drm/radeon/kms: Make GPU/CPU page size handling consistent in blit code (v2)

commit 003cefe0c238e683a29d2207dba945b508cd45b7 upstream.

The BO blit code inconsistenly handled the page size.  This wasn't
an issue on system with 4k pages since the GPU's page size is 4k as
well.  Switch the driver blit callbacks to take num pages in GPU
page units.

Fixes lemote mipsel systems using AMD rs780/rs880 chipsets.

v2: incorporate suggestions from Michel.

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

firewire: ohci: add no MSI quirk for O2Micro controller

commit f39aa30d7741f40ad964341e9243dbbd7f8ff057 upstream.

This fixes https://bugs.launchpad.net/ubuntu/+source/linux/+bug/801719 .

An O2Micro PCI Express FireWire controller,
"FireWire (IEEE 1394) [0c00]: O2 Micro, Inc. Device [1217:11f7] (rev 05)"
which is a combination device together with an SDHCI controller and some
sort of storage controller, misses SBP-2 status writes from an attached
FireWire HDD.  This problem goes away if MSI is disabled for this
FireWire controller.

The device reportedly does not require QUIRK_CYCLE_TIMER.

Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

ibmveth: Checksum offload is always disabled

commit 91aae1e5c407d4fc79f6983e6c6ba04756c004cb upstream.

Commit b9367bf3ee6d (net: ibmveth: convert to hw_features) reversed
a check in ibmveth_set_csum_offload that results in checksum offload
never being enabled.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

ibmveth: Fix issue with DMA mapping failure

commit b93da27f5234198433345e40b39ff59797bc6f6e upstream.

descs[].fields.address is 32bit which truncates any dma mapping
errors so dma_mapping_error() fails to catch it.

Use a dma_addr_t to do the comparison. With this patch I was able
to transfer many gigabytes of data with IOMMU fault injection set
at 10% probability.

Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

ibmveth: Fix DMA unmap error

commit 33a48ab105a75d37021e422a0a3283241099b142 upstream.

Commit 6e8ab30ec677 (ibmveth: Add scatter-gather support) introduced a
DMA mapping API inconsistency resulting in dma_unmap_page getting
called on memory mapped via dma_map_single. This was seen when
CONFIG_DMA_API_DEBUG was enabled. Fix up this API usage inconsistency.

Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Anton Blanchard <anton@samba.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

ALSA: pcm - fix race condition in wait_for_avail()

commit 763437a9e7737535b2fc72175ad4974048769be6 upstream.

wait_for_avail() in pcm_lib.c has a race in it (observed in practice by an
Intel validation group).

The function is supposed to return once space in the buffer has become
available, or if some timeout happens.  The entity that creates space (irq
handler of sound driver and some such) will do a wake up on a waitqueue
that this function registers for.

However there are two races in the existing code

1) If space became available between the caller noticing there was no
   space and this function actually sleeping, the wakeup is missed and the
   timeout condition will happen instead

2) If a wakeup happened but not sufficient space became available, the
   code will loop again and wait for more space.  However, if the second
   wake comes in prior to hitting the schedule_timeout_interruptible(), it
   will be missed, and potentially you'll wait out until the timeout
   happens.

The fix consists of using more careful setting of the current state (so
that if a wakeup happens in the main loop window, the schedule_timeout()
falls through) and by checking for available space prior to going into the
schedule_timeout() loop, but after being on the waitqueue and having the
state set to interruptible.

[tiwai: the following changes have been added to Arjan's original patch:
 - merged akpm's fix for waitqueue adding order into a single patch
 - reduction of duplicated code of avail check
]

Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

workqueue: lock cwq access in drain_workqueue

commit fa2563e41c3d6d6e8af437643981ed28ae0cb56d upstream.

Take cwq->gcwq->lock to avoid racing between drain_workqueue checking to
make sure the workqueues are empty and cwq_dec_nr_in_flight decrementing
and then incrementing nr_active when it activates a delayed work.

We discovered this when a corner case in one of our drivers resulted in
us trying to destroy a workqueue in which the remaining work would
always requeue itself again in the same workqueue.  We would hit this
race condition and trip the BUG_ON on workqueue.c:3080.

Signed-off-by: Thomas Tuttle <ttuttle@chromium.org>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

drivers/cpufreq/pcc-cpufreq.c: avoid NULL pointer dereference

commit e71f5cc402ecb42b407ae52add7b173bf1c53daa upstream.

per_cpu(processors, n) can be NULL, resulting in:

  Loading CPUFreq modules[  437.661360] BUG: unable to handle kernel NULL pointer dereference at (null)
  IP: [<ffffffffa0434314>] pcc_cpufreq_cpu_init+0x74/0x220 [pcc_cpufreq]

It's better to avoid the oops by failing the driver, and allowing the
system to boot.

Signed-off-by: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

drivers/leds/ledtrig-timer.c: fix broken sysfs delay handling

commit 7a5caabd090b8f7d782c40fc1c048d798f2b6fd7 upstream.

Fix regression introduced by commit 5ada28bf7675 ("led-class: always
implement blinking") which broke sysfs delay handling by not storing the
updated value.  Consequently it was only possible to set one of the delays
through the sysfs interface as the other delay was automatically restored
to it's default value.  Reading the parameters always gave the defaults.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Acked-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Richard Purdie <richard.purdie@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

mm: sync vmalloc address space page tables in alloc_vm_area()

commit 461ae488ecb125b140d7ea29ceeedbcce9327003 upstream.

Xen backend drivers (e.g., blkback and netback) would sometimes fail to
map grant pages into the vmalloc address space allocated with
alloc_vm_area().  The GNTTABOP_map_grant_ref would fail because Xen could
not find the page (in the L2 table) containing the PTEs it needed to
update.

(XEN) mm.c:3846:d0 Could not find L1 PTE for address fbb42000

netback and blkback were making the hypercall from a kernel thread where
task->active_mm != &init_mm and alloc_vm_area() was only updating the page
tables for init_mm.  The usual method of deferring the update to the page
tables of other processes (i.e., after taking a fault) doesn't work as a
fault cannot occur during the hypercall.

This would work on some systems depending on what else was using vmalloc.

Fix this by reverting ef691947d8a3 ("vmalloc: remove vmalloc_sync_all()
from alloc_vm_area()") and add a comment to explain why it's needed.

Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Cc: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Ian Campbell <Ian.Campbell@citrix.com>
Cc: Keir Fraser <keir.xen@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

restore pinning the victim dentry in vfs_rmdir()/vfs_rename_dir()

commit 1d2ef5901483004d74947bbf78d5146c24038fe7 upstream.

We used to get the victim pinned by dentry_unhash() prior to commit
64252c75a219 ("vfs: remove dget() from dentry_unhash()") and ->rmdir()
and ->rename() instances relied on that; most of them don't care, but
ones that used d_delete() themselves do.  As the result, we are getting
rmdir() oopses on NFS now.

Just grab the reference before locking the victim and drop it explicitly
after unlocking, same as vfs_rename_other() does.

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Tested-by: Simon Kirby <sim@hostway.ca>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

drm/radeon: Don't read from CP ring write pointer registers.

commit 87463ff83bcda210d8f0ae440bd64d1548f852e7 upstream.

Apparently this doesn't always work reliably, e.g. at resume time.

Just initialize to 0, so the ring is considered empty.

Tested with hibernation on Sumo and Cayman cards.

Should fix https://bugs.launchpad.net/ubuntu/+source/linux/+bug/820746/ .

Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

ALSA: HDA: Cirrus - fix "Surround Speaker" volume control name

commit 2e1210bc3d065a6e26ff5fef228a9a7e08921d2c upstream.

This patch fixes "Surround Speaker Playback Volume" being cut off.
(Commit b4dabfc452a10 was probably meant to fix this, but it fixed
only the "Switch" name, not the "Volume" name.)

Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

x86, iommu: Mark DMAR IRQ as non-threaded

commit 477694e71113fd0694b6bb0bcc2d006b8ac62691 upstream.

Mark this lowlevel IRQ handler as non-threaded. This prevents a boot
crash when "threadirqs" is on the kernel commandline. Also the
interrupt handler is handling hardware critical events which should
not be delayed into a thread.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

mac80211: fix missing sta_lock in __sta_info_destroy

commit 4bae7d976976fa52d345805ba686934cd548343e upstream.

Since my commit 34e895075e21be3e21e71d6317440d1ee7969ad0
("mac80211: allow station add/remove to sleep") there is
a race in mac80211 when it clears the TIM bit because a
sleeping station disconnected, the spinlock isn't held
around the relevant code any more. Use the right API to
acquire the spinlock correctly.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

rtlwifi: Fix problem when switching connections

commit bac2555c6d86387132930af4d14cb47c4dd3f4f7 upstream.

The driver fails to clear encryption keys making it impossible
to switch connections.

Signed-off-by: George <george0505@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

rtlwifi: rtl8192su: Fix problem connecting to HT-enabled AP

commit 3401dc6eba788ebc7c14ce51018d775b1c263399 upstream.

The driver fails to connect to 802.11n-enabled APs. The patch fixes
Bug #42262.

