OSDN Git Service
Ron Rindjunsky [Mon, 21 Apr 2008 22:41:53 +0000 (15:41 -0700)]
iwlwifi: expanding HW parameters control
This patch adds several parameters to priv.hw_params, for better control
over HW capabilities variants
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Mon, 21 Apr 2008 22:41:52 +0000 (15:41 -0700)]
iwlwifi: changing EEPROM layout handling
This patch
1. changes the current EEPROM handling through a single HW struct
layout representation, to more general approach, treating the EEPROM
image as a flat bytes array, handling this image through ops functions
and offsets.
2. Eeprom is dynamically allocated accroding HW type
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mohamed Abbas [Mon, 21 Apr 2008 22:41:51 +0000 (15:41 -0700)]
iwlwifi: Add power level support
Add power level support
Signed-off-by: Mohamed Abbas <mabbas@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adrian Bunk [Mon, 21 Apr 2008 08:48:34 +0000 (11:48 +0300)]
remove ieee80211_wx_{get,set}_auth()
After the bcm43xx removal ieee80211_wx_{get,set}_auth() were no longer
used.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adrian Bunk [Mon, 21 Apr 2008 08:48:28 +0000 (11:48 +0300)]
remove ieee80211_tx_frame()
After the softmac removal ieee80211_tx_frame() was no longer used.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adrian Bunk [Mon, 21 Apr 2008 08:47:51 +0000 (11:47 +0300)]
make sta_rx_agg_session_timer_expired() static
sta_rx_agg_session_timer_expired() can now become static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michael Buesch [Sun, 20 Apr 2008 14:23:26 +0000 (16:23 +0200)]
b43: Remove some dead code
This patch removes some dead code from the driver.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Michael Buesch [Sun, 20 Apr 2008 14:03:32 +0000 (16:03 +0200)]
b43: Rewrite LO calibration algorithm
This patch distributes the Local Oscillator calibration bursts over time,
so that calibration only happens when it's actually needed.
Currently we periodically perform a recalibration of the whole table.
The table is huge and this takes lots of time. Additionally only small bits
of the table are actually needed at a given time. So instead of maintaining
a huge table with all possible calibration values, we create dynamic calibration
settings that
a) We only calibrate when they are actually needed.
b) Are cached for some time until they expire.
So a recalibration might happen if we need a calibration setting that's not
cached, or if the active calibration setting expires.
Currently the expire timeout is set to 30 seconds. We may raise that in future.
This patch reduces overall memory consumption by nuking the
huge static calibration tables.
This patch has been tested on several 4306, 4311 and 4318 flavours.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry.Finger@lwfinger.net [Sat, 19 Apr 2008 14:24:09 +0000 (16:24 +0200)]
ssb: Allow reading of 440-byte SPROM that is not rev 4
The current code checks for the special signature that signifies
a revision 4 SPROM. Now that a rev. 8 SPROM with a 440-byte length
has been found that may not have any special code, this check could
be relaxed. With this patch, if the CRC is incorrect for a 256-byte
SPROM, the code will immediately check for a 440-byte SPROM. If there
is still a CRC error, the size is set to 440 bytes, which allows dumping
of most of any 512-byte SPROM if one is encountered.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ester Kummer [Thu, 17 Apr 2008 23:05:14 +0000 (16:05 -0700)]
mac80211: correct skb allocation
This patch corrects the allocation of skb in ADDBA req/resp and DELBA
it removes redundant space u.addba_* are already counted in sizeof(*mgmt)
Signed-off-by: Ester Kummer <ester.kummer@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Thu, 17 Apr 2008 23:03:39 +0000 (16:03 -0700)]
iwlwifi: export int iwl4965_set_pwr_src
This handler is universal for most of the HW
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Thu, 17 Apr 2008 23:03:38 +0000 (16:03 -0700)]
iwlwifi: define ANA_PLL values in iwl-csr.h
This patch defines ANA_PLL values in iwl-csr.h
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ron Rindjunsky [Thu, 17 Apr 2008 23:03:37 +0000 (16:03 -0700)]
iwlwifi: arranging aggregation actions
This patch makes some renaming of the ampdu_action functions inside
iwlwifi, and adds checks for correct station id in Rx flows
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Thu, 17 Apr 2008 23:03:36 +0000 (16:03 -0700)]
iwlwifi: HW crypto acceleration fixes
This patch fixes several issues in security:
1) the uCode doesn't know about TKIP-MMIC failure, if uCode set
RX_RES_STATUS_BAD_ICV_MIC, it means ICV failure: drop the packet silently.
2) do not allocate room in the key table of the uCode is the set_key call
is a replacement of an old key
3) check the keyidx of the key in the uCode before removing it upon
disable_key call
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Thu, 17 Apr 2008 19:11:18 +0000 (21:11 +0200)]
mac80211: Add IEEE80211_KEY_FLAG_PAIRWISE
This adds a new flag to the ieee80211_key_conf structure.
This flag will inform the driver the key is pairwise rather then
a shared key.
This is important for drivers who support both types of keys,
and need to be informed which type of key this is. Alternative
would be drivers checking the address argument of set_key(),
but it will be safer when mac80211 is more explicit.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 17 Apr 2008 17:21:22 +0000 (19:21 +0200)]
mac80211: a few code cleanups
This has some code cleanups (some inspired by checkpatch), I got
bored at probably a third of the output though so if somebody
else wants to...
Signed-off-by: Johannes Berg <johannes@sipsolutions.net
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn [Thu, 17 Apr 2008 17:41:02 +0000 (19:41 +0200)]
mac80211: Replace ieee80211_tx_control->key_idx with ieee80211_key_conf
The hw_key_idx inside the ieee80211_key_conf structure does
not provide all the information drivers might need to perform
hardware encryption.
