OSDN Git Service
Michael Walle [Wed, 11 Dec 2019 19:57:30 +0000 (20:57 +0100)]
spi: nxp-fspi: Ensure width is respected in spi-mem operations
Make use of a core helper to ensure the desired width is respected
when calling spi-mem operators.
Otherwise only the SPI controller will be matched with the flash chip,
which might lead to wrong widths. Also consider the width specified by
the user in the device tree.
Fixes:
a5356aef6a90 ("spi: spi-mem: Add driver for NXP FlexSPI controller")
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20191211195730.26794-1-michael@walle.cc
Signed-off-by: Mark Brown <broonie@kernel.org>
Vignesh Raghavendra [Wed, 11 Dec 2019 15:52:16 +0000 (21:22 +0530)]
spi: spi-ti-qspi: Fix a bug when accessing non default CS
When switching ChipSelect from default CS0 to any other CS, driver fails
to update the bits in system control module register that control which
CS is mapped for MMIO access. This causes reads to fail when driver
tries to access QSPI flash on CS1/2/3.
Fix this by updating appropriate bits whenever active CS changes.
Reported-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20191211155216.30212-1-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Christophe Leroy [Mon, 9 Dec 2019 15:27:27 +0000 (15:27 +0000)]
spi: fsl: don't map irq during probe
With lastest kernel, the following warning is observed at startup:
[ 1.500609] ------------[ cut here ]------------
[ 1.505225] remove_proc_entry: removing non-empty directory 'irq/22', leaking at least 'fsl_spi'
[ 1.514234] WARNING: CPU: 0 PID: 1 at fs/proc/generic.c:682 remove_proc_entry+0x198/0x1c0
[ 1.522403] CPU: 0 PID: 1 Comm: swapper Not tainted
5.4.0-s3k-dev-02248-g93532430a4ff #2564
[ 1.530724] NIP:
c0197694 LR:
c0197694 CTR:
c0050d80
[ 1.535762] REGS:
df4a5af0 TRAP: 0700 Not tainted (
5.4.0-02248-g93532430a4ff)
[ 1.543818] MSR:
00029032 <EE,ME,IR,DR,RI> CR:
22028222 XER:
00000000
[ 1.550524]
[ 1.550524] GPR00:
c0197694 df4a5ba8 df4a0000 00000054 00000000 00000000 00004a38 00000010
[ 1.550524] GPR08:
c07c5a30 00000800 00000000 00001032 22000208 00000000 c0004b14 00000000
[ 1.550524] GPR16:
00000000 00000000 00000000 00000000 00000000 00000000 c0830000 c07fc078
[ 1.550524] GPR24:
c08e8ca0 df665d10 df60ea98 c07c9db8 00000001 df5d5ae3 df5d5a80 df43f8e3
[ 1.585327] NIP [
c0197694] remove_proc_entry+0x198/0x1c0
[ 1.590628] LR [
c0197694] remove_proc_entry+0x198/0x1c0
[ 1.595829] Call Trace:
[ 1.598280] [
df4a5ba8] [
c0197694] remove_proc_entry+0x198/0x1c0 (unreliable)
[ 1.605321] [
df4a5bd8] [
c0067acc] unregister_irq_proc+0x5c/0x70
[ 1.611238] [
df4a5bf8] [
c005fbc4] free_desc+0x3c/0x80
[ 1.616286] [
df4a5c18] [
c005fe2c] irq_free_descs+0x70/0xa8
[ 1.621778] [
df4a5c38] [
c033d3fc] of_fsl_spi_probe+0xdc/0x3cc
[ 1.627525] [
df4a5c88] [
c02f0f64] platform_drv_probe+0x44/0xa4
[ 1.633350] [
df4a5c98] [
c02eee44] really_probe+0x1ac/0x418
[ 1.638829] [
df4a5cc8] [
c02ed3e8] bus_for_each_drv+0x64/0xb0
[ 1.644481] [
df4a5cf8] [
c02ef950] __device_attach+0xd4/0x128
[ 1.650132] [
df4a5d28] [
c02ed61c] bus_probe_device+0xa0/0xbc
[ 1.655783] [
df4a5d48] [
c02ebbe8] device_add+0x544/0x74c
[ 1.661096] [
df4a5d88] [
c0382b78] of_platform_device_create_pdata+0xa4/0x100
[ 1.668131] [
df4a5da8] [
c0382cf4] of_platform_bus_create+0x120/0x20c
[ 1.674474] [
df4a5df8] [
c0382d50] of_platform_bus_create+0x17c/0x20c
[ 1.680818] [
df4a5e48] [
c0382e88] of_platform_bus_probe+0x9c/0xf0
[ 1.686907] [
df4a5e68] [
c0751404] __machine_initcall_cmpcpro_cmpcpro_declare_of_platform_devices+0x74/0x1a4
[ 1.696629] [
df4a5e98] [
c072a4cc] do_one_initcall+0x8c/0x1d4
[ 1.702282] [
df4a5ef8] [
c072a768] kernel_init_freeable+0x154/0x204
[ 1.708455] [
df4a5f28] [
c0004b2c] kernel_init+0x18/0x110
[ 1.713769] [
df4a5f38] [
c00122ac] ret_from_kernel_thread+0x14/0x1c
[ 1.719926] Instruction dump:
[ 1.722889]
2c030000 4182004c 3863ffb0 3c80c05f 80e3005c 388436a0 3c60c06d 7fa6eb78
[ 1.730630]
7fe5fb78 38840280 38634178 4be8c611 <
0fe00000>
4bffff6c 3c60c071 7fe4fb78
[ 1.738556] ---[ end trace
05d0720bf2e352e2 ]---
The problem comes from the error path which calls
irq_dispose_mapping() while the IRQ has been requested with
devm_request_irq().
IRQ doesn't need to be mapped with irq_of_parse_and_map(). The only
need is to get the IRQ virtual number. For that, use
of_irq_to_resource() instead of the
irq_of_parse_and_map()/irq_dispose_mapping() pair.
Fixes:
500a32abaf81 ("spi: fsl: Call irq_dispose_mapping in err path")
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Link: https://lore.kernel.org/r/518cfb83347d5372748e7fe72f94e2e9443d0d4a.1575905123.git.christophe.leroy@c-s.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
Chuhong Yuan [Fri, 6 Dec 2019 07:55:00 +0000 (15:55 +0800)]
spi: spi-cavium-thunderx: Add missing pci_release_regions()
The driver forgets to call pci_release_regions() in probe failure
and remove.
Add the missed calls to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20191206075500.18525-1-hslester96@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Huanpeng Xin [Wed, 4 Dec 2019 07:13:59 +0000 (15:13 +0800)]
spi: sprd: Fix the incorrect SPI register
The original code used an incorrect SPI register to initialize the SPI
controller in sprd_spi_init_hw(), thus fix it.
Fixes:
e7d973a31c24 ("spi: sprd: Add SPI driver for Spreadtrum SC9860")
Signed-off-by: Huanpeng Xin <huanpeng.xin@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/b4f7f89ec0fdc595335687bfbd9f962213bc4a1d.1575443510.git.baolin.wang7@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
YueHaibing [Sat, 30 Nov 2019 01:28:28 +0000 (09:28 +0800)]
gpiolib: of: Make of_gpio_spi_cs_get_count static
Fix sparse warning:
drivers/gpio/gpiolib-of.c:35:5: warning:
symbol 'of_gpio_spi_cs_get_count' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191130012828.14504-1-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Linus Walleij [Thu, 28 Nov 2019 08:37:18 +0000 (09:37 +0100)]
spi: fsl: Handle the single hardwired chipselect case
The Freescale MPC8xxx had a special quirk for handling a
single hardwired chipselect, the case when we're using neither
GPIO nor native chip select: when inspecting the device tree
and finding zero "cs-gpios" on the device node the code would
assume we have a single hardwired chipselect that leaves the
device always selected.
This quirk is not handled by the new core code, so we need
to check the "cs-gpios" explicitly in the driver and set
pdata->max_chipselect = 1 which will later fall through to
the SPI master ->num_chipselect.
Make sure not to assign the chip select handler in this
case: there is no handling needed since the chip is always
selected, and this is what the old code did as well.
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Reported-by: Christophe Leroy <christophe.leroy@c-s.fr>
Fixes:
0f0581b24bd0 ("spi: fsl: Convert to use CS GPIO descriptors")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Christophe Leroy <christophe.leroy@c-s.fr> (No tested the
Link: https://lore.kernel.org/r/20191128083718.39177-3-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Linus Walleij [Thu, 28 Nov 2019 08:37:17 +0000 (09:37 +0100)]
gpio: Handle counting of Freescale chipselects
We have a special quirk to handle the Freescale
nonstandard SPI chipselect GPIOs in the gpiolib-of.c
file, but it currently only handles the case where
the GPIOs are actually requested (gpiod_*get()).
