OSDN Git Service
Sameer Saurabh [Mon, 29 Nov 2021 13:28:29 +0000 (05:28 -0800)]
atlantic: Remove warn trace message.
Remove the warn trace message - it's not a correct check here, because
the function can still be called on the device in DOWN state
Fixes:
508f2e3dce454 ("net: atlantic: split rx and tx per-queue stats")
Signed-off-by: Sameer Saurabh <ssaurabh@marvell.com>
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Bogdanov [Mon, 29 Nov 2021 13:28:28 +0000 (05:28 -0800)]
atlantic: Fix statistics logic for production hardware
B0 is the main and widespread device revision of atlantic2 HW. In the
current state, driver will incorrectly fetch the statistics for this
revision.
Fixes:
5cfd54d7dc186 ("net: atlantic: minimal A2 fw_ops")
Signed-off-by: Dmitry Bogdanov <dbezrukov@marvell.com>
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sameer Saurabh [Mon, 29 Nov 2021 13:28:27 +0000 (05:28 -0800)]
Remove Half duplex mode speed capabilities.
Since Half Duplex mode has been deprecated by the firmware, driver should
not advertise Half Duplex speed in ethtool support link speed values.
Fixes:
071a02046c262 ("net: atlantic: A2: half duplex support")
Signed-off-by: Sameer Saurabh <ssaurabh@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikita Danilov [Mon, 29 Nov 2021 13:28:26 +0000 (05:28 -0800)]
atlantic: Add missing DIDs and fix 115c.
At the late production stages new dev ids were introduced. These are
now in production, so its important for the driver to recognize these.
And also fix the board caps for AQC115C adapter.
Fixes:
b3f0c79cba206 ("net: atlantic: A2 hw_ops skeleton")
Signed-off-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sameer Saurabh [Mon, 29 Nov 2021 13:28:25 +0000 (05:28 -0800)]
atlantic: Fix to display FW bundle version instead of FW mac version.
The correct way to reflect firmware version is to use bundle version.
Hence populating the same instead of MAC fw version.
Fixes:
c1be0bf092bd2 ("net: atlantic: common functions needed for basic A2 init/deinit hw_ops")
Signed-off-by: Sameer Saurabh <ssaurabh@marvell.com>
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikita Danilov [Mon, 29 Nov 2021 13:28:24 +0000 (05:28 -0800)]
atlatnic: enable Nbase-t speeds with base-t
When 2.5G is advertised, N-Base should be advertised against the T-base
caps. N5G is out of use in baseline code and driver should treat both 5G
and N5G (and also 2.5G and N2.5G) equally from user perspective.
Fixes:
5cfd54d7dc186 ("net: atlantic: minimal A2 fw_ops")
Signed-off-by: Nikita Danilov <ndanilov@aquantia.com>
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Bogdanov [Mon, 29 Nov 2021 13:28:23 +0000 (05:28 -0800)]
atlantic: Increase delay for fw transactions
The max waiting period (of 1 ms) while reading the data from FW shared
buffer is too small for certain types of data (e.g., stats). There's a
chance that FW could be updating buffer at the same time and driver
would be unsuccessful in reading data. Firmware manual recommends to
have 1 sec timeout to fix this issue.
Fixes:
5cfd54d7dc186 ("net: atlantic: minimal A2 fw_ops")
Signed-off-by: Dmitry Bogdanov <dbezrukov@marvell.com>
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Erik Ekman [Sun, 28 Nov 2021 12:37:11 +0000 (13:37 +0100)]
net/mlx4_en: Update reported link modes for 1/10G
When link modes were initially added in commit
2c762679435dc
("net/mlx4_en: Use PTYS register to query ethtool settings") and
later updated for the new ethtool API in commit
3d8f7cc78d0eb
("net: mlx4: use new ETHTOOL_G/SSETTINGS API") the only 1/10G non-baseT
link modes configured were 1000baseKX, 10000baseKX4 and 10000baseKR.
It looks like these got picked to represent other modes since nothing
better was available.
Switch to using more specific link modes added in commit
5711a98221443
("net: ethtool: add support for 1000BaseX and missing 10G link modes").
Tested with MCX311A-XCAT connected via DAC.
Before:
% sudo ethtool enp3s0
Settings for enp3s0:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseKX/Full
10000baseKR/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: 1000baseKX/Full
10000baseKR/Full
Advertised pause frame use: Symmetric
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Speed: 10000Mb/s
Duplex: Full
Auto-negotiation: off
Port: Direct Attach Copper
PHYAD: 0
Transceiver: internal
Supports Wake-on: d
Wake-on: d
Current message level: 0x00000014 (20)
link ifdown
Link detected: yes
With this change:
% sudo ethtool enp3s0
Settings for enp3s0:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseX/Full
10000baseCR/Full
10000baseSR/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: 1000baseX/Full
10000baseCR/Full
10000baseSR/Full
Advertised pause frame use: Symmetric
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Speed: 10000Mb/s
Duplex: Full
Auto-negotiation: off
Port: Direct Attach Copper
PHYAD: 0
Transceiver: internal
Supports Wake-on: d
Wake-on: d
Current message level: 0x00000014 (20)
link ifdown
Link detected: yes
Tested-by: Michael Stapelberg <michael@stapelberg.ch>
Signed-off-by: Erik Ekman <erik@kryo.se>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeremy Kerr [Mon, 29 Nov 2021 02:16:52 +0000 (10:16 +0800)]
mctp: test: fix skb free in test device tx
In our test device, we're currently freeing skbs in the transmit path
with kfree(), rather than kfree_skb(). This change uses the correct
kfree_skb() instead.
Fixes:
ded21b722995 ("mctp: Add test utils")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tianjia Zhang [Mon, 29 Nov 2021 09:32:12 +0000 (17:32 +0800)]
net/tls: Fix authentication failure in CCM mode
When the TLS cipher suite uses CCM mode, including AES CCM and
SM4 CCM, the first byte of the B0 block is flags, and the real
IV starts from the second byte. The XOR operation of the IV and
rec_seq should be skip this byte, that is, add the iv_offset.
Fixes:
f295b3ae9f59 ("net/tls: Add support of AES128-CCM based ciphers")
Signed-off-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com>
Cc: Vakul Garg <vakul.garg@nxp.com>
Cc: stable@vger.kernel.org # v5.2+
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 29 Nov 2021 12:39:42 +0000 (12:39 +0000)]
Merge branch 'mpls-notifications'
Benjamin Poirier says:
====================
net: mpls: Netlink notification fixes
fix missing or inaccurate route notifications when devices used in
nexthops are deleted.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Benjamin Poirier [Mon, 29 Nov 2021 06:15:06 +0000 (15:15 +0900)]
net: mpls: Remove rcu protection from nh_dev
Following the previous commit, nh_dev can no longer be accessed and
modified concurrently.
Signed-off-by: Benjamin Poirier <bpoirier@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Benjamin Poirier [Mon, 29 Nov 2021 06:15:05 +0000 (15:15 +0900)]
net: mpls: Fix notifications when deleting a device
There are various problems related to netlink notifications for mpls route
changes in response to interfaces being deleted:
* delete interface of only nexthop
DELROUTE notification is missing RTA_OIF attribute
* delete interface of non-last nexthop
NEWROUTE notification is missing entirely
* delete interface of last nexthop
DELROUTE notification is missing nexthop
All of these problems stem from the fact that existing routes are modified
in-place before sending a notification. Restructure mpls_ifdown() to avoid
changing the route in the DELROUTE cases and to create a copy in the
NEWROUTE case.
Fixes:
f8efb73c97e2 ("mpls: multipath route support")
Signed-off-by: Benjamin Poirier <bpoirier@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sven Schuchmann [Sat, 27 Nov 2021 10:47:07 +0000 (11:47 +0100)]
net: usb: lan78xx: lan78xx_phy_init(): use PHY_POLL instead of "0" if no IRQ is available
On most systems request for IRQ 0 will fail, phylib will print an error message
and fall back to polling. To fix this set the phydev->irq to PHY_POLL if no IRQ
is available.
Fixes:
cc89c323a30e ("lan78xx: Use irq_domain for phy interrupt from USB Int. EP")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Sven Schuchmann <schuchmann@schleissheimer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ole Ernst [Sat, 27 Nov 2021 09:05:45 +0000 (10:05 +0100)]
USB: NO_LPM quirk Lenovo Powered USB-C Travel Hub
This is another branded 8153 device that doesn't work well with LPM:
r8152 2-2.1:1.0 enp0s13f0u2u1: Stop submitting intr, status -71
Disable LPM to resolve the issue.
Signed-off-by: Ole Ernst <olebowle@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Luiz Angelo Daros de Luca [Fri, 26 Nov 2021 20:13:55 +0000 (17:13 -0300)]
net: dsa: realtek-smi: fix indirect reg access for ports>3
This switch family can have up to 8 UTP ports {0..7}. However,
INDIRECT_ACCESS_ADDRESS_PHYNUM_MASK was using 2 bits instead of 3,
dropping the most significant bit during indirect register reads and
writes. Reading or writing ports 4, 5, 6, and 7 registers was actually
manipulating, respectively, ports 0, 1, 2, and 3 registers.
This is not sufficient but necessary to support any variant with more
than 4 UTP ports, like RTL8367S.
rtl8365mb_phy_{read,write} will now returns -EINVAL if phy is greater
than 7.
Fixes:
4af2950c50c8 ("net: dsa: realtek-smi: add rtl8365mb subdriver for RTL8365MB-VC")
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Fri, 26 Nov 2021 18:34:21 +0000 (19:34 +0100)]
tcp: fix page frag corruption on page fault
Steffen reported a TCP stream corruption for HTTP requests
served by the apache web-server using a cifs mount-point
and memory mapping the relevant file.
The root cause is quite similar to the one addressed by
commit
20eb4f29b602 ("net: fix sk_page_frag() recursion from
memory reclaim"). Here the nested access to the task page frag
is caused by a page fault on the (mmapped) user-space memory
buffer coming from the cifs file.
The page fault handler performs an smb transaction on a different
socket, inside the same process context. Since sk->sk_allaction
for such socket does not prevent the usage for the task_frag,
the nested allocation modify "under the hood" the page frag
in use by the outer sendmsg call, corrupting the stream.