This is in particular true for rt2x00 who needs to know the
key algorithm and whether it is a shared or pairwise key.
By passing the ieee80211_key_conf pointer it assures us that
drivers can make full use of all information that it should know
about a particular key.
Additionally this patch updates all drivers to grab the hw_key_idx from
the ieee80211_key_conf structure.
v2: Removed bogus u16 cast
v3: Add warning about ieee80211_tx_control pointers
v4: Update warning about ieee80211_tx_control pointers
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Wed, 16 Apr 2008 23:34:49 +0000 (16:34 -0700)]
iwlwifi: cleanup set_pwr_src
This patch cleans up semantic of set_pwr_src
set_pwr_src is now part of apm handlers group
in iwlcore
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tomas Winkler [Wed, 16 Apr 2008 23:34:48 +0000 (16:34 -0700)]
iwlwifi: move find station to iwl-sta.c
This patch move iwl_find_station into iwl-sta.c file
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Wed, 16 Apr 2008 23:34:47 +0000 (16:34 -0700)]
iwlwifi: HW dependent run time calibration
This patch does several things:
1) rename CONFIG_IWL4965_SENSITIVITY to IWL4965_RUN_TIME_CALIB which is
better semantic
2) move all the run time calibration to a new file: iwl-calib.c
3) simplify the sensitivity calibration flow and make it HW dependent
4) make the chain noise calibration flow HW dependent
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allan Stephens [Mon, 5 May 2008 08:24:36 +0000 (01:24 -0700)]
tipc: Update version number to TIPC 1.6.4
This patch updates TIPC's version number to 1.6.4.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allan Stephens [Mon, 5 May 2008 08:24:06 +0000 (01:24 -0700)]
tipc: Exclude debug-only print buffer code when not debugging
This patch modifies TIPC to only exclude debug-related print buffer
routines when debugging capabilities are not required. It also
fixes up some related #defines that exceed 80 characters.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allan Stephens [Mon, 5 May 2008 08:23:34 +0000 (01:23 -0700)]
tipc: Cosmetic cleanup of system & debug output declarations
This patch contains changes to make TIPC's system & debug
message declarations more readable. Declarations have been
regrouped and recommented to make it easier to understand
what output is generated in both standard and debugging modes.
In addition, oversize lines have been fixed to respect the
80 character upper bound used in the kernel.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allan Stephens [Mon, 5 May 2008 08:22:59 +0000 (01:22 -0700)]
[TIPC]: Cosmetic cleanup of print buffer code
This patch contains changes to make TIPC's print buffer code
conform more closely to Linux kernel coding guidelines.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allan Stephens [Mon, 5 May 2008 08:22:30 +0000 (01:22 -0700)]
tipc: Elimination of print buffer chaining
This patch revamps TIPC's print buffer subsystem to eliminate
support for arbitrary chains of print buffers, which were
rarely needed and difficult to use safely.
In its place, print buffers can now be configured to echo their
output to the system console. This provides an equivalent for
the only chaining currently utilized by TIPC, in a faster and
more compact manner.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allan Stephens [Mon, 5 May 2008 08:21:54 +0000 (01:21 -0700)]
tipc: Fix null pointer dereference in debug code
This patch eliminates an obsolete use of the DBG_OUTPUT print
buffer which could lead to a null pointer crash in tipc_printf()
if TIPC's debugging capabilities are configured.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allan Stephens [Mon, 5 May 2008 08:21:12 +0000 (01:21 -0700)]
tipc: Fix recursive spinlock invocation in print buffer code
This patch fixes two routines that allow the global print buffer
spinlock to be taken recursively.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allan Stephens [Mon, 5 May 2008 08:20:42 +0000 (01:20 -0700)]
tipc: Provide feedback when log buffer resizing fails
This patch provides feedback to the user when TIPC is unable
to set its log buffer to the requested size.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allan Stephens [Mon, 5 May 2008 08:20:04 +0000 (01:20 -0700)]
tipc: Simplify log buffer resizing
This patch simplifies & standardizes the way TIPC's print buffer
log is resized. Code to terminate use of the log buffer is
eliminated by simply setting the log buffer size to 0 bytes.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 5 May 2008 00:12:10 +0000 (17:12 -0700)]
Merge git://git./linux/kernel/git/hpa/linux-2.6-inttypes
* git://git.kernel.org/pub/scm/linux/kernel/git/hpa/linux-2.6-inttypes:
fix asm-mips/types.h syntax error
fix asm-alpha/types.h breakage
Linus Torvalds [Mon, 5 May 2008 00:11:43 +0000 (17:11 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/x86/linux-2.6-x86-fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86-fixes:
x86: fix setup printk format warning
x86: olpc build fix
x86: video/fbdev.c: add MODULE_LICENSE
x86: fix up bootparam.h for userspace inclusion
x86: relocs ELF handling - use SELFMAG instead of numeric constant
