staging: most: hdm-dim2: remove macro ENABLE_HDM_TEST

This patch removes the macro ENABLE_HDM_TEST, which was needed while
doing DIM2-HAL simulations. But these are not conducted anymore.

Signed-off-by: Andrey Shvetsov <andrey.shvetsov@k2l.de>
Signed-off-by: Christian Gromm <christian.gromm@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

diff --git a/drivers/staging/most/hdm-dim2/dim2_hdm.c b/drivers/staging/most/hdm-dim2/dim2_hdm.c
index dc71dab..8bef73c 100644 (file)
--- a/drivers/staging/most/hdm-dim2/dim2_hdm.c
+++ b/drivers/staging/most/hdm-dim2/dim2_hdm.c
@@ -55,17 +55,6 @@ static u8 fcnt = 4;  /* (1 << fcnt) frames per subbuffer */
 module_param(fcnt, byte, 0);
 MODULE_PARM_DESC(fcnt, "Num of frames per sub-buffer for sync channels as a power of 2");
 
-/*
- * #############################################################################
- *
- * The define below activates an utility function used by HAL-simu
- * for calling DIM interrupt handler.
- * It is used only for TEST PURPOSE and shall be commented before release.
- *
- * #############################################################################
- */
-/* #define ENABLE_HDM_TEST */
-
 static DEFINE_SPINLOCK(dim_lock);
 
 static void dim2_tasklet_fn(unsigned long data);
@@ -129,10 +118,6 @@ struct dim2_hdm {
        (((p)[1] == 0x18) && ((p)[2] == 0x05) && ((p)[3] == 0x0C) && \
         ((p)[13] == 0x3C) && ((p)[14] == 0x00) && ((p)[15] == 0x0A))
 
-#if defined(ENABLE_HDM_TEST)
-static struct dim2_hdm *test_dev;
-#endif
-
 bool dim2_sysfs_get_state_cb(void)
 {
        bool state;
@@ -467,27 +452,11 @@ static irqreturn_t dim2_ahb_isr(int irq, void *_dev)
        dim_service_irq(get_active_channels(dev, buffer));
        spin_unlock_irqrestore(&dim_lock, flags);
 
-#if !defined(ENABLE_HDM_TEST)
        dim2_tasklet.data = (unsigned long)dev;
        tasklet_schedule(&dim2_tasklet);
-#else
-       dim2_tasklet_fn((unsigned long)dev);
-#endif
        return IRQ_HANDLED;
 }
 
-#if defined(ENABLE_HDM_TEST)
-
-/*
- * Utility function used by HAL-simu for calling DIM interrupt handler.
- * It is used only for TEST PURPOSE.
- */
-void raise_dim_interrupt(void)
-{
-       (void)dim2_ahb_isr(0, test_dev);
-}
-#endif
-
 /**
  * complete_all_mbos - complete MBO's in a list
  * @head: list head
@@ -757,9 +726,6 @@ static int dim2_probe(struct platform_device *pdev)
        dev->atx_idx = -1;
 
        platform_set_drvdata(pdev, dev);
-#if defined(ENABLE_HDM_TEST)
-       test_dev = dev;
-#else
        res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
        dev->io_base = devm_ioremap_resource(&pdev->dev, res);
        if (IS_ERR(dev->io_base))
@@ -779,7 +745,6 @@ static int dim2_probe(struct platform_device *pdev)
                        dev->irq_ahb0, ret);
                return ret;
        }
-#endif
        init_waitqueue_head(&dev->netinfo_waitq);
        dev->deliver_netinfo = 0;
        dev->netinfo_task = kthread_run(&deliver_netinfo_thread, (void *)dev,