
1116
1117         /* Clock-Data-Recovery used to dynamically adjust RX sampling point */
1118         msm_host->use_cdr = true;
1119
1120         /*
1121          * For HS400 tuning in HS200 timing requires:
1122          * - select MCLK/2 in VENDOR_SPEC
1123          * - program MCLK to 400MHz (or nearest supported) in GCC
1124          */
1125         if (host->flags & SDHCI_HS400_TUNING) {
1126                 sdhci_msm_hc_select_mode(host);
1127                 msm_set_clock_rate_for_bus_mode(host, ios.clock);
1128                 host->flags &= ~SDHCI_HS400_TUNING;
1129         }
1130
1131 retry:
1132         /* First of all reset the tuning block */
1133         rc = msm_init_cm_dll(host);
1134         if (rc)
1135                 return rc;
1136
1137         phase = 0;
1138         do {
1139                 /* Set the phase in delay line hw block */
1140                 rc = msm_config_cm_dll_phase(host, phase);
1141                 if (rc)
1142                         return rc;
1143
1144                 rc = mmc_send_tuning(mmc, opcode, NULL);
1145                 if (!rc) {
1146                         /* Tuning is successful at this tuning point */
1147                         tuned_phases[tuned_phase_cnt++] = phase;
1148                         dev_dbg(mmc_dev(mmc), "%s: Found good phase = %d\n",
1149                                  mmc_hostname(mmc), phase);
1150                 }
1151         } while (++phase < ARRAY_SIZE(tuned_phases));
1152
1153         if (tuned_phase_cnt) {
1154                 rc = msm_find_most_appropriate_phase(host, tuned_phases,
1155                                                      tuned_phase_cnt);
1156                 if (rc < 0)
1157                         return rc;
1158                 else
1159                         phase = rc;
1160
1161                 /*
1162                  * Finally set the selected phase in delay
1163                  * line hw block.
1164                  */
1165                 rc = msm_config_cm_dll_phase(host, phase);
1166                 if (rc)
1167                         return rc;
1168                 msm_host->saved_tuning_phase = phase;
1169                 dev_dbg(mmc_dev(mmc), "%s: Setting the tuning phase to %d\n",
1170                          mmc_hostname(mmc), phase);
1171         } else {
1172                 if (--tuning_seq_cnt)
1173                         goto retry;
1174                 /* Tuning failed */
1175                 dev_dbg(mmc_dev(mmc), "%s: No tuning point found\n",
1176                        mmc_hostname(mmc));
1177                 rc = -EIO;
1178         }
1179
1180         if (!rc)
1181                 msm_host->tuning_done = true;
1182         return rc;
1183 }
1184
1185 /*
1186  * sdhci_msm_hs400 - Calibrate the DLL for HS400 bus speed mode operation.
1187  * This needs to be done for both tuning and enhanced_strobe mode.
1188  * DLL operation is only needed for clock > 100MHz. For clock <= 100MHz
1189  * fixed feedback clock is used.
1190  */
1191 static void sdhci_msm_hs400(struct sdhci_host *host, struct mmc_ios *ios)
1192 {
1193         struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1194         struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
1195         int ret;
1196
1197         if (host->clock > CORE_FREQ_100MHZ &&
1198             (msm_host->tuning_done || ios->enhanced_strobe) &&
1199             !msm_host->calibration_done) {
1200                 ret = sdhci_msm_hs400_dll_calibration(host);
1201                 if (!ret)
1202                         msm_host->calibration_done = true;
1203                 else
1204                         pr_err("%s: Failed to calibrate DLL for hs400 mode (%d)\n",
1205                                mmc_hostname(host->mmc), ret);
1206         }
1207 }
1208
1209 static void sdhci_msm_set_uhs_signaling(struct sdhci_host *host,
1210                                         unsigned int uhs)
1211 {
1212         struct mmc_host *mmc = host->mmc;
1213         struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1214         struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
1215         u16 ctrl_2;
1216         u32 config;
1217         const struct sdhci_msm_offset *msm_offset =
1218                                         msm_host->offset;
1219
1220         ctrl_2 = sdhci_readw(host, SDHCI_HOST_CONTROL2);
1221         /* Select Bus Speed Mode for host */
1222         ctrl_2 &= ~SDHCI_CTRL_UHS_MASK;
1223         switch (uhs) {
1224         case MMC_TIMING_UHS_SDR12:
1225                 ctrl_2 |= SDHCI_CTRL_UHS_SDR12;
1226                 break;
1227         case MMC_TIMING_UHS_SDR25:
1228                 ctrl_2 |= SDHCI_CTRL_UHS_SDR25;
1229                 break;
1230         case MMC_TIMING_UHS_SDR50:
1231                 ctrl_2 |= SDHCI_CTRL_UHS_SDR50;
1232                 break;
1233         case MMC_TIMING_MMC_HS400:
1234         case MMC_TIMING_MMC_HS200:
1235         case MMC_TIMING_UHS_SDR104:
1236                 ctrl_2 |= SDHCI_CTRL_UHS_SDR104;
1237                 break;
1238         case MMC_TIMING_UHS_DDR50:
1239         case MMC_TIMING_MMC_DDR52:
1240                 ctrl_2 |= SDHCI_CTRL_UHS_DDR50;
1241                 break;
1242         }
1243
1244         /*
1245          * When clock frequency is less than 100MHz, the feedback clock must be
1246          * provided and DLL must not be used so that tuning can be skipped. To
1247          * provide feedback clock, the mode selection can be any value less
1248          * than 3'b011 in bits [2:0] of HOST CONTROL2 register.
