OSDN Git Service
David S. Miller [Mon, 9 Oct 2017 23:38:52 +0000 (16:38 -0700)]
Merge branch '10GbE' of git://git./linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
10GbE Intel Wired LAN Driver Updates 2017-10-09
This series contains updates to ixgbe only.
Emil fixes an issue where the semaphore bits could be stuck after a reset
or a crash, by adding the clearing of software resource bits in the
software/firmware synchronization register. Added error checks when we
attempt to identify and initialize the PHY to prevent a crash. Fixed a
few issues in the logic of ixgbe_clean_test_rings() which was exposed by
a previous commit that was causing a crash in ethtool diagnostics.
Bhumika Goyal fixes a couple of instances which were overlooked when we
made ixgbe_mac_operations constant.
Shannon Nelson fixes an issue to restore normal operations after the
last MACVLAN offload is removed, otherwise we get stuck in a single queue
operations.
The infamous Jesper Dangaard Brouer adds a counter which counts the
number of times the recycle fails and the real page allocator is invoked.
Alex updates the adaptive ITR algorithm to better support the needs of the
network. This attempt to make it so that our ITR algorithm will try to
prevent either starving a socket buffer for memory in the case of
transmit, or overrunning an receive socket buffer on receive. We should
function better with new features like XDP which can handle small packets
at high rates without needing to lock us into NAPI polling mode.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 9 Oct 2017 17:47:30 +0000 (10:47 -0700)]
Merge branch 'ipv6-addrlabel-avoid-dirtying-ip6addrlbl_entry'
Eric Dumazet says:
====================
ipv6: addrlabel: avoid dirtying ip6addrlbl_entry
The refcount on ip6addrlbl_entry is only used to make sure ip6addrlbl_entry
does not disappear while ip6addrlbl_get() is allocating an skb.
We can instead allocate skb first, then use RCU, so that we no longer need
to refcount these structures.
====================
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 9 Oct 2017 16:52:25 +0000 (09:52 -0700)]
ipv6: addrlabel: remove refcounting
After previous patch ("ipv6: addrlabel: rework ip6addrlbl_get()")
we can remove the refcount from struct ip6addrlbl_entry,
since it is no longer elevated in p6addrlbl_get()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 9 Oct 2017 16:52:24 +0000 (09:52 -0700)]
ipv6: addrlabel: rework ip6addrlbl_get()
If we allocate skb before the lookup, we can use RCU
without the need of ip6addrlbl_hold()
This means that the following patch can get rid of refcounting.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 9 Oct 2017 17:33:06 +0000 (10:33 -0700)]
Merge branch 'mlx4-static-checker-warnings'
Tariq Toukan says:
====================
Fix mlx4 static checker warnings
This patchset contains fixes for static checker warnings
in the mlx4 Core and Eth drivers.
Patch 1 fixes an actual bug discovered by the checker.
Patches 2 and 3 fix the warnings without functional changes.
Series generated against net-next commit:
c49c777f9c87 qed: Delete redundant check on dcb_app priority
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tariq Toukan [Mon, 9 Oct 2017 13:59:50 +0000 (16:59 +0300)]
net/mlx4_en: Use __force to fix a sparse warning in TX datapath
In TX data-path, we intentionally do not byte-swap, as documented
in code and in the cited commit log.
This fixes sparse warning:
en_tx.c:720:23: warning: incorrect type in argument 1 (different base types)
en_tx.c:720:23: expected unsigned int [unsigned] [usertype] <noident>
en_tx.c:720:23: got restricted __be32 [usertype] doorbell_qpn
Fixes:
492f5add4be8 ("net/mlx4_en: Doorbell is byteswapped in Little Endian archs")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tariq Toukan [Mon, 9 Oct 2017 13:59:49 +0000 (16:59 +0300)]
net/mlx4_core: Fix cast warning in fw.c
Fix the following SPARSE warning, in MLX4_GET() macro:
drivers/net/ethernet/mellanox/mlx4/fw.c:233:9: warning: cast to restricted __be64
Fixes:
17d5ceb6e43e ("net/mlx4_core: Fix unaligned accesses")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tariq Toukan [Mon, 9 Oct 2017 13:59:48 +0000 (16:59 +0300)]
net/mlx4: Fix endianness issue in qp context params
Should take care of the endianness before assigning to params2 field.
Fixes:
53f33ae295a5 ("net/mlx4_core: Port aggregation upper layer interface")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mika Westerberg [Mon, 9 Oct 2017 13:22:34 +0000 (16:22 +0300)]
thunderbolt: Initialize Thunderbolt bus earlier
The 0day kbuild robot reports following crash:
BUG: unable to handle kernel NULL pointer dereference at
00000004
IP: tb_property_find+0xe/0x41
*pde =
00000000
Oops: 0000 [#1]
CPU: 0 PID: 1 Comm: swapper Not tainted
4.14.0-rc1-00741-ge69b6c0 #412
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1 04/01/2014
task:
89c80000 task.stack:
89c7c000
EIP: tb_property_find+0xe/0x41
EFLAGS:
00210246 CPU: 0
EAX:
00000000 EBX:
7a368f47 ECX:
00000044 EDX:
7a368f47
ESI:
8851d340 EDI:
7a368f47 EBP:
89c7df0c ESP:
89c7defc
DS: 007b ES: 007b FS: 0000 GS: 0000 SS: 0068
CR0:
80050033 CR2:
00000004 CR3:
027a2000 CR4:
00000690
Call Trace:
tb_register_property_dir+0x49/0xb9
? cdc_mbim_driver_init+0x1b/0x1b
tbnet_init+0x77/0x9f
? cdc_mbim_driver_init+0x1b/0x1b
do_one_initcall+0x7e/0x145
? parse_args+0x10c/0x1b3
? kernel_init_freeable+0xbe/0x159
kernel_init_freeable+0xd1/0x159
? rest_init+0x110/0x110
kernel_init+0xd/0xd0
ret_from_fork+0x19/0x30
The reason is that both Thunderbolt bus and thunderbolt-net are build
into the kernel image, and the latter is linked first because
drivers/net comes before drivers/thunderbolt. Since both use
module_init() thunderbolt-net ends up calling Thunderbolt bus functions
too early triggering the above crash.
Fix this by moving Thunderbolt bus initialization to happen earlier to
make sure all the data structures are ready when Thunderbolt service
drivers are initialized. To be on the safe side also add a check for
properly initialized xdomain_property_dir to tb_register_property_dir().
Reported-by: kernel test robot <fengguang.wu@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 9 Oct 2017 13:01:37 +0000 (06:01 -0700)]
ipv6: avoid zeroing per cpu data again
per cpu allocations are already zeroed, no need to clear them again.
Fixes:
d52d3997f843f ("ipv6: Create percpu rt6_info")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Martin KaFai Lau <kafai@fb.com>
Cc: Tejun Heo <tj@kernel.org>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 9 Oct 2017 17:21:27 +0000 (10:21 -0700)]
Merge branch 'qed-Add-iWARP-support-for-unaligned-MPA-packets'
Michal Kalderon says:
====================
qed: Add iWARP support for unaligned MPA packets
This patch series adds support for handling unaligned MPA packets.
