unsigned int tx_csum_limit;
struct phylink *phylink;
struct phylink_config phylink_config;
+ struct phylink_pcs phylink_pcs;
struct phy *comphy;
struct mvneta_bm *bm_priv;
return 0;
}
-static void mvneta_validate(struct phylink_config *config,
- unsigned long *supported,
- struct phylink_link_state *state)
+static struct mvneta_port *mvneta_pcs_to_port(struct phylink_pcs *pcs)
{
- /* We only support QSGMII, SGMII, 802.3z and RGMII modes.
- * When in 802.3z mode, we must have AN enabled:
- * "Bit 2 Field InBandAnEn In-band Auto-Negotiation enable. ...
- * When <PortType> = 1 (1000BASE-X) this field must be set to 1."
- */
- if (phy_interface_mode_is_8023z(state->interface) &&
- !phylink_test(state->advertising, Autoneg)) {
- linkmode_zero(supported);
- return;
- }
-
- phylink_generic_validate(config, supported, state);
+ return container_of(pcs, struct mvneta_port, phylink_pcs);
}
-static void mvneta_mac_pcs_get_state(struct phylink_config *config,
- struct phylink_link_state *state)
+static void mvneta_pcs_get_state(struct phylink_pcs *pcs,
+ struct phylink_link_state *state)
{
- struct net_device *ndev = to_net_dev(config->dev);
- struct mvneta_port *pp = netdev_priv(ndev);
+ struct mvneta_port *pp = mvneta_pcs_to_port(pcs);
u32 gmac_stat;
gmac_stat = mvreg_read(pp, MVNETA_GMAC_STATUS);
state->link = !!(gmac_stat & MVNETA_GMAC_LINK_UP);
state->duplex = !!(gmac_stat & MVNETA_GMAC_FULL_DUPLEX);
- state->pause = 0;
if (gmac_stat & MVNETA_GMAC_RX_FLOW_CTRL_ENABLE)
state->pause |= MLO_PAUSE_RX;
if (gmac_stat & MVNETA_GMAC_TX_FLOW_CTRL_ENABLE)
state->pause |= MLO_PAUSE_TX;
}
-static void mvneta_mac_an_restart(struct phylink_config *config)
+static int mvneta_pcs_config(struct phylink_pcs *pcs,
+ unsigned int mode, phy_interface_t interface,
+ const unsigned long *advertising,
+ bool permit_pause_to_mac)
{
- struct net_device *ndev = to_net_dev(config->dev);
- struct mvneta_port *pp = netdev_priv(ndev);
+ struct mvneta_port *pp = mvneta_pcs_to_port(pcs);
+ u32 mask, val, an, old_an, changed;
+
+ mask = MVNETA_GMAC_INBAND_AN_ENABLE |
+ MVNETA_GMAC_INBAND_RESTART_AN |
+ MVNETA_GMAC_AN_SPEED_EN |
+ MVNETA_GMAC_AN_FLOW_CTRL_EN |
+ MVNETA_GMAC_AN_DUPLEX_EN;
+
+ if (phylink_autoneg_inband(mode)) {
+ mask |= MVNETA_GMAC_CONFIG_MII_SPEED |
+ MVNETA_GMAC_CONFIG_GMII_SPEED |
+ MVNETA_GMAC_CONFIG_FULL_DUPLEX;
+ val = MVNETA_GMAC_INBAND_AN_ENABLE;
+
+ if (interface == PHY_INTERFACE_MODE_SGMII) {
+ /* SGMII mode receives the speed and duplex from PHY */
+ val |= MVNETA_GMAC_AN_SPEED_EN |
+ MVNETA_GMAC_AN_DUPLEX_EN;
+ } else {
+ /* 802.3z mode has fixed speed and duplex */
+ val |= MVNETA_GMAC_CONFIG_GMII_SPEED |
+ MVNETA_GMAC_CONFIG_FULL_DUPLEX;
+
+ /* The FLOW_CTRL_EN bit selects either the hardware
+ * automatically or the CONFIG_FLOW_CTRL manually
+ * controls the GMAC pause mode.
