OSDN Git Service
Tom Herbert [Tue, 16 Mar 2010 08:03:29 +0000 (08:03 +0000)]
rps: Receive Packet Steering
This patch implements software receive side packet steering (RPS). RPS
distributes the load of received packet processing across multiple CPUs.
Problem statement: Protocol processing done in the NAPI context for received
packets is serialized per device queue and becomes a bottleneck under high
packet load. This substantially limits pps that can be achieved on a single
queue NIC and provides no scaling with multiple cores.
This solution queues packets early on in the receive path on the backlog queues
of other CPUs. This allows protocol processing (e.g. IP and TCP) to be
performed on packets in parallel. For each device (or each receive queue in
a multi-queue device) a mask of CPUs is set to indicate the CPUs that can
process packets. A CPU is selected on a per packet basis by hashing contents
of the packet header (e.g. the TCP or UDP 4-tuple) and using the result to index
into the CPU mask. The IPI mechanism is used to raise networking receive
softirqs between CPUs. This effectively emulates in software what a multi-queue
NIC can provide, but is generic requiring no device support.
Many devices now provide a hash over the 4-tuple on a per packet basis
(e.g. the Toeplitz hash). This patch allow drivers to set the HW reported hash
in an skb field, and that value in turn is used to index into the RPS maps.
Using the HW generated hash can avoid cache misses on the packet when
steering it to a remote CPU.
The CPU mask is set on a per device and per queue basis in the sysfs variable
/sys/class/net/<device>/queues/rx-<n>/rps_cpus. This is a set of canonical
bit maps for receive queues in the device (numbered by <n>). If a device
does not support multi-queue, a single variable is used for the device (rx-0).
Generally, we have found this technique increases pps capabilities of a single
queue device with good CPU utilization. Optimal settings for the CPU mask
seem to depend on architectures and cache hierarcy. Below are some results
running 500 instances of netperf TCP_RR test with 1 byte req. and resp.
Results show cumulative transaction rate and system CPU utilization.
e1000e on 8 core Intel
Without RPS: 108K tps at 33% CPU
With RPS: 311K tps at 64% CPU
forcedeth on 16 core AMD
Without RPS: 156K tps at 15% CPU
With RPS: 404K tps at 49% CPU
bnx2x on 16 core AMD
Without RPS 567K tps at 61% CPU (4 HW RX queues)
Without RPS 738K tps at 96% CPU (8 HW RX queues)
With RPS: 854K tps at 76% CPU (4 HW RX queues)
Caveats:
- The benefits of this patch are dependent on architecture and cache hierarchy.
Tuning the masks to get best performance is probably necessary.
- This patch adds overhead in the path for processing a single packet. In
a lightly loaded server this overhead may eliminate the advantages of
increased parallelism, and possibly cause some relative performance degradation.
We have found that masks that are cache aware (share same caches with
the interrupting CPU) mitigate much of this.
- The RPS masks can be changed dynamically, however whenever the mask is changed
this introduces the possibility of generating out of order packets. It's
probably best not change the masks too frequently.
Signed-off-by: Tom Herbert <therbert@google.com>
include/linux/netdevice.h | 32 ++++-
include/linux/skbuff.h | 3 +
net/core/dev.c | 335 +++++++++++++++++++++++++++++++++++++--------
net/core/net-sysfs.c | 225 ++++++++++++++++++++++++++++++-
net/core/skbuff.c | 2 +
5 files changed, 538 insertions(+), 59 deletions(-)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tina Yang [Thu, 11 Mar 2010 13:50:07 +0000 (13:50 +0000)]
RDS: Enable per-cpu workqueue threads
Create per-cpu workqueue threads instead of a single
krdsd thread. This is a step towards better scalability.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Grover [Thu, 11 Mar 2010 13:50:06 +0000 (13:50 +0000)]
RDS: Do not call set_page_dirty() with irqs off
set_page_dirty() unconditionally re-enables interrupts, so
if we call it with irqs off, they will be on after the call,
and that's bad. This patch moves the call after we've re-enabled
interrupts in send_drop_to(), so it's safe.