We also need to handle that the SPI core attempts
to count the GPIOs before use, and that needs a
similar quirk in the OF part of the library.
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Reported-by: Christophe Leroy <christophe.leroy@c-s.fr>
Fixes:
0f0581b24bd0 ("spi: fsl: Convert to use CS GPIO descriptors")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Christophe Leroy <christophe.leroy@c-s.fr>
Link: https://lore.kernel.org/r/20191128083718.39177-2-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Linus Walleij [Thu, 28 Nov 2019 08:37:16 +0000 (09:37 +0100)]
spi: fsl: Fix GPIO descriptor support
This makes the driver actually support looking up GPIO
descriptor. A coding mistake in the initial descriptor
support patch was that it was failing to turn on the very
feature it was implementing. Mea culpa.
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Reported-by: Christophe Leroy <christophe.leroy@c-s.fr>
Fixes:
0f0581b24bd0 ("spi: fsl: Convert to use CS GPIO descriptors")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Christophe Leroy <christophe.leroy@c-s.fr>
Link: https://lore.kernel.org/r/20191128083718.39177-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Charles Keepax [Wed, 27 Nov 2019 15:39:36 +0000 (15:39 +0000)]
spi: dw: Correct handling of native chipselect
This patch reverts commit
6e0a32d6f376 ("spi: dw: Fix default polarity
of native chipselect").
The SPI framework always called the set_cs callback with the logic
level it desired on the chip select line, which is what the drivers
original handling supported. commit
f3186dd87669 ("spi: Optionally
use GPIO descriptors for CS GPIOs") changed these symantics, but only
in the case of drivers that also support GPIO chip selects, to true
meaning apply slave select rather than logic high. This left things in
an odd state where a driver that only supports hardware chip selects,
the core would handle polarity but if the driver supported GPIOs as
well the driver should handle polarity. At this point the reverted
change was applied to change the logic in the driver to match new
system.
This was then broken by commit
3e5ec1db8bfe ("spi: Fix SPI_CS_HIGH
setting when using native and GPIO CS") which reverted the core back
to consistently calling set_cs with a logic level.
This fix reverts the driver code back to its original state to match
the current core code. This is probably a better fix as a) the set_cs
callback is always called with consistent symantics and b) the
inversion for SPI_CS_HIGH can be handled in the core and doesn't need
to be coded in each driver supporting it.
Fixes:
3e5ec1db8bfe ("spi: Fix SPI_CS_HIGH setting when using native and GPIO CS")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191127153936.29719-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Charles Keepax [Tue, 26 Nov 2019 16:41:40 +0000 (16:41 +0000)]
spi: cadence: Correct handling of native chipselect
To fix a regression on the Cadence SPI driver, this patch reverts
commit
6046f5407ff0 ("spi: cadence: Fix default polarity of native
chipselect").
This patch was not the correct fix for the issue. The SPI framework
calls the set_cs line with the logic level it desires on the chip select
line, as such the old is_high handling was correct. However, this was
broken by the fact that before commit
3e5ec1db8bfe ("spi: Fix SPI_CS_HIGH
setting when using native and GPIO CS") all controllers that offered
the use of a GPIO chip select had SPI_CS_HIGH applied, even for hardware
chip selects. This caused the value passed into the driver to be inverted.
Which unfortunately makes it look like a logical enable the chip select
value.
Since the core was corrected to not unconditionally apply SPI_CS_HIGH,
the Cadence driver, whilst using the hardware chip select, will deselect
the chip select every time we attempt to communicate with the device,
which results in failed communications.
Fixes:
3e5ec1db8bfe ("spi: Fix SPI_CS_HIGH setting when using native and GPIO CS")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191126164140.6240-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Jarkko Nikula [Mon, 25 Nov 2019 12:51:59 +0000 (14:51 +0200)]
spi: pxa2xx: Add support for Intel Jasper Lake
LPSS SPI on Intel Jasper Lake is compatible with Intel Ice Lake which
follows Intel Cannon Lake. Add PCI IDs of Jasper Lake.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20191125125159.15404-1-jarkko.nikula@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Benjamin Gaignard [Wed, 20 Nov 2019 19:44:44 +0000 (20:44 +0100)]
dt-bindings: spi: Convert stm32 QSPI bindings to json-schema
Convert the STM32 QSPI binding to DT schema format using json-schema
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20191120194444.10540-1-benjamin.gaignard@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Peter Ujfalusi [Thu, 21 Nov 2019 09:27:03 +0000 (11:27 +0200)]
spi: pic32: Retire dma_request_slave_channel_compat()
There is no reason to use the dma_request_slave_channel_compat() as no
filter function and parameter is provided.
Switch the driver to use dma_request_chan() instead and add support for
deferred probing against DMA channel.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20191121092703.30465-1-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Krzysztof Kozlowski [Wed, 20 Nov 2019 13:39:16 +0000 (21:39 +0800)]
spi: Fix Kconfig indentation
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20191120133916.13595-1-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Luhua Xu [Mon, 18 Nov 2019 04:57:16 +0000 (12:57 +0800)]
spi: mediatek: add SPI_CS_HIGH support
Change to use SPI_CS_HIGH to support spi CS polarity setting
for chips support enhance_timing.
Signed-off-by: Luhua Xu <luhua.xu@mediatek.com>
Link: https://lore.kernel.org/r/1574053037-26721-2-git-send-email-luhua.xu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Chuhong Yuan [Mon, 18 Nov 2019 02:48:48 +0000 (10:48 +0800)]
spi: st-ssc4: add missed pm_runtime_disable
The driver forgets to call pm_runtime_disable in probe failure
and remove.
Add the missed calls to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20191118024848.21645-1-hslester96@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Chuhong Yuan [Fri, 15 Nov 2019 08:31:22 +0000 (16:31 +0800)]
spi: tegra20-slink: add missed clk_unprepare
The driver misses calling clk_unprepare in probe failure and remove.
Add the calls to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20191115083122.12278-1-hslester96@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Peter Ujfalusi [Wed, 13 Nov 2019 09:42:56 +0000 (11:42 +0200)]
spi: tegra20-slink: Use dma_request_chan() directly for channel request
dma_request_slave_channel_reason() is:
#define dma_request_slave_channel_reason(dev, name) \
dma_request_chan(dev, name)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20191113094256.1108-10-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Peter Ujfalusi [Wed, 13 Nov 2019 09:42:55 +0000 (11:42 +0200)]
spi: tegra114: Use dma_request_chan() directly for channel request
dma_request_slave_channel_reason() is:
#define dma_request_slave_channel_reason(dev, name) \
dma_request_chan(dev, name)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20191113094256.1108-9-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Peter Ujfalusi [Wed, 13 Nov 2019 09:42:54 +0000 (11:42 +0200)]
spi: s3c64xx: Use dma_request_chan() directly for channel request
dma_request_slave_channel_reason() is:
#define dma_request_slave_channel_reason(dev, name) \
dma_request_chan(dev, name)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Andi Shyti <andi@etezian.org>
Link: https://lore.kernel.org/r/20191113094256.1108-8-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Peter Ujfalusi [Wed, 13 Nov 2019 09:42:53 +0000 (11:42 +0200)]
spi: qup: Use dma_request_chan() directly for channel request
dma_request_slave_channel_reason() is:
#define dma_request_slave_channel_reason(dev, name) \
dma_request_chan(dev, name)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191113094256.1108-7-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Peter Ujfalusi [Wed, 13 Nov 2019 09:42:52 +0000 (11:42 +0200)]
spi: pl022: Use dma_request_chan() directly for channel request
dma_request_slave_channel_reason() is:
#define dma_request_slave_channel_reason(dev, name) \
dma_request_chan(dev, name)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191113094256.1108-6-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Peter Ujfalusi [Wed, 13 Nov 2019 09:42:51 +0000 (11:42 +0200)]
spi: imx: Use dma_request_chan() directly for channel request
dma_request_slave_channel_reason() is:
#define dma_request_slave_channel_reason(dev, name) \
dma_request_chan(dev, name)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191113094256.1108-5-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Peter Ujfalusi [Wed, 13 Nov 2019 09:42:50 +0000 (11:42 +0200)]
spi: fsl-lpspi: Use dma_request_chan() directly for channel request
dma_request_slave_channel_reason() is:
#define dma_request_slave_channel_reason(dev, name) \
dma_request_chan(dev, name)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191113094256.1108-4-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Peter Ujfalusi [Wed, 13 Nov 2019 09:42:49 +0000 (11:42 +0200)]
spi: atmel: Use dma_request_chan() directly for channel request
dma_request_slave_channel_reason() is:
#define dma_request_slave_channel_reason(dev, name) \
dma_request_chan(dev, name)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20191113094256.1108-3-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Peter Ujfalusi [Wed, 13 Nov 2019 09:42:48 +0000 (11:42 +0200)]
spi: at91-usart: Use dma_request_chan() directly for channel request
dma_request_slave_channel_reason() is:
#define dma_request_slave_channel_reason(dev, name) \
dma_request_chan(dev, name)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20191113094256.1108-2-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Tony Lindgren [Mon, 11 Nov 2019 19:53:34 +0000 (11:53 -0800)]
spi: Fix regression to return zero on success instead of positive value
Commit
d948e6ca1899 ("spi: add power control when set_cs") added generic
runtime PM handling, but also changed the return value to be 1 instead
of 0 that we had earlier as pm_runtime_get functions return a positve
value on success.
