OSDN Git Service
Jani Nikula [Mon, 4 Nov 2019 14:14:36 +0000 (16:14 +0200)]
drm/i915/dsc: make parameter arrays const
No need for them to be mutable.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191104141439.26312-1-jani.nikula@intel.com
Jani Nikula [Fri, 1 Nov 2019 14:20:24 +0000 (16:20 +0200)]
drm/i915: update rawclk also on resume
Since CNP it's possible for rawclk to have two different values, 19.2
and 24 MHz. If the value indicated by SFUSE_STRAP register is different
from the power on default for PCH_RAWCLK_FREQ, we'll end up having a
mismatch between the rawclk hardware and software states after
suspend/resume. On previous platforms this used to work by accident,
because the power on defaults worked just fine.
Update the rawclk also on resume. The natural place to do this would be
intel_modeset_init_hw(), however VLV/CHV need it done before
intel_power_domains_init_hw(). Thus put it there even if it feels
slightly out of place.
v2: Call intel_update_rawclck() in intel_power_domains_init_hw() for all
platforms (Ville).
Reported-by: Shawn Lee <shawn.c.lee@intel.com>
Cc: Shawn Lee <shawn.c.lee@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Shawn Lee <shawn.c.lee@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191101142024.13877-1-jani.nikula@intel.com
Lucas De Marchi [Wed, 30 Oct 2019 01:24:47 +0000 (18:24 -0700)]
drm/i915: avoid reading DP_TP_CTL twice
Just avoid the additional read in case DP_TP_CTL is enabled:
read it once and save the value.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191030012448.14937-5-lucas.demarchi@intel.com
Lucas De Marchi [Wed, 30 Oct 2019 01:24:46 +0000 (18:24 -0700)]
drm/i915/tgl: do not enable transcoder clock twice on MST
For MST on Tiger Lake there are different moments when we need to
configure the transcoder clock select. For the first link this is in step
7.a of the spec, before training the link. For additional streams this
should be done as part of step 8.b after programming receiver VC Payload
ID.
Bspec: 49190
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191030012448.14937-4-lucas.demarchi@intel.com
Lucas De Marchi [Wed, 30 Oct 2019 01:24:45 +0000 (18:24 -0700)]
drm/i915: add wrappers to get intel connector state
Wrap drm_atomic_get_old_connector_state so we can get the
intel_digital_connector_state and make it easier to migrate to intel
types.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191030012448.14937-3-lucas.demarchi@intel.com
José Roberto de Souza [Wed, 30 Oct 2019 01:24:44 +0000 (18:24 -0700)]
drm/i915: Add for_each_new_intel_connector_in_state()
The same macro as for_each_new_connector_in_state() but it uses
intel/i915 types instead of the drm ones.
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190823082055.5992-11-lucas.demarchi@intel.com
Link: https://patchwork.freedesktop.org/patch/msgid/20191030012448.14937-2-lucas.demarchi@intel.com
Ville Syrjälä [Thu, 31 Oct 2019 16:56:52 +0000 (18:56 +0200)]
drm/i915: Eliminate redundancy in intel_primary_plane_create()
Lots of redundant assignments inside intel_primary_plane_create().
Get rid of them.
v2: Rebase due to fp16 landing
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031165652.10868-8-ville.syrjala@linux.intel.com
Ville Syrjälä [Thu, 31 Oct 2019 16:56:51 +0000 (18:56 +0200)]
drm/i915: Sort format arrays consistently
Let's try to keep the pixel format arrays somewhat sorted:
1. RGB before YUV
2. smaller bpp before larger bpp
3. X before A
4. RGB before BGR
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031165652.10868-7-ville.syrjala@linux.intel.com
Ville Syrjälä [Thu, 31 Oct 2019 16:56:50 +0000 (18:56 +0200)]
drm/i915: Add 10bpc formats with alpha for icl+
ICL+ again supports alpha blending with 10bpc pixel formats.
Expose them.
v2: Add all the stuff I missed earlier!
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031165652.10868-6-ville.syrjala@linux.intel.com
Ville Syrjälä [Thu, 31 Oct 2019 16:56:49 +0000 (18:56 +0200)]
drm/i915: Expose C8 on VLV/CHV sprite planes
VLV/CHV sprite planes also support the C8 format. Let's expose that.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031165652.10868-5-ville.syrjala@linux.intel.com
Ville Syrjälä [Thu, 31 Oct 2019 16:56:48 +0000 (18:56 +0200)]
drm/i915: Add missing 10bpc formats for pipe B sprites on CHV
CHV pipe B sprites gained support for the 10bpc X/ARGB pixel formats.
On VLV and CHV pipe A/C these are only supported by the primary
plane. Add the require bits to expose the new formats.
v2: Reorder the formats for consistency
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031165652.10868-4-ville.syrjala@linux.intel.com
Ville Syrjälä [Thu, 31 Oct 2019 16:56:47 +0000 (18:56 +0200)]
drm/i915: Expose alpha formats on VLV/CHV primary planes
Currently we expose VLV/CHV alpha blending only on the sprite
planes, but the primary planes can do it as well. Let's flip
it on.
v2: Rebase due to fp16 landing
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031165652.10868-3-ville.syrjala@linux.intel.com
Ville Syrjälä [Thu, 31 Oct 2019 16:56:46 +0000 (18:56 +0200)]
drm/i915: Expose 10:10:10 XRGB formats on SNB-BDW sprites
SNB-BDW support 10:10:10 formats on the sprite planes. Let's expose
them.
v2: Rebase due to fp16 landing
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031165652.10868-2-ville.syrjala@linux.intel.com
Chris Wilson [Mon, 4 Nov 2019 13:53:07 +0000 (13:53 +0000)]
drm/i915/execlists: Reset CSB pointers by mmio as well
Sometimes Icelake forgets to reset the CSB pointers on a GPU reset,
leading to it carry on updating the old tail of the buffer.
