#define _AB8500_CHARGER_H_
#include <linux/kernel.h>
-#include <linux/mfd/abx500.h>
/*
* System control 2 register offsets.
#define BUS_PP_PRECHG_CURRENT_MASK 0x0E
#define BUS_POWER_PATH_PRECHG_ENA 0x01
+/*
+ * ADC for the battery thermistor.
+ * When using the ABx500_ADC_THERM_BATCTRL the battery ID resistor is combined
+ * with a NTC resistor to both identify the battery and to measure its
+ * temperature. Different phone manufactures uses different techniques to both
+ * identify the battery and to read its temperature.
+ */
+enum abx500_adc_therm {
+ ABx500_ADC_THERM_BATCTRL,
+ ABx500_ADC_THERM_BATTEMP,
+};
+
+/**
+ * struct abx500_res_to_temp - defines one point in a temp to res curve. To
+ * be used in battery packs that combines the identification resistor with a
+ * NTC resistor.
+ * @temp: battery pack temperature in Celsius
+ * @resist: NTC resistor net total resistance
+ */
+struct abx500_res_to_temp {
+ int temp;
+ int resist;
+};
+
+/**
+ * struct abx500_v_to_cap - Table for translating voltage to capacity
+ * @voltage: Voltage in mV
+ * @capacity: Capacity in percent
+ */
+struct abx500_v_to_cap {
+ int voltage;
+ int capacity;
+};
+
+/* Forward declaration */
+struct abx500_fg;
+
+/**
+ * struct abx500_fg_parameters - Fuel gauge algorithm parameters, in seconds
+ * if not specified
+ * @recovery_sleep_timer: Time between measurements while recovering
+ * @recovery_total_time: Total recovery time
+ * @init_timer: Measurement interval during startup
+ * @init_discard_time: Time we discard voltage measurement at startup
+ * @init_total_time: Total init time during startup
+ * @high_curr_time: Time current has to be high to go to recovery
+ * @accu_charging: FG accumulation time while charging
+ * @accu_high_curr: FG accumulation time in high current mode
+ * @high_curr_threshold: High current threshold, in mA
+ * @lowbat_threshold: Low battery threshold, in mV
+ * @overbat_threshold: Over battery threshold, in mV
+ * @battok_falling_th_sel0 Threshold in mV for battOk signal sel0
+ * Resolution in 50 mV step.
+ * @battok_raising_th_sel1 Threshold in mV for battOk signal sel1
+ * Resolution in 50 mV step.
+ * @user_cap_limit Capacity reported from user must be within this
+ * limit to be considered as sane, in percentage
+ * points.
+ * @maint_thres This is the threshold where we stop reporting
+ * battery full while in maintenance, in per cent
+ * @pcut_enable: Enable power cut feature in ab8505
+ * @pcut_max_time: Max time threshold
+ * @pcut_flag_time: Flagtime threshold
+ * @pcut_max_restart: Max number of restarts
+ * @pcut_debounce_time: Sets battery debounce time
+ */
+struct abx500_fg_parameters {
+ int recovery_sleep_timer;
+ int recovery_total_time;
+ int init_timer;
+ int init_discard_time;
+ int init_total_time;
+ int high_curr_time;
+ int accu_charging;
+ int accu_high_curr;
+ int high_curr_threshold;
+ int lowbat_threshold;
+ int overbat_threshold;
+ int battok_falling_th_sel0;
+ int battok_raising_th_sel1;
+ int user_cap_limit;
+ int maint_thres;
+ bool pcut_enable;
+ u8 pcut_max_time;
+ u8 pcut_flag_time;
+ u8 pcut_max_restart;
+ u8 pcut_debounce_time;
+};
+
+/**
+ * struct abx500_charger_maximization - struct used by the board config.
