OSDN Git Service
Peter De Schrijver [Tue, 25 Jul 2017 10:34:03 +0000 (13:34 +0300)]
clk: tegra: Enable PLL_SS for Tegra210
Make sure the pll_ss ops are compiled even when only building for Tegra210.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Shreshtha Sahu <ssahu@nvidia.com>
Tested-by: Shreshtha Sahu <ssahu@nvidia.com>
Reviewed-by: Jon Mayo <jmayo@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Peter De Schrijver [Tue, 25 Jul 2017 10:34:02 +0000 (13:34 +0300)]
clk: tegra: fix SS control on PLL enable/disable
PLL SS was only controlled when setting the PLL rate, not when the PLL itself
is enabled or disabled.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Jon Mayo <jmayo@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Georgi Djakov [Fri, 18 Aug 2017 14:22:50 +0000 (17:22 +0300)]
clk: qcom: msm8916: Fix bimc gpu clock ops
The clock bimc_gpu_clk_src is incorrectly set to use the shared rcg2
ops, which are for RCGs with child branches controlled by different
CPUs.
The result of the incorrect ops is that the GPU's PM runtime may leave
this clock set at a very low rate. Fix this issue by using the correct
rcg2 ops.
Fixes:
a2e8272f3f89 ("clk: qcom: Add MSM8916 gpu clocks")
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Bhumika Goyal [Tue, 22 Aug 2017 13:11:15 +0000 (18:41 +0530)]
clk: ti: make clk_ops const
Make these const as they are only stored in the const field of a
clk_init_data structure.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Stephen Boyd [Wed, 23 Aug 2017 22:39:58 +0000 (15:39 -0700)]
Merge tag 'clk-renesas-for-v4.14-tag1' of git://git./linux/kernel/git/geert/renesas-drivers into clk-next
Pull Renesas clk driver updates from Geert Uytterhoeven:
* Add more module clocks for R-Car V2H and M3-W,
* Add support for the R-Car Gen3 USB 2.0 clock selector PHY,
* Add support for the new R-Car D3 SoC,
* Allow compile-testing of all (sub)drivers now all dummy infrastructure
is available,
* Small fixes and cleanups.
* tag 'clk-renesas-for-v4.14-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers:
clk: renesas: r8a7796: Add USB3.0 clock
clk: renesas: rcar-usb2-clock-sel: Add R-Car USB 2.0 clock selector PHY
clk: renesas: cpg-mssr: Add R8A77995 support
clk: renesas: rcar-gen3: Add support for SCCG/Clean peripheral clocks
clk: renesas: rcar-gen3: Add divider support for PLL1 and PLL3
clk: renesas: Add r8a77995 CPG Core Clock Definitions
clk: renesas: rcar-gen3-cpg: Refactor checks for accessing the div table
clk: renesas: rcar-gen3-cpg: Drop superfluous variable
clk: renesas: Allow compile-testing of all (sub)drivers
clk: renesas: r8a7792: Add IMR-LX3/LSX3 clocks
clk: renesas: div6: Document fields used for parent selection
Stephen Boyd [Wed, 23 Aug 2017 22:35:41 +0000 (15:35 -0700)]
clk: rockchip: Mark rockchip_fractional_approximation static
Silence the sparse warning
clk/rockchip/clk.c:172:6: warning: symbol 'rockchip_fractional_approximation' was not declared. Should it be static?
Cc: Elaine Zhang <zhangqing@rock-chips.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Stephen Boyd [Wed, 23 Aug 2017 22:33:45 +0000 (15:33 -0700)]
Merge tag 'v4.14-rockchip-clk1' of git://git./linux/kernel/git/mmind/linux-rockchip into clk-next
Pull Rockchip clk driver updates from Heiko Stuebner:
The biggest change is fixing the jitter on the fractional clock-type
Rockchip socs experience with the default approximation. For that we
introduce the ability to override it with a clock-specific approximation
and use that to create the needed rate settings as described in the
Rockchip soc manuals (same for all Rockchip socs).
Apart from that we have support for the rk3126 clock controller
which is similar to the rk3128 with some minimal differences
and a lot of improvements and fixes for the rv1108 clock controller
(missing clocks, some clock-ids, naming fixes, register fixes).
* tag 'v4.14-rockchip-clk1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
clk: rockchip: fix the rv1108 clk_mac sel register description
clk: rockchip: rename rv1108 macphy clock to mac
clk: rockchip: add rv1108 ACLK_GMAC and PCLK_GMAC clocks
clk: rockchip: add rk3228 SCLK_SDIO_SRC clk id
clk: rockchip: add rv1108 ACLK_GAMC and PCLK_GMAC ID
clk: rockchip: add rk3228 sclk_sdio_src ID
clk: rockchip: add special approximation to fix up fractional clk's jitter
clk: fractional-divider: allow overriding of approximation
clk: rockchip: modify rk3128 clk driver to also support rk3126
dt-bindings: add documentation for rk3126 clock
clk: rockchip: add some critical clocks for rv1108 SoC
clk: rockchip: rename some of clks for rv1108 SoC
clk: rockchip: fix up some clks describe error for rv1108 SoC
clk: rockchip: support more clks for rv1108
clk: rockchip: fix up the pll clks error for rv1108 SoC
clk: rockchip: support more rates for rv1108 cpuclk
clk: rockchip: fix up indentation of some RV1108 clock-ids
clk: rockchip: rename the clk id for HCLK_I2S1_2CH
clk: rockchip: add more clk ids for rv1108
Stephen Boyd [Wed, 23 Aug 2017 22:31:48 +0000 (15:31 -0700)]
Merge tag 'sunxi-clk-for-4.14-2' of https://git./linux/kernel/git/sunxi/linux into clk-next
Pull Allwinner clock changes from Chen-Yu Tsai:
* Added support for fixed post-divider on divider and NKM-style clocks
* Added driver for R40 CCU
* Fix sunxi-ng/ccu-sunxi-r.h header file guard macro typo
* Make fractional clock modes really used and correctly configured
* Make H3 cpu clock rate change correctly to be used with cpufreq
* tag 'sunxi-clk-for-4.14-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
clk: sunxi-ng: support R40 SoC
dt-bindings: add compatible string for Allwinner R40 CCU
clk: sunxi-ng: nkm: add support for fixed post-divider
clk: sunxi-ng: div: Add support for fixed post-divider
dt-bindings: clock: sunxi-ccu: Add compatibles for sun5i CCU driver
clk: sunxi-ng: allow set parent clock (PLL_CPUX) for CPUX clock on H3
clk: sunxi-ng: h3: gate then ungate PLL CPU clk after rate change
clk: sunxi-ng: Wait for lock when using fractional mode
clk: sunxi-ng: Make fractional helper less chatty
clk: sunxi-ng: multiplier: Fix fractional mode
clk: sunxi-ng: Fix fractional mode for N-M clocks
clk: sunxi-ng: Fix header guard of ccu-sun8i-r.h
Stephen Boyd [Wed, 23 Aug 2017 22:30:29 +0000 (15:30 -0700)]
Merge tag 'clk-v4.14-samsung' of git://git./linux/kernel/git/snawrocki/clk into clk-next
Pull Samsung clk driver updates from Sylwester Nawrocki:
Changes in definitions of audio related clocks for Exynos5420/5422/5800
SoCs: a fix of mau_epll clock definition and changes enabling clock rate
setting propagation on a path from the I2S IP block up the EPLL.