x86: vdso ELF handling - use SELFMAG instead of numeric constant
x86: remove dell reboot dmi quirk board name match
x86: es7000 build fix
x86: make additional_cpus static
x86: make start_secondary() static
kbuild, suspend, x86: fix rebuild of wakeup.bin
uml: fix gcc problem
x86: undo visws/numaq build changes
Linus Torvalds [Mon, 5 May 2008 00:11:24 +0000 (17:11 -0700)]
Merge git://git./linux/kernel/git/sam/kbuild-fixes
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-fixes:
kconfig-language.txt: remove bogus hint
kconfig: fix MAC OS X warnings in menuconfig
modpost: i2c aliases need no trailing wildcard
Bryan Wu [Sun, 4 May 2008 15:12:55 +0000 (23:12 +0800)]
task_nommu: fix compile failing bug because of spilt file.h
CC fs/proc/task_nommu.o
fs/proc/task_nommu.c: In function ‘task_mem’:
fs/proc/task_nommu.c:55: error: dereferencing pointer to incomplete type
make[2]: *** [fs/proc/task_nommu.o] Error 1
make[1]: *** [fs/proc] Error 2
make: *** [fs] Error 2
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Mon, 5 May 2008 00:08:21 +0000 (17:08 -0700)]
Merge git://git./linux/kernel/git/bart/ide-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
ide: IDE_HFLAG_SERIALIZE_DMA bugfix
Linus Torvalds [Mon, 5 May 2008 00:07:28 +0000 (17:07 -0700)]
Merge branch 'kvm-updates-2.6.26' of git://git./linux/kernel/git/avi/kvm
* 'kvm-updates-2.6.26' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm:
x86: KVM geust: make setup_secondary_clock definition dependent on local apic
KVM: MMU: Allow more than PAGES_PER_HPAGE write protections per large page
KVM: avoid fx_init() schedule in atomic
KVM: Avoid spurious execeptions after setting registers
KVM: PIT: support mode 4
KVM: x86 emulator: disable writeback on lmsw
KVM: ppc: deliver INTERRUPT_FP_UNAVAIL to the guest
KVM: ppc: Handle guest idle by emulating MSR[WE] writes
KVM: x86: task switch: fix wrong bit setting for the busy flag
KVM: VMX: Enable EPT feature for KVM
KVM: VMX: Prepare an identity page table for EPT in real mode
KVM: Export necessary function for EPT
KVM: MMU: Remove #ifdef CONFIG_X86_64 to support 4 level EPT
KVM: MMU: Add EPT support
KVM: Add kvm_x86_ops get_tdp_level()
KVM: MMU: Move some definitions to a header file
KVM: VMX: EPT Feature Detection
Ingo Molnar [Sun, 4 May 2008 07:29:43 +0000 (09:29 +0200)]
sysfs: build fix
x86.git testing found the following build failure on v2.6.26-rc1:
In file included from include/linux/kobject.h:22,
from include/linux/module.h:17,
from include/linux/crypto.h:22,
from arch/x86/kernel/asm-offsets_32.c:8,
from arch/x86/kernel/asm-offsets.c:3:
include/linux/sysfs.h:201: error: redefinition of 'sysfs_update_group'
include/linux/sysfs.h:195: error: previous definition of 'sysfs_update_group' was here
make[1]: *** [arch/x86/kernel/asm-offsets.s] Error 1
make: *** [prepare0] Error 2
with the following config:
http://redhat.com/~mingo/misc/config-Sun_May__4_07_09_30_CEST_2008.bad
the reason for the build failure is the duplicate definition of the
sysfs_update_group() inline function in include/linux/sysfs.h.
The duplication was a merge error: it was added via -mm by commit
v2.6.25-7262-g2850699, "sysfs: sysfs_update_group stub for
CONFIG_SYSFS=n" a day before v2.6.26-rc1, but a day before that the same
commit was already merged upstream via the sysfs tree, with commit
v2.6.25-7211-g1cbfb7a.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Mon, 5 May 2008 00:04:16 +0000 (17:04 -0700)]
Make forced module loading optional
The kernel module loader used to be much too happy to allow loading of
modules for the wrong kernel version by default. For example, if you
had MODVERSIONS enabled, but tried to load a module with no version
info, it would happily load it and taint the kernel - whether it was
likely to actually work or not!
Generally, such forced module loading should be considered a really
really bad idea, so make it conditional on a new config option
(MODULE_FORCE_LOAD), and make it default to off.
If somebody really wants to force module loads, that's their problem,
but we should not encourage it. Especially as it happened to me by
mistake (ie regular unversioned Fedora modules getting loaded) causing
lots of strange behavior.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adrian Bunk [Sat, 3 May 2008 19:26:17 +0000 (22:26 +0300)]
fix asm-mips/types.h syntax error
This patch fixes the following compile error caused by
commit
23cf11ddb5099f8c7f7cb3eb154bff0faf31cae9
(mips: types: use <asm-generic/int-*.h> for the mips architecture):
<-- snip -->
...
CC kernel/bounds.s
In file included from /home/bunk/linux/kernel-2.6/git/linux-2.6/include/linux/types.h:12,
from /home/bunk/linux/kernel-2.6/git/linux-2.6/include/linux/page-flags.h:8,
from /home/bunk/linux/kernel-2.6/git/linux-2.6/kernel/bounds.c:9:
include2/asm/types.h:56:2: error: #endif without #if
make[2]: *** [kernel/bounds.s] Error 1
<-- snip -->
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Adrian Bunk [Sat, 3 May 2008 20:51:03 +0000 (23:51 +0300)]
fix asm-alpha/types.h breakage
This patch fixes the following compile error on alpha caused by
commit
3726c23df8e4d95b6f2b335dfa90e3f4850a8a00
(alpha: types: use <asm-generic/int-*.h> for the alpha architecture):
<-- snip -->
...