The overall relevant stack trace looks like the following:
httpd 78268 [001]
3461630.850950: probe:tcp_sendmsg_locked:
ffffffff91461d91 tcp_sendmsg_locked+0x1
ffffffff91462b57 tcp_sendmsg+0x27
ffffffff9139814e sock_sendmsg+0x3e
ffffffffc06dfe1d smb_send_kvec+0x28
[...]
ffffffffc06cfaf8 cifs_readpages+0x213
ffffffff90e83c4b read_pages+0x6b
ffffffff90e83f31 __do_page_cache_readahead+0x1c1
ffffffff90e79e98 filemap_fault+0x788
ffffffff90eb0458 __do_fault+0x38
ffffffff90eb5280 do_fault+0x1a0
ffffffff90eb7c84 __handle_mm_fault+0x4d4
ffffffff90eb8093 handle_mm_fault+0xc3
ffffffff90c74f6d __do_page_fault+0x1ed
ffffffff90c75277 do_page_fault+0x37
ffffffff9160111e page_fault+0x1e
ffffffff9109e7b5 copyin+0x25
ffffffff9109eb40 _copy_from_iter_full+0xe0
ffffffff91462370 tcp_sendmsg_locked+0x5e0
ffffffff91462370 tcp_sendmsg_locked+0x5e0
ffffffff91462b57 tcp_sendmsg+0x27
ffffffff9139815c sock_sendmsg+0x4c
ffffffff913981f7 sock_write_iter+0x97
ffffffff90f2cc56 do_iter_readv_writev+0x156
ffffffff90f2dff0 do_iter_write+0x80
ffffffff90f2e1c3 vfs_writev+0xa3
ffffffff90f2e27c do_writev+0x5c
ffffffff90c042bb do_syscall_64+0x5b
ffffffff916000ad entry_SYSCALL_64_after_hwframe+0x65
The cifs filesystem rightfully sets sk_allocations to GFP_NOFS,
we can avoid the nesting using the sk page frag for allocation
lacking the __GFP_FS flag. Do not define an additional mm-helper
for that, as this is strictly tied to the sk page frag usage.
v1 -> v2:
- use a stricted sk_page_frag() check instead of reordering the
code (Eric)
Reported-by: Steffen Froemer <sfroemer@redhat.com>
Fixes:
5640f7685831 ("net: use a per task frag allocator")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vincent Whitchurch [Fri, 26 Nov 2021 15:51:15 +0000 (16:51 +0100)]
net: stmmac: Avoid DMA_CHAN_CONTROL write if no Split Header support
The driver assumes that split headers can be enabled/disabled without
stopping/starting the device, so it writes DMA_CHAN_CONTROL from
stmmac_set_features(). However, on my system (IP v5.10a without Split
Header support), simply writing DMA_CHAN_CONTROL when DMA is running
(for example, with the commands below) leads to a TX watchdog timeout.
host$ socat TCP-LISTEN:1024,fork,reuseaddr - &
device$ ethtool -K eth0 tso off
device$ ethtool -K eth0 tso on
device$ dd if=/dev/zero bs=1M count=10 | socat - TCP4:host:1024
<tx watchdog timeout>
Note that since my IP is configured without Split Header support, the
driver always just reads and writes the same value to the
DMA_CHAN_CONTROL register.
I don't have access to any platforms with Split Header support so I
don't know if these writes to the DMA_CHAN_CONTROL while DMA is running
actually work properly on such systems. I could not find anything in
the databook that says that DMA_CHAN_CONTROL should not be written when
the DMA is running.
But on systems without Split Header support, there is in any case no
need to call enable_sph() in stmmac_set_features() at all since SPH can
never be toggled, so we can avoid the watchdog timeout there by skipping
this call.
Fixes:
8c6fc097a2f4acf ("net: stmmac: gmac4+: Add Split Header support")
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 26 Nov 2021 20:58:53 +0000 (12:58 -0800)]
Merge tag 'net-5.16-rc3' of git://git./linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Networking fixes, including fixes from netfilter.
Current release - regressions:
- r8169: fix incorrect mac address assignment
- vlan: fix underflow for the real_dev refcnt when vlan creation
fails
- smc: avoid warning of possible recursive locking
Current release - new code bugs:
- vsock/virtio: suppress used length validation
- neigh: fix crash in v6 module initialization error path
Previous releases - regressions:
- af_unix: fix change in behavior in read after shutdown
- igb: fix netpoll exit with traffic, avoid warning
- tls: fix splice_read() when starting mid-record
- lan743x: fix deadlock in lan743x_phy_link_status_change()
- marvell: prestera: fix bridge port operation
Previous releases - always broken:
- tcp_cubic: fix spurious Hystart ACK train detections for
not-cwnd-limited flows
- nexthop: fix refcount issues when replacing IPv6 groups
- nexthop: fix null pointer dereference when IPv6 is not enabled
- phylink: force link down and retrigger resolve on interface change
- mptcp: fix delack timer length calculation and incorrect early
clearing
- ieee802154: handle iftypes as u32, prevent shift-out-of-bounds
- nfc: virtual_ncidev: change default device permissions
- netfilter: ctnetlink: fix error codes and flags used for kernel
side filtering of dumps
- netfilter: flowtable: fix IPv6 tunnel addr match
- ncsi: align payload to 32-bit to fix dropped packets
- iavf: fix deadlock and loss of config during VF interface reset
- ice: avoid bpf_prog refcount underflow
- ocelot: fix broken PTP over IP and PTP API violations
Misc:
- marvell: mvpp2: increase MTU limit when XDP enabled"
* tag 'net-5.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (94 commits)
net: dsa: microchip: implement multi-bridge support
net: mscc: ocelot: correctly report the timestamping RX filters in ethtool
net: mscc: ocelot: set up traps for PTP packets
net: ptp: add a definition for the UDP port for IEEE 1588 general messages
net: mscc: ocelot: create a function that replaces an existing VCAP filter
net: mscc: ocelot: don't downgrade timestamping RX filters in SIOCSHWTSTAMP
net: hns3: fix incorrect components info of ethtool --reset command
net: hns3: fix one incorrect value of page pool info when queried by debugfs
net: hns3: add check NULL address for page pool
net: hns3: fix VF RSS failed problem after PF enable multi-TCs
net: qed: fix the array may be out of bound
net/smc: Don't call clcsock shutdown twice when smc shutdown
net: vlan: fix underflow for the real_dev refcnt
ptp: fix filter names in the documentation
ethtool: ioctl: fix potential NULL deref in ethtool_set_coalesce()
nfc: virtual_ncidev: change default device permissions
net/sched: sch_ets: don't peek at classes beyond 'nbands'
net: stmmac: Disable Tx queues when reconfiguring the interface
selftests: tls: test for correct proto_ops
tls: fix replacing proto_ops
...
Oleksij Rempel [Fri, 26 Nov 2021 12:39:26 +0000 (13:39 +0100)]
net: dsa: microchip: implement multi-bridge support
Current driver version is able to handle only one bridge at time.
Configuring two bridges on two different ports would end up shorting this
bridges by HW. To reproduce it:
ip l a name br0 type bridge
ip l a name br1 type bridge
ip l s dev br0 up
ip l s dev br1 up
ip l s lan1 master br0
ip l s dev lan1 up
ip l s lan2 master br1
ip l s dev lan2 up
Ping on lan1 and get response on lan2, which should not happen.
This happened, because current driver version is storing one global "Port VLAN
Membership" and applying it to all ports which are members of any
bridge.
To solve this issue, we need to handle each port separately.
This patch is dropping the global port member storage and calculating
membership dynamically depending on STP state and bridge participation.
Note: STP support was broken before this patch and should be fixed
separately.
Fixes:
c2e866911e25 ("net: dsa: microchip: break KSZ9477 DSA driver into two files")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20211126123926.2981028-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Linus Torvalds [Fri, 26 Nov 2021 20:19:13 +0000 (12:19 -0800)]
Merge tag 'acpi-5.16-rc3' of git://git./linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These fix a NULL pointer dereference in the CPPC library code and a
locking issue related to printing the names of ACPI device nodes in
the device properties framework.
Specifics:
- Fix NULL pointer dereference in the CPPC library code occuring on
hybrid systems without CPPC support (Rafael Wysocki).
- Avoid attempts to acquire a semaphore with interrupts off when
printing the names of ACPI device nodes and clean up code on top of
that fix (Sakari Ailus)"
* tag 'acpi-5.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: CPPC: Add NULL pointer check to cppc_get_perf()
ACPI: Make acpi_node_get_parent() local
ACPI: Get acpi_device's parent from the parent field
Linus Torvalds [Fri, 26 Nov 2021 20:14:50 +0000 (12:14 -0800)]
Merge tag 'pm-5.16-rc3' of git://git./linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These address three issues in the intel_pstate driver and fix two
problems related to hibernation.
Specifics:
- Make intel_pstate work correctly on Ice Lake server systems with
out-of-band performance control enabled (Adamos Ttofari).
- Fix EPP handling in intel_pstate during CPU offline and online in
the active mode (Rafael Wysocki).
- Make intel_pstate support ITMT on asymmetric systems with
overclocking enabled (Srinivas Pandruvada).
- Fix hibernation image saving when using the user space interface
based on the snapshot special device file (Evan Green).
- Make the hibernation code release the snapshot block device using
the same mode that was used when acquiring it (Thomas Zeitlhofer)"
* tag 'pm-5.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM: hibernate: Fix snapshot partial write lengths
PM: hibernate: use correct mode for swsusp_close()
cpufreq: intel_pstate: ITMT support for overclocked system
cpufreq: intel_pstate: Fix active mode offline/online EPP handling
cpufreq: intel_pstate: Add Ice Lake server to out-of-band IDs
Linus Torvalds [Fri, 26 Nov 2021 20:01:31 +0000 (12:01 -0800)]
Merge tag 'fuse-fixes-5.16-rc3' of git://git./linux/kernel/git/mszeredi/fuse
Pull fuse fix from Miklos Szeredi:
"Fix a regression caused by a bugfix in the previous release. The
symptom is a VM_BUG_ON triggered from splice to the fuse device.
Unfortunately the original bugfix was already backported to a number
of stable releases, so this fix-fix will need to be backported as
well"
* tag 'fuse-fixes-5.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: release pipe buf after last use
Jakub Kicinski [Fri, 26 Nov 2021 19:38:23 +0000 (11:38 -0800)]
Merge branch 'fix-broken-ptp-over-ip-on-ocelot-switches'
Vladimir Oltean says:
====================
Fix broken PTP over IP on Ocelot switches
Changes in v2: added patch 5, added Richard's ack for the whole series
sans patch 5 which is new.
Po Liu reported recently that timestamping PTP over IPv4 is broken using
the felix driver on NXP LS1028A. This has been known for a while, of
course, since it has always been broken. The reason is because IP PTP
packets are currently treated as unknown IP multicast, which is not
flooded to the CPU port in the ocelot driver design, so packets don't
reach the ptp4l program.