Also, add BUG_ONs to let us know if we ever do call set_page_dirty
with interrupts off.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sherman Pun [Thu, 11 Mar 2010 13:50:05 +0000 (13:50 +0000)]
RDS: Properly unmap when getting a remote access error
If the RDMA op has aborted with a remote access error,
in addition to what we already do (tell userspace it has
completed with an error) also unmap it and put() the rm.
Otherwise, hangs may occur on arches that track maps and
will not exit without proper cleanup.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Grover [Thu, 11 Mar 2010 13:50:04 +0000 (13:50 +0000)]
RDS: only put sockets that have seen congestion on the poll_waitq
rds_poll_waitq's listeners will be awoken if we receive a congestion
notification. Bad performance may result because *all* polled sockets
contend for this single lock. However, it should not be necessary to
wake pollers when a congestion update arrives if they have never
experienced congestion, and not putting these on the waitq will
hopefully greatly reduce contention.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tina Yang [Thu, 11 Mar 2010 13:50:03 +0000 (13:50 +0000)]
RDS: Fix locking in rds_send_drop_to()
It seems rds_send_drop_to() called
__rds_rdma_send_complete(rs, rm, RDS_RDMA_CANCELED)
with only rds_sock lock, but not rds_message lock. It raced with
other threads that is attempting to modify the rds_message as well,
such as from within rds_rdma_send_complete().
Signed-off-by: Tina Yang <tina.yang@oracle.com>
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Grover [Thu, 11 Mar 2010 13:50:02 +0000 (13:50 +0000)]
RDS: Turn down alarming reconnect messages
RDS's error messages when a connection goes down are a little
extreme. A connection may go down, and it will be re-established,
and everything is fine. This patch links these messages through
rdsdebug(), instead of to printk directly.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Grover [Thu, 11 Mar 2010 13:50:01 +0000 (13:50 +0000)]
RDS: Workaround for in-use MRs on close causing crash
if a machine is shut down without closing sockets properly, and
freeing all MRs, then a BUG_ON will bring it down. This patch
changes these to WARN_ONs -- leaking MRs is not fatal (although
not ideal, and there is more work to do here for a proper fix.)
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tina Yang [Thu, 11 Mar 2010 13:50:00 +0000 (13:50 +0000)]
RDS: Fix send locking issue
Fix a deadlock between rds_rdma_send_complete() and
rds_send_remove_from_sock() when rds socket lock and
rds message lock are acquired out-of-order.
Signed-off-by: Tina Yang <Tina.Yang@oracle.com>
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Grover [Thu, 11 Mar 2010 13:49:59 +0000 (13:49 +0000)]
RDS: Fix congestion issues for loopback
We have two kinds of loopback: software (via loop transport)
and hardware (via IB). sw is used for 127.0.0.1, and doesn't
support rdma ops. hw is used for sends to local device IPs,
and supports rdma. Both are used in different cases.
For both of these, when there is a congestion map update, we
want to call rds_cong_map_updated() but not actually send
anything -- since loopback local and foreign congestion maps
point to the same spot, they're already in sync.
The old code never called sw loop's xmit_cong_map(),so
rds_cong_map_updated() wasn't being called for it. sw loop
ports would not work right with the congestion monitor.
Fixing that meant that hw loopback now would send congestion maps
to itself. This is also undesirable (racy), so we check for this
case in the ib-specific xmit code.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Grover [Thu, 11 Mar 2010 13:49:58 +0000 (13:49 +0000)]
RDS/TCP: Wait to wake thread when write space available
Instead of waking the send thread whenever any send space is available,
wait until it is at least half empty. This is modeled on how
sock_def_write_space() does it, and may help to minimize context
switches.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Grover [Thu, 11 Mar 2010 13:49:57 +0000 (13:49 +0000)]
RDS: update copy_to_user state in tcp transport
Other transports use rds_page_copy_user, which updates our
s_copy_to_user counter. TCP doesn't, so it needs to explicity
call rds_stats_add().