+ */
+ if (permit_pause_to_mac)
+ val |= MVNETA_GMAC_AN_FLOW_CTRL_EN;
+
+ /* Update the advertisement bits */
+ mask |= MVNETA_GMAC_ADVERT_SYM_FLOW_CTRL;
+ if (phylink_test(advertising, Pause))
+ val |= MVNETA_GMAC_ADVERT_SYM_FLOW_CTRL;
+ }
+ } else {
+ /* Phy or fixed speed - disable in-band AN modes */
+ val = 0;
+ }
+
+ old_an = an = mvreg_read(pp, MVNETA_GMAC_AUTONEG_CONFIG);
+ an = (an & ~mask) | val;
+ changed = old_an ^ an;
+ if (changed)
+ mvreg_write(pp, MVNETA_GMAC_AUTONEG_CONFIG, an);
+
+ /* We are only interested in the advertisement bits changing */
+ return !!(changed & MVNETA_GMAC_ADVERT_SYM_FLOW_CTRL);
+}
+
+static void mvneta_pcs_an_restart(struct phylink_pcs *pcs)
+{
+ struct mvneta_port *pp = mvneta_pcs_to_port(pcs);
u32 gmac_an = mvreg_read(pp, MVNETA_GMAC_AUTONEG_CONFIG);
mvreg_write(pp, MVNETA_GMAC_AUTONEG_CONFIG,
gmac_an & ~MVNETA_GMAC_INBAND_RESTART_AN);
}
+static const struct phylink_pcs_ops mvneta_phylink_pcs_ops = {
+ .pcs_get_state = mvneta_pcs_get_state,
+ .pcs_config = mvneta_pcs_config,
+ .pcs_an_restart = mvneta_pcs_an_restart,
+};
+
+static void mvneta_validate(struct phylink_config *config,
+ unsigned long *supported,
+ struct phylink_link_state *state)
+{
+ /* We only support QSGMII, SGMII, 802.3z and RGMII modes.
+ * When in 802.3z mode, we must have AN enabled:
+ * "Bit 2 Field InBandAnEn In-band Auto-Negotiation enable. ...
+ * When <PortType> = 1 (1000BASE-X) this field must be set to 1."
+ */
+ if (phy_interface_mode_is_8023z(state->interface) &&
+ !phylink_test(state->advertising, Autoneg)) {
+ linkmode_zero(supported);
+ return;
+ }
+
+ phylink_generic_validate(config, supported, state);
+}
+
static int mvneta_mac_prepare(struct phylink_config *config, unsigned int mode,
phy_interface_t interface)
{
u32 new_ctrl0, gmac_ctrl0 = mvreg_read(pp, MVNETA_GMAC_CTRL_0);
u32 new_ctrl2, gmac_ctrl2 = mvreg_read(pp, MVNETA_GMAC_CTRL_2);
u32 new_ctrl4, gmac_ctrl4 = mvreg_read(pp, MVNETA_GMAC_CTRL_4);
- u32 new_an, gmac_an = mvreg_read(pp, MVNETA_GMAC_AUTONEG_CONFIG);
new_ctrl0 = gmac_ctrl0 & ~MVNETA_GMAC0_PORT_1000BASE_X;
new_ctrl2 = gmac_ctrl2 & ~(MVNETA_GMAC2_INBAND_AN_ENABLE |
MVNETA_GMAC2_PORT_RESET);
new_ctrl4 = gmac_ctrl4 & ~(MVNETA_GMAC4_SHORT_PREAMBLE_ENABLE);
- new_an = gmac_an & ~(MVNETA_GMAC_INBAND_AN_ENABLE |
- MVNETA_GMAC_INBAND_RESTART_AN |
- MVNETA_GMAC_AN_SPEED_EN |
- MVNETA_GMAC_ADVERT_SYM_FLOW_CTRL |
- MVNETA_GMAC_AN_FLOW_CTRL_EN |
- MVNETA_GMAC_AN_DUPLEX_EN);
/* Even though it might look weird, when we're configured in
* SGMII or QSGMII mode, the RGMII bit needs to be set.