The series solves the problem by installing packet traps per port when
the timestamping ioctl is called, depending on the RX filter selected
(L2, L4 or both).
====================
Link: https://lore.kernel.org/r/20211126172845.3149260-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean [Fri, 26 Nov 2021 17:28:45 +0000 (19:28 +0200)]
net: mscc: ocelot: correctly report the timestamping RX filters in ethtool
The driver doesn't support RX timestamping for non-PTP packets, but it
declares that it does. Restrict the reported RX filters to PTP v2 over
L2 and over L4.
Fixes:
4e3b0468e6d7 ("net: mscc: PTP Hardware Clock (PHC) support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean [Fri, 26 Nov 2021 17:28:44 +0000 (19:28 +0200)]
net: mscc: ocelot: set up traps for PTP packets
IEEE 1588 support was declared too soon for the Ocelot switch. Out of
reset, this switch does not apply any special treatment for PTP packets,
i.e. when an event message is received, the natural tendency is to
forward it by MAC DA/VLAN ID. This poses a problem when the ingress port
is under a bridge, since user space application stacks (written
primarily for endpoint ports, not switches) like ptp4l expect that PTP
messages are always received on AF_PACKET / AF_INET sockets (depending
on the PTP transport being used), and never being autonomously
forwarded. Any forwarding, if necessary (for example in Transparent
Clock mode) is handled in software by ptp4l. Having the hardware forward
these packets too will cause duplicates which will confuse endpoints
connected to these switches.
So PTP over L2 barely works, in the sense that PTP packets reach the CPU
port, but they reach it via flooding, and therefore reach lots of other
unwanted destinations too. But PTP over IPv4/IPv6 does not work at all.
This is because the Ocelot switch have a separate destination port mask
for unknown IP multicast (which PTP over IP is) flooding compared to
unknown non-IP multicast (which PTP over L2 is) flooding. Specifically,
the driver allows the CPU port to be in the PGID_MC port group, but not
in PGID_MCIPV4 and PGID_MCIPV6. There are several presentations from
Allan Nielsen which explain that the embedded MIPS CPU on Ocelot
switches is not very powerful at all, so every penny they could save by
not allowing flooding to the CPU port module matters. Unknown IP
multicast did not make it.
The de facto consensus is that when a switch is PTP-aware and an
application stack for PTP is running, switches should have some sort of
trapping mechanism for PTP packets, to extract them from the hardware
data path. This avoids both problems:
(a) PTP packets are no longer flooded to unwanted destinations
(b) PTP over IP packets are no longer denied from reaching the CPU since
they arrive there via a trap and not via flooding
It is not the first time when this change is attempted. Last time, the
feedback from Allan Nielsen and Andrew Lunn was that the traps should
not be installed by default, and that PTP-unaware switching may be
desired for some use cases:
https://patchwork.ozlabs.org/project/netdev/patch/
20190813025214.18601-5-yangbo.lu@nxp.com/
To address that feedback, the present patch adds the necessary packet
traps according to the RX filter configuration transmitted by user space
through the SIOCSHWTSTAMP ioctl. Trapping is done via VCAP IS2, where we
keep 5 filters, which are amended each time RX timestamping is enabled
or disabled on a port:
- 1 for PTP over L2
- 2 for PTP over IPv4 (UDP ports 319 and 320)
- 2 for PTP over IPv6 (UDP ports 319 and 320)
The cookie by which these filters (invisible to tc) are identified is
strategically chosen such that it does not collide with the filters used
for the ocelot-8021q tagging protocol by the Felix driver, or with the
MRP traps set up by the Ocelot library.
Other alternatives were considered, like patching user space to do
something, but there are so many ways in which PTP packets could be made
to reach the CPU, generically speaking, that "do what?" is a very valid
question. The ptp4l program from the linuxptp stack already attempts to
do something: it calls setsockopt(IP_ADD_MEMBERSHIP) (and
PACKET_ADD_MEMBERSHIP, respectively) which translates in both cases into
a dev_mc_add() on the interface, in the kernel:
https://github.com/richardcochran/linuxptp/blob/v3.1.1/udp.c#L73
https://github.com/richardcochran/linuxptp/blob/v3.1.1/raw.c
Reality shows that this is not sufficient in case the interface belongs
to a switchdev driver, as dev_mc_add() does not show the intention to
trap a packet to the CPU, but rather the intention to not drop it (it is
strictly for RX filtering, same as promiscuous does not mean to send all
traffic to the CPU, but to not drop traffic with unknown MAC DA). This
topic is a can of worms in itself, and it would be great if user space
could just stay out of it.
On the other hand, setting up PTP traps privately within the driver is
not new by any stretch of the imagination:
https://elixir.bootlin.com/linux/v5.16-rc2/source/drivers/net/ethernet/mellanox/mlxsw/spectrum_ptp.c#L833
https://elixir.bootlin.com/linux/v5.16-rc2/source/drivers/net/dsa/hirschmann/hellcreek.c#L1050
https://elixir.bootlin.com/linux/v5.16-rc2/source/include/linux/dsa/sja1105.h#L21
So this is the approach taken here as well. The difference here being
that we prepare and destroy the traps per port, dynamically at runtime,
as opposed to driver init time, because apparently, PTP-unaware
forwarding is a use case.
Fixes:
4e3b0468e6d7 ("net: mscc: PTP Hardware Clock (PHC) support")
Reported-by: Po Liu <po.liu@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean [Fri, 26 Nov 2021 17:28:43 +0000 (19:28 +0200)]
net: ptp: add a definition for the UDP port for IEEE 1588 general messages
As opposed to event messages (Sync, PdelayReq etc) which require
timestamping, general messages (Announce, FollowUp etc) do not.
In PTP they are part of different streams of data.
IEEE 1588-2008 Annex D.2 "UDP port numbers" states that the UDP
destination port assigned by IANA is 319 for event messages, and 320 for
general messages. Yet the kernel seems to be missing the definition for
general messages. This patch adds it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean [Fri, 26 Nov 2021 17:28:42 +0000 (19:28 +0200)]
net: mscc: ocelot: create a function that replaces an existing VCAP filter
VCAP (Versatile Content Aware Processor) is the TCAM-based engine behind
tc flower offload on ocelot, among other things. The ingress port mask
on which VCAP rules match is present as a bit field in the actual key of
the rule. This means that it is possible for a rule to be shared among
multiple source ports. When the rule is added one by one on each desired
port, that the ingress port mask of the key must be edited and rewritten
to hardware.
But the API in ocelot_vcap.c does not allow for this. For one thing,
ocelot_vcap_filter_add() and ocelot_vcap_filter_del() are not symmetric,
because ocelot_vcap_filter_add() works with a preallocated and
prepopulated filter and programs it to hardware, and
ocelot_vcap_filter_del() does both the job of removing the specified
filter from hardware, as well as kfreeing it. That is to say, the only
option of editing a filter in place, which is to delete it, modify the
structure and add it back, does not work because it results in
use-after-free.
This patch introduces ocelot_vcap_filter_replace, which trivially
reprograms a VCAP entry to hardware, at the exact same index at which it
existed before, without modifying any list or allocating any memory.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean [Fri, 26 Nov 2021 17:28:41 +0000 (19:28 +0200)]
net: mscc: ocelot: don't downgrade timestamping RX filters in SIOCSHWTSTAMP
The ocelot driver, when asked to timestamp all receiving packets, 1588
v1 or NTP, says "nah, here's 1588 v2 for you".
According to this discussion:
https://patchwork.kernel.org/project/netdevbpf/patch/
20211104133204.19757-8-martin.kaistra@linutronix.de/#
24577647
drivers that downgrade from a wider request to a narrower response (or
even a response where the intersection with the request is empty) are
buggy, and should return -ERANGE instead. This patch fixes that.
Fixes:
4e3b0468e6d7 ("net: mscc: PTP Hardware Clock (PHC) support")
Suggested-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Fri, 26 Nov 2021 19:36:31 +0000 (11:36 -0800)]
Merge branch 'net-hns3-add-some-fixes-for-net'
Guangbin Huang says:
====================
net: hns3: add some fixes for -net
This series adds some fixes for the HNS3 ethernet driver.
====================
Link: https://lore.kernel.org/r/20211126120318.33921-1-huangguangbin2@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jie Wang [Fri, 26 Nov 2021 12:03:18 +0000 (20:03 +0800)]
net: hns3: fix incorrect components info of ethtool --reset command
Currently, HNS3 driver doesn't clear the reset flags of components after
successfully executing reset, it causes userspace info of
"Components reset" and "Components not reset" is incorrect.
So fix this problem by clear corresponding reset flag after reset process.
Fixes:
ddccc5e368a3 ("net: hns3: add support for triggering reset by ethtool")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Hao Chen [Fri, 26 Nov 2021 12:03:17 +0000 (20:03 +0800)]
net: hns3: fix one incorrect value of page pool info when queried by debugfs
Currently, when user queries page pool info by debugfs command
"cat page_pool_info", the cnt of allocated page for page pool may be
incorrect because of memory inconsistency problem caused by compiler
optimization.
So this patch uses READ_ONCE() to read value of pages_state_hold_cnt to
fix this problem.
Fixes:
850bfb912a6d ("net: hns3: debugfs add support dumping page pool info")
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Hao Chen [Fri, 26 Nov 2021 12:03:16 +0000 (20:03 +0800)]
net: hns3: add check NULL address for page pool
When page pool is not enabled, its address value is still NULL and page
pool should not be accessed, so add a check for it.
Fixes:
850bfb912a6d ("net: hns3: debugfs add support dumping page pool info")
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Guangbin Huang [Fri, 26 Nov 2021 12:03:15 +0000 (20:03 +0800)]
net: hns3: fix VF RSS failed problem after PF enable multi-TCs
When PF is set to multi-TCs and configured mapping relationship between
priorities and TCs, the hardware will active these settings for this PF
and its VFs.
In this case when VF just uses one TC and its rx packets contain priority,
and if the priority is not mapped to TC0, as other TCs of VF is not valid,
hardware always put this kind of packets to the queue 0. It cause this kind
of packets of VF can not be used RSS function.
To fix this problem, set tc mode of all unused TCs of VF to the setting of
TC0, then rx packet with priority which map to unused TC will be direct to
TC0.
Fixes:
e2cb1dec9779 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
zhangyue [Thu, 25 Nov 2021 11:36:10 +0000 (19:36 +0800)]
net: qed: fix the array may be out of bound
If the variable 'p_bit->flags' is always 0,
the loop condition is always 0.
The variable 'j' may be greater than or equal to 32.
