W: http://www.mcuos.com
S: Maintained
+ARM/U300 MACHINE SUPPORT
+M: Linus Walleij <linus.walleij@stericsson.com>
+L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
+S: Supported
+F: arch/arm/mach-u300/
+F: drivers/i2c/busses/i2c-stu300.c
+F: drivers/rtc/rtc-coh901331.c
+F: drivers/watchdog/coh901327_wdt.c
+F: drivers/dma/coh901318*
+
ARM/U8500 ARM ARCHITECTURE
M: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
adr r0, LC0
ARM( ldmia r0, {r1, r2, r3, r4, r5, r6, r11, ip, sp})
THUMB( ldmia r0, {r1, r2, r3, r4, r5, r6, r11, ip} )
- THUMB( ldr sp, [r0, #28] )
+ THUMB( ldr sp, [r0, #32] )
subs r0, r0, r1 @ calculate the delta offset
@ if delta is zero, we are
ldr r3, .saved_pllbr
str r3, [r1, #(AT91_CKGR_PLLBR - AT91_PMC)]
+ tst r3, #(AT91_PMC_MUL & 0xff0000)
+ bne 1f
+ tst r3, #(AT91_PMC_MUL & ~0xff0000)
+ beq 2f
+1:
wait_pllblock
+2:
/* Restore PLLA setting */
ldr r3, .saved_pllar
str r3, [r1, #(AT91_CKGR_PLLAR - AT91_PMC)]
+ tst r3, #(AT91_PMC_MUL & 0xff0000)
+ bne 3f
+ tst r3, #(AT91_PMC_MUL & ~0xff0000)
+ beq 4f
+3:
wait_pllalock
+4:
#ifdef SLOWDOWN_MASTER_CLOCK
/*
int dma_unmap(DMA_MemMap_t *memMap, /* Stores state information about the map */
int dirtied /* non-zero if any of the pages were modified */
) {
+
+ int rc = 0;
int regionIdx;
int segmentIdx;
DMA_Region_t *region;
DMA_Segment_t *segment;
+ down(&memMap->lock);
+
for (regionIdx = 0; regionIdx < memMap->numRegionsUsed; regionIdx++) {
region = &memMap->region[regionIdx];
printk(KERN_ERR
"%s: vmalloc'd pages are not yet supported\n",
__func__);
- return -EINVAL;
+ rc = -EINVAL;
+ goto out;
}
case DMA_MEM_TYPE_KMALLOC:
printk(KERN_ERR
"%s: Unsupported memory type: %d\n",
__func__, region->memType);
- return -EINVAL;
+ rc = -EINVAL;
+ goto out;
}
}
memMap->numRegionsUsed = 0;
memMap->inUse = 0;
+out:
up(&memMap->lock);
- return 0;
+ return rc;
}
EXPORT_SYMBOL(dma_unmap);
#include <mach/hardware.h>
/*************************************************************************
- * GPIO handling for EP93xx
+ * Interrupt handling for EP93xx on-chip GPIOs
*************************************************************************/
static unsigned char gpio_int_unmasked[3];
static unsigned char gpio_int_enabled[3];
static const u8 int_en_register_offset[3] = { 0x9c, 0xb8, 0x58 };
static const u8 int_debounce_register_offset[3] = { 0xa8, 0xc4, 0x64 };
-void ep93xx_gpio_update_int_params(unsigned port)
+static void ep93xx_gpio_update_int_params(unsigned port)
{
BUG_ON(port > 2);
EP93XX_GPIO_REG(int_en_register_offset[port]));
}
-void ep93xx_gpio_int_mask(unsigned line)
+static inline void ep93xx_gpio_int_mask(unsigned line)
{
gpio_int_unmasked[line >> 3] &= ~(1 << (line & 7));
}
Include support for MX31PDK (3DS) platform. This includes specific
configurations for the board and its peripherals.
+config MACH_MX31_3DS_MXC_NAND_USE_BBT
+ bool "Make the MXC NAND driver use the in flash Bad Block Table"
+ depends on MACH_MX31_3DS
+ depends on MTD_NAND_MXC
+ help
+ Enable this if you want that the MXC NAND driver uses the in flash
+ Bad Block Table to know what blocks are bad instead of scanning the
+ entire flash looking for bad block markers.
+
config MACH_MX31MOBOARD
bool "Support mx31moboard platforms (EPFL Mobots group)"
select ARCH_MX31
config MACH_ARMADILLO5X0
bool "Support Atmark Armadillo-500 Development Base Board"
select ARCH_MX31
+ select MXC_ULPI if USB_ULPI
help
Include support for Atmark Armadillo-500 platform. This includes
specific configurations for the board and its peripherals.