* tag 'clk-v4.14-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/snawrocki/clk:
clk: samsung: exynos542x: Enable clock rate propagation up to the EPLL
clk: samsung: Add CLK_SET_RATE_PARENT to some AUDSS CLK CON clocks
clk: samsung: Fix mau_epll clock definition for exynos5422
Stephen Boyd [Wed, 23 Aug 2017 22:28:52 +0000 (15:28 -0700)]
Merge tag 'meson-clk-for-4.14' of git://github.com/baylibre/clk-meson into clk-next
Pull Amlogic clock driver updates from Neil Armstrong:
* meson8b: add the reset controller to the clkc
* meson: expose all clk ids
* gxbb-aoclk: Add CEC 32k clock
* gxbb: add mmc input 0 clocks
* meson: fix protection against undefined clks
* gxbb: fix audio divider flags
* tag 'meson-clk-for-4.14' of git://github.com/baylibre/clk-meson:
clk: meson: gxbb-aoclk: Add CEC 32k clock
clk: meson: gxbb-aoclk: Switch to regmap for register access
dt-bindings: clock: amlogic, gxbb-aoclkc: Update bindings
clk: meson: gxbb: Add sd_emmc clk0 clocks
clk: meson: gxbb: fix clk_mclk_i958 divider flags
clk: meson: gxbb: fix meson cts_amclk divider flags
clk: meson: meson8b: register the built-in reset controller
dt-bindings: clock: gxbb-aoclk: Add CEC 32k clock
clk: meson: gxbb: Add sd_emmc clk0 clkids
clk: meson-gxbb: expose almost every clock in the bindings
clk: meson8b: expose every clock in the bindings
clk: meson: gxbb: fix protection against undefined clks
clk: meson: meson8b: fix protection against undefined clks
dt-bindings: clock: meson8b: describe the embedded reset controller
Elaine Zhang [Mon, 21 Aug 2017 08:16:07 +0000 (16:16 +0800)]
clk: rockchip: fix the rv1108 clk_mac sel register description
The source clock ordering is wrong, as shown in the TRM:
cru_sel24_con[8]
rmii_extclk_sel
clock source select control register
1'b0: from internal PLL
1'b1: from external IO
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Elaine Zhang [Mon, 21 Aug 2017 08:16:06 +0000 (16:16 +0800)]
clk: rockchip: rename rv1108 macphy clock to mac
This MAC has no internal phy for rv1108 and the whole clock
infrastructure hasn't been used yet, so is safe to fix.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Elaine Zhang [Mon, 21 Aug 2017 08:16:05 +0000 (16:16 +0800)]
clk: rockchip: add rv1108 ACLK_GMAC and PCLK_GMAC clocks
Add gmac aclk and pclk clock gates.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Elaine Zhang [Fri, 18 Aug 2017 03:49:25 +0000 (11:49 +0800)]
clk: rockchip: add rk3228 SCLK_SDIO_SRC clk id
In some special circumstances, may be need to reparent clk for sclk_sdio_src.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Heiko Stuebner [Mon, 21 Aug 2017 22:39:00 +0000 (00:39 +0200)]
Merge branch 'v4.14-shared/clkids' into v4.14-clk/next
Elaine Zhang [Mon, 21 Aug 2017 08:16:04 +0000 (16:16 +0800)]
clk: rockchip: add rv1108 ACLK_GAMC and PCLK_GMAC ID
This patch exports gmac aclk and pclk for dts reference.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Elaine Zhang [Fri, 18 Aug 2017 03:49:24 +0000 (11:49 +0800)]
clk: rockchip: add rk3228 sclk_sdio_src ID
This patch exports sdio src clock for dts reference.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Icenowy Zheng [Tue, 15 Aug 2017 05:55:29 +0000 (13:55 +0800)]
clk: sunxi-ng: support R40 SoC
Allwinner R40 SoC have a clock controller module in the style of the
SoCs beyond sun6i, however, it's more rich and complex.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Icenowy Zheng [Sat, 27 May 2017 10:23:05 +0000 (18:23 +0800)]
dt-bindings: add compatible string for Allwinner R40 CCU
Allwinner R40 has a clock controlling unit like the ones on other
Allwinner SoCs after sun6i, and can also use a CCU-based driver.
Add a compatible string for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Hiromitsu Yamasaki [Wed, 26 Jul 2017 11:23:39 +0000 (20:23 +0900)]
clk: renesas: r8a7796: Add USB3.0 clock
This patch adds USB3.0-IF0 clock for R8A7796 SoC.
