2 # Serial device configuration
10 config SERIAL_EARLYCON
13 Support for early consoles with the earlycon parameter. This enables
14 the console before standard serial driver is probed. The console is
15 enabled when early_param is processed.
17 source "drivers/tty/serial/8250/Kconfig"
19 comment "Non-8250 serial port support"
21 config SERIAL_AMBA_PL010
22 tristate "ARM AMBA PL010 serial port support"
26 This selects the ARM(R) AMBA(R) PrimeCell PL010 UART. If you have
27 an Integrator/AP or Integrator/PP2 platform, or if you have a
28 Cirrus Logic EP93xx CPU, say Y or M here.
32 config SERIAL_AMBA_PL010_CONSOLE
33 bool "Support for console on AMBA serial port"
34 depends on SERIAL_AMBA_PL010=y
35 select SERIAL_CORE_CONSOLE
37 Say Y here if you wish to use an AMBA PrimeCell UART as the system
38 console (the system console is the device which receives all kernel
39 messages and warnings and which allows logins in single user mode).
41 Even if you say Y here, the currently visible framebuffer console
42 (/dev/tty0) will still be used as the system console by default, but
43 you can alter that using a kernel command line option such as
44 "console=ttyAM0". (Try "man bootparam" or see the documentation of
45 your boot loader (lilo or loadlin) about how to pass options to the
48 config SERIAL_AMBA_PL011
49 tristate "ARM AMBA PL011 serial port support"
53 This selects the ARM(R) AMBA(R) PrimeCell PL011 UART. If you have
54 an Integrator/PP2, Integrator/CP or Versatile platform, say Y or M
59 config SERIAL_AMBA_PL011_CONSOLE
60 bool "Support for console on AMBA serial port"
61 depends on SERIAL_AMBA_PL011=y
62 select SERIAL_CORE_CONSOLE
63 select SERIAL_EARLYCON
65 Say Y here if you wish to use an AMBA PrimeCell UART as the system
66 console (the system console is the device which receives all kernel
67 messages and warnings and which allows logins in single user mode).
69 Even if you say Y here, the currently visible framebuffer console
70 (/dev/tty0) will still be used as the system console by default, but
71 you can alter that using a kernel command line option such as
72 "console=ttyAMA0". (Try "man bootparam" or see the documentation of
73 your boot loader (lilo or loadlin) about how to pass options to the
76 config SERIAL_EARLYCON_ARM_SEMIHOST
77 bool "Early console using ARM semihosting"
78 depends on ARM64 || ARM
80 select SERIAL_CORE_CONSOLE
81 select SERIAL_EARLYCON
83 Support for early debug console using ARM semihosting. This enables
84 the console before standard serial driver is probed. This is enabled
85 with "earlycon=smh" on the kernel command line. The console is
86 enabled when early_param is processed.
88 config SERIAL_EARLYCON_RISCV_SBI
89 bool "Early console using RISC-V SBI"
92 select SERIAL_CORE_CONSOLE
93 select SERIAL_EARLYCON
95 Support for early debug console using RISC-V SBI. This enables
96 the console before standard serial driver is probed. This is enabled
97 with "earlycon=sbi" on the kernel command line. The console is
98 enabled when early_param is processed.
100 config SERIAL_SB1250_DUART
101 tristate "BCM1xxx on-chip DUART serial support"
102 depends on SIBYTE_SB1xxx_SOC=y
106 Support for the asynchronous serial interface (DUART) included in
107 the BCM1250 and derived System-On-a-Chip (SOC) devices. Note that
108 the letter D in DUART stands for "dual", which is how the device
109 is implemented. Depending on the SOC configuration there may be
110 one or more DUARTs available of which all are handled.
112 If unsure, say Y. To compile this driver as a module, choose M here:
113 the module will be called sb1250-duart.
115 config SERIAL_SB1250_DUART_CONSOLE
116 bool "Support for console on a BCM1xxx DUART serial port"
117 depends on SERIAL_SB1250_DUART=y
118 select SERIAL_CORE_CONSOLE
121 If you say Y here, it will be possible to use a serial port as the
122 system console (the system console is the device which receives all
123 kernel messages and warnings and which allows logins in single user
129 bool "AT91 on-chip serial port support"
130 depends on ARCH_AT91 || COMPILE_TEST
132 select SERIAL_MCTRL_GPIO if GPIOLIB
133 select MFD_AT91_USART
135 This enables the driver for the on-chip UARTs of the Atmel
138 config SERIAL_ATMEL_CONSOLE
139 bool "Support for console on AT91 serial port"
140 depends on SERIAL_ATMEL=y
141 select SERIAL_CORE_CONSOLE
143 Say Y here if you wish to use an on-chip UART on a Atmel
144 AT91 processor as the system console (the system
145 console is the device which receives all kernel messages and
146 warnings and which allows logins in single user mode).
148 config SERIAL_ATMEL_PDC
149 bool "Support DMA transfers on AT91 serial port"
150 depends on SERIAL_ATMEL
153 Say Y here if you wish to use the PDC to do DMA transfers to
154 and from the Atmel AT91 serial port. In order to
155 actually use DMA transfers, make sure that the use_dma_tx
156 and use_dma_rx members in the atmel_uart_data struct is set
157 appropriately for each port.
159 Note that break and error handling currently doesn't work
160 properly when DMA is enabled. Make sure that ports where
161 this matters don't use DMA.
163 config SERIAL_ATMEL_TTYAT
164 bool "Install as device ttyATn instead of ttySn"
165 depends on SERIAL_ATMEL=y
167 Say Y here if you wish to have the internal AT91 UARTs
168 appear as /dev/ttyATn (major 204, minor starting at 154)
169 instead of the normal /dev/ttySn (major 4, minor starting at
170 64). This is necessary if you also want other UARTs, such as
171 external 8250/16C550 compatible UARTs.
172 The ttySn nodes are legally reserved for the 8250 serial driver
173 but are often misused by other serial drivers.
175 To use this, you should create suitable ttyATn device nodes in
176 /dev/, and pass "console=ttyATn" to the kernel.
178 Say Y if you have an external 8250/16C550 UART. If unsure, say N.
180 config SERIAL_KGDB_NMI
181 bool "Serial console over KGDB NMI debugger port"
182 depends on KGDB_SERIAL_CONSOLE
184 This special driver allows you to temporary use NMI debugger port
185 as a normal console (assuming that the port is attached to KGDB).
187 Unlike KDB's disable_nmi command, with this driver you are always
188 able to go back to the debugger using KGDB escape sequence ($3#33).
189 This is because this console driver processes the input in NMI
190 context, and thus is able to intercept the magic sequence.
