arm64: dts: meson-axg: add initial A113D SoC DT support

Try to add basic DT support for the Amlogic's Meson-AXG A113D SoC,
which describe components as follows: Reserve Memory, CPU, GIC, IRQ,
Timer, UART. It's capable of booting up into the serial console.

Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
index eacfb31..3d6b088 100644 (file)
--- a/arch/arm64/boot/dts/amlogic/Makefile
+++ b/arch/arm64/boot/dts/amlogic/Makefile
@@ -1,3 +1,4 @@
+dtb-$(CONFIG_ARCH_MESON) += meson-axg-s400.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-nanopi-k2.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-nexbox-a95x.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-odroidc2.dtb

diff --git a/arch/arm64/boot/dts/amlogic/meson-axg-s400.dts b/arch/arm64/boot/dts/amlogic/meson-axg-s400.dts
new file mode 100644 (file)
index 0000000..70eca1f
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-axg-s400.dts
@@ -0,0 +1,22 @@
+/*
+ * Copyright (c) 2017 Amlogic, Inc. All rights reserved.
+ *
+ * SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+ */
+
+/dts-v1/;
+
+#include "meson-axg.dtsi"
+
+/ {
+       compatible = "amlogic,s400", "amlogic,a113d", "amlogic,meson-axg";
+       model = "Amlogic Meson AXG S400 Development Board";
+
+       aliases {
+               serial0 = &uart_AO;
+       };
+};
+
+&uart_AO {
+       status = "okay";
+};