Signed-off-by: George <george0505@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

genirq: Make irq_shutdown() symmetric vs. irq_startup again

commit ed585a651681e822089087b426e6ebfb6d3d9873 upstream.

If an irq_chip provides .irq_shutdown(), but neither of .irq_disable() or
.irq_mask(), free_irq() crashes when jumping to NULL.
Fix this by only trying .irq_disable() and .irq_mask() if there's no
.irq_shutdown() provided.

This revives the symmetry with irq_startup(), which tries .irq_startup(),
.irq_enable(), and irq_unmask(), and makes it consistent with the comment for
irq_chip.irq_shutdown() in <linux/irq.h>, which says:

 * @irq_shutdown: shut down the interrupt (defaults to ->disable if NULL)

This is also how __free_irq() behaved before the big overhaul, cfr. e.g.
3b56f0585fd4c02d047dc406668cb40159b2d340 ("genirq: Remove bogus conditional"),
where the core interrupt code always overrode .irq_shutdown() to
.irq_disable() if .irq_shutdown() was NULL.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: linux-m68k@lists.linux-m68k.org
Link: http://lkml.kernel.org/r/1315742394-16036-2-git-send-email-geert@linux-m68k.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

mfd: Make omap-usb-host TLL mode work again

commit e600cffe618ff0da29ae1f8b8d3824ce0e2409fc upstream.

This code section seems to have been accidentally copy pasted.
It causes incorrect bits to be set up in the TLL_CHANNEL_CONF
register and prevents the TLL mode from working correctly.

Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Keshava Munegowda <keshava_mgowda@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

mfd: Fix initialisation of tps65910 interrupts

commit fa948761e685fb03823b3029e5b6bdb52229d6ce upstream.

Fix regression introduced by commit
a2974732ca7614aaf0baf9d6dd3ad893d50ce1c5 (TPS65911: Add new irq
definitions) which caused irq_num to be incorrectly set for tps65910.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Acked-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

mfd: Fix value of WM8994_CONFIGURE_GPIO

commit 8efcc57dedfebc99c3cd39564e3fc47cd1a24b75 upstream.

This needs to be an out of band value for the register and on this device
registers are 16 bit so we must shift left one to the 17th bit.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

ASoC: Blackfin: bf5xx-ad193x: Fix codec device name

commit c5d2e650bd805a00ff9af537d5b5dede598a198c upstream.

Fix the codec_name field of the dai_link to match the actual device name
of the codec. Otherwise the card won't be instantiated.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

ASoC: Fix reporting of partial jack updates

commit 747da0f80e566500421bd7760b2e050fea3fde5e upstream.

We need to report the entire jack state to the core jack code, not just
the bits that were being updated by the caller, otherwise the status
reported by other detection methods will be omitted from the state seen
by userspace.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

e1000: Fix driver to be used on PA RISC C8000 workstations

commit e2faeec2de9e2c73958e6ea6065dde1e8cd6f3a2 upstream.

The checksum field in the EEPROM on HPPA is really not a
checksum but a signature (0x16d6).  So allow 0x16d6 as the
matching checksum on HPPA systems.

This issue is present on longterm/stable kernels, I have
verified that this patch is applicable back to at least
2.6.32.y kernels.

v2- changed ifdef to use CONFIG_PARISC instead of __hppa__

CC: Guy Martin <gmsoft@tuxicoman.be>
CC: Rolf Eike Beer <eike-kernel@sf-tec.de>
CC: Matt Turner <mattst88@gmail.com>
Reported-by: Mikulas Patocka <mikulas@artax.kerlin.mff.cuni.cz>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

ath9k_hw: fix calibration on 5 ghz

commit 0e4660cbe51276e86dbdab17228733dbcdb49249 upstream.

ADC calibrations cannot run on 5 GHz with fast clock enabled. They
need to be disabled, otherwise they'll hang and IQ mismatch calibration
will not be run either.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Adrian Chadd <adrian@freebsd.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

acpica: ACPI_MAX_SLEEP should be 2 sec, not 20

commit b33c25d6a62ac253caabda2b5f43258abff451c0 upstream.

This limit is a workaround for AML that sleeps too long,
but the workaround didn't work b/c of a typo.

https://bugzilla.kernel.org/show_bug.cgi?id=13195

Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

iwlegacy: fix BUG_ON(info->control.rates[0].idx < 0)

commit 7c2510120e9b43b0caf32c3786a6ab831f7d9e87 upstream.

When trying to connect to 5GHz we can provide negative index to
mac80211 what trigger BUG_ON. Reason of iwl-3945-rs malfunction
on 5GHz is unknown and needs further investigation. For now, to
do not trigger a bug, correct value and just print WARNING.

Address bug:
https://bugzilla.redhat.com/show_bug.cgi?id=730653

Reported-and-tested-by: Jan Teichmann <jan.teichmann@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

qla2xxx: Correct inadvertent loop state transitions during port-update handling.

commit 58b48576966ed0afd3f63ef17480ec12748a7119 upstream.

Transitioning to a LOOP_UPDATE loop-state could cause the driver
to miss normal link/target processing.  LOOP_UPDATE is a crufty
artifact leftover from at time the driver performed it's own
internal command-queuing.  Safely remove this state.

Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

hpsa: fix physical device lun and target numbering problem

commit 01350d05539d1c95ef3568d062d864ab76ae7670 upstream.

If a physical device exposed to the OS by hpsa
is replaced (e.g. one hot plug tape drive is replaced
by another, or a tape drive is placed into "OBDR" mode
in which it acts like a CD-ROM device) and a rescan is
initiated, the replaced device will be added to the
SCSI midlayer with target and lun numbers set to -1.
After that, a panic is likely to ensue.  When a physical
device is replaced, the lun and target number should be
preserved.

Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

hpsa: fix problem that OBDR devices are not detected

commit 0b0e1d6cbcc8627970e0399df8f06edd690ec7d9 upstream.

The test to detect OBDR ("One Button Disaster Recovery")
cd-rom devices was comparing against uninitialized data.

Fixed by moving the test for the device to where the
inquiry data is collected, and uninitialized variable
altogether as it wasn't really being used.

Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

ASoC: MPC5200: replace of_device with platform_device

commit 3bdf28feafc52864bd7f17b39deec64833a89d19 upstream.

'struct of_device' no longer exists, and its functionality has been merged
into platform_device.  Update the MPC5200 audio DMA driver (mpc5200_dma)
accordingly.  This fixes a build break.

Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

isci: fix 32-bit operation when CONFIG_HIGHMEM64G=n

commit ee33e2b771f9e9e4aaba2bb2ace7b727fe451a8b upstream.

The unsolicited frame control infrastructure requires a table of dma
addresses for the hardware to lookup the frame buffer location by an
index.  The hardware expects the elements of this table to be 64-bit
quantities, so we cannot reference these elements as dma_addr_t.  All
unsolicited frame protocols are affected, particularly SATA-PIO and SMP
which prevented direct-attached SATA drives and expander-attached drives
to not be discovered.

Reported-by: Jacek Danecki <jacek.danecki@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

isci: fix sata response handling

commit 1a878284473284f9577d44babf16d87152a05c33 upstream.

A bug (likely copy/paste) that has been carried from the original
implementation.  The unsolicited frame handling structure returns the
d2h fis in the isci_request.stp.rsp buffer.

Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

fs/9p: Use protocol-defined value for lock/getlock 'type' field.

commit 51b8b4fb32271d39fbdd760397406177b2b0fd36 upstream.

Signed-off-by: Jim Garlick <garlick@llnl.gov>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Harsh Prateek Bora <harsh@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

fs/9p: Always ask new inode in lookup for cache mode disabled

commit 73f507171cfa407b19f254aef95cbb058c8180cf upstream.

This make sure we don't end up reusing the unlinked inode object.
The ideal way is to use inode i_generation. But i_generation is
not available in userspace always.

Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

net/9p: Fix kernel crash with msize 512K

commit b49d8b5d7007a673796f3f99688b46931293873e upstream.

With msize equal to 512K (PAGE_SIZE * VIRTQUEUE_NUM), we hit multiple
crashes. This patch fix those.

Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

fs/9p: Add OS dependent open flags in 9p protocol

commit f88657ce3f9713a0c62101dffb0e972a979e77b9 upstream.

Some of the flags are OS/arch dependent we add a 9p
protocol value which maps to asm-generic/fcntl.h values in Linux
Based on the original patch from Venkateswararao Jujjuri <jvrao@linux.vnet.ibm.com>

[extra comments from author as to why this needs to go to stable:

Earlier for different operation such as open we used the values of open
flag as defined by the OS.  But some of these flags such as O_DIRECT are
arch dependent. So if we have the 9p client and server running on
different architectures, we end up with client sending client
architecture value of these open flag and server will try to map these
values to what its architecture states. For ex: O_DIRECT on a x86 client
maps to

#define O_DIRECT        00040000

Where as on sparc server it will maps to

#define O_DIRECT        0x100000

Hence we need to map these open flags to OS/arch independent flag
values.  Getting these changes to an early version of kernel ensures us
that we work with different combination of client and server. We should
ideally backport this patch to all possible kernel version.]

Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Harsh Prateek Bora <harsh@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

fs/9p: Don't update file type when updating file attributes

commit 45089142b1497dab2327d60f6c71c40766fc3ea4 upstream.

We should only update attributes that we can change on stat2inode.
Also do file type initialization in v9fs_init_inode.

Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

fs/9p: Add fid before dentry instantiation

commit 5441ae5eb3614d3c28f77073370738a2820c88e4 upstream.

d_instantiate marks the dentry positive. So a parallel lookup and mkdir of
the directory can find dentry that doesn't have fid attached. This can result
in both the code path doing v9fs_fid_add which results in v9fs_dentry leak.

Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

ACPICA: Do not repair _TSS return package if _PSS is present

commit 8f9c91273e36e5762c617c23e4fd48d5172e0dac upstream.

We can only sort the _TSS return package if there is no _PSS
in the same scope. This is because if _PSS is present, the ACPI
specification dictates that the _TSS Power Dissipation field is
to be ignored, and therefore some BIOSs leave garbage values in
the _TSS Power field(s).  In this case, it is best to just return
the _TSS package as-is.

Reported-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

iommu/amd: Make sure iommu->need_sync contains correct value

commit f1ca1512e765337a7c09eb875eedef8ea4e07654 upstream.

The value is only set to true but never set back to false,
which causes to many completion-wait commands to be sent to
hardware. Fix it with this patch.

Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

iommu/amd: Don't take domain->lock recursivly

commit e33acde91140f1809952d1c135c36feb66a51887 upstream.

The domain_flush_devices() function takes the domain->lock.
But this function is only called from update_domain() which
itself is already called unter the domain->lock. This causes
a deadlock situation when the dma-address-space of a domain
grows larger than 1GB.

Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

irda: fix smsc-ircc2 section mismatch warning

commit f470e5ae34d68880a38aa79ee5c102ebc2a1aef6 upstream.

Fix section mismatch warning:

WARNING: drivers/net/irda/smsc-ircc2.o(.devinit.text+0x1a7): Section mismatch in reference from the function smsc_ircc_pnp_probe() to the function .init.text:smsc_ircc_open()

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

9p: close ACL leaks

commit 1ec95bf34d976b38897d1977b155a544d77b05e7 upstream.

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

net/9p: Fix the msize calculation.

commit c9ffb05ca5b5098d6ea468c909dd384d90da7d54 upstream.

msize represents the maximum PDU size that includes P9_IOHDRSZ.

Signed-off-by: Venkateswararao Jujjuri "<jvrao@linux.vnet.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

fs/9p: Always ask new inode in create

commit ed80fcfac2565fa866d93ba14f0e75de17a8223e upstream.

This make sure we don't end up reusing the unlinked inode object.
The ideal way is to use inode i_generation. But i_generation is
not available in userspace always.

Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

fs/9p: Fix invalid mount options/args

commit a2dd43bb0d7b9ce28f8a39254c25840c0730498e upstream.

Without this fix, if any invalid mount options/args are passed while mouting
the 9p fs, no error (-EINVAL) is returned and default arg value is assigned.

This fix returns -EINVAL when an invalid arguement is found while parsing
mount options.

Signed-off-by: Prem Karat <prem.karat@linux.vnet.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

fs/9p: When doing inode lookup compare qid details and inode mode bits.

commit fd2421f54423f307ecd31bdebdca6bc317e0c492 upstream.

This make sure we don't use wrong inode from the inode hash. The inode number
of the file deleted is reused by the next file system object created
and if we only use inode number for inode hash lookup we could end up
with wrong struct inode.

Also compare inode generation number. Not all Linux file system provide
st_gen in userspace. So it could be 0;

Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

fs/9p: Fid is not valid after a failed clunk.

commit 5034990e28efb2d232ee82443a9edd62defd17ba upstream.

free the fid even in case of failed clunk.

Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

VirtIO can transfer VIRTQUEUE_NUM of pages.

commit 7f781679dd596c8abde8336b4d0d166d6a4aad04 upstream.

Signed-off-by: Venkateswararao Jujjuri "<jvrao@linux.vnet.ibm.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Fix the size of receive buffer packing onto VirtIO ring.

commit 114e6f3a5ede73d5b56e145f04680c61c3dd67c4 upstream.

Signed-off-by: Venkateswararao Jujjuri "<jvrao@linux.vnet.ibm.com>
Reviewed-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

net/9p: fix client code to fail more gracefully on protocol error

commit b85f7d92d7bd7e3298159e8b1eed8cb8cbbb0348 upstream.

There was a BUG_ON to protect against a bad id which could be dealt with
more gracefully.

Reported-by: Natalie Orlin <norlin@us.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

vp7045: fix buffer setup

commit fc61ccd35fd59d5362d37c8bf9c0526c85086c84 upstream.

dvb_usb_device_init calls the frontend_attach method of this driver which
uses vp7045_usb_ob. In order to have a buffer ready in vp7045_usb_op, it has to
be allocated before that happens.

Luckily we can use the whole private data as the buffer as it gets separately
allocated on the heap via kzalloc in dvb_usb_device_init and is thus apt for
use via usb_control_msg.

This fixes a
BUG: unable to handle kernel paging request at 0000000000001e78

reported by Tino Keitel and diagnosed by Dan Carpenter.

Tested-by: Tino Keitel <tino.keitel@tikei.de>
Signed-off-by: Florian Mickler <florian@mickler.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

nuvoton-cir: simplify raw IR sample handling

commit de4ed0c111ed078b8729a5cc49c23197740f5bad upstream.

The nuvoton-cir driver was storing up consecutive pulse-pulse and
space-space samples internally, for no good reason, since
ir_raw_event_store_with_filter() already merges back to back like
samples types for us. This should also fix a regression introduced late
in 3.0 that related to a timeout change, which actually becomes correct
when coupled with this change. Tested with RC6 and RC5 on my own
nuvoton-cir hardware atop vanilla 3.0.0, after verifying quirky
behavior in 3.0 due to the timeout change.

Reported-by: Stephan Raue <sraue@openelec.tv>
CC: Stephan Raue <sraue@openelec.tv>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

md: Fix handling for devices from 2TB to 4TB in 0.90 metadata.

commit 27a7b260f71439c40546b43588448faac01adb93 upstream.

0.90 metadata uses an unsigned 32bit number to count the number of
kilobytes used from each device.
This should allow up to 4TB per device.
However we multiply this by 2 (to get sectors) before casting to a
larger type, so sizes above 2TB get truncated.

Also we allow rdev->sectors to be larger than 4TB, so it is possible
for the array to be resized larger than the metadata can handle.
So make sure rdev->sectors never exceeds 4TB when 0.90 metadata is in
used.

Also the sanity check at the end of super_90_load should include level
1 as it used ->size too. (RAID0 and Linear don't use ->size at all).

Reported-by: Pim Zandbergen <P.Zandbergen@macroscoop.nl>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Avoid dereferencing a 'request_queue' after last close.

commit 94007751bb02797ba87bac7aacee2731ac2039a3 upstream.

On the last close of an 'md' device which as been stopped, the device
is destroyed and in particular the request_queue is freed.  The free
is done in a separate thread so it might happen a short time later.

__blkdev_put calls bdev_inode_switch_bdi *after* ->release has been
called.

Since commit f758eeabeb96f878c860e8f110f94ec8820822a9
bdev_inode_switch_bdi will dereference the 'old' bdi, which lives
inside a request_queue, to get a spin lock.  This causes the last
close on an md device to sometime take a spin_lock which lives in
freed memory - which results in an oops.

So move the called to bdev_inode_switch_bdi before the call to
->release.

Cc: Christoph Hellwig <hch@lst.de>
Cc: Hugh Dickins <hughd@google.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Acked-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

drm/nouveau: properly handle allocation failure in nouveau_sgdma_populate

commit 17c8b960930da3599e47801a54ac0ea1070545d2 upstream.

Not cleaning after alloc failure would result in crash on destroy,
because nouveau_sgdma_clear assumes "ttm_alloced" to be not null when
"pages" is not null.

Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

ARM: davinci: fix cache flush build error

commit 897a6a1a14837d6d582bfd1fd7aba00be44b6469 upstream.

The TNET variant of DaVinci compiles some code that it shares
with other DaVinci variants, however it has a V6 CPU rather than
an ARM926T, thus the hardcoded call to arm926_flush_kern_cache_all()
in sleep.S will obviously fail, and we need to build with the
v6_flush_kern_cache_all() call instead. This was triggered by
manually altering the DaVinci config to build the TNET version.

Cc: Dave Martin <dave.martin@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

ARM: davinci: da850 EVM: read mac address from SPI flash

commit 810198bc9c109489dfadc57131c5183ce6ad2d7d upstream.

DA850/OMAP-L138 EMAC driver uses random mac address instead of
a fixed one because the mac address is not stuffed into EMAC
platform data.

This patch provides a function which reads the mac address
stored in SPI flash (registered as MTD device) and populates the
EMAC platform data. The function which reads the mac address is
registered as a callback which gets called upon addition of MTD
device.

NOTE: In case the MAC address stored in SPI flash is erased, follow
the instructions at [1] to restore it.