192 Note that since the console interprets input and uses polling
193 communication methods, for things like PPP you still must fully
194 detach debugger port from the KGDB NMI (i.e. disable_nmi), and
200 bool "Micrel KS8695 (Centaur) serial port support"
201 depends on ARCH_KS8695
204 This selects the Micrel Centaur KS8695 UART. Say Y here.
206 config SERIAL_KS8695_CONSOLE
207 bool "Support for console on KS8695 (Centaur) serial port"
208 depends on SERIAL_KS8695=y
209 select SERIAL_CORE_CONSOLE
211 Say Y here if you wish to use a KS8695 (Centaur) UART as the
212 system console (the system console is the device which
213 receives all kernel messages and warnings and which allows
214 logins in single user mode).
217 tristate "Meson serial port support"
218 depends on ARCH_MESON
221 This enables the driver for the on-chip UARTs of the Amlogic
224 config SERIAL_MESON_CONSOLE
225 bool "Support for console on meson"
226 depends on SERIAL_MESON=y
227 select SERIAL_CORE_CONSOLE
228 select SERIAL_EARLYCON
230 Say Y here if you wish to use a Amlogic MesonX UART as the
231 system console (the system console is the device which
232 receives all kernel messages and warnings and which allows
233 logins in single user mode) as /dev/ttyAMLx.
235 config SERIAL_CLPS711X
236 tristate "CLPS711X serial port support"
237 depends on ARCH_CLPS711X || COMPILE_TEST
239 select SERIAL_MCTRL_GPIO if GPIOLIB
241 This enables the driver for the on-chip UARTs of the Cirrus
242 Logic EP711x/EP721x/EP731x processors.
244 config SERIAL_CLPS711X_CONSOLE
245 bool "Support for console on CLPS711X serial port"
246 depends on SERIAL_CLPS711X=y
247 select SERIAL_CORE_CONSOLE
249 Even if you say Y here, the currently visible virtual console
250 (/dev/tty0) will still be used as the system console by default, but
251 you can alter that using a kernel command line option such as
254 config SERIAL_SAMSUNG
255 tristate "Samsung SoC serial support"
256 depends on PLAT_SAMSUNG || ARCH_EXYNOS
259 Support for the on-chip UARTs on the Samsung S3C24XX series CPUs,
260 providing /dev/ttySAC0, 1 and 2 (note, some machines may not
261 provide all of these ports, depending on how the serial port
264 config SERIAL_SAMSUNG_UARTS_4
266 depends on SERIAL_SAMSUNG
267 default y if !(CPU_S3C2410 || CPU_S3C2412 || CPU_S3C2440 || CPU_S3C2442)
269 Internal node for the common case of 4 Samsung compatible UARTs
271 config SERIAL_SAMSUNG_UARTS
273 depends on SERIAL_SAMSUNG
274 default 4 if SERIAL_SAMSUNG_UARTS_4 || CPU_S3C2416
277 Select the number of available UART ports for the Samsung S3C
280 config SERIAL_SAMSUNG_DEBUG
281 bool "Samsung SoC serial debug"
282 depends on SERIAL_SAMSUNG && DEBUG_LL
284 Add support for debugging the serial driver. Since this is
285 generally being used as a console, we use our own output
286 routines that go via the low-level debug printascii()
289 config SERIAL_SAMSUNG_CONSOLE
290 bool "Support for console on Samsung SoC serial port"
291 depends on SERIAL_SAMSUNG=y
292 select SERIAL_CORE_CONSOLE
293 select SERIAL_EARLYCON
295 Allow selection of the S3C24XX on-board serial ports for use as
298 Even if you say Y here, the currently visible virtual console
299 (/dev/tty0) will still be used as the system console by default, but
300 you can alter that using a kernel command line option such as
301 "console=ttySACx". (Try "man bootparam" or see the documentation of
302 your boot loader about how to pass options to the kernel at
305 config SERIAL_SIRFSOC
306 tristate "SiRF SoC Platform Serial port support"
310 Support for the on-chip UART on the CSR SiRFprimaII series,
311 providing /dev/ttySiRF0, 1 and 2 (note, some machines may not
312 provide all of these ports, depending on how the serial port
313 pins are configured).
315 config SERIAL_SIRFSOC_CONSOLE
316 bool "Support for console on SiRF SoC serial port"
317 depends on SERIAL_SIRFSOC=y
318 select SERIAL_CORE_CONSOLE
320 Even if you say Y here, the currently visible virtual console
321 (/dev/tty0) will still be used as the system console by default, but
322 you can alter that using a kernel command line option such as
323 "console=ttySiRFx". (Try "man bootparam" or see the documentation of
324 your boot loader about how to pass options to the kernel at
328 tristate "NVIDIA Tegra20/30 SoC serial controller"
329 depends on ARCH_TEGRA && TEGRA20_APB_DMA
332 Support for the on-chip UARTs on the NVIDIA Tegra series SOCs
333 providing /dev/ttyTHS0, 1, 2, 3 and 4 (note, some machines may not
334 provide all of these ports, depending on how the serial port
335 are enabled). This driver uses the APB DMA to achieve higher baudrate
336 and better performance.
338 config SERIAL_MAX3100
339 tristate "MAX3100 support"
345 config SERIAL_MAX310X
346 tristate "MAX310X support"
347 depends on SPI_MASTER
349 select REGMAP_SPI if SPI_MASTER
352 This selects support for an advanced UART from Maxim (Dallas).
353 Supported ICs are MAX3107, MAX3108, MAX3109, MAX14830.
354 Each IC contains 128 words each of receive and transmit FIFO
355 that can be controlled through I2C or high-speed SPI.
357 Say Y here if you want to support this ICs.
360 bool "DECstation DZ serial driver"
361 depends on MACH_DECSTATION && 32BIT
365 DZ11-family serial controllers for DECstations and VAXstations,
366 including the DC7085, M7814, and M7819.
368 config SERIAL_DZ_CONSOLE
369 bool "Support console on DECstation DZ serial driver"
370 depends on SERIAL_DZ=y
371 select SERIAL_CORE_CONSOLE
374 If you say Y here, it will be possible to use a serial port as the
375 system console (the system console is the device which receives all
376 kernel messages and warnings and which allows logins in single user
379 Note that the firmware uses ttyS3 as the serial console on
380 DECstations that use this driver.
385 tristate "DECstation Z85C30 serial support"
386 depends on MACH_DECSTATION
390 Support for the Zilog 85C350 serial communications controller used
391 for serial ports in newer DECstation systems. These include the
392 DECsystem 5900 and all models of the DECstation and DECsystem 5000
393 systems except from model 200.