phy_interface_mode_is_8023z(state->interface))
new_ctrl2 |= MVNETA_GMAC2_PCS_ENABLE;
- if (phylink_test(state->advertising, Pause))
- new_an |= MVNETA_GMAC_ADVERT_SYM_FLOW_CTRL;
-
if (!phylink_autoneg_inband(mode)) {
/* Phy or fixed speed - nothing to do, leave the
* configured speed, duplex and flow control as-is.
} else if (state->interface == PHY_INTERFACE_MODE_SGMII) {
/* SGMII mode receives the state from the PHY */
new_ctrl2 |= MVNETA_GMAC2_INBAND_AN_ENABLE;
- new_an = (new_an & ~(MVNETA_GMAC_CONFIG_MII_SPEED |
- MVNETA_GMAC_CONFIG_GMII_SPEED |
- MVNETA_GMAC_CONFIG_FULL_DUPLEX)) |
- MVNETA_GMAC_INBAND_AN_ENABLE |
- MVNETA_GMAC_AN_SPEED_EN |
- MVNETA_GMAC_AN_DUPLEX_EN;
} else {
/* 802.3z negotiation - only 1000base-X */
new_ctrl0 |= MVNETA_GMAC0_PORT_1000BASE_X;
- new_an = (new_an & ~MVNETA_GMAC_CONFIG_MII_SPEED) |
- MVNETA_GMAC_INBAND_AN_ENABLE |
- MVNETA_GMAC_CONFIG_GMII_SPEED |
- /* The MAC only supports FD mode */
- MVNETA_GMAC_CONFIG_FULL_DUPLEX;
-
- if (state->pause & MLO_PAUSE_AN && state->an_enabled)
- new_an |= MVNETA_GMAC_AN_FLOW_CTRL_EN;
}
/* When at 2.5G, the link partner can send frames with shortened
mvreg_write(pp, MVNETA_GMAC_CTRL_2, new_ctrl2);
if (new_ctrl4 != gmac_ctrl4)
mvreg_write(pp, MVNETA_GMAC_CTRL_4, new_ctrl4);
- if (new_an != gmac_an)
- mvreg_write(pp, MVNETA_GMAC_AUTONEG_CONFIG, new_an);
if (gmac_ctrl2 & MVNETA_GMAC2_PORT_RESET) {
while ((mvreg_read(pp, MVNETA_GMAC_CTRL_2) &
static const struct phylink_mac_ops mvneta_phylink_ops = {
.validate = mvneta_validate,
- .mac_pcs_get_state = mvneta_mac_pcs_get_state,
- .mac_an_restart = mvneta_mac_an_restart,
.mac_prepare = mvneta_mac_prepare,
.mac_config = mvneta_mac_config,
.mac_finish = mvneta_mac_finish,
pp->phylink_config.dev = &dev->dev;
pp->phylink_config.type = PHYLINK_NETDEV;
- pp->phylink_config.legacy_pre_march2020 = true;
pp->phylink_config.mac_capabilities = MAC_SYM_PAUSE | MAC_10 |
MAC_100 | MAC_1000FD | MAC_2500FD;
goto err_clk;
}
+ pp->phylink_pcs.ops = &mvneta_phylink_pcs_ops;
+ phylink_set_pcs(phylink, &pp->phylink_pcs);
+
/* Alloc per-cpu port structure */
pp->ports = alloc_percpu(struct mvneta_pcpu_port);
if (!pp->ports) {
OSDN Git Service