<0>[ 618.138490] i915_sel-5636 3d..1 673425465us : trace_ports: vecs0: submit { 14de2:504, 0:0 }
<0>[ 618.138490] i915_sel-5636 3.... 673425493us : intel_engine_reset: vecs0 flags=100
<0>[ 618.138490] i915_sel-5636 3.... 673425493us : execlists_reset_prepare: vecs0: depth<-0
<0>[ 618.138490] i915_sel-5636 3.... 673425493us : intel_engine_stop_cs: vecs0
<0>[ 618.138490] i915_sel-5636 3.... 673425523us : __intel_gt_reset: engine_mask=40
<0>[ 618.138490] i915_sel-5636 3.... 673425568us : execlists_reset: vecs0
<0>[ 618.138490] i915_sel-5636 3d..1 673425568us : process_csb: vecs0 cs-irq head=1, tail=2
<0>[ 618.138490] i915_sel-5636 3d..1 673425568us : process_csb: vecs0 csb[2]: status=0x00000001:0x40000000
<0>[ 618.138490] i915_sel-5636 3d..1 673425569us : trace_ports: vecs0: promote { 14de2:504*, 0:0 }
<0>[ 618.138490] i915_sel-5636 3d..1 673425570us : __i915_request_reset: vecs0 rq=14de2:504, guilty? yes
<0>[ 618.138490] i915_sel-5636 3d..1 673425571us : __execlists_reset: vecs0 replay {head:2de0, tail:2e48}
<0>[ 618.138490] i915_sel-5636 3d..1 673425572us : __i915_request_unsubmit: vecs0 fence 14de2:504, current 503
<0>[ 618.138490] i915_sel-5636 3.... 673435544us : intel_engine_cancel_stop_cs: vecs0
<0>[ 618.138490] i915_sel-5636 3.... 673435544us : process_csb: vecs0 cs-irq head=11, tail=11
<0>[ 618.138490] i915_sel-5636 3d..1 673435545us : __i915_request_submit: vecs0 fence 14de2:504, current 503
<0>[ 618.138490] i915_sel-5636 3d..1 673435546us : __execlists_submission_tasklet: vecs0: queue_priority_hint:-
2147483648, submit:yes
<0>[ 618.138490] i915_sel-5636 3d..1 673435548us : trace_ports: vecs0: submit { 14de2:504*, 0:0 }
<0>[ 618.138490] i915_sel-5636 3.... 673435549us : execlists_reset_finish: vecs0: depth->0
<0>[ 618.138490] ksoftirq-21 2..s. 673435592us : process_csb: vecs0 cs-irq head=11, tail=3
<0>[ 618.138490] ksoftirq-21 2..s. 673435593us : process_csb: vecs0 csb[0]: status=0x00000001:0x40000000
<0>[ 618.138490] ksoftirq-21 2..s. 673435594us : trace_ports: vecs0: promote { 14de2:504*, 0:0 }
<0>[ 618.138490] ksoftirq-21 2..s. 673435596us : process_csb: vecs0 csb[1]: status=0x00000018:0x40000040
<0>[ 618.138490] ksoftirq-21 2..s. 673435597us : trace_ports: vecs0: completed { 14de2:504*, 0:0 }
<0>[ 618.138490] ksoftirq-21 2..s. 673435612us : process_csb: process_csb:2188 GEM_BUG_ON(!i915_request_completed(*execlists->active) && !reset_in_progress(execlists))
After the reset, we do another clflush before checking the CSB to be
sure we see whatever was left in the CSB prior to the reset. So it is
unlikely to be an incoherent view of the CSB, and more likely that
Icelake didn't reset its pointers.
References:
582a6f90aa0d ("drm/i915/execlists: Add a paranoid flush of the CSB pointers upon reset")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191104135307.21083-1-chris@chris-wilson.co.uk
Jani Nikula [Fri, 1 Nov 2019 13:43:33 +0000 (15:43 +0200)]
drm/i915: add for_each_port() and use it
Add another for_each style macro to the pile of custom looping macros.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191101134333.11612-1-jani.nikula@intel.com
Chris Wilson [Sun, 3 Nov 2019 16:23:05 +0000 (16:23 +0000)]
drm/i915: Protect request peeking with RCU
Since the execlists_active() is no longer protected by the
engine->active.lock, we need to protect the request pointer with RCU to
prevent it being freed as we evaluate whether or not we need to preempt.
Fixes:
df403069029d ("drm/i915/execlists: Lift process_csb() out of the irq-off spinlock")
Fixes:
13ed13a4dcbf ("drm/i915: Don't set queue_priority_hint if we don't kick the submission")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191104090158.2959-2-chris@chris-wilson.co.uk
Chris Wilson [Sun, 3 Nov 2019 09:50:38 +0000 (09:50 +0000)]
drm/i915/gt: Drop false assertion on user_forcewake
The counter is removed from the pm wakeref count, but it remains intact
so that we can restore it upon resume. Ergo inside suspend, it may have
a value.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Andi Shyti <andi.shyti@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191104090158.2959-1-chris@chris-wilson.co.uk
Chris Wilson [Fri, 1 Nov 2019 08:29:19 +0000 (08:29 +0000)]
drm/i915/execlists: Ignore the inactive kernel context in assert_pending_valid
Filter out warnings for the kernel context that is used to flush
inactive contexts, as they do no not pose a risk.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191101082919.21122-1-chris@chris-wilson.co.uk
Chris Wilson [Sat, 2 Nov 2019 12:57:39 +0000 (12:57 +0000)]
drm/i915/execlists: Verify context register state before execution
Check that the context's ring register state still matches our
expectations prior to execution.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191102125739.24626-1-chris@chris-wilson.co.uk
Chris Wilson [Fri, 1 Nov 2019 18:10:22 +0000 (18:10 +0000)]
drm/i915/selftests: Flush all active callbacks
Flushing the outer i915_active is not enough, as we need the barrier to
be applied across all the active dma_fence callbacks. So we must
serialise with each outstanding fence.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=112096
References:
f79520bb3337 ("drm/i915/selftests: Synchronize checking active status with retirement")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Andi Shyti <andi.shyti@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191101181022.25633-1-chris@chris-wilson.co.uk
Chris Wilson [Fri, 1 Nov 2019 19:21:16 +0000 (19:21 +0000)]
drm/i915/perf: Reverse a ternary to make sparse happy
Avoid
drivers/gpu/drm/i915/i915_perf.c:2442:85: warning: dubious: x | !y
simply by inverting the predicate and reversing the ternary.
v2: Move the long lines into their own function so there is no confusion
on operator precedence.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191101192116.12647-1-chris@chris-wilson.co.uk
Chris Wilson [Fri, 1 Nov 2019 17:44:05 +0000 (17:44 +0000)]
drm/i915/selftests: Add intel_gt_suspend_prepare
Call suspend_prepare first so that we don't leave GuC so confused.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Andi Shyti <andi.shyti@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191101174405.7389-1-chris@chris-wilson.co.uk
Chris Wilson [Fri, 1 Nov 2019 14:10:09 +0000 (14:10 +0000)]
drm/i915: Defer rc6 shutdown to suspend_late
Currently we shutdown rc6 during i915_gem_resume() but this is called
during the preparation phase (i915_drm_prepare) for all suspend paths,
but we only want to shutdown rc6 for S3+. Move the actual shutdown to
i915_gem_suspend_late().
We then need to differentiate between suspend targets, to distinguish S0
(s2idle) where the device is kept awake but needs to be in a low power
mode (the same as runtime suspend) from the device suspend levels where
we lose control of HW and so must disable any HW access to dangling
memory.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111909
Fixes:
c113236718e8 ("drm/i915: Extract GT render sleep (rc6) management")
Testcase: igt/gem_exec_suspend/power-S0
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Andi Shyti <andi.shyti@intel.com>
Acked-by: Andi Shyti <andi.shyti@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191101141009.15581-4-chris@chris-wilson.co.uk
Chris Wilson [Fri, 1 Nov 2019 14:10:08 +0000 (14:10 +0000)]
drm/i915/gt: Move user_forcewake application to GT
We already track the debugfs user_forcewake on the GT, so it is natural
to pull the suspend/resume handling under gt/ as well.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Andi Shyti <andi.shyti@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191101141009.15581-3-chris@chris-wilson.co.uk
Chris Wilson [Fri, 1 Nov 2019 14:10:07 +0000 (14:10 +0000)]
drm/i915/gem: Leave reloading kernel context on resume to GT
As we already do reload the kernel context in intel_gt_resume, repeating
that action inside i915_gem_resume() as well is redundant.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Andi Shyti <andi.shyti@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191101141009.15581-2-chris@chris-wilson.co.uk
Chris Wilson [Fri, 1 Nov 2019 14:10:06 +0000 (14:10 +0000)]
drm/i915/gt: Call intel_gt_sanitize() directly
Assume all responsibility for operating on the HW to sanitize the GT
state upon load/resume in intel_gt_sanitize() itself.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Andi Shyti <andi.shyti@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191101141009.15581-1-chris@chris-wilson.co.uk
Chris Wilson [Fri, 1 Nov 2019 13:04:06 +0000 (13:04 +0000)]
drm/i915/gt: Pull timeline initialise to intel_gt_init_early
Our timelines are currently contained within an intel_gt, and we only
need to perform list/spinlock initialisation, so we can pull the
intel_timelines_init() into our intel_gt_init_early().