At this time, the array 'p_aeu->bits[32]' may be out
of bound.
Signed-off-by: zhangyue <zhangyue1@kylinos.cn>
Link: https://lore.kernel.org/r/20211125113610.273841-1-zhangyue1@kylinos.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Linus Torvalds [Fri, 26 Nov 2021 19:24:32 +0000 (11:24 -0800)]
Merge tag 'for-5.16-rc2-tag' of git://git./linux/kernel/git/kdave/linux
Pull btrfs fix from David Sterba:
"One more fix to the lzo code, a missing put_page causing memory leaks
when some error branches are taken"
* tag 'for-5.16-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: fix the memory leak caused in lzo_compress_pages()
Tony Lu [Fri, 26 Nov 2021 02:41:35 +0000 (10:41 +0800)]
net/smc: Don't call clcsock shutdown twice when smc shutdown
When applications call shutdown() with SHUT_RDWR in userspace,
smc_close_active() calls kernel_sock_shutdown(), and it is called
twice in smc_shutdown().
This fixes this by checking sk_state before do clcsock shutdown, and
avoids missing the application's call of smc_shutdown().
Link: https://lore.kernel.org/linux-s390/1f67548e-cbf6-0dce-82b5-10288a4583bd@linux.ibm.com/
Fixes:
606a63c9783a ("net/smc: Ensure the active closing peer first closes clcsock")
Signed-off-by: Tony Lu <tonylu@linux.alibaba.com>
Reviewed-by: Wen Gu <guwen@linux.alibaba.com>
Acked-by: Karsten Graul <kgraul@linux.ibm.com>
Link: https://lore.kernel.org/r/20211126024134.45693-1-tonylu@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ziyang Xuan [Fri, 26 Nov 2021 01:59:42 +0000 (09:59 +0800)]
net: vlan: fix underflow for the real_dev refcnt
Inject error before dev_hold(real_dev) in register_vlan_dev(),
and execute the following testcase:
ip link add dev dummy1 type dummy
ip link add name dummy1.100 link dummy1 type vlan id 100
ip link del dev dummy1
When the dummy netdevice is removed, we will get a WARNING as following:
=======================================================================
refcount_t: decrement hit 0; leaking memory.
WARNING: CPU: 2 PID: 0 at lib/refcount.c:31 refcount_warn_saturate+0xbf/0x1e0
and an endless loop of:
=======================================================================
unregister_netdevice: waiting for dummy1 to become free. Usage count = -
1073741824
That is because dev_put(real_dev) in vlan_dev_free() be called without
dev_hold(real_dev) in register_vlan_dev(). It makes the refcnt of real_dev
underflow.
Move the dev_hold(real_dev) to vlan_dev_init() which is the call-back of
ndo_init(). That makes dev_hold() and dev_put() for vlan's real_dev
symmetrical.
Fixes:
563bcbae3ba2 ("net: vlan: fix a UAF in vlan_dev_real_dev()")
Reported-by: Petr Machata <petrm@nvidia.com>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Link: https://lore.kernel.org/r/20211126015942.2918542-1-william.xuanziyang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Fri, 26 Nov 2021 03:19:21 +0000 (19:19 -0800)]
ptp: fix filter names in the documentation
All the filter names are missing _PTP in them.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Link: https://lore.kernel.org/r/20211126031921.2466944-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Julian Wiedmann [Fri, 26 Nov 2021 17:55:43 +0000 (18:55 +0100)]
ethtool: ioctl: fix potential NULL deref in ethtool_set_coalesce()
ethtool_set_coalesce() now uses both the .get_coalesce() and
.set_coalesce() callbacks. But the check for their availability is
buggy, so changing the coalesce settings on a device where the driver
provides only _one_ of the callbacks results in a NULL pointer
dereference instead of an -EOPNOTSUPP.
Fix the condition so that the availability of both callbacks is
ensured. This also matches the netlink code.
Note that reproducing this requires some effort - it only affects the
legacy ioctl path, and needs a specific combination of driver options:
- have .get_coalesce() and .coalesce_supported but no
.set_coalesce(), or
- have .set_coalesce() but no .get_coalesce(). Here eg. ethtool doesn't
cause the crash as it first attempts to call ethtool_get_coalesce()
and bails out on error.
Fixes:
f3ccfda19319 ("ethtool: extend coalesce setting uAPI with CQE mode")
Cc: Yufeng Mo <moyufeng@huawei.com>
Cc: Huazhong Tan <tanhuazhong@huawei.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Link: https://lore.kernel.org/r/20211126175543.28000-1-jwi@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Thadeu Lima de Souza Cascardo [Thu, 25 Nov 2021 14:14:57 +0000 (11:14 -0300)]
nfc: virtual_ncidev: change default device permissions
Device permissions is S_IALLUGO, with many unnecessary bits. Remove them
and also remove read and write permissions from group and others.
Before the change:
crwsrwsrwt 1 0 0 10, 125 Nov 25 13:59 /dev/virtual_nci
After the change:
crw------- 1 0 0 10, 125 Nov 25 14:05 /dev/virtual_nci
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Bongsu Jeon <bongsu.jeon@samsung.com>
Link: https://lore.kernel.org/r/20211125141457.716921-1-cascardo@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Davide Caratti [Wed, 24 Nov 2021 16:14:40 +0000 (17:14 +0100)]
net/sched: sch_ets: don't peek at classes beyond 'nbands'
when the number of DRR classes decreases, the round-robin active list can
contain elements that have already been freed in ets_qdisc_change(). As a
consequence, it's possible to see a NULL dereference crash, caused by the
attempt to call cl->qdisc->ops->peek(cl->qdisc) when cl->qdisc is NULL:
BUG: kernel NULL pointer dereference, address:
0000000000000018
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: 0000 [#1] PREEMPT SMP NOPTI
CPU: 1 PID: 910 Comm: mausezahn Not tainted 5.16.0-rc1+ #475
Hardware name: Red Hat KVM, BIOS 1.11.1-4.module+el8.1.0+4066+
0f1aadab 04/01/2014
RIP: 0010:ets_qdisc_dequeue+0x129/0x2c0 [sch_ets]
Code: c5 01 41 39 ad e4 02 00 00 0f 87 18 ff ff ff 49 8b 85 c0 02 00 00 49 39 c4 0f 84 ba 00 00 00 49 8b ad c0 02 00 00 48 8b 7d 10 <48> 8b 47 18 48 8b 40 38 0f ae e8 ff d0 48 89 c3 48 85 c0 0f 84 9d
RSP: 0000:
ffffbb36c0b5fdd8 EFLAGS:
00010287
RAX:
ffff956678efed30 RBX:
0000000000000000 RCX:
0000000000000000
RDX:
0000000000000002 RSI:
ffffffff9b938dc9 RDI:
0000000000000000
RBP:
ffff956678efed30 R08:
e2f3207fe360129c R09:
0000000000000000
R10:
0000000000000001 R11:
0000000000000001 R12:
ffff956678efeac0
R13:
ffff956678efe800 R14:
ffff956611545000 R15:
ffff95667ac8f100
FS:
00007f2aa9120740(0000) GS:
ffff95667b800000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
0000000000000018 CR3:
000000011070c000 CR4:
0000000000350ee0
Call Trace:
<TASK>
qdisc_peek_dequeued+0x29/0x70 [sch_ets]
tbf_dequeue+0x22/0x260 [sch_tbf]
__qdisc_run+0x7f/0x630
net_tx_action+0x290/0x4c0
__do_softirq+0xee/0x4f8
irq_exit_rcu+0xf4/0x130
sysvec_apic_timer_interrupt+0x52/0xc0
asm_sysvec_apic_timer_interrupt+0x12/0x20
RIP: 0033:0x7f2aa7fc9ad4
Code: b9 ff ff 48 8b 54 24 18 48 83 c4 08 48 89 ee 48 89 df 5b 5d e9 ed fc ff ff 0f 1f 00 66 2e 0f 1f 84 00 00 00 00 00 f3 0f 1e fa <53> 48 83 ec 10 48 8b 05 10 64 33 00 48 8b 00 48 85 c0 0f 85 84 00
RSP: 002b:
00007ffe5d33fab8 EFLAGS:
00000202
RAX:
0000000000000002 RBX:
0000561f72c31460 RCX:
0000561f72c31720
RDX:
0000000000000002 RSI:
0000561f72c31722 RDI:
0000561f72c31720
RBP:
000000000000002a R08:
00007ffe5d33fa40 R09:
0000000000000014
R10:
0000000000000000 R11:
0000000000000246 R12:
0000561f7187e380
R13:
0000000000000000 R14:
0000000000000000 R15:
0000561f72c31460
</TASK>
Modules linked in: sch_ets sch_tbf dummy rfkill iTCO_wdt intel_rapl_msr iTCO_vendor_support intel_rapl_common joydev virtio_balloon lpc_ich i2c_i801 i2c_smbus pcspkr ip_tables xfs libcrc32c crct10dif_pclmul crc32_pclmul crc32c_intel ahci libahci ghash_clmulni_intel serio_raw libata virtio_blk virtio_console virtio_net net_failover failover sunrpc dm_mirror dm_region_hash dm_log dm_mod
CR2:
0000000000000018
Ensuring that 'alist' was never zeroed [1] was not sufficient, we need to
remove from the active list those elements that are no more SP nor DRR.
[1] https://lore.kernel.org/netdev/
60d274838bf09777f0371253416e8af71360bc08.
1633609148.git.dcaratti@redhat.com/
v3: fix race between ets_qdisc_change() and ets_qdisc_dequeue() delisting
DRR classes beyond 'nbands' in ets_qdisc_change() with the qdisc lock
acquired, thanks to Cong Wang.
v2: when a NULL qdisc is found in the DRR active list, try to dequeue skb
from the next list item.
Reported-by: Hangbin Liu <liuhangbin@gmail.com>
Fixes:
dcc68b4d8084 ("net: sch_ets: Add a new Qdisc")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Link: https://lore.kernel.org/r/7a5c496eed2d62241620bdbb83eb03fb9d571c99.1637762721.git.dcaratti@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rafael J. Wysocki [Fri, 26 Nov 2021 18:45:31 +0000 (19:45 +0100)]
Merge branch 'acpi-properties'
Merge fix and cleanup related to the management of ACPI device
properties for 5.16-rc3.
* acpi-properties:
ACPI: Make acpi_node_get_parent() local
ACPI: Get acpi_device's parent from the parent field
Rafael J. Wysocki [Fri, 26 Nov 2021 18:44:40 +0000 (19:44 +0100)]
Merge branch 'pm-sleep'
Merge hibernation-related fixes for 5.16-rc3.