+ * @use_maxi: Enable maximization for this battery type
+ * @maxi_chg_curr: Maximum charger current allowed
+ * @maxi_wait_cycles: cycles to wait before setting charger current
+ * @charger_curr_step delta between two charger current settings (mA)
+ */
+struct abx500_maxim_parameters {
+ bool ena_maxi;
+ int chg_curr;
+ int wait_cycles;
+ int charger_curr_step;
+};
+
+/**
+ * struct abx500_battery_type - different batteries supported
+ * @name: battery technology
+ * @resis_high: battery upper resistance limit
+ * @resis_low: battery lower resistance limit
+ * @charge_full_design: Maximum battery capacity in mAh
+ * @nominal_voltage: Nominal voltage of the battery in mV
+ * @termination_vol: max voltage upto which battery can be charged
+ * @termination_curr battery charging termination current in mA
+ * @recharge_cap battery capacity limit that will trigger a new
+ * full charging cycle in the case where maintenan-
+ * -ce charging has been disabled
+ * @normal_cur_lvl: charger current in normal state in mA
+ * @normal_vol_lvl: charger voltage in normal state in mV
+ * @maint_a_cur_lvl: charger current in maintenance A state in mA
+ * @maint_a_vol_lvl: charger voltage in maintenance A state in mV
+ * @maint_a_chg_timer_h: charge time in maintenance A state
+ * @maint_b_cur_lvl: charger current in maintenance B state in mA
+ * @maint_b_vol_lvl: charger voltage in maintenance B state in mV
+ * @maint_b_chg_timer_h: charge time in maintenance B state
+ * @low_high_cur_lvl: charger current in temp low/high state in mA
+ * @low_high_vol_lvl: charger voltage in temp low/high state in mV'
+ * @battery_resistance: battery inner resistance in mOhm.
+ * @n_r_t_tbl_elements: number of elements in r_to_t_tbl
+ * @r_to_t_tbl: table containing resistance to temp points
+ * @n_v_cap_tbl_elements: number of elements in v_to_cap_tbl
+ * @v_to_cap_tbl: Voltage to capacity (in %) table
+ * @n_batres_tbl_elements number of elements in the batres_tbl
+ * @batres_tbl battery internal resistance vs temperature table
+ */
+struct abx500_battery_type {
+ int name;
+ int resis_high;
+ int resis_low;
+ int charge_full_design;
+ int nominal_voltage;
+ int termination_vol;
+ int termination_curr;
+ int recharge_cap;
+ int normal_cur_lvl;
+ int normal_vol_lvl;
+ int maint_a_cur_lvl;
+ int maint_a_vol_lvl;
+ int maint_a_chg_timer_h;
+ int maint_b_cur_lvl;
+ int maint_b_vol_lvl;
+ int maint_b_chg_timer_h;
+ int low_high_cur_lvl;
+ int low_high_vol_lvl;
+ int battery_resistance;
+ int n_temp_tbl_elements;
+ const struct abx500_res_to_temp *r_to_t_tbl;
+ int n_v_cap_tbl_elements;
+ const struct abx500_v_to_cap *v_to_cap_tbl;
+ int n_batres_tbl_elements;
+ const struct batres_vs_temp *batres_tbl;
+};
+
+/**
+ * struct abx500_bm_capacity_levels - abx500 capacity level data
+ * @critical: critical capacity level in percent
+ * @low: low capacity level in percent
+ * @normal: normal capacity level in percent
+ * @high: high capacity level in percent
+ * @full: full capacity level in percent
+ */
+struct abx500_bm_capacity_levels {
+ int critical;
+ int low;
+ int normal;
+ int high;
+ int full;
+};
+
+/**
+ * struct abx500_bm_charger_parameters - Charger specific parameters
+ * @usb_volt_max: maximum allowed USB charger voltage in mV
+ * @usb_curr_max: maximum allowed USB charger current in mA
+ * @ac_volt_max: maximum allowed AC charger voltage in mV
+ * @ac_curr_max: maximum allowed AC charger current in mA
+ */
+struct abx500_bm_charger_parameters {
+ int usb_volt_max;
+ int usb_curr_max;
+ int ac_volt_max;
+ int ac_curr_max;
+};
+
+/**
+ * struct abx500_bm_data - abx500 battery management data
+ * @temp_under under this temp, charging is stopped
+ * @temp_low between this temp and temp_under charging is reduced
+ * @temp_high between this temp and temp_over charging is reduced
+ * @temp_over over this temp, charging is stopped
+ * @temp_now present battery temperature
+ * @temp_interval_chg temperature measurement interval in s when charging
+ * @temp_interval_nochg temperature measurement interval in s when not charging
+ * @main_safety_tmr_h safety timer for main charger
+ * @usb_safety_tmr_h safety timer for usb charger
+ * @bkup_bat_v voltage which we charge the backup battery with
+ * @bkup_bat_i current which we charge the backup battery with
+ * @no_maintenance indicates that maintenance charging is disabled
+ * @capacity_scaling indicates whether capacity scaling is to be used
+ * @abx500_adc_therm placement of thermistor, batctrl or battemp adc
+ * @chg_unknown_bat flag to enable charging of unknown batteries