CC arch/alpha/kernel/asm-offsets.s
In file included from include2/asm/topology.h:6,
from /home/bunk/linux/kernel-2.6/git/linux-2.6/include/linux/topology.h:34,
from /home/bunk/linux/kernel-2.6/git/linux-2.6/include/linux/mmzone.h:683,
from /home/bunk/linux/kernel-2.6/git/linux-2.6/include/linux/gfp.h:4,
from /home/bunk/linux/kernel-2.6/git/linux-2.6/include/linux/slab.h:12,
from /home/bunk/linux/kernel-2.6/git/linux-2.6/include/linux/percpu.h:5,
from /home/bunk/linux/kernel-2.6/git/linux-2.6/include/linux/rcupdate.h:39,
from /home/bunk/linux/kernel-2.6/git/linux-2.6/include/linux/pid.h:4,
from /home/bunk/linux/kernel-2.6/git/linux-2.6/include/linux/sched.h:74,
from /home/bunk/linux/kernel-2.6/git/linux-2.6/arch/alpha/kernel/asm-offsets.c:9:
include2/asm/machvec.h:44: error: expected declaration specifiers or '...' before 'dma_addr_t'
include2/asm/machvec.h:44: error: expected declaration specifiers or '...' before 'dma_addr_t'
In file included from /home/bunk/linux/kernel-2.6/git/linux-2.6/arch/alpha/kernel/asm-offsets.c:12:
include2/asm/io.h:94: warning: type defaults to 'int' in declaration of 'dma_addr_t'
include2/asm/io.h:94: warning: variable 'dma_addr_t' declared 'inline'
include2/asm/io.h:94: error: expected ',' or ';' before 'isa_page_to_bus'
make[2]: *** [arch/alpha/kernel/asm-offsets.s] Error 1
<-- snip -->
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Adrian Bunk [Sat, 3 May 2008 23:15:35 +0000 (02:15 +0300)]
kconfig-language.txt: remove bogus hint
For the use case the hint describe a simple dependency is
enough.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Sam Ravnborg [Sun, 4 May 2008 19:03:20 +0000 (21:03 +0200)]
kconfig: fix MAC OS X warnings in menuconfig
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Timur Tabi <timur@freescale.com>
Randy Dunlap [Fri, 2 May 2008 20:32:35 +0000 (13:32 -0700)]
x86: fix setup printk format warning
Fix x86 setup printk format warming:
next-
20080430/arch/x86/kernel/setup.c:172: warning: format '%lu' expects type 'long unsigned int', but argument 2 has type 'ssize_t'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: mingo@elte.hu
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Thomas Gleixner [Sat, 3 May 2008 21:49:59 +0000 (23:49 +0200)]
x86: olpc build fix
CONFIG_OLPC needs to depend on MGEODE_LX
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Adrian Bunk [Fri, 2 May 2008 20:32:32 +0000 (13:32 -0700)]
x86: video/fbdev.c: add MODULE_LICENSE
Add the missing MODULE_LICENSE("GPL").
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Rusty Russell [Fri, 2 May 2008 11:14:20 +0000 (21:14 +1000)]
x86: fix up bootparam.h for userspace inclusion
commit
8b664aa66e824a0ddf4ec56d41fa0cf7bb374de6 (x86, boot: add linked
list of struct setup_data) put a new struct in bootparam.h, but didn't
use the userspace-safe types.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Huang Ying <ying.huang@intel.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cyrill Gorcunov [Sat, 3 May 2008 10:18:03 +0000 (14:18 +0400)]
x86: relocs ELF handling - use SELFMAG instead of numeric constant
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: akpm@linux-foundation.org
Cc: hpa@zytor.com
Cc: mingo@elte.hu
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cyrill Gorcunov [Sat, 3 May 2008 10:18:01 +0000 (14:18 +0400)]
x86: vdso ELF handling - use SELFMAG instead of numeric constant
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: akpm@linux-foundation.org
Cc: hpa@zytor.com
Cc: mingo@elte.hu
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Ben [Sat, 3 May 2008 20:39:42 +0000 (22:39 +0200)]
x86: remove dell reboot dmi quirk board name match
http://bugzilla.kernel.org/show_bug.cgi?id=10547
Newer Dell OptiPlex 745s hang before rebooting after 'sudo reboot'.
A patch for some versions of the OptiPlex was proposed here --
http://lkml.org/lkml/2007/6/5/59 -- and is included in 2.6.23 and
later kernels, according to
http://lxr.linux.no/linux+v2.6.23/arch/i386/kernel/reboot.c . However,
the DMI_BOARD_NAME ("0WF810") is too restrictive. Newer OptiPlex
machines have a DMI_BOARD_NAME of "0RF703". I therefore suggest
adding another clause to reboot.c, similar to the one in the original
patch, but matching a DMI_BOARD_NAME of "0RF703".
On further inspection, it seems that there are other DMI_BOARD_NAMEs
for this same machine. They seem to change from time to time, which
means that the current code is fragile. Moreover, using bios reboot
should not break non-SFF OptiPlex 745s, and so a reasonable fix is to
simply drop the match on DMI_BOARD_NAME.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Ingo Molnar [Sat, 3 May 2008 20:01:31 +0000 (22:01 +0200)]
x86: es7000 build fix
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Adrian Bunk [Mon, 21 Apr 2008 21:31:37 +0000 (00:31 +0300)]
x86: make additional_cpus static
This patch makes the needlessly global additional_cpus static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Adrian Bunk [Mon, 21 Apr 2008 22:50:26 +0000 (01:50 +0300)]
x86: make start_secondary() static
start_secondary() needlessly became global.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Sam Ravnborg [Thu, 1 May 2008 09:31:07 +0000 (11:31 +0200)]
kbuild, suspend, x86: fix rebuild of wakeup.bin
In kernel/acpi/realmode/Makefile use the 'always'
variable to say that wakeup.bin should always
be made.