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191101130406.4142-1-chris@chris-wilson.co.uk
Maarten Lankhorst [Thu, 31 Oct 2019 11:26:10 +0000 (12:26 +0100)]
drm/i915: Remove special case slave handling during hw programming, v3.
Now that we split plane_state which I didn't want to do yet, we can
program the slave plane without requiring the master plane.
This is useful for programming bigjoiner slave planes as well. We
will no longer need the master's plane_state.
Changes since v1:
- set src/dst rectangles after copy_uapi_to_hw_state.
Changes since v2:
- Use the correct color_plane for pre-gen11 by using planar_linked_plane != NULL.
- Use drm_format_info_is_yuv_semiplanar in skl_plane_check() to fix gen11+.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031112610.27608-12-maarten.lankhorst@linux.intel.com
Maarten Lankhorst [Thu, 31 Oct 2019 11:26:09 +0000 (12:26 +0100)]
drm/i915: Complete plane hw and uapi split, v2.
Splitting plane state is easier than splitting crtc_state,
before plane check we copy the drm properties to hw so we can
do the same in bigjoiner later on.
We copy the state after we did all the modeset handling, but fortunately
i915 seems to be split correctly and nothing during modeset looks
at plane_state.
Changes since v1:
- Do not clear hw state on duplication.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031112610.27608-11-maarten.lankhorst@linux.intel.com
Maarten Lankhorst [Thu, 31 Oct 2019 11:26:08 +0000 (12:26 +0100)]
drm/i915: Perform automated conversions for plane uapi/hw split, base -> uapi.
Split up plane_state->base to uapi. This is done using the following patch,
ran after the previous commit that splits out any hw references:
@@
struct intel_plane_state *T;
identifier x;
@@
-T->base.x
+T->uapi.x
@@
struct intel_plane_state *T;
@@
-T->base
+T->uapi
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031112610.27608-10-maarten.lankhorst@linux.intel.com
Maarten Lankhorst [Thu, 31 Oct 2019 11:26:07 +0000 (12:26 +0100)]
drm/i915: Perform automated conversions for plane uapi/hw split, base -> hw.
Split up plane_state->base to hw. This is done using the following patch:
@@
struct intel_plane_state *T;
identifier x =~ "^(crtc|fb|alpha|pixel_blend_mode|rotation|color_encoding|color_range)$";
@@
-T->base.x
+T->hw.x
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031112610.27608-9-maarten.lankhorst@linux.intel.com
Maarten Lankhorst [Thu, 31 Oct 2019 11:26:06 +0000 (12:26 +0100)]
drm/i915: Perform manual conversions for plane uapi/hw split, v2.
get_crtc_from_states() is called before plane_state is copied to uapi,
so use the uapi state there.
intel_legacy_cursor_update() could probably get away with looking at
the hw state, but for clarity always look at the uapi state.
Changes since v1:
- Convert entirety of intel_legacy_cursor_update (Ville).
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031112610.27608-8-maarten.lankhorst@linux.intel.com
Maarten Lankhorst [Thu, 31 Oct 2019 11:26:05 +0000 (12:26 +0100)]
drm/i915: Add aliases for uapi and hw to plane_state
Prepare to split up hw and uapi machinally, by adding a uapi and
hw alias. We will remove the base in a bit. This is a split from the
original uapi/hw patch, which did it all in one go.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031112610.27608-7-maarten.lankhorst@linux.intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Maarten Lankhorst [Thu, 31 Oct 2019 11:26:04 +0000 (12:26 +0100)]
drm/i915: Complete crtc hw/uapi split, v6.
Now that we separated everything into uapi and hw, it's
time to make the split definitive. Remove the union and
make a copy of the hw state on modeset and fastset.
Color blobs are copied in crtc atomic_check(), right
before color management is checked.
Changes since v1:
- Copy all blobs immediately after drm_atomic_helper_check_modeset().
- Clear crtc_state->hw on disable, instead of using clear_intel_crtc_state().
Changes since v2:
- Use intel_crtc_free_hw_state + clear in intel_crtc_disable_noatomic().
- Make a intel_crtc_prepare_state() function that clears the crtc_state
and copies hw members.
- Remove setting uapi.adjusted_mode, we now have a direct call to
drm_calc_timestamping_constants().
Changes since v3:
- Rename prefix copy_hw_to_uapi_state() with intel_crtc.
- Copy color blobs to uapi as well.
- Add a intel_crtc_copy_uapi_to_hw_state_nomodeset() function for clarity.
Changes since v4:
- Copy hw.adjusted_mode back to uapi.adjusted_mode, to shut up
the call to drm_calc_timestamping_constants() in
drm_atomic_helper_update_legacy_modeset_state().
- Use drm_property_replace_blob (Ville).
Changes since v5:
- Use hw->mode in intel_modeset_readout_hw_state(). (Ville)
- Copy to uapi.mode using drm_atomic_set_mode_for_crtc(). (Ville)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031112610.27608-6-maarten.lankhorst@linux.intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Maarten Lankhorst [Thu, 31 Oct 2019 11:26:03 +0000 (12:26 +0100)]
drm/i915: Perform automated conversions for crtc uapi/hw split, base -> uapi.
Split up crtc_state->base to uapi. This is done using the following patch,
ran after the previous commit that splits out any hw references:
@@
struct intel_crtc_state *T;
@@
-T->base
+T->uapi
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031112610.27608-5-maarten.lankhorst@linux.intel.com
Maarten Lankhorst [Thu, 31 Oct 2019 11:26:02 +0000 (12:26 +0100)]
drm/i915: Perform automated conversions for crtc uapi/hw split, base -> hw.
Split up crtc_state->base to hw where appropriate. This is done using the following patch:
@@
struct intel_crtc_state *T;
identifier x =~ "^(active|enable|degamma_lut|gamma_lut|ctm|mode|adjusted_mode)$";
@@
-T->base.x
+T->hw.x
@@
struct drm_crtc_state *T;
identifier x =~ "^(active|enable|degamma_lut|gamma_lut|ctm|mode|adjusted_mode)$";
@@
-to_intel_crtc_state(T)->base.x
+to_intel_crtc_state(T)->hw.x
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031112610.27608-4-maarten.lankhorst@linux.intel.com
Maarten Lankhorst [Thu, 31 Oct 2019 11:26:01 +0000 (12:26 +0100)]
drm/i915: Perform manual conversions for crtc uapi/hw split, v2.
intel_get_load_detect_pipe() needs to set uapi active,
uapi enable is set by the call to drm_atomic_set_mode_for_crtc(),
so we can remove it.
intel_pipe_config_compare() needs to look at hw state, but I didn't
change spatch to look at it. It's easy enough to do manually.
intel_atomic_check() definitely needs to check for uapi enable,
otherwise intel_modeset_pipe_config cannot copy uapi state to hw.
Changes since v1:
- Actually set uapi.active in get_load_detect_pipe().