1249          */
1250         if (host->clock <= CORE_FREQ_100MHZ) {
1251                 if (uhs == MMC_TIMING_MMC_HS400 ||
1252                     uhs == MMC_TIMING_MMC_HS200 ||
1253                     uhs == MMC_TIMING_UHS_SDR104)
1254                         ctrl_2 &= ~SDHCI_CTRL_UHS_MASK;
1255                 /*
1256                  * DLL is not required for clock <= 100MHz
1257                  * Thus, make sure DLL it is disabled when not required
1258                  */
1259                 config = readl_relaxed(host->ioaddr +
1260                                 msm_offset->core_dll_config);
1261                 config |= CORE_DLL_RST;
1262                 writel_relaxed(config, host->ioaddr +
1263                                 msm_offset->core_dll_config);
1264
1265                 config = readl_relaxed(host->ioaddr +
1266                                 msm_offset->core_dll_config);
1267                 config |= CORE_DLL_PDN;
1268                 writel_relaxed(config, host->ioaddr +
1269                                 msm_offset->core_dll_config);
1270
1271                 /*
1272                  * The DLL needs to be restored and CDCLP533 recalibrated
1273                  * when the clock frequency is set back to 400MHz.
1274                  */
1275                 msm_host->calibration_done = false;
1276         }
1277
1278         dev_dbg(mmc_dev(mmc), "%s: clock=%u uhs=%u ctrl_2=0x%x\n",
1279                 mmc_hostname(host->mmc), host->clock, uhs, ctrl_2);
1280         sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2);
1281
1282         if (mmc->ios.timing == MMC_TIMING_MMC_HS400)
1283                 sdhci_msm_hs400(host, &mmc->ios);
1284 }
1285
1286 static inline void sdhci_msm_init_pwr_irq_wait(struct sdhci_msm_host *msm_host)
1287 {
1288         init_waitqueue_head(&msm_host->pwr_irq_wait);
1289 }
1290
1291 static inline void sdhci_msm_complete_pwr_irq_wait(
1292                 struct sdhci_msm_host *msm_host)
1293 {
1294         wake_up(&msm_host->pwr_irq_wait);
1295 }
1296
1297 /*
1298  * sdhci_msm_check_power_status API should be called when registers writes
1299  * which can toggle sdhci IO bus ON/OFF or change IO lines HIGH/LOW happens.
1300  * To what state the register writes will change the IO lines should be passed
1301  * as the argument req_type. This API will check whether the IO line's state
1302  * is already the expected state and will wait for power irq only if
1303  * power irq is expected to be trigerred based on the current IO line state
1304  * and expected IO line state.
1305  */
1306 static void sdhci_msm_check_power_status(struct sdhci_host *host, u32 req_type)
1307 {
1308         struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1309         struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
1310         bool done = false;
1311         u32 val = SWITCHABLE_SIGNALING_VOLTAGE;
1312         const struct sdhci_msm_offset *msm_offset =
1313                                         msm_host->offset;
1314
1315         pr_debug("%s: %s: request %d curr_pwr_state %x curr_io_level %x\n",
1316                         mmc_hostname(host->mmc), __func__, req_type,
1317                         msm_host->curr_pwr_state, msm_host->curr_io_level);
1318
1319         /*
1320          * The power interrupt will not be generated for signal voltage
1321          * switches if SWITCHABLE_SIGNALING_VOLTAGE in MCI_GENERICS is not set.
1322          * Since sdhci-msm-v5, this bit has been removed and SW must consider
1323          * it as always set.
1324          */
1325         if (!msm_host->mci_removed)
1326                 val = msm_host_readl(msm_host, host,
1327                                 msm_offset->core_generics);
1328         if ((req_type & REQ_IO_HIGH || req_type & REQ_IO_LOW) &&
1329             !(val & SWITCHABLE_SIGNALING_VOLTAGE)) {
1330                 return;
1331         }
1332
1333         /*
1334          * The IRQ for request type IO High/LOW will be generated when -
1335          * there is a state change in 1.8V enable bit (bit 3) of
1336          * SDHCI_HOST_CONTROL2 register. The reset state of that bit is 0
1337          * which indicates 3.3V IO voltage. So, when MMC core layer tries
1338          * to set it to 3.3V before card detection happens, the
1339          * IRQ doesn't get triggered as there is no state change in this bit.
1340          * The driver already handles this case by changing the IO voltage
1341          * level to high as part of controller power up sequence. Hence, check
1342          * for host->pwr to handle a case where IO voltage high request is
1343          * issued even before controller power up.
1344          */
1345         if ((req_type & REQ_IO_HIGH) && !host->pwr) {
1346                 pr_debug("%s: do not wait for power IRQ that never comes, req_type: %d\n",
1347                                 mmc_hostname(host->mmc), req_type);
1348                 return;
1349         }
1350         if ((req_type & msm_host->curr_pwr_state) ||
1351                         (req_type & msm_host->curr_io_level))
1352                 done = true;
1353         /*
1354          * This is needed here to handle cases where register writes will
1355          * not change the current bus state or io level of the controller.
1356          * In this case, no power irq will be triggerred and we should
1357          * not wait.
