Emit a trace event when a GPIO change its state.
Example booting obmc-phosphor-image:
$ qemu-system-arm -M witherspoon-bmc -trace pca955x_gpio_change
1592690552.687372:pca955x_gpio_change pca1 GPIO id:0 status: 0 -> 1
1592690552.690169:pca955x_gpio_change pca1 GPIO id:1 status: 0 -> 1
1592690552.691673:pca955x_gpio_change pca1 GPIO id:2 status: 0 -> 1
1592690552.696886:pca955x_gpio_change pca1 GPIO id:3 status: 0 -> 1
1592690552.698614:pca955x_gpio_change pca1 GPIO id:13 status: 0 -> 1
1592690552.699833:pca955x_gpio_change pca1 GPIO id:14 status: 0 -> 1
1592690552.700842:pca955x_gpio_change pca1 GPIO id:15 status: 0 -> 1
1592690683.841921:pca955x_gpio_change pca1 GPIO id:14 status: 1 -> 0
1592690683.861660:pca955x_gpio_change pca1 GPIO id:14 status: 0 -> 1
1592690684.371460:pca955x_gpio_change pca1 GPIO id:14 status: 1 -> 0
1592690684.882115:pca955x_gpio_change pca1 GPIO id:14 status: 0 -> 1
1592690685.391411:pca955x_gpio_change pca1 GPIO id:14 status: 1 -> 0
1592690685.901391:pca955x_gpio_change pca1 GPIO id:14 status: 0 -> 1
1592690686.411678:pca955x_gpio_change pca1 GPIO id:14 status: 1 -> 0
1592690686.921279:pca955x_gpio_change pca1 GPIO id:14 status: 0 -> 1
We notice the GPIO #14 (front-power LED) starts to blink.
This LED is described in the witherspoon device-tree [*]:
front-power {
retain-state-shutdown;
default-state = "keep";
gpios = <&pca0 14 GPIO_ACTIVE_LOW>;
};
[*] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/arch/arm/boot/dts/aspeed-bmc-opp-witherspoon.dts?id=
b1f9be9392f0#n140
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Cédric Le Goater <clg@kaod.org>
Message-id:
20200623072723.6324-9-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
buf[i] = '\0';
trace_pca955x_gpio_status(s->description, buf);
}
+ if (trace_event_get_state_backends(TRACE_PCA955X_GPIO_CHANGE)) {
+ for (i = 0; i < k->pin_count; i++) {
+ if (extract32(pins_changed, i, 1)) {
+ unsigned new_state = extract32(pins_status, i, 1);
+
+ /*
+ * We display the state using the PCA logic ("active-high").
+ * This is not the state of the LED, which signal might be
+ * wired "active-low" on the board.
+ */
+ trace_pca955x_gpio_change(s->description, i,
+ !new_state, new_state);
+ }
+ }
+ }
}
static void pca955x_update_pin_input(PCA955xState *s)
# pca9552.c
pca955x_gpio_status(const char *description, const char *buf) "%s GPIOs 0-15 [%s]"
+pca955x_gpio_change(const char *description, unsigned id, unsigned prev_state, unsigned current_state) "%s GPIO id:%u status: %u -> %u"