}
DEFINE_CLOCK(perclk_clk, 0, NULL, 0, NULL, NULL, &ipg_clk);
+DEFINE_CLOCK(ckil_clk, 0, NULL, 0, clk_ckil_get_rate, NULL, NULL);
DEFINE_CLOCK(sdhc1_clk, 0, MXC_CCM_CGR0, 0, NULL, NULL, &perclk_clk);
DEFINE_CLOCK(sdhc2_clk, 1, MXC_CCM_CGR0, 2, NULL, NULL, &perclk_clk);
DEFINE_CLOCK(mstick1_clk, 0, MXC_CCM_CGR1, 2, mstick1_get_rate, NULL, &usb_pll_clk);
DEFINE_CLOCK(mstick2_clk, 1, MXC_CCM_CGR1, 4, mstick2_get_rate, NULL, &usb_pll_clk);
DEFINE_CLOCK1(csi_clk, 0, MXC_CCM_CGR1, 6, csi, NULL, &serial_pll_clk);
-DEFINE_CLOCK(rtc_clk, 0, MXC_CCM_CGR1, 8, NULL, NULL, &ipg_clk);
+DEFINE_CLOCK(rtc_clk, 0, MXC_CCM_CGR1, 8, NULL, NULL, &ckil_clk);
DEFINE_CLOCK(wdog_clk, 0, MXC_CCM_CGR1, 10, NULL, NULL, &ipg_clk);
DEFINE_CLOCK(pwm_clk, 0, MXC_CCM_CGR1, 12, NULL, NULL, &perclk_clk);
DEFINE_CLOCK(usb_clk2, 0, MXC_CCM_CGR1, 18, usb_get_rate, NULL, &ahb_clk);
DEFINE_CLOCK(nfc_clk, 0, NULL, 0, nfc_get_rate, NULL, &ahb_clk);
DEFINE_CLOCK(scc_clk, 0, NULL, 0, NULL, NULL, &ipg_clk);
DEFINE_CLOCK(ipg_clk, 0, NULL, 0, ipg_get_rate, NULL, &ahb_clk);
-DEFINE_CLOCK(ckil_clk, 0, NULL, 0, clk_ckil_get_rate, NULL, NULL);
#define _REGISTER_CLOCK(d, n, c) \
{ \
_REGISTER_CLOCK(NULL, "iim", iim_clk)
_REGISTER_CLOCK(NULL, "mpeg4", mpeg4_clk)
_REGISTER_CLOCK(NULL, "mbx", mbx_clk)
- _REGISTER_CLOCK("mxc_rtc", NULL, ckil_clk)
};
int __init mx31_clocks_init(unsigned long fref)
.resource = imx_ssi_resources1,
};
-static int mx3_devices_init(void)
+static struct resource imx_wdt_resources[] = {
+ {
+ .flags = IORESOURCE_MEM,
+ },
+};
+
+struct platform_device imx_wdt_device0 = {
+ .name = "imx-wdt",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(imx_wdt_resources),
+ .resource = imx_wdt_resources,
+};
+
+static int __init mx3_devices_init(void)
{
if (cpu_is_mx31()) {
mxc_nand_resources[0].start = MX31_NFC_BASE_ADDR;
mxc_nand_resources[0].end = MX31_NFC_BASE_ADDR + 0xfff;
+ imx_wdt_resources[0].start = MX31_WDOG_BASE_ADDR;
+ imx_wdt_resources[0].end = MX31_WDOG_BASE_ADDR + 0x3fff;
mxc_register_device(&mxc_rnga_device, NULL);
}
if (cpu_is_mx35()) {
imx_ssi_resources0[1].end = MX35_INT_SSI1;
imx_ssi_resources1[1].start = MX35_INT_SSI2;
imx_ssi_resources1[1].end = MX35_INT_SSI2;
+ imx_wdt_resources[0].start = MX35_WDOG_BASE_ADDR;
+ imx_wdt_resources[0].end = MX35_WDOG_BASE_ADDR + 0x3fff;
}
return 0;
extern struct platform_device mxc_spi_device2;
extern struct platform_device imx_ssi_device0;
extern struct platform_device imx_ssi_device1;
-
+extern struct platform_device imx_ssi_device1;
+extern struct platform_device imx_wdt_device0;
#include <linux/input.h>
#include <linux/gpio_keys.h>
#include <linux/i2c.h>
+#include <linux/usb/otg.h>
+#include <linux/usb/ulpi.h>
+#include <linux/delay.h>
#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <mach/ipu.h>
#include <mach/mx3fb.h>
#include <mach/mxc_nand.h>
+#include <mach/mxc_ehci.h>
+#include <mach/ulpi.h>
#include "devices.h"
#include "crm_regs.h"
/* I2C2 */
MX31_PIN_CSPI2_MOSI__SCL,
MX31_PIN_CSPI2_MISO__SDA,