Reported-by: Richard Frank <richard.frank@oracle.com>
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Grover [Thu, 11 Mar 2010 13:49:56 +0000 (13:49 +0000)]
RDS: sendmsg() should check sndtimeo, not rcvtimeo
Most likely cut n paste error - sendmsg() was checking sock_rcvtimeo.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Grover [Thu, 11 Mar 2010 13:49:55 +0000 (13:49 +0000)]
RDS: Do not BUG() on error returned from ib_post_send
BUGging on a runtime error code should be avoided. This
patch also eliminates all other BUG()s that have no real
reason to exist.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 16 Mar 2010 21:37:47 +0000 (14:37 -0700)]
bridge: Make first arg to deliver_clone const.
Otherwise we get a warning from the call in br_forward().
Signed-off-by: David S. Miller <davem@davemloft.net>
YOSHIFUJI Hideaki / 吉藤英明 [Mon, 15 Mar 2010 21:51:18 +0000 (21:51 +0000)]
bridge br_multicast: Don't refer to BR_INPUT_SKB_CB(skb)->mrouters_only without IGMP snooping.
Without CONFIG_BRIDGE_IGMP_SNOOPING,
BR_INPUT_SKB_CB(skb)->mrouters_only is not appropriately
initialized, so we can see garbage.
A clear option to fix this is to set it even without that
config, but we cannot optimize out the branch.
Let's introduce a macro that returns value of mrouters_only
and let it return 0 without CONFIG_BRIDGE_IGMP_SNOOPING.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vitaliy Gusev [Tue, 16 Mar 2010 01:07:51 +0000 (01:07 +0000)]
route: Fix caught BUG_ON during rt_secret_rebuild_oneshot()
route: Fix caught BUG_ON during rt_secret_rebuild_oneshot()
Call rt_secret_rebuild can cause BUG_ON(timer_pending(&net->ipv4.rt_secret_timer)) in
add_timer as there is not any synchronization for call rt_secret_rebuild_oneshot()
for the same net namespace.
Also this issue affects to rt_secret_reschedule().
Thus use mod_timer enstead.
Signed-off-by: Vitaliy Gusev <vgusev@openvz.org>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
YOSHIFUJI Hideaki / 吉藤英明 [Mon, 15 Mar 2010 19:26:56 +0000 (19:26 +0000)]
bridge br_multicast: Fix skb leakage in error path.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
YOSHIFUJI Hideaki / 吉藤英明 [Mon, 15 Mar 2010 19:27:00 +0000 (19:27 +0000)]
bridge br_multicast: Fix handling of Max Response Code in IGMPv3 message.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Slaby [Tue, 16 Mar 2010 05:29:54 +0000 (05:29 +0000)]
NET: netpoll, fix potential NULL ptr dereference
Stanse found that one error path in netpoll_setup dereferences npinfo
even though it is NULL. Avoid that by adding new label and go to that
instead.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Daniel Borkmann <danborkmann@googlemail.com>
Cc: David S. Miller <davem@davemloft.net>
Acked-by: chavey@google.com
Acked-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Neil Horman [Tue, 16 Mar 2010 08:14:33 +0000 (08:14 +0000)]
tipc: fix lockdep warning on address assignment
So in the forward porting of various tipc packages, I was constantly
getting this lockdep warning everytime I used tipc-config to set a network
address for the protocol:
[ INFO: possible circular locking dependency detected ]
2.6.33 #1
tipc-config/1326 is trying to acquire lock:
(ref_table_lock){+.-...}, at: [<
ffffffffa0315148>] tipc_ref_discard+0x53/0xd4 [tipc]
but task is already holding lock:
(&(&entry->lock)->rlock#2){+.-...}, at: [<
ffffffffa03150d5>] tipc_ref_lock+0x43/0x63 [tipc]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&(&entry->lock)->rlock#2){+.-...}:
[<
