git.osdn.net Git - uclinux-h8/linux.git/log

ath11k: add hw_param for wakeup_mhi

Wakeup mhi is needed before pci_read/write only for QCA6390 and WCN6855. Since
wakeup & release mhi is enabled for all hardwares, below mhi assert is seen in
QCN9074 when doing 'rmmod ath11k_pci':

Kernel panic - not syncing: dev_wake != 0
CPU: 2 PID: 13535 Comm: procd Not tainted 4.4.60 #1
Hardware name: Generic DT based system
[<80316dac>] (unwind_backtrace) from [<80313700>] (show_stack+0x10/0x14)
[<80313700>] (show_stack) from [<805135dc>] (dump_stack+0x7c/0x9c)
[<805135dc>] (dump_stack) from [<8032136c>] (panic+0x84/0x1f8)
[<8032136c>] (panic) from [<80549b24>] (mhi_pm_disable_transition+0x3b8/0x5b8)
[<80549b24>] (mhi_pm_disable_transition) from [<80549ddc>] (mhi_power_down+0xb8/0x100)
[<80549ddc>] (mhi_power_down) from [<7f5242b0>] (ath11k_mhi_op_status_cb+0x284/0x3ac [ath11k_pci])
[E][__mhi_device_get_sync] Did not enter M0 state, cur_state:RESET pm_state:SHUTDOWN Process
[E][__mhi_device_get_sync] Did not enter M0 state, cur_state:RESET pm_state:SHUTDOWN Process
[E][__mhi_device_get_sync] Did not enter M0 state, cur_state:RESET pm_state:SHUTDOWN Process
[<7f5242b0>] (ath11k_mhi_op_status_cb [ath11k_pci]) from [<7f524878>] (ath11k_mhi_stop+0x10/0x20 [ath11k_pci])
[<7f524878>] (ath11k_mhi_stop [ath11k_pci]) from [<7f525b94>] (ath11k_pci_power_down+0x54/0x90 [ath11k_pci])
[<7f525b94>] (ath11k_pci_power_down [ath11k_pci]) from [<8056b2a8>] (pci_device_shutdown+0x30/0x44)
[<8056b2a8>] (pci_device_shutdown) from [<805cfa0c>] (device_shutdown+0x124/0x174)
[<805cfa0c>] (device_shutdown) from [<8033aaa4>] (kernel_restart+0xc/0x50)
[<8033aaa4>] (kernel_restart) from [<8033ada8>] (SyS_reboot+0x178/0x1ec)
[<8033ada8>] (SyS_reboot) from [<80301b80>] (ret_fast_syscall+0x0/0x34)

Hence, disable wakeup/release mhi using hw_param for other hardwares.

Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01060-QCAHKSWPL_SILICONZ-1

Fixes: a05bd8513335 ("ath11k: read and write registers below unwindowed address")
Signed-off-by: Seevalamuthu Mariappan <quic_seevalam@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1636702019-26142-1-git-send-email-quic_seevalam@quicinc.com

ath11k: reset RSN/WPA present state for open BSS

The ath11k driver is caching the information about RSN/WPA IE in the
configured beacon template. The cached information is used during
associations to figure out whether 4-way PKT/2-way GTK peer flags need to
be set or not.

But the code never cleared the state when no such IE was found. This can
for example happen when moving from an WPA/RSN to an open setup. The
(seemingly connected) peer was then not able to communicate over the
link because the firmware assumed a different (encryption enabled) state
for the peer.

Tested-on: IPQ6018 hw1.0 AHB WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1

Fixes: 01e34233c645 ("ath11k: fix wmi peer flags in peer assoc command")
Cc: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Reported-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Karthikeyan Kathirvel <kathirve@codeaurora.org>
[sven@narfation.org: split into separate patches, clean up commit message]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211115100441.33771-2-sven@narfation.org

ath11k: clear the keys properly via DISABLE_KEY

DISABLE_KEY sets the key_len to 0, firmware will not delete the keys if
key_len is 0. Changing from security mode to open mode will cause mcast
to be still encrypted without vdev restart.

Set the proper key_len for DISABLE_KEY cmd to clear the keys in
firmware.

Tested-on: IPQ6018 hw1.0 AHB WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1

Fixes: d5c65159f289 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Reported-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Karthikeyan Kathirvel <kathirve@codeaurora.org>
[sven@narfation.org: split into separate patches, clean up commit message]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211115100441.33771-1-sven@narfation.org

ath11k: add support for BSS color change

Whenever the MAC detects a color collision, or any of
its associated stations detects one, the firmware will
send out an event. Add the code to parse and handle
this event and pass the data up to mac80211.

The firmware does not provide an offload feature such
as the one used for CSA. The color change process is
hence triggered via the beacon offload tx completion
events sent out by firmware.

BSS color feature is enabled depending on service flag
advertised by firmware, based on which color change
functionality is invoked.

Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-00680-QCAHKSWPL_SILICONZ-1

Signed-off-by: John Crispin <john@phrozen.org>
Co-developed-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1635178254-17732-1-git-send-email-quic_ramess@quicinc.com

ath11k: add string type to search board data in board-2.bin for WCN6855

Currently ath11k only support string type with bus, chip id and board id
such as "bus=ahb,qmi-chip-id=1,qmi-board-id=4" for ahb bus chip and
"bus=pci,qmi-chip-id=0,qmi-board-id=255" for PCIe bus chip in
board-2.bin. For WCN6855, it is not enough to distinguish all different
chips.

This is to add a new string type which include bus, chip id, board id,
vendor, device, subsystem-vendor and subsystem-device for WCN6855.

ath11k will first load board-2.bin and search in it for the board data
with the above parameters, if matched one board data, then download it
to firmware, if not matched any one, then ath11k will download the file
board.bin to firmware.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1

Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Jouni Malinen <quic_jouni@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211111065340.20187-1-quic_wgong@quicinc.com

ath11k: Fix crash caused by uninitialized TX ring

Commit 31582373a4a8 ("ath11k: Change number of TCL rings to one for
QCA6390") avoids initializing the other entries of dp->tx_ring cause
the corresponding TX rings on QCA6390/WCN6855 are not used, but leaves
those ring masks in ath11k_hw_ring_mask_qca6390.tx unchanged. Normally
this is OK because we will only get interrupts from the first TX ring
on these chips and thus only the first entry of dp->tx_ring is involved.

In case of one MSI vector, all DP rings share the same IRQ. For each
interrupt, all rings have to be checked, which means the other entries
of dp->tx_ring are involved. However since they are not initialized,
system crashes.

Fix this issue by simply removing those ring masks.

crash stack:
[  102.907438] BUG: kernel NULL pointer dereference, address: 0000000000000028
[  102.907447] #PF: supervisor read access in kernel mode
[  102.907451] #PF: error_code(0x0000) - not-present page
[  102.907453] PGD 1081f0067 P4D 1081f0067 PUD 1081f1067 PMD 0
[  102.907460] Oops: 0000 [#1] SMP DEBUG_PAGEALLOC NOPTI
[  102.907465] CPU: 0 PID: 3511 Comm: apt-check Kdump: loaded Tainted: G            E     5.15.0-rc4-wt-ath+ #20
[  102.907470] Hardware name: AMD Celadon-RN/Celadon-RN, BIOS RCD1005E 10/08/2020
[  102.907472] RIP: 0010:ath11k_dp_tx_completion_handler+0x201/0x830 [ath11k]
[  102.907497] Code: 3c 24 4e 8d ac 37 10 04 00 00 4a 8d bc 37 68 04 00 00 48 89 3c 24 48 63 c8 89 83 84 18 00 00 48 c1 e1 05 48 03 8b 78 18 00 00 <8b> 51 08 89 d6 83 e6 07 89 74 24 24 83 fe 03 74 04 85 f6 75 63 41
[  102.907501] RSP: 0000:ffff9b7340003e08 EFLAGS: 00010202
[  102.907505] RAX: 0000000000000001 RBX: ffff8e21530c0100 RCX: 0000000000000020
[  102.907508] RDX: 0000000000000000 RSI: 00000000fffffe00 RDI: ffff8e21530c1938
[  102.907511] RBP: ffff8e21530c0000 R08: 0000000000000001 R09: 0000000000000000
[  102.907513] R10: ffff8e2145534c10 R11: 0000000000000001 R12: ffff8e21530c2938
[  102.907515] R13: ffff8e21530c18e0 R14: 0000000000000100 R15: ffff8e21530c2978
[  102.907518] FS:  00007f5d4297e740(0000) GS:ffff8e243d600000(0000) knlGS:0000000000000000
[  102.907521] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  102.907524] CR2: 0000000000000028 CR3: 00000001034ea000 CR4: 0000000000350ef0
[  102.907527] Call Trace:
[  102.907531]  <IRQ>
[  102.907537]  ath11k_dp_service_srng+0x5c/0x2f0 [ath11k]
[  102.907556]  ath11k_pci_ext_grp_napi_poll+0x21/0x70 [ath11k_pci]
[  102.907562]  __napi_poll+0x2c/0x160
[  102.907570]  net_rx_action+0x251/0x310
[  102.907576]  __do_softirq+0x107/0x2fc
[  102.907585]  irq_exit_rcu+0x74/0x90
[  102.907593]  common_interrupt+0x83/0xa0
[  102.907600]  </IRQ>
[  102.907601]  asm_common_interrupt+0x1e/0x40

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1

Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211026011605.58615-1-quic_bqiang@quicinc.com

ath11k: add trace log support

This change is to add trace log support for,
        * WMI events
        * WMI commands
        * ath11k_dbg messages
        * ath11k_dbg_dump messages
        * ath11k_log_info messages
        * ath11k_log_warn messages
        * ath11k_log_err messages

Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-00652-QCAHKSWPL_SILICONZ-1

Signed-off-by: Venkateswara Naralasetty <quic_vnaralas@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1636439755-30419-1-git-send-email-quic_vnaralas@quicinc.com

ath11k: Add missing qmi_txn_cancel()

Currently many functions do not follow this guidance when
qmi_send_request() fails, therefore add missing
qmi_txn_cancel() in the qmi_send_request() error path.