1358          */
1359         if (!done) {
1360                 if (!wait_event_timeout(msm_host->pwr_irq_wait,
1361                                 msm_host->pwr_irq_flag,
1362                                 msecs_to_jiffies(MSM_PWR_IRQ_TIMEOUT_MS)))
1363                         dev_warn(&msm_host->pdev->dev,
1364                                  "%s: pwr_irq for req: (%d) timed out\n",
1365                                  mmc_hostname(host->mmc), req_type);
1366         }
1367         pr_debug("%s: %s: request %d done\n", mmc_hostname(host->mmc),
1368                         __func__, req_type);
1369 }
1370
1371 static void sdhci_msm_dump_pwr_ctrl_regs(struct sdhci_host *host)
1372 {
1373         struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1374         struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
1375         const struct sdhci_msm_offset *msm_offset =
1376                                         msm_host->offset;
1377
1378         pr_err("%s: PWRCTL_STATUS: 0x%08x | PWRCTL_MASK: 0x%08x | PWRCTL_CTL: 0x%08x\n",
1379                 mmc_hostname(host->mmc),
1380                 msm_host_readl(msm_host, host, msm_offset->core_pwrctl_status),
1381                 msm_host_readl(msm_host, host, msm_offset->core_pwrctl_mask),
1382                 msm_host_readl(msm_host, host, msm_offset->core_pwrctl_ctl));
1383 }
1384
1385 static void sdhci_msm_handle_pwr_irq(struct sdhci_host *host, int irq)
1386 {
1387         struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1388         struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
1389         u32 irq_status, irq_ack = 0;
1390         int retry = 10;
1391         u32 pwr_state = 0, io_level = 0;
1392         u32 config;
1393         const struct sdhci_msm_offset *msm_offset = msm_host->offset;
1394
1395         irq_status = msm_host_readl(msm_host, host,
1396                         msm_offset->core_pwrctl_status);
1397         irq_status &= INT_MASK;
1398
1399         msm_host_writel(msm_host, irq_status, host,
1400                         msm_offset->core_pwrctl_clear);
1401
1402         /*
1403          * There is a rare HW scenario where the first clear pulse could be
1404          * lost when actual reset and clear/read of status register is
1405          * happening at a time. Hence, retry for at least 10 times to make
1406          * sure status register is cleared. Otherwise, this will result in
1407          * a spurious power IRQ resulting in system instability.
1408          */
1409         while (irq_status & msm_host_readl(msm_host, host,
1410                                 msm_offset->core_pwrctl_status)) {
1411                 if (retry == 0) {
1412                         pr_err("%s: Timedout clearing (0x%x) pwrctl status register\n",
1413                                         mmc_hostname(host->mmc), irq_status);
1414                         sdhci_msm_dump_pwr_ctrl_regs(host);
1415                         WARN_ON(1);
1416                         break;
1417                 }
1418                 msm_host_writel(msm_host, irq_status, host,
1419                         msm_offset->core_pwrctl_clear);
1420                 retry--;
1421                 udelay(10);
1422         }
1423
1424         /* Handle BUS ON/OFF*/
1425         if (irq_status & CORE_PWRCTL_BUS_ON) {
1426                 pwr_state = REQ_BUS_ON;
1427                 io_level = REQ_IO_HIGH;
1428                 irq_ack |= CORE_PWRCTL_BUS_SUCCESS;
1429         }
1430         if (irq_status & CORE_PWRCTL_BUS_OFF) {
1431                 pwr_state = REQ_BUS_OFF;
1432                 io_level = REQ_IO_LOW;
1433                 irq_ack |= CORE_PWRCTL_BUS_SUCCESS;
1434         }
1435         /* Handle IO LOW/HIGH */
1436         if (irq_status & CORE_PWRCTL_IO_LOW) {
1437                 io_level = REQ_IO_LOW;
1438                 irq_ack |= CORE_PWRCTL_IO_SUCCESS;
1439         }
1440         if (irq_status & CORE_PWRCTL_IO_HIGH) {
1441                 io_level = REQ_IO_HIGH;
1442                 irq_ack |= CORE_PWRCTL_IO_SUCCESS;
1443         }
1444
1445         /*
1446          * The driver has to acknowledge the interrupt, switch voltages and
1447          * report back if it succeded or not to this register. The voltage
1448          * switches are handled by the sdhci core, so just report success.
1449          */
1450         msm_host_writel(msm_host, irq_ack, host,
1451                         msm_offset->core_pwrctl_ctl);
1452
1453         /*
1454          * If we don't have info regarding the voltage levels supported by
1455          * regulators, don't change the IO PAD PWR SWITCH.
1456          */
1457         if (msm_host->caps_0 & CORE_VOLT_SUPPORT) {
1458                 u32 new_config;
1459                 /*
1460                  * We should unset IO PAD PWR switch only if the register write
1461                  * can set IO lines high and the regulator also switches to 3 V.
1462                  * Else, we should keep the IO PAD PWR switch set.
1463                  * This is applicable to certain targets where eMMC vccq supply
1464                  * is only 1.8V. In such targets, even during REQ_IO_HIGH, the
1465                  * IO PAD PWR switch must be kept set to reflect actual
1466                  * regulator voltage. This way, during initialization of
1467                  * controllers with only 1.8V, we will set the IO PAD bit
1468                  * without waiting for a REQ_IO_LOW.
1469                  */
1470                 config = readl_relaxed(host->ioaddr +
1471                                 msm_offset->core_vendor_spec);
1472                 new_config = config;
1473
1474                 if ((io_level & REQ_IO_HIGH) &&
1475                                 (msm_host->caps_0 & CORE_3_0V_SUPPORT))
1476                         new_config &= ~CORE_IO_PAD_PWR_SWITCH;
1477                 else if ((io_level & REQ_IO_LOW) ||
1478                                 (msm_host->caps_0 & CORE_1_8V_SUPPORT))
1479                         new_config |= CORE_IO_PAD_PWR_SWITCH;
1480
1481                 if (config ^ new_config)
1482                         writel_relaxed(new_config, host->ioaddr +
1483                                         msm_offset->core_vendor_spec);
1484         }
1485
1486         if (pwr_state)
1487                 msm_host->curr_pwr_state = pwr_state;
1488         if (io_level)
1489                 msm_host->curr_io_level = io_level;
1490
1491         pr_debug("%s: %s: Handled IRQ(%d), irq_status=0x%x, ack=0x%x\n",
1492                 mmc_hostname(msm_host->mmc), __func__, irq, irq_status,
1493                 irq_ack);
1494 }
1495
1496 static irqreturn_t sdhci_msm_pwr_irq(int irq, void *data)
1497 {
1498         struct sdhci_host *host = (struct sdhci_host *)data;
1499         struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1500         struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
1501
1502         sdhci_msm_handle_pwr_irq(host, irq);
1503         msm_host->pwr_irq_flag = 1;
1504         sdhci_msm_complete_pwr_irq_wait(msm_host);
1505
1506
1507         return IRQ_HANDLED;
1508 }
1509
1510 static unsigned int sdhci_msm_get_max_clock(struct sdhci_host *host)
1511 {
1512         struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1513         struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
1514         struct clk *core_clk = msm_host->bulk_clks[0].clk;
1515
1516         return clk_round_rate(core_clk, ULONG_MAX);
1517 }
1518
1519 static unsigned int sdhci_msm_get_min_clock(struct sdhci_host *host)
1520 {
1521         return SDHCI_MSM_MIN_CLOCK;
1522 }
1523
1524 /**
1525  * __sdhci_msm_set_clock - sdhci_msm clock control.