(FPDUs split over more than one tcp packet).
When FW detects a packet is unaligned it fowards the packet to
the driver via a light l2 dedicated connection. The driver then
stores this packet until the remainder of the packet is received.
Once the driver reconstructs the full FPDU, it sends it down
to fw via the ll2 connection. Driver also breaks down any packed
PDUs into separate packets for FW.
Patches 1-6 are all slight modifications to ll2 to support additional
requirements for the unaligned MPA ll2 client.
Patch 7 opens the additional ll2 connection for iWARP.
Patches 8-12 contain the algorithm for aligning packets.
====================
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kalderon [Mon, 9 Oct 2017 09:37:54 +0000 (12:37 +0300)]
qed: Add iWARP support for fpdu spanned over more than two tcp packets
We continue to maintain a maximum of three buffers per fpdu, to ensure
that there are enough buffers for additional unaligned mpa packets.
To support this, if a fpdu is split over more than two tcp packets, we
use an intermediate buffer to copy the data to the previous buffer, then
we can release the data. We need an intermediate buffer as the initial
buffer partial packet could be located at the end of the packet, not
leaving room for additional data. This is a corner case, and will usually
not be the case.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kalderon [Mon, 9 Oct 2017 09:37:53 +0000 (12:37 +0300)]
qed: Add support for MPA header being split over two tcp packets
There is a special case where an MPA header is split over to tcp
packets, in this case we need to wait for the next packet to
get the fpdu length. We use the incomplete_bytes to mark this
fpdu as a "special" one which requires updating the length with
the next packet
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kalderon [Mon, 9 Oct 2017 09:37:52 +0000 (12:37 +0300)]
qed: Add support for freeing two ll2 buffers for corner cases
When posting a packet on the ll2 tx, we can provide a cookie that
will be returned upon tx completion. This cookie is the ll2 iwarp buffer
which is then reposted to the rx ring. Part of the unaligned mpa flow
is determining when a buffer can be reposted. Each buffer needs to be
sent only once as a cookie for on the tx ring. In packed fpdu case, only
the last packet will be sent with the buffer, meaning we need to handle the
case that a cookie can be NULL on tx complete. In addition, when a fpdu
splits over two buffers, but there are no more fpdus on the second buffer,
two buffers need to be provided as a cookie. To avoid changing the ll2
interface to provide two cookies, we introduce a piggy buf pointer,
relevant for iWARP only, that holds a pointer to a second buffer that
needs to be released during tx completion.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kalderon [Mon, 9 Oct 2017 09:37:51 +0000 (12:37 +0300)]
qed: Add unaligned and packed packet processing
The fpdu data structure is preallocated per connection.
Each connection stores the current status of the connection:
either nothing pending, or there is a partial fpdu that is waiting for
the rest of the fpdu (incomplete bytes != 0).
The same structure is also used for splitting a packet when there are
packed fpdus. The structure is initialized with all data required
for sending the fpdu back to the FW. A fpdu will always be spanned across
a maximum of 3 tx bds. One for the header, one for the partial fdpu
received and one for the remainder (unaligned) packet.
In case of packed fpdu's, two fragments are used, one for the header
and one for the data.
Corner cases are not handled in the patch for clarity, and will be added
as a separate patch.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kalderon [Mon, 9 Oct 2017 09:37:50 +0000 (12:37 +0300)]
qed: Add mpa buffer descriptors for storing and processing mpa fpdus
The mpa buff is a descriptor for iwarp ll2 buffers that contains
additional information required for aligining fpdu's.
In some cases, an additional packet will arrive which will complete
the alignment of a fpdu, but we won't be able to post the fpdu due to
insufficient place on the tx ring. In this case we can't loose the data
and require storing it for later. Processing is therefore done
in two places, during rx completion, where we initialize a mpa buffer
descriptor and add it to the pending list, and during tx-completion, since
we free up an entry in the tx chain we can process any pending mpa packets.
The mpa buff descriptors are pre-allocated since we have to ensure that
we won't reach a state where we can't store an incoming unaligned packet.
All packets received on the ll2 MUST be processed by the driver at some
stage. Since they are preallocated, we hold a free list.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kalderon [Mon, 9 Oct 2017 09:37:49 +0000 (12:37 +0300)]
qed: Add ll2 connection for processing unaligned MPA packets
This patch adds only the establishment and termination of the
ll2 connection that handles unaligned MPA packets.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kalderon [Mon, 9 Oct 2017 09:37:48 +0000 (12:37 +0300)]
qed: Add LL2 slowpath handling
For iWARP unaligned MPA flow, a slowpath event of flushing an
MPA connection that entered an unaligned state is required.
The flush ramrod is received on the ll2 queue, and a pre-registered
callback function is called to handle the flush event.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kalderon [Mon, 9 Oct 2017 09:37:47 +0000 (12:37 +0300)]
qed: Add the source of a packet sent on an iWARP ll2 connection
When a packet is sent back to iWARP FW via the tx ll2 connection
the FW needs to know the source of the packet. Whether it is
OOO or unaligned MPA related. Since OOO is implemented entirely
inside the ll2 code (and shared with iSCSI), packets are marked
as IN_ORDER inside the ll2 code. For unaligned mpa the value
will be determined in the iWARP code and sent on the pkt->vlan
field.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kalderon [Mon, 9 Oct 2017 09:37:46 +0000 (12:37 +0300)]
qed: Fix initialization of ll2 offload feature
enable_ip_cksum, enable_l4_cksum, calc_ip_len were added in
commit stated below but not passed through to FW. This was OK
until now as it wasn't used, but is required for the iWARP
unaligned flow
Fixes:
7c7973b2ae27 ("qed: LL2 to use packed information for tx")
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kalderon [Mon, 9 Oct 2017 09:37:45 +0000 (12:37 +0300)]
qed: Add ll2 option for dropping a tx packet
The option of sending a packet on the ll2 and dropping it exists in
hardware and was not used until now, thus not exposed.
The iWARP unaligned MPA flow requires this functionality for
flushing the tx queue.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kalderon [Mon, 9 Oct 2017 09:37:44 +0000 (12:37 +0300)]
qed: Add ll2 ability of opening a secondary queue
When more than one ll2 queue is opened ( that is not an OOO queue )
ll2 code does not have enough information to determine whether
the queue is the main one or not, so a new field is added to the
acquire input data to expose the control of determining whether
the queue is the main queue or a secondary queue.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kalderon [Mon, 9 Oct 2017 09:37:43 +0000 (12:37 +0300)]
qed: Add ll2 option to limit the number of bds per packet
iWARP uses 3 ll2 connections, the maximum number of bds is known
during connection setup. This patch modifies the static array in
the ll2_tx_packet descriptor to be a flexible array and
significantlly reduces memory size.