Also remove initialization on 'struct qmi_txn'
since qmi_tx_init() performs all necessary initialization.

Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01838-QCAHKSWPL_SILICONZ-1

Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1635857558-21733-1-git-send-email-akolli@codeaurora.org

ath11k: use cache line aligned buffers for dbring

The DMA buffers of dbring which is used for spectral/cfr
starts at certain offset from original kmalloc() returned buffer.
This is not cache line aligned.
And also driver tries to access the data that is immediately before
this offset address (i.e. buff->paddr) after doing dma map.
This will cause cache line sharing issues and data corruption,
if CPU happen to write back cache after HW has dma'ed the data.

Fix this by mapping a cache line aligned buffer to dma.

Tested on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1

Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1635831693-15962-1-git-send-email-quic_ramess@quicinc.com

ath11k: Disabling credit flow for WMI path

Firmware credit flow control is enabled for WMI control services,
which expects available tokens should be acquired before sending a
command to the target. Also the token gets released when firmware
receives the command.

This credit-based flow limits driver to send WMI command only
when the token available which is causing WMI commands to timeout and
return -EAGAIN, whereas firmware has enough capability to process the
WMI command. To fix this Tx starvation issue, introduce the ability to
disable the credit flow for the WMI path.

The driver sends WMI configuration for disabling credit flow to firmware
by two ways.
1. By using a global flag
(HTC_MSG_SETUP_COMPLETE_EX_ID msg type flags)
2. By using a local flag
(ATH11K_HTC_CONN_FLAGS_DISABLE_CREDIT_FLOW_CTRL = 1 << 3)

Ath11k uses both these configurations to disable credit flow for the
WMI path completely.

Also added a hw_param member for credit flow control by which we can
enable or disable it based on per-target basis. Currently we are disabling
credit flow for IPQ8074, IPQ6018, and QCN9074 as recommended by firmware.

Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01492-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ6018 hw1.0 AHB WLAN.HK.2.4.0.1-00330-QCAHKSWPL_SILICONZ-1

Co-developed-by: Pravas Kumar Panda <kumarpan@codeaurora.org>
Signed-off-by: Pravas Kumar Panda <kumarpan@codeaurora.org>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1635156494-20059-1-git-send-email-quic_ppranees@quicinc.com

ath11k: Fix ETSI regd with weather radar overlap

Some ETSI countries have a small overlap in the wireless-regdb with an ETSI
channel (5590-5650). A good example is Australia:

  country AU: DFS-ETSI
   (2400 - 2483.5 @ 40), (36)
   (5150 - 5250 @ 80), (23), NO-OUTDOOR, AUTO-BW
   (5250 - 5350 @ 80), (20), NO-OUTDOOR, AUTO-BW, DFS
   (5470 - 5600 @ 80), (27), DFS
   (5650 - 5730 @ 80), (27), DFS
   (5730 - 5850 @ 80), (36)
   (57000 - 66000 @ 2160), (43), NO-OUTDOOR

If the firmware (or the BDF) is shipped with these rules then there is only
a 10 MHz overlap with the weather radar:

* below: 5470 - 5590
* weather radar: 5590 - 5600
* above: (none for the rule "5470 - 5600 @ 80")

There are several wrong assumption in the ath11k code:

* there is always a valid range below the weather radar
  (actually: there could be no range below the weather radar range OR range
   could be smaller than 20 MHz)
* intersected range in the weather radar range is valid
  (actually: the range could be smaller than 20 MHz)
* range above weather radar is either empty or valid
  (actually: the range could be smaller than 20 MHz)

These wrong assumption will lead in this example to a rule

  (5590 - 5600 @ 20), (N/A, 27), (600000 ms), DFS, AUTO-BW

which is invalid according to is_valid_reg_rule() because the freq_diff is
only 10 MHz but the max_bandwidth is set to 20 MHz. Which results in a
rejection like:

  WARNING: at backports-20210222_001-4.4.60-b157d2276/net/wireless/reg.c:3984
  [...]
  Call trace:
  [<ffffffbffc3d2e50>] reg_get_max_bandwidth+0x300/0x3a8 [cfg80211]
  [<ffffffbffc3d3d0c>] regulatory_set_wiphy_regd_sync+0x3c/0x98 [cfg80211]
  [<ffffffbffc651598>] ath11k_regd_update+0x1a8/0x210 [ath11k]
  [<ffffffbffc652108>] ath11k_regd_update_work+0x18/0x20 [ath11k]
  [<ffffffc0000a93e0>] process_one_work+0x1f8/0x340
  [<ffffffc0000a9784>] worker_thread+0x25c/0x448
  [<ffffffc0000aedc8>] kthread+0xd0/0xd8
  [<ffffffc000085550>] ret_from_fork+0x10/0x40
  ath11k c000000.wifi: failed to perform regd update : -22
  Invalid regulatory domain detected

To avoid this, the algorithm has to be changed slightly. Instead of
splitting a rule which overlaps with the weather radar range into 3 pieces
and accepting the first two parts blindly, it must actually be checked for
each piece whether it is a valid range. And only if it is valid, add it to
the output array.

When these checks are in place, the processed rules for AU would end up as

  country AU: DFS-ETSI
          (2400 - 2483 @ 40), (N/A, 36), (N/A)
          (5150 - 5250 @ 80), (6, 23), (N/A), NO-OUTDOOR, AUTO-BW
          (5250 - 5350 @ 80), (6, 20), (0 ms), NO-OUTDOOR, DFS, AUTO-BW
          (5470 - 5590 @ 80), (6, 27), (0 ms), DFS, AUTO-BW
          (5650 - 5730 @ 80), (6, 27), (0 ms), DFS, AUTO-BW
          (5730 - 5850 @ 80), (6, 36), (N/A), AUTO-BW

and will be accepted by the wireless regulatory code.

Fixes: d5c65159f289 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211112153116.1214421-1-sven@narfation.org

ath11k: Increment pending_mgmt_tx count before tx send invoke

There is a race condition whereby the tx completion handler can be invoked
before the 'num_pending_mgmt_tx" count is incremented. If that occurs, we
could get warning trace indicating that 'num_pending_mgmt_tx' is 0 (because
it was not yet incremented). Ideally, this trace should be seen only if
mgmt tx has not happened but tx completion is received, and it is not
expected in this race condition.

Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01386-QCAHKSWPL_SILICONZ-1

Co-developed-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1635168282-8845-1-git-send-email-quic_ppranees@quicinc.com

ath11k: send proper txpower and maxregpower values to firmware

Set proper values for max_regpower, max_power, max_antenna_gain as it
is because firmware will convert power values to 0.5dbm steps by
multiplying it with 2.

If txpower is not set, it will lead to cca stuck resulting in latency
issues for QCN9074.

Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01386-QCAHKSWPL_SILICONZ-1

Co-developed-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1635164229-22880-1-git-send-email-quic_ppranees@quicinc.com

ath11k: fix FCS_ERR flag in radio tap header

In radio tap header, BAD FCS flag is not updated properly because
driver failed to update FCS_ERR flag in monitor mode.

In rx_desc, FCS_ERR information is available in rx_attention
structure and presence of this field indicates corresponding frame
failed FCS check.

Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1

Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1635164060-18423-1-git-send-email-quic_ppranees@quicinc.com

ath11k: move peer delete after vdev stop of station for QCA6390 and WCN6855

When station connect to AP, the wmi command sequence is:

peer_create->vdev_start->vdev_up

and sequence of station disconnect fo AP is:

peer_delete->vdev_down->vdev_stop

The sequence of disconnect is not opposite of connect, it caused firmware
crash when it handle wmi vdev stop cmd when the AP is support TWT of
802.11 ax, because firmware need access the bss peer for vdev stop cmd.