395 If unsure, say Y. To compile this driver as a module, choose M here:
396 the module will be called zs.
398 config SERIAL_ZS_CONSOLE
399 bool "Support for console on a DECstation Z85C30 serial port"
400 depends on SERIAL_ZS=y
401 select SERIAL_CORE_CONSOLE
404 If you say Y here, it will be possible to use a serial port as the
405 system console (the system console is the device which receives all
406 kernel messages and warnings and which allows logins in single user
409 Note that the firmware uses ttyS1 as the serial console on the
410 Maxine and ttyS3 on the others using this driver.
415 tristate "DC21285 serial port support"
416 depends on FOOTBRIDGE
419 If you have a machine based on a 21285 (Footbridge) StrongARM(R)/
420 PCI bridge you can enable its onboard serial port by enabling this
423 config SERIAL_21285_CONSOLE
424 bool "Console on DC21285 serial port"
425 depends on SERIAL_21285=y
426 select SERIAL_CORE_CONSOLE
428 If you have enabled the serial port on the 21285 footbridge you can
429 make it the console by answering Y to this option.
431 Even if you say Y here, the currently visible virtual console
432 (/dev/tty0) will still be used as the system console by default, but
433 you can alter that using a kernel command line option such as
434 "console=ttyFB". (Try "man bootparam" or see the documentation of
435 your boot loader (lilo or loadlin) about how to pass options to the
436 kernel at boot time.)
439 bool "Marvell MPSC serial port support"
443 Say Y here if you want to use the Marvell MPSC serial controller.
445 config SERIAL_MPSC_CONSOLE
446 bool "Support for console on Marvell MPSC serial port"
447 depends on SERIAL_MPSC
448 select SERIAL_CORE_CONSOLE
450 Say Y here if you want to support a serial console on a Marvell MPSC.
453 bool "PXA serial port support (DEPRECATED)"
454 depends on ARCH_PXA || ARCH_MMP
456 select SERIAL_8250_PXA if SERIAL_8250=y
457 select SERIAL_PXA_NON8250 if !SERIAL_8250=y
459 If you have a machine based on an Intel XScale PXA2xx CPU you
460 can enable its onboard serial ports by enabling this option.
462 Unless you have a specific need, you should use SERIAL_8250_PXA
465 config SERIAL_PXA_NON8250
467 depends on !SERIAL_8250
469 config SERIAL_PXA_CONSOLE
470 bool "Console on PXA serial port (DEPRECATED)"
471 depends on SERIAL_PXA
472 select SERIAL_CORE_CONSOLE
473 select SERIAL_8250_CONSOLE if SERIAL_8250=y
475 If you have enabled the serial port on the Intel XScale PXA
476 CPU you can make it the console by answering Y to this option.
478 Even if you say Y here, the currently visible virtual console
479 (/dev/tty0) will still be used as the system console by default, but
480 you can alter that using a kernel command line option such as
481 "console=ttySA0". (Try "man bootparam" or see the documentation of
482 your boot loader (lilo or loadlin) about how to pass options to the
483 kernel at boot time.)
485 Unless you have a specific need, you should use SERIAL_8250_PXA
486 and SERIAL_8250_CONSOLE instead of this.
489 bool "SA1100 serial port support"
490 depends on ARCH_SA1100
493 If you have a machine based on a SA1100/SA1110 StrongARM(R) CPU you
494 can enable its onboard serial port by enabling this option.
495 Please read <file:Documentation/arm/SA1100/serial_UART> for further
498 config SERIAL_SA1100_CONSOLE
499 bool "Console on SA1100 serial port"
500 depends on SERIAL_SA1100
501 select SERIAL_CORE_CONSOLE
503 If you have enabled the serial port on the SA1100/SA1110 StrongARM
504 CPU you can make it the console by answering Y to this option.
506 Even if you say Y here, the currently visible virtual console
507 (/dev/tty0) will still be used as the system console by default, but
508 you can alter that using a kernel command line option such as
509 "console=ttySA0". (Try "man bootparam" or see the documentation of
510 your boot loader (lilo or loadlin) about how to pass options to the
511 kernel at boot time.)
514 tristate "IMX serial port support"
515 depends on ARCH_MXC || COMPILE_TEST
518 select SERIAL_MCTRL_GPIO if GPIOLIB
520 If you have a machine based on a Motorola IMX CPU you
521 can enable its onboard serial port by enabling this option.
523 config SERIAL_IMX_CONSOLE
524 bool "Console on IMX serial port"
525 depends on SERIAL_IMX=y
526 select SERIAL_CORE_CONSOLE
527 select SERIAL_EARLYCON if OF
529 If you have enabled the serial port on the Freescale IMX
530 CPU you can make it the console by answering Y to this option.
532 Even if you say Y here, the currently visible virtual console
533 (/dev/tty0) will still be used as the system console by default, but
534 you can alter that using a kernel command line option such as
535 "console=ttymxc0". (Try "man bootparam" or see the documentation of
536 your bootloader about how to pass options to the kernel at boot time.)
538 config SERIAL_UARTLITE
539 tristate "Xilinx uartlite serial port support"
543 Say Y here if you want to use the Xilinx uartlite serial controller.
545 To compile this driver as a module, choose M here: the
546 module will be called uartlite.
548 config SERIAL_UARTLITE_CONSOLE
549 bool "Support for console on Xilinx uartlite serial port"
550 depends on SERIAL_UARTLITE=y
551 select SERIAL_CORE_CONSOLE
552 select SERIAL_EARLYCON
554 Say Y here if you wish to use a Xilinx uartlite as the system
555 console (the system console is the device which receives all kernel
556 messages and warnings and which allows logins in single user mode).
558 config SERIAL_UARTLITE_NR_UARTS
559 int "Maximum number of uartlite serial ports"
560 depends on SERIAL_UARTLITE
564 Set this to the number of uartlites in your system, or the number
565 you think you might implement.
567 config SERIAL_SUNCORE
571 select SERIAL_CORE_CONSOLE
574 config SERIAL_SUNZILOG
575 tristate "Sun Zilog8530 serial support"
578 This driver supports the Zilog8530 serial ports found on many Sparc
579 systems. Say Y or M if you want to be able to these serial ports.
581 config SERIAL_SUNZILOG_CONSOLE
582 bool "Console on Sun Zilog8530 serial port"
583 depends on SERIAL_SUNZILOG=y
585 If you would like to be able to use the Zilog8530 serial port
586 on your Sparc system as the console, you can do so by answering
590 tristate "Sun SU serial support"
591 depends on SPARC && PCI
593 This driver supports the 8250 serial ports that run the keyboard and
594 mouse on (PCI) UltraSPARC systems. Say Y or M if you want to be able
595 to these serial ports.
