Format: <area>[,<node>]
See also Documentation/networking/decnet.txt.
- default_blu= [VT]
+ vt.default_blu= [VT]
Format: <blue0>,<blue1>,<blue2>,...,<blue15>
Change the default blue palette of the console.
This is a 16-member array composed of values
ranging from 0-255.
- default_grn= [VT]
+ vt.default_grn= [VT]
Format: <green0>,<green1>,<green2>,...,<green15>
Change the default green palette of the console.
This is a 16-member array composed of values
ranging from 0-255.
- default_red= [VT]
+ vt.default_red= [VT]
Format: <red0>,<red1>,<red2>,...,<red15>
Change the default red palette of the console.
This is a 16-member array composed of values
ranging from 0-255.
- default_utf8= [VT]
+ vt.default_utf8=
+ [VT]
Format=<0|1>
Set system-wide default UTF-8 mode for all tty's.
- Default is 0 and by setting to 1, it enables UTF-8
- mode for all newly opened or allocated terminals.
+ Default is 1, i.e. UTF-8 mode is enabled for all
+ newly opened terminals.
dhash_entries= [KNL]
Set number of hash buckets for dentry cache.
lapic_timer_c2_ok [X86-32,x86-64,APIC] trust the local apic timer in
C2 power state.
+ libata.dma= [LIBATA] DMA control
+ libata.dma=0 Disable all PATA and SATA DMA
+ libata.dma=1 PATA and SATA Disk DMA only
+ libata.dma=2 ATAPI (CDROM) DMA only
+ libata.dma=4 Compact Flash DMA only
+ Combinations also work, so libata.dma=3 enables DMA
+ for disks and CDROMs, but not CFs.
+
libata.noacpi [LIBATA] Disables use of ACPI in libata suspend/resume
when set.
Format: <int>
this option.
off or none: don't use autoconfiguration
+ (do static IP assignment instead)
on or any: use any protocol available in the kernel
(default)
dhcp: use DHCP
P: Roland Dreier
M: rolandd@cisco.com
P: Sean Hefty
-M: mshefty@ichips.intel.com
+M: sean.hefty@intel.com
P: Hal Rosenstock
M: hal.rosenstock@gmail.com
L: general@lists.openfabrics.org
S: Maintained
INTEL PRO/100 ETHERNET SUPPORT
-P: John Ronciak
-M: john.ronciak@intel.com
+P: Auke Kok
+M: auke-jan.h.kok@intel.com
P: Jesse Brandeburg
M: jesse.brandeburg@intel.com
P: Jeff Kirsher
M: jeffrey.t.kirsher@intel.com
-P: Auke Kok
-M: auke-jan.h.kok@intel.com
+P: John Ronciak
+M: john.ronciak@intel.com
L: e1000-devel@lists.sourceforge.net
W: http://sourceforge.net/projects/e1000/
S: Supported
INTEL PRO/1000 GIGABIT ETHERNET SUPPORT
-P: Jeb Cramer
-M: cramerj@intel.com
-P: John Ronciak
-M: john.ronciak@intel.com
+P: Auke Kok
+M: auke-jan.h.kok@intel.com
P: Jesse Brandeburg
M: jesse.brandeburg@intel.com
P: Jeff Kirsher
M: jeffrey.t.kirsher@intel.com
-P: Auke Kok
-M: auke-jan.h.kok@intel.com
+P: John Ronciak
+M: john.ronciak@intel.com
L: e1000-devel@lists.sourceforge.net
W: http://sourceforge.net/projects/e1000/
S: Supported
VERSION = 2
PATCHLEVEL = 6
SUBLEVEL = 24
-EXTRAVERSION = -rc6
+EXTRAVERSION = -rc7
NAME = Arr Matey! A Hairy Bilge Rat!
# *DOCUMENTATION*
#endif
};
+static struct i2c_board_info __initdata ek_i2c_devices[] = {
+ {
+ I2C_BOARD_INFO("ics1523", 0x26),
+ },
+ {
+ I2C_BOARD_INFO("dac3550", 0x4d),
+ }
+};
+
#define EK_FLASH_BASE AT91_CHIPSELECT_0
#define EK_FLASH_SIZE 0x200000
SAVE(GAFR1_L); SAVE(GAFR1_U);
SAVE(GAFR2_L); SAVE(GAFR2_U);
- SAVE(ICMR);
+ SAVE(ICMR); ICMR = 0;
SAVE(CKEN);
SAVE(PSTR);
+
+ /* Clear GPIO transition detect bits */
+ GEDR0 = GEDR0; GEDR1 = GEDR1; GEDR2 = GEDR2;
}
static void pxa25x_cpu_pm_restore(unsigned long *sleep_save)
{
+ /* ensure not to come back here if it wasn't intended */
+ PSPR = 0;
+
/* restore registers */
RESTORE_GPLEVEL(0); RESTORE_GPLEVEL(1); RESTORE_GPLEVEL(2);
RESTORE(GPDR0); RESTORE(GPDR1); RESTORE(GPDR2);
RESTORE(GFER0); RESTORE(GFER1); RESTORE(GFER2);
RESTORE(PGSR0); RESTORE(PGSR1); RESTORE(PGSR2);
+ PSSR = PSSR_RDH | PSSR_PH;
+
RESTORE(CKEN);
+
+ ICLR = 0;
+ ICCR = 1;
RESTORE(ICMR);
RESTORE(PSTR);
}
* License. See the file "COPYING" in the main directory of this archive
* for more details.
*
- * Copyright (c) 2004-2005 Silicon Graphics, Inc. All Rights Reserved.
+ * Copyright (c) 2004-2007 Silicon Graphics, Inc. All Rights Reserved.
*/
* PIO read fails, the MCA handler will force the error to look
* corrected and vector to the xp_error_PIOR which will return an error.
*
+ * The definition of "consumption" and the time it takes for an MCA
+ * to surface is processor implementation specific. This code
+ * is sufficient on Itanium through the Montvale processor family.
+ * It may need to be adjusted for future processor implementations.
+ *
* extern int xp_nofault_PIOR(void *remote_register);
*/
mov r8=r0 // Stage a success return value
ld8.acq r9=[r32];; // PIO Read the specified register
adds r9=1,r9;; // Add to force consumption
- or r9=r9,r9;; // Or to force consumption
+ srlz.i;; // Allow time for MCA to surface
br.ret.sptk.many b0;; // Return success
.global xp_error_PIOR
xp_error_PIOR:
mov r8=1 // Return value of 1
br.ret.sptk.many b0;; // Return failure
-
menu "CPU selection"
-source "kernel/time/Kconfig"
-
choice
prompt "CPU type"
default CPU_R4X00
performance should round up your number of processors to the next
power of two.
+source "kernel/time/Kconfig"
+
#
# Timer Interrupt Frequency Configuration
#
/*
* BRIEF MODULE DESCRIPTION
- * Alchemy/AMD Au1x00 pci support.
+ * Alchemy/AMD Au1x00 PCI support.
*
- * Copyright 2001,2002,2003 MontaVista Software Inc.
+ * Copyright 2001-2003, 2007 MontaVista Software Inc.
* Author: MontaVista Software, Inc.
* ppopov@mvista.com or source@mvista.com
*
static int __init au1x_pci_setup(void)
{
+ extern void au1x_pci_cfg_init(void);
+
#if defined(CONFIG_SOC_AU1500) || defined(CONFIG_SOC_AU1550)
virt_io_addr = (unsigned long)ioremap(Au1500_PCI_IO_START,
Au1500_PCI_IO_END - Au1500_PCI_IO_START + 1);
set_io_port_base(virt_io_addr);
#endif
+ au1x_pci_cfg_init();
+
register_pci_controller(&au1x_controller);
return 0;
}
* kernel load address. This is needed because this platform does
* not have a ELF loader yet.
*/
- __INIT
+FEXPORT(__kernel_entry)
+ j kernel_entry
#endif
__INIT_REFOK
return 1;
/*
- * I don't have erratas for newer R4400 so be paranoid.
+ * we assume newer revisions are ok
*/
- return 1;
+ return 0;
}
return 0;
/*
* BRIEF MODULE DESCRIPTION
- * Alchemy/AMD Au1x00 pci support.
+ * Alchemy/AMD Au1x00 PCI support.
*
- * Copyright 2001,2002,2003 MontaVista Software Inc.
+ * Copyright 2001-2003, 2007 MontaVista Software Inc.
* Author: MontaVista Software, Inc.
* ppopov@mvista.com or source@mvista.com
*
write_c0_pagemask(old_pagemask);
}
-struct vm_struct *pci_cfg_vm;
+static struct vm_struct *pci_cfg_vm;
static int pci_cfg_wired_entry;
-static int first_cfg = 1;
-unsigned long last_entryLo0, last_entryLo1;
+static unsigned long last_entryLo0, last_entryLo1;
+
+/*
+ * We can't ioremap the entire pci config space because it's too large.
+ * Nor can we call ioremap dynamically because some device drivers use
+ * the PCI config routines from within interrupt handlers and that
+ * becomes a problem in get_vm_area(). We use one wired TLB to handle
+ * all config accesses for all busses.
+ */
+void __init au1x_pci_cfg_init(void)
+{
+ /* Reserve a wired entry for PCI config accesses */
+ pci_cfg_vm = get_vm_area(0x2000, VM_IOREMAP);
+ if (!pci_cfg_vm)
+ panic(KERN_ERR "PCI unable to get vm area\n");
+ pci_cfg_wired_entry = read_c0_wired();
+ add_wired_entry(0, 0, (unsigned long)pci_cfg_vm->addr, PM_4K);
+ last_entryLo0 = last_entryLo1 = 0xffffffff;
+}
static int config_access(unsigned char access_type, struct pci_bus *bus,
unsigned int dev_fn, unsigned char where,
Au1500_PCI_STATCMD);
au_sync_udelay(1);
- /*
- * We can't ioremap the entire pci config space because it's
- * too large. Nor can we call ioremap dynamically because some
- * device drivers use the pci config routines from within
- * interrupt handlers and that becomes a problem in get_vm_area().
- * We use one wired tlb to handle all config accesses for all
- * busses. To improve performance, if the current device
- * is the same as the last device accessed, we don't touch the
- * tlb.
- */
- if (first_cfg) {
- /* reserve a wired entry for pci config accesses */
- first_cfg = 0;
- pci_cfg_vm = get_vm_area(0x2000, VM_IOREMAP);
- if (!pci_cfg_vm)
- panic(KERN_ERR "PCI unable to get vm area\n");
- pci_cfg_wired_entry = read_c0_wired();
- add_wired_entry(0, 0, (unsigned long)pci_cfg_vm->addr, PM_4K);
- last_entryLo0 = last_entryLo1 = 0xffffffff;
- }
-
/* Allow board vendors to implement their own off-chip idsel.
* If it doesn't succeed, may as well bail out at this point.
*/
/* page boundary */
cfg_base = cfg_base & PAGE_MASK;
+ /*
+ * To improve performance, if the current device is the same as
+ * the last device accessed, we don't touch the TLB.
+ */
entryLo0 = (6 << 26) | (cfg_base >> 6) | (2 << 3) | 7;
entryLo1 = (6 << 26) | (cfg_base >> 6) | (0x1000 >> 6) | (2 << 3) | 7;
-
if ((entryLo0 != last_entryLo0) || (entryLo1 != last_entryLo1)) {
mod_wired_entry(pci_cfg_wired_entry, entryLo0, entryLo1,
(unsigned long)pci_cfg_vm->addr, PM_4K);
mace_pci_read_config(struct pci_bus *bus, unsigned int devfn,
int reg, int size, u32 *val)
{
+ u32 control = mace->pci.control;
+
+ /* disable master aborts interrupts during config read */
+ mace->pci.control = control & ~MACEPCI_CONTROL_MAR_INT;
mace->pci.config_addr = mkaddr(bus, devfn, reg);
switch (size) {
case 1:
*val = mace->pci.config_data.l;
break;
}
+ /* ack possible master abort */
+ mace->pci.error &= ~MACEPCI_ERROR_MASTER_ABORT;
+ mace->pci.control = control;
DPRINTK("read%d: reg=%08x,val=%02x\n", size * 8, reg, *val);
.iommu = 0,
.mem_offset = MACE_PCI_MEM_OFFSET,
.io_offset = 0,
+ .io_map_base = CKSEG1ADDR(MACEPCI_LOW_IO),
};
static int __init mace_init(void)
BUG_ON(request_irq(MACE_PCI_BRIDGE_IRQ, macepci_error, 0,
"MACE PCI error", NULL));
- iomem_resource = mace_pci_mem_resource;
+ /* extend memory resources */
+ iomem_resource.end = mace_pci_mem_resource.end;
ioport_resource = mace_pci_io_resource;
register_pci_controller(&mace_pci_controller);
crime_int = crime->istat & crime_mask;
irq = MACE_VID_IN1_IRQ + __ffs(crime_int);
- crime_int = 1 << irq;
if (crime_int & CRIME_MACEISA_INT_MASK) {
unsigned long mace_int = mace->perif.ctrl.istat;
#include <asm/ip32/mace.h>
#include <asm/ip32/ip32_ints.h>
-/*
- * .iobase isn't a constant (in the sense of C) so we fill it in at runtime.
- */
-#define MACE_PORT(int) \
+#define MACEISA_SERIAL1_OFFS offsetof(struct sgi_mace, isa.serial1)
+#define MACEISA_SERIAL2_OFFS offsetof(struct sgi_mace, isa.serial2)
+
+#define MACE_PORT(offset,_irq) \
{ \
- .irq = int, \
+ .mapbase = MACE_BASE + offset, \
+ .irq = _irq, \
.uartclk = 1843200, \
.iotype = UPIO_MEM, \
- .flags = UPF_SKIP_TEST, \
+ .flags = UPF_SKIP_TEST|UPF_IOREMAP, \
.regshift = 8, \
}
static struct plat_serial8250_port uart8250_data[] = {
- MACE_PORT(MACEISA_SERIAL1_IRQ),
- MACE_PORT(MACEISA_SERIAL2_IRQ),
+ MACE_PORT(MACEISA_SERIAL1_OFFS, MACEISA_SERIAL1_IRQ),
+ MACE_PORT(MACEISA_SERIAL2_OFFS, MACEISA_SERIAL2_IRQ),
{ },
};
static int __init uart8250_init(void)
{
- uart8250_data[0].membase = (void __iomem *) &mace->isa.serial1;
- uart8250_data[1].membase = (void __iomem *) &mace->isa.serial2;
-
return platform_device_register(&uart8250_device);
}
but also at lower core voltage.
endmenu
+
+config OPROFILE_CELL
+ def_bool y
+ depends on PPC_CELL_NATIVE && (OPROFILE = m || OPROFILE = y)
+
spu-manage-$(CONFIG_PPC_CELL_NATIVE) += spu_manage.o
obj-$(CONFIG_SPU_BASE) += spu_callbacks.o spu_base.o \
+ spu_notify.o \
spu_syscalls.o \
$(spu-priv1-y) \
$(spu-manage-y) \
--- /dev/null
+/*
+ * Move OProfile dependencies from spufs module to the kernel so it
+ * can run on non-cell PPC.
+ *
+ * Copyright (C) IBM 2005
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2, or (at your option)
+ * any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#undef DEBUG
+
+#include <linux/module.h>
+#include <asm/spu.h>
+#include "spufs/spufs.h"
+
+static BLOCKING_NOTIFIER_HEAD(spu_switch_notifier);
+
+void spu_switch_notify(struct spu *spu, struct spu_context *ctx)
+{
+ blocking_notifier_call_chain(&spu_switch_notifier,
+ ctx ? ctx->object_id : 0, spu);
+}
+EXPORT_SYMBOL_GPL(spu_switch_notify);
+
+int spu_switch_event_register(struct notifier_block *n)
+{
+ int ret;
+ ret = blocking_notifier_chain_register(&spu_switch_notifier, n);
+ if (!ret)
+ notify_spus_active();
+ return ret;
+}
+EXPORT_SYMBOL_GPL(spu_switch_event_register);
+
+int spu_switch_event_unregister(struct notifier_block *n)
+{
+ return blocking_notifier_chain_unregister(&spu_switch_notifier, n);
+}
+EXPORT_SYMBOL_GPL(spu_switch_event_unregister);
+
+void spu_set_profile_private_kref(struct spu_context *ctx,
+ struct kref *prof_info_kref,
+ void (* prof_info_release) (struct kref *kref))
+{
+ ctx->prof_priv_kref = prof_info_kref;
+ ctx->prof_priv_release = prof_info_release;
+}
+EXPORT_SYMBOL_GPL(spu_set_profile_private_kref);
+
+void *spu_get_profile_private_kref(struct spu_context *ctx)
+{
+ return ctx->prof_priv_kref;
+}
+EXPORT_SYMBOL_GPL(spu_get_profile_private_kref);
+
return ret;
}
+void notify_spus_active(void)
+{
+ struct spufs_calls *calls;
+
+ calls = spufs_calls_get();
+ if (!calls)
+ return;
+
+ calls->notify_spus_active();
+ spufs_calls_put(calls);
+
+ return;
+}
+
int register_spu_syscalls(struct spufs_calls *calls)
{
if (spufs_calls)
spu_release(ctx);
}
-void spu_set_profile_private_kref(struct spu_context *ctx,
- struct kref *prof_info_kref,
- void ( * prof_info_release) (struct kref *kref))
-{
- ctx->prof_priv_kref = prof_info_kref;
- ctx->prof_priv_release = prof_info_release;
-}
-EXPORT_SYMBOL_GPL(spu_set_profile_private_kref);
-
-void *spu_get_profile_private_kref(struct spu_context *ctx)
-{
- return ctx->prof_priv_kref;
-}
-EXPORT_SYMBOL_GPL(spu_get_profile_private_kref);
-
-
return rval;
}
-static BLOCKING_NOTIFIER_HEAD(spu_switch_notifier);
-
-void spu_switch_notify(struct spu *spu, struct spu_context *ctx)
-{
- blocking_notifier_call_chain(&spu_switch_notifier,
- ctx ? ctx->object_id : 0, spu);
-}
-
-static void notify_spus_active(void)
+void do_notify_spus_active(void)
{
int node;
}
}
-int spu_switch_event_register(struct notifier_block * n)
-{
- int ret;
- ret = blocking_notifier_chain_register(&spu_switch_notifier, n);
- if (!ret)
- notify_spus_active();
- return ret;
-}
-EXPORT_SYMBOL_GPL(spu_switch_event_register);
-
-int spu_switch_event_unregister(struct notifier_block * n)
-{
- return blocking_notifier_chain_unregister(&spu_switch_notifier, n);
-}
-EXPORT_SYMBOL_GPL(spu_switch_event_unregister);
-
/**
* spu_bind_context - bind spu context to physical spu
* @spu: physical spu to bind to
.spu_run = do_spu_run,
.coredump_extra_notes_size = spufs_coredump_extra_notes_size,
.coredump_extra_notes_write = spufs_coredump_extra_notes_write,
+ .notify_spus_active = do_notify_spus_active,
.owner = THIS_MODULE,
};
#include <linux/workqueue.h>
#include <linux/fs.h>
#include <linux/syscalls.h>
+#include <linux/ctype.h>
#include <asm/lmb.h>
HEADER_LDR_FORMAT_GZIP = 1,
};
+#define OS_AREA_HEADER_MAGIC_NUM "cell_ext_os_area"
+
/**
* struct os_area_header - os area header segment.
* @magic_num: Always 'cell_ext_os_area'.
u8 _reserved_5[8];
};
-enum {
- OS_AREA_DB_MAGIC_NUM = 0x2d64622dU,
-};
+#define OS_AREA_DB_MAGIC_NUM "-db-"
/**
* struct os_area_db - Shared flash memory database.
- * @magic_num: Always '-db-' = 0x2d64622d.
+ * @magic_num: Always '-db-'.
* @version: os_area_db format version number.
* @index_64: byte offset of the database id index for 64 bit variables.