Signed-off-by: Hiromitsu Yamasaki <hiromitsu.yamasaki.ym@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Yoshihiro Shimoda [Tue, 25 Jul 2017 06:26:27 +0000 (15:26 +0900)]
clk: renesas: rcar-usb2-clock-sel: Add R-Car USB 2.0 clock selector PHY
R-Car USB 2.0 controller can change the clock source from an oscillator
to an external clock via a register. So, this patch adds support
the clock source selector as a clock driver.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Geert Uytterhoeven [Wed, 12 Jul 2017 08:47:36 +0000 (10:47 +0200)]
clk: renesas: cpg-mssr: Add R8A77995 support
Add R-Car D3 (R8A77995) Clock Pulse Generator / Module Standby and
Software Reset support, using the CPG/MSSR driver core and the common
R-Car Gen3 CPG code.
Based on the R-Car Series, 3rd Generation Hardware User's Manual, Rev.
0.55, Jun. 30, 2017.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Rob Herring <robh@kernel.org>
Geert Uytterhoeven [Wed, 19 Jul 2017 15:39:54 +0000 (17:39 +0200)]
clk: renesas: rcar-gen3: Add support for SCCG/Clean peripheral clocks
On R-Car Gen3 SoCs with a Spread Spectrum Clock Generator (e.g. R-Car
D3), a peripheral clock divider has been added, to select between clean
and spread spectrum parents.
Add a new clock type to the R-Car Gen3 driver core to handle this.
To avoid increasing the size of struct cpg_core_clk, both parents and
dividers are stored in the existing parent resp. div fields.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Geert Uytterhoeven [Wed, 19 Jul 2017 14:30:45 +0000 (16:30 +0200)]
clk: renesas: rcar-gen3: Add divider support for PLL1 and PLL3
On some R-Car Gen3 SoCs (e.g. R-Car D3), PLL1 and PLL3 use a divider
value different from one. Extend struct rcar_gen3_cpg_pll_config to handle
this. As all multipliers and dividers are small, table size increase
can be kept limited by storing them in u8s instead of unsigned ints,
which saves ca. 0.5 KiB for a generic kernel.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Geert Uytterhoeven [Tue, 11 Jul 2017 14:58:42 +0000 (16:58 +0200)]
clk: renesas: Add r8a77995 CPG Core Clock Definitions
Add all R-Car D3 Clock Pulse Generator Core Clock Outputs, as listed
in Table 8.2f ("List of Clocks [R-Car D3]") of the R-Car Series, 3rd
Generation Hardware User's Manual (Rev. 0.55, Jun. 30, 2017).
Note that internal CPG clocks (S0, S1, S2, S3, S1C, S3C, SDSRC, and
SSPSRC) are not included, as they are used as internal clock sources
only, and never referenced from DT.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Icenowy Zheng [Sat, 12 Aug 2017 12:43:51 +0000 (20:43 +0800)]
clk: sunxi-ng: nkm: add support for fixed post-divider
SATA PLL on Allwinner R40 is of type (parent) * N * K / M / 6 where 6 is
the fixed post-divider.
Add post-divider support for NKM type clock.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
[wens@csie.org: Fixed application of post-divider in set_rate callback]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Priit Laes [Sat, 12 Aug 2017 12:43:50 +0000 (20:43 +0800)]
clk: sunxi-ng: div: Add support for fixed post-divider
SATA clock on sun4i/sun7i is of type (parent) / M / 6 where
6 is fixed post-divider.
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Jonathan Liu [Tue, 8 Aug 2017 01:25:40 +0000 (11:25 +1000)]
dt-bindings: clock: sunxi-ccu: Add compatibles for sun5i CCU driver
The bindings were not updated when the sun5i CCU driver was added in
commit
5e73761786d6 ("clk: sunxi-ng: Add sun5i CCU driver").
Signed-off-by: Jonathan Liu <net147@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Sylwester Nawrocki [Fri, 21 Jul 2017 14:21:02 +0000 (16:21 +0200)]
clk: samsung: exynos542x: Enable clock rate propagation up to the EPLL
The CLK_SET_RATE_PARENT flag is added to clocks between the EPLL
and the audio subsystem clock controller so that the EPLL's output
frequency can be set indirectly with clk_set_rate() on a leaf clock.
That should be safe as EPLL is normally only used to generate clock
for the audio subsystem.
With this change we can avoid passing the EPLL clock to the ASoC
machine driver.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Sylwester Nawrocki [Mon, 17 Jul 2017 12:39:21 +0000 (14:39 +0200)]
clk: samsung: Add CLK_SET_RATE_PARENT to some AUDSS CLK CON clocks
This allows clk rate propagation up to the clock tree so EPLL
can be reprogrammed indirectly when setting rate of the Audio
Subsystem clocks.
The advantage is that sound machine driver can operate only
on the leaf clocks rather than explicitly re-configuring
the root clock (EPLL).
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Sylwester Nawrocki [Fri, 21 Jul 2017 14:18:19 +0000 (16:18 +0200)]
clk: samsung: Fix mau_epll clock definition for exynos5422
Parent clock of the MAU_EPLL gate clock on exynos5422 is
"mout_user_mau_epll", not "mout_mau_epll_clk". This change
only affects exynos5422/5800.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Elaine Zhang [Tue, 1 Aug 2017 16:22:24 +0000 (18:22 +0200)]
clk: rockchip: add special approximation to fix up fractional clk's jitter
>From Rockchips fractional divider description:
3.1.9 Fractional divider usage
To get specific frequency, clocks of I2S, SPDIF, UARTcan be generated by
fractional divider. Generally you must set that denominator is 20 times
larger than numerator to generate precise clock frequency. So the
fractional divider applies only to generate low frequency clock like
I2S, UART.
Therefore add a special approximation function that handles this
special requirement.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Elaine Zhang [Tue, 1 Aug 2017 16:21:22 +0000 (18:21 +0200)]
clk: fractional-divider: allow overriding of approximation
Fractional dividers may have special requirements concerning numerator
and denominator selection that differ from just getting the best
approximation.
For example on Rockchip socs the denominator must be at least 20 times
larger than the numerator to generate precise clock frequencies.
Therefore add the ability to provide custom approximation functions.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Elaine Zhang [Tue, 1 Aug 2017 01:17:03 +0000 (09:17 +0800)]
clk: rockchip: modify rk3128 clk driver to also support rk3126
rk3128 and rk3126 have some gate registers describe differences.
So need to make some distinctions.
The RK3126 and RK3128 Same clock description we move it to
the common clock branches.