1526  *
1527  * Description:
1528  * MSM controller does not use internal divider and
1529  * instead directly control the GCC clock as per
1530  * HW recommendation.
1531  **/
1532 static void __sdhci_msm_set_clock(struct sdhci_host *host, unsigned int clock)
1533 {
1534         u16 clk;
1535         /*
1536          * Keep actual_clock as zero -
1537          * - since there is no divider used so no need of having actual_clock.
1538          * - MSM controller uses SDCLK for data timeout calculation. If
1539          *   actual_clock is zero, host->clock is taken for calculation.
1540          */
1541         host->mmc->actual_clock = 0;
1542
1543         sdhci_writew(host, 0, SDHCI_CLOCK_CONTROL);
1544
1545         if (clock == 0)
1546                 return;
1547
1548         /*
1549          * MSM controller do not use clock divider.
1550          * Thus read SDHCI_CLOCK_CONTROL and only enable
1551          * clock with no divider value programmed.
1552          */
1553         clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
1554         sdhci_enable_clk(host, clk);
1555 }
1556
1557 /* sdhci_msm_set_clock - Called with (host->lock) spinlock held. */
1558 static void sdhci_msm_set_clock(struct sdhci_host *host, unsigned int clock)
1559 {
1560         struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1561         struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
1562
1563         if (!clock) {
1564                 msm_host->clk_rate = clock;
1565                 goto out;
1566         }
1567
1568         sdhci_msm_hc_select_mode(host);
1569
1570         msm_set_clock_rate_for_bus_mode(host, clock);
1571 out:
1572         __sdhci_msm_set_clock(host, clock);
1573 }
1574
1575 /*****************************************************************************\
1576  *                                                                           *
1577  * MSM Command Queue Engine (CQE)                                            *
1578  *                                                                           *
1579 \*****************************************************************************/
1580
1581 static u32 sdhci_msm_cqe_irq(struct sdhci_host *host, u32 intmask)
1582 {
1583         int cmd_error = 0;
1584         int data_error = 0;
1585
1586         if (!sdhci_cqe_irq(host, intmask, &cmd_error, &data_error))
1587                 return intmask;
1588
1589         cqhci_irq(host->mmc, intmask, cmd_error, data_error);
1590         return 0;
1591 }
1592
1593 static void sdhci_msm_cqe_disable(struct mmc_host *mmc, bool recovery)
1594 {
1595         struct sdhci_host *host = mmc_priv(mmc);
1596         unsigned long flags;
1597         u32 ctrl;
1598
1599         /*
1600          * When CQE is halted, the legacy SDHCI path operates only
1601          * on 16-byte descriptors in 64bit mode.
1602          */
1603         if (host->flags & SDHCI_USE_64_BIT_DMA)
1604                 host->desc_sz = 16;
1605
1606         spin_lock_irqsave(&host->lock, flags);
1607
1608         /*
1609          * During CQE command transfers, command complete bit gets latched.
1610          * So s/w should clear command complete interrupt status when CQE is
1611          * either halted or disabled. Otherwise unexpected SDCHI legacy
1612          * interrupt gets triggered when CQE is halted/disabled.
1613          */
1614         ctrl = sdhci_readl(host, SDHCI_INT_ENABLE);
1615         ctrl |= SDHCI_INT_RESPONSE;
1616         sdhci_writel(host,  ctrl, SDHCI_INT_ENABLE);
1617         sdhci_writel(host, SDHCI_INT_RESPONSE, SDHCI_INT_STATUS);
1618
1619         spin_unlock_irqrestore(&host->lock, flags);
1620
1621         sdhci_cqe_disable(mmc, recovery);
1622 }
1623
1624 static const struct cqhci_host_ops sdhci_msm_cqhci_ops = {
1625         .enable         = sdhci_cqe_enable,
1626         .disable        = sdhci_msm_cqe_disable,
1627 };
1628
1629 static int sdhci_msm_cqe_add_host(struct sdhci_host *host,
1630                                 struct platform_device *pdev)
1631 {
1632         struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1633         struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
1634         struct cqhci_host *cq_host;
1635         bool dma64;
1636         u32 cqcfg;
1637         int ret;
1638
1639         /*
1640          * When CQE is halted, SDHC operates only on 16byte ADMA descriptors.
1641          * So ensure ADMA table is allocated for 16byte descriptors.