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031112610.27608-3-maarten.lankhorst@linux.intel.com
Maarten Lankhorst [Thu, 31 Oct 2019 11:26:00 +0000 (12:26 +0100)]
drm/i915: Add aliases for uapi and hw to crtc_state
Prepare to split up hw and uapi machinally, by adding a uapi and
hw alias. We will remove the base in a bit. This is a split from the
original uapi/hw patch, which did it all in one go.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031112610.27608-2-maarten.lankhorst@linux.intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Maarten Lankhorst [Thu, 31 Oct 2019 11:25:59 +0000 (12:25 +0100)]
drm/i915: Handle a few more cases for crtc hw/uapi split, v3.
We are still looking at drm_crtc_state in a few places, convert those
to use intel_crtc_state instead.
Changes since v1:
- Move to before uapi/hw split.
- Add hunks for intel_pm.c as well.
Changes since v2:
- Incorporate Ville's feedback.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031112610.27608-1-maarten.lankhorst@linux.intel.com
Chris Wilson [Fri, 1 Nov 2019 10:15:28 +0000 (10:15 +0000)]
drm/i915/selftests: Spin on all engines simultaneously
Vanshidhar Konda asked for the simplest test "to verify that the kernel
can submit and hardware can execute batch buffers on all the command
streamers in parallel." We have a number of tests in userspace that
submit load to each engine and verify that it is present, but strictly
we have no selftest to prove that the kernel can _simultaneously_
execute on all known engines. (We have tests to demonstrate that we can
submit to HW in parallel, but we don't insist that they execute in
parallel.)
v2: Improve the igt_spinner support for older gen.
Suggested-by: Vanshidhar Konda <vanshidhar.r.konda@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Vanshidhar Konda <vanshidhar.r.konda@intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Vanshidhar Konda <vanshidhar.r.konda@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191101101528.10553-1-chris@chris-wilson.co.uk
Joonas Lahtinen [Fri, 1 Nov 2019 10:41:13 +0000 (12:41 +0200)]
drm/i915: Update DRIVER_DATE to
20191101
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Chris Wilson [Fri, 1 Nov 2019 08:49:40 +0000 (08:49 +0000)]
drm/i915/selftests: Start kthreads before stopping
An interesting observation made with our parallel selftests was that on
our small/single cpu systems we would call kthread_stop() before the
kthreads were spawned. If this happens, the kthread is never run at all;
completely bypassing the test.
A simple yield() from the parent will ensure that all children have the
opportunity to start before we reap them.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191101084940.31838-1-chris@chris-wilson.co.uk
Chris Wilson [Fri, 1 Nov 2019 09:51:47 +0000 (09:51 +0000)]
drm/i915/lmem: Check against i915_selftest only under CONFIG_SELFTEST
The i915_selftest module parameters only exist when
CONFIG_DRM_I915_SELFTEST is set.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191101095147.9769-1-chris@chris-wilson.co.uk
Chris Wilson [Thu, 31 Oct 2019 09:01:04 +0000 (09:01 +0000)]
drm/i915/gem: Refine occupancy test in kill_context()
Don't just look at the very last request in a queue when deciding if we
need to evict the context from the GPU, as that request may still be in
the submission queue while the rest of the context is running!
Instead, walk back along the queued requests looking for the active
request and checking that.
Fixes:
2e0986a58cc4 ("drm/i915/gem: Cancel contexts when hangchecking is disabled")
Testcase: igt/gem_ctx_persistence/queued
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031090104.22245-1-chris@chris-wilson.co.uk
Joonas Lahtinen [Fri, 1 Nov 2019 07:04:29 +0000 (09:04 +0200)]
drm/i915: Update DRIVER_DATE to
20191101
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Matthew Auld [Wed, 30 Oct 2019 17:33:20 +0000 (17:33 +0000)]
drm/i915/lmem: add the fake lmem region
Intended for upstream testing so that we can still exercise the LMEM
plumbing and !i915_ggtt_has_aperture paths. Smoke tested on Skull Canyon
device. This works by allocating an intel_memory_region for a reserved
portion of system memory, which we treat like LMEM. For the LMEMBAR we
steal the aperture and 1:1 it map to the stolen region.
To enable simply set the i915 modparam fake_lmem_start= on the kernel
cmdline with the start of reserved region(see memmap=). The size of the
region we can use is determined by the size of the mappable aperture, so
the size of reserved region should be >= mappable_end. For now we only
enable for the selftests. Depends on CONFIG_DRM_I915_UNSTABLE being
enabled.
eg. memmap=2G$16G i915.fake_lmem_start=0x400000000
v2: make fake_lmem_start an i915 modparam
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Abdiel Janulgue <abdiel.janulgue@linux.intel.com>
Cc: Arkadiusz Hiler <arkadiusz.hiler@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20191030173320.8850-1-matthew.auld@intel.com
José Roberto de Souza [Tue, 29 Oct 2019 01:10:14 +0000 (18:10 -0700)]
drm/i915/dp: Do not switch aux to TBT mode for non-TC ports
Non-TC ports always have tc_mode == TC_PORT_TBT_ALT so it was
switching aux to TBT mode for all combo-phy ports, happily this did
not caused any issue but is better follow BSpec.
Also this is reserved bit before ICL.
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Fixes:
e9b7e1422d40 ("drm/i915: Sanitize the terminology used for TypeC port modes")
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191029011014.286885-1-jose.souza@intel.com
Daniele Ceraolo Spurio [Thu, 31 Oct 2019 01:30:40 +0000 (18:30 -0700)]
drm/i915/guc: drop guc shared area
Recent GuC doesn't require the shared area. We still have one user in
i915 (engine reset via guc) because we haven't updated the command to
match the current guc submission flow [1]. Since the flow in guc is
about to change again, just disable the command for now and add a note
that we'll implement it as part of the new flow.
[1] https://patchwork.freedesktop.org/patch/295038/
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: John Harrison <John.C.Harrison@Intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: Fernando Pacheco <fernando.pacheco@intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031013040.25803-2-daniele.ceraolospurio@intel.com
Daniele Ceraolo Spurio [Thu, 31 Oct 2019 01:30:39 +0000 (18:30 -0700)]
drm/i915: drop lrc header page
Recent GuC binaries (including all the ones we're currently using)
don't require this shared area anymore, having moved the relevant
entries into the stage pool instead. i915 itself doesn't write
anything into it either, so we can safely drop it.
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: John Harrison <John.C.Harrison@Intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031013040.25803-1-daniele.ceraolospurio@intel.com
Chris Wilson [Wed, 30 Oct 2019 19:21:49 +0000 (19:21 +0000)]
drm/i915: Split detaching and removing the vma
In order to keep the assert_bind_count() valid, we need to hold the vma
page reference until after we drop the bind count. However, we must also
keep the drm_mm_remove_node() as the last action of i915_vma_unbind() so
that it serialises with the unlocked check inside i915_vma_destroy(). So
we need to split up i915_vma_remove() so that we order the detach, drop
pages and remove as required during unbind.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=112067
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191030192159.18404-1-chris@chris-wilson.co.uk
Chris Wilson [Thu, 31 Oct 2019 10:11:16 +0000 (10:11 +0000)]
drm/i915/selftests: Pretty print the i915_active
If the idle_pulse fails to flush the i915_active, dump the tree to see
if that has any clues.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031101116.19894-1-chris@chris-wilson.co.uk
Chris Wilson [Thu, 31 Oct 2019 09:42:59 +0000 (09:42 +0000)]
drm/i915/selftests: Assert that the idle_pulse is sent
When checking the heartbeat pulse, we expect it to have been sent by the
time we have slept. We can verify this by checking the engine serial
number to see if that matches the predicted pulse serial. It will always
be true if, and only if, the pulse was sent by itself (as designed by
the test).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031094259.23028-1-chris@chris-wilson.co.uk
Ville Syrjälä [Wed, 2 Oct 2019 16:25:05 +0000 (19:25 +0300)]
drm/i915/mst: Document the userspace fail with possible_crtcs
To avoid accidentally breaking things in the future add a
comment explaining why we misconfigure the pipe_mask.
