# SSID to be used in IEEE 802.11 management frames
ssid=test
+# Alternative formats for configuring SSID
+# (double quoted string, hexdump, printf-escaped string)
+#ssid2="test"
+#ssid2=74657374
+#ssid2=P"hello\nthere"
+
+# UTF-8 SSID: Whether the SSID is to be interpreted using UTF-8 encoding
+#utf8_ssid=1
# Country code (ISO/IEC 3166-1). Used to set regulatory domain.
# Set as needed to indicate country in which device is operating.
#ieee80211d=1
# Operation mode (a = IEEE 802.11a, b = IEEE 802.11b, g = IEEE 802.11g,
+# ad = IEEE 802.11ad (60 GHz); a/g options are used with IEEE 802.11n, too, to
+# specify band)
# Default: IEEE 802.11b
hw_mode=g
# requests for broadcast SSID
ignore_broadcast_ssid=0
+# Additional vendor specfic elements for Beacon and Probe Response frames
+# This parameter can be used to add additional vendor specific element(s) into
+# the end of the Beacon and Probe Response frames. The format for these
+# element(s) is a hexdump of the raw information elements (id+len+payload for
+# one or more elements)
+#vendor_elements=dd0411223301
+
# TX queue parameters (EDCF / bursting)
# tx_queue_<queue name>_<param>
# queues: data0, data1, data2, data3, after_beacon, beacon
# else reserved (default)
#
# Number of Sounding Dimensions: [SOUNDING-DIMENSION-2]
-# Beamformer\92s capability indicating the maximum value of the NUM_STS parameter
+# Beamformer's capability indicating the maximum value of the NUM_STS parameter
# in the TXVECTOR of a VHT NDP
# If SU beamformer capable, set to maximum value minus 1
# else reserved (default)
# Indicates the maximum length of A-MPDU pre-EOF padding that the STA can recv
# This field is an integer in the range of 0 to 7.
# The length defined by this field is equal to
-# 2 pow(13 + Maximum A-MPDU Length Exponent) \961 octets
+# 2 pow(13 + Maximum A-MPDU Length Exponent) -1 octets
#
# VHT Link Adaptation Capable: [VHT-LINK-ADAPT2] [VHT-LINK-ADAPT3]
# Indicates whether or not the STA supports link adaptation using VHT variant
# 0 = Tx antenna pattern might change during the lifetime of an association
# 1 = Tx antenna pattern does not change during the lifetime of an association
#vht_capab=[SHORT-GI-80][HTC-VHT]
+#
+# Require stations to support VHT PHY (reject association if they do not)
+#require_vht=1
+
+# 0 = 20 or 40 MHz operating Channel width
+# 1 = 80 MHz channel width
+# 2 = 160 MHz channel width
+# 3 = 80+80 MHz channel width
#vht_oper_chwidth=1
+#
+# center freq = 5 GHz + (5 * index)
+# So index 42 gives center freq 5.210 GHz
+# which is channel 42 in 5G band
+#
+#vht_oper_centr_freq_seg0_idx=42
+#
+# center freq = 5 GHz + (5 * index)
+# So index 159 gives center freq 5.795 GHz
+# which is channel 159 in 5G band
+#
+#vht_oper_centr_freq_seg1_idx=159
##### IEEE 802.1X-2004 related configuration ##################################
eap_server=0
# Path for EAP server user database
+# If SQLite support is included, this can be set to "sqlite:/path/to/sqlite.db"
+# to use SQLite database instead of a text file.
#eap_user_file=/etc/hostapd.eap_user
# CA certificate (PEM or DER file) for EAP-TLS/PEAP/TTLS
# This is a text string in implementation specific format. The example
# implementation in eap_sim_db.c uses this as the UNIX domain socket name for
# the HLR/AuC gateway (e.g., hlr_auc_gw). In this case, the path uses "unix:"
-# prefix.
+# prefix. If hostapd is built with SQLite support (CONFIG_SQLITE=y in .config),
+# database file can be described with an optional db=<path> parameter.
#eap_sim_db=unix:/tmp/hlr_auc_gw.sock
+#eap_sim_db=unix:/tmp/hlr_auc_gw.sock db=/tmp/hostapd.db
# Encryption key for EAP-FAST PAC-Opaque values. This key must be a secret,
# random value. It is configured as a 16-octet value in hex format. It can be
# to the bridge.
#vlan_tagged_interface=eth0
+# When hostapd creates a VLAN interface on vlan_tagged_interfaces, it needs
+# to know how to name it.