ffffffff8107b508>] __lock_acquire+0xb67/0xd0f
[<
ffffffff8107b78c>] lock_acquire+0xdc/0x102
[<
ffffffff8145471e>] _raw_spin_lock_bh+0x3b/0x6e
[<
ffffffffa03152b1>] tipc_ref_acquire+0xe8/0x11b [tipc]
[<
ffffffffa031433f>] tipc_createport_raw+0x78/0x1b9 [tipc]
[<
ffffffffa031450b>] tipc_createport+0x8b/0x125 [tipc]
[<
ffffffffa030f221>] tipc_subscr_start+0xce/0x126 [tipc]
[<
ffffffffa0308fb2>] process_signal_queue+0x47/0x7d [tipc]
[<
ffffffff81053e0c>] tasklet_action+0x8c/0xf4
[<
ffffffff81054bd8>] __do_softirq+0xf8/0x1cd
[<
ffffffff8100aadc>] call_softirq+0x1c/0x30
[<
ffffffff810549f4>] _local_bh_enable_ip+0xb8/0xd7
[<
ffffffff81054a21>] local_bh_enable_ip+0xe/0x10
[<
ffffffff81454d31>] _raw_spin_unlock_bh+0x34/0x39
[<
ffffffffa0308eb8>] spin_unlock_bh.clone.0+0x15/0x17 [tipc]
[<
ffffffffa0308f47>] tipc_k_signal+0x8d/0xb1 [tipc]
[<
ffffffffa0308dd9>] tipc_core_start+0x8a/0xad [tipc]
[<
ffffffffa01b1087>] 0xffffffffa01b1087
[<
ffffffff8100207d>] do_one_initcall+0x72/0x18a
[<
ffffffff810872fb>] sys_init_module+0xd8/0x23a
[<
ffffffff81009b42>] system_call_fastpath+0x16/0x1b
-> #0 (ref_table_lock){+.-...}:
[<
ffffffff8107b3b2>] __lock_acquire+0xa11/0xd0f
[<
ffffffff8107b78c>] lock_acquire+0xdc/0x102
[<
ffffffff81454836>] _raw_write_lock_bh+0x3b/0x6e
[<
ffffffffa0315148>] tipc_ref_discard+0x53/0xd4 [tipc]
[<
ffffffffa03141ee>] tipc_deleteport+0x40/0x119 [tipc]
[<
ffffffffa0316e35>] release+0xeb/0x137 [tipc]
[<
ffffffff8139dbf4>] sock_release+0x1f/0x6f
[<
ffffffff8139dc6b>] sock_close+0x27/0x2b
[<
ffffffff811116f6>] __fput+0x12a/0x1df
[<
ffffffff811117c5>] fput+0x1a/0x1c
[<
ffffffff8110e49b>] filp_close+0x68/0x72
[<
ffffffff8110e552>] sys_close+0xad/0xe7
[<
ffffffff81009b42>] system_call_fastpath+0x16/0x1b
Finally decided I should fix this. Its a straightforward inversion,
tipc_ref_acquire takes two locks in this order:
ref_table_lock
entry->lock
while tipc_deleteport takes them in this order:
entry->lock (via tipc_port_lock())
ref_table_lock (via tipc_ref_discard())
when the same entry is referenced, we get the above warning. The fix is equally
straightforward. Theres no real relation between the entry->lock and the
ref_table_lock (they just are needed at the same time), so move the entry->lock
aquisition in tipc_ref_acquire down, after we unlock ref_table_lock (this is
safe since the ref_table_lock guards changes to the reference table, and we've
already claimed a slot there. I've tested the below fix and confirmed that it
clears up the lockdep issue
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
James Chapman [Tue, 16 Mar 2010 06:29:20 +0000 (06:29 +0000)]
l2tp: Fix UDP socket reference count bugs in the pppol2tp driver
This patch fixes UDP socket refcnt bugs in the pppol2tp driver.
A bug can cause a kernel stack trace when a tunnel socket is closed.
A way to reproduce the issue is to prepare the UDP socket for L2TP (by
opening a tunnel pppol2tp socket) and then close it before any L2TP
sessions are added to it. The sequence is
Create UDP socket
Create tunnel pppol2tp socket to prepare UDP socket for L2TP
pppol2tp_connect: session_id=0, peer_session_id=0
L2TP SCCRP control frame received (tunnel_id==0)
pppol2tp_recv_core: sock_hold()
pppol2tp_recv_core: sock_put
L2TP ZLB control frame received (tunnel_id=nnn)
pppol2tp_recv_core: sock_hold()
pppol2tp_recv_core: sock_put
Close tunnel management socket
pppol2tp_release: session_id=0, peer_session_id=0
Close UDP socket
udp_lib_close: BUG
The addition of sock_hold() in pppol2tp_connect() solves the problem.
