--- /dev/null
+===================================
+cfag12864b LCD Driver Documentation
+===================================
+
+:License: GPLv2
+:Author & Maintainer: Miguel Ojeda Sandonis
+:Date: 2006-10-27
+
+
+
+.. INDEX
+
+ 1. DRIVER INFORMATION
+ 2. DEVICE INFORMATION
+ 3. WIRING
+ 4. USERSPACE PROGRAMMING
+
+1. Driver Information
+---------------------
+
+This driver supports a cfag12864b LCD.
+
+
+2. Device Information
+---------------------
+
+:Manufacturer: Crystalfontz
+:Device Name: Crystalfontz 12864b LCD Series
+:Device Code: cfag12864b
+:Webpage: http://www.crystalfontz.com
+:Device Webpage: http://www.crystalfontz.com/products/12864b/
+:Type: LCD (Liquid Crystal Display)
+:Width: 128
+:Height: 64
+:Colors: 2 (B/N)
+:Controller: ks0108
+:Controllers: 2
+:Pages: 8 each controller
+:Addresses: 64 each page
+:Data size: 1 byte each address
+:Memory size: 2 * 8 * 64 * 1 = 1024 bytes = 1 Kbyte
+
+
+3. Wiring
+---------
+
+The cfag12864b LCD Series don't have official wiring.
+
+The common wiring is done to the parallel port as shown::
+
+ Parallel Port cfag12864b
+
+ Name Pin# Pin# Name
+
+ Strobe ( 1)------------------------------(17) Enable
+ Data 0 ( 2)------------------------------( 4) Data 0
+ Data 1 ( 3)------------------------------( 5) Data 1
+ Data 2 ( 4)------------------------------( 6) Data 2
+ Data 3 ( 5)------------------------------( 7) Data 3
+ Data 4 ( 6)------------------------------( 8) Data 4
+ Data 5 ( 7)------------------------------( 9) Data 5
+ Data 6 ( 8)------------------------------(10) Data 6
+ Data 7 ( 9)------------------------------(11) Data 7
+ (10) [+5v]---( 1) Vdd
+ (11) [GND]---( 2) Ground
+ (12) [+5v]---(14) Reset
+ (13) [GND]---(15) Read / Write
+ Line (14)------------------------------(13) Controller Select 1
+ (15)
+ Init (16)------------------------------(12) Controller Select 2
+ Select (17)------------------------------(16) Data / Instruction
+ Ground (18)---[GND] [+5v]---(19) LED +
+ Ground (19)---[GND]
+ Ground (20)---[GND] E A Values:
+ Ground (21)---[GND] [GND]---[P1]---(18) Vee - R = Resistor = 22 ohm
+ Ground (22)---[GND] | - P1 = Preset = 10 Kohm
+ Ground (23)---[GND] ---- S ------( 3) V0 - P2 = Preset = 1 Kohm
+ Ground (24)---[GND] | |
+ Ground (25)---[GND] [GND]---[P2]---[R]---(20) LED -
+
+
+4. Userspace Programming
+------------------------
+
+The cfag12864bfb describes a framebuffer device (/dev/fbX).
+
+It has a size of 1024 bytes = 1 Kbyte.
+Each bit represents one pixel. If the bit is high, the pixel will
+turn on. If the pixel is low, the pixel will turn off.
+
+You can use the framebuffer as a file: fopen, fwrite, fclose...
+Although the LCD won't get updated until the next refresh time arrives.
+
+Also, you can mmap the framebuffer: open & mmap, munmap & close...
+which is the best option for most uses.
+
+Check samples/auxdisplay/cfag12864b-example.c
+for a real working userspace complete program with usage examples.
--- /dev/null
+=========================
+Auxiliary Display Support
+=========================
+
+.. toctree::
+ :maxdepth: 1
+
+ ks0108.rst
+ cfag12864b.rst
+
+.. only:: subproject and html
+
+ Indices
+ =======
+
+ * :ref:`genindex`
--- /dev/null
+==========================================
+ks0108 LCD Controller Driver Documentation
+==========================================
+
+:License: GPLv2
+:Author & Maintainer: Miguel Ojeda Sandonis
+:Date: 2006-10-27
+
+
+
+.. INDEX
+
+ 1. DRIVER INFORMATION
+ 2. DEVICE INFORMATION
+ 3. WIRING
+
+
+1. Driver Information
+---------------------
+
+This driver supports the ks0108 LCD controller.
+
+
+2. Device Information
+---------------------
+
+:Manufacturer: Samsung
+:Device Name: KS0108 LCD Controller
+:Device Code: ks0108
+:Webpage: -
+:Device Webpage: -
+:Type: LCD Controller (Liquid Crystal Display Controller)
+:Width: 64
+:Height: 64
+:Colors: 2 (B/N)
+:Pages: 8
+:Addresses: 64 each page
+:Data size: 1 byte each address
+:Memory size: 8 * 64 * 1 = 512 bytes
+
+
+3. Wiring
+---------
+
+The driver supports data parallel port wiring.
+
+If you aren't building LCD related hardware, you should check
+your LCD specific wiring information in the same folder.
