#include <linux/bug.h>
#include <linux/err.h>
#include <linux/gpio.h>
+#include <linux/of_gpio.h>
#include <linux/slab.h>
#include <linux/platform_device.h>
#include <linux/regulator/driver.h>
#define MAX77686_DVS_UVSTEP 12500
/*
+ * Value for configuring buck[89] and LDO{20,21,22} as GPIO control.
+ * It is the same as 'off' for other regulators.
+ */
+#define MAX77686_GPIO_CONTROL 0x0
+/*
* Values used for configuring LDOs and bucks.
* Forcing low power mode: LDO1, 3-5, 9, 13, 17-26
*/
};
struct max77686_data {
+ u64 gpio_enabled:MAX77686_REGULATORS;
+
/* Array indexed by regulator id */
unsigned int opmode[MAX77686_REGULATORS];
};
}
}
+/*
+ * When regulator is configured for GPIO control then it
+ * replaces "normal" mode. Any change from low power mode to normal
+ * should actually change to GPIO control.
+ * Map normal mode to proper value for such regulators.
+ */
+static unsigned int max77686_map_normal_mode(struct max77686_data *max77686,
+ int id)
+{
+ switch (id) {
+ case MAX77686_BUCK8:
+ case MAX77686_BUCK9:
+ case MAX77686_LDO20 ... MAX77686_LDO22:
+ if (max77686->gpio_enabled & (1 << id))
+ return MAX77686_GPIO_CONTROL;
+ }
+
+ return MAX77686_NORMAL;
+}
+
/* Some BUCKs and LDOs supports Normal[ON/OFF] mode during suspend */
static int max77686_set_suspend_disable(struct regulator_dev *rdev)
{
val = MAX77686_LDO_LOWPOWER_PWRREQ;
break;
case REGULATOR_MODE_NORMAL: /* ON in Normal Mode */
- val = MAX77686_NORMAL;
+ val = max77686_map_normal_mode(max77686, id);
break;
default:
pr_warn("%s: regulator_suspend_mode : 0x%x not supported\n",
{
unsigned int val;
struct max77686_data *max77686 = rdev_get_drvdata(rdev);
- int ret;
+ int ret, id = rdev_get_id(rdev);
switch (mode) {
case REGULATOR_MODE_STANDBY: /* switch off */
val = MAX77686_LDO_LOWPOWER_PWRREQ;
break;
case REGULATOR_MODE_NORMAL: /* ON in Normal Mode */
- val = MAX77686_NORMAL;
+ val = max77686_map_normal_mode(max77686, id);
break;
default:
pr_warn("%s: regulator_suspend_mode : 0x%x not supported\n",
if (ret)
return ret;
- max77686->opmode[rdev_get_id(rdev)] = val;
+ max77686->opmode[id] = val;
return 0;
}
shift = max77686_get_opmode_shift(id);
if (max77686->opmode[id] == MAX77686_OFF_PWRREQ)
- max77686->opmode[id] = MAX77686_NORMAL;
+ max77686->opmode[id] = max77686_map_normal_mode(max77686, id);
return regmap_update_bits(rdev->regmap, rdev->desc->enable_reg,
rdev->desc->enable_mask,
MAX77686_RAMP_RATE_MASK, ramp_value << 6);
}
+static int max77686_of_parse_cb(struct device_node *np,
+ const struct regulator_desc *desc,
+ struct regulator_config *config)
+{
+ struct max77686_data *max77686 = config->driver_data;
+
+ switch (desc->id) {
+ case MAX77686_BUCK8:
+ case MAX77686_BUCK9:
+ case MAX77686_LDO20 ... MAX77686_LDO22:
+ config->ena_gpio = of_get_named_gpio(np,
+ "maxim,ena-gpios", 0);
+ config->ena_gpio_flags = GPIOF_OUT_INIT_HIGH;
+ config->ena_gpio_initialized = true;
+ break;
+ default:
+ return 0;
+ }
+
+ if (gpio_is_valid(config->ena_gpio)) {
+ max77686->gpio_enabled |= (1 << desc->id);
+
+ return regmap_update_bits(config->regmap, desc->enable_reg,
+ desc->enable_mask,
+ MAX77686_GPIO_CONTROL);
+ }
+
+ return 0;
+}
+
static struct regulator_ops max77686_ops = {
.list_voltage = regulator_list_voltage_linear,
.map_voltage = regulator_map_voltage_linear,
.name = "LDO"#num, \
.of_match = of_match_ptr("LDO"#num), \
.regulators_node = of_match_ptr("voltage-regulators"), \
+ .of_parse_cb = max77686_of_parse_cb, \
.id = MAX77686_LDO##num, \
.ops = &max77686_ops, \
.type = REGULATOR_VOLTAGE, \
.name = "BUCK"#num, \
.of_match = of_match_ptr("BUCK"#num), \
.regulators_node = of_match_ptr("voltage-regulators"), \
+ .of_parse_cb = max77686_of_parse_cb, \
.id = MAX77686_BUCK##num, \
.ops = &max77686_ops, \
.type = REGULATOR_VOLTAGE, \