Also toss in a TODO for investigating a single encoder
approach as opposed to the encoder-per-pipe approach.
v2: Drop a bogus TODO comment
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191002162505.30716-6-ville.syrjala@linux.intel.com
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Ville Syrjälä [Wed, 2 Oct 2019 16:25:04 +0000 (19:25 +0300)]
drm/i915: Simplify pipe_mask setup even further
Just set pipe_mask=~0 for the non-special cases where any pipe
will do. intel_encoder_possible_crtcs() will anyway drop out
anything that doesn't exist.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191002162505.30716-5-ville.syrjala@linux.intel.com
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Ville Syrjälä [Wed, 2 Oct 2019 16:25:03 +0000 (19:25 +0300)]
drm/i915: Allow ICL+ DSI on any pipe
There are no longer any pipe<->DSI port limitations on icl+.
Populate the pipe_mask accordingly.
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191002162505.30716-4-ville.syrjala@linux.intel.com
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Ville Syrjälä [Wed, 2 Oct 2019 16:25:02 +0000 (19:25 +0300)]
drm/i915: s/crtc_mask/pipe_mask/
Rename the encoder->crtc_mask to encoder->pipe_mask to better
reflect what it actually contains.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191002162505.30716-3-ville.syrjala@linux.intel.com
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Ville Syrjälä [Wed, 2 Oct 2019 16:25:01 +0000 (19:25 +0300)]
drm/i915: Simplify LVDS crtc_mask setup
We don't need to special case PCH vs. gen4 when setting up the LVDS
crtc_mask. Just claim pipes A|B|C work and
intel_encoder_possible_crtcs() will drop out any crtc that doesn't
exist.
v2: Put the special case first to match what most other encoders do
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191002162505.30716-2-ville.syrjala@linux.intel.com
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Daniele Ceraolo Spurio [Sat, 26 Oct 2019 00:35:06 +0000 (17:35 -0700)]
drm/i915/uc: define GuC and HuC binaries for TGL
GuC 35.2.0 and HuC 7.0.3 are the first production releases for TGL.
GuC 35.2 for Gen12 is interface-compatible with 33.0 on older Gens,
because the differences are related to additional blocks/commands in
the interface to support new Gen12 features. These parts of the
interface will be added when the relevant features are enabled.
v2: fix typos (Michal)
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191026003507.21769-1-daniele.ceraolospurio@intel.com
Ville Syrjälä [Tue, 29 Oct 2019 14:55:26 +0000 (16:55 +0200)]
drm/i915: Stop frobbing crtc->base.mode
The core no longer uses drm_crtc_state::mode with atomic drivers,
so let's stop frobbing it in the driver. For the user mode readout
we'll just use an on stack mode.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191029145526.10308-1-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Ville Syrjälä [Tue, 29 Oct 2019 13:23:23 +0000 (15:23 +0200)]
drm/i915: Nuke 'mode' argument to intel_get_load_detect_pipe()
We always pass mode==NULL to intel_get_load_detect_pipe(). Remove
the pointless function argument.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191029132323.18113-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Imre Deak [Mon, 28 Oct 2019 18:15:17 +0000 (20:15 +0200)]
drm/i915: Avoid HPD poll detect triggering a new detect cycle
For the HPD interrupt functionality the HW depends on power wells in the
display core domain to be on. Accordingly when enabling these power
wells the HPD polling logic will force an HPD detection cycle to account
for hotplug events that may have happened when such a power well was
off.
Thus a detect cycle started by polling could start a new detect cycle if
a power well in the display core domain gets enabled during detect and
stays enabled after detect completes. That in turn can lead to a
detection cycle runaway.
To prevent re-triggering a poll-detect cycle make sure we drop all power
references we acquired during detect synchronously by the end of detect.
This will let the poll-detect logic continue with polling (matching the
off state of the corresponding power wells) instead of scheduling a new
detection cycle.
Fixes:
6cfe7ec02e85 ("drm/i915: Remove the unneeded AUX power ref from intel_dp_detect()")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=112125
Reported-and-tested-by: Val Kulkov <val.kulkov@gmail.com>
Reported-and-tested-by: wangqr <wqr.prg@gmail.com>
Cc: Val Kulkov <val.kulkov@gmail.com>
Cc: wangqr <wqr.prg@gmail.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191028181517.22602-1-imre.deak@intel.com
Chris Wilson [Wed, 30 Oct 2019 10:38:23 +0000 (10:38 +0000)]
drm/i915/gt: Always track callers to intel_rps_mark_interactive()
During startup, we may find ourselves in an interesting position where
we haven't fully enabled RPS before the display starts trying to use it.
This may lead to an imbalance in our "interactive" counter:
<3>[ 4.813326] intel_rps_mark_interactive:652 GEM_BUG_ON(!rps->power.interactive)
<4>[ 4.813396] ------------[ cut here ]------------
<2>[ 4.813398] kernel BUG at drivers/gpu/drm/i915/gt/intel_rps.c:652!
<4>[ 4.813430] invalid opcode: 0000 [#1] PREEMPT SMP PTI
<4>[ 4.813438] CPU: 1 PID: 18 Comm: kworker/1:0H Not tainted 5.4.0-rc5-CI-CI_DRM_7209+ #1
<4>[ 4.813447] Hardware name: /NUC7i5BNB, BIOS BNKBL357.86A.0054.2017.1025.1822 10/25/2017
<4>[ 4.813525] Workqueue: events_highpri intel_atomic_cleanup_work [i915]
<4>[ 4.813589] RIP: 0010:intel_rps_mark_interactive+0xb3/0xc0 [i915]
<4>[ 4.813597] Code: bc 3f de e0 48 8b 35 84 2e 24 00 49 c7 c0 f3 d4 4e a0 b9 8c 02 00 00 48 c7 c2 80 9c 48 a0 48 c7 c7 3e 73 34 a0 e8 8d 3b e5 e0 <0f> 0b 90 66 2e 0f 1f 84 00 00 00 00 00 80 bf c0 00 00 00 00 74 32
<4>[ 4.813616] RSP: 0018:
ffffc900000efe00 EFLAGS:
00010286
<4>[ 4.813623] RAX:
000000000000000e RBX:
ffff8882583cc7f0 RCX:
0000000000000000
<4>[ 4.813631] RDX:
0000000000000001 RSI:
0000000000000008 RDI:
ffff888275969c00
<4>[ 4.813639] RBP:
0000000000000000 R08:
0000000000000008 R09:
ffff888275ace000
<4>[ 4.813646] R10:
ffffc900000efe00 R11:
ffff888275969c00 R12:
ffff8882583cc8d8
<4>[ 4.813654] R13:
ffff888276abce00 R14:
0000000000000000 R15:
ffff88825e878860
<4>[ 4.813662] FS:
0000000000000000(0000) GS:
ffff888276a80000(0000) knlGS:
0000000000000000
<4>[ 4.813672] CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
<4>[ 4.813678] CR2:
00007f051d5ca0a8 CR3:
0000000262f48001 CR4:
00000000003606e0
<4>[ 4.813686] Call Trace:
<4>[ 4.813755] intel_cleanup_plane_fb+0x4e/0x60 [i915]
<4>[ 4.813764] drm_atomic_helper_cleanup_planes+0x4d/0x70
<4>[ 4.813833] intel_atomic_cleanup_work+0x15/0x80 [i915]
<4>[ 4.813842] process_one_work+0x26a/0x620
<4>[ 4.813850] worker_thread+0x37/0x380
<4>[ 4.813857] ? process_one_work+0x620/0x620
<4>[ 4.813864] kthread+0x119/0x130
<4>[ 4.813870] ? kthread_park+0x80/0x80
<4>[ 4.813878] ret_from_fork+0x3a/0x50
<4>[ 4.813887] Modules linked in: i915(+) mei_hdcp x86_pkg_temp_thermal coretemp crct10dif_pclmul crc32_pclmul btusb btrtl btbcm btintel snd_hda_intel snd_intel_nhlt snd_hda_codec bluetooth snd_hwdep snd_hda_core ghash_clmulni_intel snd_pcm e1000e ecdh_generic ecc ptp pps_core mei_me mei prime_numbers
<4>[ 4.813934] ---[ end trace
c13289af88174ffc ]---
The solution employed is to not worry about RPS state and keep the tally
of the interactive counter separate. When we do enable RPS, we will then
take the display activity into account.
