#define DEFAULT_RSSI -128
/*
- * When no TX/RX percentage could be calculated due to lack of
- * frames on the air, we fallback to a percentage of 50%.
- * This will assure we will get at least get some decent value
- * when the link tuner starts.
- * The value will be dropped and overwritten with the correct (measured)
- * value anyway during the first run of the link tuner.
- */
-#define DEFAULT_PERCENTAGE 50
-
-/*
- * Small helper macro for percentage calculation
- * This is a very simple macro with the only catch that it will
- * produce a default value in case no total value was provided.
- */
-#define PERCENTAGE(__value, __total) \
- ( (__total) ? (((__value) * 100) / (__total)) : (DEFAULT_PERCENTAGE) )
-
-/*
* Helper struct and macro to work with moving/walking averages.
* When adding a value to the average value the following calculation
* is needed:
__new; \
})
-/*
- * For calculating the Signal quality we have determined
- * the total number of success and failed RX and TX frames.
- * With the addition of the average RSSI value we can determine
- * the link quality using the following algorithm:
- *
- * rssi_percentage = (avg_rssi * 100) / rssi_offset
- * rx_percentage = (rx_success * 100) / rx_total
- * tx_percentage = (tx_success * 100) / tx_total
- * avg_signal = ((WEIGHT_RSSI * avg_rssi) +
- * (WEIGHT_TX * tx_percentage) +
- * (WEIGHT_RX * rx_percentage)) / 100
- *
- * This value should then be checked to not be greater then 100.
- * This means the values of WEIGHT_RSSI, WEIGHT_RX, WEIGHT_TX must
- * sum up to 100 as well.
- */
-#define WEIGHT_RSSI 20
-#define WEIGHT_RX 40
-#define WEIGHT_TX 40
-
static int rt2x00link_antenna_get_link_rssi(struct rt2x00_dev *rt2x00dev)
{
struct link_ant *ant = &rt2x00dev->link.ant;
ant->rssi_ant = MOVING_AVERAGE(ant->rssi_ant, rxdesc->rssi);
}
-static void rt2x00link_precalculate_signal(struct rt2x00_dev *rt2x00dev)
-{
- struct link *link = &rt2x00dev->link;
- struct link_qual *qual = &rt2x00dev->link.qual;
-
- link->rx_percentage =
- PERCENTAGE(qual->rx_success, qual->rx_failed + qual->rx_success);
- link->tx_percentage =
- PERCENTAGE(qual->tx_success, qual->tx_failed + qual->tx_success);
-}
-
-int rt2x00link_calculate_signal(struct rt2x00_dev *rt2x00dev, int rssi)
-{
- struct link *link = &rt2x00dev->link;
- int rssi_percentage = 0;
- int signal;
-
- /*
- * We need a positive value for the RSSI.
- */
- if (rssi < 0)
- rssi += rt2x00dev->rssi_offset;
-
- /*
- * Calculate the different percentages,
- * which will be used for the signal.
- */
- rssi_percentage = PERCENTAGE(rssi, rt2x00dev->rssi_offset);
-
- /*
- * Add the individual percentages and use the WEIGHT
- * defines to calculate the current link signal.
- */
- signal = ((WEIGHT_RSSI * rssi_percentage) +
- (WEIGHT_TX * link->tx_percentage) +
- (WEIGHT_RX * link->rx_percentage)) / 100;
-
- return max_t(int, signal, 100);
-}
-
void rt2x00link_start_tuner(struct rt2x00_dev *rt2x00dev)
{
struct link *link = &rt2x00dev->link;
if (!rt2x00dev->intf_ap_count && !rt2x00dev->intf_sta_count)
return;
- link->rx_percentage = DEFAULT_PERCENTAGE;
- link->tx_percentage = DEFAULT_PERCENTAGE;
-
rt2x00link_reset_tuner(rt2x00dev, false);
if (test_bit(DEVICE_STATE_PRESENT, &rt2x00dev->flags))
rt2x00dev->ops->lib->link_tuner(rt2x00dev, qual, link->count);
/*
- * Precalculate a portion of the link signal which is
- * in based on the tx/rx success/failure counters.
- */
- rt2x00link_precalculate_signal(rt2x00dev);
-
- /*
* Send a signal to the led to update the led signal strength.
*/
rt2x00leds_led_quality(rt2x00dev, qual->rssi);