help
This enables support for the IMG Pistachio SoC platform.
+config MACH_XILFPGA
+ bool "MIPSfpga Xilinx based boards"
+ select ARCH_REQUIRE_GPIOLIB
+ select BOOT_ELF32
+ select BOOT_RAW
+ select BUILTIN_DTB
+ select CEVT_R4K
+ select COMMON_CLK
+ select CSRC_R4K
+ select IRQ_MIPS_CPU
+ select LIBFDT
+ select MIPS_CPU_SCACHE
+ select SYS_HAS_EARLY_PRINTK
+ select SYS_HAS_CPU_MIPS32_R2
+ select SYS_SUPPORTS_32BIT_KERNEL
+ select SYS_SUPPORTS_LITTLE_ENDIAN
+ select SYS_SUPPORTS_ZBOOT_UART16550
+ select USE_OF
+ select USE_GENERIC_EARLY_PRINTK_8250
+ help
+ This enables support for the IMG University Program MIPSfpga platform.
+
config MIPS_MALTA
bool "MIPS Malta board"
select ARCH_MAY_HAVE_PC_FDC
source "arch/mips/loongson64/Kconfig"
source "arch/mips/netlogic/Kconfig"
source "arch/mips/paravirt/Kconfig"
+source "arch/mips/xilfpga/Kconfig"
endmenu
select CPU_SUPPORTS_MSA
select GENERIC_CSUM
select HAVE_KVM
- select MIPS_O32_FP64_SUPPORT
+ select MIPS_O32_FP64_SUPPORT if 32BIT
help
Choose this option to build a kernel for release 6 or later of the
MIPS32 architecture. New MIPS processors, starting with the Warrior
select CPU_MIPSR2_IRQ_VI
select CPU_MIPSR2_IRQ_EI
select SYNC_R4K
- select MIPS_GIC_IPI
+ select MIPS_GIC_IPI if MIPS_GIC
select MIPS_MT
select SMP
select SMP_UP
config MIPS_CMP
bool "MIPS CMP framework support (DEPRECATED)"
depends on SYS_SUPPORTS_MIPS_CMP && !CPU_MIPSR6
- select MIPS_GIC_IPI
+ select MIPS_GIC_IPI if MIPS_GIC
select SMP
select SYNC_R4K
select SYS_SUPPORTS_SMP
select MIPS_CM
select MIPS_CPC
select MIPS_CPS_PM if HOTPLUG_CPU
- select MIPS_GIC_IPI
+ select MIPS_GIC_IPI if MIPS_GIC
select SMP
select SYNC_R4K if (CEVT_R4K || CSRC_R4K)
select SYS_SUPPORTS_HOTPLUG_CPU
bool
config MIPS_GIC_IPI
+ depends on MIPS_GIC
bool
config MIPS_CM
help
Do not enable appended dtb support.
+ config MIPS_ELF_APPENDED_DTB
+ bool "vmlinux"
+ help
+ With this option, the boot code will look for a device tree binary
+ DTB) included in the vmlinux ELF section .appended_dtb. By default
+ it is empty and the DTB can be appended using binutils command
+ objcopy:
+
+ objcopy --update-section .appended_dtb=<filename>.dtb vmlinux
+
+ This is meant as a backward compatiblity convenience for those
+ systems with a bootloader that can't be upgraded to accommodate
+ the documented boot protocol using a device tree.
+
config MIPS_RAW_APPENDED_DTB
bool "vmlinux.bin"
help
choice
prompt "Kernel command line type" if !CMDLINE_OVERRIDE
+ default MIPS_CMDLINE_FROM_DTB if USE_OF && !ATH79 && !MACH_INGENIC && \
+ !MIPS_MALTA && !MIPS_SEAD3 && \
+ !CAVIUM_OCTEON_SOC
default MIPS_CMDLINE_FROM_BOOTLOADER
config MIPS_CMDLINE_FROM_DTB