Fixes:
3e7abf814193 ("drm/i915: Extract GT render power state management")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Andi Shyti <andi.shyti@intel.com>
Acked-by: Andi Shyti <andi.shyti@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191030103827.2413-1-chris@chris-wilson.co.uk
Mika Kuoppala [Tue, 29 Oct 2019 16:38:41 +0000 (18:38 +0200)]
drm/i915/tgl: Add gam instdone
This has been asked from us already. Prepare for the next
time.
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20191029163841.5224-2-mika.kuoppala@linux.intel.com
Mika Kuoppala [Tue, 29 Oct 2019 16:38:40 +0000 (18:38 +0200)]
drm/i915/tgl: Add SFC instdone to error state
On debugging media workload hangs, sfc instdone
might prove useful in future. Be prepared.
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20191029163841.5224-1-mika.kuoppala@linux.intel.com
Lucas De Marchi [Tue, 29 Oct 2019 03:50:49 +0000 (20:50 -0700)]
drm/i915/tgl: add support to one DP-MST stream
This is the minimum change to support 1 (and only 1) DP-MST monitor
connected on Tiger Lake. This change was isolated from previous patch
from José. In order to support more streams we will need to create a
master-slave relation on the transcoders and that is not currently
working yet.
v2: remove unused macro and use REG_FIELD_PREP() (Ville)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191029035049.5907-1-lucas.demarchi@intel.com
Chris Wilson [Tue, 29 Oct 2019 20:23:38 +0000 (20:23 +0000)]
drm/i915/gem: Make context persistence optional
Our existing behaviour is to allow contexts and their GPU requests to
persist past the point of closure until the requests are complete. This
allows clients to operate in a 'fire-and-forget' manner where they can
setup a rendering pipeline and hand it over to the display server and
immediately exit. As the rendering pipeline is kept alive until
completion, the display server (or other consumer) can use the results
in the future and present them to the user.
The compute model is a little different. They have little to no buffer
sharing between processes as their kernels tend to operate on a
continuous stream, feeding the results back to the client application.
These kernels operate for an indeterminate length of time, with many
clients wishing that the kernel was always running for as long as they
keep feeding in the data, i.e. acting like a DSP.
Not all clients want this persistent "desktop" behaviour and would prefer
that the contexts are cleaned up immediately upon closure. This ensures
that when clients are run without hangchecking (e.g. for compute kernels
of indeterminate runtime), any GPU hang or other unexpected workloads
are terminated with the process and does not continue to hog resources.
The default behaviour for new contexts is the legacy persistence mode,
as some desktop applications are dependent upon the existing behaviour.
New clients will have to opt in to immediate cleanup on context
closure. If the hangchecking modparam is disabled, so is persistent
context support -- all contexts will be terminated on closure.
We expect this behaviour change to be welcomed by compute users, who
have often been caught between a rock and a hard place. They disable
hangchecking to avoid their kernels being "unfairly" declared hung, but
have also experienced true hangs that the system was then unable to
clean up. Naturally, this leads to bug reports.
Testcase: igt/gem_ctx_persistence
Link: https://github.com/intel/compute-runtime/pull/228
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Jon Bloomfield <jon.bloomfield@intel.com>
Reviewed-by: Jon Bloomfield <jon.bloomfield@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Acked-by: Jason Ekstrand <jason@jlekstrand.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20191029202338.8841-1-chris@chris-wilson.co.uk
Matt Roper [Tue, 29 Oct 2019 17:31:02 +0000 (10:31 -0700)]
drm/i915: Provide more information on DP AUX failures
We're seeing some failures where an aux transaction still shows as
'busy' well after the timeout limit that the hardware is supposed to
enforce. Improve the error message so that we can see exactly which aux
channel this error happened on and what the status bits were during this
case that isn't supposed to happen.
v2:
- Make timeout a const variable so that the timeout & message will
match if we decide to change it in the future. (Lucas)
- Don't bother testing intel_dp->aux.name for NULL. (Lucas)
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191029173102.9451-1-matthew.d.roper@intel.com
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
José Roberto de Souza [Sat, 26 Oct 2019 00:13:23 +0000 (17:13 -0700)]
drm/i915/display/cnl+: Handle fused off DSC
DSC could be fused off, so not all GEN10+ platforms will support it.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Martin Peres <martin.peres@linux.intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191026001323.216052-5-jose.souza@intel.com
José Roberto de Souza [Sat, 26 Oct 2019 00:13:22 +0000 (17:13 -0700)]
drm/i915/display/icl+: Check if DMC is fused off
Check if DMC is fused off and handle it.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Martin Peres <martin.peres@linux.intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191026001323.216052-4-jose.souza@intel.com
José Roberto de Souza [Sat, 26 Oct 2019 00:13:21 +0000 (17:13 -0700)]
drm/i915/display: Check if FBC is fused off
Check if FBC is fused off and handle it.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Martin Peres <martin.peres@linux.intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191026001323.216052-3-jose.souza@intel.com
José Roberto de Souza [Sat, 26 Oct 2019 00:13:20 +0000 (17:13 -0700)]
drm/i915/display: Handle fused off HDCP
HDCP could be fused off, so not all GEN9+ platforms will support it.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Martin Peres <martin.peres@linux.intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191026001323.216052-2-jose.souza@intel.com
José Roberto de Souza [Sat, 26 Oct 2019 00:13:19 +0000 (17:13 -0700)]
drm/i915: Add two spaces before the SKL_DFSM registers
The next patches are going to touch this registers so here already
fixing it for older registers and make it consistent with most of
the other registers in this file.
