OSDN Git Service

ieee802154: add basic support for RF212 to at86rf230 driver
authorPhoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Mon, 17 Feb 2014 10:34:06 +0000 (11:34 +0100)
committerDavid S. Miller <davem@davemloft.net>
Mon, 17 Feb 2014 21:42:37 +0000 (16:42 -0500)
Since the AT86RF2xy chips are mostly compatible, this is only a small
change to the actual driver code. The at86rf230 driver already supports the
RF212 in most places, only three small adjustments are required:

 * force the initial state after P_ON to FORCE_TRX_OFF to work around a
   documented erratum
 * channels_supported depends on the frequency of the transceiver, and
   thus is_rf212
 * do early detection of chip version select an appropriate _ops struct
   based on the chip version.

Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ieee802154/at86rf230.c

index ab31544..6dd9782 100644 (file)
@@ -37,7 +37,6 @@
 
 struct at86rf230_local {
        struct spi_device *spi;
-       int rstn, slp_tr, dig2;
 
        u8 part;
        u8 vers;
@@ -55,6 +54,11 @@ struct at86rf230_local {
        bool is_tx;
 };
 
+static inline int is_rf212(struct at86rf230_local *local)
+{
+       return local->part == 7;
+}
+
 #define        RG_TRX_STATUS   (0x01)
 #define        SR_TRX_STATUS           0x01, 0x1f, 0
 #define        SR_RESERVED_01_3        0x01, 0x20, 5
@@ -100,7 +104,9 @@ struct at86rf230_local {
 #define        SR_SFD_VALUE            0x0b, 0xff, 0
 #define        RG_TRX_CTRL_2   (0x0c)
 #define        SR_OQPSK_DATA_RATE      0x0c, 0x03, 0
-#define        SR_RESERVED_0c_2        0x0c, 0x7c, 2
+#define        SR_SUB_MODE             0x0c, 0x04, 2
+#define        SR_BPSK_QPSK            0x0c, 0x08, 3
+#define        SR_RESERVED_0c_4        0x0c, 0x70, 4
 #define        SR_RX_SAFE_MODE         0x0c, 0x80, 7
 #define        RG_ANT_DIV      (0x0d)
 #define        SR_ANT_CTRL             0x0d, 0x03, 0
@@ -244,6 +250,57 @@ struct at86rf230_local {
 #define STATE_TRANSITION_IN_PROGRESS 0x1F
 
 static int
+__at86rf230_detect_device(struct spi_device *spi, u16 *man_id, u8 *part,
+               u8 *version)
+{
+       u8 data[4];
+       u8 *buf = kmalloc(2, GFP_KERNEL);
+       int status;
+       struct spi_message msg;
+       struct spi_transfer xfer = {
+               .len    = 2,
+               .tx_buf = buf,
+               .rx_buf = buf,
+       };
+       u8 reg;
+
+       if (!buf)
+               return -ENOMEM;
+
+       for (reg = RG_PART_NUM; reg <= RG_MAN_ID_1; reg++) {
+               buf[0] = (reg & CMD_REG_MASK) | CMD_REG;
+               buf[1] = 0xff;
+               dev_vdbg(&spi->dev, "buf[0] = %02x\n", buf[0]);
+               spi_message_init(&msg);
+               spi_message_add_tail(&xfer, &msg);
+
+               status = spi_sync(spi, &msg);
+               dev_vdbg(&spi->dev, "status = %d\n", status);
+               if (msg.status)
+                       status = msg.status;
+
+               dev_vdbg(&spi->dev, "status = %d\n", status);
+               dev_vdbg(&spi->dev, "buf[0] = %02x\n", buf[0]);
+               dev_vdbg(&spi->dev, "buf[1] = %02x\n", buf[1]);
+
+               if (status == 0)
+                       data[reg - RG_PART_NUM] = buf[1];
+               else
+                       break;
+       }
+
+       if (status == 0) {
+               *part = data[0];
+               *version = data[1];
+               *man_id = (data[3] << 8) | data[2];
+       }
+
+       kfree(buf);
+
+       return status;
+}
+
+static int
 __at86rf230_write(struct at86rf230_local *lp, u8 addr, u8 data)
 {
        u8 *buf = lp->buf;
@@ -520,6 +577,27 @@ at86rf230_stop(struct ieee802154_dev *dev)
 }
 