In addition, some redundant fields in the ll2_tx_packet were
removed, which also contributed to decreasing the descriptor size.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 9 Oct 2017 17:18:12 +0000 (10:18 -0700)]
Merge branch 'mlxsw-Offload-bridge-device-mrouter'
Jiri Pirko says:
====================
mlxsw: Offload bridge device mrouter
Yotam says:
Similarly to a bridged port, the bridge device itself can be configured by
the user to be an mrouter port. In this case, all multicast traffic should
be forwarded to it. Make the mlxsw Spectrum driver offload these directives
to the Spectrum hardware.
Patches 1 and 2 add a new switchdev notification for bridge device mrouter
port status and make the bridge module notify about it.
Patches 3-5 change the mlxsw Spectrum driver to handle these notifications
by adding the Spectrum router port to the bridge MDB entries.
v1->v2:
- patch1:
- Don't add the MDB_RTR_TYPE_TEMP state and use the timer_pending to
distinguish between learning-on and learning-off states
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Yotam Gigi [Mon, 9 Oct 2017 09:15:35 +0000 (11:15 +0200)]
mlxsw: spectrum_switchdev: Support bridge mrouter notifications
Support the SWITCHDEV_ATTR_ID_BRIDGE_MROUTER port attribute switchdev
notification.
To do that, add the mrouter flag to struct mlxsw_sp_bridge_device, which
indicates whether the bridge device was set to be mrouter port. This field
is set when:
- A new bridge is created, where the value is taken from the kernel
bridge value.
- A switchdev SWITCHDEV_ATTR_ID_BRIDGE_MROUTER notification is sent.
In addition, change the bridge MID entries to include the router port when
the bridge device is configured to be mrouter port. The MID entries are
updated in the following cases:
- When a new MID entry is created, update the router port according to the
bridge mrouter state.
- When a SWITCHDEV_ATTR_ID_BRIDGE_MROUTER notification is sent, update all
the bridge's MID entries.
This is aligned with the case where a bridge slave is configured to be
mrouter port.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yotam Gigi [Mon, 9 Oct 2017 09:15:34 +0000 (11:15 +0200)]
mlxsw: spectrum_switchdev: Add support for router port in SMID entries
In Spectrum, MDB entries point to MID entries, that indicate which ports a
packet should be forwarded to. Add the support in creating MID entries that
forward the packet to the Spectrum router port.
This will be later used to handle the bridge mrouter port switchdev
notifications.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yotam Gigi [Mon, 9 Oct 2017 09:15:33 +0000 (11:15 +0200)]
mlxsw: spectrum: router: Export the mlxsw_sp_router_port function
In Spectrum hardware, the router port is a virtual port that is the gateway
to the routing mechanism. Hence, in order for a packet to be L3 forwarded,
it must first be L2 forwarded to the router port inside the hardware.
Further patches in this patchset are going to introduce support in bridge
device used as an mrouter port. In this case, the router port index will be
needed in order to update the MDB entries to include the router port. Thus,
export the mlxsw_sp_router_port function, which returns the index of the
Spectrum router port.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yotam Gigi [Mon, 9 Oct 2017 09:15:32 +0000 (11:15 +0200)]
net: bridge: Export bridge multicast router state
Add an access function that, given a bridge netdevice, returns whether the
bridge device is currently an mrouter or not. The function uses the already
existing br_multicast_is_router function to check that.
This function is needed in order to allow ports that join an already
existing bridge to know the current mrouter state of the bridge device.
Together with the bridge device mrouter ports switchdev notifications, it
is possible to have full offloading of the semantics of the bridge device
mcast router state.
Due to the fact that the bridge multicast router status can change in
packet RX path, take the multicast_router bridge spinlock to protect the
read.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yotam Gigi [Mon, 9 Oct 2017 09:15:31 +0000 (11:15 +0200)]
net: bridge: Notify on bridge device mrouter state changes
Add the SWITCHDEV_ATTR_ID_BRIDGE_MROUTER switchdev notification type, used
to indicate whether the bridge is or isn't mrouter. Notify when the bridge
changes its state, similarly to the already existing bridged port mrouter
notifications.
The notification uses the switchdev_attr.u.mrouter boolean flag to indicate
the current bridge mrouter status. Thus, it only indicates whether the
bridge is currently used as an mrouter or not, and does not indicate the
exact mrouter state of the bridge (learning, permanent, etc.).
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Emil Tantilov [Fri, 29 Sep 2017 17:55:42 +0000 (10:55 -0700)]
ixgbe: fix crash when injecting AER after failed reset
In case where AER recovery fails the device is left in a down state.
Consecutive AER error injection can lead to a double IRQ free.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alexander Duyck [Mon, 25 Sep 2017 21:55:36 +0000 (14:55 -0700)]
ixgbe: Update adaptive ITR algorithm
The following change is meant to update the adaptive ITR algorithm to
better support the needs of the network. Specifically with this change what
I have done is make it so that our ITR algorithm will try to prevent either
starving a socket buffer for memory in the case of Tx, or overrunning an Rx
socket buffer on receive.
In addition a side effect of the calculations used is that we should
function better with new features such as XDP which can handle small
packets at high rates without needing to lock us into NAPI polling mode.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Emil Tantilov [Mon, 11 Sep 2017 21:21:36 +0000 (14:21 -0700)]
ixgbe: fix the FWSM.PT check in ixgbe_mng_present()
Bits other than FWSM.PT can be set in IXGBE_SWFW_MODE_MASK making the
previous check invalid.
Change the check for MNG present to be only based on FWSM.PT bit.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Emil Tantilov [Mon, 11 Sep 2017 21:21:31 +0000 (14:21 -0700)]
ixgbe: fix use of uninitialized padding
This patch is resolving Coverity hits where padding in a structure could
be used uninitialized.
- Initialize fwd_cmd.pad/2 before ixgbe_calculate_checksum()
- Initialize buffer.pad2/3 before ixgbe_hic_unlocked()
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jesper Dangaard Brouer [Mon, 4 Sep 2017 18:40:22 +0000 (20:40 +0200)]
ixgbe: add counter for times Rx pages gets allocated, not recycled
The ixgbe driver have page recycle scheme based around the RX-ring
queue, where a RX page is shared between two packets. Based on the
refcnt, the driver can determine if the RX-page is currently only used
by a single packet, if so it can then directly refill/recycle the
RX-slot by with the opposite "side" of the page.
While this is a clever trick, it is hard to determine when this
recycling is successful and when it fails. Adding a counter, which is
available via ethtool --statistics as 'alloc_rx_page'. Which counts
the number of times the recycle fails and the real page allocator is
invoked. When interpreting the stats, do remember that every alloc
will serve two packets.