This causes SPI devices to return errors for cases where they do:
ret = spi_setup(spi);
if (ret)
return ret;
As in many cases the SPI devices do not check for if (ret < 0).
Let's fix this by setting the status to 0 on succeess after the
runtime PM calls. Let's not return 0 at the end of the function
as this might break again later on if the function changes and
starts returning status again.
Fixes:
d948e6ca1899 ("spi: add power control when set_cs")
Cc: Luhua Xu <luhua.xu@mediatek.com>
Cc: wsd_upstream@mediatek.com
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20191111195334.44833-1-tony@atomide.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Chuhong Yuan [Sat, 9 Nov 2019 08:09:43 +0000 (16:09 +0800)]
spi: pxa2xx: Add missed security checks
pxa2xx_spi_init_pdata misses checks for devm_clk_get and
platform_get_irq.
Add checks for them to fix the bugs.
Since ssp->clk and ssp->irq are used in probe, they are mandatory here.
So we cannot use _optional() for devm_clk_get and platform_get_irq.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20191109080943.30428-1-hslester96@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Chuhong Yuan [Sat, 9 Nov 2019 07:55:17 +0000 (15:55 +0800)]
spi: nxp-fspi: Use devm API to fix missed unregistration of controller
This driver forgets to unregister controller when remove.
Use devm API to unregister it automatically to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Link: https://lore.kernel.org/r/20191109075517.29988-1-hslester96@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Vignesh Raghavendra [Sat, 9 Nov 2019 04:18:27 +0000 (09:48 +0530)]
spi: omap2-mcspi: Remove redundant checks
Both omap2_mcspi_tx_dma() and omap2_mcspi_rx_dma() are only called from
omap2_mcspi_txrx_dma() and omap2_mcspi_txrx_dma() is always called after
making sure that mcspi_dma->dma_rx and mcspi_dma->dma_tx are not NULL
(see omap2_mcspi_transfer_one()).
Therefore remove redundant NULL checks for omap2_mcspi->dma_tx and
omap2_mcspi->dma_rx pointers in omap2_mcspi_tx_dma() and
omap2_mcspi_rx_dma() respectively.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20191109041827.26934-1-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Miquel Raynal [Fri, 8 Nov 2019 14:07:44 +0000 (15:07 +0100)]
spi: zynq-qspi: Support two chip selects
The Zynq QSPI controller features 2 CS. When the num-cs DT property
is set to 2, the hardware will be initialized to support having two
devices connected over each CS.
In this case, both CS lines are driven by the state of the U_PAGE
(upper page) bit. When unset, the lower page (CS0) is selected,
otherwise it is the upper page (CS1).
Change tested on a custom design featuring two SPI-NORs with different
CS on the Zynq-7000 QSPI bus.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191108140744.1734-8-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Miquel Raynal [Fri, 8 Nov 2019 14:07:43 +0000 (15:07 +0100)]
spi: zynq-qspi: Do the actual hardware initialization later in the probe
Supporting more than one CS will need some tweaking of the linear
configuration register which is (rightfully) initialized in the
hardware initialization helper. The extra initialization needs the
knowledge of the actual number of CS, which is retrieved by reading
the value of the num-cs DT property.
As the initialization helper is called pretty early and might be
called much later in the probe without side effect, let's delay it a
bit so that the number of CS will be available when running this
helper. This way, adding support for multiple CS lines in a next patch
will be eased.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191108140744.1734-7-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Miquel Raynal [Fri, 8 Nov 2019 14:07:42 +0000 (15:07 +0100)]
spi: zynq-qspi: Clarify the select chip function
The code used to assert and de-assert a chip select line is very
complicated for no reason. Simplify the logic by either setting or
resetting the concerned bit, which actually only changes an electrical
state.
Update the comment to reflect that there is no possibility to actually
choose a CS as the default (CS0) will be driven in any case.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191108140744.1734-6-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Miquel Raynal [Fri, 8 Nov 2019 14:07:41 +0000 (15:07 +0100)]
spi: zynq-qspi: Enhance the Linear CFG bit definitions
Using masks makes sense when manipulating fields of several bits. When
only one bit is involved, it is usual to just use the BIT() macro but
in this case using the term mask is abusive. Fix the #define macros
and their comments.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191108140744.1734-5-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Miquel Raynal [Fri, 8 Nov 2019 14:07:40 +0000 (15:07 +0100)]
spi: zynq-qspi: Keep the bitfields naming consistent
Most of the bits/bitfields #define'd in this driver are composed with:
1/ the driver prefix
2/ the name of the register they apply to
Keep the naming consistent by applying this rule to the CONFIG register
internals. These definitions will be used in a following change set.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191108140744.1734-4-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Miquel Raynal [Fri, 8 Nov 2019 14:07:38 +0000 (15:07 +0100)]
spi: zynq-qspi: Anything else than CS0 is not supported yet
Unlike what the driver is currently advertizing, CS0 only can be used,
CS1 is not supported at all. Prevent people to use CS1.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191108140744.1734-2-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Miquel Raynal [Fri, 8 Nov 2019 10:59:15 +0000 (11:59 +0100)]
spi: zynq-qspi: Keep the naming consistent across the driver
In this driver (and also in a lot of other drivers in drivers/spi/),
the spi_controller structure is sometimes referred as 'ctlr' and
sometimes as 'ctrl'. Grepping there shows that 'ctlr' seems to be more
common so keep the naming consistent in this driver and s/ctrl/ctlr/.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191108105920.19014-3-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Chris Packham [Thu, 7 Nov 2019 04:42:35 +0000 (17:42 +1300)]
spi: spi-mem: fallback to using transfers when CS gpios are used
Devices with chip selects driven via GPIO are not compatible with the
spi-mem operations. Fallback to using standard spi transfers when the
device is connected with a gpio CS.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20191107044235.4864-3-chris.packham@alliedtelesis.co.nz
Signed-off-by: Mark Brown <broonie@kernel.org>
Chris Packham [Thu, 7 Nov 2019 04:42:34 +0000 (17:42 +1300)]
spi: bcm-qspi: Convert to use CS GPIO descriptors
Set use_gpio_descriptors to true and avoid asserting the native chip
select if the spi core has done it for us.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/r/20191107044235.4864-2-chris.packham@alliedtelesis.co.nz
Signed-off-by: Mark Brown <broonie@kernel.org>
Pan Bian [Wed, 6 Nov 2019 02:36:09 +0000 (10:36 +0800)]
spi: img-spfi: fix potential double release
The channels spfi->tx_ch and spfi->rx_ch are not set to NULL after they
are released. As a result, they will be released again, either on the
error handling branch in the same function or in the corresponding
remove function, i.e. img_spfi_remove(). This patch fixes the bug by
setting the two members to NULL.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Link: https://lore.kernel.org/r/1573007769-20131-1-git-send-email-bianpan2016@163.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Luhua Xu [Wed, 30 Oct 2019 09:03:54 +0000 (17:03 +0800)]
spi: add power control when set_cs
As to set_cs takes effect immediately, power spi
is needed when setup spi.
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Luhua Xu <luhua.xu@mediatek.com>
Link: https://lore.kernel.org/r/1572426234-30019-1-git-send-email-luhua.xu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Linus Walleij [Wed, 30 Oct 2019 07:36:24 +0000 (08:36 +0100)]
spi: zynq-qspi: Drop GPIO header
This driver does not use any symbols from the legacy GPIO
header so drop the include.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191030073624.23974-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Linus Walleij [Wed, 30 Oct 2019 07:34:18 +0000 (08:34 +0100)]
spi: dw: Drop GPIO header
The DW driver does not use the legacy GPIO header so drop
it from the spi-dw.h include.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191030073418.23717-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Linus Walleij [Wed, 30 Oct 2019 07:38:32 +0000 (08:38 +0100)]
spi: txx9: Convert to use GPIO descriptors
This converts the TXX9 SPI driver to use GPIO descriptors
to control the GPIO chip selects.