[1] http://processors.wiki.ti.com/index.php/GSG:_OMAP-L138_DVEVM_Additional_Procedures#Restoring_MAC_address_on_SPI_Flash

Modifications in v2:
Guarded registering the mtd_notifier only when MTD is enabled.
Earlier this was handled using mtd_has_partitions() call, but
this has been removed in Linux v3.0.

Modifications in v3:
a. Guarded da850_evm_m25p80_notify_add() function and
   da850evm_spi_notifier structure with CONFIG_MTD macros.
b. Renamed da850_evm_register_mtd_user() function to
   da850_evm_setup_mac_addr() and removed the struct mtd_notifier
   argument to this function.
c. Passed the da850evm_spi_notifier structure to register_mtd_user()
   function.

Modifications in v4:
Moved the da850_evm_setup_mac_addr() function within the first
CONFIG_MTD ifdef construct.

Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

ARM: 7081/1: mach-integrator: fix the clocksource

commit bb9ea77846620ed2b37e74c852d72c7a476b248c upstream.

I was intrigued by the fact that the clock stood still on
the Integrator, but it wasn't strange at all, because the
timer was set up all wrong and probably has been for a
while. With this patch the clock starts ticking again:
make the timer periodic (reload), |= on the divisor bit
and load the timer before starting it.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

hwmon: (max16065) Fix current calculation

commit ff71c182f461da5ae9d2d65f8a63f5a9193b9be1 upstream.

Current calculation is completely wrong. Add missing brackets to fix it.

Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

xen/smp: Warn user why they keel over - nosmp or noapic and what to use instead.

commit ed467e69f16e6b480e2face7bc5963834d025f91 upstream.

We have hit a couple of customer bugs where they would like to
use those parameters to run an UP kernel - but both of those
options turn of important sources of interrupt information so
we end up not being able to boot. The correct way is to
pass in 'dom0_max_vcpus=1' on the Xen hypervisor line and
the kernel will patch itself to be a UP kernel.

Fixes bug: http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=637308

Acked-by: Ian Campbell <Ian.Campbell@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

xen: x86_32: do not enable iterrupts when returning from exception in interrupt context

commit d198d499148a0c64a41b3aba9e7dd43772832b91 upstream.

If vmalloc page_fault happens inside of interrupt handler with interrupts
disabled then on exit path from exception handler when there is no pending
interrupts, the following code (arch/x86/xen/xen-asm_32.S:112):

cmpw $0x0001, XEN_vcpu_info_pending(%eax)
sete XEN_vcpu_info_mask(%eax)

will enable interrupts even if they has been previously disabled according to
eflags from the bounce frame (arch/x86/xen/xen-asm_32.S:99)

testb $X86_EFLAGS_IF>>8, 8+1+ESP_OFFSET(%esp)
setz XEN_vcpu_info_mask(%eax)

Solution is in setting XEN_vcpu_info_mask only when it should be set
according to
cmpw $0x0001, XEN_vcpu_info_pending(%eax)
but not clearing it if there isn't any pending events.

Reproducer for bug is attached to RHBZ 707552

Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

mmc: sdhci-s3c: Fix mmc card I/O problem

commit 49bb1e619568ec84785ceb366f07db2a6f0b64cc upstream.

This patch fixes the problem in sdhci-s3c host driver for Samsung Soc's.
During the card identification stage the mmc core driver enumerates for
the best bus width in combination with the highest available data rate.
It starts enumerating from the highest bus width (8) to lowest width (1).

In case of few MMC cards the 4-bit bus enumeration fails and tries
the 1-bit bus enumeration. When switched to 1-bit bus mode the host driver
has to clear the previous bus width setting and apply the new setting.

The current patch will clear the previous bus mode and apply the new
mode setting.

Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

mmc: core: use non-reentrant workqueue for clock gating

commit 50a50f9248497484c678631a9c1a719f1aaeab79 upstream.

The default multithread workqueue can cause the same work to be executed
concurrently on a different CPUs. This isn't really suitable for clock
gating as it might already gated the clock and gating it twice results both
host->clk_old and host->ios.clock to be set to 0.

To prevent this from happening we use system_nrt_wq instead.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

mmc: core: prevent aggressive clock gating racing with ios updates

commit 778e277cb82411c9002ca28ccbd216c4d9eb9158 upstream.

We have seen at least two different races when clock gating kicks in in a
middle of ios structure update.

First one happens when ios->clock is changed outside of aggressive clock
gating framework, for example via mmc_set_clock(). The race might happen
when we run following code:

mmc_set_ios():
...
if (ios->clock > 0)
mmc_set_ungated(host);

Now if gating kicks in right after the condition check we end up setting
host->clk_gated to false even though we have just gated the clock. Next
time a request is started we try to ungate and restore the clock in
mmc_host_clk_hold(). However since we have host->clk_gated set to false the
original clock is not restored.

This eventually will cause the host controller to hang since its clock is
disabled while we are trying to issue a request. For example on Intel
Medfield platform we see:

[   13.818610] mmc2: Timeout waiting for hardware interrupt.
[   13.818698] sdhci: =========== REGISTER DUMP (mmc2)===========
[   13.818753] sdhci: Sys addr: 0x00000000 | Version:  0x00008901
[   13.818804] sdhci: Blk size: 0x00000000 | Blk cnt:  0x00000000
[   13.818853] sdhci: Argument: 0x00000000 | Trn mode: 0x00000000
[   13.818903] sdhci: Present:  0x1fff0000 | Host ctl: 0x00000001
[   13.818951] sdhci: Power:    0x0000000d | Blk gap:  0x00000000
[   13.819000] sdhci: Wake-up:  0x00000000 | Clock:    0x00000000
[   13.819049] sdhci: Timeout:  0x00000000 | Int stat: 0x00000000
[   13.819098] sdhci: Int enab: 0x00ff00c3 | Sig enab: 0x00ff00c3
[   13.819147] sdhci: AC12 err: 0x00000000 | Slot int: 0x00000000
[   13.819196] sdhci: Caps:     0x6bee32b2 | Caps_1:   0x00000000
[   13.819245] sdhci: Cmd:      0x00000000 | Max curr: 0x00000000
[   13.819292] sdhci: Host ctl2: 0x00000000
[   13.819331] sdhci: ADMA Err: 0x00000000 | ADMA Ptr: 0x00000000
[   13.819377] sdhci: ===========================================
[   13.919605] mmc2: Reset 0x2 never completed.

and it never recovers.

Second race might happen while running mmc_power_off():

static void mmc_power_off(struct mmc_host *host)
{
host->ios.clock = 0;
host->ios.vdd = 0;

[ clock gating kicks in here ]

/*
 * Reset ocr mask to be the highest possible voltage supported for
 * this mmc host. This value will be used at next power up.
 */
host->ocr = 1 << (fls(host->ocr_avail) - 1);

if (!mmc_host_is_spi(host)) {
host->ios.bus_mode = MMC_BUSMODE_OPENDRAIN;
host->ios.chip_select = MMC_CS_DONTCARE;
}
host->ios.power_mode = MMC_POWER_OFF;
host->ios.bus_width = MMC_BUS_WIDTH_1;
host->ios.timing = MMC_TIMING_LEGACY;
mmc_set_ios(host);
}

If the clock gating worker kicks in while we are only partially updated the
ios structure the host controller gets incomplete ios and might not work as
supposed. Again on Intel Medfield platform we get:

[    4.185349] kernel BUG at drivers/mmc/host/sdhci.c:1155!
[    4.185422] invalid opcode: 0000 [#1] PREEMPT SMP
[    4.185509] Modules linked in:
[    4.185565]
[    4.185608] Pid: 4, comm: kworker/0:0 Not tainted 3.0.0+ #240 Intel Corporation Medfield/iCDKA
[    4.185742] EIP: 0060:[<c136364e>] EFLAGS: 00010083 CPU: 0
[    4.185827] EIP is at sdhci_set_power+0x3e/0xd0
[    4.185891] EAX: f5ff98e0 EBX: f5ff98e0 ECX: 00000000 EDX: 00000001
[    4.185970] ESI: f5ff977c EDI: f5ff9904 EBP: f644fe98 ESP: f644fe94
[    4.186049]  DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
[    4.186125] Process kworker/0:0 (pid: 4, ti=f644e000 task=f644c0e0 task.ti=f644e000)
[    4.186219] Stack:
[    4.186257]  f5ff98e0 f644feb0 c1365173 00000282 f5ff9460 f5ff96e0 f5ff96e0 f644feec
[    4.186418]  c1355bd8 f644c0e0 c1499c3d f5ff96e0 f644fed4 00000006 f5ff96e0 00000286
[    4.186579]  f644fedc c107922b f644feec 00000286 f5ff9460 f5ff9700 f644ff10 c135839e
[    4.186739] Call Trace:
[    4.186802]  [<c1365173>] sdhci_set_ios+0x1c3/0x340
[    4.186883]  [<c1355bd8>] mmc_gate_clock+0x68/0x120
[    4.186963]  [<c1499c3d>] ? _raw_spin_unlock_irqrestore+0x4d/0x60
[    4.187052]  [<c107922b>] ? trace_hardirqs_on+0xb/0x10
[    4.187134]  [<c135839e>] mmc_host_clk_gate_delayed+0xbe/0x130
[    4.187219]  [<c105ec09>] ? process_one_work+0xf9/0x5b0
[    4.187300]  [<c135841d>] mmc_host_clk_gate_work+0xd/0x10
[    4.187379]  [<c105ec82>] process_one_work+0x172/0x5b0
[    4.187457]  [<c105ec09>] ? process_one_work+0xf9/0x5b0
[    4.187538]  [<c1358410>] ? mmc_host_clk_gate_delayed+0x130/0x130
[    4.187625]  [<c105f3c8>] worker_thread+0x118/0x330
[    4.187700]  [<c1496cee>] ? preempt_schedule+0x2e/0x50
[    4.187779]  [<c105f2b0>] ? rescuer_thread+0x1f0/0x1f0
[    4.187857]  [<c1062cf4>] kthread+0x74/0x80
[    4.187931]  [<c1062c80>] ? __init_kthread_worker+0x60/0x60
[    4.188015]  [<c149acfa>] kernel_thread_helper+0x6/0xd
[    4.188079] Code: 81 fa 00 00 04 00 0f 84 a7 00 00 00 7f 21 81 fa 80 00 00 00 0f 84 92 00 00 00 81 fa 00 00 0
[    4.188780] EIP: [<c136364e>] sdhci_set_power+0x3e/0xd0 SS:ESP 0068:f644fe94
[    4.188898] ---[ end trace a7b23eecc71777e4 ]---

