/*
- comedi/drivers/ni_atmio.c
- Hardware driver for NI AT-MIO E series cards
-
- COMEDI - Linux Control and Measurement Device Interface
- Copyright (C) 1997-2001 David A. Schleef <ds@schleef.org>
-
- This program is free software; you can redistribute it and/or modify
- it under the terms of the GNU General Public License as published by
- the Free Software Foundation; either version 2 of the License, or
- (at your option) any later version.
-
- This program is distributed in the hope that it will be useful,
- but WITHOUT ANY WARRANTY; without even the implied warranty of
- MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- GNU General Public License for more details.
-*/
-/*
-Driver: ni_atmio
-Description: National Instruments AT-MIO-E series
-Author: ds
-Devices: [National Instruments] AT-MIO-16E-1 (ni_atmio),
- AT-MIO-16E-2, AT-MIO-16E-10, AT-MIO-16DE-10, AT-MIO-64E-3,
- AT-MIO-16XE-50, AT-MIO-16XE-10, AT-AI-16XE-10
-Status: works
-Updated: Thu May 1 20:03:02 CDT 2003
-
-The driver has 2.6 kernel isapnp support, and
-will automatically probe for a supported board if the
-I/O base is left unspecified with comedi_config.
-However, many of
-the isapnp id numbers are unknown. If your board is not
-recognized, please send the output of 'cat /proc/isapnp'
-(you may need to modprobe the isa-pnp module for
-/proc/isapnp to exist) so the
-id numbers for your board can be added to the driver.
-
-Otherwise, you can use the isapnptools package to configure
-your board. Use isapnp to
-configure the I/O base and IRQ for the board, and then pass
-the same values as
-parameters in comedi_config. A sample isapnp.conf file is included
-in the etc/ directory of Comedilib.
-
-Comedilib includes a utility to autocalibrate these boards. The
-boards seem to boot into a state where the all calibration DACs
-are at one extreme of their range, thus the default calibration
-is terrible. Calibration at boot is strongly encouraged.
-
-To use the extended digital I/O on some of the boards, enable the
-8255 driver when configuring the Comedi source tree.
-
-External triggering is supported for some events. The channel index
-(scan_begin_arg, etc.) maps to PFI0 - PFI9.
-
-Some of the more esoteric triggering possibilities of these boards
-are not supported.
-*/
-/*
- The real guts of the driver is in ni_mio_common.c, which is included
- both here and in ni_pcimio.c
-
- Interrupt support added by Truxton Fulton <trux@truxton.com>
-
- References for specifications:
-
- 340747b.pdf Register Level Programmer Manual (obsolete)
- 340747c.pdf Register Level Programmer Manual (new)
- DAQ-STC reference manual
-
- Other possibly relevant info:
-
- 320517c.pdf User manual (obsolete)
- 320517f.pdf User manual (new)
- 320889a.pdf delete
- 320906c.pdf maximum signal ratings
- 321066a.pdf about 16x
- 321791a.pdf discontinuation of at-mio-16e-10 rev. c
- 321808a.pdf about at-mio-16e-10 rev P
- 321837a.pdf discontinuation of at-mio-16de-10 rev d
- 321838a.pdf about at-mio-16de-10 rev N
-
- ISSUES:
-
- need to deal with external reference for DAC, and other DAC
- properties in board properties
+ * Comedi driver for NI AT-MIO E series cards
+ *
+ * COMEDI - Linux Control and Measurement Device Interface
+ * Copyright (C) 1997-2001 David A. Schleef <ds@schleef.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
- deal with at-mio-16de-10 revision D to N changes, etc.
+/*
+ * Driver: ni_atmio
+ * Description: National Instruments AT-MIO-E series
+ * Author: ds
+ * Devices: [National Instruments] AT-MIO-16E-1 (ni_atmio),
+ * AT-MIO-16E-2, AT-MIO-16E-10, AT-MIO-16DE-10, AT-MIO-64E-3,
+ * AT-MIO-16XE-50, AT-MIO-16XE-10, AT-AI-16XE-10
+ * Status: works
+ * Updated: Thu May 1 20:03:02 CDT 2003
+ *
+ * The driver has 2.6 kernel isapnp support, and will automatically probe for
+ * a supported board if the I/O base is left unspecified with comedi_config.
+ * However, many of the isapnp id numbers are unknown. If your board is not
+ * recognized, please send the output of 'cat /proc/isapnp' (you may need to
+ * modprobe the isa-pnp module for /proc/isapnp to exist) so the id numbers
+ * for your board can be added to the driver.
+ *
+ * Otherwise, you can use the isapnptools package to configure your board.
+ * Use isapnp to configure the I/O base and IRQ for the board, and then pass
+ * the same values as parameters in comedi_config. A sample isapnp.conf file
+ * is included in the etc/ directory of Comedilib.
+ *
+ * Comedilib includes a utility to autocalibrate these boards. The boards
+ * seem to boot into a state where the all calibration DACs are at one
+ * extreme of their range, thus the default calibration is terrible.
+ * Calibration at boot is strongly encouraged.
+ *
+ * To use the extended digital I/O on some of the boards, enable the
+ * 8255 driver when configuring the Comedi source tree.
+ *
+ * External triggering is supported for some events. The channel index
+ * (scan_begin_arg, etc.) maps to PFI0 - PFI9.
+ *
+ * Some of the more esoteric triggering possibilities of these boards are
+ * not supported.
+ */
-*/
+/*
+ * The real guts of the driver is in ni_mio_common.c, which is included
+ * both here and in ni_pcimio.c
+ *
+ * Interrupt support added by Truxton Fulton <trux@truxton.com>
+ *
+ * References for specifications:
+ * 340747b.pdf Register Level Programmer Manual (obsolete)
+ * 340747c.pdf Register Level Programmer Manual (new)
+ * DAQ-STC reference manual
+ *
+ * Other possibly relevant info:
+ * 320517c.pdf User manual (obsolete)
+ * 320517f.pdf User manual (new)
+ * 320889a.pdf delete
+ * 320906c.pdf maximum signal ratings
+ * 321066a.pdf about 16x
+ * 321791a.pdf discontinuation of at-mio-16e-10 rev. c
+ * 321808a.pdf about at-mio-16e-10 rev P
+ * 321837a.pdf discontinuation of at-mio-16de-10 rev d
+ * 321838a.pdf about at-mio-16de-10 rev N
+ *
+ * ISSUES:
+ * - need to deal with external reference for DAC, and other DAC
+ * properties in board properties
+ * - deal with at-mio-16de-10 revision D to N changes, etc.
+ */
#include <linux/module.h>
#include <linux/interrupt.h>
OSDN Git Service