597 config SERIAL_SUNSU_CONSOLE
598 bool "Console on Sun SU serial port"
599 depends on SERIAL_SUNSU=y
601 If you would like to be able to use the SU serial port
602 on your Sparc system as the console, you can do so by answering
606 tristate "Serial MUX support"
611 Saying Y here will enable the hardware MUX serial driver for
612 the Nova, K class systems and D class with a 'remote control card'.
613 The hardware MUX is not 8250/16550 compatible therefore the
614 /dev/ttyB0 device is shared between the Serial MUX and the PDC
615 software console. The following steps need to be completed to use
618 1. create the device entry (mknod /dev/ttyB0 c 11 0)
619 2. Edit the /etc/inittab to start a getty listening on /dev/ttyB0
620 3. Add device ttyB0 to /etc/securetty (if you want to log on as
621 root on this console.)
622 4. Change the kernel command console parameter to: console=ttyB0
624 config SERIAL_MUX_CONSOLE
625 bool "Support for console on serial MUX"
626 depends on SERIAL_MUX=y
627 select SERIAL_CORE_CONSOLE
631 bool "PDC software console support"
632 depends on PARISC && !SERIAL_MUX && VT
635 Saying Y here will enable the software based PDC console to be
636 used as the system console. This is useful for machines in
637 which the hardware based console has not been written yet. The
638 following steps must be completed to use the PDC console:
640 1. create the device entry (mknod /dev/ttyB0 c 11 0)
641 2. Edit the /etc/inittab to start a getty listening on /dev/ttyB0
642 3. Add device ttyB0 to /etc/securetty (if you want to log on as
643 root on this console.)
644 4. Change the kernel command console parameter to: console=ttyB0
647 tristate "Sun Siemens SAB82532 serial support"
648 depends on SPARC && PCI
650 This driver supports the Siemens SAB82532 DUSCC serial ports on newer
651 (PCI) UltraSPARC systems. Say Y or M if you want to be able to these
654 config SERIAL_SUNSAB_CONSOLE
655 bool "Console on Sun Siemens SAB82532 serial port"
656 depends on SERIAL_SUNSAB=y
658 If you would like to be able to use the SAB82532 serial port
659 on your Sparc system as the console, you can do so by answering
663 bool "Sun4v Hypervisor Console support"
666 This driver supports the console device found on SUN4V Sparc
667 systems. Say Y if you want to be able to use this device.
669 config SERIAL_IP22_ZILOG
670 tristate "SGI Zilog8530 serial support"
671 depends on SGI_HAS_ZILOG
674 This driver supports the Zilog8530 serial ports found on SGI
675 systems. Say Y or M if you want to be able to these serial ports.
677 config SERIAL_IP22_ZILOG_CONSOLE
678 bool "Console on SGI Zilog8530 serial port"
679 depends on SERIAL_IP22_ZILOG=y
680 select SERIAL_CORE_CONSOLE
683 tristate "SuperH SCI(F) serial port support"
684 depends on SUPERH || ARCH_RENESAS || H8300 || COMPILE_TEST
686 select SERIAL_MCTRL_GPIO if GPIOLIB
688 config SERIAL_SH_SCI_NR_UARTS
689 int "Maximum number of SCI(F) serial ports" if EXPERT
692 depends on SERIAL_SH_SCI
694 default "10" if SUPERH
695 default "18" if ARCH_RENESAS
698 config SERIAL_SH_SCI_CONSOLE
699 bool "Support for console on SuperH SCI(F)" if EXPERT
700 depends on SERIAL_SH_SCI=y
701 select SERIAL_CORE_CONSOLE
704 config SERIAL_SH_SCI_EARLYCON
705 bool "Support for early console on SuperH SCI(F)" if EXPERT
706 depends on SERIAL_SH_SCI=y
707 select SERIAL_CORE_CONSOLE
708 select SERIAL_EARLYCON
709 default ARCH_RENESAS || H8300
711 config SERIAL_SH_SCI_DMA
712 bool "DMA support" if EXPERT
713 depends on SERIAL_SH_SCI && DMA_ENGINE
716 config SERIAL_PNX8XXX
717 bool "Enable PNX8XXX SoCs' UART Support"
718 depends on SOC_PNX833X
721 If you have a MIPS-based Philips SoC such as PNX8330 and you want
722 to use serial ports, say Y. Otherwise, say N.
724 config SERIAL_PNX8XXX_CONSOLE
725 bool "Enable PNX8XX0 serial console"
726 depends on SERIAL_PNX8XXX
727 select SERIAL_CORE_CONSOLE
729 If you have a MIPS-based Philips SoC such as PNX8330 and you want
730 to use serial console, say Y. Otherwise, say N.
732 config SERIAL_HS_LPC32XX
733 tristate "LPC32XX high speed serial port support"
734 depends on ARCH_LPC32XX && OF
737 Support for the LPC32XX high speed serial ports (up to 900kbps).
738 Those are UARTs completely different from the Standard UARTs on the
740 Choose M or Y here to build this driver.
742 config SERIAL_HS_LPC32XX_CONSOLE
743 bool "Enable LPC32XX high speed UART serial console"
744 depends on SERIAL_HS_LPC32XX=y
745 select SERIAL_CORE_CONSOLE
747 If you would like to be able to use one of the high speed serial
748 ports on the LPC32XX as the console, you can do so by answering
754 config SERIAL_CORE_CONSOLE
761 bool "Coldfire serial support"
765 This serial driver supports the Freescale Coldfire serial ports.
767 config SERIAL_MCF_BAUDRATE
768 int "Default baudrate for Coldfire serial ports"
769 depends on SERIAL_MCF
772 This setting lets you define what the default baudrate is for the
773 ColdFire serial ports. The usual default varies from board to board,
774 and this setting is a way of catering for that.
776 config SERIAL_MCF_CONSOLE
777 bool "Coldfire serial console support"
778 depends on SERIAL_MCF
779 select SERIAL_CORE_CONSOLE
781 Enable a ColdFire internal serial port to be the system console.
783 config SERIAL_PMACZILOG
784 tristate "Mac or PowerMac z85c30 ESCC support"
785 depends on (M68K && MAC) || PPC_PMAC
788 This driver supports the Zilog z85C30 serial ports found on
790 Say Y or M if you want to be able to these serial ports.
792 config SERIAL_PMACZILOG_TTYS
793 bool "Use ttySn device nodes for Zilog z85c30"
794 depends on SERIAL_PMACZILOG
796 The pmac_zilog driver for the z85C30 chip on many powermacs
797 historically used the device numbers for /dev/ttySn. The
798 8250 serial port driver also uses these numbers, which means
799 the two drivers being unable to coexist; you could not use
800 both z85C30 and 8250 type ports at the same time.