1642          */
1643         if (host->caps & SDHCI_CAN_64BIT)
1644                 host->alloc_desc_sz = 16;
1645
1646         ret = sdhci_setup_host(host);
1647         if (ret)
1648                 return ret;
1649
1650         cq_host = cqhci_pltfm_init(pdev);
1651         if (IS_ERR(cq_host)) {
1652                 ret = PTR_ERR(cq_host);
1653                 dev_err(&pdev->dev, "cqhci-pltfm init: failed: %d\n", ret);
1654                 goto cleanup;
1655         }
1656
1657         msm_host->mmc->caps2 |= MMC_CAP2_CQE | MMC_CAP2_CQE_DCMD;
1658         cq_host->ops = &sdhci_msm_cqhci_ops;
1659
1660         dma64 = host->flags & SDHCI_USE_64_BIT_DMA;
1661
1662         ret = cqhci_init(cq_host, host->mmc, dma64);
1663         if (ret) {
1664                 dev_err(&pdev->dev, "%s: CQE init: failed (%d)\n",
1665                                 mmc_hostname(host->mmc), ret);
1666                 goto cleanup;
1667         }
1668
1669         /* Disable cqe reset due to cqe enable signal */
1670         cqcfg = cqhci_readl(cq_host, CQHCI_VENDOR_CFG1);
1671         cqcfg |= CQHCI_VENDOR_DIS_RST_ON_CQ_EN;
1672         cqhci_writel(cq_host, cqcfg, CQHCI_VENDOR_CFG1);
1673
1674         /*
1675          * SDHC expects 12byte ADMA descriptors till CQE is enabled.
1676          * So limit desc_sz to 12 so that the data commands that are sent
1677          * during card initialization (before CQE gets enabled) would
1678          * get executed without any issues.
1679          */
1680         if (host->flags & SDHCI_USE_64_BIT_DMA)
1681                 host->desc_sz = 12;
1682
1683         ret = __sdhci_add_host(host);
1684         if (ret)
1685                 goto cleanup;
1686
1687         dev_info(&pdev->dev, "%s: CQE init: success\n",
1688                         mmc_hostname(host->mmc));
1689         return ret;
1690
1691 cleanup:
1692         sdhci_cleanup_host(host);
1693         return ret;
1694 }
1695
1696 /*
1697  * Platform specific register write functions. This is so that, if any
1698  * register write needs to be followed up by platform specific actions,
1699  * they can be added here. These functions can go to sleep when writes
1700  * to certain registers are done.
1701  * These functions are relying on sdhci_set_ios not using spinlock.
1702  */
1703 static int __sdhci_msm_check_write(struct sdhci_host *host, u16 val, int reg)
1704 {
1705         struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
1706         struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
1707         u32 req_type = 0;
1708
1709         switch (reg) {
1710         case SDHCI_HOST_CONTROL2:
1711                 req_type = (val & SDHCI_CTRL_VDD_180) ? REQ_IO_LOW :
1712                         REQ_IO_HIGH;
1713                 break;
1714         case SDHCI_SOFTWARE_RESET:
1715                 if (host->pwr && (val & SDHCI_RESET_ALL))
1716                         req_type = REQ_BUS_OFF;
1717                 break;
1718         case SDHCI_POWER_CONTROL:
1719                 req_type = !val ? REQ_BUS_OFF : REQ_BUS_ON;
1720                 break;
1721         case SDHCI_TRANSFER_MODE:
1722                 msm_host->transfer_mode = val;
1723                 break;
1724         case SDHCI_COMMAND:
1725                 if (!msm_host->use_cdr)
1726                         break;
1727                 if ((msm_host->transfer_mode & SDHCI_TRNS_READ) &&
1728                     SDHCI_GET_CMD(val) != MMC_SEND_TUNING_BLOCK_HS200 &&
1729                     SDHCI_GET_CMD(val) != MMC_SEND_TUNING_BLOCK)
1730                         sdhci_msm_set_cdr(host, true);
1731                 else
1732                         sdhci_msm_set_cdr(host, false);
1733                 break;
1734         }
1735
1736         if (req_type) {
1737                 msm_host->pwr_irq_flag = 0;
1738                 /*
1739                  * Since this register write may trigger a power irq, ensure
1740                  * all previous register writes are complete by this point.
1741                  */
1742                 mb();
1743         }
1744         return req_type;
1745 }
1746
1747 /* This function may sleep*/
1748 static void sdhci_msm_writew(struct sdhci_host *host, u16 val, int reg)
1749 {
1750         u32 req_type = 0;
1751
1752         req_type = __sdhci_msm_check_write(host, val, reg);
1753         writew_relaxed(val, host->ioaddr + reg);
1754
1755         if (req_type)
1756                 sdhci_msm_check_power_status(host, req_type);
1757 }
1758
1759 /* This function may sleep*/
1760 static void sdhci_msm_writeb(struct sdhci_host *host, u8 val, int reg)
1761 {
1762         u32 req_type = 0;
1763
1764         req_type = __sdhci_msm_check_write(host, val, reg);
1765
1766         writeb_relaxed(val, host->ioaddr + reg);
1767
1768         if (req_type)
1769                 sdhci_msm_check_power_status(host, req_type);
1770 }
1771
1772 static void sdhci_msm_set_regulator_caps(struct sdhci_msm_host *msm_host)
1773 {
1774         struct mmc_host *mmc = msm_host->mmc;
1775         struct regulator *supply = mmc->supply.vqmmc;
1776         u32 caps = 0, config;
1777         struct sdhci_host *host = mmc_priv(mmc);
1778         const struct sdhci_msm_offset *msm_offset = msm_host->offset;
1779
1780         if (!IS_ERR(mmc->supply.vqmmc)) {
1781                 if (regulator_is_supported_voltage(supply, 1700000, 1950000))
1782                         caps |= CORE_1_8V_SUPPORT;
1783                 if (regulator_is_supported_voltage(supply, 2700000, 3600000))
1784                         caps |= CORE_3_0V_SUPPORT;
1785
1786                 if (!caps)
1787                         pr_warn("%s: 1.8/3V not supported for vqmmc\n",
1788                                         mmc_hostname(mmc));
1789         }
1790
1791         if (caps) {
1792                 /*
1793                  * Set the PAD_PWR_SWITCH_EN bit so that the PAD_PWR_SWITCH
1794                  * bit can be used as required later on.
