rtl8xxxu: Remove unused 8723bu path B IQ calibration code

The 8723bu is a combo WiFi/BT dongle, and path B is not used for WiFi,
so no point in calibrating it.

Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

diff --git a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
index 71d375c..c355d27 100644 (file)
--- a/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
+++ b/drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu.c
@@ -4988,50 +4988,6 @@ out:
        return result;
 }
 
-#ifdef RTL8723BU_PATH_B
-static int rtl8723bu_iqk_path_b(struct rtl8xxxu_priv *priv)
-{
-       u32 reg_eac, reg_eb4, reg_ebc, reg_ec4, reg_ecc, path_sel;
-       int result = 0;
-
-       path_sel = rtl8xxxu_read32(priv, REG_S0S1_PATH_SWITCH);
-
-       val32 = rtl8xxxu_read32(priv, REG_FPGA0_IQK);
-       val32 &= 0x000000ff;
-       rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32);
-
-       /* One shot, path B LOK & IQK */
-       rtl8xxxu_write32(priv, REG_IQK_AGC_CONT, 0x00000002);
-       rtl8xxxu_write32(priv, REG_IQK_AGC_CONT, 0x00000000);
-
-       mdelay(1);
-
-       /* Check failed */
-       reg_eac = rtl8xxxu_read32(priv, REG_RX_POWER_AFTER_IQK_A_2);
-       reg_eb4 = rtl8xxxu_read32(priv, REG_TX_POWER_BEFORE_IQK_B);
-       reg_ebc = rtl8xxxu_read32(priv, REG_TX_POWER_AFTER_IQK_B);
-       reg_ec4 = rtl8xxxu_read32(priv, REG_RX_POWER_BEFORE_IQK_B_2);
-       reg_ecc = rtl8xxxu_read32(priv, REG_RX_POWER_AFTER_IQK_B_2);
-
-       if (!(reg_eac & BIT(31)) &&
-           ((reg_eb4 & 0x03ff0000) != 0x01420000) &&
-           ((reg_ebc & 0x03ff0000) != 0x00420000))
-               result |= 0x01;
-       else
-               goto out;
-
-       if (!(reg_eac & BIT(30)) &&
-           (((reg_ec4 & 0x03ff0000) >> 16) != 0x132) &&
-           (((reg_ecc & 0x03ff0000) >> 16) != 0x36))
-               result |= 0x02;
-       else
-               dev_warn(&priv->udev->dev, "%s: Path B RX IQK failed!\n",
-                        __func__);
-out:
-       return result;
-}
-#endif
-
 static int rtl8192eu_iqk_path_a(struct rtl8xxxu_priv *priv)
 {
        u32 reg_eac, reg_e94, reg_e9c;
@@ -5619,20 +5575,6 @@ static void rtl8723bu_phy_iqcalibrate(struct rtl8xxxu_priv *priv,
        rtl8xxxu_write32(priv, REG_OFDM0_TR_MUX_PAR, 0x000800e4);
        rtl8xxxu_write32(priv, REG_FPGA0_XCD_RF_SW_CTRL, 0x22204000);
 
-#ifdef RTL8723BU_PATH_B
-       /* Set RF mode to standby Path B */
-       if (priv->tx_paths > 1)
-               rtl8xxxu_write_rfreg(priv, RF_B, RF6052_REG_AC, 0x10000);
-#endif
-
-#if 0
-       /* Page B init */
-       rtl8xxxu_write32(priv, REG_CONFIG_ANT_A, 0x0f600000);
-
-       if (priv->tx_paths > 1)
-               rtl8xxxu_write32(priv, REG_CONFIG_ANT_B, 0x0f600000);
-#endif
-
        /*
         * RX IQ calibration setting for 8723B D cut large current issue
         * when leaving IPS
@@ -5662,12 +5604,6 @@ static void rtl8723bu_phy_iqcalibrate(struct rtl8xxxu_priv *priv,
                        val32 &= 0x000000ff;
                        rtl8xxxu_write32(priv, REG_FPGA0_IQK, val32);
 
-#if 0 /* Only needed in restore case, we may need this when going to suspend */
-                       priv->RFCalibrateInfo.TxLOK[RF_A] =
-                               rtl8xxxu_read_rfreg(priv, RF_A,
-                                                   RF6052_REG_TXM_IDAC);
-#endif
-
                        val32 = rtl8xxxu_read32(priv,
                                                REG_TX_POWER_BEFORE_IQK_A);
                        result[t][0] = (val32 >> 16) & 0x3ff;
@@ -6209,15 +6145,9 @@ static void rtl8723bu_phy_iq_calibrate(struct rtl8xxxu_priv *priv)
        rtl8xxxu_write_rfreg(priv, RF_A, RF6052_REG_UNKNOWN_ED, val32);
        rtl8xxxu_write_rfreg(priv, RF_A, 0x43, 0x300bd);
 
-       if (priv->rf_paths > 1) {
-               dev_dbg(dev, "%s: beware 2T not yet supported\n", __func__);
-#ifdef RTL8723BU_PATH_B
-               if (RF_Path == 0x0)     //S1
-                       ODM_SetIQCbyRFpath(pDM_Odm, 0);
-               else    //S0
-                       ODM_SetIQCbyRFpath(pDM_Odm, 1);
-#endif
-       }
+       if (priv->rf_paths > 1)
+               dev_dbg(dev, "%s: 8723BU 2T not supported\n", __func__);
+
        rtl8xxxu_prepare_calibrate(priv, 0);
 }