In acpi/Makefile we then do not need to specify the
requested target and we avoid the message from make:
`arch/x86/kernel/acpi/realmode/wakeup.bin' is up to date.
Add wakeup.lds to list af targets to avoid rebuilding
wakeup.bin - from Roland McGrath.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Pavel Machek <pavel@suse.cz>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Ingo Molnar [Thu, 1 May 2008 10:06:54 +0000 (12:06 +0200)]
uml: fix gcc problem
this is what caused gcc 4.3 to throw an internal error when
OPTIMIZE_INLINING was enabled ...
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Fri, 2 May 2008 19:24:30 +0000 (21:24 +0200)]
x86: undo visws/numaq build changes
arch/x86/pci/Makefile_32 has a nasty detail. VISWS and NUMAQ build
override the generic pci-y rules. This needs a proper cleanup, but
that needs more thoughts. Undo
commit
895d30935ebe05f192e844792668bf8d19deaae7
x86: numaq fix
do not override the existing pci-y rule when adding visws or
numaq rules.
There is also a stupid init function ordering problem vs. acpi.o
Add comments to the Makefile to avoid tripping over this again.
Remove the srat stub code in discontig_32.c to allow a proper NUMAQ
build.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Bartlomiej Zolnierkiewicz [Sun, 4 May 2008 15:03:41 +0000 (17:03 +0200)]
ide: IDE_HFLAG_SERIALIZE_DMA bugfix
Patch re-ordering could be harmful:
commit
1fd1890594bd355a4217f5658a34763e77decee3
Author: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Date: Sat Apr 26 22:25:24 2008 +0200
ide: add IDE_HFLAG_SERIALIZE_DMA host flag
...
is buggy because ->init_dma method / ide_hwif_setup_dma() is called
before IDE_HFLAG_SERIALIZE_DMA host flag is checked.
Fix it by checking IDE_HFLAG_SERIALIZE[_DMA] after DMA initialization.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Glauber Costa [Wed, 30 Apr 2008 15:39:05 +0000 (12:39 -0300)]
x86: KVM geust: make setup_secondary_clock definition dependent on local apic
Since the pv_apic_ops are only present if CONFIG_X86_LOCAL_APIC is compiled
in, kvmclock failed to build without this option. This patch fixes this.
Signed-off-by: Glauber Costa <gcosta@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Avi Kivity [Fri, 2 May 2008 10:23:10 +0000 (13:23 +0300)]
KVM: MMU: Allow more than PAGES_PER_HPAGE write protections per large page
nonpae guests can call rmap_write_protect twice per page (for page tables)
or four times per page (for page directories), triggering a bogus warning.
Remove the warning.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Andrea Arcangeli [Thu, 1 May 2008 16:43:33 +0000 (18:43 +0200)]
KVM: avoid fx_init() schedule in atomic
This make sure not to schedule in atomic during fx_init. I also
changed the name of fpu_init to fx_finit to avoid duplicating the name
with fpu_init that is already used in the kernel, this makes grep
simpler if nothing else.
Signed-off-by: Andrea Arcangeli <andrea@qumranet.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Jan Kiszka [Wed, 30 Apr 2008 15:59:04 +0000 (17:59 +0200)]
KVM: Avoid spurious execeptions after setting registers
Clear pending exceptions when setting new register values. This avoids
spurious exceptions after restoring a vcpu state or after
reset-on-triple-fault.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Marcelo Tosatti [Wed, 30 Apr 2008 16:23:54 +0000 (13:23 -0300)]
KVM: PIT: support mode 4
The in-kernel PIT emulation ignores pending timers if operating under
mode 4, which for example DragonFlyBSD uses (and Plan9 too, apparently).
Mode 4 seems to be similar to one-shot mode, other than the fact that it
starts counting after the next CLK pulse once programmed, while mode 1
starts counting immediately, so add a FIXME to enhance precision.
Fixes sourceforge bug
1952988.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Acked-by: Sheng Yang <sheng.yang@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Avi Kivity [Wed, 30 Apr 2008 13:13:36 +0000 (16:13 +0300)]
KVM: x86 emulator: disable writeback on lmsw
The recent changes allowing memory operands with lmsw and smsw left
lmsw with writeback enabled. Since lmsw has no oridinary destination
operand, the dst pointer was not initialized, resulting in an oops.
Close the hole by disabling writeback for lmsw.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Christian Ehrhardt [Tue, 29 Apr 2008 16:18:23 +0000 (18:18 +0200)]
KVM: ppc: deliver INTERRUPT_FP_UNAVAIL to the guest
This patch adds the delivery of INTERRUPT_FP_UNAVAIL exceptions to the guest.
It's needed if a guest uses ppc binaries using the Floating point instructions.
Signed-off-by: Christian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Acked-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Hollis Blanchard [Fri, 25 Apr 2008 22:55:49 +0000 (17:55 -0500)]
KVM: ppc: Handle guest idle by emulating MSR[WE] writes
This reduces host CPU usage when the guest is idle. However, the guest must
set MSR[WE] in its idle loop, which Linux did not do until 2.6.26.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Jerone Young <jyoung5@us.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Izik Eidus [Mon, 28 Apr 2008 15:23:52 +0000 (18:23 +0300)]
KVM: x86: task switch: fix wrong bit setting for the busy flag
The busy bit is bit 1 of the type field, not bit 8.