* @count_64: number of usable 64 bit index entries
*/
struct os_area_db {
- u32 magic_num;
+ u8 magic_num[4];
u16 version;
u16 _reserved_1;
u16 index_64;
prop->name);
}
+static void dump_field(char *s, const u8 *field, int size_of_field)
+{
+#if defined(DEBUG)
+ int i;
+
+ for (i = 0; i < size_of_field; i++)
+ s[i] = isprint(field[i]) ? field[i] : '.';
+ s[i] = 0;
+#endif
+}
+
#define dump_header(_a) _dump_header(_a, __func__, __LINE__)
static void _dump_header(const struct os_area_header *h, const char *func,
int line)
{
+ char str[sizeof(h->magic_num) + 1];
+
+ dump_field(str, h->magic_num, sizeof(h->magic_num));
pr_debug("%s:%d: h.magic_num: '%s'\n", func, line,
- h->magic_num);
+ str);
pr_debug("%s:%d: h.hdr_version: %u\n", func, line,
h->hdr_version);
pr_debug("%s:%d: h.db_area_offset: %u\n", func, line,
static int verify_header(const struct os_area_header *header)
{
- if (memcmp(header->magic_num, "cell_ext_os_area", 16)) {
+ if (memcmp(header->magic_num, OS_AREA_HEADER_MAGIC_NUM,
+ sizeof(header->magic_num))) {
pr_debug("%s:%d magic_num failed\n", __func__, __LINE__);
return -1;
}
static int db_verify(const struct os_area_db *db)
{
- if (db->magic_num != OS_AREA_DB_MAGIC_NUM) {
+ if (memcmp(db->magic_num, OS_AREA_DB_MAGIC_NUM,
+ sizeof(db->magic_num))) {
pr_debug("%s:%d magic_num failed\n", __func__, __LINE__);
return -1;
}
static void _dump_db(const struct os_area_db *db, const char *func,
int line)
{
+ char str[sizeof(db->magic_num) + 1];
+
+ dump_field(str, db->magic_num, sizeof(db->magic_num));
pr_debug("%s:%d: db.magic_num: '%s'\n", func, line,
- (const char*)&db->magic_num);
+ str);
pr_debug("%s:%d: db.version: %u\n", func, line,
db->version);
pr_debug("%s:%d: db.index_64: %u\n", func, line,
memset(db, 0, sizeof(struct os_area_db));
- db->magic_num = OS_AREA_DB_MAGIC_NUM;
+ memcpy(db->magic_num, OS_AREA_DB_MAGIC_NUM, sizeof(db->magic_num));
db->version = 1;
db->index_64 = HEADER_SIZE;
db->count_64 = VALUES_64_COUNT;
apm_info.disabled = 1;
return -ENODEV;
}
- if (PM_IS_ACTIVE()) {
+ if (pm_flags & PM_ACPI) {
printk(KERN_NOTICE "apm: overridden by ACPI.\n");
apm_info.disabled = 1;
return -ENODEV;
}
-#ifdef CONFIG_PM_LEGACY
- pm_active = 1;
-#endif
+ pm_flags |= PM_APM;
/*
* Set up a segment that references the real mode segment 0x40
kthread_stop(kapmd_task);
kapmd_task = NULL;
}
-#ifdef CONFIG_PM_LEGACY
- pm_active = 0;
-#endif
+ pm_flags &= ~PM_APM;
}
module_init(apm_init);
/* Do an early initialization of the fixmap area */
movl $(swapper_pg_dir - __PAGE_OFFSET), %edx
movl $(swapper_pg_pmd - __PAGE_OFFSET), %eax
- addl $0x007, %eax /* 0x007 = PRESENT+RW+USER */
+ addl $0x67, %eax /* 0x67 == _PAGE_TABLE */
movl %eax, 4092(%edx)
xorl %ebx,%ebx /* This is the boot CPU (BSP) */
int cpu;
};
-void do_fork_idle(struct work_struct *work)
+static void __cpuinit do_fork_idle(struct work_struct *work)
{
struct create_idle *c_idle =
container_of(work, struct create_idle, work);
and functions, which do not yet exist in /sys
Say N to delete power /proc/acpi/ folders that have moved to /sys/
+config ACPI_SYSFS_POWER
+ bool "Future power /sys interface"
+ select POWER_SUPPLY
+ default y
+ ---help---
+ Say N to disable power /sys interface
config ACPI_PROC_EVENT
bool "Deprecated /proc/acpi/event support"
depends on PROC_FS
config ACPI_AC
tristate "AC Adapter"
depends on X86
- select POWER_SUPPLY
default y
help
This driver adds support for the AC Adapter object, which indicates
config ACPI_BATTERY
tristate "Battery"
depends on X86
- select POWER_SUPPLY
default y
help
This driver adds support for battery information through
config ACPI_SBS
tristate "Smart Battery System"
depends on X86
- select POWER_SUPPLY
help
This driver adds support for the Smart Battery System, another
type of access to battery information, found on some laptops.
#include <linux/proc_fs.h>
#include <linux/seq_file.h>
#endif
+#ifdef CONFIG_ACPI_SYSFS_POWER
#include <linux/power_supply.h>
+#endif
#include <acpi/acpi_bus.h>
#include <acpi/acpi_drivers.h>
};
struct acpi_ac {
+#ifdef CONFIG_ACPI_SYSFS_POWER
struct power_supply charger;
+#endif
struct acpi_device * device;
unsigned long state;
};
.release = single_release,
};
#endif
-
+#ifdef CONFIG_ACPI_SYSFS_POWER
static int get_ac_property(struct power_supply *psy,
enum power_supply_property psp,
union power_supply_propval *val)
static enum power_supply_property ac_props[] = {
POWER_SUPPLY_PROP_ONLINE,
};
-
+#endif
/* --------------------------------------------------------------------------
AC Adapter Management
-------------------------------------------------------------------------- */
acpi_bus_generate_netlink_event(device->pnp.device_class,
device->dev.bus_id, event,
(u32) ac->state);
+#ifdef CONFIG_ACPI_SYSFS_POWER
kobject_uevent(&ac->charger.dev->kobj, KOBJ_CHANGE);
+#endif
break;
default:
ACPI_DEBUG_PRINT((ACPI_DB_INFO,
#endif
if (result)
goto end;
+#ifdef CONFIG_ACPI_SYSFS_POWER
ac->charger.name = acpi_device_bid(device);
ac->charger.type = POWER_SUPPLY_TYPE_MAINS;
ac->charger.properties = ac_props;
ac->charger.num_properties = ARRAY_SIZE(ac_props);
ac->charger.get_property = get_ac_property;
power_supply_register(&ac->device->dev, &ac->charger);
+#endif
status = acpi_install_notify_handler(device->handle,
ACPI_ALL_NOTIFY, acpi_ac_notify,
ac);
old_state = ac->state;
if (acpi_ac_get_state(ac))
return 0;
+#ifdef CONFIG_ACPI_SYSFS_POWER
if (old_state != ac->state)
kobject_uevent(&ac->charger.dev->kobj, KOBJ_CHANGE);
+#endif
return 0;
}
status = acpi_remove_notify_handler(device->handle,
ACPI_ALL_NOTIFY, acpi_ac_notify);
+#ifdef CONFIG_ACPI_SYSFS_POWER
if (ac->charger.dev)
power_supply_unregister(&ac->charger);
+#endif
#ifdef CONFIG_ACPI_PROCFS_POWER
acpi_ac_remove_fs(device);
#endif
#include <acpi/acpi_bus.h>
#include <acpi/acpi_drivers.h>
+#ifdef CONFIG_ACPI_SYSFS_POWER
#include <linux/power_supply.h>
+#endif
#define ACPI_BATTERY_VALUE_UNKNOWN 0xFFFFFFFF
struct acpi_battery {
struct mutex lock;
+#ifdef CONFIG_ACPI_SYSFS_POWER
struct power_supply bat;
+#endif
struct acpi_device *device;
unsigned long update_time;
int current_now;
return battery->device->status.battery_present;
}
+#ifdef CONFIG_ACPI_SYSFS_POWER
static int acpi_battery_technology(struct acpi_battery *battery)
{
if (!strcasecmp("NiCd", battery->type))
POWER_SUPPLY_PROP_MODEL_NAME,
POWER_SUPPLY_PROP_MANUFACTURER,
};
+#endif
#ifdef CONFIG_ACPI_PROCFS_POWER
inline char *acpi_battery_units(struct acpi_battery *battery)
return acpi_battery_set_alarm(battery);
}
+#ifdef CONFIG_ACPI_SYSFS_POWER
static ssize_t acpi_battery_alarm_show(struct device *dev,
struct device_attribute *attr,
char *buf)
{
int result;
- battery->update_time = 0;
- result = acpi_battery_get_info(battery);
- acpi_battery_init_alarm(battery);
- if (result)
- return result;
if (battery->power_unit) {
battery->bat.properties = charge_battery_props;
battery->bat.num_properties =
power_supply_unregister(&battery->bat);
battery->bat.dev = NULL;
}
+#endif
static int acpi_battery_update(struct acpi_battery *battery)
{
- int result = acpi_battery_get_status(battery);
+ int result;
+ result = acpi_battery_get_status(battery);
if (result)
return result;
+#ifdef CONFIG_ACPI_SYSFS_POWER
if (!acpi_battery_present(battery)) {
sysfs_remove_battery(battery);
+ battery->update_time = 0;
return 0;
}
+#endif
+ if (!battery->update_time) {
+ result = acpi_battery_get_info(battery);
+ if (result)
+ return result;
+ acpi_battery_init_alarm(battery);
+ }
+#ifdef CONFIG_ACPI_SYSFS_POWER
if (!battery->bat.dev)
sysfs_add_battery(battery);
+#endif
return acpi_battery_get_state(battery);
}
acpi_bus_generate_netlink_event(device->pnp.device_class,
device->dev.bus_id, event,
acpi_battery_present(battery));
+#ifdef CONFIG_ACPI_SYSFS_POWER
/* acpi_batter_update could remove power_supply object */
if (battery->bat.dev)
kobject_uevent(&battery->bat.dev->kobj, KOBJ_CHANGE);
+#endif
}
static int acpi_battery_add(struct acpi_device *device)
#ifdef CONFIG_ACPI_PROCFS_POWER
acpi_battery_remove_fs(device);
#endif
+#ifdef CONFIG_ACPI_SYSFS_POWER
sysfs_remove_battery(battery);
+#endif
mutex_destroy(&battery->lock);
kfree(battery);
return 0;
#include <linux/list.h>
#include <linux/sched.h>
#include <linux/pm.h>
-#include <linux/pm_legacy.h>
#include <linux/device.h>
#include <linux/proc_fs.h>
#ifdef CONFIG_X86
result = acpi_bus_init();
if (!result) {
-#ifdef CONFIG_PM_LEGACY
- if (!PM_IS_ACTIVE())
- pm_active = 1;
+ if (!(pm_flags & PM_APM))
+ pm_flags |= PM_ACPI;
else {
printk(KERN_INFO PREFIX
"APM is already active, exiting\n");
disable_acpi();
result = -ENODEV;
}
-#endif
} else
disable_acpi();
return 0;
}
+int __init acpi_boot_ec_enable(void)
+{
+ if (!boot_ec || boot_ec->handlers_installed)
+ return 0;
+ if (!ec_install_handlers(boot_ec)) {
+ first_ec = boot_ec;
+ return 0;
+ }
+ return -EFAULT;
+}
+
int __init acpi_ec_ecdt_probe(void)
{
int ret;
goto error;
/* We really need to limit this workaround, the only ASUS,
* which needs it, has fake EC._INI method, so use it as flag.
+ * Keep boot_ec struct as it will be needed soon.
*/
if (ACPI_FAILURE(acpi_get_handle(boot_ec->handle, "_INI", &x)))
- goto error;
+ return -ENODEV;
}
ret = ec_install_handlers(boot_ec);
* setup will potentially execute control methods
* (e.g., _REG method for this region)
*/
- acpi_ex_relinquish_interpreter();
+ acpi_ex_exit_interpreter();
status = region_setup(region_obj, ACPI_REGION_ACTIVATE,
handler_desc->address_space.context,
/* Re-enter the interpreter */
- acpi_ex_reacquire_interpreter();
+ acpi_ex_enter_interpreter();
/* Check for failure of the Region Setup */
* exit the interpreter because the handler *might* block -- we don't
* know what it will do, so we can't hold the lock on the intepreter.
*/
- acpi_ex_relinquish_interpreter();
+ acpi_ex_exit_interpreter();
}
/* Call the handler */
* We just returned from a non-default handler, we must re-enter the
* interpreter
*/
- acpi_ex_reacquire_interpreter();
+ acpi_ex_enter_interpreter();
}
return_ACPI_STATUS(status);
&polarity, &link,
acpi_pci_allocate_irq);
+ if (irq < 0) {
+ /*
+ * IDE legacy mode controller IRQs are magic. Why do compat
+ * extensions always make such a nasty mess.
+ */
+ if (dev->class >> 8 == PCI_CLASS_STORAGE_IDE &&
+ (dev->class & 0x05) == 0)
+ return 0;
+ }
/*
* No IRQ known to the ACPI subsystem - maybe the BIOS /
* driver reported one, then use it. Exit in any case.
#define PM_TIMER_TICKS_TO_US(p) (((p) * 1000)/(PM_TIMER_FREQUENCY/1000))
static unsigned int max_cstate __read_mostly = ACPI_PROCESSOR_MAX_POWER;
+#ifdef CONFIG_CPU_IDLE
module_param(max_cstate, uint, 0000);
+#else
+module_param(max_cstate, uint, 0644);
+#endif
static unsigned int nocst __read_mostly;
module_param(nocst, uint, 0000);
#include <linux/jiffies.h>
#include <linux/delay.h>
+#ifdef CONFIG_ACPI_SYSFS_POWER
#include <linux/power_supply.h>
+#endif
#include "sbshc.h"
MODULE_DEVICE_TABLE(acpi, sbs_device_ids);
struct acpi_battery {
+#ifdef CONFIG_ACPI_SYSFS_POWER
struct power_supply bat;
+#endif
struct acpi_sbs *sbs;
#ifdef CONFIG_ACPI_PROCFS_POWER
struct proc_dir_entry *proc_entry;
#define to_acpi_battery(x) container_of(x, struct acpi_battery, bat);
struct acpi_sbs {
+#ifdef CONFIG_ACPI_SYSFS_POWER
struct power_supply charger;
+#endif
struct acpi_device *device;
struct acpi_smb_hc *hc;
struct mutex lock;
acpi_battery_ipscale(battery);
}
+#ifdef CONFIG_ACPI_SYSFS_POWER
static int sbs_get_ac_property(struct power_supply *psy,
enum power_supply_property psp,
union power_supply_propval *val)
POWER_SUPPLY_PROP_MODEL_NAME,
POWER_SUPPLY_PROP_MANUFACTURER,
};
+#endif
/* --------------------------------------------------------------------------
Smart Battery System Management
return result;
}
+#ifdef CONFIG_ACPI_SYSFS_POWER
static ssize_t acpi_battery_alarm_show(struct device *dev,
struct device_attribute *attr,
char *buf)
.show = acpi_battery_alarm_show,
.store = acpi_battery_alarm_store,
};
+#endif
/* --------------------------------------------------------------------------
FS Interface (/proc/acpi)
&acpi_battery_state_fops, &acpi_battery_alarm_fops,
battery);
#endif
+#ifdef CONFIG_ACPI_SYSFS_POWER
battery->bat.name = battery->name;
battery->bat.type = POWER_SUPPLY_TYPE_BATTERY;
if (!acpi_battery_mode(battery)) {
goto end;
battery->have_sysfs_alarm = 1;
end:
+#endif
printk(KERN_INFO PREFIX "%s [%s]: Battery Slot [%s] (battery %s)\n",
ACPI_SBS_DEVICE_NAME, acpi_device_bid(sbs->device),
battery->name, sbs->battery->present ? "present" : "absent");
static void acpi_battery_remove(struct acpi_sbs *sbs, int id)
{
struct acpi_battery *battery = &sbs->battery[id];
-
+#ifdef CONFIG_ACPI_SYSFS_POWER
if (battery->bat.dev) {
if (battery->have_sysfs_alarm)
device_remove_file(battery->bat.dev, &alarm_attr);
power_supply_unregister(&battery->bat);
}
+#endif
#ifdef CONFIG_ACPI_PROCFS_POWER
if (battery->proc_entry)
acpi_sbs_remove_fs(&battery->proc_entry, acpi_battery_dir);
if (result)
goto end;
#endif
+#ifdef CONFIG_ACPI_SYSFS_POWER
sbs->charger.name = "sbs-charger";
sbs->charger.type = POWER_SUPPLY_TYPE_MAINS;
sbs->charger.properties = sbs_ac_props;
sbs->charger.num_properties = ARRAY_SIZE(sbs_ac_props);
sbs->charger.get_property = sbs_get_ac_property;
power_supply_register(&sbs->device->dev, &sbs->charger);
+#endif
printk(KERN_INFO PREFIX "%s [%s]: AC Adapter [%s] (%s)\n",
ACPI_SBS_DEVICE_NAME, acpi_device_bid(sbs->device),
ACPI_AC_DIR_NAME, sbs->charger_present ? "on-line" : "off-line");
static void acpi_charger_remove(struct acpi_sbs *sbs)
{
+#ifdef CONFIG_ACPI_SYSFS_POWER
if (sbs->charger.dev)
power_supply_unregister(&sbs->charger);
+#endif
#ifdef CONFIG_ACPI_PROCFS_POWER
if (sbs->charger_entry)
acpi_sbs_remove_fs(&sbs->charger_entry, acpi_ac_dir);
ACPI_SBS_NOTIFY_STATUS,
sbs->charger_present);
#endif
+#ifdef CONFIG_ACPI_SYSFS_POWER
kobject_uevent(&sbs->charger.dev->kobj, KOBJ_CHANGE);
+#endif
}
if (sbs->manager_present) {
for (id = 0; id < MAX_SBS_BAT; ++id) {
ACPI_SBS_NOTIFY_STATUS,
bat->present);
#endif
+#ifdef CONFIG_ACPI_SYSFS_POWER
kobject_uevent(&bat->bat.dev->kobj, KOBJ_CHANGE);
+#endif
}
}
}
return result;
}
+int __init acpi_boot_ec_enable(void);
+
static int __init acpi_scan_init(void)
{
int result;
* Enumerate devices in the ACPI namespace.
*/
result = acpi_bus_scan_fixed(acpi_root);
+
+ /* EC region might be needed at bus_scan, so enable it now */
+ acpi_boot_ec_enable();
+
if (!result)
result = acpi_bus_scan(acpi_root, &ops);
ehc->i.action &= ~ATA_EH_PERDEV_MASK;
}
- /* consider speeding down */
+ /* propagate timeout to host link */
+ if ((all_err_mask & AC_ERR_TIMEOUT) && !ata_is_host_link(link))
+ ap->link.eh_context.i.err_mask |= AC_ERR_TIMEOUT;
+
+ /* record error and consider speeding down */
dev = ehc->i.dev;
- if (!dev && ata_link_max_devices(link) == 1 &&
- ata_dev_enabled(link->device))
- dev = link->device;
+ if (!dev && ((ata_link_max_devices(link) == 1 &&
+ ata_dev_enabled(link->device))))
+ dev = link->device;
if (dev)
ehc->i.action |= ata_eh_speed_down(dev, is_io, all_err_mask);
{
struct ata_link *link;
- __ata_port_for_each_link(link, ap)
+ ata_port_for_each_link(link, ap)
ata_eh_link_autopsy(link);
+
+ /* Autopsy of fanout ports can affect host link autopsy.
+ * Perform host link autopsy last.
+ */
+ if (ap->nr_pmp_links)
+ ata_eh_link_autopsy(&ap->link);
}
/**
if (ata_link_offline(link))
continue;
- /* apply class override and convert UNKNOWN to NONE */
+ /* apply class override */
if (lflags & ATA_LFLAG_ASSUME_ATA)
classes[dev->devno] = ATA_DEV_ATA;
else if (lflags & ATA_LFLAG_ASSUME_SEMB)
classes[dev->devno] = ATA_DEV_SEMB_UNSUP; /* not yet */
- else if (classes[dev->devno] == ATA_DEV_UNKNOWN)
- classes[dev->devno] = ATA_DEV_NONE;
}
/* record current link speed */
/* SError.N need a kick in the ass to get working */
link->flags |= ATA_LFLAG_HRST_TO_RESUME;
- /* class code report is unreliable */
- if (link->pmp < 5)
- link->flags |= ATA_LFLAG_ASSUME_ATA;
-
- /* The config device, which can be either at
- * port 0 or 5, locks up on SRST.
+ /* Class code report is unreliable and SRST
+ * times out under certain configurations.
+ * Config device can be at port 0 or 5 and
+ * locks up on SRST.
*/
- if (link->pmp == 0 || link->pmp == 5)
+ if (link->pmp <= 5)
link->flags |= ATA_LFLAG_NO_SRST |
ATA_LFLAG_ASSUME_ATA;
ata_scsi_sdev_config(sdev);
- sdev->manage_start_stop = 1;
+ if (dev->class == ATA_DEV_ATA)
+ sdev->manage_start_stop = 1;
if (dev)
ata_scsi_dev_config(sdev, dev);
if (rc)
goto err_out;
- if (!legacy_mode) {
+ if (!legacy_mode && pdev->irq) {
+ /* We may have no IRQ assigned in which case we can poll. This
+ shouldn't happen on a sane system but robustness is cheap
+ in this case */
rc = devm_request_irq(dev, pdev->irq, pi->port_ops->irq_handler,
IRQF_SHARED, DRV_NAME, host);
if (rc)
ata_port_desc(host->ports[0], "irq %d", pdev->irq);
ata_port_desc(host->ports[1], "irq %d", pdev->irq);
- } else {
+ } else if (legacy_mode) {
if (!ata_port_is_dummy(host->ports[0])) {
rc = devm_request_irq(dev, ATA_PRIMARY_IRQ(pdev),
pi->port_ops->irq_handler,
.port_start = ata_port_start,
};
-static void ixp4xx_setup_port(struct ata_ioports *ioaddr,
+static void ixp4xx_setup_port(struct ata_port *ap,
struct ixp4xx_pata_data *data,
unsigned long raw_cs0, unsigned long raw_cs1)
{
+ struct ata_ioports *ioaddr = &ap->ioaddr;
unsigned long raw_cmd = raw_cs0;
unsigned long raw_ctl = raw_cs1 + 0x06;
/* Flip back to 33Mhz for PIO */
if (adev->dma_mode >= XFER_UDMA_2)
iowrite8(ioread8(clock) & ~sel66, clock);
-
ata_bmdma_stop(qc);
+ pdc202xx_set_piomode(ap, adev);
}
/**
adev->max_sectors = 256;
}
+static int pdc2026x_port_start(struct ata_port *ap)
+{
+ void __iomem *bmdma = ap->ioaddr.bmdma_addr;
+ if (bmdma) {
+ /* Enable burst mode */
+ u8 burst = ioread8(bmdma + 0x1f);
+ iowrite8(burst | 0x01, bmdma + 0x1f);
+ }
+ return ata_sff_port_start(ap);
+}
+
static struct scsi_host_template pdc202xx_sht = {
.module = THIS_MODULE,
.name = DRV_NAME,
.irq_clear = ata_bmdma_irq_clear,
.irq_on = ata_irq_on,
- .port_start = ata_sff_port_start,
+ .port_start = pdc2026x_port_start,
};
static int pdc202xx_init_one(struct pci_dev *dev, const struct pci_device_id *id)
static void qs_error_handler(struct ata_port *ap)
{
qs_enter_reg_mode(ap);
- ata_do_eh(ap, qs_prereset, ata_std_softreset, NULL,
+ ata_do_eh(ap, qs_prereset, NULL, sata_std_hardreset,
ata_std_postreset);
}
struct ata_link *link = qc->dev->link;
struct ata_port *ap = link->ap;
u8 prot = qc->tf.protocol;
- int is_atapi = (prot == ATA_PROT_ATAPI ||
- prot == ATA_PROT_ATAPI_NODATA ||
- prot == ATA_PROT_ATAPI_DMA);
-
- /* ATAPI commands completing with CHECK_SENSE cause various
- * weird problems if other commands are active. PMP DMA CS
- * errata doesn't cover all and HSM violation occurs even with
- * only one other device active. Always run an ATAPI command
- * by itself.
