staging: comedi: pcl818: tidy up pcl818_check()

This function probes a number of the boards registers during the
(*attach) to verify that it is actually a PCL-818 compatible board.
For aesthetics, move the function closer to the (*attach).

Refactor the function to return an errno if fails. Change the errno
from -EIO to -ENODEV and remove the unnecessary comedi_error() noise.

Make sure the CONTROL register is reset to a known state after the
check. The 0x18 value actually defines an invalid interrupt selection
and sets an undefined bit.

Add a couple comments to clarify the magic values.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

diff --git a/drivers/staging/comedi/drivers/pcl818.c b/drivers/staging/comedi/drivers/pcl818.c
index 6510197..56a5de7 100644 (file)
--- a/drivers/staging/comedi/drivers/pcl818.c
+++ b/drivers/staging/comedi/drivers/pcl818.c
@@ -1082,25 +1082,6 @@ end:
        return 0;
 }
 
-static int pcl818_check(unsigned long iobase)
-{
-       outb(0x00, iobase + PCL818_MUX);
-       udelay(1);
-       if (inb(iobase + PCL818_MUX) != 0x00)
-               return 1;       /* there isn't card */
-       outb(0x55, iobase + PCL818_MUX);
-       udelay(1);
-       if (inb(iobase + PCL818_MUX) != 0x55)
-               return 1;       /* there isn't card */
-       outb(0x00, iobase + PCL818_MUX);
-       udelay(1);
-       outb(0x18, iobase + PCL818_CONTROL);
-       udelay(1);
-       if (inb(iobase + PCL818_CONTROL) != 0x18)
-               return 1;       /* there isn't card */
-       return 0;               /*  ok, card exist */
-}
-
 static void pcl818_reset(struct comedi_device *dev)
 {
        const struct pcl818_board *board = comedi_board(dev);
@@ -1187,6 +1168,30 @@ static void pcl818_set_ai_range_table(struct comedi_device *dev,
        }
 }
 
+static int pcl818_check(struct comedi_device *dev)
+{
+       /* the MUX register should return the same value written */
+       outb(0x00, dev->iobase + PCL818_MUX);
+       if (inb(dev->iobase + PCL818_MUX) != 0x00)
+               return -ENODEV;
+       outb(0x55, dev->iobase + PCL818_MUX);
+       if (inb(dev->iobase + PCL818_MUX) != 0x55)
+               return -ENODEV;
+
+       /* reset the MUX register to a known state */
+       outb(0x00, dev->iobase + PCL818_MUX);
+
+       /* the CONTROL register should return the same value written */
+       outb(0x18, dev->iobase + PCL818_CONTROL);
+       if (inb(dev->iobase + PCL818_CONTROL) != 0x18)
+               return -ENODEV;
+
+       /* reset the CONTROL register to a known state */
+       outb(0x00, dev->iobase + PCL818_CONTROL);
+
+       return 0;
+}
+
 static int pcl818_attach(struct comedi_device *dev, struct comedi_devconfig *it)
 {
        const struct pcl818_board *board = comedi_board(dev);
@@ -1208,10 +1213,9 @@ static int pcl818_attach(struct comedi_device *dev, struct comedi_devconfig *it)
        if (ret)
                return ret;
 
-       if (pcl818_check(dev->iobase)) {
-               comedi_error(dev, "I can't detect board. FAIL!\n");
-               return -EIO;
-       }
+       ret = pcl818_check(dev);
+       if (ret)
+               return ret;
 
        /* we can use IRQ 2-7 for async command support */
        if (it->options[1] >= 2 && it->options[1] <= 7) {