As the driver was clearly (ab)using the device tree "reg"
property to offset into the global GPIO chip we have to
add a hack to counter the hack: add a 1-to-1 chip select
to GPIO offset mapping for all 16 lines on the TXX9 GPIO
chip. The details are described in a largeish comment
in the patch.
We do not need to set up the GPIO as output any more since
the core will take care of this, as well as it will handle
the polarity inversion semantics.
Cc: Atsushi Nemoto <atsushi.nemoto@sord.co.jp>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20191030073832.24038-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Jarkko Nikula [Wed, 30 Oct 2019 11:31:37 +0000 (13:31 +0200)]
spi: dw: Remove runtime PM enable/disable from common part of the driver
Committed version of the commit
b9fc2d207e54 ("spi: dw: Move runtime PM
enable/disable from common to platform driver part") does not include by
some reason changes to drivers/spi/spi-dw.c that were part of the original
patch sent to the mailing list.
Complete the code move by doing those changes now.
Fixes:
b9fc2d207e54 ("spi: dw: Move runtime PM enable/disable from common to platform driver part")
Cc: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20191030113137.15459-1-jarkko.nikula@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Lingling Xu [Mon, 28 Oct 2019 10:10:31 +0000 (18:10 +0800)]
spi: sprd: adi: Set BIT_WDG_NEW bit when rebooting
When rebooting system, the PMIC watchdog time loading may not be loaded
correctly when another system is feeding the PMIC watchdog, since we did
not check the watchdog busy status before loading time values.
Thus we should set the BIT_WDG_NEW bit before loading time values, that
can support multiple loads without checking busy status to make sure the
time values can be loaded successfully to avoid this potential issue.
Signed-off-by: Lingling Xu <ling_ling.xu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Link: https://lore.kernel.org/r/5655318a7252c9ea518c2f7950a61228ab8f42bf.1572257085.git.baolin.wang@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Lingling Xu [Mon, 28 Oct 2019 10:10:30 +0000 (18:10 +0800)]
spi: sprd: adi: Add missing lock protection when rebooting
When rebooting the system, we should lock the watchdog after
configuration to make sure the watchdog can reboot the system
successfully.
Signed-off-by: Lingling Xu <ling_ling.xu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Link: https://lore.kernel.org/r/7b04711127434555e3a1a86bc6be99860cd86668.1572257085.git.baolin.wang@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Andy Shevchenko [Mon, 21 Oct 2019 10:36:24 +0000 (13:36 +0300)]
spi: pxa2xx: Introduce temporary variables to increase readability
The current conditional for PCI ID matching is hard to read.
Introduce couple of temporary variables to increase readability
of the code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20191021103625.4250-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Alvaro Gamez Machado [Thu, 24 Oct 2019 11:07:56 +0000 (13:07 +0200)]
spi: xilinx: Add DT support for selecting transfer word width
This core supports either 8, 16 or 32 bits as word width. This value is only
settable on instantiation, and thus we need to support any of them by means
of the device tree.
Signed-off-by: Alvaro Gamez Machado <alvaro.gamez@hazent.com>
Link: https://lore.kernel.org/r/20191024110757.25820-3-alvaro.gamez@hazent.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Alvaro Gamez Machado [Thu, 24 Oct 2019 11:07:55 +0000 (13:07 +0200)]
spi: xilinx: add description of new property xlnx,num-transfer-bits
This property is used to set the number of bits per transfer (bits_per_word).
Xilinx' IP core allows either 8, 16 or 32, and is non changeable on runtime,
only when instantiating the core.
Signed-off-by: Alvaro Gamez Machado <alvaro.gamez@hazent.com>
Link: https://lore.kernel.org/r/20191024110757.25820-2-alvaro.gamez@hazent.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Andy Shevchenko [Wed, 23 Oct 2019 12:16:43 +0000 (15:16 +0300)]
spi: Fix spelling in the comments
Two spelling mistakes are being fixed.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20191023121643.25237-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Alexandru Ardelean [Wed, 23 Oct 2019 07:00:46 +0000 (10:00 +0300)]
spi: document CS setup, hold & inactive times in header
This change documents the CS setup, host & inactive times. They were
omitted when the fields were added, and were caught by one of the build
bots.
Fixes:
25093bdeb6bc ("spi: implement SW control for CS times")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20191023070046.12478-1-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Jarkko Nikula [Fri, 18 Oct 2019 13:21:31 +0000 (16:21 +0300)]
spi: dw-pci: Fix Chip Select amount on Intel Elkhart Lake PSE SPI
Intel(R) Programmable Services Engine (Intel(R) PSE) SPI controllers in
Intel Elkhart Lake have two Chip Select signals instead of one.
Reported-by: Raymond Tan <raymond.tan@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20191018132131.31608-3-jarkko.nikula@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Raymond Tan [Fri, 18 Oct 2019 13:21:30 +0000 (16:21 +0300)]
spi: dw-pci: Add runtime power management support
Implement pm_runtime hooks at pci driver.
Signed-off-by: Raymond Tan <raymond.tan@intel.com>
[jarkko.nikula@linux.intel.com: Forward ported on top of
commit
1e6959832510 ("spi: dw: Add basic runtime PM support")]
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20191018132131.31608-2-jarkko.nikula@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Gregory CLEMENT [Thu, 17 Oct 2019 14:18:46 +0000 (16:18 +0200)]
spi: atmel: Improve CS0 case support on AT91RM9200
Thanks to the recent change in this driver, it is now possible to
prevent using the CS0 with GPIO during setup. It then allows to remove
the special handling of this case in the cs_activate() and
cs_deactivate() functions.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20191017141846.7523-8-gregory.clement@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Gregory CLEMENT [Thu, 17 Oct 2019 14:18:45 +0000 (16:18 +0200)]
spi: atmel: Improve and fix GPIO CS usage
In the previous implementation of this driver, the index of the GPIO
used as CS was linked to the offset of the CS register used to
configure the transfer.
With this new implementation the first CS register not used by
internal CS is associated to all the GPIO CS. It allows to not be
anymore limited to have only 4 CS managed, now it is possible to have
in the same time until 3 internal CS and no more limit for the CS
GPIO.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20191017141846.7523-7-gregory.clement@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Gregory CLEMENT [Thu, 17 Oct 2019 14:18:44 +0000 (16:18 +0200)]
spi: atmel: Remove platform data support
This driver is now only used through the device tree. Simplify code
by explicitly depend on device tree.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20191017141846.7523-6-gregory.clement@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Gregory CLEMENT [Thu, 17 Oct 2019 14:18:43 +0000 (16:18 +0200)]
spi: atmel: Remove useless private field
Since the conversion to GPIO descriptor, the GPIO used as chip select,
can be directly access from the spi_device struct. So there is no need
to keep the field npcs_pin.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20191017141846.7523-5-gregory.clement@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Gregory CLEMENT [Thu, 17 Oct 2019 14:18:42 +0000 (16:18 +0200)]
spi: atmel: Configure GPIO per CS instead of by controller
Instead of setting up the GPIO configuration for the whole controller,
do it at CS level. It will allow to mix internal CS and GPIO CS, which
is not possible with the current implementation.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20191017141846.7523-4-gregory.clement@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Gregory CLEMENT [Thu, 17 Oct 2019 14:18:41 +0000 (16:18 +0200)]
spi: atmel: Fix CS high support
Until a few years ago, this driver was only used with CS GPIO. The
only exception is CS0 on AT91RM9200 which has to use internal CS. A
limitation of the internal CS is that they don't support CS High.
So by using the CS GPIO the CS high configuration was available except
for the particular case CS0 on RM9200.
When the support for the internal chip-select was added, the check of
the CS high support was not updated. Due to this the driver accepts
this configuration for all the SPI controller v2 (used by all SoCs
excepting the AT91RM9200) whereas the hardware doesn't support it for
infernal CS.
This patch fixes the test to match the hardware capabilities.
