static int e1000_get_link_ksettings(struct net_device *netdev,
struct ethtool_link_ksettings *cmd)
{
+ u32 speed, supported, advertising, lp_advertising, lpa_t;
struct e1000_adapter *adapter = netdev_priv(netdev);
struct e1000_hw *hw = &adapter->hw;
- u32 speed, supported, advertising;
if (hw->phy.media_type == e1000_media_type_copper) {
supported = (SUPPORTED_10baseT_Half |
SUPPORTED_100baseT_Half |
SUPPORTED_100baseT_Full |
SUPPORTED_1000baseT_Full |
+ SUPPORTED_Asym_Pause |
SUPPORTED_Autoneg |
+ SUPPORTED_Pause |
SUPPORTED_TP);
if (hw->phy.type == e1000_phy_ife)
supported &= ~SUPPORTED_1000baseT_Full;
if (hw->phy.media_type != e1000_media_type_copper)
cmd->base.eth_tp_mdix_ctrl = ETH_TP_MDI_INVALID;
+ lpa_t = mii_stat1000_to_ethtool_lpa_t(adapter->phy_regs.stat1000);
+ lp_advertising = lpa_t |
+ mii_lpa_to_ethtool_lpa_t(adapter->phy_regs.lpa);
+
ethtool_convert_legacy_u32_to_link_mode(cmd->link_modes.supported,
supported);
ethtool_convert_legacy_u32_to_link_mode(cmd->link_modes.advertising,
advertising);
+ ethtool_convert_legacy_u32_to_link_mode(cmd->link_modes.lp_advertising,
+ lp_advertising);
return 0;
}
/* Copyright(c) 1999 - 2018 Intel Corporation. */
#include "e1000.h"
+#include <linux/ethtool.h>
static s32 e1000_wait_autoneg(struct e1000_hw *hw);
static s32 e1000_access_phy_wakeup_reg_bm(struct e1000_hw *hw, u32 offset,
*/
mii_autoneg_adv_reg &=
~(ADVERTISE_PAUSE_ASYM | ADVERTISE_PAUSE_CAP);
+ phy->autoneg_advertised &=
+ ~(ADVERTISED_Pause | ADVERTISED_Asym_Pause);
break;
case e1000_fc_rx_pause:
/* Rx Flow control is enabled, and Tx Flow control is
*/
mii_autoneg_adv_reg |=
(ADVERTISE_PAUSE_ASYM | ADVERTISE_PAUSE_CAP);
+ phy->autoneg_advertised |=
+ (ADVERTISED_Pause | ADVERTISED_Asym_Pause);
break;
case e1000_fc_tx_pause:
/* Tx Flow control is enabled, and Rx Flow control is
*/
mii_autoneg_adv_reg |= ADVERTISE_PAUSE_ASYM;
mii_autoneg_adv_reg &= ~ADVERTISE_PAUSE_CAP;
+ phy->autoneg_advertised |= ADVERTISED_Asym_Pause;
+ phy->autoneg_advertised &= ~ADVERTISED_Pause;
break;
case e1000_fc_full:
/* Flow control (both Rx and Tx) is enabled by a software
*/
mii_autoneg_adv_reg |=
(ADVERTISE_PAUSE_ASYM | ADVERTISE_PAUSE_CAP);
+ phy->autoneg_advertised |=
+ (ADVERTISED_Pause | ADVERTISED_Asym_Pause);
break;
default:
e_dbg("Flow control param set incorrectly\n");