Cc: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191026001323.216052-1-jose.souza@intel.com
Lionel Landwerlin [Tue, 29 Oct 2019 14:28:26 +0000 (16:28 +0200)]
drm/i915/perf: ensure selftests select valid format
Gen12 only support a single report format :
I915_OA_FORMAT_A32u40_A4u32_B8_C8
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Fixes:
00a7f0d7155c ("drm/i915/tgl: Add perf support on TGL")
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20191029142826.20014-1-lionel.g.landwerlin@intel.com
Matt Roper [Fri, 25 Oct 2019 23:06:23 +0000 (16:06 -0700)]
drm/i915/tgl: Add AUX B & C to DC_OFF_POWER_DOMAINS
Our TGL CI platforms are running into cases where aux transactions have
failed to complete or declare a timeout well after the timeout limit
that the hardware is supposed to enforce. From the logs it appears that
these failures arise when aux transactions happen after we've entered
DC6:
<7> [622.523650] [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [622.523685] [drm:gen9_set_dc_state [i915]] Setting DC state from 00 to 02
...
<3> [622.535753] [drm:intel_dp_aux_xfer [i915]] *ERROR* dp aux hw did not signal timeout!
<3> [622.547745] [drm:intel_dp_aux_xfer [i915]] *ERROR* dp aux hw did not signal timeout!
<3> [622.559746] [drm:intel_dp_aux_xfer [i915]] *ERROR* dp aux hw did not signal timeout!
<3> [622.571744] [drm:intel_dp_aux_xfer [i915]] *ERROR* dp aux hw did not signal timeout!
<3> [622.583743] [drm:intel_dp_aux_xfer [i915]] *ERROR* dp aux hw did not signal timeout!
<3> [622.583780] [drm:intel_dp_aux_xfer [i915]] *ERROR* dp_aux_ch not done status 0xad400bff
<7> [622.863725] [drm:drm_dp_dpcd_access] Too many retries, giving up. First error: -110
On TGL AUX B & C are in PG1 (managed by the DMC firmware) rather
than PG3 as they were on ICL, so allowing DC6 means the DMC firmware
might shut off the power wells behind our backs when we're trying to use
them.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191025230623.27829-6-matthew.d.roper@intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Matt Roper [Sat, 26 Oct 2019 05:12:26 +0000 (22:12 -0700)]
drm/i915: Drop unused AUX register offsets
We reference DP AUX registers via the DP_AUX_CH_CTL() and
DP_AUX_CH_DATA() macros that calculate all the register offsets for us
automatically; there's no need to explicitly define every offset in
i915_reg.h if they're never going to be used by the driver code.
v2: Apparently GVT was directly using these raw definitions in a couple
places. Switch GVT code over to using our preferred macros.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com> #v1
Link: https://patchwork.freedesktop.org/patch/msgid/20191026051226.30807-1-matthew.d.roper@intel.com
Chris Wilson [Tue, 29 Oct 2019 09:16:32 +0000 (09:16 +0000)]
drm/i915/gt: Make timeslice duration configurable
Execlists uses a scheduling quantum (a timeslice) to alternate execution
between ready-to-run contexts of equal priority. This ensures that all
users (though only if they of equal importance) have the opportunity to
run and prevents livelocks where contexts may have implicit ordering due
to userspace semaphores. However, not all workloads necessarily benefit
from timeslicing and in the extreme some sysadmin may want to disable or
reduce the timeslicing granularity.
The timeslicing mechanism can be compiled out^W^W disabled (but should
DCE!) with
./scripts/config --set-val DRM_I915_TIMESLICE_DURATION 0
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191029091632.26281-1-chris@chris-wilson.co.uk
Janusz Krzysztofik [Tue, 29 Oct 2019 10:20:36 +0000 (11:20 +0100)]
drm/i915: Rename "inject_load_failure" module parameter
Commit
f2db53f14d3d ("drm/i915: Replace "_load" with "_probe"
consequently") deliberately left the name of the module parameter
unchanged as that would require a corresponding change on IGT size.
Now as the IGT side change has been submitted, complete the switch to
the "probe" nomenclature.
Suggested-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Janusz Krzysztofik <janusz.krzysztofik@linux.intel.com>
Cc: Michał Wajdeczko <michal.wajdeczko@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Piotr Piórkowski <piotr.piorkowski@intel.com>
Cc: Tomasz Lis <tomasz.lis@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20191029102036.6326-3-janusz.krzysztofik@linux.intel.com
Janusz Krzysztofik [Tue, 29 Oct 2019 10:20:35 +0000 (11:20 +0100)]
drm/i915: Fix i915_inject_load_error() name to read *_probe_*
Commit
50d84418f586 ("drm/i915: Add i915 to i915_inject_probe_failure")
introduced new functions unfortunately named incompatibly with rules
established by commit
f2db53f14d3d ("drm/i915: Replace "_load" with
"_probe" consequently"). Fix it for consistency.
Suggested-by: Michał Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Janusz Krzysztofik <janusz.krzysztofik@linux.intel.com>
Cc: Michał Wajdeczko <michal.wajdeczko@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Piotr Piórkowski <piotr.piorkowski@intel.com>
Cc: Tomasz Lis <tomasz.lis@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20191029102036.6326-2-janusz.krzysztofik@linux.intel.com
Ville Syrjälä [Mon, 28 Oct 2019 11:30:31 +0000 (13:30 +0200)]
drm/i915: Fix i845/i865 cursor width
The change from the uapi coordinates to the internal coordinates
broke the cursor on i845/i865 due to src and dst getting swapped.
Fix it.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes:
3a612765f423 ("drm/i915: Remove cursor use of properties for coordinates")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191028113036.27553-1-ville.syrjala@linux.intel.com
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Lionel Landwerlin [Fri, 25 Oct 2019 19:37:46 +0000 (12:37 -0700)]
drm/i915/tgl: Add perf support on TGL
The design of the OA unit has been split into several units. We now
have a global unit (OAG) and a render specific unit (OAR). This leads
to some changes on how we program things. Some details :
OAR:
- has its own set of counter registers, they are per-context
saved/restored
- counters are not written to the circular OA buffer
- a snapshot of the counters can be acquired with
MI_RECORD_PERF_COUNT, or a single counter can be read with
MI_STORE_REGISTER_MEM.
OAG:
- has global counters that increment across context switches
- counters are written into the circular OA buffer (if requested)
v2: Fix checkpatch warnings on code style (Lucas)
v3: (Umesh)
- Update register from which tail, status and head are read
- Update logic to sample context reports
- Update whitelist mux and b counter regs
v4: Fix a bug when updating context image for new contexts (Umesh)
v5: Squash patch enabling save/restore of counters into context image
We want this so we can preempt performance queries and keep the
system responsive even when long running queries are ongoing. We
avoid doing it for all contexts.
- use LRI to modify context control (Chris)
- use MASKED_FIELD to program just the masked bits (Chris)
- disable save/restore of counters on cleanup (Chris)
v6: Do not use implicit parameters (Chris)
BSpec: 28727, 30021
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Signed-off-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Acked-by: Chris Wilson <chris.p.wilson@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191025193746.47155-2-umesh.nerlige.ramappa@intel.com
Umesh Nerlige Ramappa [Fri, 25 Oct 2019 19:37:45 +0000 (12:37 -0700)]
drm/i915/perf: Add helper macros for comparing with whitelisted registers
Add helper macros for range and equality comparisons and use them to
check with whitelisted registers in oa configurations.
Signed-off-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191025193746.47155-1-umesh.nerlige.ramappa@intel.com
Matthew Auld [Tue, 29 Oct 2019 09:58:56 +0000 (09:58 +0000)]
drm/i915/selftests: check for missing aperture
We may be missing support for the mappable aperture on some platforms.