For data frames, two sock_put() calls were added to plug a refcnt leak
per received data frame. The ref that is grabbed at the top of
pppol2tp_recv_core() must always be released, but this wasn't done for
accepted data frames or data frames discarded because of bad UDP
checksums. This leak meant that any UDP socket that had passed L2TP
data traffic (i.e. L2TP data frames, not just L2TP control frames)
using pppol2tp would not be released by the kernel.
WARNING: at include/net/sock.h:435 udp_lib_unhash+0x117/0x120()
Pid: 1086, comm: openl2tpd Not tainted 2.6.33-rc1 #8
Call Trace:
[<
c119e9b7>] ? udp_lib_unhash+0x117/0x120
[<
c101b871>] ? warn_slowpath_common+0x71/0xd0
[<
c119e9b7>] ? udp_lib_unhash+0x117/0x120
[<
c101b8e3>] ? warn_slowpath_null+0x13/0x20
[<
c119e9b7>] ? udp_lib_unhash+0x117/0x120
[<
c11598a7>] ? sk_common_release+0x17/0x90
[<
c11a5e33>] ? inet_release+0x33/0x60
[<
c11577b0>] ? sock_release+0x10/0x60
[<
c115780f>] ? sock_close+0xf/0x30
[<
c106e542>] ? __fput+0x52/0x150
[<
c106b68e>] ? filp_close+0x3e/0x70
[<
c101d2e2>] ? put_files_struct+0x62/0xb0
[<
c101eaf7>] ? do_exit+0x5e7/0x650
[<
c1081623>] ? mntput_no_expire+0x13/0x70
[<
c106b68e>] ? filp_close+0x3e/0x70
[<
c101eb8a>] ? do_group_exit+0x2a/0x70
[<
c101ebe1>] ? sys_exit_group+0x11/0x20
[<
c10029b0>] ? sysenter_do_call+0x12/0x26
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steve Glendinning [Tue, 16 Mar 2010 09:03:06 +0000 (09:03 +0000)]
smsc95xx: wait for PHY to complete reset during init
This patch ensures the PHY correctly completes its reset before
setting register values.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
James Chapman [Tue, 16 Mar 2010 06:46:31 +0000 (06:46 +0000)]
l2tp: Fix oops in pppol2tp_xmit
When transmitting L2TP frames, we derive the outgoing interface's UDP
checksum hardware assist capabilities from the tunnel dst dev. This
can sometimes be NULL, especially when routing protocols are used and
routing changes occur. This patch just checks for NULL dst or dev
pointers when checking for netdev hardware assist features.
BUG: unable to handle kernel NULL pointer dereference at
0000000c
IP: [<
f89d074c>] pppol2tp_xmit+0x341/0x4da [pppol2tp]
*pde =
00000000
Oops: 0000 [#1] SMP
last sysfs file: /sys/class/net/lo/operstate
Modules linked in: pppol2tp pppox ppp_generic slhc ipv6 dummy loop snd_hda_codec_atihdmi snd_hda_intel snd_hda_codec snd_pcm snd_timer snd soundcore snd_page_alloc evdev psmouse serio_raw processor button i2c_piix4 i2c_core ati_agp agpgart pcspkr ext3 jbd mbcache sd_mod ide_pci_generic atiixp ide_core ahci ata_generic floppy ehci_hcd ohci_hcd libata e1000e scsi_mod usbcore nls_base thermal fan thermal_sys [last unloaded: scsi_wait_scan]
Pid: 0, comm: swapper Not tainted (2.6.32.8 #1)
EIP: 0060:[<
f89d074c>] EFLAGS:
00010297 CPU: 3
EIP is at pppol2tp_xmit+0x341/0x4da [pppol2tp]
EAX:
00000000 EBX:
f64d1680 ECX:
000005b9 EDX:
00000000
ESI:
f6b91850 EDI:
f64d16ac EBP:
f6a0c4c0 ESP:
f70a9cac
DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