802 If this option is not selected, the pmac_zilog driver will
803 use the device numbers allocated for /dev/ttyPZn. This allows
804 the pmac_zilog and 8250 drivers to co-exist, but may cause
805 existing userspace setups to break. Programs that need to
806 access the built-in serial ports on powermacs will need to
807 be reconfigured to use /dev/ttyPZn instead of /dev/ttySn.
809 If you enable this option, any z85c30 ports in the system will
810 be registered as ttyS0 onwards as in the past, and you will be
811 unable to use the 8250 module for PCMCIA or other 16C550-style
814 Say N unless you need the z85c30 ports on your (Power)Mac
815 to appear as /dev/ttySn.
817 config SERIAL_PMACZILOG_CONSOLE
818 bool "Console on Mac or PowerMac z85c30 serial port"
819 depends on SERIAL_PMACZILOG=y
820 select SERIAL_CORE_CONSOLE
822 If you would like to be able to use the z85c30 serial port
823 on your (Power)Mac as the console, you can do so by answering
827 tristate "CPM SCC/SMC serial port support"
828 depends on CPM2 || CPM1
831 This driver supports the SCC and SMC serial ports on Motorola
832 embedded PowerPC that contain a CPM1 (8xx) or CPM2 (8xxx)
834 config SERIAL_CPM_CONSOLE
835 bool "Support for console on CPM SCC/SMC serial port"
836 depends on SERIAL_CPM=y
837 select SERIAL_CORE_CONSOLE
839 Say Y here if you wish to use a SCC or SMC CPM UART as the system
840 console (the system console is the device which receives all kernel
841 messages and warnings and which allows logins in single user mode).
843 Even if you say Y here, the currently visible framebuffer console
844 (/dev/tty0) will still be used as the system console by default, but
845 you can alter that using a kernel command line option such as
846 "console=ttyCPM0". (Try "man bootparam" or see the documentation of
847 your boot loader (lilo or loadlin) about how to pass options to the
848 kernel at boot time.)
850 config SERIAL_SGI_L1_CONSOLE
851 bool "SGI Altix L1 serial console support"
852 depends on IA64_GENERIC || IA64_SGI_SN2
854 select SERIAL_CORE_CONSOLE
856 If you have an SGI Altix and you would like to use the system
857 controller serial port as your console (you want this!),
858 say Y. Otherwise, say N.
861 tristate "Microchip PIC32 serial support"
862 depends on MACH_PIC32
865 If you have a PIC32, this driver supports the serial ports.
867 Say Y or M to use PIC32 serial ports, otherwise say N. Note that
868 to use a serial port as a console, this must be included in kernel and
871 config SERIAL_PIC32_CONSOLE
872 bool "PIC32 serial console support"
873 depends on SERIAL_PIC32
874 select SERIAL_CORE_CONSOLE
876 If you have a PIC32, this driver supports the putting a console on one
879 Say Y to use the PIC32 console, otherwise say N.
881 config SERIAL_MPC52xx
882 tristate "Freescale MPC52xx/MPC512x family PSC serial support"
883 depends on PPC_MPC52xx || PPC_MPC512x
886 This driver supports MPC52xx and MPC512x PSC serial ports. If you would
887 like to use them, you must answer Y or M to this option. Note that
888 for use as console, it must be included in kernel and not as a
891 config SERIAL_MPC52xx_CONSOLE
892 bool "Console on a Freescale MPC52xx/MPC512x family PSC serial port"
893 depends on SERIAL_MPC52xx=y
894 select SERIAL_CORE_CONSOLE
896 Select this options if you'd like to use one of the PSC serial port
897 of the Freescale MPC52xx family as a console.
899 config SERIAL_MPC52xx_CONSOLE_BAUD
900 int "Freescale MPC52xx/MPC512x family PSC serial port baud"
901 depends on SERIAL_MPC52xx_CONSOLE=y
904 Select the MPC52xx console baud rate.
905 This value is only used if the bootloader doesn't pass in the
909 tristate "IBM Multiport Serial Adapter"
910 depends on PCI && PPC_PSERIES
914 This driver is for a family of multiport serial adapters
915 including 2 port RVX, 2 port internal modem, 4 port internal
916 modem and a split 1 port RVX and 1 port internal modem.
918 This driver can also be built as a module. If so, the module
922 bool "TMPTX39XX/49XX SIO support"
923 depends on HAS_TXX9_SERIAL
927 config HAS_TXX9_SERIAL
930 config SERIAL_TXX9_NR_UARTS
931 int "Maximum number of TMPTX39XX/49XX SIO ports"
932 depends on SERIAL_TXX9
935 config SERIAL_TXX9_CONSOLE
936 bool "TMPTX39XX/49XX SIO Console support"
937 depends on SERIAL_TXX9=y
938 select SERIAL_CORE_CONSOLE
940 config SERIAL_TXX9_STDSERIAL
941 bool "TX39XX/49XX SIO act as standard serial"
942 depends on !SERIAL_8250 && SERIAL_TXX9
945 tristate "NEC VR4100 series Serial Interface Unit support"
946 depends on CPU_VR41XX
949 If you have a NEC VR4100 series processor and you want to use
950 Serial Interface Unit(SIU) or Debug Serial Interface Unit(DSIU)
951 (not include VR4111/VR4121 DSIU), say Y. Otherwise, say N.
953 config SERIAL_VR41XX_CONSOLE
954 bool "Enable NEC VR4100 series Serial Interface Unit console"
955 depends on SERIAL_VR41XX=y
956 select SERIAL_CORE_CONSOLE
958 If you have a NEC VR4100 series processor and you want to use
959 a console on a serial port, say Y. Otherwise, say N.
962 tristate "Digi International NEO and Classic PCI Support"
966 This is a driver for Digi International's Neo and Classic series
967 of cards which provide multiple serial ports. You would need
968 something like this to connect more than two modems to your Linux
969 box, for instance in order to become a dial-in server. This driver
970 supports PCI boards only.
972 If you have a card like this, say Y here, otherwise say N.
974 To compile this driver as a module, choose M here: the
975 module will be called jsm.
977 config SERIAL_SGI_IOC4
978 tristate "SGI IOC4 controller serial support"
979 depends on (IA64_GENERIC || IA64_SGI_SN2) && SGI_IOC4
982 If you have an SGI Altix with an IOC4 based Base IO card
983 and wish to use the serial ports on this card, say Y.
