aspeed/smc: Wire CS lines at reset

Currently, a set of default flash devices is created at machine init
and drives defined on the QEMU command line are associated to the FMC
and SPI controllers in sequence :

   -drive file<file>,format=raw,if=mtd
   -drive file<file1>,format=raw,if=mtd

The CS lines are wired in the same creation loop. This makes a strong
assumption on the ordering and is not very flexible since only a
limited set of flash devices can be defined : 1 FMC + 1 or 2 SPI,
which is less than what the SoC really supports.

A better alternative would be to define the flash devices on the
command line using a blockdev attached to a CS line of a SSI bus :

    -blockdev node-name=fmc0,driver=file,filename=./flash.img
    -device mx66u51235f,cs=0x0,bus=ssi.0,drive=fmc0

However, user created flash devices are not correctly wired to their
SPI controller and consequently can not be used by the machine. Fix
that and wire the CS lines of all available devices when the SSI bus
is reset.

Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>

diff --git a/hw/arm/aspeed.c b/hw/arm/aspeed.c
index b922a2c..cd92cf9 100644 (file)
--- a/hw/arm/aspeed.c
+++ b/hw/arm/aspeed.c
@@ -307,17 +307,14 @@ void aspeed_board_init_flashes(AspeedSMCState *s, const char *flashtype,
 
     for (i = 0; i < count; ++i) {
         DriveInfo *dinfo = drive_get(IF_MTD, 0, unit0 + i);
-        qemu_irq cs_line;
         DeviceState *dev;
 
         dev = qdev_new(flashtype);
         if (dinfo) {
             qdev_prop_set_drive(dev, "drive", blk_by_legacy_dinfo(dinfo));
         }
+        qdev_prop_set_uint8(dev, "cs", i);
         qdev_realize_and_unref(dev, BUS(s->spi), &error_fatal);
-
-        cs_line = qdev_get_gpio_in_named(dev, SSI_GPIO_CS, 0);
-        qdev_connect_gpio_out_named(DEVICE(s), "cs", i, cs_line);
     }
 }
 

diff --git a/hw/ssi/aspeed_smc.c b/hw/ssi/aspeed_smc.c
index 7281169..2a4001b 100644 (file)
--- a/hw/ssi/aspeed_smc.c
+++ b/hw/ssi/aspeed_smc.c
@@ -692,6 +692,14 @@ static void aspeed_smc_reset(DeviceState *d)
         memset(s->regs, 0, sizeof s->regs);
     }
 
+    for (i = 0; i < asc->cs_num_max; i++) {
+        DeviceState *dev = ssi_get_cs(s->spi, i);
+        if (dev) {
+            qemu_irq cs_line = qdev_get_gpio_in_named(dev, SSI_GPIO_CS, 0);
+            qdev_connect_gpio_out_named(DEVICE(s), "cs", i, cs_line);
+        }
+    }
+
     /* Unselect all peripherals */
     for (i = 0; i < asc->cs_num_max; ++i) {
         s->regs[s->r_ctrl0 + i] |= CTRL_CE_STOP_ACTIVE;