Fixes:
4820303480a1 ("spi: atmel: add support for the internal chip-select of the spi controller")
Cc: <stable@vger.kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20191017141846.7523-3-gregory.clement@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Gregory CLEMENT [Thu, 17 Oct 2019 14:18:40 +0000 (16:18 +0200)]
spi: atmel: Remove and fix erroneous comments
Since CSAAT functionality support has been added. Some comments become
wrong. Fix them to match the current driver behavior.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20191017141846.7523-2-gregory.clement@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Andy Shevchenko [Fri, 18 Oct 2019 10:54:29 +0000 (13:54 +0300)]
spi: pxa2xx: Replace of_device.h with mod_devicetable.h and of.h
There is nothing in use from of_device.h. The definitions and macros
are available thru mod_devicetable.h and of.h.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20191018105429.82782-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Andy Shevchenko [Fri, 18 Oct 2019 10:54:28 +0000 (13:54 +0300)]
spi: pxa2xx: Convert to use device_get_match_data()
Convert to use device_get_match_data() instead of open coded variant.
While here, switch of_property_read_bool() to device_property_read_bool().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20191018105429.82782-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Andy Shevchenko [Fri, 18 Oct 2019 10:54:27 +0000 (13:54 +0300)]
spi: pxa2xx: Convert pxa2xx_spi_get_port_id() to take struct device
This is preparatory patch before converting to use device_get_match_data() API.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20191018105429.82782-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Andy Shevchenko [Fri, 18 Oct 2019 10:54:26 +0000 (13:54 +0300)]
spi: pxa2xx: Sort headers
Sort the headers in alphabetic order in order to ease the maintenance
for this part.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20191018105429.82782-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Andy Shevchenko [Fri, 18 Oct 2019 10:54:25 +0000 (13:54 +0300)]
spi: pxa2xx: No need to keep pointer to platform device
There is no need to keep a pointer to the platform device. Currently there are
no users of it directly, and if there will be in the future we may restore it
from pointer to the struct device.
Convert all users at the same time.
Cc: Russell King <linux@armlinux.org.uk>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20191018105429.82782-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Alexandru Ardelean [Thu, 26 Sep 2019 10:51:37 +0000 (13:51 +0300)]
spi: use new `spi_transfer_delay_exec` helper where straightforward
For many places in the spi drivers, using the new `spi_transfer_delay`
helper is straightforward.
It's just replacing:
```
if (t->delay_usecs)
udelay(t->delay_usecs);
```
with `spi_transfer_delay(t)` which handles both `delay_usecs` and the new
`delay` field.
This change replaces in all places (in the spi drivers) where this change
is simple.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-10-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Alexandru Ardelean [Thu, 26 Sep 2019 10:51:47 +0000 (13:51 +0300)]
spi: spi-axi: extend support for the `delay` field
The AXI SPI engine driver uses the `delay_usecs` field from `spi_transfer`
to configure delays, which the controller will execute.
This change extends the logic to also include the `delay` value, in case it
is used (instead if `delay_usecs`).
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-20-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Alexandru Ardelean [Thu, 26 Sep 2019 10:51:46 +0000 (13:51 +0300)]
spi: bcm63xx: extend error condition to `delay` as well
The driver errors out if `delay_usecs` is non-zero. This error condition
should be extended to the new `delay` field, to account for when it will be
used.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-19-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Alexandru Ardelean [Thu, 26 Sep 2019 10:51:45 +0000 (13:51 +0300)]
spi: spi-falcon: extend warning to `delay` as well
The WARN_ON macro prints a warning in syslog if `delay_usecs` is non-zero.
However, with the new intermediate `delay`, the warning should also be
printed.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-18-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Alexandru Ardelean [Thu, 26 Sep 2019 10:51:44 +0000 (13:51 +0300)]
spi: spi-fsl-espi: convert transfer delay to `spi_delay` format
The way the max delay is computed for this controller, it looks like it is
searching for the max delay from an SPI message a using that.
No idea if this is valid. But this change should support both `delay_usecs`
and the new `delay` data which is of `spi_delay` type.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-17-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Alexandru Ardelean [Thu, 26 Sep 2019 10:51:43 +0000 (13:51 +0300)]
spi: implement SW control for CS times
This change implements CS control for setup, hold & inactive delays.
The `cs_setup` delay is completely new, and can help with cases where
asserting the CS, also brings the device out of power-sleep, where there
needs to be a longer (than usual), before transferring data.
The `cs_hold` time can overlap with the `delay` (or `delay_usecs`) from an
SPI transfer. The main difference is that `cs_hold` implies that CS will be
de-asserted.
The `cs_inactive` delay does not have a clear use-case yet. It has been
implemented mostly because the `spi_set_cs_timing()` function implements
it. To some degree, this could overlap or replace `cs_change_delay`, but
this will require more consideration/investigation in the future.
All these delays have been added to the `spi_controller` struct, as they
would typically be configured by calling `spi_set_cs_timing()` after an
`spi_setup()` call.
Software-mode for CS control, implies that the `set_cs_timing()` hook has
not been provided for the `spi_controller` object.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-16-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Alexandru Ardelean [Thu, 26 Sep 2019 10:51:42 +0000 (13:51 +0300)]
spi: tegra114: change format for `spi_set_cs_timing()` function
The initial version of `spi_set_cs_timing()` was implemented with
consideration only for clock-cycles as delay.
For cases like `CS setup` time, it's sometimes needed that micro-seconds
(or nano-seconds) are required, or sometimes even longer delays, for cases
where the device needs a little longer to start transferring that after CS
is asserted.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-15-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Alexandru Ardelean [Thu, 26 Sep 2019 10:51:41 +0000 (13:51 +0300)]
spi: spidev: use new `delay` field for spi transfers
The `delay` field has type `struct spi_delay`.
This allows users to specify nano-second or clock-cycle delays (if needed).
Converting to use `delay` is straightforward: it's just assigning the
value to `delay.value` and hard-coding the `delay.unit` to
`SPI_DELAY_UNIT_USECS`.
This keeps the uapi for spidev un-changed. Changing it can be part of
another changeset and discussion.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-14-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Alexandru Ardelean [Thu, 26 Sep 2019 10:51:40 +0000 (13:51 +0300)]
spi: spi-loopback-test: use new `delay` field
This change replaces the use of the `delay_usecs` field with the new
`delay` field. The code/test still uses micro-seconds, but they are now
configured and used via the `struct spi_delay` format of the `delay` field.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-13-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Alexandru Ardelean [Thu, 26 Sep 2019 10:51:39 +0000 (13:51 +0300)]
spi: tegra20-sflash: use to new `spi_transfer_delay_exec`
This conversion to the spi_transfer_delay_exec() helper is not
straightforward, as it seems that when a delay is present, the controller
issues a command, and then a delay is followed.
This change adds support for the new `delay` field which is of type
`spi_delay` and keeps backwards compatibility with the old `delay_usecs`
field.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-12-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Alexandru Ardelean [Thu, 26 Sep 2019 10:51:38 +0000 (13:51 +0300)]
spi: tegra114: use `spi_transfer_delay_exec` helper
The tegra114 driver has a weird/separate `tegra_spi_transfer_delay()`
function that does 2 delays: one mdelay() and one udelay().
This was introduced via commit
f4fade12d506e14867a2b0a5e2f7aaf227297d8b
("spi/tegra114: Correct support for cs_change").
There doesn't seem to be a mention in that commit message to suggest a
specific need/use-case for having the 2 delay calls.
For the most part, udelay() should be sufficient.
This change replaces it with the new `spi_transfer_delay_exec()`, which
should do the same thing.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-11-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Alexandru Ardelean [Thu, 26 Sep 2019 10:51:36 +0000 (13:51 +0300)]
spi: introduce `delay` field for `spi_transfer` + spi_transfer_delay_exec()
The change introduces the `delay` field to the `spi_transfer` struct as an
`struct spi_delay` type.
This intends to eventually replace `delay_usecs`.
But, since there are many users of `delay_usecs`, this needs some
intermediate work.
A helper called `spi_transfer_delay_exec()` is also added, which maintains
backwards compatibility with `delay_usecs`, by assigning the value to
`delay` if non-zero.
This should maintain backwards compatibility with current users of
`udelay_usecs`.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-9-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Alexandru Ardelean [Thu, 26 Sep 2019 10:51:35 +0000 (13:51 +0300)]
spi: core,atmel: convert `word_delay_usecs` -> `word_delay` for spi_device
This change does a conversion from the `word_delay_usecs` -> `word_delay`
for the `spi_device` struct.
This allows users to specify inter-word delays in other unit types
(nano-seconds or clock cycles), depending on how users want.
The Atmel SPI driver is the only current user of the `word_delay_usecs`
field (from the `spi_device` struct).
So, it needed a slight conversion to use the `word_delay` as an `spi_delay`
struct.