And the different clks description use the own clock branches.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Elaine Zhang [Tue, 1 Aug 2017 01:17:04 +0000 (09:17 +0800)]
dt-bindings: add documentation for rk3126 clock
This add bindings documentation for rk3126 SoCs.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Elaine Zhang [Tue, 8 Aug 2017 07:19:33 +0000 (15:19 +0800)]
clk: rockchip: add some critical clocks for rv1108 SoC
the bus/periph/nclk_ddrupctl/pclk_ddrmon/pclk_acodecphy/pclk_pmu
no driver to handle them,
Chip design requirements for these clock to always on.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Elaine Zhang [Tue, 8 Aug 2017 07:19:17 +0000 (15:19 +0800)]
clk: rockchip: rename some of clks for rv1108 SoC
Rename some of clks to keep the consistency with the TRM.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Elaine Zhang [Tue, 8 Aug 2017 07:18:59 +0000 (15:18 +0800)]
clk: rockchip: fix up some clks describe error for rv1108 SoC
1. fix up the parent name
2. remove the CLK_IGNORE_UNUSED flag for some clk not need to always on.
3. fix up some clks regs describe error.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Elaine Zhang [Tue, 8 Aug 2017 07:18:43 +0000 (15:18 +0800)]
clk: rockchip: support more clks for rv1108
Add the description of the missing clock,
make the clock more complete.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Heiko Stuebner [Tue, 8 Aug 2017 15:21:45 +0000 (17:21 +0200)]
Merge branch 'v4.14-shared/clkids' into v4.14-clk/next
Elaine Zhang [Wed, 2 Aug 2017 08:33:04 +0000 (16:33 +0800)]
clk: rockchip: fix up the pll clks error for rv1108 SoC
fix up the lock_shift describe error.
remove the ROCKCHIP_PLL_SYNC_RATE flag for gpll.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Elaine Zhang [Wed, 2 Aug 2017 08:32:23 +0000 (16:32 +0800)]
clk: rockchip: support more rates for rv1108 cpuclk
fix up the cpuclk rates table for support more freqs.
fix up the mux_core_mask describe error.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Elaine Zhang [Wed, 2 Aug 2017 08:30:33 +0000 (16:30 +0800)]
clk: rockchip: fix up indentation of some RV1108 clock-ids
Make the code look better.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Elaine Zhang [Wed, 2 Aug 2017 08:29:48 +0000 (16:29 +0800)]
clk: rockchip: rename the clk id for HCLK_I2S1_2CH
i2s1 has 2 channels but not 8 channels.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
[and the clock id hasn't been used in either clock-driver nor dts,
so is safe to rename]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Elaine Zhang [Wed, 2 Aug 2017 08:28:39 +0000 (16:28 +0800)]
clk: rockchip: add more clk ids for rv1108
Add new clk ids for the peripherals on rv1108 soc.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Neil Armstrong [Tue, 1 Aug 2017 11:56:59 +0000 (13:56 +0200)]
clk: meson: gxbb-aoclk: Add CEC 32k clock
The CEC 32K AO Clock is a dual divider with dual counter to provide a more
precise 32768Hz clock for the CEC subsystem from the external xtal.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Neil Armstrong [Tue, 1 Aug 2017 11:56:57 +0000 (13:56 +0200)]
clk: meson: gxbb-aoclk: Switch to regmap for register access
Switch the aoclk driver to use the new bindings and switch all the
registers access to regmap only.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Neil Armstrong [Tue, 1 Aug 2017 11:56:56 +0000 (13:56 +0200)]
dt-bindings: clock: amlogic, gxbb-aoclkc: Update bindings
On the first revision of the bindings, only the gates + resets were known
in the AO Clock HW, but more registers used to configures AO clock are known
to be spread among the AO register space.
This patch adds a parent node for the entire system control zone for the AO
domain then moves the clock controller as a subnode of the system control
node.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Jerome Brunet [Mon, 31 Jul 2017 11:56:03 +0000 (13:56 +0200)]
clk: meson: gxbb: Add sd_emmc clk0 clocks
Input source 0 of the mmc controllers is not directly xtal, as currently
described in DT. Each controller is fed by a composite clock (the usual
mux, divider and gate). The muxes inputs are the xtal (default) and the
fclk_div clocks. These parents, along with the divider, should be able to
provide the necessary rates for mmc and nand operation.
The input muxes should also be able to take mpll2, mpll3 and gp0_pll but
these are precious clocks, needed for other usage. It is better if the
mmc does not use these them. For this reason, mpll2, mpll3 and gp0_pll is
not listed among the possible parents.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Jerome Brunet [Thu, 27 Jul 2017 13:09:40 +0000 (15:09 +0200)]
clk: meson: gxbb: fix clk_mclk_i958 divider flags
CLK_DIVIDER_ROUND_CLOSEST was incorrectly put in the hw.init flags
while it should have been in the divider flags
Fixes:
3c277c247eab ("clk: meson: gxbb: add cts_mclk_i958")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Jerome Brunet [Thu, 27 Jul 2017 13:09:39 +0000 (15:09 +0200)]
clk: meson: gxbb: fix meson cts_amclk divider flags
CLK_DIVIDER_ROUND_CLOSEST was incorrectly put in the hw.init flags
while it should have been in the divider flags
Fixes:
4087bd4b2170 ("clk: meson: gxbb: add cts_amclk")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Martin Blumenstingl [Fri, 28 Jul 2017 21:13:12 +0000 (23:13 +0200)]
clk: meson: meson8b: register the built-in reset controller
The clock controller also includes some reset lines. This patch
implements a reset controller to assert and de-assert these resets.
The reset controller itself is registered early (through
CLK_OF_DECLARE_DRIVER) because it is needed very early in the boot
process (to start the secondary CPU cores).
According to the public S805 datasheet there are two more reset bits
in the HHI_SYS_CPU_CLK_CNTL0 register, which are not implemented by
this patch (as these seem to be unused in Amlogic's vendor Linux kernel
sources and their u-boot tree):
- bit 15: GEN_DIV_SOFT_RESET
- bit 14: SOFT_RESET
All information was taken from the public S805 Datasheet and Amlogic's
vendor GPL kernel sources. This patch is based on an earlier version
submitted by Carlo Caione.
