[POWERPC] CPM_UART: Fix non-console initialisation

The cpm_uart driver is initialised incorrectly, if there is a frame buffer
console, and CONFIG_SERIAL_CPM_CONSOLE is defined. The driver fails to
call cpm_uart_init_portdesc() and set_lineif() in this case.

Signed-off-by: Kalle Pokki <kalle.pokki@iki.fi>
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

diff --git a/drivers/serial/cpm_uart/cpm_uart.h b/drivers/serial/cpm_uart/cpm_uart.h
index a8f894c..69715e5 100644 (file)
--- a/drivers/serial/cpm_uart/cpm_uart.h
+++ b/drivers/serial/cpm_uart/cpm_uart.h
@@ -88,7 +88,7 @@ extern struct uart_cpm_port cpm_uart_ports[UART_NR];
 
 /* these are located in their respective files */
 void cpm_line_cr_cmd(int line, int cmd);
-int cpm_uart_init_portdesc(void);
+int __init cpm_uart_init_portdesc(void);
 int cpm_uart_allocbuf(struct uart_cpm_port *pinfo, unsigned int is_con);
 void cpm_uart_freebuf(struct uart_cpm_port *pinfo);
 

diff --git a/drivers/serial/cpm_uart/cpm_uart_core.c b/drivers/serial/cpm_uart/cpm_uart_core.c
index 32fd8c8..7a3b97f 100644 (file)
--- a/drivers/serial/cpm_uart/cpm_uart_core.c
+++ b/drivers/serial/cpm_uart/cpm_uart_core.c
@@ -1349,11 +1349,10 @@ static int cpm_uart_init(void) {
                pr_info("cpm_uart: WARNING: no UART devices found on platform bus!\n");
                pr_info(
                "cpm_uart: the driver will guess configuration, but this mode is no longer supported.\n");
-#ifndef CONFIG_SERIAL_CPM_CONSOLE
-               ret = cpm_uart_init_portdesc();
-               if (ret)
-                       return ret;
-#endif
+
+               /* Don't run this again, if the console driver did it already */
+               if (cpm_uart_nr == 0)
+                       cpm_uart_init_portdesc();
 
                cpm_reg.nr = cpm_uart_nr;
                ret = uart_register_driver(&cpm_reg);
@@ -1365,6 +1364,8 @@ static int cpm_uart_init(void) {
                        int con = cpm_uart_port_map[i];
                        cpm_uart_ports[con].port.line = i;
                        cpm_uart_ports[con].port.flags = UPF_BOOT_AUTOCONF;
+                       if (cpm_uart_ports[con].set_lineif)
+                               cpm_uart_ports[con].set_lineif(&cpm_uart_ports[con]);
                        uart_add_one_port(&cpm_reg, &cpm_uart_ports[con].port);
                }
 

diff --git a/drivers/serial/cpm_uart/cpm_uart_cpm1.c b/drivers/serial/cpm_uart/cpm_uart_cpm1.c
index 95afc37..08e55fd 100644 (file)
--- a/drivers/serial/cpm_uart/cpm_uart_cpm1.c
+++ b/drivers/serial/cpm_uart/cpm_uart_cpm1.c
@@ -184,7 +184,7 @@ void cpm_uart_freebuf(struct uart_cpm_port *pinfo)
 }
 
 /* Setup any dynamic params in the uart desc */
-int cpm_uart_init_portdesc(void)
+int __init cpm_uart_init_portdesc(void)
 {
        pr_debug("CPM uart[-]:init portdesc\n");