* pm-sleep:
PM: hibernate: Fix snapshot partial write lengths
PM: hibernate: use correct mode for swsusp_close()
Yannick Vignon [Wed, 24 Nov 2021 15:47:31 +0000 (16:47 +0100)]
net: stmmac: Disable Tx queues when reconfiguring the interface
The Tx queues were not disabled in situations where the driver needed to
stop the interface to apply a new configuration. This could result in a
kernel panic when doing any of the 3 following actions:
* reconfiguring the number of queues (ethtool -L)
* reconfiguring the size of the ring buffers (ethtool -G)
* installing/removing an XDP program (ip l set dev ethX xdp)
Prevent the panic by making sure netif_tx_disable is called when stopping
an interface.
Without this patch, the following kernel panic can be observed when doing
any of the actions above:
Unable to handle kernel paging request at virtual address
ffff80001238d040
[....]
Call trace:
dwmac4_set_addr+0x8/0x10
dev_hard_start_xmit+0xe4/0x1ac
sch_direct_xmit+0xe8/0x39c
__dev_queue_xmit+0x3ec/0xaf0
dev_queue_xmit+0x14/0x20
[...]
[ end trace
0000000000000002 ]---
Fixes:
5fabb01207a2d ("net: stmmac: Add initial XDP support")
Fixes:
aa042f60e4961 ("net: stmmac: Add support to Ethtool get/set ring parameters")
Fixes:
0366f7e06a6be ("net: stmmac: add ethtool support for get/set channels")
Signed-off-by: Yannick Vignon <yannick.vignon@nxp.com>
Link: https://lore.kernel.org/r/20211124154731.1676949-1-yannick.vignon@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Linus Torvalds [Fri, 26 Nov 2021 18:33:17 +0000 (10:33 -0800)]
Merge tag 'char-misc-5.16-rc3' of git://git./linux/kernel/git/gregkh/char-misc
Pull char/misc driver fix from Greg KH:
"Here is a single binder driver fix for 5.16-rc3.
It resolves a problem reported in the set of binder fixes that went
into 5.16-rc1. It has been in linux-next for a while with no reported
problems"
* tag 'char-misc-5.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
binder: fix test regression due to sender_euid change
Linus Torvalds [Fri, 26 Nov 2021 18:27:43 +0000 (10:27 -0800)]
Merge tag 'staging-5.16-rc3' of git://git./linux/kernel/git/gregkh/staging
Pull staging fixes from Greg KH:
"Here are some small staging driver fixes and one driver removal for
5.16-rc3.
The fixes resolve a number of small issues found in 5.16-rc1, nothing
huge at all. The driver removal was due to a platform being removed in
5.16-rc1, but this driver was forgotten about. It wasn't being built
anymore so it's safe to delete.
All have been in linux-next for a while with no reported problems"
* tag 'staging-5.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: rtl8192e: Fix use after free in _rtl92e_pci_disconnect()
staging: greybus: Add missing rwsem around snd_ctl_remove() calls
staging: Remove Netlogic XLP network driver
staging: r8188eu: fix a memory leak in rtw_wx_read32()
staging: r8188eu: use GFP_ATOMIC under spinlock
staging: r8188eu: Use kzalloc() with GFP_ATOMIC in atomic context
staging/fbtft: Fix backlight
staging: r8188eu: Fix breakage introduced when 5G code was removed
Linus Torvalds [Fri, 26 Nov 2021 18:22:47 +0000 (10:22 -0800)]
Merge tag 'usb-5.16-rc1' of git://git./linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of small USB fixes for reported problems for
5.16-rc3
They include:
- typec driver fixes
- new usb-serial driver ids
- usb hub enumeration issues that were much reported
- gadget driver fixes
- dwc3 driver fix
- chipidea driver fixe
All of these have been in linux-next with no reported problems"
* tag 'usb-5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: serial: option: add Fibocom FM101-GL variants
usb: typec: tipd: Fix initialization sequence for cd321x
usb: typec: tipd: Fix typo in cd321x_switch_power_state
usb: hub: Fix locking issues with address0_mutex
USB: serial: pl2303: fix GC type detection
USB: serial: option: add Telit LE910S1 0x9200 composition
usb: chipidea: ci_hdrc_imx: fix potential error pointer dereference in probe
usb: hub: Fix usb enumeration issue due to address0 race
usb: typec: fusb302: Fix masking of comparator and bc_lvl interrupts
usb: dwc3: leave default DMA for PCI devices
usb: dwc2: hcd_queue: Fix use of floating point literal
usb: dwc3: gadget: Fix null pointer exception
usb: gadget: udc-xilinx: Fix an error handling path in 'xudc_probe()'
usb: xhci: tegra: Check padctrl interrupt presence in device tree
usb: dwc2: gadget: Fix ISOC flow for elapsed frames
usb: dwc3: gadget: Check for L1/L2/U3 for Start Transfer
usb: dwc3: gadget: Ignore NoStream after End Transfer
usb: dwc3: core: Revise GHWPARAMS9 offset
Linus Torvalds [Fri, 26 Nov 2021 18:10:19 +0000 (10:10 -0800)]
Merge tag 'mmc-v5.16-rc1' of git://git./linux/kernel/git/ulfh/mmc
Pull MMC host fixes from Ulf Hansson:
- mmc_spi: Add SPI IDs to silence warning
- sdhci: Fix ADMA for PAGE_SIZE >= 64KiB
- sdhci-esdhc-imx: Disable broken CMDQ for imx8qm/imx8qxp/imx8mm
* tag 'mmc-v5.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: spi: Add device-tree SPI IDs
mmc: sdhci: Fix ADMA for PAGE_SIZE >= 64KiB
mmc: sdhci-esdhc-imx: disable CMDQ support
Linus Torvalds [Fri, 26 Nov 2021 17:59:55 +0000 (09:59 -0800)]
Merge branch 'i2c/for-current' of git://git./linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"I2C has an interrupt storm fix for the i801, better timeout handling
for the new virtio driver, and some documentation fixes this time"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
docs: i2c: smbus-protocol: mention the repeated start condition
i2c: virtio: disable timeout handling
i2c: i801: Fix interrupt storm from SMB_ALERT signal
i2c: i801: Restore INTREN on unload
dt-bindings: i2c: imx-lpi2c: Fix i.MX 8QM compatible matching
Linus Torvalds [Fri, 26 Nov 2021 17:54:13 +0000 (09:54 -0800)]
Merge tag 'for-linus-5.16c-rc3-tag' of git://git./linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
- Kconfig fix to make it possible to control building of the privcmd
driver
- three fixes for issues identified by the kernel test robot
- a five-patch series to simplify timeout handling for Xen PV driver
initialization
- two patches to fix error paths in xenstore/xenbus driver
initialization
* tag 'for-linus-5.16c-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: make HYPERVISOR_set_debugreg() always_inline
xen: make HYPERVISOR_get_debugreg() always_inline
xen: detect uninitialized xenbus in xenbus_init
xen: flag xen_snd_front to be not essential for system boot
xen: flag pvcalls-front to be not essential for system boot
xen: flag hvc_xen to be not essential for system boot
xen: flag xen_drm_front to be not essential for system boot
xen: add "not_essential" flag to struct xenbus_driver
xen/pvh: add missing prototype to header
xen: don't continue xenstore initialization in case of errors
xen/privcmd: make option visible in Kconfig
Linus Torvalds [Fri, 26 Nov 2021 17:30:24 +0000 (09:30 -0800)]
Merge tag 'arm64-fixes' of git://git./linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Three arm64 fixes.
The main one is a fix to the way in which we evaluate the macro
arguments to our uaccess routines, which we _think_ might be the root
cause behind some unkillable tasks we've seen in the Android arm64 CI
farm (testing is ongoing). In any case, it's worth fixing.
Other than that, we've toned down an over-zealous VM_BUG_ON() and
fixed ftrace stack unwinding in a bunch of cases.
Summary:
- Evaluate uaccess macro arguments outside of the critical section
- Tighten up VM_BUG_ON() in pmd_populate_kernel() to avoid false positive
- Fix ftrace stack unwinding using HAVE_FUNCTION_GRAPH_RET_ADDR_PTR"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: uaccess: avoid blocking within critical sections
arm64: mm: Fix VM_BUG_ON(mm != &init_mm) for trans_pgd
arm64: ftrace: use HAVE_FUNCTION_GRAPH_RET_ADDR_PTR
Qu Wenruo [Sat, 20 Nov 2021 08:34:11 +0000 (16:34 +0800)]
btrfs: fix the memory leak caused in lzo_compress_pages()
[BUG]
Fstests generic/027 is pretty easy to trigger a slow but steady memory
leak if run with "-o compress=lzo" mount option.
Normally one single run of generic/027 is enough to eat up at least 4G ram.
[CAUSE]
In commit
d4088803f511 ("btrfs: subpage: make lzo_compress_pages()
compatible") we changed how @page_in is released.
But that refactoring makes @page_in only released after all pages being
compressed.
This leaves error path not releasing @page_in. And by "error path"
things like incompressible data will also be treated as an error
(-E2BIG).
Thus it can cause a memory leak if even nothing wrong happened.
[FIX]
Add check under @out label to release @page_in when needed, so when we
hit any error, the input page is properly released.
Reported-by: Josef Bacik <josef@toxicpanda.com>
Fixes:
d4088803f511 ("btrfs: subpage: make lzo_compress_pages() compatible")
Reviewed-and-tested-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Jakub Kicinski [Fri, 26 Nov 2021 03:28:20 +0000 (19:28 -0800)]
Merge branch 'tls-splice_read-fixes'
Jakub Kicinski says:
====================
tls: splice_read fixes
As I work my way to unlocked and zero-copy TLS Rx the obvious bugs
in the splice_read implementation get harder and harder to ignore.
This is to say the fixes here are discovered by code inspection,
I'm not aware of anyone actually using splice_read.
====================
Link: https://lore.kernel.org/r/20211124232557.2039757-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Wed, 24 Nov 2021 23:25:57 +0000 (15:25 -0800)]
selftests: tls: test for correct proto_ops
Previous patch fixes overriding callbacks incorrectly. Triggering
the crash in sendpage_locked would be more spectacular but it's
hard to get to, so take the easier path of proving this is broken
and call getname. We're currently getting IPv4 socket info on an
IPv6 socket.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Wed, 24 Nov 2021 23:25:56 +0000 (15:25 -0800)]
tls: fix replacing proto_ops
We replace proto_ops whenever TLS is configured for RX. But our
replacement also overrides sendpage_locked, which will crash
unless TX is also configured. Similarly we plug both of those
in for TLS_HW (NIC crypto offload) even tho TLS_HW has a completely
different implementation for TX.