- */
+
+ /*
+ * There is a bug in the chip:
+ * Port LRAM Causes the PRB/SGT Data to be Corrupted
+ * If the host issues a read request for LRAM and SActive registers
+ * while active commands are available in the port, PRB/SGT data in
+ * the LRAM can become corrupted. This issue applies only when
+ * reading from, but not writing to, the LRAM.
+ *
+ * Therefore, reading LRAM when there is no particular error [and
+ * other commands may be outstanding] is prohibited.
+ *
+ * To avoid this bug there are two situations where a command must run
+ * exclusive of any other commands on the port:
+ *
+ * - ATAPI commands which check the sense data
+ * - Passthrough ATA commands which always have ATA_QCFLAG_RESULT_TF
+ * set.
+ *
+ */
+ int is_excl = (prot == ATA_PROT_ATAPI ||
+ prot == ATA_PROT_ATAPI_NODATA ||
+ prot == ATA_PROT_ATAPI_DMA ||
+ (qc->flags & ATA_QCFLAG_RESULT_TF));
+
if (unlikely(ap->excl_link)) {
if (link == ap->excl_link) {
if (ap->nr_active_links)
qc->flags |= ATA_QCFLAG_CLEAR_EXCL;
} else
return ATA_DEFER_PORT;
- } else if (unlikely(is_atapi)) {
+ } else if (unlikely(is_excl)) {
ap->excl_link = link;
if (ap->nr_active_links)
return ATA_DEFER_PORT;
if (mac[i] == NULL)
nicstar_init_eprom(card->membase);
- if (request_irq(pcidev->irq, &ns_irq_handler, IRQF_DISABLED | IRQF_SHARED, "nicstar", card) != 0)
- {
- printk("nicstar%d: can't allocate IRQ %d.\n", i, pcidev->irq);
- error = 9;
- ns_init_card_error(card, error);
- return error;
- }
-
/* Set the VPI/VCI MSb mask to zero so we can receive OAM cells */
writel(0x00000000, card->membase + VPM);
card->iovpool.count++;
}
- card->intcnt = 0;
-
/* Configure NICStAR */
if (card->rct_size == 4096)
ns_cfg_rctsize = NS_CFG_RCTSIZE_4096_ENTRIES;
card->efbie = 1;
+ card->intcnt = 0;
+ if (request_irq(pcidev->irq, &ns_irq_handler, IRQF_DISABLED | IRQF_SHARED, "nicstar", card) != 0)
+ {
+ printk("nicstar%d: can't allocate IRQ %d.\n", i, pcidev->irq);
+ error = 9;
+ ns_init_card_error(card, error);
+ return error;
+ }
+
/* Register device */
card->atmdev = atm_dev_register("nicstar", &atm_ops, -1, NULL);
if (card->atmdev == NULL)
EXPORT_SYMBOL(tty_termios_copy_hw);
/**
+ * tty_termios_hw_change - check for setting change
+ * @a: termios
+ * @b: termios to compare
+ *
+ * Check if any of the bits that affect a dumb device have changed
+ * between the two termios structures, or a speed change is needed.
+ */
+
+int tty_termios_hw_change(struct ktermios *a, struct ktermios *b)
+{
+ if (a->c_ispeed != b->c_ispeed || a->c_ospeed != b->c_ospeed)
+ return 1;
+ if ((a->c_cflag ^ b->c_cflag) & ~(HUPCL | CREAD | CLOCAL))
+ return 1;
+ return 0;
+}
+EXPORT_SYMBOL(tty_termios_hw_change);
+
+/**
* change_termios - update termios values
* @tty: tty to update
* @new_termios: desired new value
spin_unlock_bh(&dev->queue_lock);
if (found) {
- atomic_dec(&dev->refcnt);
cn_queue_free_callback(cbq);
+ atomic_dec(&dev->refcnt);
return -EINVAL;
}
if (queue_work(dev->cbdev->cn_queue,
&__cbq->work))
err = 0;
+ else
+ err = -EINVAL;
} else {
struct cn_callback_data *d;
/* ====== Encryption/decryption routines ====== */
/* These are the real call to PadLock. */
+static inline void padlock_xcrypt(const u8 *input, u8 *output, void *key,
+ void *control_word)
+{
+ asm volatile (".byte 0xf3,0x0f,0xa7,0xc8" /* rep xcryptecb */
+ : "+S"(input), "+D"(output)
+ : "d"(control_word), "b"(key), "c"(1));
+}
+
+static void aes_crypt_copy(const u8 *in, u8 *out, u32 *key, struct cword *cword)
+{
+ u8 buf[AES_BLOCK_SIZE * 2 + PADLOCK_ALIGNMENT - 1];
+ u8 *tmp = PTR_ALIGN(&buf[0], PADLOCK_ALIGNMENT);
+
+ memcpy(tmp, in, AES_BLOCK_SIZE);
+ padlock_xcrypt(tmp, out, key, cword);
+}
+
+static inline void aes_crypt(const u8 *in, u8 *out, u32 *key,
+ struct cword *cword)
+{
+ asm volatile ("pushfl; popfl");
+
+ /* padlock_xcrypt requires at least two blocks of data. */
+ if (unlikely(!(((unsigned long)in ^ (PAGE_SIZE - AES_BLOCK_SIZE)) &
+ (PAGE_SIZE - 1)))) {
+ aes_crypt_copy(in, out, key, cword);
+ return;
+ }
+
+ padlock_xcrypt(in, out, key, cword);
+}
+
static inline void padlock_xcrypt_ecb(const u8 *input, u8 *output, void *key,
void *control_word, u32 count)
{
+ if (count == 1) {
+ aes_crypt(input, output, key, control_word);
+ return;
+ }
+
asm volatile ("pushfl; popfl"); /* enforce key reload. */
- asm volatile (".byte 0xf3,0x0f,0xa7,0xc8" /* rep xcryptecb */
+ asm volatile ("test $1, %%cl;"
+ "je 1f;"
+ "lea -1(%%ecx), %%eax;"
+ "mov $1, %%ecx;"
+ ".byte 0xf3,0x0f,0xa7,0xc8;" /* rep xcryptecb */
+ "mov %%eax, %%ecx;"
+ "1:"
+ ".byte 0xf3,0x0f,0xa7,0xc8" /* rep xcryptecb */
: "+S"(input), "+D"(output)
- : "d"(control_word), "b"(key), "c"(count));
+ : "d"(control_word), "b"(key), "c"(count)
+ : "ax");
}
static inline u8 *padlock_xcrypt_cbc(const u8 *input, u8 *output, void *key,
static void aes_encrypt(struct crypto_tfm *tfm, u8 *out, const u8 *in)
{
struct aes_ctx *ctx = aes_ctx(tfm);
- padlock_xcrypt_ecb(in, out, ctx->E, &ctx->cword.encrypt, 1);
+ aes_crypt(in, out, ctx->E, &ctx->cword.encrypt);
}
static void aes_decrypt(struct crypto_tfm *tfm, u8 *out, const u8 *in)
{
struct aes_ctx *ctx = aes_ctx(tfm);
- padlock_xcrypt_ecb(in, out, ctx->D, &ctx->cword.decrypt, 1);
+ aes_crypt(in, out, ctx->D, &ctx->cword.decrypt);
}
static struct crypto_alg aes_alg = {
extern int dmi_available;
-static int __init dmi_id_init(void)
+/* In a separate function to keep gcc 3.2 happy - do NOT merge this in
+ dmi_id_init! */
+static void __init dmi_id_init_attr_table(void)
{
- int ret, i;
-
- if (!dmi_available)
- return -ENODEV;
+ int i;
/* Not necessarily all DMI fields are available on all
* systems, hence let's built an attribute table of just
ADD_DMI_ATTR(chassis_serial, DMI_CHASSIS_SERIAL);
ADD_DMI_ATTR(chassis_asset_tag, DMI_CHASSIS_ASSET_TAG);
sys_dmi_attributes[i++] = &sys_dmi_modalias_attr.attr;
+}
+
+static int __init dmi_id_init(void)
+{
+ int ret;
+
+ if (!dmi_available)
+ return -ENODEV;
+
+ dmi_id_init_attr_table();
ret = class_register(&dmi_class);
if (ret)
data->vrm = vid_which_vrm();
superio_enter(sio_data->sioreg);
- /* Set VID input sensibility if needed. In theory the BIOS should
- have set it, but in practice it's not always the case. */
- en_vrm10 = superio_inb(sio_data->sioreg, SIO_REG_EN_VRM10);
- if ((en_vrm10 & 0x08) && data->vrm != 100) {
- dev_warn(dev, "Setting VID input voltage to TTL\n");
- superio_outb(sio_data->sioreg, SIO_REG_EN_VRM10,
- en_vrm10 & ~0x08);
- } else if (!(en_vrm10 & 0x08) && data->vrm == 100) {
- dev_warn(dev, "Setting VID input voltage to VRM10\n");
- superio_outb(sio_data->sioreg, SIO_REG_EN_VRM10,
- en_vrm10 | 0x08);
- }
/* Read VID value */
superio_select(sio_data->sioreg, W83627EHF_LD_HWM);
- if (superio_inb(sio_data->sioreg, SIO_REG_VID_CTRL) & 0x80)
+ if (superio_inb(sio_data->sioreg, SIO_REG_VID_CTRL) & 0x80) {
+ /* Set VID input sensibility if needed. In theory the BIOS
+ should have set it, but in practice it's not always the
+ case. We only do it for the W83627EHF/EHG because the
+ W83627DHG is more complex in this respect. */
+ if (sio_data->kind == w83627ehf) {
+ en_vrm10 = superio_inb(sio_data->sioreg,
+ SIO_REG_EN_VRM10);
+ if ((en_vrm10 & 0x08) && data->vrm == 90) {
+ dev_warn(dev, "Setting VID input voltage to "
+ "TTL\n");
+ superio_outb(sio_data->sioreg, SIO_REG_EN_VRM10,
+ en_vrm10 & ~0x08);
+ } else if (!(en_vrm10 & 0x08) && data->vrm == 100) {
+ dev_warn(dev, "Setting VID input voltage to "
+ "VRM10\n");
+ superio_outb(sio_data->sioreg, SIO_REG_EN_VRM10,
+ en_vrm10 | 0x08);
+ }
+ }
+
data->vid = superio_inb(sio_data->sioreg, SIO_REG_VID_DATA) & 0x3f;
- else {
+ } else {
dev_info(dev, "VID pins in output mode, CPU VID not "
"available\n");
data->vid = 0x3f;
#include <acpi/acpi.h>
#include <linux/ide.h>
#include <linux/pci.h>
+#include <linux/dmi.h>
#include <acpi/acpi_bus.h>
#include <acpi/acnames.h>
extern int ide_noacpitfs;
extern int ide_noacpionboot;
+static bool ide_noacpi_psx;
+static int no_acpi_psx(const struct dmi_system_id *id)
+{
+ ide_noacpi_psx = true;
+ printk(KERN_NOTICE"%s detected - disable ACPI _PSx.\n", id->ident);
+ return 0;
+}
+
+static const struct dmi_system_id ide_acpi_dmi_table[] = {
+ /* Bug 9673. */
+ /* We should check if this is because ACPI NVS isn't save/restored. */
+ {
+ .callback = no_acpi_psx,
+ .ident = "HP nx9005",
+ .matches = {
+ DMI_MATCH(DMI_BIOS_VENDOR, "Phoenix Technologies Ltd."),
+ DMI_MATCH(DMI_BIOS_VERSION, "KAM1.60")
+ },
+ },
+};
+
+static int ide_acpi_blacklist(void)
+{
+ static int done;
+ if (done)
+ return 0;
+ done = 1;
+ dmi_check_system(ide_acpi_dmi_table);
+ return 0;
+}
+
/**
* ide_get_dev_handle - finds acpi_handle and PCI device.function
* @dev: device to locate
{
int unit;
- if (ide_noacpi)
+ if (ide_noacpi || ide_noacpi_psx)
return;
DEBPRINT("ENTER:\n");
struct ide_acpi_drive_link *master;
struct ide_acpi_drive_link *slave;
+ ide_acpi_blacklist();
+
hwif->acpidata = kzalloc(sizeof(struct ide_acpi_hwif_link), GFP_KERNEL);
if (!hwif->acpidata)
return;
printk(KERN_DEBUG "%s: skipping word 93 validity check\n",
drive->name);
+ if (ide_dev_is_sata(id) && !ivb)
+ return 1;
+
if (hwif->cbl != ATA_CBL_PATA80 && !ivb)
goto no_80w;
- if (ide_dev_is_sata(id))
- return 1;
-
/*
* FIXME:
* - force bit13 (80c cable present) check also for !ivb devices
/*
- * linux/drivers/ide/pci/trm290.c Version 1.02 Mar. 18, 2000
+ * linux/drivers/ide/pci/trm290.c Version 1.05 Dec. 26, 2007
*
* Copyright (c) 1997-1998 Mark Lord
+ * Copyright (c) 2007 MontaVista Software, Inc. <source@mvista.com>
* May be copied or modified under the terms of the GNU General Public License
*
* June 22, 2004 - get rid of check_region
trm290_prepare_drive(drive, drive->using_dma);
}
-static void trm290_ide_dma_exec_cmd(ide_drive_t *drive, u8 command)
+static void trm290_dma_exec_cmd(ide_drive_t *drive, u8 command)
{
BUG_ON(HWGROUP(drive)->handler != NULL); /* paranoia check */
ide_set_handler(drive, &ide_dma_intr, WAIT_CMD, NULL);
outb(command, IDE_COMMAND_REG);
}
-static int trm290_ide_dma_setup(ide_drive_t *drive)
+static int trm290_dma_setup(ide_drive_t *drive)
{
ide_hwif_t *hwif = drive->hwif;
struct request *rq = hwif->hwgroup->rq;
return 0;
}
-static void trm290_ide_dma_start(ide_drive_t *drive)
+static void trm290_dma_start(ide_drive_t *drive)
{
}
return (status == 0x00ff);
}
+static void trm290_dma_host_on(ide_drive_t *drive)
+{
+}
+
+static void trm290_dma_host_off(ide_drive_t *drive)
+{
+}
+
static void __devinit init_hwif_trm290(ide_hwif_t *hwif)
{
unsigned int cfgbase = 0;
ide_setup_dma(hwif, (hwif->config_data + 4) ^ (hwif->channel ? 0x0080 : 0x0000), 3);
- hwif->dma_setup = &trm290_ide_dma_setup;
- hwif->dma_exec_cmd = &trm290_ide_dma_exec_cmd;
- hwif->dma_start = &trm290_ide_dma_start;
- hwif->ide_dma_end = &trm290_ide_dma_end;
- hwif->ide_dma_test_irq = &trm290_ide_dma_test_irq;
+ hwif->dma_host_off = &trm290_dma_host_off;
+ hwif->dma_host_on = &trm290_dma_host_on;
+ hwif->dma_setup = &trm290_dma_setup;
+ hwif->dma_exec_cmd = &trm290_dma_exec_cmd;
+ hwif->dma_start = &trm290_dma_start;
+ hwif->ide_dma_end = &trm290_ide_dma_end;
+ hwif->ide_dma_test_irq = &trm290_ide_dma_test_irq;
hwif->selectproc = &trm290_selectproc;
#if 1
wc->dlid_path_bits = (be32_to_cpu(cqe->g_mlpath_rqpn) >> 24) & 0x7f;
wc->wc_flags |= be32_to_cpu(cqe->g_mlpath_rqpn) & 0x80000000 ?