This BUG() comes from the fact that ios.power_mode was still in previous
value (MMC_POWER_ON) and ios.vdd was set to zero.

We prevent these by inhibiting the clock gating while we update the ios
structure.

Both problems can be reproduced by simply running the device in a reboot
loop.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

mmc: rename mmc_host_clk_{ungate|gate} to mmc_host_clk_{hold|release}

commit 08c14071fda4e69abb9d5b1566651cd092b158d3 upstream.

As per suggestion by Linus Walleij:

  > If you think the names of the functions are confusing then
  > you may rename them, say like this:
  >
  > mmc_host_clk_ungate() -> mmc_host_clk_hold()
  > mmc_host_clk_gate() -> mmc_host_clk_release()
  >
  > Which would make the usecases more clear

(This is CC'd to stable@ because the next two patches, which fix
observable races, depend on it.)

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

x86, perf: Check that current->mm is alive before getting user callchain

commit 20afc60f892d285fde179ead4b24e6a7938c2f1b upstream.

An event may occur when an mm is already released.

I added an event in dequeue_entity() and caught a panic with
the following backtrace:

[  434.421110] BUG: unable to handle kernel NULL pointer dereference at 0000000000000050
[  434.421258] IP: [<ffffffff810464ac>] __get_user_pages_fast+0x9c/0x120
...
[  434.421258] Call Trace:
[  434.421258]  [<ffffffff8101ae81>] copy_from_user_nmi+0x51/0xf0
[  434.421258]  [<ffffffff8109a0d5>] ? sched_clock_local+0x25/0x90
[  434.421258]  [<ffffffff8101b048>] perf_callchain_user+0x128/0x170
[  434.421258]  [<ffffffff811154cd>] ? __perf_event_header__init_id+0xed/0x100
[  434.421258]  [<ffffffff81116690>] perf_prepare_sample+0x200/0x280
[  434.421258]  [<ffffffff81118da8>] __perf_event_overflow+0x1b8/0x290
[  434.421258]  [<ffffffff81065240>] ? tg_shares_up+0x0/0x670
[  434.421258]  [<ffffffff8104fe1a>] ? walk_tg_tree+0x6a/0xb0
[  434.421258]  [<ffffffff81118f44>] perf_swevent_overflow+0xc4/0xf0
[  434.421258]  [<ffffffff81119150>] do_perf_sw_event+0x1e0/0x250
[  434.421258]  [<ffffffff81119204>] perf_tp_event+0x44/0x70
[  434.421258]  [<ffffffff8105701f>] ftrace_profile_sched_block+0xdf/0x110
[  434.421258]  [<ffffffff8106121d>] dequeue_entity+0x2ad/0x2d0
[  434.421258]  [<ffffffff810614ec>] dequeue_task_fair+0x1c/0x60
[  434.421258]  [<ffffffff8105818a>] dequeue_task+0x9a/0xb0
[  434.421258]  [<ffffffff810581e2>] deactivate_task+0x42/0xe0
[  434.421258]  [<ffffffff814bc019>] thread_return+0x191/0x808
[  434.421258]  [<ffffffff81098a44>] ? switch_task_namespaces+0x24/0x60
[  434.421258]  [<ffffffff8106f4c4>] do_exit+0x464/0x910
[  434.421258]  [<ffffffff8106f9c8>] do_group_exit+0x58/0xd0
[  434.421258]  [<ffffffff8106fa57>] sys_exit_group+0x17/0x20
[  434.421258]  [<ffffffff8100b202>] system_call_fastpath+0x16/0x1b

Signed-off-by: Andrey Vagin <avagin@openvz.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1314693156-24131-1-git-send-email-avagin@openvz.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

sched: Fix a memory leak in __sdt_free()

commit feff8fa0075bdfd43c841e9d689ed81adda988d6 upstream.

This patch fixes the following memory leak:

unreferenced object 0xffff880107266800 (size 512):
  comm "sched-powersave", pid 3718, jiffies 4323097853 (age 27495.450s)
  hex dump (first 32 bytes):
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  backtrace:
    [<ffffffff81133940>] create_object+0x187/0x28b
    [<ffffffff814ac103>] kmemleak_alloc+0x73/0x98
    [<ffffffff811232ba>] __kmalloc_node+0x104/0x159
    [<ffffffff81044b98>] kzalloc_node.clone.97+0x15/0x17
    [<ffffffff8104cb90>] build_sched_domains+0xb7/0x7f3
    [<ffffffff8104d4df>] partition_sched_domains+0x1db/0x24a
    [<ffffffff8109ee4a>] do_rebuild_sched_domains+0x3b/0x47
    [<ffffffff810a00c7>] rebuild_sched_domains+0x10/0x12
    [<ffffffff8104d5ba>] sched_power_savings_store+0x6c/0x7b
    [<ffffffff8104d5df>] sched_mc_power_savings_store+0x16/0x18
    [<ffffffff8131322c>] sysdev_class_store+0x20/0x22
    [<ffffffff81193876>] sysfs_write_file+0x108/0x144
    [<ffffffff81135b10>] vfs_write+0xaf/0x102
    [<ffffffff81135d23>] sys_write+0x4d/0x74
    [<ffffffff814c8a42>] system_call_fastpath+0x16/0x1b
    [<ffffffffffffffff>] 0xffffffffffffffff

Signed-off-by: WANG Cong <amwang@redhat.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1313671017-4112-1-git-send-email-amwang@redhat.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

sched: Move blk_schedule_flush_plug() out of __schedule()

commit 9c40cef2b799f9b5e7fa5de4d2ad3a0168ba118c upstream.

There is no real reason to run blk_schedule_flush_plug() with
interrupts and preemption disabled.

Move it into schedule() and call it when the task is going voluntarily
to sleep. There might be false positives when the task is woken
between that call and actually scheduling, but that's not really
different from being woken immediately after switching away.

This fixes a deadlock in the scheduler where the
blk_schedule_flush_plug() callchain enables interrupts and thereby
allows a wakeup to happen of the task that's going to sleep.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/n/tip-dwfxtra7yg1b5r65m32ywtct@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

sched: Separate the scheduler entry for preemption

commit c259e01a1ec90063042f758e409cd26b2a0963c8 upstream.

Block-IO and workqueues call into notifier functions from the
scheduler core code with interrupts and preemption disabled. These
calls should be made before entering the scheduler core.

To simplify this, separate the scheduler core code into
__schedule(). __schedule() is directly called from the places which
set PREEMPT_ACTIVE and from schedule(). This allows us to add the work
checks into schedule(), so they are only called when a task voluntary
goes to sleep.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/20110622174918.813258321@linutronix.de
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

rtc: Fix RTC PIE frequency limit

commit 938f97bcf1bdd1b681d5d14d1d7117a2e22d4434 upstream.

Thomas earlier submitted a fix to limit the RTC PIE freq, but
picked 5000Hz out of the air. Willy noticed that we should
instead use the 8192Hz max from the rtc man documentation.

Cc: Willy Tarreau <w@1wt.eu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

alarmtimers: Avoid possible denial of service with high freq periodic timers

commit 6af7e471e5a7746b8024d70b4363d3dfe41d36b8 upstream.

Its possible to jam up the alarm timers by setting very small interval
timers, which will cause the alarmtimer subsystem to spend all of its time
firing and restarting timers. This can effectivly lock up a box.

A deeper fix is needed, closely mimicking the hrtimer code, but for now
just cap the interval to 100us to avoid userland hanging the system.

CC: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

alarmtimers: Memset itimerspec passed into alarm_timer_get

commit ea7802f630d356acaf66b3c0b28c00a945fc35dc upstream.

Following common_timer_get, zero out the itimerspec passed in.