diff --git a/arch/arm64/boot/dts/amlogic/meson-axg.dtsi b/arch/arm64/boot/dts/amlogic/meson-axg.dtsi
new file mode 100644 (file)
index 0000000..0038328
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-axg.dtsi
@@ -0,0 +1,204 @@
+/*
+ * Copyright (c) 2017 Amlogic, Inc. All rights reserved.
+ *
+ * SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+       compatible = "amlogic,meson-axg";
+
+       interrupt-parent = <&gic>;
+       #address-cells = <2>;
+       #size-cells = <2>;
+
+       reserved-memory {
+               #address-cells = <2>;
+               #size-cells = <2>;
+               ranges;
+
+               /* 16 MiB reserved for Hardware ROM Firmware */
+               hwrom_reserved: hwrom@0 {
+                       reg = <0x0 0x0 0x0 0x1000000>;
+                       no-map;
+               };
+
+               /* Alternate 3 MiB reserved for ARM Trusted Firmware (BL31) */
+               secmon_reserved: secmon@05000000 {
+                       reg = <0x0 0x05000000 0x0 0x300000>;
+                       no-map;
+               };
+       };
+
+       cpus {
+               #address-cells = <0x2>;
+               #size-cells = <0x0>;
+
+               cpu0: cpu@0 {
+                       device_type = "cpu";
+                       compatible = "arm,cortex-a53", "arm,armv8";
+                       reg = <0x0 0x0>;
+                       enable-method = "psci";
+                       next-level-cache = <&l2>;
+               };
+
+               cpu1: cpu@1 {
+                       device_type = "cpu";
+                       compatible = "arm,cortex-a53", "arm,armv8";
+                       reg = <0x0 0x1>;
+                       enable-method = "psci";
+                       next-level-cache = <&l2>;
+               };
+
+               cpu2: cpu@2 {
+                       device_type = "cpu";
+                       compatible = "arm,cortex-a53", "arm,armv8";
+                       reg = <0x0 0x2>;
+                       enable-method = "psci";
+                       next-level-cache = <&l2>;
+               };
+
+               cpu3: cpu@3 {
+                       device_type = "cpu";
+                       compatible = "arm,cortex-a53", "arm,armv8";
+                       reg = <0x0 0x3>;
+                       enable-method = "psci";
+                       next-level-cache = <&l2>;
+               };
+
+               l2: l2-cache0 {
+                       compatible = "cache";
+               };
+       };
+
+       arm-pmu {
+               compatible = "arm,cortex-a53-pmu";
+               interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>,
+                            <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>,
+                            <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>,
+                            <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
+               interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
+       };
+
+       psci {
+               compatible = "arm,psci-1.0";
+               method = "smc";
+       };
+
+       timer {
+               compatible = "arm,armv8-timer";
+               interrupts = <GIC_PPI 13
+                       (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_LEVEL_LOW)>,
+                            <GIC_PPI 14
+                       (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_LEVEL_LOW)>,
+                            <GIC_PPI 11
+                       (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_LEVEL_LOW)>,
+                            <GIC_PPI 10
+                       (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_LEVEL_LOW)>;
+       };
+
+       xtal: xtal-clk {
+               compatible = "fixed-clock";
+               clock-frequency = <24000000>;
+               clock-output-names = "xtal";
+               #clock-cells = <0>;
+       };
+
+       soc {
+               compatible = "simple-bus";
+               #address-cells = <2>;
+               #size-cells = <2>;
+               ranges;
+
+               cbus: cbus@ffd00000 {
+                       compatible = "simple-bus";
+                       reg = <0x0 0xffd00000 0x0 0x25000>;
+                       #address-cells = <2>;
+                       #size-cells = <2>;
+                       ranges = <0x0 0x0 0x0 0xffd00000 0x0 0x25000>;
+
+                       uart_A: serial@24000 {
+                               compatible = "amlogic,meson-gx-uart", "amlogic,meson-uart";
+                               reg = <0x0 0x24000 0x0 0x14>;
+                               interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>;
+                               status = "disabled";
+                       };
+
+                       uart_B: serial@23000 {
+                               compatible = "amlogic,meson-gx-uart", "amlogic,meson-uart";
+                               reg = <0x0 0x23000 0x0 0x14>;
+                               interrupts = <GIC_SPI 75 IRQ_TYPE_EDGE_RISING>;
+                               status = "disabled";
+                       };
+               };
+
+               gic: interrupt-controller@ffc01000 {
+                       compatible = "arm,gic-400";
+                       reg = <0x0 0xffc01000 0 0x1000>,
+                             <0x0 0xffc02000 0 0x2000>,
+                             <0x0 0xffc04000 0 0x2000>,
+                             <0x0 0xffc06000 0 0x2000>;
+                       interrupt-controller;
+                       interrupts = <GIC_PPI 9
+                               (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_HIGH)>;
+                       #interrupt-cells = <3>;
+                       #address-cells = <0>;
+               };
+
+               mailbox: mailbox@ff63dc00 {
+                       compatible = "amlogic,meson-gx-mhu", "amlogic,meson-gxbb-mhu";
+                       reg = <0 0xff63dc00 0 0x400>;
+                       interrupts = <GIC_SPI 208 IRQ_TYPE_EDGE_RISING>,
+                                    <GIC_SPI 209 IRQ_TYPE_EDGE_RISING>,
+                                    <GIC_SPI 210 IRQ_TYPE_EDGE_RISING>;
+                       #mbox-cells = <1>;
+               };
+
+               sram: sram@fffc0000 {
+                       compatible = "amlogic,meson-axg-sram", "mmio-sram";
+                       reg = <0x0 0xfffc0000 0x0 0x20000>;
+                       #address-cells = <1>;
+                       #size-cells = <1>;
+                       ranges = <0 0x0 0xfffc0000 0x20000>;
+
+                       cpu_scp_lpri: scp-shmem@0 {
+                               compatible = "amlogic,meson-axg-scp-shmem";
+                               reg = <0x13000 0x400>;
+                       };
+
+                       cpu_scp_hpri: scp-shmem@200 {
+                               compatible = "amlogic,meson-axg-scp-shmem";
+                               reg = <0x13400 0x400>;
+                       };
+               };
+
+               aobus: aobus@ff800000 {
+                       compatible = "simple-bus";
+                       reg = <0x0 0xff800000 0x0 0x100000>;
+                       #address-cells = <2>;
+                       #size-cells = <2>;
+                       ranges = <0x0 0x0 0x0 0xff800000 0x0 0x100000>;
+
+                       uart_AO: serial@3000 {
+                               compatible = "amlogic,meson-gx-uart", "amlogic,meson-ao-uart";
+                               reg = <0x0 0x3000 0x0 0x18>;
+                               interrupts = <GIC_SPI 193 IRQ_TYPE_EDGE_RISING>;
+                               clocks = <&xtal>, <&xtal>, <&xtal>;
+                               clock-names = "xtal", "pclk", "baud";
+                               status = "disabled";
+                       };
+
+                       uart_AO_B: serial@4000 {
+                               compatible = "amlogic,meson-gx-uart", "amlogic,meson-ao-uart";
+                               reg = <0x0 0x4000 0x0 0x18>;
+                               interrupts = <GIC_SPI 197 IRQ_TYPE_EDGE_RISING>;
+                               clocks = <&xtal>, <&xtal>, <&xtal>;
+                               clock-names = "xtal", "pclk", "baud";
+                               status = "disabled";
+                       };
+               };
+       };
+};