Suggested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Neil Armstrong [Tue, 1 Aug 2017 11:56:58 +0000 (13:56 +0200)]
dt-bindings: clock: gxbb-aoclk: Add CEC 32k clock
This patchadds the clock binding entry for the CEC 32K AO Clock.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Jerome Brunet [Mon, 31 Jul 2017 11:56:02 +0000 (13:56 +0200)]
clk: meson: gxbb: Add sd_emmc clk0 clkids
Add the clkids for the clocks feeding the input0 of the mmc controllers
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Jerome Brunet [Mon, 31 Jul 2017 11:38:32 +0000 (13:38 +0200)]
clk: meson-gxbb: expose almost every clock in the bindings
Expose all clocks which maybe used as DT bindings
Only clock ids internal the controller remain un-exposed
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Jerome Brunet [Mon, 31 Jul 2017 11:38:31 +0000 (13:38 +0200)]
clk: meson8b: expose every clock in the bindings
Expose all clocks which maybe used as DT bindings
Only clock ids internal the controller remain un-exposed (none on this
particular controller at the moment)
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Jerome Brunet [Thu, 27 Jul 2017 16:17:55 +0000 (18:17 +0200)]
clk: meson: gxbb: fix protection against undefined clks
gxbb clock driver gracefully handles case where the clkid is defined but
the clock hw pointer is not provided, as long as it is not at the end of
the hw_onecell_data array.
This patch ensure that the last entries are defined as well to handle
this particular case.
Fixes:
a70c6e06ed7c ("clk: meson: gxbb: protect against holes in the onecell_data array")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Jerome Brunet [Thu, 27 Jul 2017 16:17:54 +0000 (18:17 +0200)]
clk: meson: meson8b: fix protection against undefined clks
meson8b clock driver gracefully handles case where the clkid is defined
but the clock hw pointer is not provided, as long as it is not at the end
of the hw_onecell_data array.
This patch ensure that the last entries are defined as well to handle
this particular case.
Fixes:
e92f7cca446e ("clk: meson8b: clean up fixed rate clocks")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Icenowy Zheng [Sun, 23 Jul 2017 10:27:45 +0000 (18:27 +0800)]
clk: sunxi-ng: allow set parent clock (PLL_CPUX) for CPUX clock on H3
The CPUX clock, which is the main clock of the ARM core on Allwinner H3,
can be adjusted by changing the frequency of the PLL_CPUX clock.
Allowing setting parent clock for the CPUX clock, thus the PLL_CPUX
clock can be adjusted when adjusting the CPUX clock.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Fixes:
0577e4853bfb ("clk: sunxi-ng: Add H3 clocks")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Chen-Yu Tsai [Sun, 23 Jul 2017 10:27:44 +0000 (18:27 +0800)]
clk: sunxi-ng: h3: gate then ungate PLL CPU clk after rate change
This patch utilizes the new PLL clk notifier to gate then ungate the
PLL CPU clock after rate changes. This should prevent any system hangs
resulting from cpufreq changes to the clk.
Reported-by: Ondrej Jirman <megous@megous.com>
Fixes:
0577e4853bfb ("clk: sunxi-ng: Add H3 clocks")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Masahiro Yamada [Wed, 26 Jul 2017 03:34:35 +0000 (12:34 +0900)]
clk: uniphier: remove sLD3 SoC support
This SoC is too old. It is difficult to maintain any longer.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Stephen Boyd [Thu, 3 Aug 2017 01:38:01 +0000 (18:38 -0700)]
Merge branch 'clk-fixes' into clk-next
* clk-fixes:
clk: keystone: sci-clk: Fix sci_clk_get
clk: meson: mpll: fix mpll0 fractional part ignored
clk: samsung: exynos5420: The EPLL rate table corrections
clk: sunxi-ng: sun5i: Add clk_set_rate_parent to the CPU clock
Tero Kristo [Wed, 2 Aug 2017 18:32:13 +0000 (21:32 +0300)]
clk: keystone: sci-clk: Fix sci_clk_get
Currently a bug in the sci_clk_get implementation causes it to always
return a clock belonging to the last device in the static list of clock
data. This is due to a bug in the init code that causes the array
used by sci_clk_get to only be populated with the clocks for the last
device, as each device overwrites the entire array with its own clocks.
Fix this by calculating the actual number of clocks for the SoC, and
allocating the whole array in one go. Also, we don't need the handle
to the init data array anymore after doing this, instead we can
just compare the dev_id / clk_id against the registered clocks and
use binary search for speed.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reported-by: Dave Gerlach <d-gerlach@ti.com>
Fixes:
b745c0794e2f ("clk: keystone: Add sci-clk driver support")
Cc: Nishanth Menon <nm@ti.com>
Tested-by: Franklin Cooper <fcooper@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Stephen Boyd [Wed, 2 Aug 2017 16:11:44 +0000 (09:11 -0700)]
Merge tag 'sunxi-clk-fixes-for-4.13' of https://git./linux/kernel/git/sunxi/linux into clk-fixes
Pull one Allwinner clock fix from Chen-Yu Tsai:
One critical clock fix for sun5i (A10s/A13/R8) which enables propagation
of clock rate changes from the "cpu" clock to it's parent PLL clock.
This fixes cpufreq related crashes that have been observed on KernelCI
with the C.H.I.P. and multi_v7_defconfig.
* tag 'sunxi-clk-fixes-for-4.13' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
clk: sunxi-ng: sun5i: Add clk_set_rate_parent to the CPU clock
Stephen Boyd [Wed, 2 Aug 2017 16:09:42 +0000 (09:09 -0700)]
Merge tag 'meson-clk-fixes-for-4.13-rc4-v2' of git://github.com/baylibre/clk-meson into clk-fixes
Pull one Meson clock fix from Neil Armstrong
* tag 'meson-clk-fixes-for-4.13-rc4-v2' of git://github.com/baylibre/clk-meson:
clk: meson: mpll: fix mpll0 fractional part ignored
Jerome Brunet [Fri, 28 Jul 2017 16:32:28 +0000 (18:32 +0200)]
clk: meson: mpll: fix mpll0 fractional part ignored
mpll0 clock is special compared to the other mplls. It needs another
bit (ssen) to be set to activate the fractional part the mpll divider
Fixes:
007e6e5c5f01 ("clk: meson: mpll: add rw operation")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Jernej Škrabec [Sun, 30 Jul 2017 16:41:50 +0000 (18:41 +0200)]
clk: sunxi-ng: Wait for lock when using fractional mode
Currently ccu_frac_helper_set_rate() doesn't wait for a lock bit to be
set before returning. Because of that, unstable clock may be used.