Process swapper (pid: 0, ti=
f70a8000 task=
f70a31c0 task.ti=
f70a8000)
Stack:
000005a9 000005b9 f734c400 f66652c0 f7352e00 f67dc800 00000000 f6b91800
<0>
000005a3 f70ef6c4 f67dcda9 000005a3 f89b192e 00000246 000005a3 f64d1680
<0>
f63633e0 f6363320 f64d1680 f65a7320 f65a7364 f65856c0 f64d1680 f679f02f
Call Trace:
[<
f89b192e>] ? ppp_push+0x459/0x50e [ppp_generic]
[<
f89b217f>] ? ppp_xmit_process+0x3b6/0x430 [ppp_generic]
[<
f89b2306>] ? ppp_start_xmit+0x10d/0x120 [ppp_generic]
[<
c11c15cb>] ? dev_hard_start_xmit+0x21f/0x2b2
[<
c11d0947>] ? sch_direct_xmit+0x48/0x10e
[<
c11c19a0>] ? dev_queue_xmit+0x263/0x3a6
[<
c11e2a9f>] ? ip_finish_output+0x1f7/0x221
[<
c11df682>] ? ip_forward_finish+0x2e/0x30
[<
c11de645>] ? ip_rcv_finish+0x295/0x2a9
[<
c11c0b19>] ? netif_receive_skb+0x3e9/0x404
[<
f814b791>] ? e1000_clean_rx_irq+0x253/0x2fc [e1000e]
[<
f814cb7a>] ? e1000_clean+0x63/0x1fc [e1000e]
[<
c1047eff>] ? sched_clock_local+0x15/0x11b
[<
c11c1095>] ? net_rx_action+0x96/0x195
[<
c1035750>] ? __do_softirq+0xaa/0x151
[<
c1035828>] ? do_softirq+0x31/0x3c
[<
c10358fe>] ? irq_exit+0x26/0x58
[<
c1004b21>] ? do_IRQ+0x78/0x89
[<
c1003729>] ? common_interrupt+0x29/0x30
[<
c101ac28>] ? native_safe_halt+0x2/0x3
[<
c1008c54>] ? default_idle+0x55/0x75
[<
c1009045>] ? c1e_idle+0xd2/0xd5
[<
c100233c>] ? cpu_idle+0x46/0x62
Code: 8d 45 08 f0 ff 45 08 89 6b 08 c7 43 68 7e fb 9c f8 8a 45 24 83 e0 0c 3c 04 75 09 80 63 64 f3 e9 b4 00 00 00 8b 43 18 8b 4c 24 04 <8b> 40 0c 8d 79 11 f6 40 44 0e 8a 43 64 75 51 6a 00 8b 4c 24 08
EIP: [<
f89d074c>] pppol2tp_xmit+0x341/0x4da [pppol2tp] SS:ESP 0068:
f70a9cac
CR2:
000000000000000c
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steve Glendinning [Tue, 16 Mar 2010 08:46:46 +0000 (08:46 +0000)]
smsc75xx: SMSC LAN75xx USB gigabit ethernet adapter driver
This patch adds a driver for SMSC's LAN7500 family of USB 2.0
to gigabit ethernet adapters. It's loosely based on the smsc95xx
driver but the device registers for LAN7500 are completely different.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Atsushi Nemoto [Tue, 16 Mar 2010 05:27:40 +0000 (05:27 +0000)]
ne: Do not use slashes in irq name string
This patch fixes following warning introduced by commit
12bac0d9f4dbf3445a0319beee848d15fa32775e ("proc: warn on non-existing
proc entries"):
WARNING: at /work/mips-linux/make/linux/fs/proc/generic.c:316 __xlate_proc_name+0xe0/0xe8()
name 'RBHMA4X00/RTL8019'
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Slaby [Tue, 16 Mar 2010 04:53:50 +0000 (04:53 +0000)]
NET: ksz884x, fix lock imbalance
Stanse found that one error path (when alloc_skb fails) in netdev_tx
omits to unlock hw_priv->hwlock. Fix that.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Tristram Ha <Tristram.Ha@micrel.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tilman Schmidt [Tue, 16 Mar 2010 07:04:01 +0000 (07:04 +0000)]
gigaset: correct range checking off by one error
Correct a potential array overrun due to an off by one error in the
range check on the CAPI CONNECT_REQ CIPValue parameter.