CC: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

alarmtimers: Avoid possible null pointer traversal

commit 971c90bfa2f0b4fe52d6d9002178d547706f1343 upstream.

We don't check if old_setting is non null before assigning it, so
correct this.

CC: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

MXC: iomux-v3: correct NO_PAD_CTRL definition

commit 425933b30b0ccfac58065bca6c853ea627443cdf upstream.

iomux-v3.c uses NO_PAD_CTRL as a 32 bit value
so it should not be shifted left by MUX_PAD_CTRL_SHIFT(41)

Previously, anything requesting NO_PAD_CTRL would get
their pad control register set to 0.

Since it is a pad control mask, place it with the other mask values.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Lothar Waßmann <LW@KARO-electronics.de>
Tested-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

igb: fix WOL on second port of i350 device

commit 6d337dce664b6872ddf1655f6b1fcab76ce35b08 upstream.

This patch fixes a problem where WOL would fail on second port of i350
device.

Reported-by: Martin Wilck <martin.wilck@ts.fujitsu.com>
Reported-by: Stefan Assmann<sassmann@redhat.com>
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

mm: page allocator: reconsider zones for allocation after direct reclaim

commit 76d3fbf8fbf6cc78ceb63549e0e0c5bc8a88f838 upstream.

With zone_reclaim_mode enabled, it's possible for zones to be considered
full in the zonelist_cache so they are skipped in the future.  If the
process enters direct reclaim, the ZLC may still consider zones to be full
even after reclaiming pages.  Reconsider all zones for allocation if
direct reclaim returns successfully.

Signed-off-by: Mel Gorman <mgorman@suse.de>
Cc: Minchan Kim <minchan.kim@gmail.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Christoph Lameter <cl@linux.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Stefan Priebe <s.priebe@profihost.ag>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

mm: page allocator: initialise ZLC for first zone eligible for zone_reclaim

commit cd38b115d5ad79b0100ac6daa103c4fe2c50a913 upstream.

There have been a small number of complaints about significant stalls
while copying large amounts of data on NUMA machines reported on a
distribution bugzilla.  In these cases, zone_reclaim was enabled by
default due to large NUMA distances.  In general, the complaints have not
been about the workload itself unless it was a file server (in which case
the recommendation was disable zone_reclaim).

The stalls are mostly due to significant amounts of time spent scanning
the preferred zone for pages to free.  After a failure, it might fallback
to another node (as zonelists are often node-ordered rather than
zone-ordered) but stall quickly again when the next allocation attempt
occurs.  In bad cases, each page allocated results in a full scan of the
preferred zone.

Patch 1 checks the preferred zone for recent allocation failure
        which is particularly important if zone_reclaim has failed
        recently.  This avoids rescanning the zone in the near future and
        instead falling back to another node.  This may hurt node locality
        in some cases but a failure to zone_reclaim is more expensive than
        a remote access.

Patch 2 clears the zlc information after direct reclaim.
        Otherwise, zone_reclaim can mark zones full, direct reclaim can
        reclaim enough pages but the zone is still not considered for
        allocation.

This was tested on a 24-thread 2-node x86_64 machine.  The tests were
focused on large amounts of IO.  All tests were bound to the CPUs on
node-0 to avoid disturbances due to processes being scheduled on different
nodes.  The kernels tested are

3.0-rc6-vanilla Vanilla 3.0-rc6
zlcfirst Patch 1 applied
zlcreconsider Patches 1+2 applied

FS-Mark
./fs_mark  -d  /tmp/fsmark-10813  -D  100  -N  5000  -n  208  -L  35  -t  24  -S0  -s  524288
                fsmark-3.0-rc6       3.0-rc6        3.0-rc6
                   vanilla  zlcfirs  zlcreconsider
Files/s  min          54.90 ( 0.00%)       49.80 (-10.24%)       49.10 (-11.81%)
Files/s  mean        100.11 ( 0.00%)      135.17 (25.94%)      146.93 (31.87%)
Files/s  stddev       57.51 ( 0.00%)      138.97 (58.62%)      158.69 (63.76%)
Files/s  max         361.10 ( 0.00%)      834.40 (56.72%)      802.40 (55.00%)
Overhead min       76704.00 ( 0.00%)    76501.00 ( 0.27%)    77784.00 (-1.39%)
Overhead mean    1485356.51 ( 0.00%)  1035797.83 (43.40%)  1594680.26 (-6.86%)
Overhead stddev  1848122.53 ( 0.00%)   881489.88 (109.66%)  1772354.90 ( 4.27%)
Overhead max     7989060.00 ( 0.00%)  3369118.00 (137.13%) 10135324.00 (-21.18%)
MMTests Statistics: duration
User/Sys Time Running Test (seconds)        501.49    493.91    499.93
Total Elapsed Time (seconds)               2451.57   2257.48   2215.92

MMTests Statistics: vmstat
Page Ins                                       46268       63840       66008
Page Outs                                   90821596    90671128    88043732
Swap Ins                                           0           0           0
Swap Outs                                          0           0           0
Direct pages scanned                        13091697     8966863     8971790
Kswapd pages scanned                               0     1830011     1831116
Kswapd pages reclaimed                             0     1829068     1829930
Direct pages reclaimed                      13037777     8956828     8648314
Kswapd efficiency                               100%         99%         99%
Kswapd velocity                                0.000     810.643     826.346
Direct efficiency                                99%         99%         96%
Direct velocity                             5340.128    3972.068    4048.788
Percentage direct scans                         100%         83%         83%
Page writes by reclaim                             0           3           0
Slabs scanned                                 796672      720640      720256
Direct inode steals                          7422667     7160012     7088638
Kswapd inode steals                                0     1736840     2021238

Test completes far faster with a large increase in the number of files
created per second.  Standard deviation is high as a small number of
iterations were much higher than the mean.  The number of pages scanned by
zone_reclaim is reduced and kswapd is used for more work.

LARGE DD
                3.0-rc6       3.0-rc6       3.0-rc6
                    vanilla     zlcfirst     zlcreconsider
download tar           59 ( 0.00%)   59 ( 0.00%)   55 ( 7.27%)
dd source files       527 ( 0.00%)  296 (78.04%)  320 (64.69%)
delete source          36 ( 0.00%)   19 (89.47%)   20 (80.00%)
MMTests Statistics: duration
User/Sys Time Running Test (seconds)        125.03    118.98    122.01
Total Elapsed Time (seconds)                624.56    375.02    398.06

MMTests Statistics: vmstat
Page Ins                                     3594216      439368      407032
Page Outs                                   23380832    23380488    23377444
Swap Ins                                           0           0           0
Swap Outs                                          0         436         287
Direct pages scanned                        17482342    69315973    82864918
Kswapd pages scanned                               0      519123      575425
Kswapd pages reclaimed                             0      466501      522487
Direct pages reclaimed                       5858054     2732949     2712547
Kswapd efficiency                               100%         89%         90%
Kswapd velocity                                0.000    1384.254    1445.574
Direct efficiency                                33%          3%          3%
Direct velocity                            27991.453  184832.737  208171.929
Percentage direct scans                         100%         99%         99%
Page writes by reclaim                             0        5082       13917
Slabs scanned                                  17280       29952       35328
Direct inode steals                           115257     1431122      332201
Kswapd inode steals                                0           0      979532

This test downloads a large tarfile and copies it with dd a number of
times - similar to the most recent bug report I've dealt with.  Time to
completion is reduced.  The number of pages scanned directly is still
disturbingly high with a low efficiency but this is likely due to the
number of dirty pages encountered.  The figures could probably be improved
with more work around how kswapd is used and how dirty pages are handled
but that is separate work and this result is significant on its own.

Streaming Mapped Writer
MMTests Statistics: duration
User/Sys Time Running Test (seconds)        124.47    111.67    112.64
Total Elapsed Time (seconds)               2138.14   1816.30   1867.56

MMTests Statistics: vmstat
Page Ins                                       90760       89124       89516
Page Outs                                  121028340   120199524   120736696
Swap Ins                                           0          86          55
Swap Outs                                          0           0           0
Direct pages scanned                       114989363    96461439    96330619
Kswapd pages scanned                        56430948    56965763    57075875
Kswapd pages reclaimed                      27743219    27752044    27766606
Direct pages reclaimed                         49777       46884       36655
Kswapd efficiency                                49%         48%         48%
Kswapd velocity                            26392.541   31363.631   30561.736
Direct efficiency                                 0%          0%          0%
Direct velocity                            53780.091   53108.759   51581.004
Percentage direct scans                          67%         62%         62%
Page writes by reclaim                           385         122        1513
Slabs scanned                                  43008       39040       42112
Direct inode steals                                0          10           8
Kswapd inode steals                              733         534         477

This test just creates a large file mapping and writes to it linearly.
Time to completion is again reduced.

The gains are mostly down to two things.  In many cases, there is less
scanning as zone_reclaim simply gives up faster due to recent failures.
The second reason is that memory is used more efficiently.  Instead of
scanning the preferred zone every time, the allocator falls back to
another zone and uses it instead improving overall memory utilisation.

This patch: initialise ZLC for first zone eligible for zone_reclaim.