+ /* OTG */
+ MX31_PIN_USBOTG_DATA0__USBOTG_DATA0,
+ MX31_PIN_USBOTG_DATA1__USBOTG_DATA1,
+ MX31_PIN_USBOTG_DATA2__USBOTG_DATA2,
+ MX31_PIN_USBOTG_DATA3__USBOTG_DATA3,
+ MX31_PIN_USBOTG_DATA4__USBOTG_DATA4,
+ MX31_PIN_USBOTG_DATA5__USBOTG_DATA5,
+ MX31_PIN_USBOTG_DATA6__USBOTG_DATA6,
+ MX31_PIN_USBOTG_DATA7__USBOTG_DATA7,
+ MX31_PIN_USBOTG_CLK__USBOTG_CLK,
+ MX31_PIN_USBOTG_DIR__USBOTG_DIR,
+ MX31_PIN_USBOTG_NXT__USBOTG_NXT,
+ MX31_PIN_USBOTG_STP__USBOTG_STP,
+ /* USB host 2 */
+ IOMUX_MODE(MX31_PIN_USBH2_CLK, IOMUX_CONFIG_FUNC),
+ IOMUX_MODE(MX31_PIN_USBH2_DIR, IOMUX_CONFIG_FUNC),
+ IOMUX_MODE(MX31_PIN_USBH2_NXT, IOMUX_CONFIG_FUNC),
+ IOMUX_MODE(MX31_PIN_USBH2_STP, IOMUX_CONFIG_FUNC),
+ IOMUX_MODE(MX31_PIN_USBH2_DATA0, IOMUX_CONFIG_FUNC),
+ IOMUX_MODE(MX31_PIN_USBH2_DATA1, IOMUX_CONFIG_FUNC),
+ IOMUX_MODE(MX31_PIN_STXD3, IOMUX_CONFIG_FUNC),
+ IOMUX_MODE(MX31_PIN_SRXD3, IOMUX_CONFIG_FUNC),
+ IOMUX_MODE(MX31_PIN_SCK3, IOMUX_CONFIG_FUNC),
+ IOMUX_MODE(MX31_PIN_SFS3, IOMUX_CONFIG_FUNC),
+ IOMUX_MODE(MX31_PIN_STXD6, IOMUX_CONFIG_FUNC),
+ IOMUX_MODE(MX31_PIN_SRXD6, IOMUX_CONFIG_FUNC),
};
+/* USB */
+#if defined(CONFIG_USB_ULPI)
+
+#define OTG_RESET IOMUX_TO_GPIO(MX31_PIN_STXD4)
+#define USBH2_RESET IOMUX_TO_GPIO(MX31_PIN_SCK6)
+#define USBH2_CS IOMUX_TO_GPIO(MX31_PIN_GPIO1_3)
+
+#define USB_PAD_CFG (PAD_CTL_DRV_MAX | PAD_CTL_SRE_FAST | PAD_CTL_HYS_CMOS | \
+ PAD_CTL_ODE_CMOS | PAD_CTL_100K_PU)
+
+static int usbotg_init(struct platform_device *pdev)
+{
+ int err;
+
+ mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA0, USB_PAD_CFG);
+ mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA1, USB_PAD_CFG);
+ mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA2, USB_PAD_CFG);
+ mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA3, USB_PAD_CFG);
+ mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA4, USB_PAD_CFG);
+ mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA5, USB_PAD_CFG);
+ mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA6, USB_PAD_CFG);
+ mxc_iomux_set_pad(MX31_PIN_USBOTG_DATA7, USB_PAD_CFG);
+ mxc_iomux_set_pad(MX31_PIN_USBOTG_CLK, USB_PAD_CFG);
+ mxc_iomux_set_pad(MX31_PIN_USBOTG_DIR, USB_PAD_CFG);
+ mxc_iomux_set_pad(MX31_PIN_USBOTG_NXT, USB_PAD_CFG);
+ mxc_iomux_set_pad(MX31_PIN_USBOTG_STP, USB_PAD_CFG);
+
+ /* Chip already enabled by hardware */
+ /* OTG phy reset*/
+ err = gpio_request(OTG_RESET, "USB-OTG-RESET");
+ if (err) {
+ pr_err("Failed to request the usb otg reset gpio\n");
+ return err;
+ }
+
+ err = gpio_direction_output(OTG_RESET, 1/*HIGH*/);
+ if (err) {
+ pr_err("Failed to reset the usb otg phy\n");
+ goto otg_free_reset;
+ }
+
+ gpio_set_value(OTG_RESET, 0/*LOW*/);
+ mdelay(5);
+ gpio_set_value(OTG_RESET, 1/*HIGH*/);
+
+ return 0;
+
+otg_free_reset:
+ gpio_free(OTG_RESET);
+ return err;
+}
+
+static int usbh2_init(struct platform_device *pdev)
+{
+ int err;
+
+ mxc_iomux_set_pad(MX31_PIN_USBH2_CLK, USB_PAD_CFG);
+ mxc_iomux_set_pad(MX31_PIN_USBH2_DIR, USB_PAD_CFG);