+ * @enable_overshoot flag to enable VBAT overshoot control
+ * @auto_trig flag to enable auto adc trigger
+ * @fg_res resistance of FG resistor in 0.1mOhm
+ * @n_btypes number of elements in array bat_type
+ * @batt_id index of the identified battery in array bat_type
+ * @interval_charging charge alg cycle period time when charging (sec)
+ * @interval_not_charging charge alg cycle period time when not charging (sec)
+ * @temp_hysteresis temperature hysteresis
+ * @gnd_lift_resistance Battery ground to phone ground resistance (mOhm)
+ * @n_chg_out_curr number of elements in array chg_output_curr
+ * @n_chg_in_curr number of elements in array chg_input_curr
+ * @chg_output_curr charger output current level map
+ * @chg_input_curr charger input current level map
+ * @maxi maximization parameters
+ * @cap_levels capacity in percent for the different capacity levels
+ * @bat_type table of supported battery types
+ * @chg_params charger parameters
+ * @fg_params fuel gauge parameters
+ */
+struct abx500_bm_data {
+ int temp_under;
+ int temp_low;
+ int temp_high;
+ int temp_over;
+ int temp_now;
+ int temp_interval_chg;
+ int temp_interval_nochg;
+ int main_safety_tmr_h;
+ int usb_safety_tmr_h;
+ int bkup_bat_v;
+ int bkup_bat_i;
+ bool autopower_cfg;
+ bool ac_enabled;
+ bool usb_enabled;
+ bool no_maintenance;
+ bool capacity_scaling;
+ bool chg_unknown_bat;
+ bool enable_overshoot;
+ bool auto_trig;
+ enum abx500_adc_therm adc_therm;
+ int fg_res;
+ int n_btypes;
+ int batt_id;
+ int interval_charging;
+ int interval_not_charging;
+ int temp_hysteresis;
+ int gnd_lift_resistance;
+ int n_chg_out_curr;
+ int n_chg_in_curr;
+ int *chg_output_curr;
+ int *chg_input_curr;
+ const struct abx500_maxim_parameters *maxi;
+ const struct abx500_bm_capacity_levels *cap_levels;
+ struct abx500_battery_type *bat_type;
+ const struct abx500_bm_charger_parameters *chg_params;
+ const struct abx500_fg_parameters *fg_params;
+};
+
+enum {
+ NTC_EXTERNAL = 0,
+ NTC_INTERNAL,
+};
+
/**
* struct res_to_temp - defines one point in a temp to res curve. To
* be used in battery packs that combines the identification resistor with a
const struct ab8500_fg_parameters *fg_params;
};
-struct ab8500_btemp;
-struct ab8500_fg;
-
extern struct abx500_bm_data ab8500_bm_data;
void ab8500_charger_usb_state_changed(u8 bm_usb_state, u16 mA);
int ab8500_fg_inst_curr_finalize(struct ab8500_fg *di, int *res);
int ab8500_fg_inst_curr_started(struct ab8500_fg *di);
int ab8500_fg_inst_curr_done(struct ab8500_fg *di);
+int ab8500_bm_of_probe(struct device *dev,
+ struct device_node *np,
+ struct abx500_bm_data *bm);
#endif /* _AB8500_CHARGER_H_ */
u8 setting;
};
-/* Battery driver related data */
-/*
- * ADC for the battery thermistor.
- * When using the ABx500_ADC_THERM_BATCTRL the battery ID resistor is combined
- * with a NTC resistor to both identify the battery and to measure its
- * temperature. Different phone manufactures uses different techniques to both
- * identify the battery and to read its temperature.
- */
-enum abx500_adc_therm {
- ABx500_ADC_THERM_BATCTRL,
- ABx500_ADC_THERM_BATTEMP,
-};
-
-/**
- * struct abx500_res_to_temp - defines one point in a temp to res curve. To
- * be used in battery packs that combines the identification resistor with a
- * NTC resistor.
- * @temp: battery pack temperature in Celsius
- * @resist: NTC resistor net total resistance
- */
-struct abx500_res_to_temp {
- int temp;
- int resist;
-};
-
-/**
- * struct abx500_v_to_cap - Table for translating voltage to capacity
- * @voltage: Voltage in mV
- * @capacity: Capacity in percent
- */
-struct abx500_v_to_cap {
- int voltage;
- int capacity;
-};
-
-/* Forward declaration */
-struct abx500_fg;
-
-/**
- * struct abx500_fg_parameters - Fuel gauge algorithm parameters, in seconds
- * if not specified
- * @recovery_sleep_timer: Time between measurements while recovering
- * @recovery_total_time: Total recovery time
- * @init_timer: Measurement interval during startup
- * @init_discard_time: Time we discard voltage measurement at startup
- * @init_total_time: Total init time during startup
- * @high_curr_time: Time current has to be high to go to recovery
- * @accu_charging: FG accumulation time while charging
- * @accu_high_curr: FG accumulation time in high current mode
- * @high_curr_threshold: High current threshold, in mA
- * @lowbat_threshold: Low battery threshold, in mV
- * @overbat_threshold: Over battery threshold, in mV
- * @battok_falling_th_sel0 Threshold in mV for battOk signal sel0
- * Resolution in 50 mV step.