+# 0 = vlan<XXX>, e.g., vlan1
+# 1 = <vlan_tagged_interface>.<XXX>, e.g. eth0.1
+#vlan_naming=0
+
# Arbitrary RADIUS attributes can be added into Access-Request and
# Accounting-Request packets by specifying the contents of the attributes with
# the following configuration parameters. There can be multiple of these to
# 1 = enabled
#okc=1
+# SAE threshold for anti-clogging mechanism (dot11RSNASAEAntiCloggingThreshold)
+# This parameter defines how many open SAE instances can be in progress at the
+# same time before the anti-clogging mechanism is taken into use.
+#sae_anti_clogging_threshold=5
+
+# Enabled SAE finite cyclic groups
+# SAE implementation are required to support group 19 (ECC group defined over a
+# 256-bit prime order field). All groups that are supported by the
+# implementation are enabled by default. This configuration parameter can be
+# used to specify a limited set of allowed groups. The group values are listed
+# in the IANA registry:
+# http://www.iana.org/assignments/ipsec-registry/ipsec-registry.xml#ipsec-registry-9
+#sae_groups=19 20 21 25 26
##### IEEE 802.11r configuration ##############################################
# 2 = WPS enabled, configured
#wps_state=2
+# Whether to manage this interface independently from other WPS interfaces
+# By default, a single hostapd process applies WPS operations to all configured
+# interfaces. This parameter can be used to disable that behavior for a subset
+# of interfaces. If this is set to non-zero for an interface, WPS commands
+# issued on that interface do not apply to other interfaces and WPS operations
+# performed on other interfaces do not affect this interface.
+#wps_independent=0
+
# AP can be configured into a locked state where new WPS Registrar are not
# accepted, but previously authorized Registrars (including the internal one)
# can continue to add new Enrollees.
# stdoffset[dst[offset][,start[/time],end[/time]]]
#time_zone=EST5
+# WNM-Sleep Mode (extended sleep mode for stations)
+# 0 = disabled (default)
+# 1 = enabled (allow stations to use WNM-Sleep Mode)
+#wnm_sleep_mode=1
+
+# BSS Transition Management
+# 0 = disabled (default)
+# 1 = enabled
+#bss_transition=1
+
##### IEEE 802.11u-2011 #######################################################
# Enable Interworking service
# Arbitrary number of Roaming Consortium OIs can be configured with each line
# adding a new OI to the list. The first three entries are available through
# Beacon and Probe Response frames. Any additional entry will be available only
-# through ANQP queries. Each OI is between 3 and 15 octets and is configured a
+# through ANQP queries. Each OI is between 3 and 15 octets and is configured as
# a hexstring.
#roaming_consortium=021122
#roaming_consortium=2233445566
#venue_name=eng:Example venue
#venue_name=fin:Esimerkkipaikka
+# Network Authentication Type
+# This parameter indicates what type of network authentication is used in the
+# network.
+# format: <network auth type indicator (1-octet hex str)> [redirect URL]
+# Network Authentication Type Indicator values:
+# 00 = Acceptance of terms and conditions
+# 01 = On-line enrollment supported
+# 02 = http/https redirection
+# 03 = DNS redirection
+#network_auth_type=00
+#network_auth_type=02http://www.example.com/redirect/me/here/
+
+# IP Address Type Availability
+# format: <1-octet encoded value as hex str>
+# (ipv4_type & 0x3f) << 2 | (ipv6_type & 0x3)
+# ipv4_type:
+# 0 = Address type not available
+# 1 = Public IPv4 address available
+# 2 = Port-restricted IPv4 address available
+# 3 = Single NATed private IPv4 address available
+# 4 = Double NATed private IPv4 address available
+# 5 = Port-restricted IPv4 address and single NATed IPv4 address available
+# 6 = Port-restricted IPv4 address and double NATed IPv4 address available
+# 7 = Availability of the address type is not known
+# ipv6_type:
+# 0 = Address type not available
+# 1 = Address type available
+# 2 = Availability of the address type not known
+#ipaddr_type_availability=14
+
+# Domain Name
+# format: <variable-octet str>[,<variable-octet str>]
+#domain_name=example.com,another.example.com,yet-another.example.com
+
+# 3GPP Cellular Network information
+# format: <MCC1,MNC1>[;<MCC2,MNC2>][;...]