986 config SERIAL_SGI_IOC3
987 tristate "SGI Altix IOC3 serial support"
988 depends on (IA64_GENERIC || IA64_SGI_SN2) && SGI_IOC3
991 If you have an SGI Altix with an IOC3 serial card,
992 say Y or M. Otherwise, say N.
995 tristate "MSM on-chip serial port support"
999 config SERIAL_MSM_CONSOLE
1000 bool "MSM serial console support"
1001 depends on SERIAL_MSM=y
1002 select SERIAL_CORE_CONSOLE
1003 select SERIAL_EARLYCON
1005 config SERIAL_QCOM_GENI
1006 tristate "QCOM on-chip GENI based serial port support"
1007 depends on ARCH_QCOM || COMPILE_TEST
1008 depends on QCOM_GENI_SE
1011 config SERIAL_QCOM_GENI_CONSOLE
1012 bool "QCOM GENI Serial Console support"
1013 depends on SERIAL_QCOM_GENI=y
1014 select SERIAL_CORE_CONSOLE
1015 select SERIAL_EARLYCON
1017 Serial console driver for Qualcomm Technologies Inc's GENI based
1020 config SERIAL_VT8500
1021 bool "VIA VT8500 on-chip serial port support"
1022 depends on ARCH_VT8500
1025 config SERIAL_VT8500_CONSOLE
1026 bool "VIA VT8500 serial console support"
1027 depends on SERIAL_VT8500=y
1028 select SERIAL_CORE_CONSOLE
1031 tristate "NetX serial port support"
1032 depends on ARCH_NETX
1035 If you have a machine based on a Hilscher NetX SoC you
1036 can enable its onboard serial port by enabling this option.
1038 To compile this driver as a module, choose M here: the
1039 module will be called netx-serial.
1041 config SERIAL_NETX_CONSOLE
1042 bool "Console on NetX serial port"
1043 depends on SERIAL_NETX=y
1044 select SERIAL_CORE_CONSOLE
1046 If you have enabled the serial port on the Hilscher NetX SoC
1047 you can make it the console by answering Y to this option.
1050 tristate "OMAP serial port support"
1051 depends on ARCH_OMAP2PLUS
1054 If you have a machine based on an Texas Instruments OMAP CPU you
1055 can enable its onboard serial ports by enabling this option.
1057 By enabling this option you take advantage of dma feature available
1058 with the omap-serial driver. DMA support can be enabled from platform
1061 config SERIAL_OMAP_CONSOLE
1062 bool "Console on OMAP serial port"
1063 depends on SERIAL_OMAP=y
1064 select SERIAL_CORE_CONSOLE
1066 Select this option if you would like to use omap serial port as
1069 Even if you say Y here, the currently visible virtual console
1070 (/dev/tty0) will still be used as the system console by default, but
1071 you can alter that using a kernel command line option such as
1072 "console=ttyOx". (Try "man bootparam" or see the documentation of
1073 your boot loader about how to pass options to the kernel at
1076 config SERIAL_LANTIQ
1077 bool "Lantiq serial driver"
1080 select SERIAL_CORE_CONSOLE
1081 select SERIAL_EARLYCON
1083 Support for console and UART on Lantiq SoCs.
1086 tristate "Freescale QUICC Engine serial port support"
1087 depends on QUICC_ENGINE
1092 This driver supports the QE serial ports on Freescale embedded
1093 PowerPC that contain a QUICC Engine.
1095 config SERIAL_SCCNXP
1096 tristate "SCCNXP serial port support"
1099 This selects support for an advanced UART from NXP (Philips).
1100 Supported ICs are SCC2681, SCC2691, SCC2692, SC28L91, SC28L92,
1101 SC28L202, SCC68681 and SCC68692.
1103 config SERIAL_SCCNXP_CONSOLE
1104 bool "Console on SCCNXP serial port"
1105 depends on SERIAL_SCCNXP=y
1106 select SERIAL_CORE_CONSOLE
1108 Support for console on SCCNXP serial ports.
1110 config SERIAL_SC16IS7XX_CORE
1113 config SERIAL_SC16IS7XX
1114 tristate "SC16IS7xx serial support"
1116 depends on (SPI_MASTER && !I2C) || I2C
1118 This selects support for SC16IS7xx serial ports.
1119 Supported ICs are SC16IS740, SC16IS741, SC16IS750, SC16IS752,
1120 SC16IS760 and SC16IS762. Select supported buses using options below.
1122 config SERIAL_SC16IS7XX_I2C
1123 bool "SC16IS7xx for I2C interface"
1124 depends on SERIAL_SC16IS7XX
1126 select SERIAL_SC16IS7XX_CORE if SERIAL_SC16IS7XX
1127 select REGMAP_I2C if I2C
1130 Enable SC16IS7xx driver on I2C bus,
1131 If required say y, and say n to i2c if not required,
1132 Enabled by default to support oldconfig.
1133 You must select at least one bus for the driver to be built.
1135 config SERIAL_SC16IS7XX_SPI
1136 bool "SC16IS7xx for spi interface"
1137 depends on SERIAL_SC16IS7XX
1138 depends on SPI_MASTER
1139 select SERIAL_SC16IS7XX_CORE if SERIAL_SC16IS7XX
1140 select REGMAP_SPI if SPI_MASTER
1142 Enable SC16IS7xx driver on SPI bus,
1143 If required say y, and say n to spi if not required,
1144 This is additional support to exsisting driver.
1145 You must select at least one bus for the driver to be built.
1147 config SERIAL_TIMBERDALE
1148 tristate "Support for timberdale UART"
1150 depends on X86_32 || COMPILE_TEST
1152 Add support for UART controller on timberdale.
1154 config SERIAL_BCM63XX
1155 tristate "Broadcom BCM63xx/BCM33xx UART support"
1157 depends on MIPS || ARM || COMPILE_TEST
1159 This enables the driver for the onchip UART core found on
1160 the following chipsets:
1162 BCM33xx (cable modem)
1163 BCM63xx/BCM63xxx (DSL)
1165 BCM7xxx (STB) - DOCSIS console
1167 config SERIAL_BCM63XX_CONSOLE
1168 bool "Console on BCM63xx serial port"
1169 depends on SERIAL_BCM63XX=y
1170 select SERIAL_CORE_CONSOLE
1171 select SERIAL_EARLYCON
1173 If you have enabled the serial port on the BCM63xx CPU
1174 you can make it the console by answering Y to this option.