The counter is collected per rx_ring, but is summed and ethtool
exported as 'alloc_rx_page'. It would be relevant to know what
rx_ring that cannot keep up, but that can be exported later if
someone experience a need for this.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
David S. Miller [Mon, 9 Oct 2017 16:51:03 +0000 (09:51 -0700)]
Merge branch 'nfp-bpf-ABIv2-and-multi-port'
Jakub Kicinski says:
====================
nfp: bpf ABIv2 and multi port
This series migrates our eBPF offload from old PoC firmware to
a redesigned, faster and more feature rich FW. Marking support
is dropped for now. We have to teach the JIT about encoding
local memory accesses (one of NFP memory types). There is also
code to populate the ECC of instructions (PoC had ECC protection
on instruction store disabled). There is also a minor ld_field
fix and all 64 bit shifts can now be encoded.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 9 Oct 2017 04:04:17 +0000 (21:04 -0700)]
nfp: bpf: pass dst register to ld_field instruction
ld_field instruction is a bit special because the encoding uses
two source registers and one of them becomes the output. We do
need to pass the dst register to our encoding helpers though,
otherwise the "write both banks" flag will not be observed.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 9 Oct 2017 04:04:16 +0000 (21:04 -0700)]
nfp: bpf: byte swap the instructions
Device expects the instructions in little endian. Make sure we
byte swap on big endian hosts.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 9 Oct 2017 04:04:15 +0000 (21:04 -0700)]
nfp: bpf: pad code with valid nops
We need to append up to 8 nops after last instruction to make
sure the CPU will not fetch garbage instructions with invalid
ECC if the code store was not initialized.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 9 Oct 2017 04:04:14 +0000 (21:04 -0700)]
nfp: bpf: calculate code store ECC
In the initial PoC firmware I simply disabled ECC on the instruction
store. Do the ECC calculation for generated instructions in the driver.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 9 Oct 2017 04:04:13 +0000 (21:04 -0700)]
nfp: bpf: move to datapath ABI version 2
Datapath ABI version 2 stores the packet information in LMEM
instead of NNRs. We also have strict restrictions on which
GPRs we can use. Only GPRs 0-23 are reserved for BPF.
Adjust the static register locations and "ABI" registers.
Note that packet length is packed with other info so we have
to extract it into one of the scratch registers, OTOH since
LMEM can be used in restricted operands we don't have to
extract packet pointer.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 9 Oct 2017 04:04:12 +0000 (21:04 -0700)]
nfp: bpf: encode extended LM pointer operands
Most instructions have special fields which allow switching
between base and extended Local Memory pointers. Introduce
those to register encoding, we will use the extra LM pointers
to access high addresses of the stack.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 9 Oct 2017 04:04:11 +0000 (21:04 -0700)]
nfp: bpf: encode LMEM accesses
NFP LMEM is a large, indirectly accessed register file. There
are two basic indirect access registers. Each access operation
may either use offset (up to 8 or 16 words) or perform post
decrement/increment.
Add encodings of LMEM indexes as instruction operands.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 9 Oct 2017 04:04:10 +0000 (21:04 -0700)]
nfp: add more white space to the instruction defines
We need to add longer OP_* defines, move the values away.
Purely whitespace commit.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 9 Oct 2017 04:04:09 +0000 (21:04 -0700)]
nfp: bpf: remove packet marking support
Temporarily drop support for skb->mark. We are primarily focusing
on XDP offload, and implementing skb->mark on the new datapath has
lower priority.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 9 Oct 2017 04:04:08 +0000 (21:04 -0700)]
nfp: bpf: remove register rename
Remove the register renumbering optimization. To implement calling
map and other helpers we need more strict register layout. We can't
freely reassign register numbers.
This will have the effect of running in 4 context/thread mode, which
should be OK since we are moving towards integrating the BPF closer
with FW app datapath anyway, and the target datapath itself runs in
4 context mode.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 9 Oct 2017 04:04:07 +0000 (21:04 -0700)]
nfp: bpf: encode all 64bit shifts
Add encodings of all 64bit shift operations.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 9 Oct 2017 04:04:06 +0000 (21:04 -0700)]
nfp: bpf: move software reg helpers and cmd table out of translator
Move the software reg helpers and some static data to nfp_asm.c.
They are related to the previous patch, but move is done in a separate
commit for ease of review.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 9 Oct 2017 04:04:05 +0000 (21:04 -0700)]
nfp: bpf: use the power of sparse to check we encode registers right
Define a new __bitwise type for software representation of registers.
This will allow us to catch incorrect parameter types using sparse.
Accessors we define also allow us to return correct enum type and
therefore ensure all switches handle all register types.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 9 Oct 2017 04:04:04 +0000 (21:04 -0700)]
nfp: bpf: lift the single-port limitation
Limiting the eBPF offload to a single port was a workaround
required for the PoC application FW which has not been
released externally. It's not necessary any more.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Mon, 9 Oct 2017 04:04:03 +0000 (21:04 -0700)]
nfp: output control messages to trace_devlink_hwmsg()
Use standard devlink trace point to allow tracing of control
messages.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 9 Oct 2017 16:46:54 +0000 (09:46 -0700)]
Merge branch 'hns3-cleanups'
Yunsheng Lin says:
====================
A few cleanup for hns3 ethernet driver
This patchset contains a few cleanup for hns3 ethernet driver.
No functional change intended.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Yunsheng Lin [Mon, 9 Oct 2017 07:44:01 +0000 (15:44 +0800)]
net: hns3: Cleanup for non-static function in hns3 driver
This patch fixes the following warning from sparse:
warning: symbol 'hns3_set_multicast_list' was not declared.
Should it be static.
hns3_set_multicast_list turns out to be not used, so delete it.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yunsheng Lin [Mon, 9 Oct 2017 07:44:00 +0000 (15:44 +0800)]
net: hns3: Cleanup for endian issue in hns3 driver
This patch fixes a lot of endian issues detected by sparse.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yunsheng Lin [Mon, 9 Oct 2017 07:43:59 +0000 (15:43 +0800)]
net: hns3: Cleanup for struct that used to send cmd to firmware
The hclge_tm module has already added _cmd to the end of struct
that used to send cmd to firmware. This will help us finding the
endian issues.
This patch adds the _cmd to the end of struct that used to send
cmd to firmware in hclge_main module.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yunsheng Lin [Mon, 9 Oct 2017 07:43:58 +0000 (15:43 +0800)]
net: hns3: Consistently using GENMASK in hns3 driver
This patch uses GENMASK to generate bit mask whenever
possible in hns3 driver.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yunsheng Lin [Mon, 9 Oct 2017 07:43:57 +0000 (15:43 +0800)]
net: hns3: Cleanup indentation for Kconfig in the the hisilicon folder
This patch fixes a few indentation for Kconfig file in the
hisilicon folder.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yunsheng Lin [Mon, 9 Oct 2017 07:43:56 +0000 (15:43 +0800)]
net: hns3: Add hns3_get_handle macro in hns3 driver
There are many places that will need to get the handle
of netdev, so add a macro to get the handle of netdev.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yunsheng Lin [Mon, 9 Oct 2017 07:43:55 +0000 (15:43 +0800)]
net: hns3: Cleanup for shifting true in hns3 driver
This patch fixes a shifting true in hclge_main module.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Emil Tantilov [Tue, 29 Aug 2017 19:21:48 +0000 (12:21 -0700)]
ixgbe: split Tx/Rx ring clearing for ethtool loopback test
Commit:
fed21bcee7a5
("ixgbe: Don't bother clearing buffer memory for descriptor rings)
exposed some issues with the logic in the current implementation of
ixgbe_clean_test_rings() that are being addressed in this patch:
- Split the clearing of the Tx and Rx rings in separate loops. Previously
both Tx and Rx rings were cleared in a rx_desc->wb.upper.length based
loop which could lead to issues if for w/e reason packets were received
outside of the frames transmitted for the loopback test.