Found and reported by Dan Carpenter using smatch.
Impact: bugfix
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Braun [Tue, 16 Mar 2010 07:26:22 +0000 (00:26 -0700)]
bridge: Fix br_forward crash in promiscuous mode
From: Michael Braun <michael-dev@fami-braun.de>
bridge: Fix br_forward crash in promiscuous mode
It's a linux-next kernel from 2010-03-12 on an x86 system and it
OOPs in the bridge module in br_pass_frame_up (called by
br_handle_frame_finish) because brdev cannot be dereferenced (its set to
a non-null value).
Adding some BUG_ON statements revealed that
BR_INPUT_SKB_CB(skb)->brdev == br-dev
(as set in br_handle_frame_finish first)
only holds until br_forward is called.
The next call to br_pass_frame_up then fails.
Digging deeper it seems that br_forward either frees the skb or passes
it to NF_HOOK which will in turn take care of freeing the skb. The
same is holds for br_pass_frame_ip. So it seems as if two independent
skb allocations are required. As far as I can see, commit
b33084be192ee1e347d98bb5c9e38a53d98d35e2 ("bridge: Avoid unnecessary
clone on forward path") removed skb duplication and so likely causes
this crash. This crash does not happen on 2.6.33.
I've therefore modified br_forward the same way br_flood has been
modified so that the skb is not freed if skb0 is going to be used
and I can confirm that the attached patch resolves the issue for me.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Tue, 16 Mar 2010 03:38:25 +0000 (20:38 -0700)]
bridge: Move NULL mdb check into br_mdb_ip_get
Since all callers of br_mdb_ip_get need to check whether the
hash table is NULL, this patch moves the check into the function.
This fixes the two callers (query/leave handler) that didn't
check it.
Reported-by: Michael Braun <michael-dev@fami-braun.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lars Ellenberg [Tue, 16 Mar 2010 02:09:28 +0000 (19:09 -0700)]
ISDN: Add PCI ID for HFC-2S/4S Beronet Card PCIe
A few subdevice IDs seem to have been dropped when hfc_multi was
included upstream, just compare the list at
http://www.openvox.cn/viewvc/misdn/trunk/hfc_multi.c?revision=75&view=annotate#l175
with the IDs in drivers/isdn/hardware/mISDN/hfcmulti.c
Added PCIe 2 Port card and LED settings (same as PCI)
Do not use <linux/pci_ids.h> /KKe
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 15 Mar 2010 23:23:54 +0000 (16:23 -0700)]
Merge branch 'master' of /home/davem/src/GIT/linux-2.6/
Gerrit Renker [Sun, 14 Mar 2010 20:13:19 +0000 (20:13 +0000)]
net-2.6 [Bug-Fix][dccp]: fix oops caused after failed initialisation
dccp: fix panic caused by failed initialisation
This fixes a kernel panic reported thanks to Andre Noll:
if DCCP is compiled into the kernel and any out of the initialisation
steps in net/dccp/proto.c:dccp_init() fail, a subsequent attempt to create
a SOCK_DCCP socket will panic, since inet{,6}_create() are not prevented
from creating DCCP sockets.
This patch fixes the problem by propagating a failure in dccp_init() to
dccp_v{4,6}_init_net(), and from there to dccp_v{4,6}_init(), so that the
DCCP protocol is not made available if its initialisation fails.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Sun, 14 Mar 2010 22:24:08 +0000 (22:24 +0000)]
myri: remove dead code
We can never reach the return statement.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tilman Schmidt [Sun, 14 Mar 2010 12:58:05 +0000 (12:58 +0000)]
gigaset: prune use of tty_buffer_request_room
Calling tty_buffer_request_room() before tty_insert_flip_string()
is unnecessary, costs CPU and for big buffers can mess up the
multi-page allocation avoidance.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Acked-by: Karsten Keil <keil@b1-systems.de>
CC: Alan Cox <alan@lxorguk.ukuu.org.uk>, stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Tilman Schmidt [Sun, 14 Mar 2010 12:58:05 +0000 (12:58 +0000)]
gigaset: correct clearing of at_state strings on RING
In RING handling, clear the table of received parameter strings in
a loop like everywhere else, instead of by enumeration which had
already gotten out of sync.