 static int
+at86rf230_set_channel(struct at86rf230_local *lp, int page, int channel)
+{
+       return at86rf230_write_subreg(lp, SR_CHANNEL, channel);
+}
+
+static int
+at86rf212_set_channel(struct at86rf230_local *lp, int page, int channel)
+{
+       int rc;
+
+       if (channel == 0)
+               rc = at86rf230_write_subreg(lp, SR_SUB_MODE, 0);
+       else
+               rc = at86rf230_write_subreg(lp, SR_SUB_MODE, 1);
+       if (rc < 0)
+               return rc;
+
+       return at86rf230_write_subreg(lp, SR_CHANNEL, channel);
+}
+
+static int
 at86rf230_channel(struct ieee802154_dev *dev, int page, int channel)
 {
        struct at86rf230_local *lp = dev->priv;
@@ -527,12 +605,19 @@ at86rf230_channel(struct ieee802154_dev *dev, int page, int channel)
 
        might_sleep();
 
-       if (page != 0 || channel < 11 || channel > 26) {
+       if (page < 0 || page > 31 ||
+           !(lp->dev->phy->channels_supported[page] & BIT(channel))) {
                WARN_ON(1);
                return -EINVAL;
        }
 
-       rc = at86rf230_write_subreg(lp, SR_CHANNEL, channel);
+       if (is_rf212(lp))
+               rc = at86rf212_set_channel(lp, page, channel);
+       else
+               rc = at86rf230_set_channel(lp, page, channel);
+       if (rc < 0)
+               return rc;
+
        msleep(1); /* Wait for PLL */
        dev->phy->current_channel = channel;
 
@@ -678,6 +763,16 @@ static struct ieee802154_ops at86rf230_ops = {
        .set_hw_addr_filt = at86rf230_set_hw_addr_filt,
 };
 
+static struct ieee802154_ops at86rf212_ops = {
+       .owner = THIS_MODULE,
+       .xmit = at86rf230_xmit,
+       .ed = at86rf230_ed,
+       .set_channel = at86rf230_channel,
+       .start = at86rf230_start,
+       .stop = at86rf230_stop,
+       .set_hw_addr_filt = at86rf230_set_hw_addr_filt,
+};
+
 static void at86rf230_irqwork(struct work_struct *work)
 {
        struct at86rf230_local *lp =
@@ -759,7 +854,8 @@ static int at86rf230_hw_init(struct at86rf230_local *lp)
 
        dev_info(&lp->spi->dev, "Status: %02x\n", status);
        if (status == STATE_P_ON) {
-               rc = at86rf230_write_subreg(lp, SR_TRX_CMD, STATE_TRX_OFF);
+               rc = at86rf230_write_subreg(lp, SR_TRX_CMD,
+                                           STATE_FORCE_TRX_OFF);
                if (rc)
                        return rc;
                msleep(1);
@@ -824,26 +920,18 @@ static int at86rf230_hw_init(struct at86rf230_local *lp)
        return 0;
 }
 
-static void at86rf230_fill_data(struct spi_device *spi)
-{
-       struct at86rf230_local *lp = spi_get_drvdata(spi);
-       struct at86rf230_platform_data *pdata = spi->dev.platform_data;
-
-       lp->rstn = pdata->rstn;
-       lp->slp_tr = pdata->slp_tr;
-       lp->dig2 = pdata->dig2;
-}
-
 static int at86rf230_probe(struct spi_device *spi)
 {
        struct at86rf230_platform_data *pdata;
        struct ieee802154_dev *dev;
        struct at86rf230_local *lp;
-       u8 man_id_0, man_id_1, status;
+       u16 man_id = 0;
+       u8 part = 0, version = 0, status;
        irq_handler_t irq_handler;
        work_func_t irq_worker;
-       int rc, supported = 0;
+       int rc;
        const char *chip;
+       struct ieee802154_ops *ops = NULL;
 
        if (!spi->irq) {
                dev_err(&spi->dev, "no IRQ specified\n");
@@ -856,116 +944,115 @@ static int at86rf230_probe(struct spi_device *spi)
                return -EINVAL;
        }
 
