OSDN Git Service
Merge branch 'Convert-Felix-DSA-switch-to-PHYLINK'
Vladimir Oltean says:
====================
Convert Felix DSA switch to PHYLINK
Unlike most other conversions, this one is not by far a trivial one, and should
be seen as "Layerscape PCS meets PHYLINK". Actually, the PCS doesn't
need a lot of hand-holding and most of our other devices 'just work'
(this one included) without any sort of operating system awareness, just
an initialization procedure done typically in the bootloader.
Our issues start when the PCS stops from "just working", and that is
where PHYLINK comes in handy.
The PCS is not specific to the Vitesse / Microsemi / Microchip switching core
at all. Variations of this SerDes/PCS design can also be found on DPAA1 and
DPAA2 hardware.
The main idea of the abstraction provided is that the PCS looks so much like a
PHY device, that we model it as an actual PHY device and run the generic PHY
functions on it, where appropriate.
The 4xSGMII, QSGMII and QSXGMII modes are fairly straightforward.
The SerDes protocol which the driver calls 2500Base-X mode (a misnomer) is more
interesting. There is a description of how it works and what can be done with
it in patch 9/9 (in a comment above vsc9959_pcs_init_2500basex).
In short, it is a fixed speed protocol with no auto-negotiation whatsoever.
From my research of the SGMII-2500 patent [1], it has nothing to do with
SGMII-2500. That one:
* does not define any change to the AN base page compared to plain 10/100/1000
SGMII. This implies that the 2500 speed is not negotiable, but the other
speeds are. In our case, when the SerDes is configured for this protocol it's
configured for good, there's no going back to SGMII.
* runs at a higher base frequency than regular SGMII. So SGMII-2500 operating
at 1000 Mbps wouldn't interoperate with plain SGMII at 1000 Mbps. Strange,
but ok..
* Emulates lower link speeds than 2500 by duplicating the codewords twice, then
thrice, then twice again etc (2.5/25/250 times on average). The Layerscape
PCS doesn't do that (it is fixed at 2500 Mbaud).
But on the other hand it isn't completely compatible with Base-X either,
since it doesn't do 802.3z / clause 37 auto negotiation (flow control,
local/remote fault etc). It is compatible with 2500Base-X without
in-band AN, and that is exactly how we decided to expose it (this is
actually similar to what others do).
For SGMII and USXGMII, the driver is using the PHYLINK 'managed =
"in-band-status"' DTS binding to figure out whether in-band AN is
expected to be enabled in the PCS or not. It is expected that the
attached PHY follows suite, but there is a gap here: the PHY driver does
not react to this setting, so only one of "AN on" and "AN off" works on
any particular PHY, even though that PHY might support bypassing the
SGMII AN process, as is the case on the VSC8514 PHY present on the
LS1028A-RDB board. A separate series will be sent to propose a way to
deal with that.
I dropped the Ocelot PHYLINK conversion because:
* I don't have VSC7514 hardware anyway
* The hardware is so different in this regard that there's almost nothing to
share anyway.
Changes in v5:
- Added the register write to DEV_CLOCK_CFG back in
felix_phylink_mac_config in patch 9/9.
Changes in v4:
- This is mostly a resend of v3, with the only notable change that I've
dropped the PHY core patches for in_band_autoneg and I'll propose them
independently.
v1 series:
https://www.spinics.net/lists/netdev/msg613869.html
RFC v2 series:
https://www.spinics.net/lists/netdev/msg620128.html
v3 series:
https://www.spinics.net/lists/netdev/msg622060.html
v4 series:
https://www.spinics.net/lists/netdev/msg622606.html
[0]: https://www.spinics.net/lists/netdev/msg613869.html
[1]: https://patents.google.com/patent/US7356047B1/en
====================
Signed-off-by: David S. Miller <davem@davemloft.net>