+ mxc_iomux_set_pad(MX31_PIN_USBH2_NXT, USB_PAD_CFG);
+ mxc_iomux_set_pad(MX31_PIN_USBH2_STP, USB_PAD_CFG);
+ mxc_iomux_set_pad(MX31_PIN_USBH2_DATA0, USB_PAD_CFG);
+ mxc_iomux_set_pad(MX31_PIN_USBH2_DATA1, USB_PAD_CFG);
+ mxc_iomux_set_pad(MX31_PIN_SRXD6, USB_PAD_CFG);
+ mxc_iomux_set_pad(MX31_PIN_STXD6, USB_PAD_CFG);
+ mxc_iomux_set_pad(MX31_PIN_SFS3, USB_PAD_CFG);
+ mxc_iomux_set_pad(MX31_PIN_SCK3, USB_PAD_CFG);
+ mxc_iomux_set_pad(MX31_PIN_SRXD3, USB_PAD_CFG);
+ mxc_iomux_set_pad(MX31_PIN_STXD3, USB_PAD_CFG);
+
+ mxc_iomux_set_gpr(MUX_PGP_UH2, true);
+
+
+ /* Enable the chip */
+ err = gpio_request(USBH2_CS, "USB-H2-CS");
+ if (err) {
+ pr_err("Failed to request the usb host 2 CS gpio\n");
+ return err;
+ }
+
+ err = gpio_direction_output(USBH2_CS, 0/*Enabled*/);
+ if (err) {
+ pr_err("Failed to drive the usb host 2 CS gpio\n");
+ goto h2_free_cs;
+ }
+
+ /* H2 phy reset*/
+ err = gpio_request(USBH2_RESET, "USB-H2-RESET");
+ if (err) {
+ pr_err("Failed to request the usb host 2 reset gpio\n");
+ goto h2_free_cs;
+ }
+
+ err = gpio_direction_output(USBH2_RESET, 1/*HIGH*/);
+ if (err) {
+ pr_err("Failed to reset the usb host 2 phy\n");
+ goto h2_free_reset;
+ }
+
+ gpio_set_value(USBH2_RESET, 0/*LOW*/);
+ mdelay(5);
+ gpio_set_value(USBH2_RESET, 1/*HIGH*/);
+
+ return 0;
+
+h2_free_reset:
+ gpio_free(USBH2_RESET);
+h2_free_cs:
+ gpio_free(USBH2_CS);
+ return err;
+}
+
+static struct mxc_usbh_platform_data usbotg_pdata = {
+ .init = usbotg_init,
+ .portsc = MXC_EHCI_MODE_ULPI | MXC_EHCI_UTMI_8BIT,
+ .flags = MXC_EHCI_POWER_PINS_ENABLED | MXC_EHCI_INTERFACE_DIFF_UNI,
+};
+
+static struct mxc_usbh_platform_data usbh2_pdata = {
+ .init = usbh2_init,
+ .portsc = MXC_EHCI_MODE_ULPI | MXC_EHCI_UTMI_8BIT,
+ .flags = MXC_EHCI_POWER_PINS_ENABLED | MXC_EHCI_INTERFACE_DIFF_UNI,
+};
+#endif /* CONFIG_USB_ULPI */
+
/* RTC over I2C*/
#define ARMADILLO5X0_RTC_GPIO IOMUX_TO_GPIO(MX31_PIN_SRXD4)
if (armadillo5x0_i2c_rtc.irq == 0)
pr_warning("armadillo5x0_init: failed to get RTC IRQ\n");
i2c_register_board_info(1, &armadillo5x0_i2c_rtc, 1);
+
+ /* USB */
+#if defined(CONFIG_USB_ULPI)
+ usbotg_pdata.otg = otg_ulpi_create(&mxc_ulpi_access_ops,
+ USB_OTG_DRV_VBUS | USB_OTG_DRV_VBUS_EXT);
+ usbh2_pdata.otg = otg_ulpi_create(&mxc_ulpi_access_ops,
+ USB_OTG_DRV_VBUS | USB_OTG_DRV_VBUS_EXT);
+
+ mxc_register_device(&mxc_otg_host, &usbotg_pdata);
+ mxc_register_device(&mxc_usbh2, &usbh2_pdata);
+#endif
}
static void __init armadillo5x0_timer_init(void)
#include <linux/gpio.h>
#include <linux/smsc911x.h>
#include <linux/platform_device.h>
+#include <linux/mfd/mc13783.h>
+#include <linux/spi/spi.h>
+#include <linux/regulator/machine.h>
#include <mach/hardware.h>
#include <asm/mach-types.h>
#include <asm/memory.h>
#include <asm/mach/map.h>
#include <mach/common.h>
-#include <mach/board-mx31pdk.h>
+#include <mach/board-mx31_3ds.h>
#include <mach/imx-uart.h>
#include <mach/iomux-mx3.h>
+#include <mach/mxc_nand.h>
+#include <mach/spi.h>
#include "devices.h"
/*!
