#define MII_BUSY 0x00000001
#define MII_WRITE 0x00000002
+/* GMAC4 defines */
+#define MII_GMAC4_GOC_SHIFT 2
+#define MII_GMAC4_WRITE (1 << MII_GMAC4_GOC_SHIFT)
+#define MII_GMAC4_READ (3 << MII_GMAC4_GOC_SHIFT)
+
+#define MII_PHY_ADDR_GMAC4_SHIFT 21
+#define MII_PHY_ADDR_GMAC4_MASK GENMASK(25, 21)
+#define MII_PHY_REG_GMAC4_SHIFT 16
+#define MII_PHY_REG_GMAC4_MASK GENMASK(20, 16)
+#define MII_CSR_CLK_GMAC4_SHIFT 8
+#define MII_CSR_CLK_GMAC4_MASK GENMASK(11, 8)
+
static int stmmac_mdio_busy_wait(void __iomem *ioaddr, unsigned int mii_addr)
{
unsigned long curr;
}
/**
+ * stmmac_mdio_read_gmac4
+ * @bus: points to the mii_bus structure
+ * @phyaddr: MII addr reg bits 25-21
+ * @phyreg: MII addr reg bits 20-16
+ * Description: it reads data from the MII register of GMAC4 from within
+ * the phy device.
+ */
+static int stmmac_mdio_read_gmac4(struct mii_bus *bus, int phyaddr, int phyreg)
+{
+ struct net_device *ndev = bus->priv;
+ struct stmmac_priv *priv = netdev_priv(ndev);
+ unsigned int mii_address = priv->hw->mii.addr;
+ unsigned int mii_data = priv->hw->mii.data;
+ int data;
+ u32 value = (((phyaddr << MII_PHY_ADDR_GMAC4_SHIFT) &
+ (MII_PHY_ADDR_GMAC4_MASK)) |
+ ((phyreg << MII_PHY_REG_GMAC4_SHIFT) &
+ (MII_PHY_REG_GMAC4_MASK))) | MII_GMAC4_READ;
+
+ value |= MII_BUSY | ((priv->clk_csr & MII_CSR_CLK_GMAC4_MASK)
+ << MII_CSR_CLK_GMAC4_SHIFT);
+
+ if (stmmac_mdio_busy_wait(priv->ioaddr, mii_address))
+ return -EBUSY;
+
+ writel(value, priv->ioaddr + mii_address);
+
+ if (stmmac_mdio_busy_wait(priv->ioaddr, mii_address))
+ return -EBUSY;
+
+ /* Read the data from the MII data register */
+ data = (int)readl(priv->ioaddr + mii_data);
+
+ return data;
+}
+
+/**
+ * stmmac_mdio_write_gmac4
+ * @bus: points to the mii_bus structure
+ * @phyaddr: MII addr reg bits 25-21
+ * @phyreg: MII addr reg bits 20-16
+ * @phydata: phy data
+ * Description: it writes the data into the MII register of GMAC4 from within
+ * the device.
+ */
+static int stmmac_mdio_write_gmac4(struct mii_bus *bus, int phyaddr, int phyreg,
+ u16 phydata)
+{
+ struct net_device *ndev = bus->priv;
+ struct stmmac_priv *priv = netdev_priv(ndev);
+ unsigned int mii_address = priv->hw->mii.addr;
+ unsigned int mii_data = priv->hw->mii.data;
+
+ u32 value = (((phyaddr << MII_PHY_ADDR_GMAC4_SHIFT) &
+ (MII_PHY_ADDR_GMAC4_MASK)) |
+ ((phyreg << MII_PHY_REG_GMAC4_SHIFT) &
+ (MII_PHY_REG_GMAC4_MASK))) | MII_GMAC4_WRITE;
+
+ value |= MII_BUSY | ((priv->clk_csr & MII_CSR_CLK_GMAC4_MASK)
+ << MII_CSR_CLK_GMAC4_SHIFT);
+
+ /* Wait until any existing MII operation is complete */
+ if (stmmac_mdio_busy_wait(priv->ioaddr, mii_address))
+ return -EBUSY;
+
+ /* Set the MII address register to write */
+ writel(phydata, priv->ioaddr + mii_data);
+ writel(value, priv->ioaddr + mii_address);
+
+ /* Wait until any existing MII operation is complete */
+ return stmmac_mdio_busy_wait(priv->ioaddr, mii_address);
+}
+
+/**
* stmmac_mdio_reset
* @bus: points to the mii_bus structure
* Description: reset the MII bus
/* This is a workaround for problems with the STE101P PHY.
* It doesn't complete its reset until at least one clock cycle
- * on MDC, so perform a dummy mdio read.
+ * on MDC, so perform a dummy mdio read. To be upadted for GMAC4
+ * if needed.
*/
- writel(0, priv->ioaddr + mii_address);
+ if (!priv->plat->has_gmac4)
+ writel(0, priv->ioaddr + mii_address);
#endif
return 0;
}
#endif
new_bus->name = "stmmac";
- new_bus->read = &stmmac_mdio_read;
- new_bus->write = &stmmac_mdio_write;
+ if (priv->plat->has_gmac4) {
+ new_bus->read = &stmmac_mdio_read_gmac4;
+ new_bus->write = &stmmac_mdio_write_gmac4;
+ } else {
+ new_bus->read = &stmmac_mdio_read;
+ new_bus->write = &stmmac_mdio_write;
+ }
+
new_bus->reset = &stmmac_mdio_reset;
snprintf(new_bus->id, MII_BUS_ID_SIZE, "%s-%x",
new_bus->name, priv->plat->bus_id);