1176 config SERIAL_GRLIB_GAISLER_APBUART
1177 tristate "GRLIB APBUART serial support"
1178 depends on OF && SPARC
1181 Add support for the GRLIB APBUART serial port.
1183 config SERIAL_GRLIB_GAISLER_APBUART_CONSOLE
1184 bool "Console on GRLIB APBUART serial port"
1185 depends on SERIAL_GRLIB_GAISLER_APBUART=y
1186 select SERIAL_CORE_CONSOLE
1188 Support for running a console on the GRLIB APBUART
1190 config SERIAL_ALTERA_JTAGUART
1191 tristate "Altera JTAG UART support"
1194 This driver supports the Altera JTAG UART port.
1196 config SERIAL_ALTERA_JTAGUART_CONSOLE
1197 bool "Altera JTAG UART console support"
1198 depends on SERIAL_ALTERA_JTAGUART=y
1199 select SERIAL_CORE_CONSOLE
1200 select SERIAL_EARLYCON
1202 Enable a Altera JTAG UART port to be the system console.
1204 config SERIAL_ALTERA_JTAGUART_CONSOLE_BYPASS
1205 bool "Bypass output when no connection"
1206 depends on SERIAL_ALTERA_JTAGUART_CONSOLE
1207 select SERIAL_CORE_CONSOLE
1209 Bypass console output and keep going even if there is no
1210 JTAG terminal connection with the host.
1212 config SERIAL_ALTERA_UART
1213 tristate "Altera UART support"
1216 This driver supports the Altera softcore UART port.
1218 config SERIAL_ALTERA_UART_MAXPORTS
1219 int "Maximum number of Altera UART ports"
1220 depends on SERIAL_ALTERA_UART
1223 This setting lets you define the maximum number of the Altera
1224 UART ports. The usual default varies from board to board, and
1225 this setting is a way of catering for that.
1227 config SERIAL_ALTERA_UART_BAUDRATE
1228 int "Default baudrate for Altera UART ports"
1229 depends on SERIAL_ALTERA_UART
1232 This setting lets you define what the default baudrate is for the
1233 Altera UART ports. The usual default varies from board to board,
1234 and this setting is a way of catering for that.
1236 config SERIAL_ALTERA_UART_CONSOLE
1237 bool "Altera UART console support"
1238 depends on SERIAL_ALTERA_UART=y
1239 select SERIAL_CORE_CONSOLE
1240 select SERIAL_EARLYCON
1242 Enable a Altera UART port to be the system console.
1244 config SERIAL_IFX6X60
1245 tristate "SPI protocol driver for Infineon 6x60 modem (EXPERIMENTAL)"
1246 depends on GPIOLIB || COMPILE_TEST
1247 depends on SPI && HAS_DMA
1249 Support for the IFX6x60 modem devices on Intel MID platforms.
1251 config SERIAL_PCH_UART
1252 tristate "Intel EG20T PCH/LAPIS Semicon IOH(ML7213/ML7223/ML7831) UART"
1253 depends on PCI && (X86_32 || MIPS || COMPILE_TEST)
1256 This driver is for PCH(Platform controller Hub) UART of Intel EG20T
1257 which is an IOH(Input/Output Hub) for x86 embedded processor.
1258 Enabling PCH_DMA, this PCH UART works as DMA mode.
1260 This driver also can be used for LAPIS Semiconductor IOH(Input/
1261 Output Hub), ML7213, ML7223 and ML7831.
1262 ML7213 IOH is for IVI(In-Vehicle Infotainment) use, ML7223 IOH is
1263 for MP(Media Phone) use and ML7831 IOH is for general purpose use.
1264 ML7213/ML7223/ML7831 is companion chip for Intel Atom E6xx series.
1265 ML7213/ML7223/ML7831 is completely compatible for Intel EG20T PCH.
1267 config SERIAL_PCH_UART_CONSOLE
1268 bool "Support for console on Intel EG20T PCH UART/OKI SEMICONDUCTOR ML7213 IOH"
1269 depends on SERIAL_PCH_UART=y
1270 select SERIAL_CORE_CONSOLE
1272 Say Y here if you wish to use the PCH UART as the system console
1273 (the system console is the device which receives all kernel messages and
1274 warnings and which allows logins in single user mode).
1276 config SERIAL_MXS_AUART
1277 tristate "MXS AUART support"
1278 depends on ARCH_MXS || MACH_ASM9260 || COMPILE_TEST
1280 select SERIAL_MCTRL_GPIO if GPIOLIB
1282 This driver supports the MXS and Alphascale ASM9260 Application
1285 config SERIAL_MXS_AUART_CONSOLE
1286 bool "MXS AUART console support"
1287 depends on SERIAL_MXS_AUART=y
1288 select SERIAL_CORE_CONSOLE
1290 Enable a MXS AUART port to be the system console.
1292 config SERIAL_XILINX_PS_UART
1293 tristate "Cadence (Xilinx Zynq) UART support"
1297 This driver supports the Cadence UART. It is found e.g. in Xilinx
1300 config SERIAL_XILINX_PS_UART_CONSOLE
1301 bool "Cadence UART console support"
1302 depends on SERIAL_XILINX_PS_UART=y
1303 select SERIAL_CORE_CONSOLE
1304 select SERIAL_EARLYCON
1306 Enable a Cadence UART port to be the system console.
1308 config SERIAL_AR933X
1309 tristate "AR933X serial port support"
1310 depends on HAVE_CLK && ATH79
1313 If you have an Atheros AR933X SOC based board and want to use the
1314 built-in UART of the SoC, say Y to this option.
1316 To compile this driver as a module, choose M here: the
1317 module will be called ar933x_uart.
1319 config SERIAL_AR933X_CONSOLE
1320 bool "Console on AR933X serial port"
1321 depends on SERIAL_AR933X=y
1322 select SERIAL_CORE_CONSOLE
1324 Enable a built-in UART port of the AR933X to be the system console.
1326 config SERIAL_AR933X_NR_UARTS
1327 int "Maximum number of AR933X serial ports"
1328 depends on SERIAL_AR933X
1331 Set this to the number of serial ports you want the driver
1334 config SERIAL_EFM32_UART
1335 tristate "EFM32 UART/USART port"
1336 depends on ARM && (ARCH_EFM32 || COMPILE_TEST)
1339 This driver support the USART and UART ports on
1340 Energy Micro's efm32 SoCs.
1342 config SERIAL_MPS2_UART_CONSOLE
1343 bool "MPS2 UART console support"
1344 depends on SERIAL_MPS2_UART
1345 select SERIAL_CORE_CONSOLE
1346 select SERIAL_EARLYCON
1348 config SERIAL_MPS2_UART
1349 bool "MPS2 UART port"