- * @file mx31pdk.c
+ * @file mx31_3ds.c
*
* @brief This file contains the board-specific initialization routines.
*
* @ingroup System
*/
-static int mx31pdk_pins[] = {
+static int mx31_3ds_pins[] = {
/* UART1 */
MX31_PIN_CTS1__CTS1,
MX31_PIN_RTS1__RTS1,
MX31_PIN_TXD1__TXD1,
MX31_PIN_RXD1__RXD1,
IOMUX_MODE(MX31_PIN_GPIO1_1, IOMUX_CONFIG_GPIO),
+ /* SPI 1 */
+ MX31_PIN_CSPI2_SCLK__SCLK,
+ MX31_PIN_CSPI2_MOSI__MOSI,
+ MX31_PIN_CSPI2_MISO__MISO,
+ MX31_PIN_CSPI2_SPI_RDY__SPI_RDY,
+ MX31_PIN_CSPI2_SS0__SS0,
+ MX31_PIN_CSPI2_SS2__SS2, /*CS for MC13783 */
+ /* MC13783 IRQ */
+ IOMUX_MODE(MX31_PIN_GPIO1_3, IOMUX_CONFIG_GPIO),
+};
+
+/* Regulators */
+static struct regulator_init_data pwgtx_init = {
+ .constraints = {
+ .boot_on = 1,
+ .always_on = 1,
+ },
+};
+
+static struct mc13783_regulator_init_data mx31_3ds_regulators[] = {
+ {
+ .id = MC13783_REGU_PWGT1SPI, /* Power Gate for ARM core. */
+ .init_data = &pwgtx_init,
+ }, {
+ .id = MC13783_REGU_PWGT2SPI, /* Power Gate for L2 Cache. */
+ .init_data = &pwgtx_init,
+ },
+};
+
+/* MC13783 */
+static struct mc13783_platform_data mc13783_pdata __initdata = {
+ .regulators = mx31_3ds_regulators,
+ .num_regulators = ARRAY_SIZE(mx31_3ds_regulators),
+ .flags = MC13783_USE_REGULATOR,
+};
+
+/* SPI */
+static int spi1_internal_chipselect[] = {
+ MXC_SPI_CS(0),
+ MXC_SPI_CS(2),
+};
+
+static struct spi_imx_master spi1_pdata = {
+ .chipselect = spi1_internal_chipselect,
+ .num_chipselect = ARRAY_SIZE(spi1_internal_chipselect),
+};
+
+static struct spi_board_info mx31_3ds_spi_devs[] __initdata = {
+ {
+ .modalias = "mc13783",
+ .max_speed_hz = 1000000,
+ .bus_num = 1,
+ .chip_select = 1, /* SS2 */
+ .platform_data = &mc13783_pdata,
+ .irq = IOMUX_TO_IRQ(MX31_PIN_GPIO1_3),
+ .mode = SPI_CS_HIGH,
+ },
+};
+
+/*
+ * NAND Flash
+ */
+static struct mxc_nand_platform_data imx31_3ds_nand_flash_pdata = {
+ .width = 1,
+ .hw_ecc = 1,
+#ifdef MACH_MX31_3DS_MXC_NAND_USE_BBT
+ .flash_bbt = 1,
+#endif
};
static struct imxuart_platform_data uart_pdata = {
* LEDs, switches, interrupts for Ethernet.
*/
-static void mx31pdk_expio_irq_handler(uint32_t irq, struct irq_desc *desc)
+static void mx31_3ds_expio_irq_handler(uint32_t irq, struct irq_desc *desc)
{
uint32_t imr_val;
uint32_t int_valid;
.unmask = expio_unmask_irq,
};
-static int __init mx31pdk_init_expio(void)
+static int __init mx31_3ds_init_expio(void)
{
int i;
int ret;
return -ENODEV;
}
- pr_info("i.MX31PDK Debug board detected, rev = 0x%04X\n",
+ pr_info("i.MX31 3DS Debug board detected, rev = 0x%04X\n",
__raw_readw(CPLD_CODE_VER_REG));
/*
set_irq_flags(i, IRQF_VALID);
}
set_irq_type(EXPIO_PARENT_INT, IRQ_TYPE_LEVEL_LOW);
- set_irq_chained_handler(EXPIO_PARENT_INT, mx31pdk_expio_irq_handler);
+ set_irq_chained_handler(EXPIO_PARENT_INT, mx31_3ds_expio_irq_handler);
return 0;
}
/*
* This structure defines the MX31 memory map.