-       dev = ieee802154_alloc_device(sizeof(*lp), &at86rf230_ops);
-       if (!dev)
-               return -ENOMEM;
-
-       lp = dev->priv;
-       lp->dev = dev;
-
-       lp->spi = spi;
-
-       dev->parent = &spi->dev;
-       dev->extra_tx_headroom = 0;
-       /* We do support only 2.4 Ghz */
-       dev->phy->channels_supported[0] = 0x7FFF800;
-       dev->flags = IEEE802154_HW_OMIT_CKSUM;
-
-       if (pdata->irq_type & (IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING)) {
-               irq_worker = at86rf230_irqwork;
-               irq_handler = at86rf230_isr;
-       } else {
-               irq_worker = at86rf230_irqwork_level;
-               irq_handler = at86rf230_isr_level;
-       }
-
-       mutex_init(&lp->bmux);
-       INIT_WORK(&lp->irqwork, irq_worker);
-       spin_lock_init(&lp->lock);
-       init_completion(&lp->tx_complete);
-
-       spi_set_drvdata(spi, lp);
-
-       at86rf230_fill_data(spi);
-
-       rc = gpio_request(lp->rstn, "rstn");
+       rc = gpio_request(pdata->rstn, "rstn");
        if (rc)
-               goto err_rstn;
+               return rc;
 
-       if (gpio_is_valid(lp->slp_tr)) {
-               rc = gpio_request(lp->slp_tr, "slp_tr");
+       if (gpio_is_valid(pdata->slp_tr)) {
+               rc = gpio_request(pdata->slp_tr, "slp_tr");
                if (rc)
                        goto err_slp_tr;
        }
 
-       rc = gpio_direction_output(lp->rstn, 1);
+       rc = gpio_direction_output(pdata->rstn, 1);
        if (rc)
                goto err_gpio_dir;
 
-       if (gpio_is_valid(lp->slp_tr)) {
-               rc = gpio_direction_output(lp->slp_tr, 0);
+       if (gpio_is_valid(pdata->slp_tr)) {
+               rc = gpio_direction_output(pdata->slp_tr, 0);
                if (rc)
                        goto err_gpio_dir;
        }
 
        /* Reset */
        msleep(1);
-       gpio_set_value(lp->rstn, 0);
+       gpio_set_value(pdata->rstn, 0);
        msleep(1);
-       gpio_set_value(lp->rstn, 1);
+       gpio_set_value(pdata->rstn, 1);
        msleep(1);
 
-       rc = at86rf230_read_subreg(lp, SR_MAN_ID_0, &man_id_0);
-       if (rc)
-               goto err_gpio_dir;
-       rc = at86rf230_read_subreg(lp, SR_MAN_ID_1, &man_id_1);
-       if (rc)
+       rc = __at86rf230_detect_device(spi, &man_id, &part, &version);
+       if (rc < 0)
                goto err_gpio_dir;
 
-       if (man_id_1 != 0x00 || man_id_0 != 0x1f) {
+       if (man_id != 0x001f) {
                dev_err(&spi->dev, "Non-Atmel dev found (MAN_ID %02x %02x)\n",
-                       man_id_1, man_id_0);
+                       man_id >> 8, man_id & 0xFF);
                rc = -EINVAL;
                goto err_gpio_dir;
        }
 
-       rc = at86rf230_read_subreg(lp, SR_PART_NUM, &lp->part);
-       if (rc)
-               goto err_gpio_dir;
-
-       rc = at86rf230_read_subreg(lp, SR_VERSION_NUM, &lp->vers);
-       if (rc)
-               goto err_gpio_dir;
-
-       switch (lp->part) {
+       switch (part) {
        case 2:
                chip = "at86rf230";
-               /* supported = 1;  FIXME: should be easy to support; */
+               /* FIXME: should be easy to support; */
                break;
        case 3:
                chip = "at86rf231";
-               supported = 1;
+               ops = &at86rf230_ops;
+               break;
+       case 7:
+               chip = "at86rf212";
+               if (version == 1)
+                       ops = &at86rf212_ops;
                break;
        default:
                chip = "UNKNOWN";
                break;
        }
 