1795                  */
1796                 u32 io_level = msm_host->curr_io_level;
1797
1798                 config = readl_relaxed(host->ioaddr +
1799                                 msm_offset->core_vendor_spec);
1800                 config |= CORE_IO_PAD_PWR_SWITCH_EN;
1801
1802                 if ((io_level & REQ_IO_HIGH) && (caps & CORE_3_0V_SUPPORT))
1803                         config &= ~CORE_IO_PAD_PWR_SWITCH;
1804                 else if ((io_level & REQ_IO_LOW) || (caps & CORE_1_8V_SUPPORT))
1805                         config |= CORE_IO_PAD_PWR_SWITCH;
1806
1807                 writel_relaxed(config,
1808                                 host->ioaddr + msm_offset->core_vendor_spec);
1809         }
1810         msm_host->caps_0 |= caps;
1811         pr_debug("%s: supported caps: 0x%08x\n", mmc_hostname(mmc), caps);
1812 }
1813
1814 static const struct sdhci_msm_variant_ops mci_var_ops = {
1815         .msm_readl_relaxed = sdhci_msm_mci_variant_readl_relaxed,
1816         .msm_writel_relaxed = sdhci_msm_mci_variant_writel_relaxed,
1817 };
1818
1819 static const struct sdhci_msm_variant_ops v5_var_ops = {
1820         .msm_readl_relaxed = sdhci_msm_v5_variant_readl_relaxed,
1821         .msm_writel_relaxed = sdhci_msm_v5_variant_writel_relaxed,
1822 };
1823
1824 static const struct sdhci_msm_variant_info sdhci_msm_mci_var = {
1825         .var_ops = &mci_var_ops,
1826         .offset = &sdhci_msm_mci_offset,
1827 };
1828
1829 static const struct sdhci_msm_variant_info sdhci_msm_v5_var = {
1830         .mci_removed = true,
1831         .var_ops = &v5_var_ops,
1832         .offset = &sdhci_msm_v5_offset,
1833 };
1834
1835 static const struct sdhci_msm_variant_info sdm845_sdhci_var = {
1836         .mci_removed = true,
1837         .restore_dll_config = true,
1838         .var_ops = &v5_var_ops,
1839         .offset = &sdhci_msm_v5_offset,
1840 };
1841
1842 static const struct of_device_id sdhci_msm_dt_match[] = {
1843         {.compatible = "qcom,sdhci-msm-v4", .data = &sdhci_msm_mci_var},
1844         {.compatible = "qcom,sdhci-msm-v5", .data = &sdhci_msm_v5_var},
1845         {.compatible = "qcom,sdm845-sdhci", .data = &sdm845_sdhci_var},
1846         {},
1847 };
1848
1849 MODULE_DEVICE_TABLE(of, sdhci_msm_dt_match);
1850
1851 static const struct sdhci_ops sdhci_msm_ops = {
1852         .reset = sdhci_reset,
1853         .set_clock = sdhci_msm_set_clock,
1854         .get_min_clock = sdhci_msm_get_min_clock,
1855         .get_max_clock = sdhci_msm_get_max_clock,
1856         .set_bus_width = sdhci_set_bus_width,
1857         .set_uhs_signaling = sdhci_msm_set_uhs_signaling,
1858         .write_w = sdhci_msm_writew,
1859         .write_b = sdhci_msm_writeb,
1860         .irq    = sdhci_msm_cqe_irq,
1861 };
1862
1863 static const struct sdhci_pltfm_data sdhci_msm_pdata = {
1864         .quirks = SDHCI_QUIRK_BROKEN_CARD_DETECTION |
1865                   SDHCI_QUIRK_SINGLE_POWER_WRITE |
1866                   SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN,
1867         .quirks2 = SDHCI_QUIRK2_PRESET_VALUE_BROKEN,
1868         .ops = &sdhci_msm_ops,
1869 };
1870
1871 static int sdhci_msm_probe(struct platform_device *pdev)
1872 {
1873         struct sdhci_host *host;
1874         struct sdhci_pltfm_host *pltfm_host;
1875         struct sdhci_msm_host *msm_host;
1876         struct clk *clk;
1877         int ret;
1878         u16 host_version, core_minor;
1879         u32 core_version, config;
1880         u8 core_major;
1881         const struct sdhci_msm_offset *msm_offset;
1882         const struct sdhci_msm_variant_info *var_info;
1883         struct device_node *node = pdev->dev.of_node;
1884
1885         host = sdhci_pltfm_init(pdev, &sdhci_msm_pdata, sizeof(*msm_host));
1886         if (IS_ERR(host))
1887                 return PTR_ERR(host);
1888
1889         host->sdma_boundary = 0;
1890         pltfm_host = sdhci_priv(host);
1891         msm_host = sdhci_pltfm_priv(pltfm_host);
1892         msm_host->mmc = host->mmc;
1893         msm_host->pdev = pdev;
1894
1895         ret = mmc_of_parse(host->mmc);
1896         if (ret)
1897                 goto pltfm_free;
1898
1899         /*
1900          * Based on the compatible string, load the required msm host info from
1901          * the data associated with the version info.