*/
-static struct map_desc mx31pdk_io_desc[] __initdata = {
+static struct map_desc mx31_3ds_io_desc[] __initdata = {
{
.virtual = MX31_CS5_BASE_ADDR_VIRT,
.pfn = __phys_to_pfn(MX31_CS5_BASE_ADDR),
/*
* Set up static virtual mappings.
*/
-static void __init mx31pdk_map_io(void)
+static void __init mx31_3ds_map_io(void)
{
mx31_map_io();
- iotable_init(mx31pdk_io_desc, ARRAY_SIZE(mx31pdk_io_desc));
+ iotable_init(mx31_3ds_io_desc, ARRAY_SIZE(mx31_3ds_io_desc));
}
/*!
*/
static void __init mxc_board_init(void)
{
- mxc_iomux_setup_multiple_pins(mx31pdk_pins, ARRAY_SIZE(mx31pdk_pins),
- "mx31pdk");
+ mxc_iomux_setup_multiple_pins(mx31_3ds_pins, ARRAY_SIZE(mx31_3ds_pins),
+ "mx31_3ds");
mxc_register_device(&mxc_uart_device0, &uart_pdata);
+ mxc_register_device(&mxc_nand_device, &imx31_3ds_nand_flash_pdata);
+
+ mxc_register_device(&mxc_spi_device1, &spi1_pdata);
+ spi_register_board_info(mx31_3ds_spi_devs,
+ ARRAY_SIZE(mx31_3ds_spi_devs));
- if (!mx31pdk_init_expio())
+ if (!mx31_3ds_init_expio())
platform_device_register(&smsc911x_device);
}
-static void __init mx31pdk_timer_init(void)
+static void __init mx31_3ds_timer_init(void)
{
mx31_clocks_init(26000000);
}
-static struct sys_timer mx31pdk_timer = {
- .init = mx31pdk_timer_init,
+static struct sys_timer mx31_3ds_timer = {
+ .init = mx31_3ds_timer_init,
};
/*
* The following uses standard kernel macros defined in arch.h in order to
- * initialize __mach_desc_MX31PDK data structure.
+ * initialize __mach_desc_MX31_3DS data structure.
*/
MACHINE_START(MX31_3DS, "Freescale MX31PDK (3DS)")
/* Maintainer: Freescale Semiconductor, Inc. */
.phys_io = MX31_AIPS1_BASE_ADDR,
.io_pg_offst = (MX31_AIPS1_BASE_ADDR_VIRT >> 18) & 0xfffc,
.boot_params = MX3x_PHYS_OFFSET + 0x100,
- .map_io = mx31pdk_map_io,
+ .map_io = mx31_3ds_map_io,
.init_irq = mx31_init_irq,
.init_machine = mxc_board_init,
- .timer = &mx31pdk_timer,
+ .timer = &mx31_3ds_timer,
MACHINE_END
#include <linux/can/platform/sja1000.h>
#include <linux/usb/otg.h>
#include <linux/usb/ulpi.h>
-#include <linux/fsl_devices.h>
#include <linux/gfp.h>
#include <media/soc_camera.h>
#include <linux/types.h>
#include <linux/init.h>
#include <linux/gpio.h>
-#include <linux/platform_device.h>
#include <linux/leds.h>
#include <linux/platform_device.h>
mxc_register_device(&mxcsdhc_device0, &mmc_pdata);
mxc_register_device(&mxc_spi_device0, &spi0_pdata);
platform_device_register(&litekit_led_device);
+ mxc_register_device(&imx_wdt_device0, NULL);
}
/* GPT */
DEFINE_CLOCK(gpt_clk, 0, MXC_CCM_CCGR2, MXC_CCM_CCGRx_CG9_OFFSET,
- NULL, NULL, &ipg_perclk, NULL);
+ NULL, NULL, &ipg_clk, NULL);
DEFINE_CLOCK(gpt_ipg_clk, 0, MXC_CCM_CCGR2, MXC_CCM_CCGRx_CG10_OFFSET,
NULL, NULL, &ipg_clk, NULL);
#include <linux/types.h>
#include <linux/kernel.h>
#include <linux/init.h>