IB_WC_GRH : 0;
- wc->pkey_index = be32_to_cpu(cqe->immed_rss_invalid) >> 16;
+ wc->pkey_index = be32_to_cpu(cqe->immed_rss_invalid) & 0x7f;
}
return 0;
list_for_each_entry_safe(target, tmp_target,
&host->target_list, list) {
+ srp_remove_host(target->scsi_host);
scsi_remove_host(target->scsi_host);
srp_disconnect_target(target);
ib_destroy_cm_id(target->cm_id);
dflag = 0;
count_pull = count_put = 0;
while ((count_pull < skb->len) && (len > 0)) {
+ /* push every character but the last to the tty buffer directly */
+ if ( count_put )
+ tty_insert_flip_char(tty, last, TTY_NORMAL);
len--;
if (dev->drv[di]->DLEflag & DLEmask) {
last = DLE;
tty_insert_flip_char(tty, DLE, 0);
tty_insert_flip_char(tty, *dp++, 0);
}
+ if (*dp == DLE)
+ tty_insert_flip_char(tty, DLE, 0);
last = *dp;
} else {
#endif
if ((info->flags & ISDN_ASYNC_CLOSING) || (!info->tty)) {
return;
}
+#ifdef CONFIG_ISDN_AUDIO
+ if ( !info->vonline )
+ tty_ldisc_flush(info->tty);
+#else
tty_ldisc_flush(info->tty);
+#endif
if ((info->flags & ISDN_ASYNC_CHECK_CD) &&
(!((info->flags & ISDN_ASYNC_CALLOUT_ACTIVE) &&
(info->flags & ISDN_ASYNC_CALLOUT_NOHUP)))) {
goto err_out;
/* add to the list of leds */
- write_lock(&leds_list_lock);
+ down_write(&leds_list_lock);
list_add_tail(&led_cdev->node, &leds_list);
- write_unlock(&leds_list_lock);
+ up_write(&leds_list_lock);
#ifdef CONFIG_LEDS_TRIGGERS
init_rwsem(&led_cdev->trigger_lock);
device_unregister(led_cdev->dev);
- write_lock(&leds_list_lock);
+ down_write(&leds_list_lock);
list_del(&led_cdev->node);
- write_unlock(&leds_list_lock);
+ up_write(&leds_list_lock);
}
EXPORT_SYMBOL_GPL(led_classdev_unregister);
#include <linux/kernel.h>
#include <linux/list.h>
#include <linux/module.h>
-#include <linux/spinlock.h>
+#include <linux/rwsem.h>
#include <linux/leds.h>
#include "leds.h"
-DEFINE_RWLOCK(leds_list_lock);
+DECLARE_RWSEM(leds_list_lock);
LIST_HEAD(leds_list);
EXPORT_SYMBOL_GPL(leds_list);
up_write(&triggers_list_lock);
/* Register with any LEDs that have this as a default trigger */
- read_lock(&leds_list_lock);
+ down_read(&leds_list_lock);
list_for_each_entry(led_cdev, &leds_list, node) {
down_write(&led_cdev->trigger_lock);
if (!led_cdev->trigger && led_cdev->default_trigger &&
led_trigger_set(led_cdev, trigger);
up_write(&led_cdev->trigger_lock);
}
- read_unlock(&leds_list_lock);
+ up_read(&leds_list_lock);
return 0;
}
up_write(&triggers_list_lock);
/* Remove anyone actively using this trigger */
- read_lock(&leds_list_lock);
+ down_read(&leds_list_lock);
list_for_each_entry(led_cdev, &leds_list, node) {
down_write(&led_cdev->trigger_lock);
if (led_cdev->trigger == trigger)
led_trigger_set(led_cdev, NULL);
up_write(&led_cdev->trigger_lock);
}
- read_unlock(&leds_list_lock);
+ up_read(&leds_list_lock);
}
void led_trigger_unregister_simple(struct led_trigger *trigger)
static void locomoled_brightness_set(struct led_classdev *led_cdev,
enum led_brightness value, int offset)
{
- struct locomo_dev *locomo_dev = LOCOMO_DEV(led_cdev->dev);
+ struct locomo_dev *locomo_dev = LOCOMO_DEV(led_cdev->dev->parent);
unsigned long flags;
local_irq_save(flags);
#define __LEDS_H_INCLUDED
#include <linux/device.h>
+#include <linux/rwsem.h>
#include <linux/leds.h>
static inline void led_set_brightness(struct led_classdev *led_cdev,
led_cdev->brightness_set(led_cdev, value);
}
-extern rwlock_t leds_list_lock;
+extern struct rw_semaphore leds_list_lock;
extern struct list_head leds_list;
#ifdef CONFIG_LEDS_TRIGGERS
md_done_sync(conf->mddev, STRIPE_SECTORS, 1);
}
- if (s.expanding && s.locked == 0)
+ if (s.expanding && s.locked == 0 &&
+ !test_bit(STRIPE_OP_COMPUTE_BLK, &sh->ops.pending))
handle_stripe_expansion(conf, sh, NULL);
if (sh->ops.count)
md_done_sync(conf->mddev, STRIPE_SECTORS, 1);
}
- if (s.expanding && s.locked == 0)
+ if (s.expanding && s.locked == 0 &&
+ !test_bit(STRIPE_OP_COMPUTE_BLK, &sh->ops.pending))
handle_stripe_expansion(conf, sh, &r6s);
spin_unlock(&sh->lock);
struct video_mbuf *mbuf = arg;
unsigned int i;
- mutex_lock(&fh->cap.lock);
retval = videobuf_mmap_setup(&fh->cap,gbuffers,gbufsize,
V4L2_MEMORY_MMAP);
if (retval < 0)
- goto fh_unlock_and_return;
+ return retval;
gbuffers = retval;
memset(mbuf,0,sizeof(*mbuf));
mbuf->size = gbuffers * gbufsize;
for (i = 0; i < gbuffers; i++)
mbuf->offsets[i] = i * gbufsize;
- mutex_unlock(&fh->cap.lock);
return 0;
}
case VIDIOCMCAPTURE:
ivtv_process_eeprom(itv);
}
+ /* The mspx4xx chips need a longer delay for some reason */
+ if (!(itv->hw_flags & IVTV_HW_MSP34XX))
+ itv->i2c_algo.udelay = 5;
+
if (itv->std == 0) {
itv->std = V4L2_STD_NTSC_M;
}
.setscl = ivtv_setscl_old,
.getsda = ivtv_getsda_old,
.getscl = ivtv_getscl_old,
- .udelay = 5,
+ .udelay = 10,
.timeout = 200,
};
sizeof(struct i2c_adapter));
memcpy(&itv->i2c_algo, &ivtv_i2c_algo_template,
sizeof(struct i2c_algo_bit_data));
- /* The mspx4xx chips need a longer delay for some reason */
- if (itv->hw_flags & IVTV_HW_MSP34XX)
- itv->i2c_algo.udelay = 10;
itv->i2c_algo.data = itv;
itv->i2c_adap.algo_data = &itv->i2c_algo;
}
#define DRV_MODULE_NAME "cassini"
#define PFX DRV_MODULE_NAME ": "
-#define DRV_MODULE_VERSION "1.4"
-#define DRV_MODULE_RELDATE "1 July 2004"
+#define DRV_MODULE_VERSION "1.5"
+#define DRV_MODULE_RELDATE "4 Jan 2008"
#define CAS_DEF_MSG_ENABLE \
(NETIF_MSG_DRV | \
cas_disable_irq(cp, i);
}
-static inline void cas_buffer_init(cas_page_t *cp)
-{
- struct page *page = cp->buffer;
- atomic_set((atomic_t *)&page->lru.next, 1);
-}
-
-static inline int cas_buffer_count(cas_page_t *cp)
-{
- struct page *page = cp->buffer;
- return atomic_read((atomic_t *)&page->lru.next);
-}
-
-static inline void cas_buffer_inc(cas_page_t *cp)
-{
- struct page *page = cp->buffer;
- atomic_inc((atomic_t *)&page->lru.next);
-}
-
-static inline void cas_buffer_dec(cas_page_t *cp)
-{
- struct page *page = cp->buffer;
- atomic_dec((atomic_t *)&page->lru.next);
-}
-
static void cas_enable_irq(struct cas *cp, const int ring)
{
if (ring == 0) { /* all but TX_DONE */
{
pci_unmap_page(cp->pdev, page->dma_addr, cp->page_size,
PCI_DMA_FROMDEVICE);
- cas_buffer_dec(page);
__free_pages(page->buffer, cp->page_order);
kfree(page);
return 0;
page->buffer = alloc_pages(flags, cp->page_order);
if (!page->buffer)
goto page_err;
- cas_buffer_init(page);
page->dma_addr = pci_map_page(cp->pdev, page->buffer, 0,
cp->page_size, PCI_DMA_FROMDEVICE);
return page;
list_for_each_safe(elem, tmp, &list) {
cas_page_t *page = list_entry(elem, cas_page_t, list);
- if (cas_buffer_count(page) > 1)
+ if (page_count(page->buffer) > 1)
continue;
list_del(elem);
cas_page_t *page = cp->rx_pages[1][index];
cas_page_t *new;
- if (cas_buffer_count(page) == 1)
+ if (page_count(page->buffer) == 1)
return page;
new = cas_page_dequeue(cp);
cas_page_t **page1 = cp->rx_pages[1];
/* swap if buffer is in use */
- if (cas_buffer_count(page0[index]) > 1) {
+ if (page_count(page0[index]->buffer) > 1) {
cas_page_t *new = cas_page_spare(cp, index);
if (new) {
page1[index] = page0[index];
struct cas_page *page;
struct sk_buff *skb;
void *addr, *crcaddr;
+ __sum16 csum;
char *p;
hlen = CAS_VAL(RX_COMP2_HDR_SIZE, words[1]);
skb_shinfo(skb)->nr_frags++;
skb->data_len += hlen - swivel;
+ skb->truesize += hlen - swivel;
skb->len += hlen - swivel;
get_page(page->buffer);
- cas_buffer_inc(page);
frag->page = page->buffer;
frag->page_offset = off;
frag->size = hlen - swivel;
frag++;
get_page(page->buffer);
- cas_buffer_inc(page);
frag->page = page->buffer;
frag->page_offset = 0;
frag->size = hlen;
skb_put(skb, alloclen);
}
- i = CAS_VAL(RX_COMP4_TCP_CSUM, words[3]);
+ csum = (__force __sum16)htons(CAS_VAL(RX_COMP4_TCP_CSUM, words[3]));
if (cp->crc_size) {
/* checksum includes FCS. strip it out. */
- i = csum_fold(csum_partial(crcaddr, cp->crc_size, i));
+ csum = csum_fold(csum_partial(crcaddr, cp->crc_size,
+ csum_unfold(csum)));
if (addr)
cas_page_unmap(addr);
}
- skb->csum = ntohs(i ^ 0xffff);
+ skb->csum = csum_unfold(~csum);
skb->ip_summed = CHECKSUM_COMPLETE;
skb->protocol = eth_type_trans(skb, cp->dev);
return len;
released = 0;
while (entry != last) {
/* make a new buffer if it's still in use */
- if (cas_buffer_count(page[entry]) > 1) {
+ if (page_count(page[entry]->buffer) > 1) {
cas_page_t *new = cas_page_dequeue(cp);
if (!new) {
/* let the timer know that we need to
{
struct cas *cp = container_of(napi, struct cas, napi);
struct net_device *dev = cp->dev;
- int i, enable_intr, todo, credits;
+ int i, enable_intr, credits;
u32 status = readl(cp->regs + REG_INTR_STATUS);
unsigned long flags;
struct cas *cp = netdev_priv(dev);
#ifdef USE_NAPI
- napi_enable(&cp->napi);
+ napi_disable(&cp->napi);
#endif
/* Make sure we don't get distracted by suspend/resume */
mutex_lock(&cp->pm_mutex);
return rc;
}
+/* When this chip sits underneath an Intel 31154 bridge, it is the
+ * only subordinate device and we can tweak the bridge settings to
+ * reflect that fact.
+ */
+static void __devinit cas_program_bridge(struct pci_dev *cas_pdev)
+{
+ struct pci_dev *pdev = cas_pdev->bus->self;
+ u32 val;
+
+ if (!pdev)
+ return;
+
+ if (pdev->vendor != 0x8086 || pdev->device != 0x537c)
+ return;
+
+ /* Clear bit 10 (Bus Parking Control) in the Secondary
+ * Arbiter Control/Status Register which lives at offset
+ * 0x41. Using a 32-bit word read/modify/write at 0x40
+ * is much simpler so that's how we do this.
+ */
+ pci_read_config_dword(pdev, 0x40, &val);
+ val &= ~0x00040000;
+ pci_write_config_dword(pdev, 0x40, val);
+
+ /* Max out the Multi-Transaction Timer settings since
+ * Cassini is the only device present.
+ *
+ * The register is 16-bit and lives at 0x50. When the
+ * settings are enabled, it extends the GRANT# signal
+ * for a requestor after a transaction is complete. This
+ * allows the next request to run without first needing
+ * to negotiate the GRANT# signal back.
+ *
+ * Bits 12:10 define the grant duration:
+ *
+ * 1 -- 16 clocks
+ * 2 -- 32 clocks
+ * 3 -- 64 clocks
+ * 4 -- 128 clocks
+ * 5 -- 256 clocks
+ *
+ * All other values are illegal.
+ *
+ * Bits 09:00 define which REQ/GNT signal pairs get the
+ * GRANT# signal treatment. We set them all.
+ */
+ pci_write_config_word(pdev, 0x50, (5 << 10) | 0x3ff);
+
+ /* The Read Prefecth Policy register is 16-bit and sits at
+ * offset 0x52. It enables a "smart" pre-fetch policy. We
+ * enable it and max out all of the settings since only one
+ * device is sitting underneath and thus bandwidth sharing is
+ * not an issue.
+ *
+ * The register has several 3 bit fields, which indicates a
+ * multiplier applied to the base amount of prefetching the
+ * chip would do. These fields are at:
+ *
+ * 15:13 --- ReRead Primary Bus
+ * 12:10 --- FirstRead Primary Bus
+ * 09:07 --- ReRead Secondary Bus
+ * 06:04 --- FirstRead Secondary Bus
+ *
+ * Bits 03:00 control which REQ/GNT pairs the prefetch settings
+ * get enabled on. Bit 3 is a grouped enabler which controls
+ * all of the REQ/GNT pairs from [8:3]. Bits 2 to 0 control
+ * the individual REQ/GNT pairs [2:0].
+ */
+ pci_write_config_word(pdev, 0x52,
+ (0x7 << 13) |
+ (0x7 << 10) |
+ (0x7 << 7) |
+ (0x7 << 4) |
+ (0xf << 0));
+
+ /* Force cacheline size to 0x8 */
+ pci_write_config_byte(pdev, PCI_CACHE_LINE_SIZE, 0x08);
+
+ /* Force latency timer to maximum setting so Cassini can
+ * sit on the bus as long as it likes.
+ */
+ pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0xff);
+}
+
static int __devinit cas_init_one(struct pci_dev *pdev,
const struct pci_device_id *ent)
{
printk(KERN_WARNING PFX "Could not enable MWI for %s\n",
pci_name(pdev));
+ cas_program_bridge(pdev);
+
/*
* On some architectures, the default cache line size set
* by pci_try_set_mwi reduces perforamnce. We have to increase
inserted into
outgoing frame. */
struct cas_tx_desc {
- u64 control;
- u64 buffer;
+ __le64 control;
+ __le64 buffer;
};
/* descriptor ring for free buffers contains page-sized buffers. the index
* the completion ring.
*/
struct cas_rx_desc {
- u64 index;
- u64 buffer;
+ __le64 index;
+ __le64 buffer;
};
/* received packets are put on the completion ring. */
#define RX_INDEX_RELEASE 0x0000000000002000ULL
struct cas_rx_comp {
- u64 word1;
- u64 word2;
- u64 word3;
- u64 word4;
+ __le64 word1;
+ __le64 word2;
+ __le64 word3;
+ __le64 word4;
};
enum link_state {
struct cas_rx_comp rxcs[N_RX_COMP_RINGS][INIT_BLOCK_RX_COMP];
struct cas_rx_desc rxds[N_RX_DESC_RINGS][INIT_BLOCK_RX_DESC];
struct cas_tx_desc txds[N_TX_RINGS][INIT_BLOCK_TX];
- u64 tx_compwb;
+ __le64 tx_compwb;
};
/* tiny buffers to deal with target abort issue. we allocate a bit
struct nic *nic = container_of(napi, struct nic, napi);
struct net_device *netdev = nic->netdev;
unsigned int work_done = 0;
- int tx_cleaned;
e100_rx_clean(nic, &work_done, budget);
- tx_cleaned = e100_tx_clean(nic);
+ e100_tx_clean(nic);
- /* If no Rx and Tx cleanup work was done, exit polling mode. */
- if((!tx_cleaned && (work_done == 0)) || !netif_running(netdev)) {
+ /* If budget not fully consumed, exit the polling mode */
+ if (work_done < budget) {
netif_rx_complete(netdev, napi);
e100_enable_irq(nic);
}
{
struct e1000_adapter *adapter = container_of(napi, struct e1000_adapter, napi);
struct net_device *poll_dev = adapter->netdev;
- int tx_cleaned = 0, work_done = 0;
+ int work_done = 0;
/* Must NOT use netdev_priv macro here. */
adapter = poll_dev->priv;
- /* Keep link state information with original netdev */
- if (!netif_carrier_ok(poll_dev))
- goto quit_polling;
-
/* e1000_clean is called per-cpu. This lock protects
* tx_ring[0] from being cleaned by multiple cpus
* simultaneously. A failure obtaining the lock means
* tx_ring[0] is currently being cleaned anyway. */
if (spin_trylock(&adapter->tx_queue_lock)) {
- tx_cleaned = e1000_clean_tx_irq(adapter,
- &adapter->tx_ring[0]);
+ e1000_clean_tx_irq(adapter,
+ &adapter->tx_ring[0]);
spin_unlock(&adapter->tx_queue_lock);
}
adapter->clean_rx(adapter, &adapter->rx_ring[0],
&work_done, budget);
- /* If no Tx and not enough Rx work done, exit the polling mode */
- if ((!tx_cleaned && (work_done == 0)) ||
- !netif_running(poll_dev)) {
-quit_polling:
+ /* If budget not fully consumed, exit the polling mode */
+ if (work_done < budget) {
if (likely(adapter->itr_setting & 3))
e1000_set_itr(adapter);
netif_rx_complete(poll_dev, napi);
{
struct e1000_adapter *adapter = container_of(napi, struct e1000_adapter, napi);
struct net_device *poll_dev = adapter->netdev;
- int tx_cleaned = 0, work_done = 0;
+ int work_done = 0;
/* Must NOT use netdev_priv macro here. */
adapter = poll_dev->priv;
- /* Keep link state information with original netdev */
- if (!netif_carrier_ok(poll_dev))
- goto quit_polling;
-
/* e1000_clean is called per-cpu. This lock protects
* tx_ring from being cleaned by multiple cpus
* simultaneously. A failure obtaining the lock means
* tx_ring is currently being cleaned anyway. */
if (spin_trylock(&adapter->tx_queue_lock)) {
- tx_cleaned = e1000_clean_tx_irq(adapter);
+ e1000_clean_tx_irq(adapter);
spin_unlock(&adapter->tx_queue_lock);
}
adapter->clean_rx(adapter, &work_done, budget);
- /* If no Tx and not enough Rx work done, exit the polling mode */
- if ((!tx_cleaned && (work_done < budget)) ||
- !netif_running(poll_dev)) {
-quit_polling:
+ /* If budget not fully consumed, exit the polling mode */
+ if (work_done < budget) {
if (adapter->itr_setting & 3)
e1000_set_itr(adapter);
netif_rx_complete(poll_dev, napi);
epic_rx_err(dev, ep);
- if (netif_running(dev) && (work_done < budget)) {
+ if (work_done < budget) {
unsigned long flags;
int more;
__u16 pkt_len, sc;
int curidx;
- if (fpi->use_napi) {
- if (!netif_running(dev))
- return 0;
- }
-
/*
* First, grab all of the stats for the incoming packet.
* These get messed up if we get called due to a busy condition.
dev->dev_addr[3] = (np->orig_mac[0] >> 16) & 0xff;
dev->dev_addr[4] = (np->orig_mac[0] >> 8) & 0xff;
dev->dev_addr[5] = (np->orig_mac[0] >> 0) & 0xff;
- /* set permanent address to be correct aswell */
- np->orig_mac[0] = (dev->dev_addr[0] << 0) + (dev->dev_addr[1] << 8) +
- (dev->dev_addr[2] << 16) + (dev->dev_addr[3] << 24);
- np->orig_mac[1] = (dev->dev_addr[4] << 0) + (dev->dev_addr[5] << 8);
writel(txreg|NVREG_TRANSMITPOLL_MAC_ADDR_REV, base + NvRegTransmitPoll);
}
memcpy(dev->perm_addr, dev->dev_addr, dev->addr_len);
*/
writel(np->orig_mac[0], base + NvRegMacAddrA);
writel(np->orig_mac[1], base + NvRegMacAddrB);
+ writel(readl(base + NvRegTransmitPoll) & ~NVREG_TRANSMITPOLL_MAC_ADDR_REV,
+ base + NvRegTransmitPoll);
/* free all structures */
free_rings(dev);
u16 pkt_len, sc;
int curidx;
- if (!netif_running(dev))
- return 0;
-
/*
* First, grab all of the stats for the incoming packet.
* These get messed up if we get called due to a busy condition.
