--- /dev/null
+What: /sys/block/*/device/sw_activity
+Date: Jun, 2008
+KernelVersion: v2.6.27
+Contact: linux-ide@vger.kernel.org
+Description:
+ (RW) Used by drivers which support software controlled activity
+ LEDs.
+
+ It has the following valid values:
+
+ 0 OFF - the LED is not activated on activity
+ 1 BLINK_ON - the LED blinks on every 10ms when activity is
+ detected.
+ 2 BLINK_OFF - the LED is on when idle, and blinks off
+ every 10ms when activity is detected.
+
+ Note that the user must turn sw_activity OFF it they wish to
+ control the activity LED via the em_message file.
+
+
+What: /sys/block/*/device/unload_heads
+Date: Sep, 2008
+KernelVersion: v2.6.28
+Contact: linux-ide@vger.kernel.org
+Description:
+ (RW) Hard disk shock protection
+
+ Writing an integer value to this file will take the heads of the
+ respective drive off the platter and block all I/O operations
+ for the specified number of milliseconds.
+
+ - If the device does not support the unload heads feature,
+ access is denied with -EOPNOTSUPP.
+ - The maximal value accepted for a timeout is 30000
+ milliseconds.
+ - A previously set timeout can be cancelled and disk can resume
+ normal operation immediately by specifying a timeout of 0.
+ - Some hard drives only comply with an earlier version of the
+ ATA standard, but support the unload feature nonetheless.
+ There is no safe way Linux can detect these devices, so this
+ is not enabled by default. If it is known that your device
+ does support the unload feature, then you can tell the kernel
+ to enable it by writing -1. It can be disabled again by
+ writing -2.
+ - Values below -2 are rejected with -EINVAL
+
+ For more information, see
+ Documentation/laptops/disk-shock-protection.txt
+
+
+What: /sys/block/*/device/ncq_prio_enable
+Date: Oct, 2016
+KernelVersion: v4.10
+Contact: linux-ide@vger.kernel.org
+Description:
+ (RW) Write to the file to turn on or off the SATA ncq (native
+ command queueing) support. By default this feature is turned
+ off.
the direct i/o path to physical devices. This setting is
controller wide, affecting all configured logical drives on the
controller. This file is readable and writable.
+
+What: /sys/class/scsi_host/hostX/link_power_management_policy
+Date: Oct, 2007
+KernelVersion: v2.6.24
+Contact: linux-ide@vger.kernel.org
+Description:
+ (RW) This parameter allows the user to read and set the link
+ (interface) power management.
+
+ There are four possible options:
+
+ min_power: Tell the controller to try to make the link use the
+ least possible power when possible. This may sacrifice some
+ performance due to increased latency when coming out of lower
+ power states.
+
+ max_performance: Generally, this means no power management.
+ Tell the controller to have performance be a priority over power
+ management.
+
+ medium_power: Tell the controller to enter a lower power state
+ when possible, but do not enter the lowest power state, thus
+ improving latency over min_power setting.
+
+ med_power_with_dipm: Identical to the existing medium_power
+ setting except that it enables dipm (device initiated power
+ management) on top, which makes it match the Windows IRST (Intel
+ Rapid Storage Technology) driver settings. This setting is also
+ close to min_power, except that:
+ a) It does not use host-initiated slumber mode, but it does
+ allow device-initiated slumber
+ b) It does not enable low power device sleep mode (DevSlp).
+
+What: /sys/class/scsi_host/hostX/em_message
+What: /sys/class/scsi_host/hostX/em_message_type
+Date: Jun, 2008
+KernelVersion: v2.6.27
+Contact: linux-ide@vger.kernel.org
+Description:
+ em_message: (RW) Enclosure management support. For the LED
+ protocol, writes and reads correspond to the LED message format
+ as defined in the AHCI spec.
+
+ The user must turn sw_activity (under /sys/block/*/device/) OFF
+ it they wish to control the activity LED via the em_message
+ file.
+
+ em_message_type: (RO) Displays the current enclosure management
+ protocol that is being used by the driver (for eg. LED, SAF-TE,
+ SES-2, SGPIO etc).
+
+What: /sys/class/scsi_host/hostX/ahci_port_cmd
+What: /sys/class/scsi_host/hostX/ahci_host_caps
+What: /sys/class/scsi_host/hostX/ahci_host_cap2
+Date: Mar, 2010
+KernelVersion: v2.6.35
+Contact: linux-ide@vger.kernel.org
+Description:
+ [to be documented]
+
+What: /sys/class/scsi_host/hostX/ahci_host_version
+Date: Mar, 2010
+KernelVersion: v2.6.35
+Contact: linux-ide@vger.kernel.org
+Description:
+ (RO) Display the version of the AHCI spec implemented by the
+ host.
+
+What: /sys/class/scsi_host/hostX/em_buffer
+Date: Apr, 2010
+KernelVersion: v2.6.35
+Contact: linux-ide@vger.kernel.org
+Description:
+ (RW) Allows access to AHCI EM (enclosure management) buffer
+ directly if the host supports EM.
+
+ For eg. the AHCI driver supports SGPIO EM messages but the
+ SATA/AHCI specs do not define the SGPIO message format of the EM
+ buffer. Different hardware(HW) vendors may have different
+ definitions. With the em_buffer attribute, this issue can be
+ solved by allowing HW vendors to provide userland drivers and
+ tools for their SGPIO initiators.
+
+What: /sys/class/scsi_host/hostX/em_message_supported
+Date: Oct, 2009
+KernelVersion: v2.6.39
+Contact: linux-ide@vger.kernel.org
+Description:
+ (RO) Displays supported enclosure management message types.
OSDN Git Service