[  390.438564] ath11k_pci 0000:05:00.0: wmi cmd send 0x6001 ret 0
[  390.438567] ath11k_pci 0000:05:00.0: WMI peer create vdev_id 0 peer_addr c4:04:15:3b:e0:39
[  390.472724] ath11k_pci 0000:05:00.0: mac vdev 0 start center_freq 2437 phymode 11ax-he20-2g
[  390.472731] ath11k_pci 0000:05:00.0: wmi cmd send 0x5003 ret 0
[  390.560849] ath11k_pci 0000:05:00.0: wmi cmd send 0x5005 ret 0
[  390.560850] ath11k_pci 0000:05:00.0: WMI mgmt vdev up id 0x0 assoc id 1 bssid c4:04:15:3b:e0:39

[  399.432896] ath11k_pci 0000:05:00.0: WMI peer delete vdev_id 0 peer_addr c4:04:15:3b:e0:39
[  399.432902] ath11k_pci 0000:05:00.0: wmi cmd send 0x6002 ret 0
[  399.441380] ath11k_pci 0000:05:00.0: wmi cmd send 0x5007 ret 0
[  399.441381] ath11k_pci 0000:05:00.0: WMI vdev down id 0x0
[  399.454681] ath11k_pci 0000:05:00.0: wmi cmd send 0x5006 ret 0
[  399.454682] ath11k_pci 0000:05:00.0: WMI vdev stop id 0x0

The opposite sequence of disconnect should be:

vdev_down->vdev_stop->peer_delete

This patch change the sequence of disconnect for station as above
opposite sequence for QCA6390, firmware not crash again with this patch.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1

Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211027093825.12167-1-quic_wgong@quicinc.com

ath11k: fix the value of msecs_to_jiffies in ath11k_debugfs_fw_stats_request

parameter of msecs_to_jiffies should be (3 * 1000) instead of (3 * HZ)

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1

Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211026032014.27010-1-quic_wgong@quicinc.com

ath11k: remove return for empty tx bitrate in mac_op_sta_statistics

Currently in ath11k_mac_op_sta_statistics() there is the following
logic:

if (!arsta->txrate.legacy && !arsta->txrate.nss)
return;

Unfortunately if this condition is true then the function returns without
setting parameters that follow the txrate. To address this issue remove the
return and instead invert the logic to set the txrate logic if
(arsta->txrate.legacy || arsta->txrate.nss).

The same was done also in ath10k in commit 1cd6ba8ae33e ("ath10k: remove return
for NL80211_STA_INFO_TX_BITRATE").

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1

Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211011084957.31024-1-wgong@codeaurora.org

ath11k: enable IEEE80211_VHT_EXT_NSS_BW_CAPABLE if NSS ratio enabled

When NSS ratio enabled reported by firmware, SUPPORTS_VHT_EXT_NSS_BW
is set in ath11k, meanwhile IEEE80211_VHT_EXT_NSS_BW_CAPABLE also
need to be set, otherwise it is invalid because spec in IEEE Std
802.11™‐2020 as below.

Table 9-273-Supported VHT-MCS and NSS Set subfields, it has subfield
VHT Extended NSS BW Capable, its definition is:
Indicates whether the STA is capable of interpreting the Extended NSS
BW Support subfield of the VHT Capabilities Information field.

dmesg have a message without this patch:

ieee80211 phy0: copying sband (band 1) due to VHT EXT NSS BW flag

It means mac80211 will set IEEE80211_VHT_EXT_NSS_BW_CAPABLE if ath11k not
set it in ieee80211_register_hw(). So it is better to set it in ath11k.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1

Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211013073704.15888-1-wgong@codeaurora.org

ath11k: avoid unnecessary lock contention in tx_completion path

Avoid unnecessary idr_find calls before the idr_remove calls. Because
idr_remove gives the valid ptr if id is valid otherwise return NULL ptr.
So removed the idr_find before idr_remove in tx completion path. Also no
need to disable the bottom half preempt if it is already in the
bottom half context, so modify the spin_lock_bh to spin_lock in the
data tx completion path.

Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1 v2

Co-developed-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-13-git-send-email-ppranees@codeaurora.org

ath11k: add branch predictors in dp_tx path

Add branch prediction in dp_tx code path in tx and tx completion handlers.
Also in ath11k_dp_tx_complete_msdu , the pointer that is returned by
rcu_dereference() is not dereferenced. so it is preferable to use
rcu_access_pointer() here.

Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1 v2

Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-12-git-send-email-ppranees@codeaurora.org

ath11k: avoid while loop in ring selection of tx completion interrupt

Currently while loop is used to find the tx completion ring number and
it is not required since the tx ring mask and the group id can be combined
to directly fetch the ring number. Hence remove the while loop
and directly get the ring number from tx mask and group id.

Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1 v2

Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-11-git-send-email-ppranees@codeaurora.org

ath11k: remove mod operator in dst ring processing

Replace use of mod operator with a manual wrap around
to avoid additional cost of using mod operation.

Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1 v2

Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-10-git-send-email-ppranees@codeaurora.org

ath11k: allocate HAL_WBM2SW_RELEASE ring from cacheable memory

Similar to REO destination ring, also allocate HAL_WBM2SW_RELEASE
from cacheable memory so that descriptors could be prefetched during
tx completion handling.

Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1 v2

Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-9-git-send-email-ppranees@codeaurora.org

ath11k: add branch predictors in process_rx

In datapath, add branch predictors where required in the process rx().
This protects high value rx path without having performance overhead.
Also while processing rx packets, the pointer that is returned by
rcu_dereference() is not dereferenced. so it is preferable to use
rcu_access_pointer() here.

Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1

Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-8-git-send-email-ppranees@codeaurora.org

ath11k: remove usage quota while processing rx packets

The usage of quota variable inside ath11k_dp_rx_process_received_packets()
is redundant. Since we would queue only max packets to the list before
calling this function so it would never exceed quota. Hence removing
usage of quota variable.

Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1

Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-7-git-send-email-ppranees@codeaurora.org

ath11k: avoid active pdev check for each msdu

The Active Pdev and CAC check are done for each msdu in
ath11k_dp_rx_process_received_packets which is a overhead.
To avoid this overhead, collect all msdus in a per mac msdu
list and pass to function.

Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1

Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-6-git-send-email-ppranees@codeaurora.org

ath11k: avoid additional access to ath11k_hal_srng_dst_num_free

In ath11k_dp_process_rx(), after processing rx_desc from
ath11k_hal_srng_dst_get_next_entry(), ath11k_hal_srng_dst_num_free()
is accessed everytime because of done flag is not set.

To avoid this additional access to ath11k_hal_srng_dst_num_free(),
increment total_msdu_reaped only when continuation is not set and
update done flag correspondingly.

Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1

Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-5-git-send-email-ppranees@codeaurora.org

ath11k: modify dp_rx desc access wrapper calls inline

In data path, to reduce the CPU cycles spending on descriptor access
wrapper function, changed those functions as static inline.

Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1

Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-4-git-send-email-ppranees@codeaurora.org

ath11k: allocate dst ring descriptors from cacheable memory

tcl_data and reo_dst rings are currently being allocated using
dma_allocate_coherent() which is non cacheable.

Allocating ring memory from cacheable memory area allows cached descriptor
access and prefetch next descriptors to optimize CPU usage during
descriptor processing on NAPI. Based on the hardware param we can enable
or disable this feature for the corresponding platform.

Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1

Co-developed-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-3-git-send-email-ppranees@codeaurora.org

ath11k: disable unused CE8 interrupts for ipq8074

Host driver doesn't need to process CE8 interrupts (used
by target independently)

The volume of interrupts is huge within short interval,
CPU0 CPU1 CPU2 CPU3
14022188 0 0 0 GIC 71 Edge ce8

Hence disabling unused CE8 interrupt will improve CPU usage.

Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1

Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-2-git-send-email-ppranees@codeaurora.org

ath11k: fix firmware crash during channel switch

Currently the updated bandwidth for the peer will be configured
to the firmware after channel switch from the sta_rc_update_wk.
If the updated bandwidth is greater than the configured peer phymode
during the peer assoc may result firmware assert.

For example, initially AP is in HE40 mode and the peer phymode is
configured as MODE_11AX_HE40 during peer assoc. Now user change the
channel width to HE80 then, the peer bandwidth will be updated as
HE80 to the firmware.

This will trigger firmware assert due to peer bandwidth is greater than
the peer phymode.

Fix this issue by sending peer assoc command before setting the updated
peer bandwith to firmware.

Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1

Signed-off-by: Venkateswara Naralasetty <quic_vnaralas@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1636644002-25446-1-git-send-email-quic_vnaralas@quicinc.com

ath11k: Fix 'unused-but-set-parameter' error

Below compilation error is reported when built with W=1,

drivers/net/wireless/ath/ath11k/mac.c:5408:22: error: parameter 'changed_flags' set but not used [-Werror,-Wunused-but-set-parameter]

changed_flags is set, but left unused. So, remove unnecessary set.
Compile tested only.

Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Seevalamuthu Mariappan <quic_seevalam@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1636609967-5114-1-git-send-email-quic_seevalam@quicinc.com

ath11k: fix DMA memory free in CE pipe cleanup

In CE pipe cleanup, DMA memory gets freed by the aligned address
(base_addr_owner_space) which is wrong. It needs to be freed
by the address (base_addr_owner_space_unaligned) returned by
dma_alloc. So free the dma memory by the proper address.
This was found in code review.

Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-00729-QCAHKSWPL_SILICONZ-3 v2

Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1636561290-18966-1-git-send-email-quic_periyasa@quicinc.com

ath11k: avoid unnecessary BH disable lock in STA kickout event

In STA kickout event processing, the peer object is protected
under spin lock BH. Release this lock after picking up the vdev_id
from the peer object instead after ieee80211_report_low_ack().
This will minimize the lock hold period which will improve
performance since base_lock is used across the data path.
This was found in code review.

Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-00729-QCAHKSWPL_SILICONZ-3 v2

Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1636560388-24955-1-git-send-email-quic_periyasa@quicinc.com

ath11k: fix error routine when fallback of add interface fails

When there is an error in add interface process from
ath11k_mac_set_kickout(), the code attempts to handle a
fallback for add_interface. When this fallback succeeds, the
driver returns zero rather than error code. This leads to
success for the non created VAP. In cleanup, driver gets
remove interface callback for the non created VAP and
proceeds to self peer delete request which leads to FW assert.
Since it was already deleted on the fallback of add interface,
return the actual error code instead of fallback return code.

Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-00729-QCAHKSWPL_SILICONZ-3 v2

Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1636558557-2874-1-git-send-email-quic_periyasa@quicinc.com

ath11k: fix fw crash due to peer get authorized before key install

Firmware expects host to authorize the peer after the successful key
install. But host authorize the peer before the key install, this trigger
the firmware assert which leads to Q6 crash. To avoid this Q6 crash, host
should authorize the peer after the key install. So introduce is_authorized
in peer object to identify that peer is authorize or not. When
IEEE80211_STA_CONTROL_PORT flag is unset, peer move to authorize state
before the vdev up. When the same flag is set then peer move to authorize
state after vdev up. So added authorise check in ath11k_bss_assoc() to
handle the earlier state transition case. Also added the WMI authorize
procedure in ath11k_mac_op_sta_state() to handle the non-earlier state
transition case.

Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01492-QCAHKSWPL_SILICONZ-1

Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1636554200-12345-1-git-send-email-quic_periyasa@quicinc.com

ath11k: Clear auth flag only for actual association in security mode

AUTH flag is needed when peer assoc command is sent from host in
security mode for non-assoc cases. Firmware will handle AUTH flag
when client is associating as AUTH flag will be set after key exchange.
For internally provided peer assoc commands from host, there won't be
any key exchange, so AUTH flag is expected to be set in host.

Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01838-QCAHKSWPL_SILICONZ-1

Co-developed-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: Lavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1635177786-20854-1-git-send-email-quic_ramess@quicinc.com

ath11k: Send PPDU_STATS_CFG with proper pdev mask to firmware

HTT_PPDU_STATS_CFG_PDEV_ID bit mask for target FW PPDU stats request message
was set as bit 8 to 15. Bit 8 is reserved for soc stats and pdev id starts from
bit 9. Hence change the bitmask as bit 9 to 15 and fill the proper pdev id in
the request message.

In commit 701e48a43e15 ("ath11k: add packet log support for QCA6390"), both
HTT_PPDU_STATS_CFG_PDEV_ID and pdev_mask were changed, but this pdev_mask
calculation is not valid for platforms which has multiple pdevs with 1 rxdma
per pdev, as this is writing same value(i.e. 2) for all pdevs. Hence fixed it
to consider pdev_idx as well, to make it compatible for both single and multi
pd cases.

Tested on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01092-QCAHKSWPL_SILICONZ-1
Tested on: IPQ6018 hw1.0 WLAN.HK.2.5.0.1-01067-QCAHKSWPL_SILICONZ-1

Fixes: 701e48a43e15 ("ath11k: add packet log support for QCA6390")

Co-developed-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Rameshkumar Sundaram <ramess@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721212029.142388-10-jouni@codeaurora.org

ar5523: Fix null-ptr-deref with unexpected WDCMSG_TARGET_START reply

Unexpected WDCMSG_TARGET_START replay can lead to null-ptr-deref
when ar->tx_cmd->odata is NULL. The patch adds a null check to
prevent such case.

KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
ar5523_cmd+0x46a/0x581 [ar5523]
ar5523_probe.cold+0x1b7/0x18da [ar5523]
? ar5523_cmd_rx_cb+0x7a0/0x7a0 [ar5523]
? __pm_runtime_set_status+0x54a/0x8f0
? _raw_spin_trylock_bh+0x120/0x120
? pm_runtime_barrier+0x220/0x220
? __pm_runtime_resume+0xb1/0xf0
usb_probe_interface+0x25b/0x710
really_probe+0x209/0x5d0
driver_probe_device+0xc6/0x1b0
device_driver_attach+0xe2/0x120

I found the bug using a custome USBFuzz port. It's a research work
to fuzz USB stack/drivers. I modified it to fuzz ath9k driver only,
providing hand-crafted usb descriptors to QEMU.

After fixing the code (fourth byte in usb packet) to WDCMSG_TARGET_START,
I got the null-ptr-deref bug. I believe the bug is triggerable whenever
cmd->odata is NULL. After patching, I tested with the same input and no
longer see the KASAN report.

This was NOT tested on a real device.

Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/YXsmPQ3awHFLuAj2@10-18-43-117.dynapool.wireless.nyu.edu

ath11k: enable 802.11 power save mode in station mode

To reduce power consumption enable 802.11 power save mode in station mode. This
allows both radio and CPU to sleep more.

Only enable the mode on QCA6390 and WCN6855, it's unknown how other hardware
families support this feature.

To test that power save mode is running run "iw dev wls1 set power_save off",
check there is no NULL Data frame seen by a sniffer. And run "iw dev wls1 set power_save
on" and check there is a NULL Data frame in sniffer.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1

Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211108123826.8463-2-kvalo@codeaurora.org

ath11k: convert ath11k_wmi_pdev_set_ps_mode() to use enum wmi_sta_ps_mode

It's more descriptive to use the actual enum used by the firmware instead of a
boolean so change ath11k_wmi_pdev_set_ps_mode() to use a boolean.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1

Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211108123826.8463-1-kvalo@codeaurora.org

wcn36xx: fix RX BD rate mapping for 5GHz legacy rates

The linear mapping between the BD rate field and the driver's 5GHz
legacy rates table (wcn_5ghz_rates) does not only apply for the latter
four rates -- it applies to all eight rates.

Fixes: 6ea131acea98 ("wcn36xx: Fix warning due to bad rate_idx")
Signed-off-by: Benjamin Li <benl@squareup.com>
Tested-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211104010548.1107405-3-benl@squareup.com

wcn36xx: populate band before determining rate on RX

status.band is used in determination of status.rate -- for 5GHz on legacy
rates there is a linear shift between the BD descriptor's rate field and
the wcn36xx driver's rate table (wcn_5ghz_rates).

We have a special clause to populate status.band for hardware scan offload
frames. However, this block occurs after status.rate is already populated.
Correctly handle this dependency by moving the band block before the rate
block.

This patch addresses kernel warnings & missing scan results for 5GHz APs
that send their beacons/probe responses at the higher four legacy rates
(24-54 Mbps), when using hardware scan offload:

  ------------[ cut here ]------------
  WARNING: CPU: 0 PID: 0 at net/mac80211/rx.c:4532 ieee80211_rx_napi+0x744/0x8d8
  Modules linked in: wcn36xx [...]
  CPU: 0 PID: 0 Comm: swapper/0 Tainted: G        W         4.19.107-g73909fa #1
  Hardware name: Square, Inc. T2 (all variants) (DT)
  Call trace:
  dump_backtrace+0x0/0x148
  show_stack+0x14/0x1c
  dump_stack+0xb8/0xf0
  __warn+0x2ac/0x2d8
  warn_slowpath_null+0x44/0x54
  ieee80211_rx_napi+0x744/0x8d8
  ieee80211_tasklet_handler+0xa4/0xe0
  tasklet_action_common+0xe0/0x118
  tasklet_action+0x20/0x28
  __do_softirq+0x108/0x1ec
  irq_exit+0xd4/0xd8
  __handle_domain_irq+0x84/0xbc
  gic_handle_irq+0x4c/0xb8
  el1_irq+0xe8/0x190
  lpm_cpuidle_enter+0x220/0x260
  cpuidle_enter_state+0x114/0x1c0
  cpuidle_enter+0x34/0x48
  do_idle+0x150/0x268
  cpu_startup_entry+0x20/0x24
  rest_init+0xd4/0xe0
  start_kernel+0x398/0x430
  ---[ end trace ae28cb759352b403 ]---

Fixes: 8a27ca394782 ("wcn36xx: Correct band/freq reporting on RX")
Signed-off-by: Benjamin Li <benl@squareup.com>
Tested-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211104010548.1107405-2-benl@squareup.com

wcn36xx: Put DXE block into reset before freeing memory

When deiniting the DXE hardware we should reset the block to ensure there
is no spurious DMA write transaction from the downstream WCNSS to upstream
MSM at a skbuff address we will have released.

Fixes: 8e84c2582169 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211105122152.1580542-4-bryan.odonoghue@linaro.org

wcn36xx: Release DMA channel descriptor allocations

When unloading the driver we are not releasing the DMA descriptors which we
previously allocated.