{
struct ixgb_adapter *adapter = container_of(napi, struct ixgb_adapter, napi);
struct net_device *netdev = adapter->netdev;
- int tx_cleaned;
int work_done = 0;
- tx_cleaned = ixgb_clean_tx_irq(adapter);
+ ixgb_clean_tx_irq(adapter);
ixgb_clean_rx_irq(adapter, &work_done, budget);
- /* if no Tx and not enough Rx work done, exit the polling mode */
- if((!tx_cleaned && (work_done == 0)) || !netif_running(netdev)) {
+ /* If budget not fully consumed, exit the polling mode */
+ if (work_done < budget) {
netif_rx_complete(netdev, napi);
ixgb_irq_enable(adapter);
}
struct ixgbe_adapter *adapter = container_of(napi,
struct ixgbe_adapter, napi);
struct net_device *netdev = adapter->netdev;
- int tx_cleaned = 0, work_done = 0;
-
- /* Keep link state information with original netdev */
- if (!netif_carrier_ok(adapter->netdev))
- goto quit_polling;
+ int work_done = 0;
/* In non-MSIX case, there is no multi-Tx/Rx queue */
- tx_cleaned = ixgbe_clean_tx_irq(adapter, adapter->tx_ring);
+ ixgbe_clean_tx_irq(adapter, adapter->tx_ring);
ixgbe_clean_rx_irq(adapter, &adapter->rx_ring[0], &work_done,
budget);
- /* If no Tx and not enough Rx work done, exit the polling mode */
- if ((!tx_cleaned && (work_done < budget)) ||
- !netif_running(adapter->netdev)) {
-quit_polling:
+ /* If budget not fully consumed, exit the polling mode */
+ if (work_done < budget) {
netif_rx_complete(netdev, napi);
ixgbe_irq_enable(adapter);
}
struct net_device *dev = ip->dev;
int rx;
- /* @@@ Have to stop polling when nds[0] is administratively
- * downed while we are polling. */
rx = 0;
do {
ixp2000_reg_write(IXP2000_IRQ_THD_RAW_STATUS_A_0, 0x00ff);
{
int i;
DECLARE_MAC_BUF(mac);
+ u64 macaddr;
- for (i = 0; i < 6; i++)
- dev->dev_addr[i] = o2meth_eaddr[i];
DPRINTK("Loading MAC Address: %s\n", print_mac(mac, dev->dev_addr));
- mace->eth.mac_addr = (*(unsigned long*)o2meth_eaddr) >> 16;
+ macaddr = 0;
+ for (i = 0; i < 6; i++)
+ macaddr |= dev->dev_addr[i] << ((5 - i) * 8);
+
+ mace->eth.mac_addr = macaddr;
}
/*
#endif
dev->irq = MACE_ETHERNET_IRQ;
dev->base_addr = (unsigned long)&mace->eth;
+ memcpy(dev->dev_addr, o2meth_eaddr, 6);
priv = netdev_priv(dev);
spin_lock_init(&priv->meth_lock);
/* process as many rx events as NAPI will allow */
work_done = myri10ge_clean_rx_done(mgp, budget);
- if (work_done < budget || !netif_running(netdev)) {
+ if (work_done < budget) {
netif_rx_complete(netdev, napi);
put_be32(htonl(3), mgp->irq_claim);
}
/* Reenable interrupts providing nothing is trying to shut
* the chip down. */
spin_lock(&np->lock);
- if (!np->hands_off && netif_running(dev))
+ if (!np->hands_off)
natsemi_irq_enable(dev);
spin_unlock(&np->lock);
ndev->last_rx = jiffies;
skb->protocol = eth_type_trans(skb, ndev);
netif_rx(skb);
- dev->stats.rx_packets++;
- dev->stats.rx_bytes += len;
+ ndev->stats.rx_packets++;
+ ndev->stats.rx_bytes += len;
}
static irqreturn_t
budget / MAX_RCV_CTX);
}
- if (work_done >= budget && netxen_nic_rx_has_work(adapter) != 0)
+ if (work_done >= budget)
done = 0;
if (netxen_process_cmd_ring((unsigned long)adapter) == 0)
#define DRV_MODULE_NAME "niu"
#define PFX DRV_MODULE_NAME ": "
-#define DRV_MODULE_VERSION "0.5"
-#define DRV_MODULE_RELDATE "October 5, 2007"
+#define DRV_MODULE_VERSION "0.6"
+#define DRV_MODULE_RELDATE "January 5, 2008"
static char version[] __devinitdata =
DRV_MODULE_NAME ".c:v" DRV_MODULE_VERSION " (" DRV_MODULE_RELDATE ")\n";
skb->protocol = eth_type_trans(skb, np->dev);
netif_receive_skb(skb);
+ np->dev->last_rx = jiffies;
+
return num_rcr;
}
u64 stat = nr64(RX_DMA_CTL_STAT(rp->rx_channel));
int err = 0;
- dev_err(np->device, PFX "%s: RX channel %u error, stat[%llx]\n",
- np->dev->name, rp->rx_channel, (unsigned long long) stat);
-
- niu_log_rxchan_errors(np, rp, stat);
if (stat & (RX_DMA_CTL_STAT_CHAN_FATAL |
RX_DMA_CTL_STAT_PORT_FATAL))
err = -EINVAL;
+ if (err) {
+ dev_err(np->device, PFX "%s: RX channel %u error, stat[%llx]\n",
+ np->dev->name, rp->rx_channel,
+ (unsigned long long) stat);
+
+ niu_log_rxchan_errors(np, rp, stat);
+ }
+
nw64(RX_DMA_CTL_STAT(rp->rx_channel),
stat & RX_DMA_CTL_WRITE_CLEAR_ERRS);
return -ENODEV;
}
-static int niu_slowpath_interrupt(struct niu *np, struct niu_ldg *lp)
+static int niu_slowpath_interrupt(struct niu *np, struct niu_ldg *lp,
+ u64 v0, u64 v1, u64 v2)
{
- u64 v0 = lp->v0;
- u64 v1 = lp->v1;
- u64 v2 = lp->v2;
+
int i, err = 0;
+ lp->v0 = v0;
+ lp->v1 = v1;
+ lp->v2 = v2;
+
if (v1 & 0x00000000ffffffffULL) {
u32 rx_vec = (v1 & 0xffffffff);
if (rx_vec & (1 << rp->rx_channel)) {
int r = niu_rx_error(np, rp);
- if (r)
+ if (r) {
err = r;
+ } else {
+ if (!v0)
+ nw64(RX_DMA_CTL_STAT(rp->rx_channel),
+ RX_DMA_CTL_STAT_MEX);
+ }
}
}
}
if (err)
niu_enable_interrupts(np, 0);
- return -EINVAL;
+ return err;
}
static void niu_rxchan_intr(struct niu *np, struct rx_ring_info *rp,
}
if (unlikely((v0 & ((u64)1 << LDN_MIF)) || v1 || v2)) {
- int err = niu_slowpath_interrupt(np, lp);
+ int err = niu_slowpath_interrupt(np, lp, v0, v1, v2);
if (err)
goto out;
}
}
kfree_skb(skb);
skb = skb_new;
- }
+ } else
+ skb_orphan(skb);
align = ((unsigned long) skb->data & (16 - 1));
headroom = align + sizeof(struct tx_pkt_hdr);
{
#ifdef CONFIG_PCNET32_NAPI
struct pcnet32_private *lp = netdev_priv(dev);
+ ulong ioaddr = dev->base_addr;
+ u16 val;
#endif
netif_wake_queue(dev);
#ifdef CONFIG_PCNET32_NAPI
+ val = lp->a.read_csr(ioaddr, CSR3);
+ val &= 0x00ff;
+ lp->a.write_csr(ioaddr, CSR3, val);
napi_enable(&lp->napi);
#endif
}
unsigned long hw_flags;
struct ql3xxx_port_registers __iomem *port_regs = qdev->mem_map_registers;
- if (!netif_carrier_ok(ndev))
- goto quit_polling;
-
ql_tx_rx_clean(qdev, &tx_cleaned, &rx_cleaned, budget);
- if (tx_cleaned + rx_cleaned != budget ||
- !netif_running(ndev)) {
-quit_polling:
+ if (tx_cleaned + rx_cleaned != budget) {
spin_lock_irqsave(&qdev->hw_lock, hw_flags);
__netif_rx_complete(ndev, napi);
ql_update_small_bufq_prod_index(qdev);
rtl8169_irq_mask_and_ack(ioaddr);
#ifdef CONFIG_R8169_NAPI
+ tp->intr_mask = 0xffff;
+ RTL_W16(IntrMask, tp->intr_event);
napi_enable(&tp->napi);
#endif
}
struct XENA_dev_config __iomem *bar0 = nic->bar0;
int i;
- if (!is_s2io_card_up(nic))
- return 0;
-
mac_control = &nic->mac_control;
config = &nic->config;
TX_VLAN_TAG_OFF);
}
+ sky2_read32(hw, B0_Y2_SP_LISR);
napi_enable(&hw->napi);
netif_tx_unlock_bh(dev);
}
err = sky2_rx_start(sky2);
sky2_write32(hw, B0_IMSK, imask);
+ sky2_read32(hw, B0_Y2_SP_LISR);
napi_enable(&hw->napi);
if (err)
last = sky2_read16(hw, Y2_QADDR(rxqaddr[port], PREF_UNIT_PUT_IDX)),
sky2_read16(hw, Y2_QADDR(rxqaddr[port], PREF_UNIT_LAST_IDX)));
+ sky2_read32(hw, B0_Y2_SP_LISR);
napi_enable(&hw->napi);
return 0;
}
int received = 0;
#endif
- if (!netif_running(dev))
- goto done;
-
#ifdef CONFIG_TULIP_NAPI_HW_MITIGATION
/* that one buffer is needed for mit activation; or might be a
if (tulip_debug > 5)
printk(KERN_DEBUG "%s: In tulip_rx(), entry %d %8.8x.\n",
dev->name, entry, status);
- if (work_done++ >= budget)
+
+ if (++work_done >= budget)
goto not_done;
if ((status & 0x38008300) != 0x0300) {
* finally: amount of IO did not increase at all. */
} while ((ioread32(tp->base_addr + CSR5) & RxIntr));
-done:
-
#ifdef CONFIG_TULIP_NAPI_HW_MITIGATION
/* We use this simplistic scheme for IM. It's proven by
#define KAWETH_TX_TIMEOUT (5 * HZ)
#define KAWETH_SCRATCH_SIZE 32
#define KAWETH_FIRMWARE_BUF_SIZE 4096
-#define KAWETH_CONTROL_TIMEOUT (30 * HZ)
+#define KAWETH_CONTROL_TIMEOUT (30000)
#define KAWETH_STATUS_BROKEN 0x0000001
#define KAWETH_STATUS_CLOSING 0x0000002
ret = usb_control_msg(xdev, usb_rcvctrlpipe(xdev, 0), MCS7830_RD_BREQ,
MCS7830_RD_BMREQ, 0x0000, index, data,
- size, msecs_to_jiffies(MCS7830_CTRL_TIMEOUT));
+ size, MCS7830_CTRL_TIMEOUT);
return ret;
}
ret = usb_control_msg(xdev, usb_sndctrlpipe(xdev, 0), MCS7830_WR_BREQ,
MCS7830_WR_BMREQ, 0x0000, index, data,
- size, msecs_to_jiffies(MCS7830_CTRL_TIMEOUT));
+ size, MCS7830_CTRL_TIMEOUT);
return ret;
}
#define B43_PHYTYPE_A 0x00
#define B43_PHYTYPE_B 0x01
#define B43_PHYTYPE_G 0x02
+#define B43_PHYTYPE_N 0x04
+#define B43_PHYTYPE_LP 0x05
/* PHYRegisters */
#define B43_PHY_ILT_A_CTRL 0x0072
#define PAD_BYTES(nr_bytes) P4D_BYTES( __LINE__ , (nr_bytes))
/* Lightweight function to convert a frequency (in Mhz) to a channel number. */
-static inline u8 b43_freq_to_channel_a(int freq)
+static inline u8 b43_freq_to_channel_5ghz(int freq)
{
return ((freq - 5000) / 5);
}
-static inline u8 b43_freq_to_channel_bg(int freq)
+static inline u8 b43_freq_to_channel_2ghz(int freq)
{
u8 channel;
return channel;
}
-static inline u8 b43_freq_to_channel(struct b43_wldev *dev, int freq)
-{
- if (dev->phy.type == B43_PHYTYPE_A)
- return b43_freq_to_channel_a(freq);
- return b43_freq_to_channel_bg(freq);
-}
/* Lightweight function to convert a channel number to a frequency (in Mhz). */
-static inline int b43_channel_to_freq_a(u8 channel)
+static inline int b43_channel_to_freq_5ghz(u8 channel)
{
return (5000 + (5 * channel));
}
-static inline int b43_channel_to_freq_bg(u8 channel)
+static inline int b43_channel_to_freq_2ghz(u8 channel)
{
int freq;
return freq;
}
-static inline int b43_channel_to_freq(struct b43_wldev *dev, u8 channel)
-{
- if (dev->phy.type == B43_PHYTYPE_A)
- return b43_channel_to_freq_a(channel);
- return b43_channel_to_freq_bg(channel);
-}
static inline int b43_is_cck_rate(int rate)
{
switch (chanstat & B43_RX_CHAN_PHYTYPE) {
case B43_PHYTYPE_A:
status.phymode = MODE_IEEE80211A;
- status.freq = chanid;
- status.channel = b43_freq_to_channel_a(chanid);
- break;
- case B43_PHYTYPE_B:
- status.phymode = MODE_IEEE80211B;
- status.freq = chanid + 2400;
- status.channel = b43_freq_to_channel_bg(chanid + 2400);
+ B43_WARN_ON(1);
+ /* FIXME: We don't really know which value the "chanid" contains.
+ * So the following assignment might be wrong. */
+ status.channel = chanid;
+ status.freq = b43_channel_to_freq_5ghz(status.channel);
break;
case B43_PHYTYPE_G:
status.phymode = MODE_IEEE80211G;
+ /* chanid is the radio channel cookie value as used
+ * to tune the radio. */
status.freq = chanid + 2400;
- status.channel = b43_freq_to_channel_bg(chanid + 2400);
+ status.channel = b43_freq_to_channel_2ghz(status.freq);
+ break;
+ case B43_PHYTYPE_N:
+ status.phymode = 0xDEAD /*FIXME MODE_IEEE80211N*/;
+ /* chanid is the SHM channel cookie. Which is the plain
+ * channel number in b43. */
+ status.channel = chanid;
+ if (chanstat & B43_RX_CHAN_5GHZ)
+ status.freq = b43_freq_to_channel_5ghz(status.freq);
+ else
+ status.freq = b43_freq_to_channel_2ghz(status.freq);
break;
default:
B43_WARN_ON(1);
+ goto drop;
}
dev->stats.last_rx = jiffies;
} __attribute__ ((__packed__));
/* PHY RX Status 0 */
-#define B43_RX_PHYST0_GAINCTL 0x4000 /* Gain Control */
-#define B43_RX_PHYST0_PLCPHCF 0x0200
-#define B43_RX_PHYST0_PLCPFV 0x0100
-#define B43_RX_PHYST0_SHORTPRMBL 0x0080 /* Received with Short Preamble */
+#define B43_RX_PHYST0_GAINCTL 0x4000 /* Gain Control */
+#define B43_RX_PHYST0_PLCPHCF 0x0200
+#define B43_RX_PHYST0_PLCPFV 0x0100
+#define B43_RX_PHYST0_SHORTPRMBL 0x0080 /* Received with Short Preamble */
#define B43_RX_PHYST0_LCRS 0x0040
-#define B43_RX_PHYST0_ANT 0x0020 /* Antenna */
-#define B43_RX_PHYST0_UNSRATE 0x0010
+#define B43_RX_PHYST0_ANT 0x0020 /* Antenna */
+#define B43_RX_PHYST0_UNSRATE 0x0010
#define B43_RX_PHYST0_CLIP 0x000C
#define B43_RX_PHYST0_CLIP_SHIFT 2
-#define B43_RX_PHYST0_FTYPE 0x0003 /* Frame type */
-#define B43_RX_PHYST0_CCK 0x0000 /* Frame type: CCK */
-#define B43_RX_PHYST0_OFDM 0x0001 /* Frame type: OFDM */
-#define B43_RX_PHYST0_PRE_N 0x0002 /* Pre-standard N-PHY frame */
-#define B43_RX_PHYST0_STD_N 0x0003 /* Standard N-PHY frame */
+#define B43_RX_PHYST0_FTYPE 0x0003 /* Frame type */
+#define B43_RX_PHYST0_CCK 0x0000 /* Frame type: CCK */
+#define B43_RX_PHYST0_OFDM 0x0001 /* Frame type: OFDM */
+#define B43_RX_PHYST0_PRE_N 0x0002 /* Pre-standard N-PHY frame */
+#define B43_RX_PHYST0_STD_N 0x0003 /* Standard N-PHY frame */
/* PHY RX Status 2 */
-#define B43_RX_PHYST2_LNAG 0xC000 /* LNA Gain */
+#define B43_RX_PHYST2_LNAG 0xC000 /* LNA Gain */
#define B43_RX_PHYST2_LNAG_SHIFT 14
-#define B43_RX_PHYST2_PNAG 0x3C00 /* PNA Gain */
+#define B43_RX_PHYST2_PNAG 0x3C00 /* PNA Gain */
#define B43_RX_PHYST2_PNAG_SHIFT 10
-#define B43_RX_PHYST2_FOFF 0x03FF /* F offset */
+#define B43_RX_PHYST2_FOFF 0x03FF /* F offset */
/* PHY RX Status 3 */
-#define B43_RX_PHYST3_DIGG 0x1800 /* DIG Gain */
+#define B43_RX_PHYST3_DIGG 0x1800 /* DIG Gain */
#define B43_RX_PHYST3_DIGG_SHIFT 11
-#define B43_RX_PHYST3_TRSTATE 0x0400 /* TR state */
+#define B43_RX_PHYST3_TRSTATE 0x0400 /* TR state */
/* MAC RX Status */
-#define B43_RX_MAC_BEACONSENT 0x00008000 /* Beacon send flag */
-#define B43_RX_MAC_KEYIDX 0x000007E0 /* Key index */
-#define B43_RX_MAC_KEYIDX_SHIFT 5
-#define B43_RX_MAC_DECERR 0x00000010 /* Decrypt error */
-#define B43_RX_MAC_DEC 0x00000008 /* Decryption attempted */
-#define B43_RX_MAC_PADDING 0x00000004 /* Pad bytes present */
-#define B43_RX_MAC_RESP 0x00000002 /* Response frame transmitted */
-#define B43_RX_MAC_FCSERR 0x00000001 /* FCS error */
+#define B43_RX_MAC_RXST_VALID 0x01000000 /* PHY RXST valid */
+#define B43_RX_MAC_TKIP_MICERR 0x00100000 /* TKIP MIC error */
+#define B43_RX_MAC_TKIP_MICATT 0x00080000 /* TKIP MIC attempted */
+#define B43_RX_MAC_AGGTYPE 0x00060000 /* Aggregation type */
+#define B43_RX_MAC_AGGTYPE_SHIFT 17
+#define B43_RX_MAC_AMSDU 0x00010000 /* A-MSDU mask */
+#define B43_RX_MAC_BEACONSENT 0x00008000 /* Beacon sent flag */
+#define B43_RX_MAC_KEYIDX 0x000007E0 /* Key index */
+#define B43_RX_MAC_KEYIDX_SHIFT 5
+#define B43_RX_MAC_DECERR 0x00000010 /* Decrypt error */
+#define B43_RX_MAC_DEC 0x00000008 /* Decryption attempted */
+#define B43_RX_MAC_PADDING 0x00000004 /* Pad bytes present */
+#define B43_RX_MAC_RESP 0x00000002 /* Response frame transmitted */
+#define B43_RX_MAC_FCSERR 0x00000001 /* FCS error */
/* RX channel */
-#define B43_RX_CHAN_GAIN 0xFC00 /* Gain */
-#define B43_RX_CHAN_GAIN_SHIFT 10
-#define B43_RX_CHAN_ID 0x03FC /* Channel ID */
-#define B43_RX_CHAN_ID_SHIFT 2
-#define B43_RX_CHAN_PHYTYPE 0x0003 /* PHY type */
+#define B43_RX_CHAN_40MHZ 0x1000 /* 40 Mhz channel width */
+#define B43_RX_CHAN_5GHZ 0x0800 /* 5 Ghz band */
+#define B43_RX_CHAN_ID 0x07F8 /* Channel ID */
+#define B43_RX_CHAN_ID_SHIFT 3
+#define B43_RX_CHAN_PHYTYPE 0x0007 /* PHY type */
+
u8 b43_plcp_get_ratecode_cck(const u8 bitrate);
u8 b43_plcp_get_ratecode_ofdm(const u8 bitrate);
spin_lock(&np->rx_lock);
- if (unlikely(!netif_carrier_ok(dev))) {
- spin_unlock(&np->rx_lock);
- return 0;
- }
-
skb_queue_head_init(&rxq);
skb_queue_head_init(&errq);
skb_queue_head_init(&tmpq);
return child;
}
-static void pci_enable_crs(struct pci_dev *dev)
-{
- u16 cap, rpctl;
- int rpcap = pci_find_capability(dev, PCI_CAP_ID_EXP);
- if (!rpcap)
- return;
-
- pci_read_config_word(dev, rpcap + PCI_CAP_FLAGS, &cap);
- if (((cap & PCI_EXP_FLAGS_TYPE) >> 4) != PCI_EXP_TYPE_ROOT_PORT)
- return;
-
- pci_read_config_word(dev, rpcap + PCI_EXP_RTCTL, &rpctl);
- rpctl |= PCI_EXP_RTCTL_CRSSVE;
- pci_write_config_word(dev, rpcap + PCI_EXP_RTCTL, rpctl);
-}
-
static void pci_fixup_parent_subordinate_busnr(struct pci_bus *child, int max)
{
struct pci_bus *parent = child->parent;
pci_write_config_word(dev, PCI_BRIDGE_CONTROL,
bctl & ~PCI_BRIDGE_CTL_MASTER_ABORT);
- pci_enable_crs(dev);
-
if ((buses & 0xffff00) && !pcibios_assign_all_busses() && !is_cardbus) {
unsigned int cmax, busnr;
/*
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_0, quirk_ich6_lpc_acpi );
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_2, quirk_ich6_lpc_acpi );
DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_3, quirk_ich6_lpc_acpi );
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_1, quirk_ich6_lpc_acpi );
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH8_4, quirk_ich6_lpc_acpi );
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH9_2, quirk_ich6_lpc_acpi );
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH9_4, quirk_ich6_lpc_acpi );
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH9_7, quirk_ich6_lpc_acpi );
+DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_ICH9_8, quirk_ich6_lpc_acpi );
/*
* VIA ACPI: One IO region pointed to by longword at
int cnt;
int req_cnt;
int seg_cnt;
- dma_addr_t dma_handle;
u8 dir;
ENTER("qla1280_32bit_start_scsi");
cmd->cmnd[0]);
/* Calculate number of entries and segments required. */
+ req_cnt = 1;
seg_cnt = scsi_dma_map(cmd);
if (seg_cnt) {
/*
}
EXPORT_SYMBOL(scsi_prep_return);
-static int scsi_prep_fn(struct request_queue *q, struct request *req)
+int scsi_prep_fn(struct request_queue *q, struct request *req)
{
struct scsi_device *sdev = q->queuedata;
int ret = BLKPREP_KILL;
extern void scsi_free_queue(struct request_queue *q);
extern int scsi_init_queue(void);
extern void scsi_exit_queue(void);
+struct request_queue;
+struct request;
+extern int scsi_prep_fn(struct request_queue *, struct request *);
/* scsi_proc.c */
#ifdef CONFIG_SCSI_PROC_FS
return err;
}
+static int scsi_bus_remove(struct device *dev)
+{
+ struct device_driver *drv = dev->driver;
+ struct scsi_device *sdev = to_scsi_device(dev);
+ int err = 0;
+
+ /* reset the prep_fn back to the default since the
+ * driver may have altered it and it's being removed */
+ blk_queue_prep_rq(sdev->request_queue, scsi_prep_fn);
+
+ if (drv && drv->remove)
+ err = drv->remove(dev);
+
+ return 0;
+}
+
struct bus_type scsi_bus_type = {
.name = "scsi",
.match = scsi_bus_match,
.uevent = scsi_bus_uevent,
.suspend = scsi_bus_suspend,
.resume = scsi_bus_resume,
+ .remove = scsi_bus_remove,
};
int scsi_sysfs_register(void)
static int do_srp_rport_del(struct device *dev, void *data)
{
- srp_rport_del(dev_to_rport(dev));
+ if (scsi_is_srp_rport(dev))
+ srp_rport_del(dev_to_rport(dev));
return 0;
}
}
EXPORT_SYMBOL(sunserial_unregister_minors);
-int __init sunserial_console_match(struct console *con, struct device_node *dp,
+int sunserial_console_match(struct console *con, struct device_node *dp,
struct uart_driver *drv, int line)
{
int off;
struct spi_bitbang_cs *cs = spi->controller_state;
struct spi_bitbang *bitbang;
int retval;
+ unsigned long flags;
bitbang = spi_master_get_devdata(spi->master);
*/
/* deselect chip (low or high) */
- spin_lock(&bitbang->lock);
+ spin_lock_irqsave(&bitbang->lock, flags);
if (!bitbang->busy) {
bitbang->chipselect(spi, BITBANG_CS_INACTIVE);
ndelay(cs->nsecs);
}
- spin_unlock(&bitbang->lock);
+ spin_unlock_irqrestore(&bitbang->lock, flags);
return 0;
}
case SSB_DEV_PCI:
case SSB_DEV_PCIE:
#ifdef CONFIG_SSB_DRIVER_PCICORE
+ if (bus->bustype == SSB_BUSTYPE_PCI) {
+ /* Ignore PCI cores on PCI-E cards.