The zonelist cache (ZLC) is used among other things to record if
zone_reclaim() failed for a particular zone recently.  The intention is to
avoid a high cost scanning extremely long zonelists or scanning within the
zone uselessly.

Currently the zonelist cache is setup only after the first zone has been
considered and zone_reclaim() has been called.  The objective was to avoid
a costly setup but zone_reclaim is itself quite expensive.  If it is
failing regularly such as the first eligible zone having mostly mapped
pages, the cost in scanning and allocation stalls is far higher than the
ZLC initialisation step.

This patch initialises ZLC before the first eligible zone calls
zone_reclaim().  Once initialised, it is checked whether the zone failed
zone_reclaim recently.  If it has, the zone is skipped.  As the first zone
is now being checked, additional care has to be taken about zones marked
full.  A zone can be marked "full" because it should not have enough
unmapped pages for zone_reclaim but this is excessive as direct reclaim or
kswapd may succeed where zone_reclaim fails.  Only mark zones "full" after
zone_reclaim fails if it failed to reclaim enough pages after scanning.

Signed-off-by: Mel Gorman <mgorman@suse.de>
Cc: Minchan Kim <minchan.kim@gmail.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Christoph Lameter <cl@linux.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Stefan Priebe <s.priebe@profihost.ag>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

drm/radeon/kms: make sure pci max read request size is valid on evergreen+ (v2)

commit d054ac16eeb658bccadb06b12c39cee22243b10f upstream.

If the bios or OS sets the pci max read request size to 0 or an
invalid value (6,7), it can result in a hang or slowdown.  Check
and set it to something sane if it's invalid.

Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=42162

v2: use pci reg defines from include/linux/pci_regs.h

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

drm/radeon/kms: set a default max_pixel_clock

commit 9adceaa5b3d2480e2252c4a7f9c4bd7d66b8c4a2 upstream.

On some Power rv100 cards, we have no ATY OF table, but we have
no combios table either, and hence we refuse all modes on VGA-0
since we end up with a 0 max pixel clock.

Signed-off-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

md/linear: avoid corrupting structure while waiting for rcu_free to complete.

commit 1b6afa17581027218088a18a9ceda600e0ddba7a upstream.

I don't know what I was thinking putting 'rcu' after a dynamically
sized array!  The array could still be in use when we call rcu_free()
(That is the point) so we mustn't corrupt it.

Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

ARM: 7014/1: cache-l2x0: Fix L2 Cache size calculation.

commit 43c734be5571a4daad9f0a3e0b3229a1c0049917 upstream.

This patch fixes L2 Cache size calculations for L2C-210, L2C-310 and
PL310, by changing the L2X0_AUX_CTRL_WAY_SIZE_MASK from 2 bits to 3
bits.

The Auxiliary Control Register for L2C-210, L2C-310 and PL310 has 3bits
[19:17] for Way size, however the existing code only uses 2 bits to
get this value. This results in incorrect cachesize calculations.

It also results in performing operations on the whole cache when we
erroneously decide that the range is big enough (due to l2x0_size being
too small) and also prints incorrect cachesize.

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

drm/radeon/kms: evergreen & ni reset SPI block on CP resume

commit a49a50dad48586d42ebac1a6730c3a3cd5603421 upstream.

For some reason SPI block is in broken state after module
unloading. This lead to broken rendering after reloading
module. Fix this by reseting SPI block in CP resume function

Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

drm/radeon/kms: add s/r quirk for Compaq Presario V5245EU

commit 302a8e8b06d312dcb3b718dfeb42aa912b5f426b upstream.

Fixes resume on Compaq Presario V5245EU.

Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=41642

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

sparc64: Only Panther cheetah+ chips have POPC.

commit 1a8e0da5937a6c87807083baa318cf8f98dac9aa upstream.

Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

regulator: tps65910: Add missing breaks in switch/case

commit d04156bca629740a661fd0738cd69ba1f08b2b20 upstream.

Also add a default case in tps65910_list_voltage_dcdc to silence
'volt' may be used uninitialized in this function warning.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

sparc32,sun4d: Change IPI IRQ level to prevent collision between IPI and timer interrupt

commit 38f7f8f05e8239e9871f7e1c4b0a842080e85315 upstream.

On Sun4d systems running in SMP mode, IRQ 14 is used for timer interrupts
and has a specialized interrupt handler. IPI is currently set to use IRQ 14
as well, which causes it to trigger the timer interrupt handler, and not the
IPI interrupt handler.

The IPI interrupt is therefore changed to IRQ 13, which is the highest
normally handled interrupt. This IRQ is also used for SBUS interrupts,
however there is nothing in the IPI/SBUS interrupt handlers that indicate
that they will not handle sharing the interrupt.
(IRQ 13 is indicated as audio interrupt, which is unlikely to be found in a
sun4d system)

Signed-off-by: Kjetil Oftedal <oftedal@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

sparc: fix array bounds error setting up PCIC NMI trap

commit 4a0342ca8e8150bd47e7118a76e300692a1b6b7b upstream.

  CC      arch/sparc/kernel/pcic.o
arch/sparc/kernel/pcic.c: In function 'pcic_probe':
arch/sparc/kernel/pcic.c:359:33: error: array subscript is above array bounds [-Werror=array-bounds]
arch/sparc/kernel/pcic.c:359:8: error: array subscript is above array bounds [-Werror=array-bounds]
arch/sparc/kernel/pcic.c:360:33: error: array subscript is above array bounds [-Werror=array-bounds]
arch/sparc/kernel/pcic.c:360:8: error: array subscript is above array bounds [-Werror=array-bounds]
arch/sparc/kernel/pcic.c:361:33: error: array subscript is above array bounds [-Werror=array-bounds]
arch/sparc/kernel/pcic.c:361:8: error: array subscript is above array bounds [-Werror=array-bounds]
cc1: all warnings being treated as errors

I'm not particularly familiar with sparc but t_nmi (defined in head_32.S via
the TRAP_ENTRY macro) and pcic_nmi_trap_patch (defined in entry.S) both appear
to be 4 instructions long and I presume from the usage that instructions are
int sized.

Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: sparclinux@vger.kernel.org
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

sparc64: Set HAVE_C_RECORDMCOUNT

[ Upstream commit 178a29600340bef5b13cd4157053679debe35351 ]

Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

sparc: Allow handling signals when stack is corrupted.

commit 5598473a5b40c47a8c5349dd2c2630797169cf1a upstream.

If we can't push the pending register windows onto the user's stack,
we disallow signal delivery even if the signal would be delivered on a
valid seperate signal stack.

Add a register window save area in the signal frame, and store any
unsavable windows there.

On sigreturn, if any windows are still queued up in the signal frame,
try to push them back onto the stack and if that fails we kill the
process immediately.

This allows the debug/tst-longjmp_chk2 glibc test case to pass.

Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

sparc32: unbreak arch_write_unlock()

commit 3f6aa0b113846a8628baa649af422cfc6fb1d786 upstream.

The sparc32 version of arch_write_unlock() is just a plain assignment.
Unfortunately this allows the compiler to schedule side-effects in a
protected region to occur after the HW-level unlock, which is broken.
E.g., the following trivial test case gets miscompiled:

#include <linux/spinlock.h>
rwlock_t lock;
int counter;
void foo(void) { write_lock(&lock); ++counter; write_unlock(&lock); }

Fixed by adding a compiler memory barrier to arch_write_unlock().  The
sparc64 version combines the barrier and assignment into a single asm(),
and implements the operation as a static inline, so that's what I did too.

Compile-tested with sparc32_defconfig + CONFIG_SMP=y.

Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

sparc64: remove unnecessary macros from spinlock_64.h

commit a0fba3eb059e73fed2d376a901f8117734c12f1f upstream.

The sparc64 spinlock_64.h contains a number of operations defined
first as static inline functions, and then as macros with the same
names and parameters as the functions.  Maybe this was needed at
some point in the past, but now nothing seems to depend on these
macros (checked with a recursive grep looking for ifdefs on these
names).  Other archs don't define these identity-macros.

So this patch deletes these unnecessary macros.

Compile-tested with sparc64_defconfig.

Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

rt2x00: fix crash in rt2800usb_get_txwi

commit 674db1344443204b6ce3293f2df8fd1b7665deea upstream.