- * @battok_raising_th_sel1 Threshold in mV for battOk signal sel1
- * Resolution in 50 mV step.
- * @user_cap_limit Capacity reported from user must be within this
- * limit to be considered as sane, in percentage
- * points.
- * @maint_thres This is the threshold where we stop reporting
- * battery full while in maintenance, in per cent
- * @pcut_enable: Enable power cut feature in ab8505
- * @pcut_max_time: Max time threshold
- * @pcut_flag_time: Flagtime threshold
- * @pcut_max_restart: Max number of restarts
- * @pcut_debounce_time: Sets battery debounce time
- */
-struct abx500_fg_parameters {
- int recovery_sleep_timer;
- int recovery_total_time;
- int init_timer;
- int init_discard_time;
- int init_total_time;
- int high_curr_time;
- int accu_charging;
- int accu_high_curr;
- int high_curr_threshold;
- int lowbat_threshold;
- int overbat_threshold;
- int battok_falling_th_sel0;
- int battok_raising_th_sel1;
- int user_cap_limit;
- int maint_thres;
- bool pcut_enable;
- u8 pcut_max_time;
- u8 pcut_flag_time;
- u8 pcut_max_restart;
- u8 pcut_debounce_time;
-};
-
-/**
- * struct abx500_charger_maximization - struct used by the board config.
- * @use_maxi: Enable maximization for this battery type
- * @maxi_chg_curr: Maximum charger current allowed
- * @maxi_wait_cycles: cycles to wait before setting charger current
- * @charger_curr_step delta between two charger current settings (mA)
- */
-struct abx500_maxim_parameters {
- bool ena_maxi;
- int chg_curr;
- int wait_cycles;
- int charger_curr_step;
-};
-
-/**
- * struct abx500_battery_type - different batteries supported
- * @name: battery technology
- * @resis_high: battery upper resistance limit
- * @resis_low: battery lower resistance limit
- * @charge_full_design: Maximum battery capacity in mAh
- * @nominal_voltage: Nominal voltage of the battery in mV
- * @termination_vol: max voltage upto which battery can be charged
- * @termination_curr battery charging termination current in mA
- * @recharge_cap battery capacity limit that will trigger a new
- * full charging cycle in the case where maintenan-
- * -ce charging has been disabled
- * @normal_cur_lvl: charger current in normal state in mA
- * @normal_vol_lvl: charger voltage in normal state in mV
- * @maint_a_cur_lvl: charger current in maintenance A state in mA
- * @maint_a_vol_lvl: charger voltage in maintenance A state in mV
- * @maint_a_chg_timer_h: charge time in maintenance A state
- * @maint_b_cur_lvl: charger current in maintenance B state in mA
- * @maint_b_vol_lvl: charger voltage in maintenance B state in mV
- * @maint_b_chg_timer_h: charge time in maintenance B state
- * @low_high_cur_lvl: charger current in temp low/high state in mA
- * @low_high_vol_lvl: charger voltage in temp low/high state in mV'
- * @battery_resistance: battery inner resistance in mOhm.