- Add check for IXGBE_TXD_STAT_DD to avoid clearing the rings if the
transmits have not comlpeted by the time we enter ixgbe_clean_test_rings()
- Exit early on ixgbe_check_lbtest_frame() failure.
This change fixes a crash during ethtool diagnostic (ethtool -t).
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Emil Tantilov [Fri, 18 Aug 2017 22:48:02 +0000 (15:48 -0700)]
ixgbe: add error checks when initializing the PHY
Ignoring errors when attempting to identify the PHY can lead to a crash.
Specifically in the case of FW controlled PHYs where the PHY read/write
operations are set to NULL.
Removed redundant comment.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Shannon Nelson [Tue, 15 Aug 2017 15:59:54 +0000 (08:59 -0700)]
ixgbe: restore normal RSS after last macvlan offload is removed
Just like when the last VF is removed, we need to restore normal
operations after the last macvlan offload is removed, else we
get stuck in single queue operations.
To test:
ethtool -l eth1 # note the number of queues in use, ~= cpus
ethtool -K eth1 l2-fwd-offload on
ip link add mv1 link eth1 type macvlan mode bridge
ip link set dev mv1 up
ip link del mv1
ethtool -l eth1 # are we back to the same # of queues, or stuck on 1?
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bhumika Goyal [Mon, 17 Jul 2017 15:01:18 +0000 (20:31 +0530)]
ixgbe: declare ixgbe_mac_operations structures as const
Declare ixgbe_mac_operations structures as const as they are only stored
in the mac_ops field of ixgbe_info structure. This field is of type
const and therefore ixgbe_mac_operations structure can be made const
too.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Emil Tantilov [Wed, 5 Jul 2017 22:57:30 +0000 (15:57 -0700)]
ixgbe: Clear SWFW_SYNC register during init
Added clearing of SW resource bits in the SW/FW synchronization
register to ixgbe_init_swfw_sync_X540().
Updated ixgbe_acquire_swfw_sync_X540 SW Manageability host interface
resource bit error case to match the error handling of the other SW
resource bits. Which is to release the SW resource bits if SW times
out while attempting to acquire the resource.
This allows the driver to load in cases where the semaphore bits
could be stuck after a reset or a crash.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Christos Gkekas [Sun, 8 Oct 2017 22:46:47 +0000 (23:46 +0100)]
qed: Delete redundant check on dcb_app priority
dcb_app priority is unsigned thus checking whether it is less than zero
is redundant.
Signed-off-by: Christos Gkekas <chris.gekas@gmail.com>
Acked-By: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christos Gkekas [Sun, 8 Oct 2017 19:13:49 +0000 (20:13 +0100)]
net: ethernet: stmmac: Clean up dead code
Many macros in dwmac-ipq806x are unused and should be removed.
Moreover gmac->id is an unsigned variable and therefore checking
whether it is less than zero is redundant.
Signed-off-by: Christos Gkekas <chris.gekas@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 9 Oct 2017 04:16:31 +0000 (21:16 -0700)]
Merge branch 'ipv6_dev_get_saddr-rcu'
Eric Dumazet says:
====================
ipv6: ipv6_dev_get_saddr() rcu works
Sending IPv6 udp packets on non connected sockets is quite slow,
because ipv6_dev_get_saddr() is still using an rwlock and silly
references games on ifa.
Tested:
$ ./super_netperf 16 -H 4444::555:0786 -l 2000 -t UDP_STREAM -- -m 100 &
[1] 12527
Performance is boosted from 2.02 Mpps to 4.28 Mpps
Kernel profile before patches :
22.62% [kernel] [k] _raw_read_lock_bh
7.04% [kernel] [k] refcount_sub_and_test
6.56% [kernel] [k] ipv6_get_saddr_eval
5.67% [kernel] [k] _raw_read_unlock_bh
5.34% [kernel] [k] __ipv6_dev_get_saddr
4.95% [kernel] [k] refcount_inc_not_zero
4.03% [kernel] [k] __ip6addrlbl_match
3.70% [kernel] [k] _raw_spin_lock
3.44% [kernel] [k] ipv6_dev_get_saddr
3.24% [kernel] [k] ip6_pol_route
3.06% [kernel] [k] refcount_add_not_zero
2.30% [kernel] [k] __local_bh_enable_ip
1.81% [kernel] [k] mlx4_en_xmit
1.20% [kernel] [k] __ip6_append_data
1.12% [kernel] [k] __ip6_make_skb
1.11% [kernel] [k] __dev_queue_xmit
1.06% [kernel] [k] l3mdev_master_ifindex_rcu
Kernel profile after patches :
11.36% [kernel] [k] ip6_pol_route
7.65% [kernel] [k] _raw_spin_lock
7.16% [kernel] [k] __ipv6_dev_get_saddr
6.49% [kernel] [k] ipv6_get_saddr_eval
6.04% [kernel] [k] refcount_add_not_zero
3.34% [kernel] [k] __ip6addrlbl_match
2.62% [kernel] [k] __dev_queue_xmit
2.37% [kernel] [k] mlx4_en_xmit
2.26% [kernel] [k] dst_release
1.89% [kernel] [k] __ip6_make_skb
1.87% [kernel] [k] __ip6_append_data
1.86% [kernel] [k] udpv6_sendmsg
1.86% [kernel] [k] ip6t_do_table
1.64% [kernel] [k] ipv6_dev_get_saddr
1.64% [kernel] [k] find_match
1.51% [kernel] [k] l3mdev_master_ifindex_rcu
1.24% [kernel] [k] ipv6_addr_label
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sun, 8 Oct 2017 02:30:28 +0000 (19:30 -0700)]
ipv6: avoid cache line dirtying in ipv6_dev_get_saddr()
By extending the rcu section a bit, we can avoid these
very expensive in6_ifa_put()/in6_ifa_hold() calls
done in __ipv6_dev_get_saddr() and ipv6_dev_get_saddr()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sun, 8 Oct 2017 02:30:27 +0000 (19:30 -0700)]
ipv6: __ipv6_dev_get_saddr() rcu conversion
Callers hold rcu_read_lock(), so we do not need
the rcu_read_lock()/rcu_read_unlock() pair.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sun, 8 Oct 2017 02:30:26 +0000 (19:30 -0700)]
ipv6: ipv6_chk_prefix() rcu conversion
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sun, 8 Oct 2017 02:30:25 +0000 (19:30 -0700)]
ipv6: ipv6_chk_custom_prefix() rcu conversion
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sun, 8 Oct 2017 02:30:24 +0000 (19:30 -0700)]
ipv6: ipv6_count_addresses() rcu conversion
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Sun, 8 Oct 2017 02:30:23 +0000 (19:30 -0700)]
ipv6: prepare RCU lookups for idev->addr_list
inet6_ifa_finish_destroy() already uses kfree_rcu() to free
inet6_ifaddr structs.