Last but not least we always plug in something based on inet_stream_ops
even though a few of the callbacks differ for IPv6 (getname, release,
bind).
Use a callback building method similar to what we do for struct proto.
Fixes:
c46234ebb4d1 ("tls: RX path for ktls")
Fixes:
d4ffb02dee2f ("net/tls: enable sk_msg redirect to tls socket egress")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Wed, 24 Nov 2021 23:25:55 +0000 (15:25 -0800)]
selftests: tls: test splicing decrypted records
Add tests for half-received and peeked records.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Wed, 24 Nov 2021 23:25:54 +0000 (15:25 -0800)]
tls: splice_read: fix accessing pre-processed records
recvmsg() will put peek()ed and partially read records onto the rx_list.
splice_read() needs to consult that list otherwise it may miss data.
Align with recvmsg() and also put partially-read records onto rx_list.
tls_sw_advance_skb() is pretty pointless now and will be removed in
net-next.
Fixes:
692d7b5d1f91 ("tls: Fix recvmsg() to be able to peek across multiple records")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Wed, 24 Nov 2021 23:25:53 +0000 (15:25 -0800)]
selftests: tls: test splicing cmsgs
Make sure we correctly reject splicing non-data records.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Wed, 24 Nov 2021 23:25:52 +0000 (15:25 -0800)]
tls: splice_read: fix record type check
We don't support splicing control records. TLS 1.3 changes moved
the record type check into the decrypt if(). The skb may already
be decrypted and still be an alert.
Note that decrypt_skb_update() is idempotent and updates ctx->decrypted
so the if() is pointless.
Reorder the check for decryption errors with the content type check
while touching them. This part is not really a bug, because if
decryption failed in TLS 1.3 content type will be DATA, and for
TLS 1.2 it will be correct. Nevertheless its strange to touch output
before checking if the function has failed.
Fixes:
fedf201e1296 ("net: tls: Refactor control message handling on recv")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Wed, 24 Nov 2021 23:25:51 +0000 (15:25 -0800)]
selftests: tls: add tests for handling of bad records
Test broken records.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Wed, 24 Nov 2021 23:25:50 +0000 (15:25 -0800)]
selftests: tls: factor out cmsg send/receive
Add helpers for sending and receiving special record types.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Wed, 24 Nov 2021 23:25:49 +0000 (15:25 -0800)]
selftests: tls: add helper for creating sock pairs
We have the same code 3 times, about to add a fourth copy.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Linus Torvalds [Fri, 26 Nov 2021 02:21:20 +0000 (18:21 -0800)]
Merge tag 'drm-fixes-2021-11-26' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"No idea if turkey comes before pull request processing, but here's the
regular week's fixes. A bunch for amdgpu, nouveau adds support for a
new GPU (like a PCI ID addition), and a scattering of fixes across
i915/hyperv/aspeed/vc4.
Specifics:
amdgpu:
- SRIOV fixes
- dma-buf double free fix
- Display fixes for GPU resets
- Fix DSC powergating regression
- GPU TSC fixes
- Interrupt handler overflow fixes
- Endian fix in IP discovery table handling
- Aldebaran ASPM fix
- Fix overclocking regression on older asics
- Backlight/ACPI fix
amdkfd:
- SVM fixes
- VMA removal race fix
hyperv:
- removal fix
aspeed:
- vga_pw sysfs file fix
vc4:
- error checking fix
nouveau:
- support GA106
- fix a few error checks
i915:
- fix wakeref handling around PXP suspend"
* tag 'drm-fixes-2021-11-26' of git://anongit.freedesktop.org/drm/drm: (25 commits)
drm/amd/display: update bios scratch when setting backlight
drm/amdgpu/pm: fix powerplay OD interface
drm/amdgpu: Skip ASPM programming on aldebaran
drm/amdgpu: fix byteorder error in amdgpu discovery
drm/amdgpu: enable Navi retry fault wptr overflow
drm/amdgpu: enable Navi 48-bit IH timestamp counter
drm/amdkfd: simplify drain retry fault
drm/amdkfd: handle VMA remove race
drm/amdkfd: process exit and retry fault race
drm/amdgpu: IH process reset count when restart
drm/amdgpu/gfx9: switch to golden tsc registers for renoir+
drm/amdgpu/gfx10: add wraparound gpu counter check for APUs as well
drm/amdgpu: move kfd post_reset out of reset_sriov function
drm/amd/display: Fixed DSC would not PG after removing DSC stream
drm/amd/display: Reset link encoder assignments for GPU reset
drm/amd/display: Set plane update flags for all planes in reset
drm/amd/display: Fix DPIA outbox timeout after GPU reset
drm/amdgpu: Fix double free of dmabuf
drm/amdgpu: Fix MMIO HDP flush on SRIOV
drm/i915/gt: Hold RPM wakelock during PXP suspend
...
Dave Airlie [Fri, 26 Nov 2021 00:36:06 +0000 (10:36 +1000)]
Merge tag 'drm-intel-fixes-2021-11-24' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
Fix wakeref handling of PXP suspend.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/YZ65bsPOK+6JLv0d@intel.com
Dave Airlie [Fri, 26 Nov 2021 00:08:10 +0000 (10:08 +1000)]
Merge tag 'drm-misc-fixes-2021-11-25' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
One removal fix for hyperv, one fix in aspeed for the vga_pw sysfs file
content, one error-checking fix for vc4 and two fixes for nouveau, one
to support a new device and another one to properly check for errors.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20211125101819.ynu7zgbs7yfwedri@houat
Dave Airlie [Thu, 25 Nov 2021 23:24:15 +0000 (09:24 +1000)]
Merge tag 'amd-drm-fixes-5.16-2021-11-24' of https://gitlab.freedesktop.org/agd5f/linux into drm-fixes
amd-drm-fixes-5.16-2021-11-24:
amdgpu:
- SRIOV fixes
- dma-buf double free fix
- Display fixes for GPU resets
- Fix DSC powergating regression
- GPU TSC fixes
- Interrupt handler overflow fixes
- Endian fix in IP discovery table handling
- Aldebaran ASPM fix
- Fix overclocking regression on older asics
- Backlight/ACPI fix
amdkfd:
- SVM fixes
- VMA removal race fix
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211124212056.6327-1-alexander.deucher@amd.com
Linus Torvalds [Thu, 25 Nov 2021 19:06:05 +0000 (11:06 -0800)]
Merge tag 'block-5.16-2021-11-25' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- NVMe pull request via Christoph:
- Add a NO APST quirk for a Kioxia device (Enzo Matsumiya)
- Fix write zeroes pi (Klaus Jensen)
- Various TCP transport fixes (Maurizio Lombardi and Varun
Prakash)
- Ignore invalid fast_io_fail_tmo values (Maurizio Lombardi)
- Use IOCB_NOWAIT only if the filesystem supports it (Maurizio
Lombardi)
- Module loading fix (Ming)
- Kerneldoc warning fix (Yang)
* tag 'block-5.16-2021-11-25' of git://git.kernel.dk/linux-block:
block: fix parameter not described warning
nvmet: use IOCB_NOWAIT only if the filesystem supports it
nvme: fix write zeroes pi
nvme-fabrics: ignore invalid fast_io_fail_tmo values
nvme-pci: add NO APST quirk for Kioxia device
nvme-tcp: fix memory leak when freeing a queue
nvme-tcp: validate R2T PDU in nvme_tcp_handle_r2t()
nvmet-tcp: fix incomplete data digest send
nvmet-tcp: fix memory leak when performing a controller reset
nvmet-tcp: add an helper to free the cmd buffers
nvmet-tcp: fix a race condition between release_queue and io_work
block: avoid to touch unloaded module instance when opening bdev
Linus Torvalds [Thu, 25 Nov 2021 18:57:45 +0000 (10:57 -0800)]
Merge tag 'io_uring-5.16-2021-11-25' of git://git.kernel.dk/linux-block
Pull io_uring fixes from Jens Axboe:
"A locking fix for link traversal, and fixing up an outdated function
name in a comment"
* tag 'io_uring-5.16-2021-11-25' of git://git.kernel.dk/linux-block:
io_uring: correct link-list traversal locking
io_uring: fix missed comment from *task_file rename
Linus Torvalds [Thu, 25 Nov 2021 18:48:14 +0000 (10:48 -0800)]
Merge tag '5.16-rc2-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"Four small cifs/smb3 fixes:
- two multichannel fixes
- fix problem noted by kernel test robot
- update internal version number"
* tag '5.16-rc2-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: update internal version number
smb2: clarify rc initialization in smb2_reconnect
cifs: populate server_hostname for extra channels
cifs: nosharesock should be set on new server
Linus Torvalds [Thu, 25 Nov 2021 18:41:28 +0000 (10:41 -0800)]
Merge tag 'asm-generic-5.16-2' of git://git./linux/kernel/git/arnd/asm-generic
Pull asm-generic syscall table update from Arnd Bergmann:
"André Almeida sends an update for the newly added futex_waitv syscall
that was initially only added to a few architectures.
Some additional ones have since made it through architecture
maintainer trees, this finishes the remaining ones"
* tag 'asm-generic-5.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
futex: Wireup futex_waitv syscall
Linus Torvalds [Thu, 25 Nov 2021 18:31:37 +0000 (10:31 -0800)]
Merge tag 'arm-fixes-5.16-2' of git://git./linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"There are only a few devicetree fixes this time:
- one outdated devicetree property that slipped into the newly added
ExynosAutov9 support
- three changes to Broadcom SoCs that had incorrect number values for
interrupts or irqchips.
In the MAINTAINERS file, Nishanth Menon gets listed for TI K3 SoCs,
while Taichi Sugaya and Takao Orito take ownership of the Socionext
Milbeaut platform.