In SPI core, the only required mechanism is to update the `word_delay`
information per `spi_transfer`. This requires a bit more logic than before,
because it needs that both delays be converted to a common unit
(nano-seconds) for comparison.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-8-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Alexandru Ardelean [Thu, 26 Sep 2019 10:51:34 +0000 (13:51 +0300)]
spi: spidev: use new `word_delay` field for spi transfers
The `word_delay` field had it's type changed to `struct spi_delay`.
This allows users to specify nano-second or clock-cycle delays (if needed).
Converting to use `word_delay` is straightforward: it's just assigning the
value to `word_delay.value` and hard-coding the `word_delay.unit` to
`SPI_DELAY_UNIT_USECS`
This keeps the uapi for spidev un-changed. Changing it can be part of
another changeset and discussion.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-7-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Alexandru Ardelean [Thu, 26 Sep 2019 10:51:33 +0000 (13:51 +0300)]
spi: orion: use new `word_delay` field for SPI transfers
The `word_delay` field had it's type changed to `struct spi_delay`.
This allows users to specify nano-second or clock-cycle delays (if needed).
Converting to use `word_delay` is straightforward: it just uses the new
`spi_delay_exec()` routine, that handles the `unit` part.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-6-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Alexandru Ardelean [Thu, 26 Sep 2019 10:51:32 +0000 (13:51 +0300)]
spi: sprd: convert transfer word delay to spi_delay struct
The Spreadtrum SPI driver is the only user of the `word_delay` field in
the `spi_transfer` struct.
This change converts the field to use the `spi_delay` struct. This also
enforces the users to specify the delay unit to be `SPI_DELAY_UNIT_SCK`.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-5-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Alexandru Ardelean [Thu, 26 Sep 2019 10:51:31 +0000 (13:51 +0300)]
spi: make `cs_change_delay` the first user of the `spi_delay` logic
Since the logic for `spi_delay` struct + `spi_delay_exec()` has been copied
from the `cs_change_delay` logic, it's natural to make this delay, the
first user.
The `cs_change_delay` logic requires that the default remain 10 uS, in case
it is unspecified/unconfigured. So, there is some special handling needed
to do that.
The ADIS library is one of the few users of the new `cs_change_delay`
parameter for an spi_transfer.
The introduction of the `spi_delay` struct, requires that the users of of
`cs_change_delay` get an update. This change also updates the ADIS library.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-4-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Alexandru Ardelean [Thu, 26 Sep 2019 10:51:30 +0000 (13:51 +0300)]
spi: introduce spi_delay struct as "value + unit" & spi_delay_exec()
There are plenty of delays that have been introduced in SPI core. Most of
them are in micro-seconds, some need to be in nano-seconds, and some in
clock-cycles.
For some of these delays (related to transfers & CS timing) it may make
sense to have a `spi_delay` struct that abstracts these a bit.
The important element of these delays [for unification] seems to be the
`unit` of the delay.
It looks like micro-seconds is good enough for most people, but every-once
in a while, some delays seem to require other units of measurement.
This change adds the `spi_delay` struct & a `spi_delay_exec()` function
that processes a `spi_delay` object/struct to execute the delay.
It's a copy of the `cs_change_delay` mechanism, but without the default
for 10 uS.
The clock-cycle delay unit is a bit special, as it needs to be bound to an
`spi_transfer` object to execute.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-3-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Alexandru Ardelean [Thu, 26 Sep 2019 10:51:29 +0000 (13:51 +0300)]
spi: move `cs_change_delay` backwards compat logic outside switch
The `cs_change_delay` backwards compatibility value could be moved outside
of the switch statement.
The only reason to do it, is to make the next patches easier to diff.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-2-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fabrizio Castro [Fri, 4 Oct 2019 08:35:28 +0000 (09:35 +0100)]
dt-bindings: spi: sh-msiof: Add r8a774b1 support
Document RZ/G2N (R8A774B1) SoC bindings.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/1570178133-21532-3-git-send-email-fabrizio.castro@bp.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Simon Horman [Thu, 26 Sep 2019 10:25:33 +0000 (12:25 +0200)]
dt-bindings: spi: sh-msiof: Convert bindings to json-schema
Convert Renesas HSPI bindings documentation to json-schema.
Also name bindings documentation file according to the compat string
being documented.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20190926102533.17829-1-horms+renesas@verge.net.au
Signed-off-by: Mark Brown <broonie@kernel.org>
zhengbin [Wed, 9 Oct 2019 00:37:17 +0000 (08:37 +0800)]
spi: npcm: Remove set but not used variable 'val'
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/spi/spi-npcm-pspi.c: In function npcm_pspi_handler:
drivers/spi/spi-npcm-pspi.c:296:6: warning: variable val set but not used [-Wunused-but-set-variable]
It is not used since commit
2a22f1b30cee ("spi:
npcm: add NPCM PSPI controller driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Link: https://lore.kernel.org/r/1570581437-104549-3-git-send-email-zhengbin13@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
zhengbin [Wed, 9 Oct 2019 00:37:16 +0000 (08:37 +0800)]
spi: omap-100k: Remove set but not used variable 'dataH'
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/spi/spi-omap-100k.c: In function spi100k_read_data:
drivers/spi/spi-omap-100k.c:140:6: warning: variable dataH set but not used [-Wunused-but-set-variable]
It is not used since commit
35c9049b2704 ("Add OMAP spi100k driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Link: https://lore.kernel.org/r/1570581437-104549-2-git-send-email-zhengbin13@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark Brown [Tue, 8 Oct 2019 18:12:28 +0000 (19:12 +0100)]
Merge branch 'for-5.4' of https://git./linux/kernel/git/broonie/spi into spi-5.5
Frieder Schrempf [Mon, 7 Oct 2019 07:23:02 +0000 (07:23 +0000)]
spi: spi-fsl-qspi: Clear TDH bits in FLSHCR register
Later versions of the QSPI controller (e.g. in i.MX6UL/ULL and i.MX7)
seem to have an additional TDH setting in the FLSHCR register, that
needs to be set in accordance with the access mode that is used (DDR
or SDR).
Previous bootstages such as BootROM or bootloader might have used the
DDR mode to access the flash. As we currently only use SDR mode, we
need to make sure the TDH bits are cleared upon initialization.
Fixes:
84d043185dbe ("spi: Add a driver for the Freescale/NXP QuadSPI controller")
Cc: <stable@vger.kernel.org>
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Acked-by: Han Xu <han.xu@nxp.com>
Link: https://lore.kernel.org/r/20191007071933.26786-1-frieder.schrempf@kontron.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Vladimir Oltean [Thu, 5 Sep 2019 01:01:14 +0000 (04:01 +0300)]
spi: spi-fsl-dspi: Always use the TCFQ devices in poll mode
With this patch, the "interrupts" property from the device tree bindings
is ignored, even if present, if the driver runs in TCFQ mode.
Switching to using the DSPI in poll mode has several distinct
benefits:
- With interrupts, the DSPI driver in TCFQ mode raises an IRQ after each
transmitted word. There is more time wasted for the "waitq" event than
for actual I/O. And the DSPI IRQ count can easily get the largest in
/proc/interrupts on Freescale boards with attached SPI devices.
- The SPI I/O time is both lower, and more consistently so. Attached to
some Freescale devices are either PTP switches, or SPI RTCs. For
reading time off of a SPI slave device, it is important that all SPI
transfers take a deterministic time to complete.
- In poll mode there is much less time spent by the CPU in hardirq
context, which helps with the response latency of the system, and at
the same time there is more control over when interrupts must be
disabled (to get a precise timestamp measurement): win-win.
On the LS1021A-TSN board, where the SPI device is a SJA1105 PTP switch
(with a bits_per_word=8 driver), I created a "benchmark" where I read
its PTP time once per second, for 120 seconds. Each "read PTP time" is a
12-byte SPI transfer. I then recorded the time before putting the first
byte in the TX FIFO, and the time after reading the last byte from the
RX FIFO. That is the transfer delay in nanoseconds.
Interrupt mode:
delay: min 125120 max 168320 mean 150286 std dev 17675.3
Poll mode:
delay: min 69440 max 119040 mean 70312.9 std dev 8065.34
Both the mean latency and the standard deviation are more than 50% lower
in poll mode than in interrupt mode. This is with an 'ondemand' governor
on an otherwise idle system - therefore running mostly at 600 MHz out of
a max of 1200 MHz.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20190905010114.26718-5-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Vladimir Oltean [Thu, 5 Sep 2019 01:01:13 +0000 (04:01 +0300)]
spi: spi-fsl-dspi: Implement the PTP system timestamping for TCFQ mode
In this mode, the DSPI controller uses PIO to transfer word by word. In
comparison, in EOQ mode the 4-word deep FIFO is being used, hence the
current logic will need some adaptation for which I do not have the
hardware (Coldfire) to test. It is not clear what is the timing of DMA
transfers and whether timestamping in the driver brings any overall
performance increase compared to regular timestamping done in the core.