+#include <linux/module.h>
#include <mach/hardware.h>
#include <asm/io.h>
+static int cpu_silicon_rev = -1;
+
+#define SI_REV 0x48
+
+static void query_silicon_parameter(void)
+{
+ void __iomem *rom = ioremap(MX51_IROM_BASE_ADDR, MX51_IROM_SIZE);
+ u32 rev;
+
+ if (!rom) {
+ cpu_silicon_rev = -EINVAL;
+ return;
+ }
+
+ rev = readl(rom + SI_REV);
+ switch (rev) {
+ case 0x1:
+ cpu_silicon_rev = MX51_CHIP_REV_1_0;
+ break;
+ case 0x2:
+ cpu_silicon_rev = MX51_CHIP_REV_1_1;
+ break;
+ case 0x10:
+ cpu_silicon_rev = MX51_CHIP_REV_2_0;
+ break;
+ case 0x20:
+ cpu_silicon_rev = MX51_CHIP_REV_3_0;
+ break;
+ default:
+ cpu_silicon_rev = 0;
+ }
+
+ iounmap(rom);
+}
+
+/*
+ * Returns:
+ * the silicon revision of the cpu
+ * -EINVAL - not a mx51
+ */
+int mx51_revision(void)
+{
+ if (!cpu_is_mx51())
+ return -EINVAL;
+
+ if (cpu_silicon_rev == -1)
+ query_silicon_parameter();
+
+ return cpu_silicon_rev;
+}
+EXPORT_SYMBOL(mx51_revision);
+
static int __init post_cpu_init(void)
{
unsigned int reg;
.length = MX51_DEBUG_SIZE,
.type = MT_DEVICE
}, {
- .virtual = MX51_TZIC_BASE_ADDR_VIRT,
- .pfn = __phys_to_pfn(MX51_TZIC_BASE_ADDR),
- .length = MX51_TZIC_SIZE,
- .type = MT_DEVICE
- }, {
.virtual = MX51_AIPS1_BASE_ADDR_VIRT,
.pfn = __phys_to_pfn(MX51_AIPS1_BASE_ADDR),
.length = MX51_AIPS1_SIZE,
.pfn = __phys_to_pfn(MX51_AIPS2_BASE_ADDR),
.length = MX51_AIPS2_SIZE,
.type = MT_DEVICE
- }, {
- .virtual = MX51_NFC_AXI_BASE_ADDR_VIRT,
- .pfn = __phys_to_pfn(MX51_NFC_AXI_BASE_ADDR),
- .length = MX51_NFC_AXI_SIZE,
- .type = MT_DEVICE
},
};
*/
void __init mx51_map_io(void)
{
- u32 tzic_addr;
-
- if (mx51_revision() < MX51_CHIP_REV_2_0)
- tzic_addr = 0x8FFFC000;
- else
- tzic_addr = 0xE0003000;
- mxc_io_desc[2].pfn = __phys_to_pfn(tzic_addr);
-
mxc_set_cpu_type(MXC_CPU_MX51);
mxc_iomux_v3_init(MX51_IO_ADDRESS(MX51_IOMUXC_BASE_ADDR));
mxc_arch_reset_init(MX51_IO_ADDRESS(MX51_WDOG_BASE_ADDR));
void __init mx51_init_irq(void)
{
- tzic_init_irq(MX51_IO_ADDRESS(MX51_TZIC_BASE_ADDR));
+ unsigned long tzic_addr;
+ void __iomem *tzic_virt;
+
+ if (mx51_revision() < MX51_CHIP_REV_2_0)
+ tzic_addr = MX51_TZIC_BASE_ADDR_TO1;
+ else
+ tzic_addr = MX51_TZIC_BASE_ADDR;
+
+ tzic_virt = ioremap(tzic_addr, SZ_16K);
+ if (!tzic_virt)
+ panic("unable to map TZIC interrupt controller\n");
+
+ tzic_init_irq(tzic_virt);
}
user_pgprot |= L_PTE_SHARED;
kern_pgprot |= L_PTE_SHARED;
vecs_pgprot |= L_PTE_SHARED;
+ mem_types[MT_DEVICE_WC].prot_sect |= PMD_SECT_S;
+ mem_types[MT_DEVICE_WC].prot_pte |= L_PTE_SHARED;
+ mem_types[MT_DEVICE_CACHED].prot_sect |= PMD_SECT_S;
+ mem_types[MT_DEVICE_CACHED].prot_pte |= L_PTE_SHARED;
mem_types[MT_MEMORY].prot_sect |= PMD_SECT_S;
mem_types[MT_MEMORY_NONCACHED].prot_sect |= PMD_SECT_S;
#endif
* published by the Free Software Foundation.