Signed-off-by: Izik Eidus <izike@qumranet.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Sheng Yang [Mon, 28 Apr 2008 04:24:45 +0000 (12:24 +0800)]
KVM: VMX: Enable EPT feature for KVM
Signed-off-by: Sheng Yang <sheng.yang@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Sheng Yang [Fri, 25 Apr 2008 13:44:52 +0000 (21:44 +0800)]
KVM: VMX: Prepare an identity page table for EPT in real mode
[aliguory: plug leak]
Signed-off-by: Sheng Yang <sheng.yang@intel.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Sheng Yang [Fri, 25 Apr 2008 13:44:50 +0000 (21:44 +0800)]
KVM: Export necessary function for EPT
Signed-off-by: Sheng Yang <sheng.yang@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Sheng Yang [Fri, 25 Apr 2008 13:44:42 +0000 (21:44 +0800)]
KVM: MMU: Remove #ifdef CONFIG_X86_64 to support 4 level EPT
Currently EPT level is 4 for both pae and x86_64. The patch remove the #ifdef
for alloc root_hpa and free root_hpa to support EPT.
Signed-off-by: Sheng Yang <sheng.yang@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Sheng Yang [Fri, 25 Apr 2008 13:13:50 +0000 (21:13 +0800)]
KVM: MMU: Add EPT support
Enable kvm_set_spte() to generate EPT entries.
Signed-off-by: Sheng Yang <sheng.yang@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Sheng Yang [Fri, 25 Apr 2008 02:20:22 +0000 (10:20 +0800)]
KVM: Add kvm_x86_ops get_tdp_level()
The function get_tdp_level() provided the number of tdp level for EPT and
NPT rather than the NPT specific macro.
Signed-off-by: Sheng Yang <sheng.yang@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Sheng Yang [Fri, 25 Apr 2008 02:17:08 +0000 (10:17 +0800)]
KVM: MMU: Move some definitions to a header file
Move some definitions to mmu.h in order to allow building common table
entries between EPT and non-EPT.
Signed-off-by: Sheng Yang <sheng.yang@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Sheng Yang [Fri, 25 Apr 2008 02:13:16 +0000 (10:13 +0800)]
KVM: VMX: EPT Feature Detection
Signed-off-by: Sheng Yang <sheng.yang@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Jean Delvare [Fri, 2 May 2008 18:37:21 +0000 (20:37 +0200)]
modpost: i2c aliases need no trailing wildcard
Not all device types need a wildcard at the end of their module
aliases. In particular, for i2c module aliases, the trailing wildcard
is not only unneeded, it could also cause the wrong driver to be
loaded.
As I2C devices have no IDs, i2c module aliases are simple, arbitrary
device names. For example:
$ /sbin/modinfo lm90
filename: /lib/modules/2.6.25-git18/kernel/drivers/hwmon/lm90.ko
author: Jean Delvare <khali@linux-fr.org>
description: LM90/ADM1032 driver
license: GPL
vermagic: 2.6.25-git18 mod_unload
depends: hwmon
alias: i2c:lm90*
alias: i2c:adm1032*
alias: i2c:lm99*
alias: i2c:lm86*
alias: i2c:max6657*
alias: i2c:adt7461*
alias: i2c:max6680*
$
This would cause trouble if one I2C chip name matches the beginning of
another I2C chip name and both chips are supported by different
drivers. For example, an i2c device named lm9042 would cause the lm90
driver to be loaded, while it doesn't support that device. This case
has yet to be seen in practice, but still, I'd like to fix it now. The
cleanest fix is to remove the trailing wildcard from i2c module aliases.
Here's a patch doing this.
Not all device type aliases need a trailing wildcard, in particular
the i2c aliases don't. Don't add a wildcard by default in do_table(),
instead let each device type handler add it if needed.
I have tested types acpi, dmi, eisa, i2c, ide, ieee1394, input, pci,
pcmcia, platform, pnp, scsi, serio, ssb and usb. Other types (ccw, of,
vio, parisc, sdio and virtio) are untested.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Linus Torvalds [Sat, 3 May 2008 20:51:10 +0000 (13:51 -0700)]
Merge git://git./linux/kernel/git/tglx/linux-2.6-hrt
* git://git.kernel.org/pub/scm/linux/kernel/git/tglx/linux-2.6-hrt:
clocksource: allow read access to available/current_clocksource
clocksource: Fix permissions for available_clocksource
hrtimer: remove duplicate helper function
Ulrich Drepper [Sat, 3 May 2008 19:28:45 +0000 (15:28 -0400)]
tiny mq_open optimization
A very small cleanup for mq_open.
We do not have to call set_close_on_exit if we create the file
descriptor right away with the flag set. We have a function for this
now. The resulting code is smaller and a tiny bit faster.
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ulrich Drepper [Sat, 3 May 2008 19:10:37 +0000 (15:10 -0400)]
unified (weak) sys_pipe implementation
This replaces the duplicated arch-specific versions of "sys_pipe()" with
one unified implementation. This removes almost 250 lines of duplicated
code.
It's marked __weak, so that *if* an architecture wants to override the
default implementation it can do so by simply having its own replacement
version, since many architectures use alternate calling conventions for
the 'pipe()' system call for legacy reasons (ie traditional UNIX
implementations often return the two file descriptors in registers)
I still haven't changed the cris version even though Linus says the BKL
isn't needed. The arch maintainer can easily do it if there are really
no obstacles.