Short phc2sys summary after 58 minutes of running on LS1021A-TSN with
interrupts disabled during the critical section:
offset: min -26251 max 16416 mean -21.8672 std dev 863.416
delay: min 4720 max 57280 mean 5182.49 std dev 1607.19
lost servo lock 3 times
Summary of the same phc2sys service running for 120 minutes with
interrupts disabled:
offset: min -378 max 381 mean -0.
0083089 std dev 101.495
delay: min 4720 max 5920 mean 5129.38 std dev 154.899
lost servo lock 0 times
The minimum delay (pre to post time) in nanoseconds is the same, but the
maximum delay is quite a bit higher, due to interrupts getting sometimes
executed and interfering with the measurement. Hence set disable_irqs
whenever possible (aka when the driver runs in poll mode - otherwise it
would be a contradiction in terms).
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20190905010114.26718-4-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Vladimir Oltean [Thu, 5 Sep 2019 01:01:12 +0000 (04:01 +0300)]
spi: Add a PTP system timestamp to the transfer structure
SPI is one of the interfaces used to access devices which have a POSIX
clock driver (real time clocks, 1588 timers etc). The fact that the SPI
bus is slow is not what the main problem is, but rather the fact that
drivers don't take a constant amount of time in transferring data over
SPI. When there is a high delay in the readout of time, there will be
uncertainty in the value that has been read out of the peripheral.
When that delay is constant, the uncertainty can at least be
approximated with a certain accuracy which is fine more often than not.
Timing jitter occurs all over in the kernel code, and is mainly caused
by having to let go of the CPU for various reasons such as preemption,
servicing interrupts, going to sleep, etc. Another major reason is CPU
dynamic frequency scaling.
It turns out that the problem of retrieving time from a SPI peripheral
with high accuracy can be solved by the use of "PTP system
timestamping" - a mechanism to correlate the time when the device has
snapshotted its internal time counter with the Linux system time at that
same moment. This is sufficient for having a precise time measurement -
it is not necessary for the whole SPI transfer to be transmitted "as
fast as possible", or "as low-jitter as possible". The system has to be
low-jitter for a very short amount of time to be effective.
This patch introduces a PTP system timestamping mechanism in struct
spi_transfer. This is to be used by SPI device drivers when they need to
know the exact time at which the underlying device's time was
snapshotted. More often than not, SPI peripherals have a very exact
timing for when their SPI-to-interconnect bridge issues a transaction
for snapshotting and reading the time register, and that will be
dependent on when the SPI-to-interconnect bridge figures out that this
is what it should do, aka as soon as it sees byte N of the SPI transfer.
Since spi_device drivers are the ones who'd know best how the peripheral
behaves in this regard, expose a mechanism in spi_transfer which allows
them to specify which word (or word range) from the transfer should be
timestamped.
Add a default implementation of the PTP system timestamping in the SPI
core. This is not going to be satisfactory performance-wise, but should
at least increase the likelihood that SPI device drivers will use PTP
system timestamping in the future.
There are 3 entry points from the core towards the SPI controller
drivers:
- transfer_one: The driver is passed individual spi_transfers to
execute. This is the easiest to timestamp.
- transfer_one_message: The core passes the driver an entire spi_message
(a potential batch of spi_transfers). The core puts the same pre and
post timestamp to all transfers within a message. This is not ideal,
but nothing better can be done by default anyway, since the core has
no insight into how the driver batches the transfers.
- transfer: Like transfer_one_message, but for unqueued drivers (i.e.
the driver implements its own queue scheduling).
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20190905010114.26718-3-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Stephen Boyd [Fri, 4 Oct 2019 21:43:32 +0000 (14:43 -0700)]
spi: gpio: Look for a device node instead of match
This driver doesn't do anything with the match for the device node. The
logic is the same as looking to see if a device node exists or not
because this driver wouldn't probe unless there is a device node match
when the device is created from DT. Just test for the presence of the
device node to simplify and avoid referencing a potentially undefined
match table when CONFIG_OF=n.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: <linux-spi@vger.kernel.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20191004214334.149976-9-swboyd@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Patrice Chotard [Fri, 4 Oct 2019 12:36:06 +0000 (14:36 +0200)]
spi: stm32-qspi: Fix kernel oops when unbinding driver
spi_master_put() must only be called in .probe() in case of error.
As devm_spi_register_master() is used during probe, spi_master_put()
mustn't be called in .remove() callback.
It fixes the following kernel WARNING/Oops when executing
echo "
58003000.spi" > /sys/bus/platform/drivers/stm32-qspi/unbind :
------------[ cut here ]------------
WARNING: CPU: 1 PID: 496 at fs/kernfs/dir.c:1504 kernfs_remove_by_name_ns+0x9c/0xa4
kernfs: can not remove 'uevent', no directory
Modules linked in:
CPU: 1 PID: 496 Comm: sh Not tainted
5.3.0-rc1-00219-ga0e07bb51a37 #62
Hardware name: STM32 (Device Tree Support)
[<
c0111570>] (unwind_backtrace) from [<
c010d384>] (show_stack+0x10/0x14)
[<
c010d384>] (show_stack) from [<
c08db558>] (dump_stack+0xb4/0xc8)
[<
c08db558>] (dump_stack) from [<
c01209d8>] (__warn.part.3+0xbc/0xd8)
[<
c01209d8>] (__warn.part.3) from [<
c0120a5c>] (warn_slowpath_fmt+0x68/0x8c)
[<
c0120a5c>] (warn_slowpath_fmt) from [<
c02e5844>] (kernfs_remove_by_name_ns+0x9c/0xa4)
[<
c02e5844>] (kernfs_remove_by_name_ns) from [<
c05833a4>] (device_del+0x128/0x358)
[<
c05833a4>] (device_del) from [<
c05835f8>] (device_unregister+0x24/0x64)
[<
c05835f8>] (device_unregister) from [<
c0638dac>] (spi_unregister_controller+0x88/0xe8)
[<
c0638dac>] (spi_unregister_controller) from [<
c058c580>] (release_nodes+0x1bc/0x200)
[<
c058c580>] (release_nodes) from [<
c0588a44>] (device_release_driver_internal+0xec/0x1ac)
[<
c0588a44>] (device_release_driver_internal) from [<
c0586840>] (unbind_store+0x60/0xd4)
[<
c0586840>] (unbind_store) from [<
c02e64e8>] (kernfs_fop_write+0xe8/0x1c4)
[<
c02e64e8>] (kernfs_fop_write) from [<
c0266b44>] (__vfs_write+0x2c/0x1c0)
[<
c0266b44>] (__vfs_write) from [<
c02694c0>] (vfs_write+0xa4/0x184)
[<
c02694c0>] (vfs_write) from [<
c0269710>] (ksys_write+0x58/0xd0)
[<
c0269710>] (ksys_write) from [<
c0101000>] (ret_fast_syscall+0x0/0x54)
Exception stack(0xdd289fa8 to 0xdd289ff0)
9fa0:
0000006c 000e20e8 00000001 000e20e8 0000000d 00000000
9fc0:
0000006c 000e20e8 b6f87da0 00000004 0000000d 0000000d 00000000 00000000
9fe0:
00000004 bee639b0 b6f2286b b6eaf6c6
---[ end trace
1b15df8a02d76aef ]---
------------[ cut here ]------------
WARNING: CPU: 1 PID: 496 at fs/kernfs/dir.c:1504 kernfs_remove_by_name_ns+0x9c/0xa4
kernfs: can not remove 'online', no directory
Modules linked in:
CPU: 1 PID: 496 Comm: sh Tainted: G W
5.3.0-rc1-00219-ga0e07bb51a37 #62
Hardware name: STM32 (Device Tree Support)