- * @n_r_t_tbl_elements: number of elements in r_to_t_tbl
- * @r_to_t_tbl: table containing resistance to temp points
- * @n_v_cap_tbl_elements: number of elements in v_to_cap_tbl
- * @v_to_cap_tbl: Voltage to capacity (in %) table
- * @n_batres_tbl_elements number of elements in the batres_tbl
- * @batres_tbl battery internal resistance vs temperature table
- */
-struct abx500_battery_type {
- int name;
- int resis_high;
- int resis_low;
- int charge_full_design;
- int nominal_voltage;
- int termination_vol;
- int termination_curr;
- int recharge_cap;
- int normal_cur_lvl;
- int normal_vol_lvl;
- int maint_a_cur_lvl;
- int maint_a_vol_lvl;
- int maint_a_chg_timer_h;
- int maint_b_cur_lvl;
- int maint_b_vol_lvl;
- int maint_b_chg_timer_h;
- int low_high_cur_lvl;
- int low_high_vol_lvl;
- int battery_resistance;
- int n_temp_tbl_elements;
- const struct abx500_res_to_temp *r_to_t_tbl;
- int n_v_cap_tbl_elements;
- const struct abx500_v_to_cap *v_to_cap_tbl;
- int n_batres_tbl_elements;
- const struct batres_vs_temp *batres_tbl;
-};
-
-/**
- * struct abx500_bm_capacity_levels - abx500 capacity level data
- * @critical: critical capacity level in percent
- * @low: low capacity level in percent
- * @normal: normal capacity level in percent
- * @high: high capacity level in percent
- * @full: full capacity level in percent
- */
-struct abx500_bm_capacity_levels {
- int critical;
- int low;
- int normal;
- int high;
- int full;
-};
-
-/**
- * struct abx500_bm_charger_parameters - Charger specific parameters
- * @usb_volt_max: maximum allowed USB charger voltage in mV
- * @usb_curr_max: maximum allowed USB charger current in mA
- * @ac_volt_max: maximum allowed AC charger voltage in mV
- * @ac_curr_max: maximum allowed AC charger current in mA
- */
-struct abx500_bm_charger_parameters {
- int usb_volt_max;
- int usb_curr_max;
- int ac_volt_max;
- int ac_curr_max;
-};
-
-/**
- * struct abx500_bm_data - abx500 battery management data
- * @temp_under under this temp, charging is stopped
- * @temp_low between this temp and temp_under charging is reduced
- * @temp_high between this temp and temp_over charging is reduced
- * @temp_over over this temp, charging is stopped
- * @temp_now present battery temperature
- * @temp_interval_chg temperature measurement interval in s when charging
- * @temp_interval_nochg temperature measurement interval in s when not charging
- * @main_safety_tmr_h safety timer for main charger
- * @usb_safety_tmr_h safety timer for usb charger
- * @bkup_bat_v voltage which we charge the backup battery with
- * @bkup_bat_i current which we charge the backup battery with
- * @no_maintenance indicates that maintenance charging is disabled
- * @capacity_scaling indicates whether capacity scaling is to be used
- * @abx500_adc_therm placement of thermistor, batctrl or battemp adc
- * @chg_unknown_bat flag to enable charging of unknown batteries
- * @enable_overshoot flag to enable VBAT overshoot control
- * @auto_trig flag to enable auto adc trigger
- * @fg_res resistance of FG resistor in 0.1mOhm
- * @n_btypes number of elements in array bat_type
- * @batt_id index of the identified battery in array bat_type
- * @interval_charging charge alg cycle period time when charging (sec)
- * @interval_not_charging charge alg cycle period time when not charging (sec)
- * @temp_hysteresis temperature hysteresis
- * @gnd_lift_resistance Battery ground to phone ground resistance (mOhm)
- * @n_chg_out_curr number of elements in array chg_output_curr
- * @n_chg_in_curr number of elements in array chg_input_curr
- * @chg_output_curr charger output current level map
- * @chg_input_curr charger input current level map
- * @maxi maximization parameters
- * @cap_levels capacity in percent for the different capacity levels
- * @bat_type table of supported battery types
- * @chg_params charger parameters
- * @fg_params fuel gauge parameters
- */
-struct abx500_bm_data {
- int temp_under;
- int temp_low;
- int temp_high;
- int temp_over;
- int temp_now;
- int temp_interval_chg;
- int temp_interval_nochg;
- int main_safety_tmr_h;
- int usb_safety_tmr_h;
- int bkup_bat_v;
- int bkup_bat_i;
- bool autopower_cfg;
- bool ac_enabled;
- bool usb_enabled;
- bool no_maintenance;
- bool capacity_scaling;
- bool chg_unknown_bat;
- bool enable_overshoot;
- bool auto_trig;
- enum abx500_adc_therm adc_therm;
- int fg_res;
- int n_btypes;
- int batt_id;
- int interval_charging;
- int interval_not_charging;
- int temp_hysteresis;
- int gnd_lift_resistance;
- int n_chg_out_curr;
- int n_chg_in_curr;
- int *chg_output_curr;
- int *chg_input_curr;
- const struct abx500_maxim_parameters *maxi;
- const struct abx500_bm_capacity_levels *cap_levels;
- struct abx500_battery_type *bat_type;
- const struct abx500_bm_charger_parameters *chg_params;
- const struct abx500_fg_parameters *fg_params;
-};
-
-enum {
- NTC_EXTERNAL = 0,
- NTC_INTERNAL,
-};
-
-int ab8500_bm_of_probe(struct device *dev,
- struct device_node *np,
- struct abx500_bm_data *bm);
-
int abx500_set_register_interruptible(struct device *dev, u8 bank, u8 reg,
u8 value);
int abx500_get_register_interruptible(struct device *dev, u8 bank, u8 reg,
OSDN Git Service