Add a wait for lock in the helper function.
Fixes:
89a3dfb78707 ("clk: sunxi-ng: Add fractional lib")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Jernej Škrabec [Sun, 30 Jul 2017 16:41:49 +0000 (18:41 +0200)]
clk: sunxi-ng: Make fractional helper less chatty
ccu_frac_helper_read_rate() prints some info which is not really
helpful except during debugging.
Replace printk() with pr_debug().
Fixes:
89a3dfb78707 ("clk: sunxi-ng: Add fractional lib")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Jernej Škrabec [Sun, 30 Jul 2017 16:41:48 +0000 (18:41 +0200)]
clk: sunxi-ng: multiplier: Fix fractional mode
Driver for multiplier clock is missing a call to
ccu_frac_helper_enable() when fractional mode is selected.
Add a call to ccu_frac_helper_enable().
Fixes:
d77e8135b340 ("clk: sunxi-ng: multiplier: Add fractional support")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Jernej Škrabec [Sun, 30 Jul 2017 16:41:47 +0000 (18:41 +0200)]
clk: sunxi-ng: Fix fractional mode for N-M clocks
N-M factor clock driver is missing a call to ccu_frac_helper_enable()
when fractional mode is used. Additionally, most SoCs require that M
factor must be set to 0 when fractional mode is used.
Without this patch, clock keeps the old value and clk_set_rate() returns
without error.
Fixes:
6174a1e24b0d ("clk: sunxi-ng: Add N-M-factor clock support")
CC: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Sylwester Nawrocki [Fri, 21 Jul 2017 11:19:50 +0000 (13:19 +0200)]
clk: samsung: exynos5420: The EPLL rate table corrections
This patch fixes values of the EPLL K coefficient and changes
the EPLL output frequency values to match exactly what is
possible to achieve with given M, P, S, K coefficients.
This allows to avoid rounding errors and unexpected frequency
being set with clk_set_rate(), due to recalc_rate returning
different values than the PLL rate specified in the
exynos5420_epll_24mhz_tbl table. E.g. this prevents a case
where two consecutive clk_set_rate() calls with same argument
result in different PLL output frequency.
The PLL output frequencies have been calculated with formula:
f = fxtal * (M * 2^16 + K) / (P * 2^S) / 2^16
where fxtal =
24000000.
Fixes:
9842452acd ("clk: samsung: exynos542x: Add EPLL rate table")
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Martin Blumenstingl [Fri, 28 Jul 2017 21:13:11 +0000 (23:13 +0200)]
dt-bindings: clock: meson8b: describe the embedded reset controller
The Amlogic Meson8/Meson8b/Meson8m2 clock controller provides some reset
lines. These are used for example to boot the secondary CPU cores.
This patch describes the reset controller which is embedded into the
clock controller on these SoCs.
A header file is provided which provides preprocessor macros for each
reset line (to make the .dts files easier to read).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Matthias Kaehlcke [Wed, 26 Jul 2017 21:02:21 +0000 (14:02 -0700)]
clk: sunxi-ng: Fix header guard of ccu-sun8i-r.h
Remove trailing extra underscore in definition of _CCU_SUN8I_R_H
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Maxime Ripard [Fri, 21 Jul 2017 16:19:35 +0000 (18:19 +0200)]
clk: sunxi-ng: sun5i: Add clk_set_rate_parent to the CPU clock
The current CPU clock is missing the option to change the rate of its
parents, leading to improper rates calculated by cpufreq, and eventually
crashes.
Cc: <stable@vger.kernel.org>
Fixes:
5e73761786d6 ("clk: sunxi-ng: Add sun5i CCU driver")
Reported-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Rob Herring [Tue, 18 Jul 2017 21:42:52 +0000 (16:42 -0500)]
clk: Convert to using %pOF instead of full_name
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: "Emilio López" <emilio@elopez.com.ar>
Cc: Peter De Schrijver <pdeschrijver@nvidia.com>
Cc: Prashant Gaikwad <pgaikwad@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: linux-clk@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-renesas-soc@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: James Liao <jamesjj.liao@mediatek.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Yuantian Tang [Thu, 6 Apr 2017 02:21:23 +0000 (10:21 +0800)]
clk: qoriq: add pll clock to clock lookup table
Register each PLL and its division clocks to clock
lookup table to facilitate the clock look up for
clock consumer.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Yuantian Tang [Thu, 6 Apr 2017 02:21:22 +0000 (10:21 +0800)]
clk: qoriq: add clock configuration for ls1088a soc
Clock on ls1088a chip takes primary clocking input from the external
SYSCLK signal. The SYSCLK input (frequency) is multiplied using
multiple phase locked loops (PLL) to create a variety of frequencies
which can then be passed to a variety of internal logic, including
cores and peripheral IP modules.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Wolfram Sang [Tue, 18 Jul 2017 16:44:07 +0000 (18:44 +0200)]
clk: renesas: rcar-gen3-cpg: Refactor checks for accessing the div table
Do the checks for accessing the SD divider table only when the rate gets
updated, namely on init and set_rate. In all other cases, reuse the last
value. This simplifies code, runtime load, and error reporting.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Wolfram Sang [Tue, 18 Jul 2017 16:44:06 +0000 (18:44 +0200)]
clk: renesas: rcar-gen3-cpg: Drop superfluous variable
'rate' is not used, so we can use 'parent_rate' directly.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Stephen Boyd [Tue, 18 Jul 2017 23:23:26 +0000 (16:23 -0700)]
Merge branch 'clk-fixes' into clk-next
* clk-fixes:
clk: x86: Do not gate clocks enabled by the firmware
clk: gemini: Fix reset regression
Carlo Caione [Fri, 14 Jul 2017 08:23:56 +0000 (10:23 +0200)]
clk: x86: Do not gate clocks enabled by the firmware
Read the enable register to determine if the clock is already in use by
the firmware. In this case avoid gating the clock.