+ * Ignore PCI-E cores on PCI cards. */
+ if (dev->id.coreid == SSB_DEV_PCI) {
+ if (bus->host_pci->is_pcie)
+ continue;
+ } else {
+ if (!bus->host_pci->is_pcie)
+ continue;
+ }
+ }
if (bus->pcicore.dev) {
ssb_printk(KERN_WARNING PFX
"WARNING: Multiple PCI(E) cores found\n");
}
spin_unlock_irqrestore(&priv->lock, flags);
+ /* The PL2303 is reported to lose bytes if you change
+ serial settings even to the same values as before. Thus
+ we actually need to filter in this specific case */
+
+ if (!tty_termios_hw_change(port->tty->termios, old_termios))
+ return;
+
cflag = port->tty->termios->c_cflag;
buf = kzalloc(7, GFP_KERNEL);
prstatus->pr_sigpend = p->pending.signal.sig[0];
prstatus->pr_sighold = p->blocked.sig[0];
prstatus->pr_pid = task_pid_vnr(p);
- prstatus->pr_ppid = task_pid_vnr(p->parent);
+ prstatus->pr_ppid = task_pid_vnr(p->real_parent);
prstatus->pr_pgrp = task_pgrp_vnr(p);
prstatus->pr_sid = task_session_vnr(p);
if (thread_group_leader(p)) {
psinfo->pr_psargs[len] = 0;
psinfo->pr_pid = task_pid_vnr(p);
- psinfo->pr_ppid = task_pid_vnr(p->parent);
+ psinfo->pr_ppid = task_pid_vnr(p->real_parent);
psinfo->pr_pgrp = task_pgrp_vnr(p);
psinfo->pr_sid = task_session_vnr(p);
* ioctls.
*/
+#include <linux/joystick.h>
+
#include <linux/types.h>
#include <linux/compat.h>
#include <linux/kernel.h>
COMPATIBLE_IOCTL(VIDEO_GET_SIZE)
COMPATIBLE_IOCTL(VIDEO_GET_FRAME_RATE)
+/* joystick */
+COMPATIBLE_IOCTL(JSIOCGVERSION)
+COMPATIBLE_IOCTL(JSIOCGAXES)
+COMPATIBLE_IOCTL(JSIOCGBUTTONS)
+COMPATIBLE_IOCTL(JSIOCGNAME(0))
+
/* now things that need handlers */
HANDLE_IOCTL(MEMREADOOB32, mtd_rw_oob)
HANDLE_IOCTL(MEMWRITEOOB32, mtd_rw_oob)
rc = ecryptfs_create_underlying_file(lower_dir_dentry->d_inode,
ecryptfs_dentry, mode, nd);
if (rc) {
- struct inode *ecryptfs_inode = ecryptfs_dentry->d_inode;
- struct ecryptfs_inode_info *inode_info =
- ecryptfs_inode_to_private(ecryptfs_inode);
-
- printk(KERN_WARNING "%s: Error creating underlying file; "
- "rc = [%d]; checking for existing\n", __FUNCTION__, rc);
- if (inode_info) {
- mutex_lock(&inode_info->lower_file_mutex);
- if (!inode_info->lower_file) {
- mutex_unlock(&inode_info->lower_file_mutex);
- printk(KERN_ERR "%s: Failure to set underlying "
- "file; rc = [%d]\n", __FUNCTION__, rc);
- goto out_lock;
- }
- mutex_unlock(&inode_info->lower_file_mutex);
- }
+ printk(KERN_ERR "%s: Failure to create dentry in lower fs; "
+ "rc = [%d]\n", __FUNCTION__, rc);
+ goto out_lock;
}
rc = ecryptfs_interpose(lower_dentry, ecryptfs_dentry,
directory_inode->i_sb, 0);
dentry->d_inode->i_nlink =
ecryptfs_inode_to_lower(dentry->d_inode)->i_nlink;
dentry->d_inode->i_ctime = dir->i_ctime;
+ d_drop(dentry);
out_unlock:
unlock_parent(lower_dentry);
return rc;
fput(inode_info->lower_file);
inode_info->lower_file = NULL;
d_drop(lower_dentry);
- d_delete(lower_dentry);
}
}
mutex_unlock(&inode_info->lower_file_mutex);
EXPORT_SYMBOL_GPL(fat_free_clusters);
+/* 128kb is the whole sectors for FAT12 and FAT16 */
+#define FAT_READA_SIZE (128 * 1024)
+
+static void fat_ent_reada(struct super_block *sb, struct fat_entry *fatent,
+ unsigned long reada_blocks)
+{
+ struct fatent_operations *ops = MSDOS_SB(sb)->fatent_ops;
+ sector_t blocknr;
+ int i, offset;
+
+ ops->ent_blocknr(sb, fatent->entry, &offset, &blocknr);
+
+ for (i = 0; i < reada_blocks; i++)
+ sb_breadahead(sb, blocknr + i);
+}
+
int fat_count_free_clusters(struct super_block *sb)
{
struct msdos_sb_info *sbi = MSDOS_SB(sb);
struct fatent_operations *ops = sbi->fatent_ops;
struct fat_entry fatent;
+ unsigned long reada_blocks, reada_mask, cur_block;
int err = 0, free;
lock_fat(sbi);
if (sbi->free_clusters != -1)
goto out;
+ reada_blocks = FAT_READA_SIZE >> sb->s_blocksize_bits;
+ reada_mask = reada_blocks - 1;
+ cur_block = 0;
+
free = 0;
fatent_init(&fatent);
fatent_set_entry(&fatent, FAT_START_ENT);
while (fatent.entry < sbi->max_cluster) {
+ /* readahead of fat blocks */
+ if ((cur_block & reada_mask) == 0) {
+ unsigned long rest = sbi->fat_length - cur_block;
+ fat_ent_reada(sb, &fatent, min(reada_blocks, rest));
+ }
+ cur_block++;
+
err = fat_ent_read_block(sb, &fatent);
if (err)
goto out;
rec = (e + b) / 2;
len = hfs_brec_lenoff(bnode, rec, &off);
keylen = hfs_brec_keylen(bnode, rec);
+ if (keylen == HFS_BAD_KEYLEN) {
+ res = -EINVAL;
+ goto done;
+ }
hfs_bnode_read(bnode, fd->key, off, keylen);
cmpval = bnode->tree->keycmp(fd->key, fd->search_key);
if (!cmpval) {
if (rec != e && e >= 0) {
len = hfs_brec_lenoff(bnode, e, &off);
keylen = hfs_brec_keylen(bnode, e);
+ if (keylen == HFS_BAD_KEYLEN) {
+ res = -EINVAL;
+ goto done;
+ }
hfs_bnode_read(bnode, fd->key, off, keylen);
}
done:
len = hfs_brec_lenoff(bnode, fd->record, &off);
keylen = hfs_brec_keylen(bnode, fd->record);
+ if (keylen == HFS_BAD_KEYLEN) {
+ res = -EINVAL;
+ goto out;
+ }
fd->keyoffset = off;
fd->keylength = keylen;
fd->entryoffset = off + keylen;
recoff = hfs_bnode_read_u16(node, node->tree->node_size - (rec + 1) * 2);
if (!recoff)
return 0;
- if (node->tree->attributes & HFS_TREE_BIGKEYS)
+ if (node->tree->attributes & HFS_TREE_BIGKEYS) {
retval = hfs_bnode_read_u16(node, recoff) + 2;
- else
+ if (retval > node->tree->max_key_len + 2) {
+ printk(KERN_ERR "hfs: keylen %d too large\n",
+ retval);
+ retval = HFS_BAD_KEYLEN;
+ }
+ } else {
retval = (hfs_bnode_read_u8(node, recoff) | 1) + 1;
+ if (retval > node->tree->max_key_len + 1) {
+ printk(KERN_ERR "hfs: keylen %d too large\n",
+ retval);
+ retval = HFS_BAD_KEYLEN;
+ }
+ }
}
return retval;
}
goto fail_page;
if (!tree->node_count)
goto fail_page;
+ if ((id == HFS_EXT_CNID) && (tree->max_key_len != HFS_MAX_EXT_KEYLEN)) {
+ printk(KERN_ERR "hfs: invalid extent max_key_len %d\n",
+ tree->max_key_len);
+ goto fail_page;
+ }
+ if ((id == HFS_CAT_CNID) && (tree->max_key_len != HFS_MAX_CAT_KEYLEN)) {
+ printk(KERN_ERR "hfs: invalid catalog max_key_len %d\n",
+ tree->max_key_len);
+ goto fail_page;
+ }
+
tree->node_size_shift = ffs(size) - 1;
tree->pages_per_bnode = (tree->node_size + PAGE_CACHE_SIZE - 1) >> PAGE_CACHE_SHIFT;
return tree;
fail_page:
- tree->inode->i_mapping->a_ops = &hfs_aops;
page_cache_release(page);
free_tree:
+ tree->inode->i_mapping->a_ops = &hfs_aops;
iput(tree->inode);
kfree(tree);
return NULL;
#define HFS_MAX_NAMELEN 128
#define HFS_MAX_VALENCE 32767U
+#define HFS_BAD_KEYLEN 0xFF
+
/* Meanings of the drAtrb field of the MDB,
* Reference: _Inside Macintosh: Files_ p. 2-61
*/
struct hfs_ext_key ext;
} hfs_btree_key;
+#define HFS_MAX_CAT_KEYLEN (sizeof(struct hfs_cat_key) - sizeof(u8))
+#define HFS_MAX_EXT_KEYLEN (sizeof(struct hfs_ext_key) - sizeof(u8))
+
typedef union hfs_btree_key btree_key;
struct hfs_extent {
#define NFS_LOCK_INITIALIZED 1
int ls_flags;
struct nfs_seqid_counter ls_seqid;
+ struct rpc_sequence ls_sequence;
struct nfs_unique_id ls_id;
nfs4_stateid ls_stateid;
atomic_t ls_count;
if (data->rpc_status == 0) {
memcpy(data->o_res.stateid.data, data->c_res.stateid.data,
sizeof(data->o_res.stateid.data));
+ nfs_confirm_seqid(&data->owner->so_seqid, 0);
renew_lease(data->o_res.server, data->timestamp);
data->rpc_done = 1;
}
- nfs_confirm_seqid(&data->owner->so_seqid, data->rpc_status);
nfs_increment_open_seqid(data->rpc_status, data->c_arg.seqid);
}
/* In case of error, no cleanup! */
if (!data->rpc_done)
goto out_free;
- nfs_confirm_seqid(&data->owner->so_seqid, 0);
state = nfs4_opendata_to_nfs4_state(data);
if (!IS_ERR(state))
nfs4_close_state(&data->path, state, data->o_arg.open_flags);
/* In case we need an open_confirm, no cleanup! */
if (data->o_res.rflags & NFS4_OPEN_RESULT_CONFIRM)
goto out_free;
- nfs_confirm_seqid(&data->owner->so_seqid, 0);
state = nfs4_opendata_to_nfs4_state(data);
if (!IS_ERR(state))
nfs4_close_state(&data->path, state, data->o_arg.open_flags);
p->arg.fh = NFS_FH(inode);
p->arg.fl = &p->fl;
+ if (!(lsp->ls_seqid.flags & NFS_SEQID_CONFIRMED)) {
+ p->arg.open_seqid = nfs_alloc_seqid(&lsp->ls_state->owner->so_seqid);
+ if (p->arg.open_seqid == NULL)
+ goto out_free;
+
+ }
p->arg.lock_seqid = nfs_alloc_seqid(&lsp->ls_seqid);
if (p->arg.lock_seqid == NULL)
goto out_free;
memcpy(&p->fl, fl, sizeof(p->fl));
return p;
out_free:
+ if (p->arg.open_seqid != NULL)
+ nfs_free_seqid(p->arg.open_seqid);
kfree(p);
return NULL;
}
.rpc_cred = sp->so_cred,
};
- if (nfs_wait_on_sequence(data->arg.lock_seqid, task) != 0)
- return;
dprintk("%s: begin!\n", __FUNCTION__);
/* Do we need to do an open_to_lock_owner? */
if (!(data->arg.lock_seqid->sequence->flags & NFS_SEQID_CONFIRMED)) {
- data->arg.open_seqid = nfs_alloc_seqid(&sp->so_seqid);
- if (data->arg.open_seqid == NULL) {
- data->rpc_status = -ENOMEM;
- task->tk_action = NULL;
- goto out;
- }
+ if (nfs_wait_on_sequence(data->arg.open_seqid, task) != 0)
+ return;
data->arg.open_stateid = &state->stateid;
data->arg.new_lock_owner = 1;
+ /* Retest in case we raced... */
+ if (!(data->arg.lock_seqid->sequence->flags & NFS_SEQID_CONFIRMED))
+ goto do_rpc;
}
+ if (nfs_wait_on_sequence(data->arg.lock_seqid, task) != 0)
+ return;
+ data->arg.new_lock_owner = 0;
+do_rpc:
data->timestamp = jiffies;
rpc_call_setup(task, &msg, 0);
-out:
dprintk("%s: done!, ret = %d\n", __FUNCTION__, data->rpc_status);
}
struct nfs4_lockdata *data = calldata;
dprintk("%s: begin!\n", __FUNCTION__);
- if (data->arg.open_seqid != NULL)
- nfs_free_seqid(data->arg.open_seqid);
if (data->cancelled != 0) {
struct rpc_task *task;
task = nfs4_do_unlck(&data->fl, data->ctx, data->lsp,
dprintk("%s: cancelling lock!\n", __FUNCTION__);
} else
nfs_free_seqid(data->arg.lock_seqid);
+ if (data->arg.open_seqid != NULL)
+ nfs_free_seqid(data->arg.open_seqid);
nfs4_put_lock_state(data->lsp);
put_nfs_open_context(data->ctx);
kfree(data);
void
nfs4_kill_renewd(struct nfs_client *clp)
{
- down_read(&clp->cl_sem);
cancel_delayed_work_sync(&clp->cl_renewd);
- up_read(&clp->cl_sem);
}
/*
lsp = kzalloc(sizeof(*lsp), GFP_KERNEL);
if (lsp == NULL)
return NULL;
- lsp->ls_seqid.sequence = &state->owner->so_sequence;
+ rpc_init_wait_queue(&lsp->ls_sequence.wait, "lock_seqid_waitqueue");
+ spin_lock_init(&lsp->ls_sequence.lock);
+ INIT_LIST_HEAD(&lsp->ls_sequence.list);
+ lsp->ls_seqid.sequence = &lsp->ls_sequence;
atomic_set(&lsp->ls_count, 1);
lsp->ls_owner = fl_owner;
spin_lock(&clp->cl_lock);
error = PTR_ERR(mntroot);
goto error_splat_super;
}
- if (mntroot->d_inode->i_op != server->nfs_client->rpc_ops->dir_inode_ops) {
+ if (mntroot->d_inode->i_op != NFS_SB(s)->nfs_client->rpc_ops->dir_inode_ops) {
dput(mntroot);
error = -ESTALE;
goto error_splat_super;
error = PTR_ERR(mntroot);
goto error_splat_super;
}
+ if (mntroot->d_inode->i_op != NFS_SB(s)->nfs_client->rpc_ops->dir_inode_ops) {
+ dput(mntroot);
+ error = -ESTALE;
+ goto error_splat_super;
+ }
s->s_flags |= MS_ACTIVE;
mnt->mnt_sb = s;
error = PTR_ERR(mntroot);
goto error_splat_super;
}
+ if (mntroot->d_inode->i_op != NFS_SB(s)->nfs_client->rpc_ops->dir_inode_ops) {
+ dput(mntroot);
+ error = -ESTALE;
+ goto error_splat_super;
+ }
s->s_flags |= MS_ACTIVE;
mnt->mnt_sb = s;
(task->state == TASK_STOPPED || task->state == TASK_TRACED) && \
security_ptrace(current,task) == 0))
+struct mm_struct *mm_for_maps(struct task_struct *task)
+{
+ struct mm_struct *mm = get_task_mm(task);
+ if (!mm)
+ return NULL;
+ down_read(&mm->mmap_sem);
+ task_lock(task);
+ if (task->mm != mm)
+ goto out;
+ if (task->mm != current->mm && __ptrace_may_attach(task) < 0)
+ goto out;
+ task_unlock(task);
+ return mm;
+out:
+ task_unlock(task);
+ up_read(&mm->mmap_sem);
+ mmput(mm);
+ return NULL;
+}
+
static int proc_pid_cmdline(struct task_struct *task, char * buffer)
{
int res = 0;
unsigned long largest_chunk;
};
+extern struct mm_struct *mm_for_maps(struct task_struct *);
+
#ifdef CONFIG_MMU
#define VMALLOC_TOTAL (VMALLOC_END - VMALLOC_START)
extern void get_vmalloc_info(struct vmalloc_info *vmi);
};
#endif
-#ifdef CONFIG_SLAB
+#ifdef CONFIG_SLABINFO
static int slabinfo_open(struct inode *inode, struct file *file)
{
return seq_open(file, &slabinfo_op);
#endif
create_seq_entry("stat", 0, &proc_stat_operations);
create_seq_entry("interrupts", 0, &proc_interrupts_operations);
-#ifdef CONFIG_SLAB
+#ifdef CONFIG_SLABINFO
create_seq_entry("slabinfo",S_IWUSR|S_IRUGO,&proc_slabinfo_operations);
#ifdef CONFIG_DEBUG_SLAB_LEAK
create_seq_entry("slab_allocators", 0 ,&proc_slabstats_operations);
if (!priv->task)
return NULL;
- mm = get_task_mm(priv->task);
+ mm = mm_for_maps(priv->task);
if (!mm)
return NULL;
priv->tail_vma = tail_vma = get_gate_vma(priv->task);
- down_read(&mm->mmap_sem);
/* Start with last addr hint */
if (last_addr && (vma = find_vma(mm, last_addr))) {
if (!priv->task)
return NULL;
- mm = get_task_mm(priv->task);
+ mm = mm_for_maps(priv->task);
if (!mm) {
put_task_struct(priv->task);
priv->task = NULL;
return NULL;
}
- down_read(&mm->mmap_sem);
-
/* start from the Nth VMA */
for (vml = mm->context.vmlist; vml; vml = vml->next)
if (n-- == 0)
static inline enum xpc_retval
xpc_map_bte_errors(bte_result_t error)
{
+ if (error == BTE_SUCCESS)
+ return xpcSuccess;
+
if (is_shub2()) {
if (BTE_VALID_SH2_ERROR(error))
return xpcBteSh2Start + error;
- else
- return xpcBteUnmappedError;
+ return xpcBteUnmappedError;
}
switch (error) {
case BTE_SUCCESS: return xpcSuccess;
__u32 __user *ustatus);
int (*coredump_extra_notes_size)(void);
int (*coredump_extra_notes_write)(struct file *file, loff_t *foffset);
+ void (*notify_spus_active)(void);
struct module *owner;
};
int spu_switch_event_register(struct notifier_block * n);
int spu_switch_event_unregister(struct notifier_block * n);
+extern void notify_spus_active(void);
+extern void do_notify_spus_active(void);
+
/*
* This defines the Local Store, Problem Area and Privlege Area of an SPU.