Fixes: 8e84c2582169 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211105122152.1580542-3-bryan.odonoghue@linaro.org

wcn36xx: Fix DMA channel enable/disable cycle

Right now we have a broken sequence where we enable DMA channel interrupts
which can be left enabled and never disabled if we hit an error path.

Worse still when we unload the driver, the DMA channel interrupt bits are
left intact. About the only saving grace here is that we do remember to
disable the wcnss interrupt when unload the driver.

Fixes: 8e84c2582169 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211105122152.1580542-2-bryan.odonoghue@linaro.org

ath9k: use swap() to make code cleaner

Using swap() make it more readable.

Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Yang Guang <yang.guang5@zte.com.cn>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211028010451.7754-1-yang.guang5@zte.com.cn

wcn36xx: Indicate beacon not connection loss on MISSED_BEACON_IND

Firmware can trigger a missed beacon indication, this is not the same as a
lost signal.

Flag to Linux the missed beacon and let the WiFi stack decide for itself if
the link is up or down by sending its own probe to determine this.

We should only be signalling the link is lost when the firmware indicates

Fixes: 8e84c2582169 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211027232529.657764-1-bryan.odonoghue@linaro.org

wcn36xx: ensure pairing of init_scan/finish_scan and start_scan/end_scan

An SMD capture from the downstream prima driver on WCN3680B shows the
following command sequence for connected scans:

- init_scan_req
    - start_scan_req, channel 1
    - end_scan_req, channel 1
    - start_scan_req, channel 2
    - ...
    - end_scan_req, channel 3
- finish_scan_req
- init_scan_req
    - start_scan_req, channel 4
    - ...
    - end_scan_req, channel 6
- finish_scan_req
- ...
    - end_scan_req, channel 165
- finish_scan_req

Upstream currently never calls wcn36xx_smd_end_scan, and in some cases[1]
still sends finish_scan_req twice in a row or before init_scan_req. A
typical connected scan looks like this:

- init_scan_req
    - start_scan_req, channel 1
- finish_scan_req
- init_scan_req
    - start_scan_req, channel 2
- ...
    - start_scan_req, channel 165
- finish_scan_req
- finish_scan_req

This patch cleans up scanning so that init/finish and start/end are always
paired together and correctly nested.

- init_scan_req
    - start_scan_req, channel 1
    - end_scan_req, channel 1
- finish_scan_req
- init_scan_req
    - start_scan_req, channel 2
    - end_scan_req, channel 2
- ...
    - start_scan_req, channel 165
    - end_scan_req, channel 165
- finish_scan_req

Note that upstream will not do batching of 3 active-probe scans before
returning to the operating channel, and this patch does not change that.
To match downstream in this aspect, adjust IEEE80211_PROBE_DELAY and/or
the 125ms max off-channel time in ieee80211_scan_state_decision.

[1]: commit d195d7aac09b ("wcn36xx: Ensure finish scan is not requested
before start scan") addressed one case of finish_scan_req being sent
without a preceding init_scan_req (the case of the operating channel
coinciding with the first scan channel); two other cases are:
1) if SW scan is started and aborted immediately, without scanning any
   channels, we send a finish_scan_req without ever sending init_scan_req,
   and
2) as SW scan logic always returns us to the operating channel before
   calling wcn36xx_sw_scan_complete, finish_scan_req is always sent twice
   at the end of a SW scan

Fixes: 8e84c2582169 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware")
Signed-off-by: Benjamin Li <benl@squareup.com>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211027170306.555535-4-benl@squareup.com

wcn36xx: implement flush op to speed up connected scan

Without ieee80211_ops->flush implemented to empty HW queues, mac80211 will
do a 100ms dead wait after stopping SW queues, before leaving the operating
channel to resume a software connected scan[1].
(see ieee80211_scan_state_resume)

This wait is correctly included in the calculation for whether or not
we've exceeded max off-channel time, as it occurs after sending the null
frame with PS bit set. Thus, with 125 ms max off-channel time we only
have 25 ms of scan time, which technically isn't even enough to scan one
channel (although mac80211 always scans at least one channel per off-
channel window).

Moreover, for passive probes we end up spending at least 100 ms + 111 ms
(IEEE80211_PASSIVE_CHANNEL_TIME) "off-channel"[2], which exceeds the listen
interval of 200 ms that we provide in our association request frame. That's
technically out-of-spec.

[1]: Until recently, wcn36xx performed software (rather than FW-offloaded)
scanning when 5GHz channels are requested. This apparent limitation is now
resolved -- see commit 1395f8a6a4d5 ("wcn36xx: Enable hardware scan offload
for 5Ghz band").
[2]: in quotes because about 100 ms of it is still on-channel but with PS
set

Signed-off-by: Benjamin Li <benl@squareup.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211027170306.555535-3-benl@squareup.com

wcn36xx: add debug prints for sw_scan start/complete

Add some MAC debug prints for more easily demarcating a software scan
when parsing logs.

Signed-off-by: Benjamin Li <benl@squareup.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211027170306.555535-2-benl@squareup.com

ath10k: fetch (pre-)calibration data via nvmem subsystem

ATH10K chips are used it wide range of routers,
accesspoints, range extenders, network appliances.
On these embedded devices, calibration data is often
stored on the main system's flash and was out of reach
for the driver.

To bridge this gap, ath10k is getting extended to pull
the (pre-)calibration data through nvmem subsystem.
To do this, a nvmem-cell containing the information can
either be specified in the platform data or via device-tree.

Tested with:
Netgear EX6150v2 (IPQ4018 - pre-calibration method)
TP-Link Archer C7 v2 (QCA9880v2 - old calibration method)

Cc: Robert Marko <robimarko@gmail.com>
Cc: Thibaut VARÈNE <hacks@slashdirt.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211016234609.1568317-1-chunkeey@gmail.com

ath11k: set correct NL80211_FEATURE_DYNAMIC_SMPS for WCN6855

Commit 6f4d70308e5e ("ath11k: support SMPS configuration for 6 GHz") changed
"if (ht_cap & WMI_HT_CAP_DYNAMIC_SMPS)" to "if (ht_cap &
WMI_HT_CAP_DYNAMIC_SMPS || ar->supports_6ghz)" which means
NL80211_FEATURE_DYNAMIC_SMPS is enabled for all chips which support 6 GHz.
However, WCN6855 supports 6 GHz but it does not support feature
NL80211_FEATURE_DYNAMIC_SMPS, and this can lead to MU-MIMO test failures for
WCN6855.

Disable NL80211_FEATURE_DYNAMIC_SMPS for WCN6855 since its ht_cap does not
support WMI_HT_CAP_DYNAMIC_SMPS. Enable the feature only on QCN9074 as that's
the only other device supporting 6 GHz band.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1

Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914163726.38604-3-jouni@codeaurora.org

ath6kl: fix division by zero in send path

Add the missing endpoint max-packet sanity check to probe() to avoid
division by zero in ath10k_usb_hif_tx_sg() in case a malicious device
has broken descriptors (or when doing descriptor fuzz testing).

Note that USB core will reject URBs submitted for endpoints with zero
wMaxPacketSize but that drivers doing packet-size calculations still
need to handle this (cf. commit 2548288b4fb0 ("USB: Fix: Don't skip
endpoint descriptors with maxpacket=0")).

Fixes: 9cbee358687e ("ath6kl: add full USB support")
Cc: stable@vger.kernel.org # 3.5
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211027080819.6675-3-johan@kernel.org

ath10k: fix division by zero in send path

Add the missing endpoint max-packet sanity check to probe() to avoid
division by zero in ath10k_usb_hif_tx_sg() in case a malicious device
has broken descriptors (or when doing descriptor fuzz testing).

Note that USB core will reject URBs submitted for endpoints with zero
wMaxPacketSize but that drivers doing packet-size calculations still
need to handle this (cf. commit 2548288b4fb0 ("USB: Fix: Don't skip
endpoint descriptors with maxpacket=0")).

Fixes: 4db66499df91 ("ath10k: add initial USB support")
Cc: stable@vger.kernel.org # 4.14
Cc: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211027080819.6675-2-johan@kernel.org

ath6kl: fix control-message timeout

USB control-message timeouts are specified in milliseconds and should
specifically not vary with CONFIG_HZ.

Fixes: 241b128b6b69 ("ath6kl: add back beginnings of USB support")
Cc: stable@vger.kernel.org # 3.4
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211025120522.6045-3-johan@kernel.org

ath10k: fix control-message timeout

USB control-message timeouts are specified in milliseconds and should
specifically not vary with CONFIG_HZ.

Fixes: 4db66499df91 ("ath10k: add initial USB support")
Cc: stable@vger.kernel.org # 4.14
Cc: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211025120522.6045-2-johan@kernel.org

wcn36xx: add missing 5GHz channels 136 and 144

The official feature-complete WCN3680B driver (known as prima, open source
but not upstream) supports channels 136 and 144.

However, these channels are missing in upstream. Add them here to get
closer to feature parity with prima.

Signed-off-by: Benjamin Li <benl@squareup.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211025175359.3591048-3-benl@squareup.com

wcn36xx: switch on antenna diversity feature bit

The official feature-complete WCN3680B driver (known as prima, open source
but not upstream) sends this feature bit.

