OSDN Git Service
Bluetooth: Check state in l2cap_disconnect_rsp
Because of both sides doing L2CAP disconnection at the same time, it
was possible to receive L2CAP Disconnection Response with CID that was
already freed. That caused problems if CID was already reused and L2CAP
Connection Request with same CID was sent out. Before this patch kernel
deleted channel context regardless of the state of the channel.
Example where leftover Disconnection Response (frame #402) causes local
device to delete L2CAP channel which was not yet connected. This in
turn confuses remote device's stack because same CID is re-used without
properly disconnecting.
Btmon capture before patch:
** snip **
> ACL Data RX: Handle 43 flags 0x02 dlen 8 #394 [hci1] 10.748949
Channel: 65 len 4 [PSM 3 mode 0] {chan 2}
RFCOMM: Disconnect (DISC) (0x43)
Address: 0x03 cr 1 dlci 0x00
Control: 0x53 poll/final 1
Length: 0
FCS: 0xfd
< ACL Data TX: Handle 43 flags 0x00 dlen 8 #395 [hci1] 10.749062
Channel: 65 len 4 [PSM 3 mode 0] {chan 2}
RFCOMM: Unnumbered Ack (UA) (0x63)
Address: 0x03 cr 1 dlci 0x00
Control: 0x73 poll/final 1
Length: 0
FCS: 0xd7
< ACL Data TX: Handle 43 flags 0x00 dlen 12 #396 [hci1] 10.749073
L2CAP: Disconnection Request (0x06) ident 17 len 4
Destination CID: 65
Source CID: 65
> HCI Event: Number of Completed Packets (0x13) plen 5 #397 [hci1] 10.752391
Num handles: 1
Handle: 43
Count: 1
> HCI Event: Number of Completed Packets (0x13) plen 5 #398 [hci1] 10.753394
Num handles: 1
Handle: 43
Count: 1
> ACL Data RX: Handle 43 flags 0x02 dlen 12 #399 [hci1] 10.756499
L2CAP: Disconnection Request (0x06) ident 26 len 4
Destination CID: 65
Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 12 #400 [hci1] 10.756548
L2CAP: Disconnection Response (0x07) ident 26 len 4
Destination CID: 65
Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 12 #401 [hci1] 10.757459
L2CAP: Connection Request (0x02) ident 18 len 4
PSM: 1 (0x0001)
Source CID: 65
> ACL Data RX: Handle 43 flags 0x02 dlen 12 #402 [hci1] 10.759148
L2CAP: Disconnection Response (0x07) ident 17 len 4
Destination CID: 65
Source CID: 65
= bluetoothd: 00:1E:AB:4C:56:54: error updating services: Input/o.. 10.759447
> HCI Event: Number of Completed Packets (0x13) plen 5 #403 [hci1] 10.759386
Num handles: 1
Handle: 43
Count: 1
> ACL Data RX: Handle 43 flags 0x02 dlen 12 #404 [hci1] 10.760397
L2CAP: Connection Request (0x02) ident 27 len 4
PSM: 3 (0x0003)
Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 16 #405 [hci1] 10.760441
L2CAP: Connection Response (0x03) ident 27 len 8
Destination CID: 65
Source CID: 65
Result: Connection successful (0x0000)
Status: No further information available (0x0000)
< ACL Data TX: Handle 43 flags 0x00 dlen 27 #406 [hci1] 10.760449
L2CAP: Configure Request (0x04) ident 19 len 19
Destination CID: 65
Flags: 0x0000
Option: Maximum Transmission Unit (0x01) [mandatory]
MTU: 1013
Option: Retransmission and Flow Control (0x04) [mandatory]
Mode: Basic (0x00)
TX window size: 0
Max transmit: 0
Retransmission timeout: 0
Monitor timeout: 0
Maximum PDU size: 0
> HCI Event: Number of Completed Packets (0x13) plen 5 #407 [hci1] 10.761399
Num handles: 1
Handle: 43
Count: 1
> ACL Data RX: Handle 43 flags 0x02 dlen 16 #408 [hci1] 10.762942
L2CAP: Connection Response (0x03) ident 18 len 8