*/
} v;
v.u = val;
#ifdef CONFIG_X86_BSWAP
- asm("bswapl %0 ; bswapl %1 ; xchgl %0,%1"
+ __asm__("bswapl %0 ; bswapl %1 ; xchgl %0,%1"
: "=r" (v.s.a), "=r" (v.s.b)
: "0" (v.s.a), "1" (v.s.b));
#else
v.s.a = ___arch__swab32(v.s.a);
v.s.b = ___arch__swab32(v.s.b);
- asm("xchgl %0,%1" : "=r" (v.s.a), "=r" (v.s.b) : "0" (v.s.a), "1" (v.s.b));
+ __asm__("xchgl %0,%1" : "=r" (v.s.a), "=r" (v.s.b) : "0" (v.s.a), "1" (v.s.b));
#endif
return v.u;
}
#define wrmsrl(msr,val) wrmsr(msr,(__u32)((__u64)(val)),((__u64)(val))>>32)
-/* wrmsr with exception handling */
-#define wrmsr_safe(msr,a,b) ({ int ret__; \
- asm volatile("2: wrmsr ; xorl %0,%0\n" \
- "1:\n\t" \
- ".section .fixup,\"ax\"\n\t" \
- "3: movl %4,%0 ; jmp 1b\n\t" \
- ".previous\n\t" \
- ".section __ex_table,\"a\"\n" \
- " .align 8\n\t" \
- " .quad 2b,3b\n\t" \
- ".previous" \
- : "=a" (ret__) \
- : "c" (msr), "0" (a), "d" (b), "i" (-EFAULT)); \
- ret__; })
-
-#define checking_wrmsrl(msr,val) wrmsr_safe(msr,(u32)(val),(u32)((val)>>32))
-
-#define rdmsr_safe(msr,a,b) \
- ({ int ret__; \
- asm volatile ("1: rdmsr\n" \
- "2:\n" \
- ".section .fixup,\"ax\"\n" \
- "3: movl %4,%0\n" \
- " jmp 2b\n" \
- ".previous\n" \
- ".section __ex_table,\"a\"\n" \
- " .align 8\n" \
- " .quad 1b,3b\n" \
- ".previous":"=&bDS" (ret__), "=a"(*(a)), "=d"(*(b)) \
- :"c"(msr), "i"(-EIO), "0"(0)); \
- ret__; })
-
#define rdtsc(low,high) \
__asm__ __volatile__("rdtsc" : "=a" (low), "=d" (high))
__asm__ __volatile__ ("rdtsc" : "=a" (low) : : "edx")
#define rdtscp(low,high,aux) \
- asm volatile (".byte 0x0f,0x01,0xf9" : "=a" (low), "=d" (high), "=c" (aux))
+ __asm__ __volatile__ (".byte 0x0f,0x01,0xf9" : "=a" (low), "=d" (high), "=c" (aux))
#define rdtscll(val) do { \
unsigned int __a,__d; \
- asm volatile("rdtsc" : "=a" (__a), "=d" (__d)); \
+ __asm__ __volatile__("rdtsc" : "=a" (__a), "=d" (__d)); \
(val) = ((unsigned long)__a) | (((unsigned long)__d)<<32); \
} while(0)
#define rdtscpll(val, aux) do { \
unsigned long __a, __d; \
- asm volatile (".byte 0x0f,0x01,0xf9" : "=a" (__a), "=d" (__d), "=c" (aux)); \
+ __asm__ __volatile__ (".byte 0x0f,0x01,0xf9" : "=a" (__a), "=d" (__d), "=c" (aux)); \
(val) = (__d << 32) | __a; \
} while (0)
: "=a" (low), "=d" (high) \
: "c" (counter))
+
static inline void cpuid(int op, unsigned int *eax, unsigned int *ebx,
unsigned int *ecx, unsigned int *edx)
{
return edx;
}
+#ifdef __KERNEL__
+
+/* wrmsr with exception handling */
+#define wrmsr_safe(msr,a,b) ({ int ret__; \
+ asm volatile("2: wrmsr ; xorl %0,%0\n" \
+ "1:\n\t" \
+ ".section .fixup,\"ax\"\n\t" \
+ "3: movl %4,%0 ; jmp 1b\n\t" \
+ ".previous\n\t" \
+ ".section __ex_table,\"a\"\n" \
+ " .align 8\n\t" \
+ " .quad 2b,3b\n\t" \
+ ".previous" \
+ : "=a" (ret__) \
+ : "c" (msr), "0" (a), "d" (b), "i" (-EFAULT)); \
+ ret__; })
+
+#define checking_wrmsrl(msr,val) wrmsr_safe(msr,(u32)(val),(u32)((val)>>32))
+
+#define rdmsr_safe(msr,a,b) \
+ ({ int ret__; \
+ asm volatile ("1: rdmsr\n" \
+ "2:\n" \
+ ".section .fixup,\"ax\"\n" \
+ "3: movl %4,%0\n" \
+ " jmp 2b\n" \
+ ".previous\n" \
+ ".section __ex_table,\"a\"\n" \
+ " .align 8\n" \
+ " .quad 1b,3b\n" \
+ ".previous":"=&bDS" (ret__), "=a"(*(a)), "=d"(*(b)) \
+ :"c"(msr), "i"(-EIO), "0"(0)); \
+ ret__; })
+
#ifdef CONFIG_SMP
void rdmsr_on_cpu(unsigned int cpu, u32 msr_no, u32 *l, u32 *h);
void wrmsr_on_cpu(unsigned int cpu, u32 msr_no, u32 l, u32 h);
return wrmsr_safe(msr_no, l, h);
}
#endif /* CONFIG_SMP */
+#endif /* __KERNEL__ */
#endif /* __ASSEMBLY__ */
#endif /* !__i386__ */
#define register_hotcpu_notifier(nb) register_cpu_notifier(nb)
#define unregister_hotcpu_notifier(nb) unregister_cpu_notifier(nb)
int cpu_down(unsigned int cpu);
-#define cpu_is_offline(cpu) unlikely(!cpu_online(cpu))
#else /* CONFIG_HOTPLUG_CPU */
/* These aren't inline functions due to a GCC bug. */
#define register_hotcpu_notifier(nb) ({ (void)(nb); 0; })
#define unregister_hotcpu_notifier(nb) ({ (void)(nb); })
-
-/* CPUs don't go offline once they're online w/o CONFIG_HOTPLUG_CPU */
-static inline int cpu_is_offline(int cpu) { return 0; }
#endif /* CONFIG_HOTPLUG_CPU */
#ifdef CONFIG_PM_SLEEP_SMP
#define cpu_present(cpu) ((cpu) == 0)
#endif
+#define cpu_is_offline(cpu) unlikely(!cpu_online(cpu))
+
#ifdef CONFIG_SMP
extern int nr_cpu_ids;
#define any_online_cpu(mask) __any_online_cpu(&(mask))
#define key_get(k) ({ NULL; })
#define key_put(k) do { } while(0)
#define key_ref_put(k) do { } while(0)
-#define make_key_ref(k) ({ NULL; })
+#define make_key_ref(k, p) ({ NULL; })
#define key_ref_to_ptr(k) ({ NULL; })
#define is_key_possessed(k) 0
#define alloc_uid_keyring(u,c) 0
enum
{
NAPI_STATE_SCHED, /* Poll is scheduled */
+ NAPI_STATE_DISABLE, /* Disable pending */
};
extern void FASTCALL(__napi_schedule(struct napi_struct *n));
+static inline int napi_disable_pending(struct napi_struct *n)
+{
+ return test_bit(NAPI_STATE_DISABLE, &n->state);
+}
+
/**
* napi_schedule_prep - check if napi can be scheduled
* @n: napi context
*
* Test if NAPI routine is already running, and if not mark
* it as running. This is used as a condition variable
- * insure only one NAPI poll instance runs
+ * insure only one NAPI poll instance runs. We also make
+ * sure there is no pending NAPI disable.
*/
static inline int napi_schedule_prep(struct napi_struct *n)
{
- return !test_and_set_bit(NAPI_STATE_SCHED, &n->state);
+ return !napi_disable_pending(n) &&
+ !test_and_set_bit(NAPI_STATE_SCHED, &n->state);
}
/**
*/
static inline void napi_disable(struct napi_struct *n)
{
+ set_bit(NAPI_STATE_DISABLE, &n->state);
while (test_and_set_bit(NAPI_STATE_SCHED, &n->state))
msleep(1);
+ clear_bit(NAPI_STATE_DISABLE, &n->state);
}
/**
static inline int netif_rx_schedule_prep(struct net_device *dev,
struct napi_struct *napi)
{
- return netif_running(dev) && napi_schedule_prep(napi);
+ return napi_schedule_prep(napi);
}
/* Add interface to tail of rx poll list. This assumes that _prep has
static inline void __netif_rx_schedule(struct net_device *dev,
struct napi_struct *napi)
{
- dev_hold(dev);
__napi_schedule(napi);
}
struct napi_struct *napi)
{
__napi_complete(napi);
- dev_put(dev);
}
/* Remove interface from poll list: it must be in the poll list
#define PCI_DEVICE_ID_INTEL_ICH9_4 0x2914
#define PCI_DEVICE_ID_INTEL_ICH9_5 0x2919
#define PCI_DEVICE_ID_INTEL_ICH9_6 0x2930
+#define PCI_DEVICE_ID_INTEL_ICH9_7 0x2916
+#define PCI_DEVICE_ID_INTEL_ICH9_8 0x2918
#define PCI_DEVICE_ID_INTEL_82855PM_HB 0x3340
#define PCI_DEVICE_ID_INTEL_82830_HB 0x3575
#define PCI_DEVICE_ID_INTEL_82830_CGC 0x3577
device_set_wakeup_enable(dev,val); \
} while(0)
+/*
+ * Global Power Management flags
+ * Used to keep APM and ACPI from both being active
+ */
+extern unsigned int pm_flags;
+
+#define PM_APM 1
+#define PM_ACPI 2
+
#endif /* __KERNEL__ */
#endif /* _LINUX_PM_H */
#ifdef CONFIG_PM_LEGACY
-extern int pm_active;
-
-#define PM_IS_ACTIVE() (pm_active != 0)
-
/*
* Register a device with power management
*/
#else /* CONFIG_PM_LEGACY */
-#define PM_IS_ACTIVE() 0
-
static inline struct pm_dev *pm_register(pm_dev_t type,
unsigned long id,
pm_callback callback)
extern void __ptrace_unlink(struct task_struct *child);
extern void ptrace_untrace(struct task_struct *child);
extern int ptrace_may_attach(struct task_struct *task);
+extern int __ptrace_may_attach(struct task_struct *task);
static inline void ptrace_link(struct task_struct *child,
struct task_struct *new_parent)
return kmalloc(size, flags | __GFP_ZERO);
}
+#ifdef CONFIG_SLABINFO
+extern const struct seq_operations slabinfo_op;
+ssize_t slabinfo_write(struct file *, const char __user *, size_t, loff_t *);
+#endif
+
#endif /* __KERNEL__ */
#endif /* _LINUX_SLAB_H */
#endif /* CONFIG_NUMA */
-extern const struct seq_operations slabinfo_op;
-ssize_t slabinfo_write(struct file *, const char __user *, size_t, loff_t *);
-
#endif /* _LINUX_SLAB_DEF_H */
extern void tty_termios_encode_baud_rate(struct ktermios *termios, speed_t ibaud, speed_t obaud);
extern void tty_encode_baud_rate(struct tty_struct *tty, speed_t ibaud, speed_t obaud);
extern void tty_termios_copy_hw(struct ktermios *new, struct ktermios *old);
+extern int tty_termios_hw_change(struct ktermios *a, struct ktermios *b);
extern struct tty_ldisc *tty_ldisc_ref(struct tty_struct *);
extern void tty_ldisc_deref(struct tty_ldisc *);
n->tc_verd = SET_TC_VERD(n->tc_verd, 0);
n->tc_verd = CLR_TC_OK2MUNGE(n->tc_verd);
n->tc_verd = CLR_TC_MUNGED(n->tc_verd);
- n->iif = skb->iif;
}
return n;
}
SCTP_SHUTDOWN_EVENT,
SCTP_PARTIAL_DELIVERY_EVENT,
SCTP_ADAPTATION_INDICATION,
- SCTP_AUTHENTICATION_EVENT,
+ SCTP_AUTHENTICATION_INDICATION,
};
/* Notification error codes used to fill up the error fields in some
return err;
rcu_read_lock_bh();
- filter = sk->sk_filter;
+ filter = rcu_dereference(sk->sk_filter);
if (filter) {
unsigned int pkt_len = sk_run_filter(skb, filter->insns,
filter->len);
return ret;
}
+static inline int xfrm_alg_len(struct xfrm_algo *alg)
+{
+ return sizeof(*alg) + ((alg->alg_key_len + 7) / 8);
+}
+
#ifdef CONFIG_XFRM_MIGRATE
static inline struct xfrm_algo *xfrm_algo_clone(struct xfrm_algo *orig)
{
- return (struct xfrm_algo *)kmemdup(orig, sizeof(*orig) + orig->alg_key_len, GFP_KERNEL);
+ return kmemdup(orig, xfrm_alg_len(orig), GFP_KERNEL);
}
static inline void xfrm_states_put(struct xfrm_state **states, int n)
endmenu # General setup
+config SLABINFO
+ bool
+ depends on PROC_FS
+ depends on SLAB || SLUB
+ default y
+
config RT_MUTEXES
boolean
select PLIST
#endif
#if ACCT_VERSION==3
ac.ac_pid = current->tgid;
- ac.ac_ppid = current->parent->tgid;
+ ac.ac_ppid = current->real_parent->tgid;
#endif
spin_lock_irq(¤t->sighand->siglock);
}
/*
- * Fixup the pi_state owner with current.
+ * Fixup the pi_state owner with the new owner.
*
* Must be called with hash bucket lock held and mm->sem held for non
* private futexes.
*/
static int fixup_pi_state_owner(u32 __user *uaddr, struct futex_q *q,
- struct task_struct *curr)
+ struct task_struct *newowner)
{
- u32 newtid = task_pid_vnr(curr) | FUTEX_WAITERS;
+ u32 newtid = task_pid_vnr(newowner) | FUTEX_WAITERS;
struct futex_pi_state *pi_state = q->pi_state;
u32 uval, curval, newval;
int ret;
} else
newtid |= FUTEX_OWNER_DIED;
- pi_state->owner = curr;
+ pi_state->owner = newowner;
- spin_lock_irq(&curr->pi_lock);
+ spin_lock_irq(&newowner->pi_lock);
WARN_ON(!list_empty(&pi_state->list));
- list_add(&pi_state->list, &curr->pi_state_list);
- spin_unlock_irq(&curr->pi_lock);
+ list_add(&pi_state->list, &newowner->pi_state_list);
+ spin_unlock_irq(&newowner->pi_lock);
/*
* We own it, so we have to replace the pending owner
* when we were on the way back before we locked the
* hash bucket.
*/
- if (q.pi_state->owner == curr &&
- rt_mutex_trylock(&q.pi_state->pi_mutex)) {
- ret = 0;
+ if (q.pi_state->owner == curr) {
+ /*
+ * Try to get the rt_mutex now. This might
+ * fail as some other task acquired the
+ * rt_mutex after we removed ourself from the
+ * rt_mutex waiters list.
+ */
+ if (rt_mutex_trylock(&q.pi_state->pi_mutex))
+ ret = 0;
+ else {
+ /*
+ * pi_state is incorrect, some other
+ * task did a lock steal and we
+ * returned due to timeout or signal
+ * without taking the rt_mutex. Too
+ * late. We can access the
+ * rt_mutex_owner without locking, as
+ * the other task is now blocked on
+ * the hash bucket lock. Fix the state
+ * up.
+ */
+ struct task_struct *owner;
+ int res;
+
+ owner = rt_mutex_owner(&q.pi_state->pi_mutex);
+ res = fixup_pi_state_owner(uaddr, &q, owner);
+
+ WARN_ON(rt_mutex_owner(&q.pi_state->pi_mutex) !=
+ owner);
+
+ /* propagate -EFAULT, if the fixup failed */
+ if (res)
+ ret = res;
+ }
} else {
/*
* Paranoia check. If we did not take the lock
VMCOREINFO_OFFSET(list_head, next);
VMCOREINFO_OFFSET(list_head, prev);
VMCOREINFO_LENGTH(zone.free_area, MAX_ORDER);
+ VMCOREINFO_LENGTH(free_area.free_list, MIGRATE_TYPES);
VMCOREINFO_NUMBER(NR_FREE_PAGES);
arch_crash_save_vmcoreinfo();
DEFINE_MUTEX(pm_mutex);
+unsigned int pm_flags;
+EXPORT_SYMBOL(pm_flags);
+
#ifdef CONFIG_SUSPEND
/* This is just an arbitrary number */
#include <linux/interrupt.h>
#include <linux/mutex.h>
-int pm_active;
-
/*
* Locking notes:
* pm_devs_lock can be a semaphore providing pm ops are not called
EXPORT_SYMBOL(pm_register);
EXPORT_SYMBOL(pm_send_all);
-EXPORT_SYMBOL(pm_active);
-
* commonly to provide a default console (ie from PROM variables) when
* the user has not supplied one.
*/
-int __init add_preferred_console(char *name, int idx, char *options)
+int add_preferred_console(char *name, int idx, char *options)
{
struct console_cmdline *c;
int i;
return ret;
}
-static int may_attach(struct task_struct *task)
+int __ptrace_may_attach(struct task_struct *task)
{
/* May we inspect the given task?
* This check is used both for attaching with ptrace
{
int err;
task_lock(task);
- err = may_attach(task);
+ err = __ptrace_may_attach(task);
task_unlock(task);
return !err;
}
/* the same process cannot be attached many times */
if (task->ptrace & PT_PTRACED)
goto bad;
- retval = may_attach(task);
+ retval = __ptrace_may_attach(task);
if (retval)
goto bad;
}
#endif
printk(KERN_CONT "%5lu %5d %6d\n", free,
- task_pid_nr(p), task_pid_nr(p->parent));
+ task_pid_nr(p), task_pid_nr(p->real_parent));
if (state != TASK_RUNNING)
show_stack(p, NULL);
/*
* Ease the printing of nsec fields:
*/
-static long long nsec_high(long long nsec)
+static long long nsec_high(unsigned long long nsec)
{
- if (nsec < 0) {
+ if ((long long)nsec < 0) {
nsec = -nsec;
do_div(nsec, 1000000);
return -nsec;
return nsec;
}
-static unsigned long nsec_low(long long nsec)
+static unsigned long nsec_low(unsigned long long nsec)
{
- if (nsec < 0)
+ if ((long long)nsec < 0)
nsec = -nsec;
return do_div(nsec, 1000000);
static struct page *xip_sparse_page(void)
{
if (!__xip_sparse_page) {
- unsigned long zeroes = get_zeroed_page(GFP_HIGHUSER);
- if (zeroes) {
+ struct page *page = alloc_page(GFP_HIGHUSER | __GFP_ZERO);
+
+ if (page) {
static DEFINE_SPINLOCK(xip_alloc_lock);
spin_lock(&xip_alloc_lock);
if (!__xip_sparse_page)
- __xip_sparse_page = virt_to_page(zeroes);
+ __xip_sparse_page = page;
else
- free_page(zeroes);
+ __free_page(page);
spin_unlock(&xip_alloc_lock);
}
}
mem_map = NODE_DATA(0)->node_mem_map;
#ifdef CONFIG_ARCH_POPULATES_NODE_MAP
if (page_to_pfn(mem_map) != pgdat->node_start_pfn)
- mem_map -= pgdat->node_start_pfn;
+ mem_map -= (pgdat->node_start_pfn - ARCH_PFN_OFFSET);
#endif /* CONFIG_ARCH_POPULATES_NODE_MAP */
}
#endif
schedule_delayed_work(work, round_jiffies_relative(REAPTIMEOUT_CPUC));
}
-#ifdef CONFIG_PROC_FS
+#ifdef CONFIG_SLABINFO
static void print_slabinfo_header(struct seq_file *m)
{
return slab_alloc(s, gfpflags, node, caller);
}
+static unsigned long count_partial(struct kmem_cache_node *n)
+{
+ unsigned long flags;
+ unsigned long x = 0;
+ struct page *page;
+
+ spin_lock_irqsave(&n->list_lock, flags);
+ list_for_each_entry(page, &n->partial, lru)
+ x += page->inuse;
+ spin_unlock_irqrestore(&n->list_lock, flags);
+ return x;
+}
+
#if defined(CONFIG_SYSFS) && defined(CONFIG_SLUB_DEBUG)
static int validate_slab(struct kmem_cache *s, struct page *page,
unsigned long *map)
return n;
}
-static unsigned long count_partial(struct kmem_cache_node *n)
-{
- unsigned long flags;
- unsigned long x = 0;
- struct page *page;
-
- spin_lock_irqsave(&n->list_lock, flags);
- list_for_each_entry(page, &n->partial, lru)
- x += page->inuse;
- spin_unlock_irqrestore(&n->list_lock, flags);
- return x;
-}
-
enum slab_stat_type {
SL_FULL,
SL_PARTIAL,
__initcall(slab_sysfs_init);
#endif
+
+/*
+ * The /proc/slabinfo ABI
+ */
+#ifdef CONFIG_SLABINFO
+
+ssize_t slabinfo_write(struct file *file, const char __user * buffer,
+ size_t count, loff_t *ppos)
+{
+ return -EINVAL;
+}
+
+
+static void print_slabinfo_header(struct seq_file *m)
+{
+ seq_puts(m, "slabinfo - version: 2.1\n");
+ seq_puts(m, "# name <active_objs> <num_objs> <objsize> "
+ "<objperslab> <pagesperslab>");
+ seq_puts(m, " : tunables <limit> <batchcount> <sharedfactor>");
+ seq_puts(m, " : slabdata <active_slabs> <num_slabs> <sharedavail>");
+ seq_putc(m, '\n');
+}
+
+static void *s_start(struct seq_file *m, loff_t *pos)
+{
+ loff_t n = *pos;
+
+ down_read(&slub_lock);
+ if (!n)
+ print_slabinfo_header(m);
+
+ return seq_list_start(&slab_caches, *pos);
+}
+
+static void *s_next(struct seq_file *m, void *p, loff_t *pos)
+{
+ return seq_list_next(p, &slab_caches, pos);
+}
+
+static void s_stop(struct seq_file *m, void *p)
+{
+ up_read(&slub_lock);
+}
+
+static int s_show(struct seq_file *m, void *p)
+{
+ unsigned long nr_partials = 0;
+ unsigned long nr_slabs = 0;
+ unsigned long nr_inuse = 0;
+ unsigned long nr_objs;
+ struct kmem_cache *s;
+ int node;
+
+ s = list_entry(p, struct kmem_cache, list);
+
+ for_each_online_node(node) {
+ struct kmem_cache_node *n = get_node(s, node);
+
+ if (!n)
+ continue;
+
+ nr_partials += n->nr_partial;
+ nr_slabs += atomic_long_read(&n->nr_slabs);
+ nr_inuse += count_partial(n);
+ }
+
+ nr_objs = nr_slabs * s->objects;
+ nr_inuse += (nr_slabs - nr_partials) * s->objects;
+
+ seq_printf(m, "%-17s %6lu %6lu %6u %4u %4d", s->name, nr_inuse,
+ nr_objs, s->size, s->objects, (1 << s->order));
+ seq_printf(m, " : tunables %4u %4u %4u", 0, 0, 0);
+ seq_printf(m, " : slabdata %6lu %6lu %6lu", nr_slabs, nr_slabs,
+ 0UL);
+ seq_putc(m, '\n');
+ return 0;
+}
+
+const struct seq_operations slabinfo_op = {
+ .start = s_start,
+ .next = s_next,
+ .stop = s_stop,
+ .show = s_show,
+};
+
+#endif /* CONFIG_SLABINFO */
if (eth->h_proto != htons(ETH_P_IP))
goto non_ip; /* Multi-Protocol Over ATM :-) */
+ /* Weed out funny packets (e.g., AF_PACKET or raw). */
+ if (skb->len < ETH_HLEN + sizeof(struct iphdr))
+ goto non_ip;
+ skb_set_network_header(skb, ETH_HLEN);
+ if (skb->len < ETH_HLEN + ip_hdr(skb)->ihl * 4 || ip_hdr(skb)->ihl < 5)
+ goto non_ip;
+
while (i < mpc->number_of_mps_macs) {
if (!compare_ether_addr(eth->h_dest, (mpc->mps_macs + i*ETH_ALEN)))
if ( send_via_shortcut(skb, mpc) == 0 ) /* try shortcut */
}
tasklet_disable(&hdev->tx_task);
-
- hci_conn_del_sysfs(conn);
-
hci_conn_hash_del(hdev, conn);
if (hdev->notify)
hdev->notify(hdev, HCI_NOTIFY_CONN_DEL);
-
tasklet_enable(&hdev->tx_task);
-
skb_queue_purge(&conn->data_q);
-
+ hci_conn_del_sysfs(conn);
hci_dev_put(hdev);
- /* will free via device release */
- put_device(&conn->dev);
-
return 0;
}
{
struct hci_conn *conn = container_of(work, struct hci_conn, work);
device_del(&conn->dev);
+ put_device(&conn->dev);
}
void hci_conn_del_sysfs(struct hci_conn *conn)
* still "owns" the NAPI instance and therefore can
* move the instance around on the list at-will.