We need to use proper list additions/deletions in order
to allow readers to use RCU instead of idev->lock rwlock.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 9 Oct 2017 04:12:04 +0000 (21:12 -0700)]
Merge branch 'bridge-neigh-msg-proxy-and-flood-suppression-support'
Roopa Prabhu says:
====================
bridge: neigh msg proxy and flood suppression support
This series implements arp and nd suppression in the bridge
driver for ethernet vpns. It implements rfc7432, section 10
https://tools.ietf.org/html/rfc7432#section-10
for ethernet VPN deployments. It is similar to the existing
BR_PROXYARP* flags but has a few semantic differences to conform
to EVPN standard. Unlike the existing flags, this new flag suppresses
flood of all neigh discovery packets (arp and nd) to tunnel ports.
Supports both vlan filtering and non-vlan filtering bridges.
In case of EVPN, it is mainly used to avoid flooding
of arp and nd packets to tunnel ports like vxlan.
v2 : rebase to latest + address some optimization feedback from Nikolay.
v3 : fix kbuild reported build errors with CONFIG_INET off
v4 : simplify port flag mask as suggested by stephen
v5 : address some feedback from Toshiaki
v6 : some v5 cleanups in nd suppress (keep it consistent with arp suppress)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Roopa Prabhu [Sat, 7 Oct 2017 05:12:39 +0000 (22:12 -0700)]
bridge: suppress nd pkts on BR_NEIGH_SUPPRESS ports
This patch avoids flooding and proxies ndisc packets
for BR_NEIGH_SUPPRESS ports.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Roopa Prabhu [Sat, 7 Oct 2017 05:12:38 +0000 (22:12 -0700)]
bridge: suppress arp pkts on BR_NEIGH_SUPPRESS ports
This patch avoids flooding and proxies arp packets
for BR_NEIGH_SUPPRESS ports.
Moves existing br_do_proxy_arp to br_do_proxy_suppress_arp
to support both proxy arp and neigh suppress.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Roopa Prabhu [Sat, 7 Oct 2017 05:12:37 +0000 (22:12 -0700)]
bridge: add new BR_NEIGH_SUPPRESS port flag to suppress arp and nd flood
This patch adds a new bridge port flag BR_NEIGH_SUPPRESS to
suppress arp and nd flood on bridge ports. It implements
rfc7432, section 10.
https://tools.ietf.org/html/rfc7432#section-10
for ethernet VPN deployments. It is similar to the existing
BR_PROXYARP* flags but has a few semantic differences to conform
to EVPN standard. Unlike the existing flags, this new flag suppresses
flood of all neigh discovery packets (arp and nd) to tunnel ports.
Supports both vlan filtering and non-vlan filtering bridges.
In case of EVPN, it is mainly used to avoid flooding
of arp and nd packets to tunnel ports like vxlan.
This patch adds netlink and sysfs support to set this bridge port
flag.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 9 Oct 2017 04:07:18 +0000 (21:07 -0700)]
ipv6: fix a BUG in rt6_get_pcpu_route()
Ido reported following splat and provided a patch.
[ 122.221814] BUG: using smp_processor_id() in preemptible [
00000000] code: sshd/2672
[ 122.221845] caller is debug_smp_processor_id+0x17/0x20
[ 122.221866] CPU: 0 PID: 2672 Comm: sshd Not tainted 4.14.0-rc3-idosch-next-custom #639
[ 122.221880] Hardware name: Mellanox Technologies Ltd. MSN2100-CB2FO/SA001017, BIOS 5.6.5 06/07/2016
[ 122.221893] Call Trace:
[ 122.221919] dump_stack+0xb1/0x10c
[ 122.221946] ? _atomic_dec_and_lock+0x124/0x124
[ 122.221974] ? ___ratelimit+0xfe/0x240
[ 122.222020] check_preemption_disabled+0x173/0x1b0
[ 122.222060] debug_smp_processor_id+0x17/0x20
[ 122.222083] ip6_pol_route+0x1482/0x24a0
...
I believe we can simplify this code path a bit, since we no longer
hold a read_lock and need to release it to avoid a dead lock.
By disabling BH, we make sure we'll prevent code re-entry and
rt6_get_pcpu_route()/rt6_make_pcpu_route() run on the same cpu.
Fixes:
66f5d6ce53e6 ("ipv6: replace rwlock with rcu and spinlock in fib6_table")
Reported-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 9 Oct 2017 04:07:11 +0000 (21:07 -0700)]
Merge tag 'mlx5-updates-2017-10-06' of git://git./linux/kernel/git/mellanox/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 updates 2017-10-06
This series includes some shared code updates for kernel 4.15 to both
net-next and rdma-next trees.
The series includes mlx5 low level flow steering updates and optimizations
to support firmware command parallelism for flow steering requests from
Maor Gottlieb and two other small fixes from Matan and Maor.
One fix from Matan adds error handling for when the destination
list of the flow steering rule is full.
Maor introduced a patch to avoid NULL pointer dereference on steering cleanup.
Then Some refactoring patches needed by the series for code sharing purposes.
and split the Flow Table Entry (FTE) and Flow Group (FG) creation code to two parts:
1) Object allocation - allocate the steering node and initialize
its resources.
2) The firmware command execution.
This change will give us the ability to take write lock on the
parent node (e.g. FG for FTE creating) only on the software data struct allocation
and creation part of the procedure where the synchronization is really required,
and will allow us to execute multiple firmware commands simultaneously and overcome the
firmware bottleneck.
Refactor the locking scheme of the mlx5 core flow steering as follows:
1) Replace the mutex lock with readers-writers semaphore and take
the write lock only when necessary (e.g. allocating a new flow
table entry index or adding a node to the parent's children list).
When we try to find a suitable child in the parent's children list
(e.g. search for flow group with the same match_criteria of the rule)
then we only take the read lock.
2) Add versioning mechanism - each steering entity (FT, FG, FTE, DST)
will have an incremental version. The version is increased when the
entity is changed (e.g. when a new FTE was added to FG - the FG's
version is increased).
Versioning is used in order to determine if the last traverse of an
entity's children is valid or a rescan under write lock is required.
Last patch adds FGs and FTEs memory pool, It is useful because these objects
are not small and could be allocated/deallocated many times.