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Darren Hart (VMware) <dvhart@infradead.org>
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Fixes:
282a4e4ce5f9 ("platform/x86: Enable Atom PMC platform clocks")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Julia Lawall [Sat, 15 Jul 2017 20:07:36 +0000 (22:07 +0200)]
clk: mmp: Drop unnecessary static
Drop static on a local variable, when the variable is initialized before
any possible use. Thus, the static has no benefit.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@bad exists@
position p;
identifier x;
type T;
@@
static T x@p;
...
x = <+...x...+>
@@
identifier x;
expression e;
type T;
position p != bad.p;
@@
-static
T x@p;
... when != x
when strict
?x = e;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Gustavo A. R. Silva [Tue, 4 Jul 2017 22:36:50 +0000 (17:36 -0500)]
clk: moxart: remove unnecessary statics
Remove unnecessary static on local variable _base_ in both functions
moxart_of_pll_clk_init() and moxart_of_apb_clk_init(). Such variables
are initialized before being used, on every execution path throughout
the mentioned functions. The statics have no benefit and, removing
them reduce the code size.
This issue was detected using Coccinelle and the following semantic patch:
@bad exists@
position p;
identifier x;
type T;
@@
static T x@p;
...
x = <+...x...+>
@@
identifier x;
expression e;
type T;
position p != bad.p;
@@
-static
T x@p;
... when != x
when strict
?x = e;
In the following log you can see the difference in the code size. Also,
notice that the bss segment is reduced down to zero. This log is the
output of the size command, before and after the code change:
before:
text data bss dec hex filename
1724 384 128 2236 8bc drivers/clk/clk-moxart.o
after:
text data bss dec hex filename
1697 240 0 1937 791 drivers/clk/clk-moxart.o
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Georgi Djakov [Mon, 17 Jul 2017 15:35:42 +0000 (18:35 +0300)]
clk: qcom: clk-smd-rpm: Fix the reported rate of branches
As there is no way to actually query the hardware for the current clock
rate, now racalc_rate() just returns the last rate that was previously
set. But if the rate was not set yet, we return the bogus rate of 1000Hz.
The branch clocks have the same rate as their parent, so in this case we
just need to remove recalc_rate ops and then the core framework will handle
this automagically. The round_rate() is unused, so remove it as well.
Reported-by: Archit Taneja <architt@codeaurora.org>
Fixes:
00f64b58874e ("clk: qcom: Add support for SMD-RPM Clocks")
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Sean Wang [Mon, 17 Jul 2017 06:01:19 +0000 (14:01 +0800)]
clk: mediatek: fixed static checker warning in clk_cpumux_get_parent call
Fixed the signedness bug returning '(-22)' on the return type as u8 with
removing the sanity checker in clk_cpumux_get_parent() since
clk_cpumux_set_parent() always ensures validity in clk_cpumux_get_parent()
got called.
Fixes:
1e17de9049da ("clk: mediatek: add missing cpu mux causing Mediatek cpufreq can't work")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Linus Walleij [Tue, 11 Jul 2017 12:26:01 +0000 (14:26 +0200)]
clk: gemini: Fix reset regression
commit
e2860e1f62f2 ("serial: 8250_of: Add reset support")
introduced reset support for the 8250_of driver.
However it unconditionally uses the assert/deassert pair to
deassert reset on the device at probe and assert it at
remove. This does not work with systems that have a
self-deasserting reset controller, such as Gemini, that
recently added a reset controller.
As a result, the console will not probe on the Gemini with
this message:
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
of_serial: probe of
42000000.serial failed with error -524
This (-ENOTSUPP) is the error code returned by the
deassert() operation on self-deasserting reset controllers.
To work around this, implement dummy .assert() and
.deassert() operations in the Gemini combined clock and
reset controller. This fixes the issue on this system.
Cc: Joel Stanley <joel@jms.id.au>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-serial@vger.kernel.org
Fixes:
e2860e1f62f2 ("serial: 8250_of: Add reset support")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Vladimir Barinov [Sun, 9 Jul 2017 17:40:05 +0000 (20:40 +0300)]
dt: Add bindings for IDT VersaClock 5P49V5925
IDT VersaClock 5 5P49V5925 has 5 clock outputs, 4 fractional dividers.
Input clock source can be taken only from external reference clock.
Signed-off-by: Vladimir Barinov <vladimir.barinov+renesas@cogentembedded.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Vladimir Barinov [Sun, 9 Jul 2017 17:39:57 +0000 (20:39 +0300)]
clk: vc5: Add support for IDT VersaClock 5P49V5925
Update IDT VersaClock 5 driver to support 5P49V5925. This chip has only
external clock input, four fractional dividers (FODs) and five clock
outputs (four universal clock outputs and one reference clock output at
OUT0_SELB_I2C).
Signed-off-by: Vladimir Barinov <vladimir.barinov+renesas@cogentembedded.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Marek Vasut [Sun, 9 Jul 2017 13:28:14 +0000 (15:28 +0200)]
clk: vc5: Add support for IDT VersaClock 5P49V6901
Update IDT VersaClock 5 driver to support IDT VersaClock 6 5P49V6901.
This chip has two clock inputs (external XTAL or external CLKIN), four
fractional dividers (FODs) and five clock outputs (four universal clock
outputs and one reference clock output at OUT0_SELB_I2C).
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Alexey Firago <alexey_firago@mentor.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: linux-renesas-soc@vger.kernel.org
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
on Salvator-XS with the display LVDS output.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Marek Vasut [Sun, 9 Jul 2017 13:28:13 +0000 (15:28 +0200)]
clk: vc5: Add bindings for IDT VersaClock 5P49V6901
IDT VersaClock 6 5P49V6901 has 4 clock outputs, 4 fractional dividers.