+#anqp_3gpp_cell_net=244,91;310,026;234,56
+
+# NAI Realm information
+# One or more realm can be advertised. Each nai_realm line adds a new realm to
+# the set. These parameters provide information for stations using Interworking
+# network selection to allow automatic connection to a network based on
+# credentials.
+# format: <encoding>,<NAI Realm(s)>[,<EAP Method 1>][,<EAP Method 2>][,...]
+# encoding:
+# 0 = Realm formatted in accordance with IETF RFC 4282
+# 1 = UTF-8 formatted character string that is not formatted in
+# accordance with IETF RFC 4282
+# NAI Realm(s): Semi-colon delimited NAI Realm(s)
+# EAP Method: <EAP Method>[:<[AuthParam1:Val1]>][<[AuthParam2:Val2]>][...]
+# AuthParam (Table 8-188 in IEEE Std 802.11-2012):
+# ID 2 = Non-EAP Inner Authentication Type
+# 1 = PAP, 2 = CHAP, 3 = MSCHAP, 4 = MSCHAPV2
+# ID 3 = Inner authentication EAP Method Type
+# ID 5 = Credential Type
+# 1 = SIM, 2 = USIM, 3 = NFC Secure Element, 4 = Hardware Token,
+# 5 = Softoken, 6 = Certificate, 7 = username/password, 9 = Anonymous,
+# 10 = Vendor Specific
+#nai_realm=0,example.com;example.net
+# EAP methods EAP-TLS with certificate and EAP-TTLS/MSCHAPv2 with
+# username/password
+#nai_realm=0,example.org,13[5:6],21[2:4][5:7]
+
+##### Hotspot 2.0 #############################################################
+
+# Enable Hotspot 2.0 support
+#hs20=1
+
+# Disable Downstream Group-Addressed Forwarding (DGAF)
+# This can be used to configure a network where no group-addressed frames are
+# allowed. The AP will not forward any group-address frames to the stations and
+# random GTKs are issued for each station to prevent associated stations from
+# forging such frames to other stations in the BSS.
+#disable_dgaf=1
+
+# Operator Friendly Name
+# This parameter can be used to configure one or more Operator Friendly Name
+# Duples. Each entry has a two or three character language code (ISO-639)
+# separated by colon from the operator friendly name string.
+#hs20_oper_friendly_name=eng:Example operator
+#hs20_oper_friendly_name=fin:Esimerkkioperaattori
+
+# Connection Capability
+# This can be used to advertise what type of IP traffic can be sent through the
+# hotspot (e.g., due to firewall allowing/blocking protocols/ports).
+# format: <IP Protocol>:<Port Number>:<Status>
+# IP Protocol: 1 = ICMP, 6 = TCP, 17 = UDP
+# Port Number: 0..65535
+# Status: 0 = Closed, 1 = Open, 2 = Unknown
+# Each hs20_conn_capab line is added to the list of advertised tuples.
+#hs20_conn_capab=1:0:2
+#hs20_conn_capab=6:22:1
+#hs20_conn_capab=17:5060:0
+
+# WAN Metrics
+# format: <WAN Info>:<DL Speed>:<UL Speed>:<DL Load>:<UL Load>:<LMD>
+# WAN Info: B0-B1: Link Status, B2: Symmetric Link, B3: At Capabity
+# (encoded as two hex digits)
+# Link Status: 1 = Link up, 2 = Link down, 3 = Link in test state
+# Downlink Speed: Estimate of WAN backhaul link current downlink speed in kbps;
+# 1..4294967295; 0 = unknown
+# Uplink Speed: Estimate of WAN backhaul link current uplink speed in kbps
+# 1..4294967295; 0 = unknown
+# Downlink Load: Current load of downlink WAN connection (scaled to 255 = 100%)
+# Uplink Load: Current load of uplink WAN connection (scaled to 255 = 100%)
+# Load Measurement Duration: Duration for measuring downlink/uplink load in
+# tenths of a second (1..65535); 0 if load cannot be determined
+#hs20_wan_metrics=01:8000:1000:80:240:3000
+
+# Operating Class Indication
+# List of operating classes the BSSes in this ESS use. The Global operating
+# classes in Table E-4 of IEEE Std 802.11-2012 Annex E define the values that
+# can be used in this.
+# format: hexdump of operating class octets
+# for example, operating classes 81 (2.4 GHz channels 1-13) and 115 (5 GHz
+# channels 36-48):
+#hs20_operating_class=5173
+
##### Multiple BSSID support ##################################################
#
# Above configuration is using the default interface (wlan#, or multi-SSID VLAN
OSDN Git Service