+
+For example, check Documentation/admin-guide/auxdisplay/cfag12864b.rst
iostats
kernel-per-CPU-kthreads
laptops/index
+ auxdisplay/index
lcd-panel-cgram
ldm
lockup-watchdogs
+++ /dev/null
- ===================================
- cfag12864b LCD Driver Documentation
- ===================================
-
-License: GPLv2
-Author & Maintainer: Miguel Ojeda Sandonis
-Date: 2006-10-27
-
-
-
---------
-0. INDEX
---------
-
- 1. DRIVER INFORMATION
- 2. DEVICE INFORMATION
- 3. WIRING
- 4. USERSPACE PROGRAMMING
-
-
----------------------
-1. DRIVER INFORMATION
----------------------
-
-This driver supports a cfag12864b LCD.
-
-
----------------------
-2. DEVICE INFORMATION
----------------------
-
-Manufacturer: Crystalfontz
-Device Name: Crystalfontz 12864b LCD Series
-Device Code: cfag12864b
-Webpage: http://www.crystalfontz.com
-Device Webpage: http://www.crystalfontz.com/products/12864b/
-Type: LCD (Liquid Crystal Display)
-Width: 128
-Height: 64
-Colors: 2 (B/N)
-Controller: ks0108
-Controllers: 2
-Pages: 8 each controller
-Addresses: 64 each page
-Data size: 1 byte each address
-Memory size: 2 * 8 * 64 * 1 = 1024 bytes = 1 Kbyte
-
-
----------
-3. WIRING
----------
-
-The cfag12864b LCD Series don't have official wiring.
-
-The common wiring is done to the parallel port as shown:
-
-Parallel Port cfag12864b
-
- Name Pin# Pin# Name
-
-Strobe ( 1)------------------------------(17) Enable
-Data 0 ( 2)------------------------------( 4) Data 0
-Data 1 ( 3)------------------------------( 5) Data 1
-Data 2 ( 4)------------------------------( 6) Data 2
-Data 3 ( 5)------------------------------( 7) Data 3
-Data 4 ( 6)------------------------------( 8) Data 4
-Data 5 ( 7)------------------------------( 9) Data 5
-Data 6 ( 8)------------------------------(10) Data 6
-Data 7 ( 9)------------------------------(11) Data 7
- (10) [+5v]---( 1) Vdd
- (11) [GND]---( 2) Ground
- (12) [+5v]---(14) Reset
- (13) [GND]---(15) Read / Write
- Line (14)------------------------------(13) Controller Select 1
- (15)
- Init (16)------------------------------(12) Controller Select 2
-Select (17)------------------------------(16) Data / Instruction
-Ground (18)---[GND] [+5v]---(19) LED +
-Ground (19)---[GND]
-Ground (20)---[GND] E A Values:
-Ground (21)---[GND] [GND]---[P1]---(18) Vee - R = Resistor = 22 ohm
-Ground (22)---[GND] | - P1 = Preset = 10 Kohm
-Ground (23)---[GND] ---- S ------( 3) V0 - P2 = Preset = 1 Kohm
-Ground (24)---[GND] | |
-Ground (25)---[GND] [GND]---[P2]---[R]---(20) LED -
-
-
-------------------------
-4. USERSPACE PROGRAMMING
-------------------------
-
-The cfag12864bfb describes a framebuffer device (/dev/fbX).
-
-It has a size of 1024 bytes = 1 Kbyte.
-Each bit represents one pixel. If the bit is high, the pixel will
-turn on. If the pixel is low, the pixel will turn off.
-
-You can use the framebuffer as a file: fopen, fwrite, fclose...
-Although the LCD won't get updated until the next refresh time arrives.
-
-Also, you can mmap the framebuffer: open & mmap, munmap & close...
-which is the best option for most uses.
-
-Check samples/auxdisplay/cfag12864b-example.c
-for a real working userspace complete program with usage examples.
+++ /dev/null
- ==========================================
- ks0108 LCD Controller Driver Documentation
- ==========================================
-
-License: GPLv2
-Author & Maintainer: Miguel Ojeda Sandonis
-Date: 2006-10-27
-
-
-
---------
-0. INDEX
---------
-
- 1. DRIVER INFORMATION
- 2. DEVICE INFORMATION
- 3. WIRING
-
-
----------------------
-1. DRIVER INFORMATION
----------------------
-
-This driver supports the ks0108 LCD controller.
-
-
----------------------
-2. DEVICE INFORMATION
----------------------
-
-Manufacturer: Samsung
-Device Name: KS0108 LCD Controller
-Device Code: ks0108
-Webpage: -
-Device Webpage: -
-Type: LCD Controller (Liquid Crystal Display Controller)
-Width: 64
-Height: 64
-Colors: 2 (B/N)
-Pages: 8
-Addresses: 64 each page
-Data size: 1 byte each address
-Memory size: 8 * 64 * 1 = 512 bytes
-
-
----------
-3. WIRING
----------
-
-The driver supports data parallel port wiring.
-
-If you aren't building LCD related hardware, you should check
-your LCD specific wiring information in the same folder.
-
-For example, check Documentation/auxdisplay/cfag12864b.
KS0108 LCD CONTROLLER DRIVER
M: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com>
S: Maintained
-F: Documentation/auxdisplay/ks0108
+F: Documentation/admin-guide/auxdisplay/ks0108.rst
F: drivers/auxdisplay/ks0108.c
F: include/linux/ks0108.h
say Y. You also need the ks0108 LCD Controller driver.
For help about how to wire your LCD to the parallel port,
- check Documentation/auxdisplay/cfag12864b
+ check Documentation/admin-guide/auxdisplay/cfag12864b.rst
Depends on the x86 arch and the framebuffer support.