Input clock source can be taken from either external crystal or from
external reference clock.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Alexey Firago <alexey_firago@mentor.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: linux-renesas-soc@vger.kernel.org
Cc: devicetree@vger.kernel.org
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Marek Vasut [Sun, 9 Jul 2017 13:28:12 +0000 (15:28 +0200)]
clk: vc5: Add support for the input frequency doubler
The VersaClock 6 has an input frequency doubler between the input
clock mux and the predivider. Add new capability flag and support
for this frequency doubler block into the driver.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Alexey Firago <alexey_firago@mentor.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: linux-renesas-soc@vger.kernel.org
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
on Salvator-XS with the display LVDS output.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Marek Vasut [Sun, 9 Jul 2017 13:28:11 +0000 (15:28 +0200)]
clk: vc5: Split clock input mux and predivider
Split the VC5 clock input mux and the predivider to more accurately
model the hardware and fix the previously incorrect assumption that
both the OUT_SEL_I2CB and the PLL are fed from the predivider.
It is in fact the clock input mux output which is directly feeding
the clock into the OUT_SEL_I2CB output, while the clock input mux
output first passes through the predivider before it is fed into
the PLL.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Alexey Firago <alexey_firago@mentor.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: linux-renesas-soc@vger.kernel.org
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
on Salvator-XS with the display LVDS output.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Marek Vasut [Sun, 9 Jul 2017 13:28:10 +0000 (15:28 +0200)]
clk: vc5: Configure the output buffer input mux on prepare
The output buffer input mux can be configured in either of three
states -- disabled, input from FOD, input from previous output.
Once the .prepare() callback of the output buffer is called, the
output buffer input mux must be set to either input from FOD or
input from previous output, it cannot be set to Disabled anymore
or the output won't work.
Default to the input from FOD if the output buffer input mux was
Disabled and the .prepare() was called on it.
Note that we do not set the output buffer input mux back to Disabled
in the .unprepare() callback as there is no obvious benefit of doing
so. We disable the entire output buffer in the .unprepare() callback
already.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Alexey Firago <alexey_firago@mentor.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: linux-renesas-soc@vger.kernel.org
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> # Salvator-XS with the display LVDS output.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Marek Vasut [Sun, 9 Jul 2017 13:28:09 +0000 (15:28 +0200)]
clk: vc5: Do not warn about disabled output buffer input muxes
The output buffer input mux can be configured in either of three
states -- disabled, input from FOD, input from previous output.
If the output buffer input mux is set to disabled, the code in
vc5_clk_out_get_parent() would consider this an invalid setting
and warn about it, which is not necessarily the case.
In case the output buffer input mux is disabled, default to input
from FOD to have some parent and don't print the warning.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Alexey Firago <alexey_firago@mentor.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: linux-renesas-soc@vger.kernel.org
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> # Salvator-XS with the display LVDS output.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Marek Vasut [Sun, 9 Jul 2017 13:28:08 +0000 (15:28 +0200)]
clk: vc5: Fix trivial typo
Fix trivial typo in vc5_clk_out_unprepare() , s/Enable/Disable/ .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Alexey Firago <alexey_firago@mentor.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: linux-renesas-soc@vger.kernel.org
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> # Salvator-XS with the display LVDS output.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Marek Vasut [Sun, 9 Jul 2017 13:28:07 +0000 (15:28 +0200)]
clk: vc5: Prevent division by zero on unconfigured outputs
In case the initial values of the FOD registers are not configured in
the OTP or by the bootloader, it is possible that the FOD registers
will contain zeroes. The code in vc5_fod_recalc_rate() immediately
feeds the FOD divider value obtained from the FOD registers into the
div64_u64() and if the FOD divider value is zero, triggers division
by zero exception.
Check if the FOD divider value is zero and return the frequency of
the FOD output as 0 Hz if it is so. This prevents the division by
zero exception.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Alexey Firago <alexey_firago@mentor.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: linux-renesas-soc@vger.kernel.org
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> # Salvator-XS with the display LVDS output.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Eugeniy Paltsev [Wed, 21 Jun 2017 19:16:26 +0000 (22:16 +0300)]
clk: axs10x: introduce AXS10X pll driver
AXS10X boards manages it's clocks using various PLLs. These PLL has same
dividers and corresponding control registers mapped to different addresses.
So we add one common driver for such PLLs.
Each PLL on AXS10X board consist of three dividers: IDIV, FBDIV and
ODIV. Output clock value is managed using these dividers.
We add pre-defined tables with supported rate values and appropriate
configurations of IDIV, FBDIV and ODIV for each value.
As of today we add support for PLLs that generate clock for the
following devices:
* ARC core on AXC CPU tiles.
* ARC PGU on ARC SDP Mainboard.
and more to come later.
By this patch we add support for two plls (arc core pll and pgu pll),
so we had to use two different init types: CLK_OF_DECLARE for arc core pll and
regular probing for pgu pll.
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vlad Zakharov <vzakhar@synopsys.com>
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
[sboyd@codeaurora.org: Silence dubious !x & y sparse warning,
make of_axs10x_pll_clk_setup() unregister clk on failure]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Geert Uytterhoeven [Wed, 17 May 2017 15:25:47 +0000 (17:25 +0200)]
clk: renesas: Allow compile-testing of all (sub)drivers
Enable compile-testing of the remaining clock drivers and subdrivers,
now dummies are available for of_clk_get_from_provider(),
of_device_compatible_match(), and rcar_rst_read_mode_pins(), and the
CPG/MSSR driver core has been converted from of_match_node() to
of_device_get_match_data().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Geert Uytterhoeven [Wed, 5 Jul 2017 11:41:00 +0000 (13:41 +0200)]
clk: renesas: r8a7792: Add IMR-LX3/LSX3 clocks
Add the module clocks for the Image Renderer Light (SRAM) Extended 3
(IMR-LX3/LSX3) Distortion Correction Engines on R-Car V2H.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Geert Uytterhoeven [Wed, 21 Jun 2017 20:02:33 +0000 (22:02 +0200)]
clk: renesas: div6: Document fields used for parent selection
Add the missing documentation for the fields in struct div6_clock
related to parent selection for DIV6 clocks with selectable parents, as
found in R/SH-Mobile SoCs.
Fixes:
c6d67fb037f4eaaf ("clk: shmobile: div6: support selectable-input clocks")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>