All other changes are for SoC specific drivers, fixing:
- A missing NULL pointer check in the mediatek memory driver
- An integer overflow issue in the Arm smccc firwmare interface
- A false-positive fortify-source check
- Error handling fixes for optee and smci
- Incorrect message format in one SCMI call"
* tag 'arm-fixes-5.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
memory: mtk-smi: Fix a null dereference for the ostd
arm64: dts: exynos: drop samsung,ufs-shareability-reg-offset in ExynosAutov9
MAINTAINERS: Update maintainer entry for keystone platforms
MAINTAINERS: Add entry to MAINTAINERS for Milbeaut
firmware: smccc: Fix check for ARCH_SOC_ID not implemented
ARM: socfpga: Fix crash with CONFIG_FORTIRY_SOURCE
firmware: arm_scmi: Fix type error assignment in voltage protocol
firmware: arm_scmi: Fix type error in sensor protocol
firmware: arm_scmi: pm: Propagate return value to caller
firmware: arm_scmi: Fix base agent discover response
optee: fix kfree NULL pointer
ARM: dts: bcm2711: Fix PCIe interrupts
ARM: dts: BCM5301X: Add interrupt properties to GPIO node
ARM: dts: BCM5301X: Fix I2C controller interrupt
firmware: arm_scmi: Fix null de-reference on error path
Linus Torvalds [Thu, 25 Nov 2021 18:13:56 +0000 (10:13 -0800)]
Merge tag 'folio-5.16b' of git://git.infradead.org/users/willy/pagecache
Pull folio fixes from Matthew Wilcox:
"In the course of preparing the folio changes for iomap for next merge
window, we discovered some problems that would be nice to address now:
- Renaming multi-page folios to large folios.
mapping_multi_page_folio_support() is just a little too long, so we
settled on mapping_large_folio_support(). That meant renaming, eg
folio_test_multi() to folio_test_large().
Rename AS_THP_SUPPORT to match
- I hadn't included folio wrappers for zero_user_segments(), etc.
Also, multi-page^W^W large folio support is now independent of
CONFIG_TRANSPARENT_HUGEPAGE, so machines with HIGHMEM always need
to fall back to the out-of-line zero_user_segments().
Remove FS_THP_SUPPORT to match
- The build bots finally got round to telling me that I missed a
couple of architectures when adding flush_dcache_folio(). Christoph
suggested that we just add linux/cacheflush.h and not rely on
asm-generic/cacheflush.h"
* tag 'folio-5.16b' of git://git.infradead.org/users/willy/pagecache:
mm: Add functions to zero portions of a folio
fs: Rename AS_THP_SUPPORT and mapping_thp_support
fs: Remove FS_THP_SUPPORT
mm: Remove folio_test_single
mm: Rename folio_test_multi to folio_test_large
Add linux/cacheflush.h
Yang Guang [Thu, 25 Nov 2021 16:20:55 +0000 (00:20 +0800)]
block: fix parameter not described warning
The build warning:
block/blk-core.c:968: warning: Function parameter or member 'iob'
not described in 'bio_poll'.
Fixes:
5a72e899ceb4 ("block: add a struct io_comp_batch argument to fops->iopoll()")
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Yang Guang <yang.guang5@zte.com.cn>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Dylan Hung [Thu, 25 Nov 2021 02:44:32 +0000 (10:44 +0800)]
mdio: aspeed: Fix "Link is Down" issue
The issue happened randomly in runtime. The message "Link is Down" is
popped but soon it recovered to "Link is Up".
The "Link is Down" results from the incorrect read data for reading the
PHY register via MDIO bus. The correct sequence for reading the data
shall be:
1. fire the command
2. wait for command done (this step was missing)
3. wait for data idle
4. read data from data register
Cc: stable@vger.kernel.org
Fixes:
f160e99462c6 ("net: phy: Add mdio-aspeed")
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20211125024432.15809-1-dylan_hung@aspeedtech.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jesse Brandeburg [Tue, 23 Nov 2021 20:40:00 +0000 (12:40 -0800)]
igb: fix netpoll exit with traffic
Oleksandr brought a bug report where netpoll causes trace
messages in the log on igb.
Danielle brought this back up as still occurring, so we'll try
again.
[22038.710800] ------------[ cut here ]------------
[22038.710801] igb_poll+0x0/0x1440 [igb] exceeded budget in poll
[22038.710802] WARNING: CPU: 12 PID: 40362 at net/core/netpoll.c:155 netpoll_poll_dev+0x18a/0x1a0
As Alex suggested, change the driver to return work_done at the
exit of napi_poll, which should be safe to do in this driver
because it is not polling multiple queues in this single napi
context (multiple queues attached to one MSI-X vector). Several
other drivers contain the same simple sequence, so I hope
this will not create new problems.
Fixes:
16eb8815c235 ("igb: Refactor clean_rx_irq to reduce overhead and improve performance")
Reported-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Reported-by: Danielle Ratson <danieller@nvidia.com>
Suggested-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Tested-by: Danielle Ratson <danieller@nvidia.com>
Link: https://lore.kernel.org/r/20211123204000.1597971-1-jesse.brandeburg@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Juergen Gross [Thu, 25 Nov 2021 09:20:56 +0000 (10:20 +0100)]
xen: make HYPERVISOR_set_debugreg() always_inline
HYPERVISOR_set_debugreg() is being called from noinstr code, so it
should be attributed "always_inline".
Fixes:
7361fac0465ba96ec8f ("x86/xen: Make set_debugreg() noinstr")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: https://lore.kernel.org/r/20211125092056.24758-3-jgross@suse.com
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Juergen Gross [Thu, 25 Nov 2021 09:20:55 +0000 (10:20 +0100)]
xen: make HYPERVISOR_get_debugreg() always_inline
HYPERVISOR_get_debugreg() is being called from noinstr code, so it
should be attributed "always_inline".
Fixes:
f4afb713e5c3a4419ba ("x86/xen: Make get_debugreg() noinstr")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: https://lore.kernel.org/r/20211125092056.24758-2-jgross@suse.com
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Jens Axboe [Thu, 25 Nov 2021 14:51:24 +0000 (07:51 -0700)]
Merge tag 'nvme-5.16-2021-11-25' of git://git.infradead.org/nvme into block-5.16
Pull NVMe fixes from Christoph:
"nvme fixes for Linux 5.16
- add a NO APST quirk for a Kioxia device (Enzo Matsumiya)
- fix write zeroes pi (Klaus Jensen)
- various TCP transport fixes (Maurizio Lombardi and Varun Prakash)
- ignore invalid fast_io_fail_tmo values (Maurizio Lombardi)
- use IOCB_NOWAIT only if the filesystem supports it (Maurizio Lombardi)"
* tag 'nvme-5.16-2021-11-25' of git://git.infradead.org/nvme:
nvmet: use IOCB_NOWAIT only if the filesystem supports it
nvme: fix write zeroes pi
nvme-fabrics: ignore invalid fast_io_fail_tmo values
nvme-pci: add NO APST quirk for Kioxia device
nvme-tcp: fix memory leak when freeing a queue
nvme-tcp: validate R2T PDU in nvme_tcp_handle_r2t()
nvmet-tcp: fix incomplete data digest send
nvmet-tcp: fix memory leak when performing a controller reset
nvmet-tcp: add an helper to free the cmd buffers
nvmet-tcp: fix a race condition between release_queue and io_work
Maurizio Lombardi [Mon, 22 Nov 2021 10:08:27 +0000 (11:08 +0100)]
nvmet: use IOCB_NOWAIT only if the filesystem supports it
Submit I/O requests with the IOCB_NOWAIT flag set only if
the underlying filesystem supports it.
Fixes:
50a909db36f2 ("nvmet: use IOCB_NOWAIT for file-ns buffered I/O")
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Yong Wu [Wed, 24 Nov 2021 08:50:42 +0000 (09:50 +0100)]
memory: mtk-smi: Fix a null dereference for the ostd
We add the ostd setting for mt8195. It introduces a KE for the
previous SoC which doesn't have ostd setting. This is the log:
Unable to handle kernel NULL pointer dereference at virtual address
0000000000000080
...
pc : mtk_smi_larb_config_port_gen2_general+0x64/0x130
lr : mtk_smi_larb_resume+0x54/0x98
...
Call trace:
mtk_smi_larb_config_port_gen2_general+0x64/0x130
pm_generic_runtime_resume+0x2c/0x48
__genpd_runtime_resume+0x30/0xa8
genpd_runtime_resume+0x94/0x2c8
__rpm_callback+0x44/0x150
rpm_callback+0x6c/0x78
rpm_resume+0x310/0x558
__pm_runtime_resume+0x3c/0x88
In the code: larbostd = larb->larb_gen->ostd[larb->larbid],
if "larb->larb_gen->ostd" is null, the "larbostd" is the offset(e.g.
0x80 above), it's also a valid value, then accessing "larbostd[i]" in the
"for" loop will cause the KE above. To avoid this issue, initialize
"larbostd" to NULL when the SoC doesn't have ostd setting.
Fixes:
fe6dd2a4017d ("memory: mtk-smi: mt8195: Add initial setting for smi-larb")
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20211108082429.15080-1-yong.wu@mediatek.com
Link: https://lore.kernel.org/r/20211124085042.9649-3-krzysztof.kozlowski@canonical.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Chanho Park [Wed, 24 Nov 2021 08:50:41 +0000 (09:50 +0100)]
arm64: dts: exynos: drop samsung,ufs-shareability-reg-offset in ExynosAutov9
samsung,ufs-shareability-reg-offset is not necessary anymore since it
was integrated into the second argument of samsung,sysreg.
Fixes:
31bbac5263aa ("arm64: dts: exynos: add initial support for exynosautov9 SoC")
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20211102064826.15796-1-chanho61.park@samsung.com
Link: https://lore.kernel.org/r/20211124085042.9649-2-krzysztof.kozlowski@canonical.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Nishanth Menon [Tue, 23 Nov 2021 00:17:25 +0000 (18:17 -0600)]
MAINTAINERS: Update maintainer entry for keystone platforms
Switch the kernel tree for keystone to the consolidated ti tree and add
myself as primary maintainer for keystone platforms to offset Santosh's
workload.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Link: https://lore.kernel.org/r/20211123001725.21422-1-nm@ti.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
André Almeida [Wed, 24 Nov 2021 13:21:12 +0000 (10:21 -0300)]
futex: Wireup futex_waitv syscall
Wireup futex_waitv syscall for all remaining archs.
Signed-off-by: André Almeida <andrealmeid@collabora.com>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Miklos Szeredi [Thu, 25 Nov 2021 13:05:18 +0000 (14:05 +0100)]
fuse: release pipe buf after last use
Checking buf->flags should be done before the pipe_buf_release() is called
on the pipe buffer, since releasing the buffer might modify the flags.
This is exactly what page_cache_pipe_buf_release() does, and which results
in the same VM_BUG_ON_PAGE(PageLRU(page)) that the original patch was
trying to fix.
Reported-by: Justin Forbes <jmforbes@linuxtx.org>
Fixes:
712a951025c0 ("fuse: fix page stealing")
Cc: <stable@vger.kernel.org> # v2.6.35
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Greg Kroah-Hartman [Thu, 25 Nov 2021 12:27:40 +0000 (13:27 +0100)]
Merge tag 'usb-serial-5.16-rc3' of https://git./linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 5.16-rc3
Here's a fix for a pl2303 type-detection issue and some new modem
devices ids.