This support improves the insertion rate of steering rules
from ~5k/sec to ~40k/sec.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 8 Oct 2017 17:11:01 +0000 (10:11 -0700)]
Merge branch 'hv_netvsc-TCP-hash-level'
Haiyang Zhang says:
====================
hv_netvsc: support changing TCP hash level
The patch set simplifies the existing hash level switching code for
UDP. It also adds the support for changing TCP hash level. So users
can switch between L3 an L4 hash levels for TCP and UDP.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Haiyang Zhang [Fri, 6 Oct 2017 15:33:59 +0000 (08:33 -0700)]
hv_netvsc: Update netvsc Document for TCP hash level setting
Update Documentation/networking/netvsc.txt for TCP hash level setting
and related info.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Haiyang Zhang [Fri, 6 Oct 2017 15:33:58 +0000 (08:33 -0700)]
hv_netvsc: Add ethtool handler to set and get TCP hash levels
The patch supports the options to switch TCP hash level between
L3 and L4 by ethtool command. TCP over IPv4 and v6 can be set
differently. The default hash level is L4. We currently only
allow switching TX hash level from within the guests.
For example, for TCP over IPv4 on eth0:
To include TCP port numbers in hashing:
ethtool -N eth0 rx-flow-hash tcp4 sdfn
To exclude TCP port numbers in hashing:
ethtool -N eth0 rx-flow-hash tcp4 sd
To show TCP hash level:
ethtool -n eth0 rx-flow-hash tcp4
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Haiyang Zhang [Fri, 6 Oct 2017 15:33:57 +0000 (08:33 -0700)]
hv_netvsc: Change the hash level variable to bit flags
This simplifies the logic and make it easier to add more
options.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 8 Oct 2017 17:07:21 +0000 (10:07 -0700)]
Merge branch 'mlxsw-more-extack'
Jiri Pirko says:
====================
mlxsw: Add more extack error reporting
Ido says:
Add error messages to VLAN and bridge enslavements to help users
understand why the enslavement failed.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Sun, 8 Oct 2017 09:57:56 +0000 (11:57 +0200)]
mlxsw: spectrum: Propagate extack further for bridge enslavements
The code that actually takes care of bridge offload introduces a few
more non-trivial constraints with regards to bridge enslavements.
Propagate extack there to indicate the reason.
$ ip link add link enp1s0np1 name enp1s0np1.10 type vlan id 10
$ ip link add link enp1s0np1 name enp1s0np1.20 type vlan id 20
$ ip link add name br0 type bridge
$ ip link set dev enp1s0np1.10 master br0
$ ip link set dev enp1s0np1.20 master br0
Error: spectrum: Can not bridge VLAN uppers of the same port.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Sun, 8 Oct 2017 09:57:55 +0000 (11:57 +0200)]
mlxsw: spectrum: Add extack for VLAN enslavements
Similar to physical ports, enslavement of VLAN devices can also fail.
Use extack to indicate why the enslavement failed.
$ ip link add link enp1s0np1 name enp1s0np1.10 type vlan id 10
$ ip link add name bond0 type bond mode 802.3ad
$ ip link set dev enp1s0np1.10 master bond0
Error: spectrum: VLAN devices only support bridge and VRF uppers.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 7 Oct 2017 22:29:40 +0000 (23:29 +0100)]
Merge branch 'bpf-obj-name-misc'
Martin KaFai Lau says:
====================
bpf: Misc improvements and a new usage on bpf obj name
The first two patches make improvements on the bpf obj name.
The last patch adds the prog name to kallsyms.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Martin KaFai Lau [Fri, 6 Oct 2017 04:52:13 +0000 (21:52 -0700)]
bpf: Append prog->aux->name in bpf_get_prog_name()
This patch makes the bpf_prog's name available
in kallsyms.
The new format is bpf_prog_tag[_name].
Sample kallsyms from running selftests/bpf/test_progs:
[root@arch-fb-vm1 ~]# egrep ' bpf_prog_[0-9a-fA-F]{16}' /proc/kallsyms
ffffffffa0048000 t bpf_prog_dabf0207d1992486_test_obj_id
ffffffffa0038000 t bpf_prog_a04f5eef06a7f555__123456789ABCDE
ffffffffa0050000 t bpf_prog_a04f5eef06a7f555
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Martin KaFai Lau [Fri, 6 Oct 2017 04:52:12 +0000 (21:52 -0700)]
bpf: Use char in prog and map name
Instead of u8, use char for prog and map name. It can avoid the
userspace tool getting compiler's signess warning. The
bpf_prog_aux, bpf_map, bpf_attr, bpf_prog_info and
bpf_map_info are changed.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Martin KaFai Lau [Fri, 6 Oct 2017 04:52:11 +0000 (21:52 -0700)]
bpf: Change bpf_obj_name_cpy() to better ensure map's name is init by 0
During get_info_by_fd, the prog/map name is memcpy-ed. It depends
on the prog->aux->name and map->name to be zero initialized.
bpf_prog_aux is easy to guarantee that aux->name is zero init.
The name in bpf_map may be harder to be guaranteed in the future when
new map type is added.
Hence, this patch makes bpf_obj_name_cpy() to always zero init
the prog/map name.
Suggested-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
William Tu [Thu, 5 Oct 2017 19:07:12 +0000 (12:07 -0700)]
ip_gre: check packet length and mtu correctly in erspan tx
Similarly to early patch for erspan_xmit(), the ARPHDR_ETHER device
is the length of the whole ether packet. So skb->len should subtract
the dev->hard_header_len.
Fixes:
1a66a836da63 ("gre: add collect_md mode to ERSPAN tunnel")
Fixes:
84e54fe0a5ea ("gre: introduce native tunnel support for ERSPAN")
Signed-off-by: William Tu <u9012063@gmail.com>
Cc: Xin Long <lucien.xin@gmail.com>
Cc: David Laight <David.Laight@aculab.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lin Zhang [Thu, 5 Oct 2017 17:40:35 +0000 (01:40 +0800)]
net: phonet: mark phonet_protocol as const
The phonet_protocol structs don't need to be written by anyone and
so can be marked as const.
Signed-off-by: Lin Zhang <xiaolou4617@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lin Zhang [Thu, 5 Oct 2017 17:37:29 +0000 (01:37 +0800)]
net: phonet: mark header_ops as const
Signed-off-by: Lin Zhang <xiaolou4617@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 7 Oct 2017 22:05:58 +0000 (23:05 +0100)]
Merge branch 'bpf-perf-time-helpers'
Yonghong Song says:
====================
bpf: add two helpers to read perf event enabled/running time
Hardware pmu counters are limited resources. When there are more
pmu based perf events opened than available counters, kernel will
multiplex these events so each event gets certain percentage
(but not 100%) of the pmu time. In case that multiplexing happens,
the number of samples or counter value will not reflect the
case compared to no multiplexing. This makes comparison between
different runs difficult.