[<
c0111570>] (unwind_backtrace) from [<
c010d384>] (show_stack+0x10/0x14)
[<
c010d384>] (show_stack) from [<
c08db558>] (dump_stack+0xb4/0xc8)
[<
c08db558>] (dump_stack) from [<
c01209d8>] (__warn.part.3+0xbc/0xd8)
[<
c01209d8>] (__warn.part.3) from [<
c0120a5c>] (warn_slowpath_fmt+0x68/0x8c)
[<
c0120a5c>] (warn_slowpath_fmt) from [<
c02e5844>] (kernfs_remove_by_name_ns+0x9c/0xa4)
[<
c02e5844>] (kernfs_remove_by_name_ns) from [<
c0582488>] (device_remove_attrs+0x20/0x5c)
[<
c0582488>] (device_remove_attrs) from [<
c05833b0>] (device_del+0x134/0x358)
[<
c05833b0>] (device_del) from [<
c05835f8>] (device_unregister+0x24/0x64)
[<
c05835f8>] (device_unregister) from [<
c0638dac>] (spi_unregister_controller+0x88/0xe8)
[<
c0638dac>] (spi_unregister_controller) from [<
c058c580>] (release_nodes+0x1bc/0x200)
[<
c058c580>] (release_nodes) from [<
c0588a44>] (device_release_driver_internal+0xec/0x1ac)
[<
c0588a44>] (device_release_driver_internal) from [<
c0586840>] (unbind_store+0x60/0xd4)
[<
c0586840>] (unbind_store) from [<
c02e64e8>] (kernfs_fop_write+0xe8/0x1c4)
[<
c02e64e8>] (kernfs_fop_write) from [<
c0266b44>] (__vfs_write+0x2c/0x1c0)
[<
c0266b44>] (__vfs_write) from [<
c02694c0>] (vfs_write+0xa4/0x184)
[<
c02694c0>] (vfs_write) from [<
c0269710>] (ksys_write+0x58/0xd0)
[<
c0269710>] (ksys_write) from [<
c0101000>] (ret_fast_syscall+0x0/0x54)
Exception stack(0xdd289fa8 to 0xdd289ff0)
9fa0:
0000006c 000e20e8 00000001 000e20e8 0000000d 00000000
9fc0:
0000006c 000e20e8 b6f87da0 00000004 0000000d 0000000d 00000000 00000000
9fe0:
00000004 bee639b0 b6f2286b b6eaf6c6
---[ end trace
1b15df8a02d76af0 ]---
8<--- cut here ---
Unable to handle kernel NULL pointer dereference at virtual address
00000050
pgd =
e612f14d
[
00000050] *pgd=
ff1f5835
Internal error: Oops: 17 [#1] SMP ARM
Modules linked in:
CPU: 1 PID: 496 Comm: sh Tainted: G W
5.3.0-rc1-00219-ga0e07bb51a37 #62
Hardware name: STM32 (Device Tree Support)
PC is at kernfs_find_ns+0x8/0xfc
LR is at kernfs_find_and_get_ns+0x30/0x48
pc : [<
c02e49a4>] lr : [<
c02e4ac8>] psr:
40010013
sp :
dd289dac ip :
00000000 fp :
00000000
r10:
00000000 r9 :
def6ec58 r8 :
dd289e54
r7 :
00000000 r6 :
c0abb234 r5 :
00000000 r4 :
c0d26a30
r3 :
ddab5080 r2 :
00000000 r1 :
c0abb234 r0 :
00000000
Flags: nZcv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
Control:
10c5387d Table:
dd11c06a DAC:
00000051
Process sh (pid: 496, stack limit = 0xe13a592d)
Stack: (0xdd289dac to 0xdd28a000)
9da0:
c0d26a30 00000000 c0abb234 00000000 c02e4ac8
9dc0:
00000000 c0976b44 def6ec00 dea53810 dd289e54 c02e864c c0a61a48 c0a4a5ec
9de0:
c0d630a8 def6ec00 c0d04c48 c02e86e0 def6ec00 de909338 c0d04c48 c05833b0
9e00:
00000000 c0638144 dd289e54 def59900 00000000 475b3ee5 def6ec00 00000000
9e20:
def6ec00 def59b80 dd289e54 def59900 00000000 c05835f8 def6ec00 c0638dac
9e40:
0000000a dea53810 c0d04c48 c058c580 dea53810 def59500 def59b80 475b3ee5
9e60:
ddc63e00 dea53810 dea3fe10 c0d63a0c dea53810 ddc63e00 dd289f78 dd240d10
9e80:
00000000 c0588a44 c0d59a20 0000000d c0d63a0c c0586840 0000000d dd240d00
9ea0:
00000000 00000000 ddc63e00 c02e64e8 00000000 00000000 c0d04c48 dd9bbcc0
9ec0:
c02e6400 dd289f78 00000000 000e20e8 0000000d c0266b44 00000055 00000cc0
9ee0:
000000e3 000e3000 dd11c000 dd11c000 00000000 00000000 00000000 00000000
9f00:
ffeee38c dff99688 00000000 475b3ee5 00000001 dd289fb0 ddab5080 ddaa5800
9f20:
00000817 000e30ec dd9e7720 475b3ee5 ddaa583c 0000000d dd9bbcc0 000e20e8
9f40:
dd289f78 00000000 000e20e8 0000000d 00000000 c02694c0 00000000 00000000
9f60:
c0d04c48 dd9bbcc0 00000000 00000000 dd9bbcc0 c0269710 00000000 00000000
9f80:
000a91f4 475b3ee5 0000006c 000e20e8 b6f87da0 00000004 c0101204 dd288000
9fa0:
00000004 c0101000 0000006c 000e20e8 00000001 000e20e8 0000000d 00000000
9fc0:
0000006c 000e20e8 b6f87da0 00000004 0000000d 0000000d 00000000 00000000
9fe0:
00000004 bee639b0 b6f2286b b6eaf6c6 600e0030 00000001 00000000 00000000
[<
c02e49a4>] (kernfs_find_ns) from [<
def6ec00>] (0xdef6ec00)
Code:
ebf8eeab c0dc50b8 e92d40f0 e292c000 (
e1d035b0)
---[ end trace
1b15df8a02d76af1 ]---
Fixes:
a88eceb17ac7 ("spi: stm32-qspi: add spi_master_put in release function")
Cc: <stable@vger.kernel.org>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Link: https://lore.kernel.org/r/20191004123606.17241-1-patrice.chotard@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Vladimir Oltean [Tue, 1 Oct 2019 20:52:16 +0000 (23:52 +0300)]
spi: spi-fsl-dspi: Always use the TCFQ devices in poll mode
With this patch, the "interrupts" property from the device tree bindings
is ignored, even if present, if the driver runs in TCFQ mode.
Switching to using the DSPI in poll mode has several distinct
benefits:
- With interrupts, the DSPI driver in TCFQ mode raises an IRQ after each
transmitted word. There is more time wasted for the "waitq" event than
for actual I/O. And the DSPI IRQ count can easily get the largest in
/proc/interrupts on Freescale boards with attached SPI devices.
- The SPI I/O time is both lower, and more consistently so. Attached to
some Freescale devices are either PTP switches, or SPI RTCs. For
reading time off of a SPI slave device, it is important that all SPI
transfers take a deterministic time to complete.
- In poll mode there is much less time spent by the CPU in hardirq
context, which helps with the response latency of the system, and at
the same time there is more control over when interrupts must be
disabled (to get a precise timestamp measurement, which will come in a
future patch): win-win.
On the LS1021A-TSN board, where the SPI device is a SJA1105 PTP switch
(with a bits_per_word=8 driver), I created a "benchmark" where I
periodically transferred a 12-byte message once per second, for 120
seconds. I then recorded the time before putting the first byte in the
TX FIFO, and the time after reading the last byte from the RX FIFO. That
is the transfer delay in nanoseconds.
Interrupt mode:
delay: min 125120 max 168320 mean 150286 std dev 17675.3
Poll mode:
delay: min 69440 max 119040 mean 70312.9 std dev 8065.34
Both the mean latency and the standard deviation are more than 50% lower
in poll mode than in interrupt mode, and the 'max' in poll mode is lower
than the 'min' in interrupt mode. This is with an 'ondemand' governor on
an otherwise idle system - therefore running mostly at 600 MHz out of a
max of 1200 MHz.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20191001205216.32115-1-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Felipe Balbi [Tue, 1 Oct 2019 08:14:05 +0000 (11:14 +0300)]
SPI: designware: pci: Switch over to MSI interrupts
Some devices support MSI interrupts. Let's at least try to use them in
platforms that provide MSI capability.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Link: https://lore.kernel.org/r/20191001081405.764161-1-felipe.balbi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Kuldeep Singh [Tue, 1 Oct 2019 08:59:16 +0000 (14:29 +0530)]
spi: spi-fsl-qspi: Introduce variable to fix different invalid master Id
Different platforms have different Master with different SourceID on
AHB bus. The 0X0E Master ID is used by cluster 3 in case of LS2088A.
So, patch introduce an invalid master id variable to fix invalid
mastered on different platforms.
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Link: https://lore.kernel.org/r/1569920356-8953-1-git-send-email-kuldeep.singh@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>