1902          */
1903         var_info = of_device_get_match_data(&pdev->dev);
1904
1905         msm_host->mci_removed = var_info->mci_removed;
1906         msm_host->restore_dll_config = var_info->restore_dll_config;
1907         msm_host->var_ops = var_info->var_ops;
1908         msm_host->offset = var_info->offset;
1909
1910         msm_offset = msm_host->offset;
1911
1912         sdhci_get_of_property(pdev);
1913
1914         msm_host->saved_tuning_phase = INVALID_TUNING_PHASE;
1915
1916         /* Setup SDCC bus voter clock. */
1917         msm_host->bus_clk = devm_clk_get(&pdev->dev, "bus");
1918         if (!IS_ERR(msm_host->bus_clk)) {
1919                 /* Vote for max. clk rate for max. performance */
1920                 ret = clk_set_rate(msm_host->bus_clk, INT_MAX);
1921                 if (ret)
1922                         goto pltfm_free;
1923                 ret = clk_prepare_enable(msm_host->bus_clk);
1924                 if (ret)
1925                         goto pltfm_free;
1926         }
1927
1928         /* Setup main peripheral bus clock */
1929         clk = devm_clk_get(&pdev->dev, "iface");
1930         if (IS_ERR(clk)) {
1931                 ret = PTR_ERR(clk);
1932                 dev_err(&pdev->dev, "Peripheral clk setup failed (%d)\n", ret);
1933                 goto bus_clk_disable;
1934         }
1935         msm_host->bulk_clks[1].clk = clk;
1936
1937         /* Setup SDC MMC clock */
1938         clk = devm_clk_get(&pdev->dev, "core");
1939         if (IS_ERR(clk)) {
1940                 ret = PTR_ERR(clk);
1941                 dev_err(&pdev->dev, "SDC MMC clk setup failed (%d)\n", ret);
1942                 goto bus_clk_disable;
1943         }
1944         msm_host->bulk_clks[0].clk = clk;
1945
1946         /* Vote for maximum clock rate for maximum performance */
1947         ret = clk_set_rate(clk, INT_MAX);
1948         if (ret)
1949                 dev_warn(&pdev->dev, "core clock boost failed\n");
1950
1951         clk = devm_clk_get(&pdev->dev, "cal");
1952         if (IS_ERR(clk))
1953                 clk = NULL;
1954         msm_host->bulk_clks[2].clk = clk;
1955
1956         clk = devm_clk_get(&pdev->dev, "sleep");
1957         if (IS_ERR(clk))
1958                 clk = NULL;
1959         msm_host->bulk_clks[3].clk = clk;
1960
1961         ret = clk_bulk_prepare_enable(ARRAY_SIZE(msm_host->bulk_clks),
1962                                       msm_host->bulk_clks);
1963         if (ret)
1964                 goto bus_clk_disable;
1965
1966         /*
1967          * xo clock is needed for FLL feature of cm_dll.
1968          * In case if xo clock is not mentioned in DT, warn and proceed.
1969          */
1970         msm_host->xo_clk = devm_clk_get(&pdev->dev, "xo");
1971         if (IS_ERR(msm_host->xo_clk)) {
1972                 ret = PTR_ERR(msm_host->xo_clk);
1973                 dev_warn(&pdev->dev, "TCXO clk not present (%d)\n", ret);
1974         }
1975
1976         if (!msm_host->mci_removed) {
1977                 msm_host->core_mem = devm_platform_ioremap_resource(pdev, 1);
1978                 if (IS_ERR(msm_host->core_mem)) {
1979                         ret = PTR_ERR(msm_host->core_mem);
1980                         goto clk_disable;
1981                 }
1982         }
1983
1984         /* Reset the vendor spec register to power on reset state */
1985         writel_relaxed(CORE_VENDOR_SPEC_POR_VAL,
1986                         host->ioaddr + msm_offset->core_vendor_spec);
1987
1988         if (!msm_host->mci_removed) {
1989                 /* Set HC_MODE_EN bit in HC_MODE register */
1990                 msm_host_writel(msm_host, HC_MODE_EN, host,
1991                                 msm_offset->core_hc_mode);
1992                 config = msm_host_readl(msm_host, host,
1993                                 msm_offset->core_hc_mode);
1994                 config |= FF_CLK_SW_RST_DIS;
1995                 msm_host_writel(msm_host, config, host,
1996                                 msm_offset->core_hc_mode);
1997         }
1998
1999         host_version = readw_relaxed((host->ioaddr + SDHCI_HOST_VERSION));
2000         dev_dbg(&pdev->dev, "Host Version: 0x%x Vendor Version 0x%x\n",
2001                 host_version, ((host_version & SDHCI_VENDOR_VER_MASK) >>
2002                                SDHCI_VENDOR_VER_SHIFT));
2003
2004         core_version = msm_host_readl(msm_host, host,
2005                         msm_offset->core_mci_version);
2006         core_major = (core_version & CORE_VERSION_MAJOR_MASK) >>
2007                       CORE_VERSION_MAJOR_SHIFT;
2008         core_minor = core_version & CORE_VERSION_MINOR_MASK;
2009         dev_dbg(&pdev->dev, "MCI Version: 0x%08x, major: 0x%04x, minor: 0x%02x\n",
2010                 core_version, core_major, core_minor);
2011
2012         if (core_major == 1 && core_minor >= 0x42)
2013                 msm_host->use_14lpp_dll_reset = true;
2014
2015         /*
2016          * SDCC 5 controller with major version 1, minor version 0x34 and later
2017          * with HS 400 mode support will use CM DLL instead of CDC LP 533 DLL.
2018          */
2019         if (core_major == 1 && core_minor < 0x34)
2020                 msm_host->use_cdclp533 = true;
2021
2022         /*
2023          * Support for some capabilities is not advertised by newer
2024          * controller versions and must be explicitly enabled.
2025          */
2026         if (core_major >= 1 && core_minor != 0x11 && core_minor != 0x12) {
2027                 config = readl_relaxed(host->ioaddr + SDHCI_CAPABILITIES);
2028                 config |= SDHCI_CAN_VDD_300 | SDHCI_CAN_DO_8BIT;
2029                 writel_relaxed(config, host->ioaddr +
2030                                 msm_offset->core_vendor_spec_capabilities0);
2031         }
2032
2033         if (core_major == 1 && core_minor >= 0x49)
2034                 msm_host->updated_ddr_cfg = true;
2035
2036         /*
2037          * Power on reset state may trigger power irq if previous status of
2038          * PWRCTL was either BUS_ON or IO_HIGH_V. So before enabling pwr irq
2039          * interrupt in GIC, any pending power irq interrupt should be
2040          * acknowledged. Otherwise power irq interrupt handler would be
2041          * fired prematurely.
2042          */
2043         sdhci_msm_handle_pwr_irq(host, 0);
2044
2045         /*
2046          * Ensure that above writes are propogated before interrupt enablement
2047          * in GIC.