*/
- if (unlikely(work == weight))
- list_move_tail(&n->poll_list, list);
+ if (unlikely(work == weight)) {
+ if (unlikely(napi_disable_pending(n)))
+ __napi_complete(n);
+ else
+ list_move_tail(&n->poll_list, list);
+ }
netpoll_poll_unlock(have);
}
C(len);
C(data_len);
C(mac_len);
- n->cloned = 1;
n->hdr_len = skb->nohdr ? skb_headroom(skb) : skb->hdr_len;
+ n->cloned = 1;
n->nohdr = 0;
n->destructor = NULL;
- C(truesize);
- atomic_set(&n->users, 1);
- C(head);
- C(data);
+ C(iif);
C(tail);
C(end);
+ C(head);
+ C(data);
+ C(truesize);
+ atomic_set(&n->users, 1);
atomic_inc(&(skb_shinfo(skb)->dataref));
skb->cloned = 1;
memcpy(ifa->ifa_label, dev->name, IFNAMSIZ);
if (named++ == 0)
continue;
- dot = strchr(ifa->ifa_label, ':');
+ dot = strchr(old, ':');
if (dot == NULL) {
sprintf(old, ":%d", named);
dot = old;
skb_shinfo(lro_desc->parent)->gso_size = lro_desc->mss;
if (lro_desc->vgrp) {
- if (test_bit(LRO_F_NAPI, &lro_mgr->features))
+ if (lro_mgr->features & LRO_F_NAPI)
vlan_hwaccel_receive_skb(lro_desc->parent,
lro_desc->vgrp,
lro_desc->vlan_tag);
lro_desc->vlan_tag);
} else {
- if (test_bit(LRO_F_NAPI, &lro_mgr->features))
+ if (lro_mgr->features & LRO_F_NAPI)
netif_receive_skb(lro_desc->parent);
else
netif_rx(lro_desc->parent);
goto out;
if ((skb->protocol == htons(ETH_P_8021Q))
- && !test_bit(LRO_F_EXTRACT_VLAN_ID, &lro_mgr->features))
+ && !(lro_mgr->features & LRO_F_EXTRACT_VLAN_ID))
vlan_hdr_len = VLAN_HLEN;
if (!lro_desc->active) { /* start new lro session */
goto out;
if ((skb->protocol == htons(ETH_P_8021Q))
- && !test_bit(LRO_F_EXTRACT_VLAN_ID, &lro_mgr->features))
+ && !(lro_mgr->features & LRO_F_EXTRACT_VLAN_ID))
vlan_hdr_len = VLAN_HLEN;
iph = (void *)(skb->data + vlan_hdr_len);
void *priv)
{
if (__lro_proc_skb(lro_mgr, skb, NULL, 0, priv)) {
- if (test_bit(LRO_F_NAPI, &lro_mgr->features))
+ if (lro_mgr->features & LRO_F_NAPI)
netif_receive_skb(skb);
else
netif_rx(skb);
void *priv)
{
if (__lro_proc_skb(lro_mgr, skb, vgrp, vlan_tag, priv)) {
- if (test_bit(LRO_F_NAPI, &lro_mgr->features))
+ if (lro_mgr->features & LRO_F_NAPI)
vlan_hwaccel_receive_skb(skb, vgrp, vlan_tag);
else
vlan_hwaccel_rx(skb, vgrp, vlan_tag);
if (!skb)
return;
- if (test_bit(LRO_F_NAPI, &lro_mgr->features))
+ if (lro_mgr->features & LRO_F_NAPI)
netif_receive_skb(skb);
else
netif_rx(skb);
if (!skb)
return;
- if (test_bit(LRO_F_NAPI, &lro_mgr->features))
+ if (lro_mgr->features & LRO_F_NAPI)
vlan_hwaccel_receive_skb(skb, vgrp, vlan_tag);
else
vlan_hwaccel_rx(skb, vgrp, vlan_tag);
return 1;
}
if (!strcmp(name, "off") || !strcmp(name, "none")) {
- ic_enable = 0;
- return 1;
+ return 0;
}
#ifdef CONFIG_IP_PNP_DHCP
else if (!strcmp(name, "dhcp")) {
int num = 0;
ic_set_manually = 1;
+ ic_enable = 1;
+ /*
+ * If any dhcp, bootp etc options are set, leave autoconfig on
+ * and skip the below static IP processing.
+ */
if (ic_proto_name(addrs))
return 1;
- /* Parse the whole string */
+ /* If no static IP is given, turn off autoconfig and bail. */
+ if (*addrs == 0 ||
+ strcmp(addrs, "off") == 0 ||
+ strcmp(addrs, "none") == 0) {
+ ic_enable = 0;
+ return 1;
+ }
+
+ /* Parse string for static IP assignment. */
ip = addrs;
while (ip && *ip) {
if ((cp = strchr(ip, ':')))
strlcpy(user_dev_name, ip, sizeof(user_dev_name));
break;
case 6:
- ic_proto_name(ip);
+ if (ic_proto_name(ip) == 0 &&
+ ic_myaddr == NONE) {
+ ic_enable = 0;
+ }
break;
}
}
int hh_len;
struct iphdr *iph;
struct sk_buff *skb;
+ unsigned int iphlen;
int err;
if (length > rt->u.dst.dev->mtu) {
goto error_fault;
/* We don't modify invalid header */
- if (length >= sizeof(*iph) && iph->ihl * 4U <= length) {
+ iphlen = iph->ihl * 4;
+ if (iphlen >= sizeof(*iph) && iphlen <= length) {
if (!iph->saddr)
iph->saddr = rt->rt_src;
iph->check = 0;
int idx, s_idx;
s_h = cb->args[0];
+ if (s_h < 0)
+ s_h = 0;
s_idx = idx = cb->args[1];
- for (h = 0; h <= rt_hash_mask; h++) {
- if (h < s_h) continue;
- if (h > s_h)
- s_idx = 0;
+ for (h = s_h; h <= rt_hash_mask; h++) {
rcu_read_lock_bh();
for (rt = rcu_dereference(rt_hash_table[h].chain), idx = 0; rt;
rt = rcu_dereference(rt->u.dst.rt_next), idx++) {
dst_release(xchg(&skb->dst, NULL));
}
rcu_read_unlock_bh();
+ s_idx = 0;
}
done:
u32 cnt = 0;
u32 reord = tp->packets_out;
s32 seq_rtt = -1;
+ s32 ca_seq_rtt = -1;
ktime_t last_ackt = net_invalid_timestamp();
while ((skb = tcp_write_queue_head(sk)) && skb != tcp_send_head(sk)) {
u32 packets_acked;
u8 sacked = scb->sacked;
+ /* Determine how many packets and what bytes were acked, tso and else */
if (after(scb->end_seq, tp->snd_una)) {
if (tcp_skb_pcount(skb) == 1 ||
!after(tp->snd_una, scb->seq))
if (sacked & TCPCB_SACKED_RETRANS)
tp->retrans_out -= packets_acked;
flag |= FLAG_RETRANS_DATA_ACKED;
+ ca_seq_rtt = -1;
seq_rtt = -1;
if ((flag & FLAG_DATA_ACKED) ||
(packets_acked > 1))
flag |= FLAG_NONHEAD_RETRANS_ACKED;
} else {
+ ca_seq_rtt = now - scb->when;
+ last_ackt = skb->tstamp;
if (seq_rtt < 0) {
- seq_rtt = now - scb->when;
- if (fully_acked)
- last_ackt = skb->tstamp;
+ seq_rtt = ca_seq_rtt;
}
if (!(sacked & TCPCB_SACKED_ACKED))
reord = min(cnt, reord);
!before(end_seq, tp->snd_up))
tp->urg_mode = 0;
} else {
+ ca_seq_rtt = now - scb->when;
+ last_ackt = skb->tstamp;
if (seq_rtt < 0) {
- seq_rtt = now - scb->when;
- if (fully_acked)
- last_ackt = skb->tstamp;
+ seq_rtt = ca_seq_rtt;
}
reord = min(cnt, reord);
}
net_invalid_timestamp()))
rtt_us = ktime_us_delta(ktime_get_real(),
last_ackt);
- else if (seq_rtt > 0)
- rtt_us = jiffies_to_usecs(seq_rtt);
+ else if (ca_seq_rtt > 0)
+ rtt_us = jiffies_to_usecs(ca_seq_rtt);
}
ca_ops->pkts_acked(sk, pkts_acked, rtt_us);
goto out;
}
sk->sk_bound_dev_if = usin->sin6_scope_id;
- if (!sk->sk_bound_dev_if &&
- (addr_type & IPV6_ADDR_MULTICAST))
- fl.oif = np->mcast_oif;
}
+ if (!sk->sk_bound_dev_if && (addr_type & IPV6_ADDR_MULTICAST))
+ sk->sk_bound_dev_if = np->mcast_oif;
+
/* Connect to link-local address requires an interface */
if (!sk->sk_bound_dev_if) {
err = -EINVAL;
self->max_sdu_size_rx = TTP_SAR_UNBOUND;
break;
default:
- IRDA_ERROR("%s: protocol not supported!\n",
- __FUNCTION__);
return -ESOCKTNOSUPPORT;
}
break;
sdata->bss->force_unicast_rateidx = -1;
if (rate->value < 0)
return 0;
- for (i=0; i< mode->num_rates; i++) {
+ for (i=0; i < mode->num_rates; i++) {
struct ieee80211_rate *rates = &mode->rates[i];
int this_rate = rates->rate;
sdata->bss->max_ratectrl_rateidx = i;
if (rate->fixed)
sdata->bss->force_unicast_rateidx = i;
- break;
+ return 0;
}
}
- return 0;
+ return -EINVAL;
}
static int ieee80211_ioctl_giwrate(struct net_device *dev,
chunksize = sizeof(init) + addrs_len + SCTP_SAT_LEN(num_types);
chunksize += sizeof(ecap_param);
+ if (sctp_prsctp_enable)
+ chunksize += sizeof(prsctp_param);
+
/* ADDIP: Section 4.2.7:
* An implementation supporting this extension [ADDIP] MUST list
* the ASCONF,the ASCONF-ACK, and the AUTH chunks in its INIT and
if (asoc->peer.ecn_capable)
chunksize += sizeof(ecap_param);
+ if (sctp_prsctp_enable)
+ chunksize += sizeof(prsctp_param);
+
if (sctp_addip_enable) {
extensions[num_ext] = SCTP_CID_ASCONF;
extensions[num_ext+1] = SCTP_CID_ASCONF_ACK;
new_asoc->c.initial_tsn = asoc->c.initial_tsn;
}
-static void sctp_auth_params_populate(struct sctp_association *new_asoc,
- const struct sctp_association *asoc)
-{
- /* Only perform this if AUTH extension is enabled */
- if (!sctp_auth_enable)
- return;
-
- /* We need to provide the same parameter information as
- * was in the original INIT. This means that we need to copy
- * the HMACS, CHUNKS, and RANDOM parameter from the original
- * assocaition.
- */
- memcpy(new_asoc->c.auth_random, asoc->c.auth_random,
- sizeof(asoc->c.auth_random));
- memcpy(new_asoc->c.auth_hmacs, asoc->c.auth_hmacs,
- sizeof(asoc->c.auth_hmacs));
- memcpy(new_asoc->c.auth_chunks, asoc->c.auth_chunks,
- sizeof(asoc->c.auth_chunks));
-}
-
/*
* Compare vtag/tietag values to determine unexpected COOKIE-ECHO
* handling action.
sctp_tietags_populate(new_asoc, asoc);
- sctp_auth_params_populate(new_asoc, asoc);
-
/* B) "Z" shall respond immediately with an INIT ACK chunk. */
/* If there are errors need to be reported for unknown parameters,
ak = (struct sctp_authkey_event *)
skb_put(skb, sizeof(struct sctp_authkey_event));
- ak->auth_type = SCTP_AUTHENTICATION_EVENT;
+ ak->auth_type = SCTP_AUTHENTICATION_INDICATION;
ak->auth_flags = 0;
ak->auth_length = sizeof(struct sctp_authkey_event);
err = -EINVAL;
gss_auth->mech = gss_mech_get_by_pseudoflavor(flavor);
if (!gss_auth->mech) {
- printk(KERN_WARNING "%s: Pseudoflavor %d not found!",
+ printk(KERN_WARNING "%s: Pseudoflavor %d not found!\n",
__FUNCTION__, flavor);
goto err_free;
}
goto out;
if ( (skbn = pskb_copy(skb, GFP_ATOMIC)) == NULL){
- goto out;
+ goto output;
}
x25_transmit_link(skbn, nb);
- x25_neigh_put(nb);
rc = 1;
+output:
+ x25_neigh_put(nb);
out:
return rc;
}
}
EXPORT_SYMBOL(km_policy_expired);
+#ifdef CONFIG_XFRM_MIGRATE
int km_migrate(struct xfrm_selector *sel, u8 dir, u8 type,
struct xfrm_migrate *m, int num_migrate)
{
return err;
}
EXPORT_SYMBOL(km_migrate);
+#endif
int km_report(u8 proto, struct xfrm_selector *sel, xfrm_address_t *addr)
{
#include <linux/in6.h>
#endif
-static inline int alg_len(struct xfrm_algo *alg)
-{
- return sizeof(*alg) + ((alg->alg_key_len + 7) / 8);
-}
-
static int verify_one_alg(struct nlattr **attrs, enum xfrm_attr_type_t type)
{
struct nlattr *rt = attrs[type];
return 0;
algp = nla_data(rt);
- if (nla_len(rt) < alg_len(algp))
+ if (nla_len(rt) < xfrm_alg_len(algp))
return -EINVAL;
switch (type) {
return -ENOSYS;
*props = algo->desc.sadb_alg_id;
- p = kmemdup(ualg, alg_len(ualg), GFP_KERNEL);
+ p = kmemdup(ualg, xfrm_alg_len(ualg), GFP_KERNEL);
if (!p)
return -ENOMEM;
NLA_PUT_U64(skb, XFRMA_LASTUSED, x->lastused);
if (x->aalg)
- NLA_PUT(skb, XFRMA_ALG_AUTH, alg_len(x->aalg), x->aalg);
+ NLA_PUT(skb, XFRMA_ALG_AUTH, xfrm_alg_len(x->aalg), x->aalg);
if (x->ealg)
- NLA_PUT(skb, XFRMA_ALG_CRYPT, alg_len(x->ealg), x->ealg);
+ NLA_PUT(skb, XFRMA_ALG_CRYPT, xfrm_alg_len(x->ealg), x->ealg);
if (x->calg)
NLA_PUT(skb, XFRMA_ALG_COMP, sizeof(*(x->calg)), x->calg);
{
size_t l = 0;
if (x->aalg)
- l += nla_total_size(alg_len(x->aalg));
+ l += nla_total_size(xfrm_alg_len(x->aalg));
if (x->ealg)
- l += nla_total_size(alg_len(x->ealg));
+ l += nla_total_size(xfrm_alg_len(x->ealg));
if (x->calg)
l += nla_total_size(sizeof(*x->calg));
if (x->encap)
rslot->number = idx;
}
+/* In a separate function to keep gcc 3.2 happy - do NOT merge this in
+ snd_mixer_oss_build_input! */
+static int snd_mixer_oss_build_test_all(struct snd_mixer_oss *mixer,
+ struct snd_mixer_oss_assign_table *ptr,
+ struct slot *slot)
+{
+ char str[64];
+ int err;
+
+ err = snd_mixer_oss_build_test(mixer, slot, ptr->name, ptr->index,
+ SNDRV_MIXER_OSS_ITEM_GLOBAL);
+ if (err)
+ return err;
+ sprintf(str, "%s Switch", ptr->name);
+ err = snd_mixer_oss_build_test(mixer, slot, str, ptr->index,
+ SNDRV_MIXER_OSS_ITEM_GSWITCH);
+ if (err)
+ return err;
+ sprintf(str, "%s Route", ptr->name);
+ err = snd_mixer_oss_build_test(mixer, slot, str, ptr->index,
+ SNDRV_MIXER_OSS_ITEM_GROUTE);
+ if (err)
+ return err;
+ sprintf(str, "%s Volume", ptr->name);
+ err = snd_mixer_oss_build_test(mixer, slot, str, ptr->index,
+ SNDRV_MIXER_OSS_ITEM_GVOLUME);
+ if (err)
+ return err;
+ sprintf(str, "%s Playback Switch", ptr->name);
+ err = snd_mixer_oss_build_test(mixer, slot, str, ptr->index,
+ SNDRV_MIXER_OSS_ITEM_PSWITCH);
+ if (err)
+ return err;
+ sprintf(str, "%s Playback Route", ptr->name);
+ err = snd_mixer_oss_build_test(mixer, slot, str, ptr->index,
+ SNDRV_MIXER_OSS_ITEM_PROUTE);
+ if (err)
+ return err;
+ sprintf(str, "%s Playback Volume", ptr->name);
+ err = snd_mixer_oss_build_test(mixer, slot, str, ptr->index,
+ SNDRV_MIXER_OSS_ITEM_PVOLUME);
+ if (err)
+ return err;
+ sprintf(str, "%s Capture Switch", ptr->name);
+ err = snd_mixer_oss_build_test(mixer, slot, str, ptr->index,
+ SNDRV_MIXER_OSS_ITEM_CSWITCH);
+ if (err)
+ return err;
+ sprintf(str, "%s Capture Route", ptr->name);
+ err = snd_mixer_oss_build_test(mixer, slot, str, ptr->index,
+ SNDRV_MIXER_OSS_ITEM_CROUTE);
+ if (err)
+ return err;
+ sprintf(str, "%s Capture Volume", ptr->name);
+ err = snd_mixer_oss_build_test(mixer, slot, str, ptr->index,
+ SNDRV_MIXER_OSS_ITEM_CVOLUME);
+ if (err)
+ return err;
+
+ return 0;
+}
+
/*
* build an OSS mixer element.
* ptr_allocated means the entry is dynamically allocated (change via proc file).
memset(&slot, 0, sizeof(slot));
memset(slot.numid, 0xff, sizeof(slot.numid)); /* ID_UNKNOWN */
- if (snd_mixer_oss_build_test(mixer, &slot, ptr->name, ptr->index,
- SNDRV_MIXER_OSS_ITEM_GLOBAL))
- return 0;
- sprintf(str, "%s Switch", ptr->name);
- if (snd_mixer_oss_build_test(mixer, &slot, str, ptr->index,
- SNDRV_MIXER_OSS_ITEM_GSWITCH))
- return 0;
- sprintf(str, "%s Route", ptr->name);
- if (snd_mixer_oss_build_test(mixer, &slot, str, ptr->index,
- SNDRV_MIXER_OSS_ITEM_GROUTE))
- return 0;
- sprintf(str, "%s Volume", ptr->name);
- if (snd_mixer_oss_build_test(mixer, &slot, str, ptr->index,
- SNDRV_MIXER_OSS_ITEM_GVOLUME))
- return 0;
- sprintf(str, "%s Playback Switch", ptr->name);
- if (snd_mixer_oss_build_test(mixer, &slot, str, ptr->index,
- SNDRV_MIXER_OSS_ITEM_PSWITCH))
- return 0;
- sprintf(str, "%s Playback Route", ptr->name);
- if (snd_mixer_oss_build_test(mixer, &slot, str, ptr->index,
- SNDRV_MIXER_OSS_ITEM_PROUTE))
- return 0;
- sprintf(str, "%s Playback Volume", ptr->name);
- if (snd_mixer_oss_build_test(mixer, &slot, str, ptr->index,
- SNDRV_MIXER_OSS_ITEM_PVOLUME))
- return 0;
- sprintf(str, "%s Capture Switch", ptr->name);
- if (snd_mixer_oss_build_test(mixer, &slot, str, ptr->index,
- SNDRV_MIXER_OSS_ITEM_CSWITCH))
- return 0;
- sprintf(str, "%s Capture Route", ptr->name);
- if (snd_mixer_oss_build_test(mixer, &slot, str, ptr->index,
- SNDRV_MIXER_OSS_ITEM_CROUTE))
- return 0;
- sprintf(str, "%s Capture Volume", ptr->name);
- if (snd_mixer_oss_build_test(mixer, &slot, str, ptr->index,
- SNDRV_MIXER_OSS_ITEM_CVOLUME))
+ if (snd_mixer_oss_build_test_all(mixer, ptr, &slot))
return 0;
down_read(&mixer->card->controls_rwsem);
if (ptr->index == 0 && (kctl = snd_mixer_oss_test_id(mixer, "Capture Source", 0)) != NULL) {
OSDN Git Service