Patch should fix this oops:

BUG: unable to handle kernel NULL pointer dereference at 000000a0
IP: [<f81b30c9>] rt2800usb_get_txwi+0x19/0x70 [rt2800usb]
*pdpt = 0000000000000000 *pde = f000ff53f000ff53
Oops: 0000 [#1] SMP
Pid: 198, comm: kworker/u:3 Tainted: G        W   3.0.0-wl+ #9 LENOVO 6369CTO/6369CTO
EIP: 0060:[<f81b30c9>] EFLAGS: 00010283 CPU: 1
EIP is at rt2800usb_get_txwi+0x19/0x70 [rt2800usb]
EAX: 00000000 EBX: f465e140 ECX: f4494960 EDX: ef24c5f8
ESI: 810f21f5 EDI: f1da9960 EBP: f4581e80 ESP: f4581e70
 DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
Process kworker/u:3 (pid: 198, ti=f4580000 task=f4494960 task.ti=f4580000)
Call Trace:
 [<f804790f>] rt2800_txdone_entry+0x2f/0xf0 [rt2800lib]
 [<c045110d>] ? warn_slowpath_common+0x7d/0xa0
 [<f81b3a38>] ? rt2800usb_work_txdone+0x288/0x360 [rt2800usb]
 [<f81b3a38>] ? rt2800usb_work_txdone+0x288/0x360 [rt2800usb]
 [<f81b3a13>] rt2800usb_work_txdone+0x263/0x360 [rt2800usb]
 [<c046a8d6>] process_one_work+0x186/0x440
 [<c046a85a>] ? process_one_work+0x10a/0x440
 [<f81b37b0>] ? rt2800usb_probe_hw+0x120/0x120 [rt2800usb]
 [<c046c283>] worker_thread+0x133/0x310
 [<c04885db>] ? trace_hardirqs_on+0xb/0x10
 [<c046c150>] ? manage_workers+0x1e0/0x1e0
 [<c047054c>] kthread+0x7c/0x90
 [<c04704d0>] ? __init_kthread_worker+0x60/0x60
 [<c0826b42>] kernel_thread_helper+0x6/0x1

Oops might happen because we check rt2x00queue_empty(queue) twice,
but this condition can change and we can process entry in
rt2800_txdone_entry(), which was already processed by
rt2800usb_txdone_entry_check() -> rt2x00lib_txdone_noinfo() and
has nullify entry->skb .

Reported-by: Justin Piszcz <jpiszcz@lucidpixels.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

rt2x00: fix crash in rt2800usb_write_tx_desc

commit 4b1bfb7d2d125af6653d6c2305356b2677f79dc6 upstream.

Patch should fix this oops:

BUG: unable to handle kernel NULL pointer dereference at 000000a0
IP: [<f8e06078>] rt2800usb_write_tx_desc+0x18/0xc0 [rt2800usb]
*pdpt = 000000002408c001 *pde = 0000000024079067 *pte = 0000000000000000
Oops: 0000 [#1] SMP
EIP: 0060:[<f8e06078>] EFLAGS: 00010282 CPU: 0
EIP is at rt2800usb_write_tx_desc+0x18/0xc0 [rt2800usb]
EAX: 00000035 EBX: ef2bef10 ECX: 00000000 EDX: d40958a0
ESI: ef1865f8 EDI: ef1865f8 EBP: d4095878 ESP: d409585c
 DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
Call Trace:
 [<f8da5e85>] rt2x00queue_write_tx_frame+0x155/0x300 [rt2x00lib]
 [<f8da424c>] rt2x00mac_tx+0x7c/0x370 [rt2x00lib]
 [<c04882b2>] ? mark_held_locks+0x62/0x90
 [<c081f645>] ? _raw_spin_unlock_irqrestore+0x35/0x60
 [<c04884ba>] ? trace_hardirqs_on_caller+0x5a/0x170
 [<c04885db>] ? trace_hardirqs_on+0xb/0x10
 [<f8d618ac>] __ieee80211_tx+0x5c/0x1e0 [mac80211]
 [<f8d631fc>] ieee80211_tx+0xbc/0xe0 [mac80211]
 [<f8d63163>] ? ieee80211_tx+0x23/0xe0 [mac80211]
 [<f8d632e1>] ieee80211_xmit+0xc1/0x200 [mac80211]
 [<f8d63220>] ? ieee80211_tx+0xe0/0xe0 [mac80211]
 [<c0487d45>] ? lock_release_holdtime+0x35/0x1b0
 [<f8d63986>] ? ieee80211_subif_start_xmit+0x446/0x5f0 [mac80211]
 [<f8d637dd>] ieee80211_subif_start_xmit+0x29d/0x5f0 [mac80211]
 [<f8d63924>] ? ieee80211_subif_start_xmit+0x3e4/0x5f0 [mac80211]
 [<c0760188>] ? sock_setsockopt+0x6a8/0x6f0
 [<c0760000>] ? sock_setsockopt+0x520/0x6f0
 [<c076daef>] dev_hard_start_xmit+0x2ef/0x650

Oops might happen because we perform parallel putting new entries in a
queue (rt2x00queue_write_tx_frame()) and removing entries after
finishing transmitting (rt2800usb_work_txdone()). There are cases when
_txdone may process an entry that was not fully send and nullify
entry->skb .

To fix check in _txdone if entry has flags that indicate pending
transmission and wait until flags get cleared.

Reported-by: Justin Piszcz <jpiszcz@lucidpixels.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

atm: br2684: Fix oops due to skb->dev being NULL

commit fbe5e29ec1886967255e76946aaf537b8cc9b81e upstream.

This oops have been already fixed with commit

    27141666b69f535a4d63d7bc6d9e84ee5032f82a

    atm: [br2684] Fix oops due to skb->dev being NULL

    It happens that if a packet arrives in a VC between the call to open it on
    the hardware and the call to change the backend to br2684, br2684_regvcc
    processes the packet and oopses dereferencing skb->dev because it is
    NULL before the call to br2684_push().

but have been introduced again with commit

    b6211ae7f2e56837c6a4849316396d1535606e90

    atm: Use SKB queue and list helpers instead of doing it by-hand.

Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

pata_via: disable ATAPI DMA on AVERATEC 3200

commit 6d0e194d2eefcaab6dbdca1f639748660144acb5 upstream.

On AVERATEC 3200, pata_via causes memory corruption with ATAPI DMA,
which often leads to random kernel oops.  The cause of the problem is
not well understood yet and only small subset of machines using the
controller seem affected.  Blacklist ATAPI DMA on the machine.

Signed-off-by: Tejun Heo <tj@kernel.org>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=11426
Reported-and-tested-by: Jim Bray <jimsantelmo@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

savagedb: Fix typo causing regression in savage4 series video chip detection

commit 4b00e4b3940eabb38adeec0823751820fe2d6fda upstream.

Two additional savage4 variants were added, but the S3_SAVAGE4_SERIES
macro was incompletely modified, resulting in a false positive detection
of a savage4 card regardless of which savage card is actually present.

For non-savage4 series cards, such as a Savage/IX-MV card, this results
in garbled video and/or a hard-hang at boot time.  Fix this by changing
an '||' to an '&&' in the S3_SAVAGE4_SERIES macro.

Signed-off-by: John P. Stanley <jpsinthemix@verizon.net>
Reviewed-by: Tormod Volden <debian.tormod@gmail.com>
[ The macros have incomplete parenthesis too, but whatever ..  -Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

rt2x00: do not drop usb dev reference counter on suspend

commit 543cc38c8fe86deba4169977c61eb88491036837 upstream.

When hibernating ->resume may not be called by usb core, but disconnect
and probe instead, so we do not increase the counter after decreasing
it in ->supend. As a result we free memory early, and get crash when
unplugging usb dongle.

BUG: unable to handle kernel paging request at 6b6b6b9f
IP: [<c06909b0>] driver_sysfs_remove+0x10/0x30
*pdpt = 0000000034f21001 *pde = 0000000000000000
Pid: 20, comm: khubd Not tainted 3.1.0-rc1-wl+ #20 LENOVO 6369CTO/6369CTO
EIP: 0060:[<c06909b0>] EFLAGS: 00010202 CPU: 1
EIP is at driver_sysfs_remove+0x10/0x30
EAX: 6b6b6b6b EBX: f52bba34 ECX: 00000000 EDX: 6b6b6b6b
ESI: 6b6b6b6b EDI: c0a0ea20 EBP: f61c9e68 ESP: f61c9e64
 DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
Process khubd (pid: 20, ti=f61c8000 task=f6138270 task.ti=f61c8000)
Call Trace:
 [<c06909ef>] __device_release_driver+0x1f/0xa0
 [<c0690b20>] device_release_driver+0x20/0x40
 [<c068fd64>] bus_remove_device+0x84/0xe0
 [<c068e12a>] ? device_remove_attrs+0x2a/0x80
 [<c068e267>] device_del+0xe7/0x170
 [<c06d93d4>] usb_disconnect+0xd4/0x180
 [<c06d9d61>] hub_thread+0x691/0x1600
 [<c0473260>] ? wake_up_bit+0x30/0x30
 [<c0442a39>] ? complete+0x49/0x60
 [<c06d96d0>] ? hub_disconnect+0xd0/0xd0
 [<c06d96d0>] ? hub_disconnect+0xd0/0xd0
 [<c0472eb4>] kthread+0x74/0x80
 [<c0472e40>] ? kthread_worker_fn+0x150/0x150
 [<c0809b3e>] kernel_thread_helper+0x6/0x10

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

ath9k_hw: Fix STA (AR9485) bringup issue due to incorrect MAC address

commit b503c7a273c0a3018ad11ea8c513c639120afbf4 upstream.

Due to some recent optimization done in the way the mac address
bytes are written into the OTP memory, some AR9485 chipsets were
forced to use the first byte from the eeprom template and the
remaining bytes are read from OTP.

AR9485 happens to use generic eeprom template which has 0x1 as
the first byte causes issues in bringing up the card.

So fixed the eeprom template accordingly to address the issue.

Cc: Paul Stewart <pstew@google.com>
Signed-off-by: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>