As we wish to support the antenna diversity feature in upstream, we need
to set this bit as well.

Signed-off-by: Benjamin Li <benl@squareup.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211025175359.3591048-2-benl@squareup.com

wcn36xx: Channel list update before hardware scan

The channel scan list must be updated before triggering a hardware scan
so that firmware takes into account the regulatory info for each single
channel such as active/passive config, power, DFS, etc... Without this
the firmware uses its own internal default channel configuration, which
is not aligned with mac80211 regulatory rules, and misses several
channels (e.g. 144).

Fixes: 2f3bef4b247e ("wcn36xx: Add hardware scan offload support")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1635175328-25642-1-git-send-email-loic.poulain@linaro.org

Revert "wcn36xx: Enable firmware link monitoring"

Firmware link offload monitoring can be made to work in 3/4 cases by
switching on firmware feature bit WLANACTIVE_OFFLOAD

- Secure power-save on
- Secure power-save off
- Open power-save on

However, with an open AP if we switch off power-saving - thus never
entering Beacon Mode Power Save - BMPS, firmware never forwards loss
of beacon upwards.

We had hoped that WLANACTIVE_OFFLOAD and some fixes for sequence numbers
would unblock this but, it hasn't and further investigation is required.

Its possible to have a complete set of Secure power-save on/off and Open
power-save on/off provided we use Linux' link monitoring mechanism.

While we debug the Open AP failure we need to fix upstream.

This reverts commit c973fdad79f6eaf247d48b5fc77733e989eb01e1.

Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211025093037.3966022-2-bryan.odonoghue@linaro.org

wcn36xx: Fix packet drop on resume

If the system is resumed because of an incoming packet, the wcn36xx RX
interrupts is fired before actual resuming of the wireless/mac80211
stack, causing any received packets to be simply dropped. E.g. a ping
request causes a system resume, but is dropped and so never forwarded
to the IP stack.

This change fixes that, disabling DMA interrupts on suspend to no pass
packets until mac80211 is resumed and ready to handle them.

Note that it's not incompatible with RX irq wake.

Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1635150496-19290-1-git-send-email-loic.poulain@linaro.org

wcn36xx: Fix discarded frames due to wrong sequence number

The firmware is offering features such as ARP offload, for which
firmware crafts its own (QoS)packets without waking up the host.
Point is that the sequence numbers generated by the firmware are
not in sync with the host mac80211 layer and can cause packets
such as firmware ARP reponses to be dropped by the AP (too old SN).

To fix this we need to let the firmware manages the sequence
numbers by its own (except for QoS null frames). There is a SN
counter for each QoS queue and one global/baseline counter for
Non-QoS.

Fixes: 84aff52e4f57 ("wcn36xx: Use sequence number allocated by mac80211")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1635150336-18736-1-git-send-email-loic.poulain@linaro.org

wcn36xx: add proper DMA memory barriers in rx path

This is essentially exactly following the dma_wmb()/dma_rmb() usage
instructions in Documentation/memory-barriers.txt.

The theoretical races here are:

1. DXE (the DMA Transfer Engine in the Wi-Fi subsystem) seeing the
dxe->ctrl & WCN36xx_DXE_CTRL_VLD write before the dxe->dst_addr_l
write, thus performing DMA into the wrong address.

2. CPU reading dxe->dst_addr_l before DXE unsets dxe->ctrl &
WCN36xx_DXE_CTRL_VLD. This should generally be harmless since DXE
doesn't write dxe->dst_addr_l (no risk of freeing the wrong skb).

Fixes: 8e84c2582169 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware")
Signed-off-by: Benjamin Li <benl@squareup.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211023001528.3077822-1-benl@squareup.com

wcn36xx: Fix HT40 capability for 2Ghz band

All wcn36xx controllers are supposed to support HT40 (and SGI40),
This doubles the maximum bitrate/throughput with compatible APs.

Tested with wcn3620 & wcn3680B.

Cc: stable@vger.kernel.org
Fixes: 8e84c2582169 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1634737133-22336-1-git-send-email-loic.poulain@linaro.org

Revert "wcn36xx: Disable bmps when encryption is disabled"

This reverts commit c6522a5076e1a65877c51cfee313a74ef61cabf8.

Testing on tip-of-tree shows that this is working now. Revert this and
re-enable BMPS for Open APs.

Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211022140447.2846248-3-bryan.odonoghue@linaro.org

wcn36xx: Treat repeated BMPS entry fail as connection loss

On an open AP when you pull the plug on the AP, if we are not already in
BMPS mode then the firmware will not generate a disconnection event.

Instead we need to monitor for failure to enter BMPS and treat a string of
failures as connection loss.

Secure AP connections don't appear to demonstrate this behavior so the
work-around is limited to open APs only.

Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211022140447.2846248-2-bryan.odonoghue@linaro.org

wcn36xx: Add chained transfer support for AMSDU

WCNSS RX DMA transfer support is limited to 3872 bytes, which is
enough for simple MPDUs (single MSDU), but not enough for cases
with A-MSDU (depending on max AMSDU size or max MPDU size).

In that case the MPDU is spread over multiple transfers, with the
first transfer containing the MPDU header and (at least) the first
A-MSDU subframe and additional transfer(s) containing the following
A-MSDUs. This can be handled with a series of flags to tagging the
first and last A-MSDU transfers.

In that case we have to bufferize and re-linearize the A-MSDU buffers
into a proper MPDU skb before forwarding to mac80211 (in the same way
as it is done in ath10k).

This change also includes sanity check of the buffer descriptor to
prevent skb overflow.

Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1634557705-11120-1-git-send-email-loic.poulain@linaro.org

wcn36xx: Enable hardware scan offload for 5Ghz band

Until now, offload scanning for 5Ghz channels was considered broken.
However it was mostly a driver issue, caused by bad reporting of the
beacons/probe-resp bands and frequencies, which has been fixed.

We can now allow offload scan for 5GHz band, this reduces the scanning
time comparing to software driven scanning.

Note that offloaded scan is limited to 48 channels, check for this.

Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1634554678-7993-2-git-send-email-loic.poulain@linaro.org

wcn36xx: Correct band/freq reporting on RX

For packets originating from hardware scan, the channel and band is
included in the buffer descriptor (bd->rf_band & bd->rx_ch).

For 2Ghz band the channel value is directly reported in the 4-bit
rx_ch field. For 5Ghz band, the rx_ch field contains a mapping
index (given the 4-bit limitation).

The reserved0 value field is also used to extend 4-bit mapping to
5-bit mapping to support more than 16 5Ghz channels.

This change adds correct reporting of the frequency/band, that is
used in scan mechanism. And is required for 5Ghz hardware scan
support.

Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1634554678-7993-1-git-send-email-loic.poulain@linaro.org

wcn36xx: Fix tx_status mechanism

This change fix the TX ack mechanism in various ways:

- For NO_ACK tagged packets, we don't need to wait for TX_ACK indication
and so are not subject to the single packet ack limitation. So we don't
have to stop the tx queue, and can call the tx status callback as soon
as DMA transfer has completed.

- Fix skb ownership/reference. Only start status indication timeout
once the DMA transfer has been completed. This avoids the skb to be
both referenced in the DMA tx ring and by the tx_ack_skb pointer,
preventing any use-after-free or double-free.

- This adds a sanity (paranoia?) check on the skb tx ack pointer.

- Resume TX queue if TX status tagged packet TX fails.

Cc: stable@vger.kernel.org
Fixes: fdf21cc37149 ("wcn36xx: Add TX ack support")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1634567281-28997-1-git-send-email-loic.poulain@linaro.org

wcn36xx: Fix (QoS) null data frame bitrate/modulation

We observe unexpected connection drops with some APs due to
non-acked mac80211 generated null data frames (keep-alive).
After debugging and capture, we noticed that null frames are
submitted at standard data bitrate and that the given APs are
in trouble with that.

After setting the null frame bitrate to control bitrate, all
null frames are acked as expected and connection is maintained.

Not sure if it's a requirement of the specification, but it seems
the right thing to do anyway, null frames are mostly used for control
purpose (power-saving, keep-alive...), and submitting them with
a slower/simpler bitrate/modulation is more robust.