Typically, the number of samples or counter value should be
normalized before comparing to other experiments. The typical
normalization is done like:
normalized_num_samples = num_samples * time_enabled / time_running
normalized_counter_value = counter_value * time_enabled / time_running
where time_enabled is the time enabled for event and time_running is
the time running for event since last normalization.
This patch set implements two helper functions.
The helper bpf_perf_event_read_value reads counter/time_enabled/time_running
for perf event array map. The helper bpf_perf_prog_read_value read
counter/time_enabled/time_running for bpf prog with type BPF_PROG_TYPE_PERF_EVENT.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Yonghong Song [Thu, 5 Oct 2017 16:19:23 +0000 (09:19 -0700)]
bpf: add a test case for helper bpf_perf_prog_read_value
The bpf sample program trace_event is enhanced to use the new
helper to print out enabled/running time.
Signed-off-by: Yonghong Song <yhs@fb.com>
Acked-by: Alexei Starovoitov <ast@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yonghong Song [Thu, 5 Oct 2017 16:19:22 +0000 (09:19 -0700)]
bpf: add helper bpf_perf_prog_read_value
This patch adds helper bpf_perf_prog_read_cvalue for perf event based bpf
programs, to read event counter and enabled/running time.
The enabled/running time is accumulated since the perf event open.
The typical use case for perf event based bpf program is to attach itself
to a single event. In such cases, if it is desirable to get scaling factor
between two bpf invocations, users can can save the time values in a map,
and use the value from the map and the current value to calculate
the scaling factor.
Signed-off-by: Yonghong Song <yhs@fb.com>
Acked-by: Alexei Starovoitov <ast@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yonghong Song [Thu, 5 Oct 2017 16:19:21 +0000 (09:19 -0700)]
bpf: add a test case for helper bpf_perf_event_read_value
The bpf sample program tracex6 is enhanced to use the new
helper to read enabled/running time as well.
Signed-off-by: Yonghong Song <yhs@fb.com>
Acked-by: Alexei Starovoitov <ast@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yonghong Song [Thu, 5 Oct 2017 16:19:20 +0000 (09:19 -0700)]
bpf: add helper bpf_perf_event_read_value for perf event array map
Hardware pmu counters are limited resources. When there are more
pmu based perf events opened than available counters, kernel will
multiplex these events so each event gets certain percentage
(but not 100%) of the pmu time. In case that multiplexing happens,
the number of samples or counter value will not reflect the
case compared to no multiplexing. This makes comparison between
different runs difficult.
Typically, the number of samples or counter value should be
normalized before comparing to other experiments. The typical
normalization is done like:
normalized_num_samples = num_samples * time_enabled / time_running
normalized_counter_value = counter_value * time_enabled / time_running
where time_enabled is the time enabled for event and time_running is
the time running for event since last normalization.
This patch adds helper bpf_perf_event_read_value for kprobed based perf
event array map, to read perf counter and enabled/running time.
The enabled/running time is accumulated since the perf event open.
To achieve scaling factor between two bpf invocations, users
can can use cpu_id as the key (which is typical for perf array usage model)
to remember the previous value and do the calculation inside the
bpf program.
Signed-off-by: Yonghong Song <yhs@fb.com>
Acked-by: Alexei Starovoitov <ast@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yonghong Song [Thu, 5 Oct 2017 16:19:19 +0000 (09:19 -0700)]
bpf: perf event change needed for subsequent bpf helpers
This patch does not impact existing functionalities.
It contains the changes in perf event area needed for
subsequent bpf_perf_event_read_value and
bpf_perf_prog_read_value helpers.
Signed-off-by: Yonghong Song <yhs@fb.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amine Kherbouche [Wed, 4 Oct 2017 17:35:57 +0000 (19:35 +0200)]
ip_tunnel: add mpls over gre support
This commit introduces the MPLSoGRE support (RFC 4023), using ip tunnel
API by simply adding ipgre_tunnel_encap_(add|del)_mpls_ops() and the new
tunnel type TUNNEL_ENCAP_MPLS.
Signed-off-by: Amine Kherbouche <amine.kherbouche@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 7 Oct 2017 20:22:59 +0000 (21:22 +0100)]
Merge branch 'fib6-rcu'
Wei Wang says:
====================
ipv6: replace rwlock with rcu and spinlock in fib6 table
Currently, fib6 table is protected by rwlock. During route lookup,
reader lock is taken and during route insertion, deletion or
modification, writer lock is taken. This is a very inefficient
implementation because the fastpath always has to do the operation
to grab the reader lock.
According to my latest syn flood test on an iota ivybridage machine
with 2 10G mlx nics bonded together, each with 8 rx queues on 2 NUMA
nodes, and with the upstream net-next kernel:
ipv4 stack can handle around 4.2Mpps
ipv6 stack can handle around 1.3Mpps
In order to close the gap of the performance number between ipv4
and ipv6 stack, this patch series tries to get rid of the usage of
the rwlock and replace it with rcu and spinlock protection. This will
greatly speed up the fastpath performance as it only needs to hold
rcu which is much less expensive than grabbing the reader lock. It
also makes ipv6 fib implementation more consistent with ipv4.
In order to be able to replace the current rwlock with rcu and
spinlock, some preparation work is needed:
Patch 1-8 introduces a per-route hash table (protected by rcu and a
different spinlock) to store all cached routes created by pmtu and ip
redirect under its main route. This makes the main fib6 tree only
contain static routes.
Patch 9-14 prepares all the reader path to be ready to tolerate
concurrent writer.
Patch 15 finally does the rwlock to rcu and spinlock conversion.
Patch 16 takes care of rt6_stats.
After this patch series, in the same syn flood test,
ipv6 stack can now handle around 3.5Mpps compared to previous 1.3Mpps
in my test setup.
After this patch series, there are still some improvements that should
be done in ipv6 stack:
1. During route lookup, dst_use() is called everytime on the selected
route to update dst->__use and dst->lastuse. This dirties the cacheline
and causes extra cacheline miss and should be avoided.
2. when no route is found in the current table, net->ip6.ipv6_null_entry
is used and refcnt is taken on it. As there is no pcpu cache for this
specific route, frequent change on the refcnt for this route causes
quite some cacheline misses.
And to make things worse, if CONFIG_IPV6_MULTIPLE_TABLES is defined,
output path route lookup always starts with local table first and
guarantees to hit net->ipv6.ip6_null_entry before continuing to do
lookup in the main table.
These operations on net->ipv6.ip6_null_entry could potentially be
avoided.
3. ipv6 input path route lookup grabs refcnt on dst. This is different
from ipv4. We could potentially change this behavior to let ipv6 input
path route lookup not to grab refcnt on dst. However, it does not give
us much performance boost as we currently have pcpu route cache for
input path as well in ipv6. But this work probably is still worth doing
to unify ipv6 and ipv4 route lookup behavior.
The above issues will be addressed separately after this patch series
has been accepted.
This is a joint work with Martin KaFai Lau and Eric Dumazet. And many
many thanks to them for their inspiring ideas and big big code review
efforts.
====================
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>