*/
-#ifndef __ASM_ARCH_MXC_BOARD_MX31PDK_H__
-#define __ASM_ARCH_MXC_BOARD_MX31PDK_H__
+#ifndef __ASM_ARCH_MXC_BOARD_MX31_3DS_H__
+#define __ASM_ARCH_MXC_BOARD_MX31_3DS_H__
/* Definitions for components on the Debug board */
#define MXC_MAX_EXP_IO_LINES 16
-#endif /* __ASM_ARCH_MXC_BOARD_MX31PDK_H__ */
+#endif /* __ASM_ARCH_MXC_BOARD_MX31_3DS_H__ */
* FB100000 70000000 1M SPBA 0
* FB000000 73F00000 1M AIPS 1
* FB200000 83F00000 1M AIPS 2
- * FA100000 8FFFC000 16K TZIC (interrupt controller)
+ * 8FFFC000 16K TZIC (interrupt controller)
* 90000000 256M CSD0 SDRAM/DDR
* A0000000 256M CSD1 SDRAM/DDR
* B0000000 128M CS0 Flash
* C8000000 64M CS3 Flash
* CC000000 32M CS4 SRAM
* CE000000 32M CS5 SRAM
- * F9000000 CFFF0000 64K NFC (NAND Flash AXI)
+ * CFFF0000 64K NFC (NAND Flash AXI)
*
*/
/*
+ * IROM
+ */
+#define MX51_IROM_BASE_ADDR 0x0
+#define MX51_IROM_SIZE SZ_64K
+
+/*
* IRAM
*/
#define MX51_IRAM_BASE_ADDR 0x1FFE0000 /* internal ram */
* NFC
*/
#define MX51_NFC_AXI_BASE_ADDR 0xCFFF0000 /* NAND flash AXI */
-#define MX51_NFC_AXI_BASE_ADDR_VIRT 0xF9000000
#define MX51_NFC_AXI_SIZE SZ_64K
/*
#define MX51_GPU_BASE_ADDR 0x20000000
#define MX51_GPU2D_BASE_ADDR 0xD0000000
-#define MX51_TZIC_BASE_ADDR 0x8FFFC000
-#define MX51_TZIC_BASE_ADDR_VIRT 0xFA100000
-#define MX51_TZIC_SIZE SZ_16K
+#define MX51_TZIC_BASE_ADDR_TO1 0x8FFFC000
+#define MX51_TZIC_BASE_ADDR 0xE0000000
#define MX51_DEBUG_BASE_ADDR 0x60000000
#define MX51_DEBUG_BASE_ADDR_VIRT 0xFA200000
#define MX51_IO_ADDRESS(x) \
(void __iomem *) \
(MX51_IS_MODULE(x, IRAM) ? MX51_IRAM_IO_ADDRESS(x) : \
- MX51_IS_MODULE(x, TZIC) ? MX51_TZIC_IO_ADDRESS(x) : \
MX51_IS_MODULE(x, DEBUG) ? MX51_DEBUG_IO_ADDRESS(x) : \
MX51_IS_MODULE(x, SPBA0) ? MX51_SPBA0_IO_ADDRESS(x) : \
MX51_IS_MODULE(x, AIPS1) ? MX51_AIPS1_IO_ADDRESS(x) : \
- MX51_IS_MODULE(x, AIPS2) ? MX51_AIPS2_IO_ADDRESS(x) : \
- MX51_IS_MODULE(x, NFC_AXI) ? MX51_NFC_AXI_IO_ADDRESS(x) : \
+ MX51_IS_MODULE(x, AIPS2) ? MX51_AIPS2_IO_ADDRESS(x) : \
0xDEADBEEF)
/*
#define MX51_IRAM_IO_ADDRESS(x) \
(((x) - MX51_IRAM_BASE_ADDR) + MX51_IRAM_BASE_ADDR_VIRT)
-#define MX51_TZIC_IO_ADDRESS(x) \
- (((x) - MX51_TZIC_BASE_ADDR) + MX51_TZIC_BASE_ADDR_VIRT)
-
#define MX51_DEBUG_IO_ADDRESS(x) \
(((x) - MX51_DEBUG_BASE_ADDR) + MX51_DEBUG_BASE_ADDR_VIRT)
#define MX51_AIPS2_IO_ADDRESS(x) \
(((x) - MX51_AIPS2_BASE_ADDR) + MX51_AIPS2_BASE_ADDR_VIRT)
-#define MX51_NFC_AXI_IO_ADDRESS(x) \
- (((x) - MX51_NFC_AXI_BASE_ADDR) + MX51_NFC_AXI_BASE_ADDR_VIRT)
-
#define MX51_IS_MEM_DEVICE_NONSHARED(x) 0
/*
#if !defined(__ASSEMBLY__) && !defined(__MXC_BOOT_UNCOMPRESS)
-extern unsigned int system_rev;
-
-static inline unsigned int mx51_revision(void)
-{
- return system_rev;
-}
+extern int mx51_revision(void);
#endif
#endif /* __ASM_ARCH_MXC_MX51_H__ */
#define MX2X_UART1_BASE_ADDR 0x1000a000
#define MX3X_UART1_BASE_ADDR 0x43F90000
#define MX3X_UART2_BASE_ADDR 0x43F94000
+#define MX51_UART1_BASE_ADDR 0x73fbc000
static __inline__ void __arch_decomp_setup(unsigned long arch_id)
{
case MACH_TYPE_MAGX_ZN5:
uart_base = MX3X_UART2_BASE_ADDR;
break;
+ case MACH_TYPE_MX51_BABBAGE:
+ uart_base = MX51_UART1_BASE_ADDR;
+ break;
default:
break;
}