Cc: stable@vger.kernel.org
Fixes: 512b191d9652 ("wcn36xx: Fix TX data path")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1634560399-15290-1-git-send-email-loic.poulain@linaro.org

ath10k: fix module load regression with iram-recovery feature

Commit 9af7c32ceca8 ("ath10k: add target IRAM recovery feature support")
introduced a new firmware feature flag ATH10K_FW_FEATURE_IRAM_RECOVERY. But
this caused ath10k_pci module load to fail if ATH10K_FW_CRASH_DUMP_RAM_DATA bit
was not enabled in the ath10k coredump_mask module parameter:

[ 2209.328190] ath10k_pci 0000:02:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe
[ 2209.434414] ath10k_pci 0000:02:00.0: kconfig debug 1 debugfs 1 tracing 1 dfs 1 testmode 1
[ 2209.547191] ath10k_pci 0000:02:00.0: firmware ver 10.4-3.9.0.2-00099 api 5 features no-p2p,mfp,peer-flow-ctrl,btcoex-param,allows-mesh-bcast,no-ps,peer-fixed-rate,iram-recovery crc32 cbade90a
[ 2210.896485] ath10k_pci 0000:02:00.0: board_file api 1 bmi_id 0:1 crc32 a040efc2
[ 2213.603339] ath10k_pci 0000:02:00.0: failed to copy target iram contents: -12
[ 2213.839027] ath10k_pci 0000:02:00.0: could not init core (-12)
[ 2213.933910] ath10k_pci 0000:02:00.0: could not probe fw (-12)

And by default coredump_mask does not have ATH10K_FW_CRASH_DUMP_RAM_DATA
enabled so anyone using a firmware with iram-recovery feature would fail. To my
knowledge only QCA9984 firmwares starting from release 10.4-3.9.0.2-00099
enabled the feature.

The reason for regression was that ath10k_core_copy_target_iram() used
ath10k_coredump_get_mem_layout() to get the memory layout, but when
ATH10K_FW_CRASH_DUMP_RAM_DATA was disabled it would get just NULL and bail out
with an error.

While looking at all this I noticed another bug: if CONFIG_DEV_COREDUMP is
disabled but the firmware has iram-recovery enabled the module load fails with
similar error messages. I fixed that by returning 0 from
ath10k_core_copy_target_iram() when _ath10k_coredump_get_mem_layout() returns
NULL.

Tested-on: QCA9984 hw2.0 PCI 10.4-3.9.0.2-00139

Fixes: 9af7c32ceca8 ("ath10k: add target IRAM recovery feature support")
Signed-off-by: Abinaya Kalaiselvan <akalaise@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211020075054.23061-1-kvalo@codeaurora.org

ath10k: fix invalid dma_addr_t token assignment

Using a kernel pointer in place of a dma_addr_t token can
lead to undefined behavior if that makes it into cache
management functions. The compiler caught one such attempt
in a cast:

drivers/net/wireless/ath/ath10k/mac.c: In function 'ath10k_add_interface':
drivers/net/wireless/ath/ath10k/mac.c:5586:47: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
5586 | arvif->beacon_paddr = (dma_addr_t)arvif->beacon_buf;
| ^

Looking through how this gets used down the way, I'm fairly
sure that beacon_paddr is never accessed again for ATH10K_DEV_TYPE_HL
devices, and if it was accessed, that would be a bug.

Change the assignment to use a known-invalid address token
instead, which avoids the warning and makes it easier to catch
bugs if it does end up getting used.

Fixes: e263bdab9c0e ("ath10k: high latency fixes for beacon buffer")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211014075153.3655910-1-arnd@kernel.org

ath11k: change return buffer manager for QCA6390

QCA6390 firmware uses HAL_RX_BUF_RBM_SW1_BM, not HAL_RX_BUF_RBM_SW3_BM. This is
needed to fix a case where an A-MSDU has an unexpected LLC/SNAP header in the
first subframe (CVE-2020-24588).

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1

Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914163726.38604-2-jouni@codeaurora.org

Merge ath-next from git://git./linux/kernel/git/kvalo/ath.git

ath.git patches for v5.16. Major changes:

ath9k

* add option to reset the wifi chip via debugfs

* convert Device Tree bindings to the json-schema

* support Device Tree ieee80211-freq-limit property to limit channels

mwifiex: Deactive host sleep using HSCFG after it was activated manually

When powersaving (so either wifi powersaving or deep sleep, depending on
which state the firmware is in) is disabled, the way the firmware goes
into host sleep is different: Usually the firmware implicitely enters
host sleep on the next SLEEP event we get when we configured host sleep
via HSCFG before. When powersaving is disabled though, there are no
SLEEP events, the way we enter host sleep in that case is different: The
firmware will send us a HS_ACT_REQ event and after that we "manually"
make the firmware enter host sleep by sending it another HSCFG command
with the action HS_ACTIVATE.

Now waking up from host sleep appears to be different depending on
whether powersaving is enabled again: When powersaving is enabled, the
firmware implicitely leaves host sleep as soon as it wakes up and sends
us an AWAKE event. When powersaving is disabled though, it apparently
doesn't implicitely leave host sleep, but instead we need to send it a
HSCFG command with the HS_CONFIGURE action and the HS_CFG_CANCEL
condition. We didn't do that so far, which is why waking up from host
sleep was broken when powersaving is disabled.

So add some additional state to mwifiex_adapter where we keep track of
whether host sleep was activated manually via HS_ACTIVATE, and if that
was the case, deactivate it manually again via HS_CFG_CANCEL.

Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211016153244.24353-6-verdre@v0yd.nl

mwifiex: Send DELBA requests according to spec

While looking at on-air packets using Wireshark, I noticed we're never
setting the initiator bit when sending DELBA requests to the AP: While
we set the bit on our del_ba_param_set bitmask, we forget to actually
copy that bitmask over to the command struct, which means we never
actually set the initiator bit.

Fix that and copy the bitmask over to the host_cmd_ds_11n_delba command
struct.

Fixes: 5e6e3a92b9a4 ("wireless: mwifiex: initial commit for Marvell mwifiex driver")
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Acked-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211016153244.24353-5-verdre@v0yd.nl

mwifiex: Fix an incorrect comment

We're sending DELBA requests here, not ADDBA requests.

Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211016153244.24353-4-verdre@v0yd.nl

mwifiex: Log an error on command failure during key-material upload

Sometimes the KEY_MATERIAL command can fail with the 88W8897 firmware
(when this happens exactly seems pretty random). This appears to prevent
the access point from starting, so it seems like a good idea to log an
error in that case.

Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211016153244.24353-3-verdre@v0yd.nl

mwifiex: Don't log error on suspend if wake-on-wlan is disabled

It's not an error if someone chooses to put their computer to sleep, not
wanting it to wake up because the person next door has just discovered
what a magic packet is. So change the loglevel of this annoying message
from ERROR to INFO.

Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211016153244.24353-2-verdre@v0yd.nl

rtw89: remove unneeded semicolon

Eliminate the following coccicheck warning:
./drivers/net/wireless/realtek/rtw89/pci.c:1348:2-3: Unneeded semicolon

Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Fixes: e3ec7017f6a2 ("rtw89: add Realtek 802.11ax driver")
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1634630094-1156-1-git-send-email-yang.lee@linux.alibaba.com

rtw89: fix return value check in rtw89_cam_send_sec_key_cmd()

Fix the return value check which testing the wrong variable
in rtw89_cam_send_sec_key_cmd().

Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: e3ec7017f6a2 ("rtw89: add Realtek 802.11ax driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211018033102.1813058-1-yangyingliang@huawei.com

mwl8k: Fix use-after-free in mwl8k_fw_state_machine()

When the driver fails to request the firmware, it calls its error
handler. In the error handler, the driver detaches device from driver
first before releasing the firmware, which can cause a use-after-free bug.

Fix this by releasing firmware first.

The following log reveals it:

[    9.007301 ] BUG: KASAN: use-after-free in mwl8k_fw_state_machine+0x320/0xba0
[    9.010143 ] Workqueue: events request_firmware_work_func
[    9.010830 ] Call Trace:
[    9.010830 ]  dump_stack_lvl+0xa8/0xd1
[    9.010830 ]  print_address_description+0x87/0x3b0
[    9.010830 ]  kasan_report+0x172/0x1c0
[    9.010830 ]  ? mutex_unlock+0xd/0x10
[    9.010830 ]  ? mwl8k_fw_state_machine+0x320/0xba0
[    9.010830 ]  ? mwl8k_fw_state_machine+0x320/0xba0
[    9.010830 ]  __asan_report_load8_noabort+0x14/0x20
[    9.010830 ]  mwl8k_fw_state_machine+0x320/0xba0
[    9.010830 ]  ? mwl8k_load_firmware+0x5f0/0x5f0
[    9.010830 ]  request_firmware_work_func+0x172/0x250
[    9.010830 ]  ? read_lock_is_recursive+0x20/0x20
[    9.010830 ]  ? process_one_work+0x7a1/0x1100
[    9.010830 ]  ? request_firmware_nowait+0x460/0x460
[    9.010830 ]  ? __this_cpu_preempt_check+0x13/0x20
[    9.010830 ]  process_one_work+0x9bb/0x1100

Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1634356979-6211-1-git-send-email-zheyuma97@gmail.com

rsi: stop thread firstly in rsi_91x_init() error handling

When fail to init coex module, free 'common' and 'adapter' directly, but
common->tx_thread which will access 'common' and 'adapter' is running at
the same time. That will trigger the UAF bug.

==================================================================
BUG: KASAN: use-after-free in rsi_tx_scheduler_thread+0x50f/0x520 [rsi_91x]
Read of size 8 at addr ffff8880076dc000 by task Tx-Thread/124777
CPU: 0 PID: 124777 Comm: Tx-Thread Not tainted 5.15.0-rc5+ #19
Call Trace:
dump_stack_lvl+0xe2/0x152
print_address_description.constprop.0+0x21/0x140
? rsi_tx_scheduler_thread+0x50f/0x520
kasan_report.cold+0x7f/0x11b
? rsi_tx_scheduler_thread+0x50f/0x520
rsi_tx_scheduler_thread+0x50f/0x520
...