-       dev_info(&spi->dev, "Detected %s chip version %d\n", chip, lp->vers);
-       if (!supported) {
+       dev_info(&spi->dev, "Detected %s chip version %d\n", chip, version);
+       if (!ops) {
                rc = -ENOTSUPP;
                goto err_gpio_dir;
        }
 
+       dev = ieee802154_alloc_device(sizeof(*lp), ops);
+       if (!dev) {
+               rc = -ENOMEM;
+               goto err_gpio_dir;
+       }
+
+       lp = dev->priv;
+       lp->dev = dev;
+       lp->part = part;
+       lp->vers = version;
+
+       lp->spi = spi;
+
+       dev->parent = &spi->dev;
+       dev->extra_tx_headroom = 0;
+       dev->flags = IEEE802154_HW_OMIT_CKSUM | IEEE802154_HW_AACK;
+
+       if (pdata->irq_type & (IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING)) {
+               irq_worker = at86rf230_irqwork;
+               irq_handler = at86rf230_isr;
+       } else {
+               irq_worker = at86rf230_irqwork_level;
+               irq_handler = at86rf230_isr_level;
+       }
+
+       mutex_init(&lp->bmux);
+       INIT_WORK(&lp->irqwork, irq_worker);
+       spin_lock_init(&lp->lock);
+       init_completion(&lp->tx_complete);
+
+       spi_set_drvdata(spi, lp);
+
+       if (is_rf212(lp))
+               dev->phy->channels_supported[0] = 0x00007FF;
+       else
+               dev->phy->channels_supported[0] = 0x7FFF800;
+
        rc = at86rf230_hw_init(lp);
        if (rc)
-               goto err_gpio_dir;
+               goto err_hw_init;
 
        rc = request_irq(spi->irq, irq_handler,
                         IRQF_SHARED | pdata->irq_type,
                         dev_name(&spi->dev), lp);
        if (rc)
-               goto err_gpio_dir;
+               goto err_hw_init;
 
        /* Read irq status register to reset irq line */
        rc = at86rf230_read_subreg(lp, RG_IRQ_STATUS, 0xff, 0, &status);
@@ -980,30 +1067,33 @@ static int at86rf230_probe(struct spi_device *spi)
 
 err_irq:
        free_irq(spi->irq, lp);
+err_hw_init:
        flush_work(&lp->irqwork);
-err_gpio_dir:
-       if (gpio_is_valid(lp->slp_tr))
-               gpio_free(lp->slp_tr);
-err_slp_tr:
-       gpio_free(lp->rstn);
-err_rstn:
+       spi_set_drvdata(spi, NULL);
        mutex_destroy(&lp->bmux);
        ieee802154_free_device(lp->dev);
+
+err_gpio_dir:
+       if (gpio_is_valid(pdata->slp_tr))
+               gpio_free(pdata->slp_tr);
+err_slp_tr:
+       gpio_free(pdata->rstn);
        return rc;
 }
 
 static int at86rf230_remove(struct spi_device *spi)
 {
        struct at86rf230_local *lp = spi_get_drvdata(spi);
+       struct at86rf230_platform_data *pdata = spi->dev.platform_data;
 
        ieee802154_unregister_device(lp->dev);
 
        free_irq(spi->irq, lp);
        flush_work(&lp->irqwork);
 
-       if (gpio_is_valid(lp->slp_tr))
-               gpio_free(lp->slp_tr);
-       gpio_free(lp->rstn);
+       if (gpio_is_valid(pdata->slp_tr))
+               gpio_free(pdata->slp_tr);
+       gpio_free(pdata->rstn);
 
        mutex_destroy(&lp->bmux);
        ieee802154_free_device(lp->dev);