2048          */
2049         mb();
2050
2051         /* Setup IRQ for handling power/voltage tasks with PMIC */
2052         msm_host->pwr_irq = platform_get_irq_byname(pdev, "pwr_irq");
2053         if (msm_host->pwr_irq < 0) {
2054                 ret = msm_host->pwr_irq;
2055                 goto clk_disable;
2056         }
2057
2058         sdhci_msm_init_pwr_irq_wait(msm_host);
2059         /* Enable pwr irq interrupts */
2060         msm_host_writel(msm_host, INT_MASK, host,
2061                 msm_offset->core_pwrctl_mask);
2062
2063         ret = devm_request_threaded_irq(&pdev->dev, msm_host->pwr_irq, NULL,
2064                                         sdhci_msm_pwr_irq, IRQF_ONESHOT,
2065                                         dev_name(&pdev->dev), host);
2066         if (ret) {
2067                 dev_err(&pdev->dev, "Request IRQ failed (%d)\n", ret);
2068                 goto clk_disable;
2069         }
2070
2071         pm_runtime_get_noresume(&pdev->dev);
2072         pm_runtime_set_active(&pdev->dev);
2073         pm_runtime_enable(&pdev->dev);
2074         pm_runtime_set_autosuspend_delay(&pdev->dev,
2075                                          MSM_MMC_AUTOSUSPEND_DELAY_MS);
2076         pm_runtime_use_autosuspend(&pdev->dev);
2077
2078         host->mmc_host_ops.execute_tuning = sdhci_msm_execute_tuning;
2079         if (of_property_read_bool(node, "supports-cqe"))
2080                 ret = sdhci_msm_cqe_add_host(host, pdev);
2081         else
2082                 ret = sdhci_add_host(host);
2083         if (ret)
2084                 goto pm_runtime_disable;
2085         sdhci_msm_set_regulator_caps(msm_host);
2086
2087         pm_runtime_mark_last_busy(&pdev->dev);
2088         pm_runtime_put_autosuspend(&pdev->dev);
2089
2090         return 0;
2091
2092 pm_runtime_disable:
2093         pm_runtime_disable(&pdev->dev);
2094         pm_runtime_set_suspended(&pdev->dev);
2095         pm_runtime_put_noidle(&pdev->dev);
2096 clk_disable:
2097         clk_bulk_disable_unprepare(ARRAY_SIZE(msm_host->bulk_clks),
2098                                    msm_host->bulk_clks);
2099 bus_clk_disable:
2100         if (!IS_ERR(msm_host->bus_clk))
2101                 clk_disable_unprepare(msm_host->bus_clk);
2102 pltfm_free:
2103         sdhci_pltfm_free(pdev);
2104         return ret;
2105 }
2106
2107 static int sdhci_msm_remove(struct platform_device *pdev)
2108 {
2109         struct sdhci_host *host = platform_get_drvdata(pdev);
2110         struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
2111         struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
2112         int dead = (readl_relaxed(host->ioaddr + SDHCI_INT_STATUS) ==
2113                     0xffffffff);
2114
2115         sdhci_remove_host(host, dead);
2116
2117         pm_runtime_get_sync(&pdev->dev);
2118         pm_runtime_disable(&pdev->dev);
2119         pm_runtime_put_noidle(&pdev->dev);
2120
2121         clk_bulk_disable_unprepare(ARRAY_SIZE(msm_host->bulk_clks),
2122                                    msm_host->bulk_clks);
2123         if (!IS_ERR(msm_host->bus_clk))
2124                 clk_disable_unprepare(msm_host->bus_clk);
2125         sdhci_pltfm_free(pdev);
2126         return 0;
2127 }
2128
2129 static __maybe_unused int sdhci_msm_runtime_suspend(struct device *dev)
2130 {
2131         struct sdhci_host *host = dev_get_drvdata(dev);
2132         struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
2133         struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
2134
2135         clk_bulk_disable_unprepare(ARRAY_SIZE(msm_host->bulk_clks),
2136                                    msm_host->bulk_clks);
2137
2138         return 0;
2139 }
2140
2141 static __maybe_unused int sdhci_msm_runtime_resume(struct device *dev)
2142 {
2143         struct sdhci_host *host = dev_get_drvdata(dev);
2144         struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
2145         struct sdhci_msm_host *msm_host = sdhci_pltfm_priv(pltfm_host);
2146         int ret;
2147
2148         ret = clk_bulk_prepare_enable(ARRAY_SIZE(msm_host->bulk_clks),
2149                                        msm_host->bulk_clks);
2150         if (ret)
2151                 return ret;
2152         /*
2153          * Whenever core-clock is gated dynamically, it's needed to
2154          * restore the SDR DLL settings when the clock is ungated.
2155          */
2156         if (msm_host->restore_dll_config && msm_host->clk_rate)
2157                 return sdhci_msm_restore_sdr_dll_config(host);
2158
2159         return 0;
2160 }
2161
2162 static const struct dev_pm_ops sdhci_msm_pm_ops = {
2163         SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend,
2164                                 pm_runtime_force_resume)
2165         SET_RUNTIME_PM_OPS(sdhci_msm_runtime_suspend,
2166                            sdhci_msm_runtime_resume,
2167                            NULL)
2168 };
2169
2170 static struct platform_driver sdhci_msm_driver = {
2171         .probe = sdhci_msm_probe,
2172         .remove = sdhci_msm_remove,
2173         .driver = {
2174                    .name = "sdhci_msm",
2175                    .of_match_table = sdhci_msm_dt_match,
2176                    .pm = &sdhci_msm_pm_ops,
2177         },
2178 };
2179
2180 module_platform_driver(sdhci_msm_driver);
2181
2182 MODULE_DESCRIPTION("Qualcomm Secure Digital Host Controller Interface driver");
2183 MODULE_LICENSE("GPL v2");