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20191029095856.25431-7-matthew.auld@intel.com
Matthew Auld [Tue, 29 Oct 2019 09:58:55 +0000 (09:58 +0000)]
drm/i915: don't allocate the ring in stolen if we lack aperture
Since we have no way access it from the CPU. For such cases just
fallback to internal objects.
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20191029095856.25431-6-matthew.auld@intel.com
Michal Wajdeczko [Tue, 29 Oct 2019 09:58:54 +0000 (09:58 +0000)]
drm/i915: Don't try to place HWS in non-existing mappable region
HWS placement restrictions can't just rely on HAS_LLC flag.
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20191029095856.25431-5-matthew.auld@intel.com
Daniele Ceraolo Spurio [Tue, 29 Oct 2019 09:58:53 +0000 (09:58 +0000)]
drm/i915: error capture with no ggtt slot
If the aperture is not available in HW we can't use a ggtt slot and wc
copy, so fall back to regular kmap.
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Abdiel Janulgue <abdiel.janulgue@linux.intel.com>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20191029095856.25431-4-matthew.auld@intel.com
Daniele Ceraolo Spurio [Tue, 29 Oct 2019 09:58:52 +0000 (09:58 +0000)]
drm/i915: set num_fence_regs to 0 if there is no aperture
We can't fence anything without aperture.
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Stuart Summers <stuart.summers@intel.com>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20191029095856.25431-3-matthew.auld@intel.com
Daniele Ceraolo Spurio [Tue, 29 Oct 2019 09:58:51 +0000 (09:58 +0000)]
drm/i915: do not map aperture if it is not available.
Skip both setup and cleanup of the aperture mapping if the HW doesn't
have an aperture bar.
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20191029095856.25431-2-matthew.auld@intel.com
Daniele Ceraolo Spurio [Tue, 29 Oct 2019 09:58:50 +0000 (09:58 +0000)]
drm/i915: define i915_ggtt_has_aperture
The following patches in the series will use it to avoid certain
operations when the mappable aperture is not available in HW.
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20191029095856.25431-1-matthew.auld@intel.com
Matthew Auld [Mon, 28 Oct 2019 22:03:25 +0000 (22:03 +0000)]
drm/i915/blt: fixup block_size rounding
There is nothing to say that the obj->base.size is actually a multiple
of the block_size.
v2: Use round_up() as block_size is a power-of-two
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20191028220325.9325-1-chris@chris-wilson.co.uk
Chris Wilson [Mon, 28 Oct 2019 20:30:12 +0000 (20:30 +0000)]
drm/i915/gem: Limit the blitter sizes to ensure low preemption latency
Currently we insert a arbitration point every 128MiB during a blitter
copy. At 8GiB/s, this is around 30ms. This is a little on the large side
if we need to inject a high priority work, so reduced it down to 8MiB or
roughly 1ms.
v2: Don't forget both fill/copy.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191028203012.14566-1-chris@chris-wilson.co.uk
Michal Wajdeczko [Mon, 28 Oct 2019 16:45:20 +0000 (16:45 +0000)]
drm/i915/execlists: Use vfunc to check engine submission mode
While processing CSB there is no need to look at GuC submission
settings, just check if engine is configured for execlists mode.
While today GuC submission is disabled it's settings are still
based on modparam values that might not correctly reflect actual
submission status in case of any fallback. Until that is fully
fixed, use alternate method to confirm that engine really runs in
execlists mode by comparing set_default_submission vfunc.
v2: add other immediate use of new helper
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Janusz Krzysztofik <janusz.krzysztofik@linux.intel.com>
Reviewed-by: Janusz Krzysztofik <janusz.krzysztofik@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20191028164520.31772-1-michal.wajdeczko@intel.com
Chris Wilson [Mon, 28 Oct 2019 14:26:52 +0000 (14:26 +0000)]
drm/i915/display: Mark conn as initialised by iterator
smatch complains about
drivers/gpu/drm/i915//display/intel_display.c:14403 intel_set_dp_tp_ctl_normal() error: uninitialized symbol 'conn'.
because it has no way to determine that the loop must have an entry.
Tell the static analysers to ignore the local, it will always be set.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191028142652.1987-2-chris@chris-wilson.co.uk
Chris Wilson [Mon, 28 Oct 2019 14:26:51 +0000 (14:26 +0000)]
drm/i915/selftests: Initialise ret
Keep smatch quiet,
drivers/gpu/drm/i915//gem/selftests/i915_gem_context.c:1268 __igt_ctx_sseu() error: uninitialized symbol 'ret'.
drivers/gpu/drm/i915//gem/selftests/i915_gem_context.c:1280 __igt_ctx_sseu() error: uninitialized symbol 'ret'.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191028142652.1987-1-chris@chris-wilson.co.uk
Chris Wilson [Fri, 25 Oct 2019 13:59:43 +0000 (14:59 +0100)]
drm/i915/selftests: Initialise err in case there are no engines!
drivers/gpu/drm/i915//gt/selftest_engine_heartbeat.c:255 live_heartbeat_fast() error: uninitialized symbol 'err'.
drivers/gpu/drm/i915//gt/selftest_engine_heartbeat.c:320 live_heartbeat_off() error: uninitialized symbol 'err'.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191025135943.12524-2-chris@chris-wilson.co.uk
Chris Wilson [Mon, 28 Oct 2019 12:41:25 +0000 (12:41 +0000)]
drm/i915/execlists: Simply walk back along request timeline on reset
The request's timeline will only contain requests from this context, in
order of execution. Therefore, we can simply look back along this
timeline to find the currently executing request.
If we do find that the current context has completed its last request,
that does not imply that all requests are completed in the context, so
only advance the ring->head up to the end of the known completions!
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191028124125.25176-1-chris@chris-wilson.co.uk
Chris Wilson [Mon, 28 Oct 2019 12:18:03 +0000 (12:18 +0000)]
drm/i915/selftests: Check a few more fixed locations within the context image
As we use hard coded offsets for a few locations within the context
image, include those in the selftests to assert that they are valid.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191028121803.29408-1-chris@chris-wilson.co.uk
Matt Roper [Thu, 24 Oct 2019 17:30:23 +0000 (10:30 -0700)]
drm/i915/tgl: Handle AUX interrupts for TC ports
We're currently only processing AUX interrupts on the combo ports; make
sure we handle the TC ports as well.
v2: Drop stale comment
Fixes:
f663769a5eef ("drm/i915/tgl: initialize TC and TBT ports")
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191024173023.22113-1-matthew.d.roper@intel.com
Chris Wilson [Sun, 27 Oct 2019 22:58:05 +0000 (22:58 +0000)]
drm/i915/selftests: Exercise adjusting rpcs over all render-class engines
Iterate over all user-accessible render engines when checking whether
they can be adjusted for sseu.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191027225808.19437-2-chris@chris-wilson.co.uk
Chris Wilson [Sun, 27 Oct 2019 22:58:08 +0000 (22:58 +0000)]
drm/i915/selftests: Select a random engine for testing memory regions
Use any blitter engine at random for prefilling the memory region.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191027225808.19437-5-chris@chris-wilson.co.uk
Chris Wilson [Sun, 27 Oct 2019 17:55:05 +0000 (17:55 +0000)]
drm/i915/gt: Tidy up rps irq handler to use intel_gt
Since the rps is tied to its intel_gt, use that backpointer to find the
right engine rather than delving into i915.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Andi Shyti <andi.shyti@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191027175505.25470-1-chris@chris-wilson.co.uk