#define IF_MCONT_TX (IF_MCONT_TXIE | IF_MCONT_EOB)
-/*
- * Use IF1 for RX and IF2 for TX
- */
+/* Use IF1 for RX and IF2 for TX */
#define IF_RX 0
#define IF_TX 1
LEC_MASK = LEC_UNUSED,
};
-/*
- * c_can error types:
+/* c_can error types:
* Bus errors (BUS_OFF, ERROR_WARNING, ERROR_PASSIVE) are supported
*/
enum c_can_bus_error_types {
c_can_obj_update(dev, iface, cmd | IF_COMM_WR, obj);
}
-/*
- * Note: According to documentation clearing TXIE while MSGVAL is set
+/* Note: According to documentation clearing TXIE while MSGVAL is set
* is not allowed, but works nicely on C/DCAN. And that lowers the I/O
* load significantly.
*/
if (!rtr)
arb |= IF_ARB_TRANSMIT;
- /*
- * If we change the DIR bit, we need to invalidate the buffer
+ /* If we change the DIR bit, we need to invalidate the buffer
* first, i.e. clear the MSGVAL flag in the arbiter.
*/
if (rtr != (bool)test_bit(idx, &priv->tx_dir)) {
if (can_dropped_invalid_skb(dev, skb))
return NETDEV_TX_OK;
- /*
- * This is not a FIFO. C/D_CAN sends out the buffers
+ /* This is not a FIFO. C/D_CAN sends out the buffers
* prioritized. The lowest buffer number wins.
*/
idx = fls(atomic_read(&priv->tx_active));
/* If this is the last buffer, stop the xmit queue */
if (idx == C_CAN_MSG_OBJ_TX_NUM - 1)
netif_stop_queue(dev);
- /*
- * Store the message in the interface so we can call
+ /* Store the message in the interface so we can call
* can_put_echo_skb(). We must do this before we enable
* transmit as we might race against do_tx().
*/
return c_can_wait_for_ctrl_init(dev, priv, 0);
}
-/*
- * Configure C_CAN message objects for Tx and Rx purposes:
+/* Configure C_CAN message objects for Tx and Rx purposes:
* C_CAN provides a total of 32 message objects that can be configured
* either for Tx or Rx purposes. Here the first 16 message objects are used as
* a reception FIFO. The end of reception FIFO is signified by the EoB bit
return 0;
}
-/*
- * Configure C_CAN chip:
+/* Configure C_CAN chip:
* - enable/disable auto-retransmission
* - set operating mode
* - configure message objects
}
}
-/*
- * If we have a gap in the pending bits, that means we either
+/* If we have a gap in the pending bits, that means we either
* raced with the hardware or failed to readout all upper
* objects in the last run due to quota limit.
*/
if (pend == RECEIVE_OBJECT_BITS)
return pend;
- /*
- * If the last set bit is larger than the number of pending
+ /* If the last set bit is larger than the number of pending
* bits we have a gap.
*/
weight = hweight32(pend);
if (lasts == weight)
return pend;
- /*
- * Find the first set bit after the gap. We walk backwards
+ /* Find the first set bit after the gap. We walk backwards
* from the last set bit.
*/
for (lasts--; pend & (1 << (lasts - 1)); lasts--);
continue;
}
- /*
- * This really should not happen, but this covers some
+ /* This really should not happen, but this covers some
* odd HW behaviour. Do not remove that unless you
* want to brick your machine.
*/
return pend;
}
-/*
- * theory of operation:
+/* theory of operation:
*
* c_can core saves a received CAN message into the first free message
* object it finds free (starting with the lowest). Bits NEWDAT and
struct c_can_priv *priv = netdev_priv(dev);
u32 pkts = 0, pend = 0, toread, n;
- /*
- * It is faster to read only one 16bit register. This is only possible
+ /* It is faster to read only one 16bit register. This is only possible
* for a maximum number of 16 objects.
*/
BUILD_BUG_ON_MSG(C_CAN_MSG_OBJ_RX_LAST > 16,
pend = c_can_get_pending(priv);
if (!pend)
break;
- /*
- * If the pending field has a gap, handle the
+ /* If the pending field has a gap, handle the
* bits above the gap first.
*/
toread = c_can_adjust_pending(pend);
struct can_frame *cf;
struct sk_buff *skb;
- /*
- * early exit if no lec update or no error.
+ /* early exit if no lec update or no error.
* no lec update means that no CAN bus event has been detected
* since CPU wrote 0x7 value to status reg.
*/
if (unlikely(!skb))
return 0;
- /*
- * check for 'last error code' which tells us the
+ /* check for 'last error code' which tells us the
* type of the last error to occur on the CAN bus
*/
cf->can_id |= CAN_ERR_PROT | CAN_ERR_BUSERROR;
OSDN Git Service