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 3 May 2008 18:59:44 +0000 (11:59 -0700)]
Linux 2.6.26-rc1
Linus Torvalds [Sat, 3 May 2008 17:57:57 +0000 (10:57 -0700)]
Merge git://git.infradead.org/battery-2.6
* git://git.infradead.org/battery-2.6:
PMU battery: filenames in sysfs with spaces
pda_power: add init and exit function callbacks
Linus Torvalds [Sat, 3 May 2008 17:54:23 +0000 (10:54 -0700)]
Merge git://git./linux/kernel/git/hpa/linux-2.6-inttypes
* git://git.kernel.org/pub/scm/linux/kernel/git/hpa/linux-2.6-inttypes: (24 commits)
Make constants in kernel/timeconst.h fixed 64 bits
types: add C99-style constructors to <asm-generic/int-*.h>
xtensa: types: use <asm-generic/int-*.h> for the xtensa architecture
x86: types: use <asm-generic/int-*.h> for the x86 architecture
v850: types: use <asm-generic/int-*.h> for the v850 architecture
sparc64: types: use <asm-generic/int-*.h> for the sparc64 architecture
sparc: types: use <asm-generic/int-*.h> for the sparc architecture
sh: types: use <asm-generic/int-*.h> for the sh architecture
s390: types: use <asm-generic/int-*.h> for the s390 architecture
powerpc: types: use <asm-generic/int-*.h> for the powerpc architecture
parisc: types: use <asm-generic/int-*.h> for the parisc architecture
mn10300: types: use <asm-generic/int-*.h> for the mn10300 architecture
mips: types: use <asm-generic/int-*.h> for the mips architecture
m68k: types: use <asm-generic/int-*.h> for the m68k architecture
m32r: types: use <asm-generic/int-*.h> for the m32r architecture
ia64: types: use <asm-generic/int-*.h> for the ia64 architecture
h8300: types: use <asm-generic/int-*.h> for the h8300 architecture
frv: types: use <asm-generic/int-*.h> for the frv architecture
cris: types: use <asm-generic/int-*.h> for the cris architecture
blackfin: types: use <asm-generic/int-*.h> for the blackfin architecture
...
Jesse Barnes [Sat, 3 May 2008 15:35:49 +0000 (08:35 -0700)]
[MAINTAINERS] PCI list moved
Many thanks to Martin for his years of hosting. The pci list has moved to
vger, along with what seems like the rest of the major Linux mailing lists.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 3 May 2008 17:18:40 +0000 (10:18 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/penberg/slab-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6:
slub: #ifdef simplification
slabinfo: Support printout of the number of fallbacks
slub: Whitespace cleanup and use of strict_strtoul
Linus Torvalds [Sat, 3 May 2008 17:18:21 +0000 (10:18 -0700)]
Merge git://git./linux/kernel/git/davem/net-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (47 commits)
rose: Wrong list_lock argument in rose_node seqops
netns: Fix reassembly timer to use the right namespace
netns: Fix device renaming for sysfs
bnx2: Update version to 1.7.5.
bnx2: Update RV2P firmware for 5709.
bnx2: Zero out context memory for 5709.
bnx2: Fix register test on 5709.
bnx2: Fix remote PHY initial link state.
bnx2: Refine remote PHY locking.
bridge: forwarding table information for >256 devices
tg3: Update version to 3.92
tg3: Add link state reporting to UMP firmware
tg3: Fix ethtool loopback test for 5761 BX devices
tg3: Fix 5761 NVRAM sizes
tg3: Use constant 500KHz MI clock on adapters with a CPMU
hci_usb.h: fix hard-to-trigger race
dccp: ccid2.c, ccid3.c use clamp(), clamp_t()
net: remove NR_CPUS arrays in net/core/dev.c
net: use get/put_unaligned_* helpers
bluetooth: use get/put_unaligned_* helpers
...
Linus Torvalds [Sat, 3 May 2008 17:05:11 +0000 (10:05 -0700)]
Merge git://git./linux/kernel/git/davem/sparc-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc32: Delete prom_stdin and prom_stdout.
sparc32: More memory probing consolidation.
sparc32: Kill totally unused memory information tables.
sparc64: Fix syscall restart, for real...
serial: Fix sparc driver name strings.
sparc64: Stop creating dummy root PCI host controller devices.
Linus Torvalds [Sat, 3 May 2008 17:01:33 +0000 (10:01 -0700)]
Merge git://git./linux/kernel/git/paulus/powerpc
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Bolt in SLB entry for kernel stack on secondary cpus
[POWERPC] PS3: Update ps3_defconfig
[POWERPC] PS3: Remove unsupported wakeup sources
[POWERPC] PS3: Make ps3_virq_setup and ps3_virq_destroy static
[POWERPC] PS3: Add time include to lpm
[POWERPC] Fix slb.c compile warnings
[POWERPC] Xilinx: Fix compile warnings
[POWERPC] Squash build warning for print of resource_size_t in fsl_soc.c
[RAPIDIO] fix current kernel-doc notation
[POWERPC] 86xx: mpc8610_hpcd: add support for PCI Express x8 slot
Fix a potential issue in mpc52xx uart driver
[POWERPC] mpc5200: Allow for fixed speed MII configurations
[POWERPC] 86xx: Fix the wrong serial1 interrupt for 8610 board
Heiko Carstens [Sat, 3 May 2008 12:23:14 +0000 (14:23 +0200)]
clocksource: allow read access to available/current_clocksource
There is no harm, when users can read the info and we ask often enough
during debugging for this kind of information.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Heiko Carstens [Fri, 2 May 2008 10:49:40 +0000 (12:49 +0200)]
clocksource: Fix permissions for available_clocksource
File permissions for
/sys/devices/system/clocksource/clocksource0/available_clocksource
are 600 which allows write access. But this is in fact a read only
file. So change permissions to 400.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: John Stultz <johnstul@us.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Oliver Hartkopp [Wed, 30 Apr 2008 21:04:37 +0000 (23:04 +0200)]
hrtimer: remove duplicate helper function
The helper function hrtimer_callback_running() is used in
kernel/hrtimer.c as well as in the updated net/can/bcm.c which now
supports hrtimers. Moving the helper function to hrtimer.h removes the
duplicate definition in the C-files.
Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Bernard Pidoux [Sat, 3 May 2008 00:03:22 +0000 (17:03 -0700)]
rose: Wrong list_lock argument in rose_node seqops
In rose_node_start() as well as in rose_node_stop() __acquires() and
spin_lock_bh() were wrongly passing rose_neigh_list_lock instead of
rose_node_list_lock arguments.
Signed-off-by: Bernard Pidoux <f6bvp@amsat.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Lezcano [Sat, 3 May 2008 00:02:03 +0000 (17:02 -0700)]
netns: Fix reassembly timer to use the right namespace
This trivial fix retrieves the network namespace from frag queue
and use it to get the network device in the right namespace.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Lezcano [Sat, 3 May 2008 00:00:58 +0000 (17:00 -0700)]
netns: Fix device renaming for sysfs
When a netdev is moved across namespaces with the
'dev_change_net_namespace' function, the 'device_rename' function is
used to fixup kobject and refresh the sysfs tree. The device_rename
function will call kobject_rename and this one will check if there is
an object with the same name and this is the case because we are
renaming the object with the same name.
The use of 'device_rename' seems for me wrong because we usually don't
rename it but just move it across namespaces. As we just want to do a
mini "netdev_[un]register", IMO the functions
'netdev_[un]register_kobject' should be used instead, like an usual
network device [un]registering.
This patch replace device_rename by netdev_unregister_kobject,
followed by netdev_register_kobject.
The netdev_register_kobject will call device_initialize and will raise
a warning indicating the device was already initialized. In order to
fix that, I split the device initialization into a separate function
and use it together with 'netdev_register_kobject' into
register_netdevice. So we can safely call 'netdev_register_kobject' in
'dev_change_net_namespace'.
This fix will allow to properly use the sysfs per namespace which is
coming from -mm tree.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Acked-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Fri, 2 May 2008 23:58:18 +0000 (16:58 -0700)]
bnx2: Update version to 1.7.5.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Fri, 2 May 2008 23:57:59 +0000 (16:57 -0700)]
bnx2: Update RV2P firmware for 5709.
The new RV2P firmware fixes 2 issues:
1. The jumbo rx buffer page size is now configurable and set to the
proper PAGE_SIZE. Before, it was assumed to be always 4K.
2. Driver sometimes would crash when receiving jumbo packets mixed
with firmware management packets. This was caused by the old
firmware DMA'ing to the wrong address.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Fri, 2 May 2008 23:57:26 +0000 (16:57 -0700)]
bnx2: Zero out context memory for 5709.
We should zero out the context memory for 5709 before each reset. When
we resume after suspend for example, the memory may not be zero and the
chip may not function correctly.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Fri, 2 May 2008 23:57:08 +0000 (16:57 -0700)]
bnx2: Fix register test on 5709.
The register BNX2_CTX_STATUS (0x1004) should be skipped on 5709 as it
contains reserved bits.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Fri, 2 May 2008 23:56:44 +0000 (16:56 -0700)]
bnx2: Fix remote PHY initial link state.
On some remote PHY blade systems, the driver receives no initial link
interrupt. As a result, the GMII/MII MAC mode does not get setup properly.
To fix this problem, we add an initial poll of the link state after chip
reset.
With this change, the setting of the initial carrier state in the init
code can be eliminated.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan [Fri, 2 May 2008 23:56:16 +0000 (16:56 -0700)]
bnx2: Refine remote PHY locking.
bnx2_set_remote_link() should be called under bp->phy_lock to protect
against concurrent polling and interrupt calls. This change is needed
by the next patch which will add one initial poll of the remote PHY
link status.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Fri, 2 May 2008 23:53:33 +0000 (16:53 -0700)]
bridge: forwarding table information for >256 devices
The forwarding table binary interface (my bad choice), only exposes
the port number of the first 8 bits. The bridge code was limited to
256 ports at the time, but now the kernel supports up 1024 ports, so
the upper bits are lost when doing:
brctl showmacs
The fix is to squeeze the extra bits into small hole left in data
structure, to maintain binary compatiablity.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Fri, 2 May 2008 23:49:50 +0000 (16:49 -0700)]
tg3: Update version to 3.92
This patch updates the version number to 3.92.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Fri, 2 May 2008 23:49:29 +0000 (16:49 -0700)]
tg3: Add link state reporting to UMP firmware
All variants of the 5714, 5715, and 5780 offer a feature called the
"Universal Management Port". This feature is implemented in firmware
and is largely transparent to the driver, except...
It turns out that the UMP firmware needs to know the current status
of the link. Because the firmware cannot touch the PHY registers while
the driver is in control of the device, it needs the driver to report
link status changes through an additional handshaking mechanism.
Without this handshake, it has been observed in the field that the UMP
firmware will not operate correctly.
This patch implements the new handshake with the UMP firmware. Since
the handshake uses the same mechanism ASF heartbeats use, code was
added to detect and wait for completion of a pending previous event.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Carlson [Fri, 2 May 2008 23:48:59 +0000 (16:48 -0700)]
tg3: Fix ethtool loopback test for 5761 BX devices
A CPMU related loopback test bug existed for AX revisions of the 5761.
While that errata has been fixed, the CPMU still slows down the core
clock too far to run the loopback test successfully. This patch
disables the CPMU LINK_SPEED mode just like we do with the AX
revisions of the 5761 and all revisions of the 5784.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>