Destination CID: 66
Source CID: 65
Result: Connection successful (0x0000)
Status: No further information available (0x0000)
*snip*
Similar case after the patch:
*snip*
> ACL Data RX: Handle 43 flags 0x02 dlen 8 #22702 [hci0] 1664.411056
Channel: 65 len 4 [PSM 3 mode 0] {chan 3}
RFCOMM: Disconnect (DISC) (0x43)
Address: 0x03 cr 1 dlci 0x00
Control: 0x53 poll/final 1
Length: 0
FCS: 0xfd
< ACL Data TX: Handle 43 flags 0x00 dlen 8 #22703 [hci0] 1664.411136
Channel: 65 len 4 [PSM 3 mode 0] {chan 3}
RFCOMM: Unnumbered Ack (UA) (0x63)
Address: 0x03 cr 1 dlci 0x00
Control: 0x73 poll/final 1
Length: 0
FCS: 0xd7
< ACL Data TX: Handle 43 flags 0x00 dlen 12 #22704 [hci0] 1664.411143
L2CAP: Disconnection Request (0x06) ident 11 len 4
Destination CID: 65
Source CID: 65
> HCI Event: Number of Completed Pac.. (0x13) plen 5 #22705 [hci0] 1664.414009
Num handles: 1
Handle: 43
Count: 1
> HCI Event: Number of Completed Pac.. (0x13) plen 5 #22706 [hci0] 1664.415007
Num handles: 1
Handle: 43
Count: 1
> ACL Data RX: Handle 43 flags 0x02 dlen 12 #22707 [hci0] 1664.418674
L2CAP: Disconnection Request (0x06) ident 17 len 4
Destination CID: 65
Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 12 #22708 [hci0] 1664.418762
L2CAP: Disconnection Response (0x07) ident 17 len 4
Destination CID: 65
Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 12 #22709 [hci0] 1664.421073
L2CAP: Connection Request (0x02) ident 12 len 4
PSM: 1 (0x0001)
Source CID: 65
> ACL Data RX: Handle 43 flags 0x02 dlen 12 #22710 [hci0] 1664.421371
L2CAP: Disconnection Response (0x07) ident 11 len 4
Destination CID: 65
Source CID: 65
> HCI Event: Number of Completed Pac.. (0x13) plen 5 #22711 [hci0] 1664.424082
Num handles: 1
Handle: 43
Count: 1
> HCI Event: Number of Completed Pac.. (0x13) plen 5 #22712 [hci0] 1664.425040
Num handles: 1
Handle: 43
Count: 1
> ACL Data RX: Handle 43 flags 0x02 dlen 12 #22713 [hci0] 1664.426103
L2CAP: Connection Request (0x02) ident 18 len 4
PSM: 3 (0x0003)
Source CID: 65
< ACL Data TX: Handle 43 flags 0x00 dlen 16 #22714 [hci0] 1664.426186
L2CAP: Connection Response (0x03) ident 18 len 8
Destination CID: 66
Source CID: 65
Result: Connection successful (0x0000)
Status: No further information available (0x0000)
< ACL Data TX: Handle 43 flags 0x00 dlen 27 #22715 [hci0] 1664.426196
L2CAP: Configure Request (0x04) ident 13 len 19
Destination CID: 65
Flags: 0x0000
Option: Maximum Transmission Unit (0x01) [mandatory]
MTU: 1013
Option: Retransmission and Flow Control (0x04) [mandatory]
Mode: Basic (0x00)
TX window size: 0
Max transmit: 0
Retransmission timeout: 0
Monitor timeout: 0
Maximum PDU size: 0
> ACL Data RX: Handle 43 flags 0x02 dlen 16 #22716 [hci0] 1664.428804
L2CAP: Connection Response (0x03) ident 12 len 8
Destination CID: 66
Source CID: 65
Result: Connection successful (0x0000)
Status: No further information available (0x0000)
*snip*
Fix is to check that channel is in state BT_DISCONN before deleting the
channel.
This bug was found while fuzzing Bluez's OBEX implementation using
Synopsys Defensics.
Reported-by: Matti Kamunen <matti.kamunen@synopsys.com>
Reported-by: Ari Timonen <ari.timonen@synopsys.com>
Signed-off-by: Matias Karhumaa <matias.karhumaa@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>