net: dsa: sja1105: Always send through management routes in slot 0

I finally found out how the 4 management route slots are supposed to
be used, but.. it's not worth it.

The description from the comment I've just deleted in this commit is
still true: when more than 1 management slot is active at the same time,
the switch will match frames incoming [from the CPU port] on the lowest
numbered management slot that matches the frame's DMAC.

My issue was that one was not supposed to statically assign each port a
slot. Yes, there are 4 slots and also 4 non-CPU ports, but that is a
mere coincidence.

Instead, the switch can be used like this: every management frame gets a
slot at the right of the most recently assigned slot:

Send mgmt frame 1 through S0:    S0 x  x  x
Send mgmt frame 2 through S1:    S0 S1 x  x
Send mgmt frame 3 through S2:    S0 S1 S2 x
Send mgmt frame 4 through S3:    S0 S1 S2 S3

The difference compared to the old usage is that the transmission of
frames 1-4 doesn't need to wait until the completion of the management
route. It is safe to use a slot to the right of the most recently used
one, because by protocol nobody will program a slot to your left and
"steal" your route towards the correct egress port.

So there is a potential throughput benefit here.

But mgmt frame 5 has no more free slot to use, so it has to wait until
_all_ of S0, S1, S2, S3 are full, in order to use S0 again.

And that's actually exactly the problem: I was looking for something
that would bring more predictable transmission latency, but this is
exactly the opposite: 3 out of 4 frames would be transmitted quicker,
but the 4th would draw the short straw and have a worse worst-case
latency than before.

Useless.

Things are made even worse by PTP TX timestamping, which is something I
won't go deeply into here. Suffice to say that the fact there is a
driver-level lock on the SPI bus offsets any potential throughput gains
that parallelism might bring.

So there's no going back to the multi-slot scheme, remove the
"mgmt_slot" variable from sja1105_port and the dummy static assignment
made at probe time.

While passing by, also remove the assignment to casc_port altogether.
Don't pretend that we support cascaded setups.

Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

diff --git a/drivers/net/dsa/sja1105/sja1105_main.c b/drivers/net/dsa/sja1105/sja1105_main.c
index 1da5ac1..79dd965 100644 (file)
--- a/drivers/net/dsa/sja1105/sja1105_main.c
+++ b/drivers/net/dsa/sja1105/sja1105_main.c
@@ -426,14 +426,6 @@ static int sja1105_init_general_params(struct sja1105_private *priv)
                .tpid2 = ETH_P_SJA1105,
        };
        struct sja1105_table *table;
-       int i, k = 0;
-
-       for (i = 0; i < SJA1105_NUM_PORTS; i++) {
-               if (dsa_is_dsa_port(priv->ds, i))
-                       default_general_params.casc_port = i;
-               else if (dsa_is_user_port(priv->ds, i))
-                       priv->ports[i].mgmt_slot = k++;
-       }
 
        table = &priv->static_config.tables[BLK_IDX_GENERAL_PARAMS];
 
@@ -1827,30 +1819,14 @@ static netdev_tx_t sja1105_port_deferred_xmit(struct dsa_switch *ds, int port,
                                              struct sk_buff *skb)
 {
        struct sja1105_private *priv = ds->priv;
-       struct sja1105_port *sp = &priv->ports[port];
-       int slot = sp->mgmt_slot;
        struct sk_buff *clone;
 
-       /* The tragic fact about the switch having 4x2 slots for installing
-        * management routes is that all of them except one are actually
-        * useless.
-        * If 2 slots are simultaneously configured for two BPDUs sent to the
-        * same (multicast) DMAC but on different egress ports, the switch
-        * would confuse them and redirect first frame it receives on the CPU
-        * port towards the port configured on the numerically first slot
-        * (therefore wrong port), then second received frame on second slot
-        * (also wrong port).
-        * So for all practical purposes, there needs to be a lock that
-        * prevents that from happening. The slot used here is utterly useless
-        * (could have simply been 0 just as fine), but we are doing it
-        * nonetheless, in case a smarter idea ever comes up in the future.
-        */
        mutex_lock(&priv->mgmt_lock);
 
        /* The clone, if there, was made by dsa_skb_tx_timestamp */
        clone = DSA_SKB_CB(skb)->clone;
 
-       sja1105_mgmt_xmit(ds, port, slot, skb, !!clone);
+       sja1105_mgmt_xmit(ds, port, 0, skb, !!clone);
 
        if (!clone)
                goto out;

diff --git a/include/linux/dsa/sja1105.h b/include/linux/dsa/sja1105.h
index c0b6a60..317e05b 100644 (file)
--- a/include/linux/dsa/sja1105.h
+++ b/include/linux/dsa/sja1105.h
@@ -56,7 +56,6 @@ struct sja1105_port {
        struct sja1105_tagger_data *data;
        struct dsa_port *dp;
        bool hwts_tx_en;
-       int mgmt_slot;
 };
 
 #endif /* _NET_DSA_SJA1105_H */