Freed by task 111873:
kasan_save_stack+0x1b/0x40
kasan_set_track+0x1c/0x30
kasan_set_free_info+0x20/0x30
__kasan_slab_free+0x109/0x140
kfree+0x117/0x4c0
rsi_91x_init+0x741/0x8a0 [rsi_91x]
rsi_probe+0x9f/0x1750 [rsi_usb]

Stop thread before free 'common' and 'adapter' to fix it.

Fixes: 2108df3c4b18 ("rsi: add coex support")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211015040335.1021546-1-william.xuanziyang@huawei.com

MAINTAINERS: mt76: update MTK folks

Add more MTK folks to actively maintain the wireless chipsets across
segments. The work is becoming increasingly complicated and various
and we can provides hardware related perspectives to offload
Felix's workload, especially for the 11ax and upcoming 11be devices

Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/eb888ae0e43a980c2c1aaed372a9b5e8098ea4ef.1634107511.git.ryder.lee@mediatek.com

ath5k: replace snprintf in show functions with sysfs_emit

coccicheck complains about the use of snprintf() in sysfs show functions.

Fix the coccicheck warning:
WARNING: use scnprintf or sprintf.

Use sysfs_emit instead of scnprintf or sprintf makes more sense.

Signed-off-by: Qing Wang <wangqing@vivo.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1634095651-4273-1-git-send-email-wangqing@vivo.com

rtw89: Remove redundant check of ret after call to rtw89_mac_enable_bb_rf

The function rtw89_mac_enable_bb_rf is a void return type, so there is
no return error code to ret, so the following check for an error in ret
is redundant dead code and can be removed.

Addresses-Coverity: ("Logically dead code")
Fixes: e3ec7017f6a2 ("rtw89: add Realtek 802.11ax driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211015152113.33179-1-colin.king@canonical.com

rtw89: Fix two spelling mistakes in debug messages

There are two spelling mistakes in rtw89_debug messages. Fix them.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211015105004.11817-1-colin.king@canonical.com

MAINTAINERS: add rtw89 wireless driver

Add maintainer and email to MAINTAINERS file.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211013092827.43642-1-pkshih@realtek.com

mwifiex: Try waking the firmware until we get an interrupt

It seems that the PCIe+USB firmware (latest version 15.68.19.p21) of the
88W8897 card sometimes ignores or misses when we try to wake it up by
writing to the firmware status register. This leads to the firmware
wakeup timeout expiring and the driver resetting the card because we
assume the firmware has hung up or crashed.

Turns out that the firmware actually didn't hang up, but simply "missed"
our wakeup request and didn't send us an interrupt with an AWAKE event.

Trying again to read the firmware status register after a short timeout
usually makes the firmware wake up as expected, so add a small retry
loop to mwifiex_pm_wakeup_card() that looks at the interrupt status to
check whether the card woke up.

The number of tries and timeout lengths for this were determined
experimentally: The firmware usually takes about 500 us to wake up
after we attempt to read the status register. In some cases where the
firmware is very busy (for example while doing a bluetooth scan) it
might even miss our requests for multiple milliseconds, which is why
after 15 tries the waiting time gets increased to 10 ms. The maximum
number of tries it took to wake the firmware when testing this was
around 20, so a maximum number of 50 tries should give us plenty of
safety margin.

Here's a reproducer for those firmware wakeup failures I've found:

1) Make sure wifi powersaving is enabled (iw dev wlp1s0 set power_save on)
2) Connect to any wifi network (makes firmware go into wifi powersaving
mode, not deep sleep)
3) Make sure bluetooth is turned off (to ensure the firmware actually
enters powersave mode and doesn't keep the radio active doing bluetooth
stuff)
4) To confirm that wifi powersaving is entered ping a device on the LAN,
pings should be a few ms higher than without powersaving
5) Run "while true; do iwconfig; sleep 0.0001; done", this wakes and
suspends the firmware extremely often
6) Wait until things explode, for me it consistently takes <5 minutes

BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=109681
Cc: stable@vger.kernel.org
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211011133224.15561-3-verdre@v0yd.nl

mwifiex: Read a PCI register after writing the TX ring write pointer

On the 88W8897 PCIe+USB card the firmware randomly crashes after setting
the TX ring write pointer. The issue is present in the latest firmware
version 15.68.19.p21 of the PCIe+USB card.

Those firmware crashes can be worked around by reading any PCI register
of the card after setting that register, so read the PCI_VENDOR_ID
register here. The reason this works is probably because we keep the bus
from entering an ASPM state for a bit longer, because that's what causes
the cards firmware to crash.

This fixes a bug where during RX/TX traffic and with ASPM L1 substates
enabled (the specific substates where the issue happens appear to be
platform dependent), the firmware crashes and eventually a command
timeout appears in the logs.

BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=109681
Cc: stable@vger.kernel.org
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211011133224.15561-2-verdre@v0yd.nl

wireless: Remove redundant 'flush_workqueue()' calls

'destroy_workqueue()' already drains the queue before destroying it, so
there is no need to flush it explicitly.

Remove the redundant 'flush_workqueue()' calls.

This was generated with coccinelle:

@@
expression E;
@@
- flush_workqueue(E);
destroy_workqueue(E);

Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/0855d51423578ad019c0264dad3fe47a2e8af9c7.1633849511.git.christophe.jaillet@wanadoo.fr

mt7601u: Remove redundant initialization of variable ret

The variable ret is being initialized with a value that is never read,
it is assigned later on with a different value. The initialization is
redundant and can be removed.

Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211007234153.31222-1-colin.king@canonical.com

rtlwifi: rtl8192ee: Remove redundant initialization of variable version

The variable version is being initialized with a value that is
never read, it is being updated afterwards in both branches of
an if statement. The assignment is redundant and can be removed.

Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211007163722.20165-1-colin.king@canonical.com

rtw89: add Realtek 802.11ax driver

This driver named rtw89, which is the next generation of rtw88, supports
Realtek 8852AE 802.11ax 2x2 chip whose new features are OFDMA, DBCC,
Spatial reuse, TWT and BSS coloring; now some of them aren't implemented
though.

The chip architecture is entirely different from the chips supported by
rtw88 like RTL8822CE 802.11ac chip. First of all, register address ranges
are totally redefined, so it's impossible to reuse register definition. To
communicate with firmware, new H2C/C2H format is proposed. In order to have
better utilization, TX DMA flow is changed to two stages DMA. To provide
rich RX status information, additional RX PPDU packets are added.

Since there are so many differences mentioned above, we decide to propose
a new driver. It has many authors, they are listed in alphabetic order:

Chin-Yen Lee <timlee@realtek.com>
Ping-Ke Shih <pkshih@realtek.com>
Po Hao Huang <phhuang@realtek.com>
Tzu-En Huang <tehuang@realtek.com>
Vincent Fann <vincent_fann@realtek.com>
Yan-Hsuan Chuang <tony0620emma@gmail.com>
Zong-Zhe Yang <kevin_yang@realtek.com>

Tested-by: Aaron Ma <aaron.ma@canonical.com>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211008035627.19463-1-pkshih@realtek.com

ath10k: fix max antenna gain unit

Most of the txpower for the ath10k firmware is stored as twicepower (0.5 dB
steps). This isn't the case for max_antenna_gain - which is still expected
by the firmware as dB.

The firmware is converting it from dB to the internal (twicepower)
representation when it calculates the limits of a channel. This can be seen
in tpc_stats when configuring "12" as max_antenna_gain. Instead of the
expected 12 (6 dB), the tpc_stats shows 24 (12 dB).

Tested on QCA9888 and IPQ4019 with firmware 10.4-3.5.3-00057.

Fixes: 02256930d9b8 ("ath10k: use proper tx power unit")
Signed-off-by: Sven Eckelmann <seckelmann@datto.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20190611172131.6064-1-sven@narfation.org

ath9k: fix an IS_ERR() vs NULL check

The devm_kmemdup() function doesn't return error pointers, it returns
NULL on error.

Fixes: eb3a97a69be8 ("ath9k: fetch calibration data via nvmem subsystem")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211011123533.GA15188@kili

ath11k: Identify DFS channel when sending scan channel list command

WMI_CHAN_INFO_DFS flag should be set when configuring a DFS channel
included in scan channel list. Without it, firmware will not send a
probe request frame which is needed in connection to an AP configured
with hidden SSID/network_id. So fix this to allow probe request frames
to be sent in cases where a beacon frame has been seen on the channel
first.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1

Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211011054919.77071-1-bqiang@codeaurora.org

ath9k: support DT ieee80211-freq-limit property to limit channels

The common DT property can be used to limit the available channels
but ath9k has to manually call wiphy_read_of_freq_limits().

I would have put this into ath9k_of_init(). But it didn't work there.
The reason is that in ath9k_of_init() the channels and bands are not yet
registered in the wiphy struct. So there isn't any channel to flag as
disabled.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211009212847.1781986-1-chunkeey@gmail.com