1350 depends on ARCH_MPS2 || COMPILE_TEST
1353 This driver support the UART ports on ARM MPS2.
1355 config SERIAL_EFM32_UART_CONSOLE
1356 bool "EFM32 UART/USART console support"
1357 depends on SERIAL_EFM32_UART=y
1358 select SERIAL_CORE_CONSOLE
1361 tristate "ARC UART driver support"
1364 Driver for on-chip UART for ARC(Synopsys) for the legacy
1365 FPGA Boards (ML50x/ARCAngel4)
1367 config SERIAL_ARC_CONSOLE
1368 bool "Console on ARC UART"
1369 depends on SERIAL_ARC=y
1370 select SERIAL_CORE_CONSOLE
1371 select SERIAL_EARLYCON
1373 Enable system Console on ARC UART
1375 config SERIAL_ARC_NR_PORTS
1376 int "Number of ARC UART ports"
1377 depends on SERIAL_ARC
1381 Set this to the number of serial ports you want the driver
1385 tristate "Comtrol RocketPort EXPRESS/INFINITY support"
1389 This driver supports the Comtrol RocketPort EXPRESS and
1390 RocketPort INFINITY families of PCI/PCIe multiport serial adapters.
1391 These adapters use a "RocketPort 2" ASIC that is not compatible
1392 with the original RocketPort driver (CONFIG_ROCKETPORT).
1394 To compile this driver as a module, choose M here: the
1395 module will be called rp2.
1397 If you want to compile this driver into the kernel, say Y here. If
1398 you don't have a suitable RocketPort card installed, say N.
1400 config SERIAL_RP2_NR_UARTS
1401 int "Maximum number of RocketPort EXPRESS/INFINITY ports"
1402 depends on SERIAL_RP2
1405 If multiple cards are present, the default limit of 32 ports may
1406 need to be increased.
1408 config SERIAL_FSL_LPUART
1409 tristate "Freescale lpuart serial port support"
1413 Support for the on-chip lpuart on some Freescale SOCs.
1415 config SERIAL_FSL_LPUART_CONSOLE
1416 bool "Console on Freescale lpuart serial port"
1417 depends on SERIAL_FSL_LPUART=y
1418 select SERIAL_CORE_CONSOLE
1419 select SERIAL_EARLYCON
1421 If you have enabled the lpuart serial port on the Freescale SoCs,
1422 you can make it the console by answering Y to this option.
1424 config SERIAL_CONEXANT_DIGICOLOR
1425 tristate "Conexant Digicolor CX92xxx USART serial port support"
1429 Support for the on-chip USART on Conexant Digicolor SoCs.
1431 config SERIAL_CONEXANT_DIGICOLOR_CONSOLE
1432 bool "Console on Conexant Digicolor serial port"
1433 depends on SERIAL_CONEXANT_DIGICOLOR=y
1434 select SERIAL_CORE_CONSOLE
1436 If you have enabled the USART serial port on Conexant Digicolor
1437 SoCs, you can make it the console by answering Y to this option.
1439 config SERIAL_ST_ASC
1440 tristate "ST ASC serial port support"
1442 depends on ARM || COMPILE_TEST
1444 This driver is for the on-chip Asychronous Serial Controller on
1445 STMicroelectronics STi SoCs.
1446 ASC is embedded in ST COMMS IP block. It supports Rx & Tx functionality.
1447 It support all industry standard baud rates.
1451 config SERIAL_ST_ASC_CONSOLE
1452 bool "Support for console on ST ASC"
1453 depends on SERIAL_ST_ASC=y
1454 select SERIAL_CORE_CONSOLE
1456 config SERIAL_MEN_Z135
1457 tristate "MEN 16z135 Support"
1461 Say yes here to enable support for the MEN 16z135 High Speed UART IP-Core
1464 This driver can also be build as a module. If so, the module will be called
1468 tristate "Support for Spreadtrum serial"
1469 depends on ARCH_SPRD
1472 This enables the driver for the Spreadtrum's serial.
1474 config SERIAL_SPRD_CONSOLE
1475 bool "Spreadtrum UART console support"
1476 depends on SERIAL_SPRD=y
1477 select SERIAL_CORE_CONSOLE
1478 select SERIAL_EARLYCON
1480 Support for early debug console using Spreadtrum's serial. This enables
1481 the console before standard serial driver is probed. This is enabled
1482 with "earlycon" on the kernel command line. The console is
1483 enabled when early_param is processed.
1486 tristate "STMicroelectronics STM32 serial port support"
1488 depends on ARCH_STM32 || COMPILE_TEST
1490 This driver is for the on-chip Serial Controller on
1491 STMicroelectronics STM32 MCUs.
1492 USART supports Rx & Tx functionality.
1493 It support all industry standard baud rates.
1497 config SERIAL_STM32_CONSOLE
1498 bool "Support for console on STM32"
1499 depends on SERIAL_STM32=y
1500 select SERIAL_CORE_CONSOLE
1502 config SERIAL_MVEBU_UART
1503 bool "Marvell EBU serial port support"
1504 depends on ARCH_MVEBU || COMPILE_TEST
1507 This driver is for Marvell EBU SoC's UART. If you have a machine
1508 based on the Armada-3700 SoC and wish to use the on-board serial
1513 config SERIAL_MVEBU_CONSOLE
1514 bool "Console on Marvell EBU serial port"
1515 depends on SERIAL_MVEBU_UART
1516 select SERIAL_CORE_CONSOLE
1517 select SERIAL_EARLYCON
1520 Say 'Y' here if you wish to use Armada-3700 UART as the system console.
1521 (the system console is the device which receives all kernel messages
1522 and warnings and which allows logins in single user mode)
1526 tristate "Actions Semi Owl serial port support"
1527 depends on ARCH_ACTIONS || COMPILE_TEST
1530 This driver is for Actions Semiconductor S500/S900 SoC's UART.
1531 Say 'Y' here if you wish to use the on-board serial port.
1534 config SERIAL_OWL_CONSOLE
1535 bool "Console on Actions Semi Owl serial port"
1536 depends on SERIAL_OWL=y
1537 select SERIAL_CORE_CONSOLE
1538 select SERIAL_EARLYCON
1541 Say 'Y' here if you wish to use Actions Semiconductor S500/S900 UART
1542 as the system console.
1545 bool "RDA Micro serial port support"
1546 depends on ARCH_RDA || COMPILE_TEST
1549 This driver is for RDA8810PL SoC's UART.
1550 Say 'Y' here if you wish to use the on-board serial port.
1553 config SERIAL_RDA_CONSOLE
1554 bool "Console on RDA Micro serial port"
1555 depends on SERIAL_RDA=y
1556 select SERIAL_CORE_CONSOLE
1557 select SERIAL_EARLYCON
1560 Say 'Y' here if you wish to use the RDA8810PL UART as the system
1561 console. Only earlycon is implemented currently.
1565 config SERIAL_MCTRL_GPIO