# inactive stations.
#p2p_go_max_inactivity=300
+# Opportunistic Key Caching (also known as Proactive Key Caching) default
+# This parameter can be used to set the default behavior for the
+# proactive_key_caching parameter. By default, OKC is disabled unless enabled
+# with the global okc=1 parameter or with the per-network
+# proactive_key_caching=1 parameter. With okc=1, OKC is enabled by default, but
+# can be disabled with per-network proactive_key_caching=0 parameter.
+#okc=0
+
+# Protected Management Frames default
+# This parameter can be used to set the default behavior for the ieee80211w
+# parameter. By default, PMF is disabled unless enabled with the global pmf=1/2
+# parameter or with the per-network ieee80211w=1/2 parameter. With pmf=1/2, PMF
+# is enabled/required by default, but can be disabled with the per-network
+# ieee80211w parameter.
+#pmf=0
+
+# Enabled SAE finite cyclic groups in preference order
+# By default (if this parameter is not set), the mandatory group 19 (ECC group
+# defined over a 256-bit prime order field) is preferred, but other groups are
+# also enabled. If this parameter is set, the groups will be tried in the
+# indicated order. The group values are listed in the IANA registry:
+# http://www.iana.org/assignments/ipsec-registry/ipsec-registry.xml#ipsec-registry-9
+#sae_groups=21 20 19 26 25
# Interworking (IEEE 802.11u)
# phase2: Pre-configure Phase 2 (inner authentication) parameters
# This optional field is used with like the 'eap' parameter.
#
+# excluded_ssid: Excluded SSID
+# This optional field can be used to excluded specific SSID(s) from
+# matching with the network. Multiple entries can be used to specify more
+# than one SSID.
+#
# for example:
#
#cred={
# set, scan results that do not match any of the specified frequencies are not
# considered when selecting a BSS.
#
+# bgscan: Background scanning
+# wpa_supplicant behavior for background scanning can be specified by
+# configuring a bgscan module. These modules are responsible for requesting
+# background scans for the purpose of roaming within an ESS (i.e., within a
+# single network block with all the APs using the same SSID). The bgscan
+# parameter uses following format: "<bgscan module name>:<module parameters>"
+# Following bgscan modules are available:
+# simple - Periodic background scans based on signal strength
+# bgscan="simple:<short bgscan interval in seconds>:<signal strength threshold>:
+# <long interval>"
+# bgscan="simple:30:-45:300"
+# learn - Learn channels used by the network and try to avoid bgscans on other
+# channels (experimental)
+# bgscan="learn:<short bgscan interval in seconds>:<signal strength threshold>:
+# <long interval>[:<database file name>]"
+# bgscan="learn:30:-45:300:/etc/wpa_supplicant/network1.bgscan"
+#
# proto: list of accepted protocols
# WPA = WPA/IEEE 802.11i/D3.0
# RSN = WPA2/IEEE 802.11i (also WPA2 can be used as an alias for RSN)
# If not set, this defaults to: WPA-PSK WPA-EAP
#
# ieee80211w: whether management frame protection is enabled
-# 0 = disabled (default)
+# 0 = disabled (default unless changed with the global pmf parameter)
# 1 = optional
# 2 = required
# The most common configuration options for this based on the PMF (protected
#
# proactive_key_caching:
# Enable/disable opportunistic PMKSA caching for WPA2.
-# 0 = disabled (default)
+# 0 = disabled (default unless changed with the global okc parameter)
# 1 = enabled
#
# wep_key0..3: Static WEP key (ASCII in double quotation, e.g. "abcde" or
# DTIM period in Beacon intervals for AP mode (default: 2)
#dtim_period=2
+# disable_ht: Whether HT (802.11n) should be disabled.
+# 0 = HT enabled (if AP supports it)
+# 1 = HT disabled
+#
+# disable_ht40: Whether HT-40 (802.11n) should be disabled.
+# 0 = HT-40 enabled (if AP supports it)
+# 1 = HT-40 disabled
+#
+# disable_sgi: Whether SGI (short guard interval) should be disabled.
+# 0 = SGI enabled (if AP supports it)
+# 1 = SGI disabled
+#
+# ht_mcs: Configure allowed MCS rates.
+# Parsed as an array of bytes, in base-16 (ascii-hex)
+# ht_mcs="" // Use all available (default)
+# ht_mcs="0xff 00 00 00 00 00 00 00 00 00 " // Use MCS 0-7 only
+# ht_mcs="0xff ff 00 00 00 00 00 00 00 00 " // Use MCS 0-15 only
+#
+# disable_max_amsdu: Whether MAX_AMSDU should be disabled.
+# -1 = Do not make any changes.
+# 0 = Enable MAX-AMSDU if hardware supports it.
+# 1 = Disable AMSDU
+#
+# ampdu_density: Allow overriding AMPDU density configuration.
+# Treated as hint by the kernel.
+# -1 = Do not make any changes.
+# 0-3 = Set AMPDU density (aka factor) to specified value.
+
# Example blocks:
# Simple case: WPA-PSK, PSK as an ASCII passphrase, allow all valid ciphers
OSDN Git Service