All but the last commit have been in linux-next, and with no reported
issues.
* tag 'usb-serial-5.16-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add Fibocom FM101-GL variants
USB: serial: pl2303: fix GC type detection
USB: serial: option: add Telit LE910S1 0x9200 composition
Jakub Kicinski [Thu, 25 Nov 2021 03:02:23 +0000 (19:02 -0800)]
Merge branch 'net-smc-fixes-2021-11-24'
Karsten Graul says:
====================
net/smc: fixes 2021-11-24
Patch 1 from DaXing fixes a possible loop in smc_listen().
Patch 2 prevents a NULL pointer dereferencing while iterating
over the lower network devices.
====================
Link: https://lore.kernel.org/r/20211124123238.471429-1-kgraul@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Guo DaXing [Wed, 24 Nov 2021 12:32:38 +0000 (13:32 +0100)]
net/smc: Fix loop in smc_listen
The kernel_listen function in smc_listen will fail when all the available
ports are occupied. At this point smc->clcsock->sk->sk_data_ready has
been changed to smc_clcsock_data_ready. When we call smc_listen again,
now both smc->clcsock->sk->sk_data_ready and smc->clcsk_data_ready point
to the smc_clcsock_data_ready function.
The smc_clcsock_data_ready() function calls lsmc->clcsk_data_ready which
now points to itself resulting in an infinite loop.
This patch restores smc->clcsock->sk->sk_data_ready with the old value.
Fixes:
a60a2b1e0af1 ("net/smc: reduce active tcp_listen workers")
Signed-off-by: Guo DaXing <guodaxing@huawei.com>
Acked-by: Tony Lu <tonylu@linux.alibaba.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Karsten Graul [Wed, 24 Nov 2021 12:32:37 +0000 (13:32 +0100)]
net/smc: Fix NULL pointer dereferencing in smc_vlan_by_tcpsk()
Coverity reports a possible NULL dereferencing problem:
in smc_vlan_by_tcpsk():
6. returned_null: netdev_lower_get_next returns NULL (checked 29 out of 30 times).
7. var_assigned: Assigning: ndev = NULL return value from netdev_lower_get_next.
1623 ndev = (struct net_device *)netdev_lower_get_next(ndev, &lower);
CID
1468509 (#1 of 1): Dereference null return value (NULL_RETURNS)
8. dereference: Dereferencing a pointer that might be NULL ndev when calling is_vlan_dev.
1624 if (is_vlan_dev(ndev)) {
Remove the manual implementation and use netdev_walk_all_lower_dev() to
iterate over the lower devices. While on it remove an obsolete function
parameter comment.
Fixes:
cb9d43f67754 ("net/smc: determine vlan_id of stacked net_device")
Suggested-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Thu, 25 Nov 2021 02:40:09 +0000 (18:40 -0800)]
Merge branch 'phylink-resolve-fixes'
Marek Behún says:
====================
phylink resolve fixes
With information from me and my nagging, Russell has produced two fixes
for phylink, which add code that triggers another phylink_resolve() from
phylink_resolve(), if certain conditions are met:
interface is being changed
or
link is down and previous link was up
These are needed because sometimes the PCS callbacks may provide stale
values if link / speed / ...
====================
Link: https://lore.kernel.org/r/20211123154403.32051-1-kabel@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Russell King (Oracle) [Tue, 23 Nov 2021 15:44:03 +0000 (16:44 +0100)]
net: phylink: Force retrigger in case of latched link-fail indicator
On mv88e6xxx 1G/2.5G PCS, the SerDes register 4.2001.2 has the following
description:
This register bit indicates when link was lost since the last
read. For the current link status, read this register
back-to-back.
Thus to get current link state, we need to read the register twice.
But doing that in the link change interrupt handler would lead to
potentially ignoring link down events, which we really want to avoid.
Thus this needs to be solved in phylink's resolve, by retriggering
another resolve in the event when PCS reports link down and previous
link was up, and by re-reading PCS state if the previous link was down.
The wrong value is read when phylink requests change from sgmii to
2500base-x mode, and link won't come up. This fixes the bug.
Fixes:
9525ae83959b ("phylink: add phylink infrastructure")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Russell King (Oracle) [Tue, 23 Nov 2021 15:44:02 +0000 (16:44 +0100)]
net: phylink: Force link down and retrigger resolve on interface change
On PHY state change the phylink_resolve() function can read stale
information from the MAC and report incorrect link speed and duplex to
the kernel message log.
Example with a Marvell 88X3310 PHY connected to a SerDes port on Marvell
88E6393X switch:
- PHY driver triggers state change due to PHY interface mode being
changed from 10gbase-r to 2500base-x due to copper change in speed
from 10Gbps to 2.5Gbps, but the PHY itself either hasn't yet changed
its interface to the host, or the interrupt about loss of SerDes link
hadn't arrived yet (there can be a delay of several milliseconds for
this), so we still think that the 10gbase-r mode is up
- phylink_resolve()
- phylink_mac_pcs_get_state()
- this fills in speed=10g link=up
- interface mode is updated to 2500base-x but speed is left at 10Gbps
- phylink_major_config()
- interface is changed to 2500base-x
- phylink_link_up()
- mv88e6xxx_mac_link_up()
- .port_set_speed_duplex()
- speed is set to 10Gbps
- reports "Link is Up - 10Gbps/Full" to dmesg
Afterwards when the interrupt finally arrives for mv88e6xxx, another
resolve is forced in which we get the correct speed from
phylink_mac_pcs_get_state(), but since the interface is not being
changed anymore, we don't call phylink_major_config() but only
phylink_mac_config(), which does not set speed/duplex anymore.
To fix this, we need to force the link down and trigger another resolve
on PHY interface change event.
Fixes:
9525ae83959b ("phylink: add phylink infrastructure")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Heiner Kallweit [Wed, 24 Nov 2021 07:16:25 +0000 (08:16 +0100)]
lan743x: fix deadlock in lan743x_phy_link_status_change()
Usage of phy_ethtool_get_link_ksettings() in the link status change
handler isn't needed, and in combination with the referenced change
it results in a deadlock. Simply remove the call and replace it with
direct access to phydev->speed. The duplex argument of
lan743x_phy_update_flowcontrol() isn't used and can be removed.
Fixes:
c10a485c3de5 ("phy: phy_ethtool_ksettings_get: Lock the phy for consistency")
Reported-by: Alessandro B Maurici <abmaurici@gmail.com>
Tested-by: Alessandro B Maurici <abmaurici@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/40e27f76-0ba3-dcef-ee32-a78b9df38b0f@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eric Dumazet [Tue, 23 Nov 2021 20:25:35 +0000 (12:25 -0800)]
tcp_cubic: fix spurious Hystart ACK train detections for not-cwnd-limited flows
While testing BIG TCP patch series, I was expecting that TCP_RR workloads
with 80KB requests/answers would send one 80KB TSO packet,
then being received as a single GRO packet.
It turns out this was not happening, and the root cause was that
cubic Hystart ACK train was triggering after a few (2 or 3) rounds of RPC.
Hystart was wrongly setting CWND/SSTHRESH to 30, while my RPC
needed a budget of ~20 segments.
Ideally these TCP_RR flows should not exit slow start.
Cubic Hystart should reset itself at each round, instead of assuming
every TCP flow is a bulk one.
Note that even after this patch, Hystart can still trigger, depending
on scheduling artifacts, but at a higher CWND/SSTHRESH threshold,
keeping optimal TSO packet sizes.
Tested:
ip link set dev eth0 gro_ipv6_max_size 131072 gso_ipv6_max_size 131072
nstat -n; netperf -H ... -t TCP_RR -l 5 -- -r 80000,80000 -K cubic; nstat|egrep "Ip6InReceives|Hystart|Ip6OutRequests"
Before:
8605
Ip6InReceives 87541 0.0
Ip6OutRequests 129496 0.0
TcpExtTCPHystartTrainDetect 1 0.0
TcpExtTCPHystartTrainCwnd 30 0.0
After:
8760
Ip6InReceives 88514 0.0
Ip6OutRequests 87975 0.0
Fixes:
ae27e98a5152 ("[TCP] CUBIC v2.3")
Co-developed-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Link: https://lore.kernel.org/r/20211123202535.1843771-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Florian Fainelli [Tue, 23 Nov 2021 22:24:22 +0000 (14:24 -0800)]
MAINTAINERS: Update B53 section to cover SF2 switch driver
Update the B53 Ethernet switch section to contain
drivers/net/dsa/bcm_sf2*.
Reported-by: Russell King (Oracle) <linux@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20211123222422.3745485-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Thu, 25 Nov 2021 01:02:43 +0000 (17:02 -0800)]
Merge tag 'ieee802154-for-net-2021-11-24' of git://git./linux/kernel/git/sschmidt/wpan
Stefan Schmidt says:
====================
pull-request: ieee802154 for net 2021-11-24
A fix from Alexander which has been brought up various times found by
automated checkers. Make sure values are in u32 range.
* tag 'ieee802154-for-net-2021-11-24' of git://git.kernel.org/pub/scm/linux/kernel/git/sschmidt/wpan:
net: ieee802154: handle iftypes as u32
====================
Link: https://lore.kernel.org/r/20211124150934.3670248-1-stefan@datenfreihafen.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alex Deucher [Tue, 23 Nov 2021 15:44:48 +0000 (10:44 -0500)]
drm/amd/display: update bios scratch when setting backlight
Update the bios scratch register when updating the backlight
level. Some platforms apparently read this scratch register
and do additional operations in their hotkey handlers.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1518
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Alex Deucher [Tue, 23 Nov 2021 16:36:01 +0000 (11:36 -0500)]
drm/amdgpu/pm: fix powerplay OD interface
The overclocking interface currently appends data to a
string. Revert back to using sprintf().
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1774
Fixes:
6db0c87a0a8ee1 ("amdgpu/pm: Replace hwmgr smu usage of sprintf with sysfs_emit")
Acked-by: Evan Quan <evan.quan@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Lijo Lazar [Wed, 24 Nov 2021 11:26:38 +0000 (19:26 +0800)]
drm/amdgpu: Skip ASPM programming on aldebaran
There is no need for additional programming, keep the default settings.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Yang Wang [Wed, 24 Nov 2021 04:26:02 +0000 (12:26 +0800)]
drm/amdgpu: fix byteorder error in amdgpu discovery
fix some byteorder issues about amdgpu discovery.
This will result in running errors on the big end system. (e.g:MIPS)
Signed-off-by: Yang Wang <KevinYang.Wang@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>