Impact: minor bugfix
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Acked-by: Karsten Keil <keil@b1-systems.de>
CC: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Tilman Schmidt [Sun, 14 Mar 2010 12:58:05 +0000 (12:58 +0000)]
gigaset: avoid registering CAPI driver more than once
Registering/unregistering the Gigaset CAPI driver when a device is
connected/disconnected causes an Oops when disconnecting two Gigaset
devices in a row, because the same capi_driver structure gets
unregistered twice. Fix by making driver registration/unregistration
a separate operation (empty in the ISDN4Linux case) called when the
main module is loaded/unloaded.
Impact: bugfix
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Acked-by: Karsten Keil <keil@b1-systems.de>
CC: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Christoph Egger [Thu, 11 Mar 2010 12:07:54 +0000 (12:07 +0000)]
obsolete config in kernel source: HSO_AUTOPM
CONFIG_HSO_AUTOPM is set by KConfig / set in the Kernel source, makefiles
and won't be ever set this way, therefor simply removing the protected
code.
Signed-off-by: Christoph Egger <siccegge@stud.informatik.uni-erlangen.de>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christoph Egger [Thu, 11 Mar 2010 12:07:52 +0000 (12:07 +0000)]
obsolete config in kernel source: USE_INTERNAL_TIMER
CONFIG_USE_INTERNAL_TIMER seems to be the remainings of some experiment.
It is explicitely #undef-ed as not working, only referenced from one
source file and rather aged.
Hereby cleaning it from the kernel tree.
Signed-off-by: Christoph Egger <siccegge@stud.informatik.uni-erlangen.de>
Acked-by: Roel Kluin <roel.kluin@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Akinobu Mita [Thu, 11 Mar 2010 12:07:50 +0000 (12:07 +0000)]
atm: use for_each_set_bit()
Replace open-coded loop with for_each_set_bit().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Akinobu Mita [Thu, 11 Mar 2010 12:07:49 +0000 (12:07 +0000)]
phonet: use for_each_set_bit()
Replace open-coded loop with for_each_set_bit().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Randy Dunlap [Fri, 12 Mar 2010 19:23:27 +0000 (19:23 +0000)]
timestamping: fix example build
Fix Makefiles so that Documentation/networking/timestamping/timestamping.c
will build when using the CONFIG_BUILD_DOCSRC kconfig option.
(timestamping.c does not build currently with its simple Makefile.)
Also fix printf format warnings.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Patrick Ohly <patrick.ohly@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Julia Lawall [Tue, 9 Mar 2010 11:14:11 +0000 (11:14 +0000)]
drivers/net: drop redundant memset
The region set by the call to memset is immediately overwritten by the
subsequent call to memcpy.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e1,e2,e3,e4;
@@
- memset(e1,e2,e3);
memcpy(e1,e4,e3);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ian Munsie [Thu, 11 Mar 2010 12:07:25 +0000 (12:07 +0000)]
i4l: change magic numbers in Eicon DIVA ISDN driver to symbolic names
Replace references to the '20' magic number found throughout the Eicon
ISDN driver for the length of the station_id field in the T30_INFO struct
with the T30_MAX_STATION_ID_LENGTH symbolic constant.
Signed-off-by: Ian Munsie <imunsie@au.ibm.com>
Cc: Armin Schindler <mac@melware.de>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Stoyan Gaydarov <sgayda2@uiuc.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ian Munsie [Thu, 11 Mar 2010 12:07:24 +0000 (12:07 +0000)]
i4l: silence compiler warnings for array access in Eicon DIVA ISDN driver
When compiling this driver, the compiler throws the following warnings:
drivers/isdn/hardware/eicon/message.c:8426: warning: array subscript is above array bounds
drivers/isdn/hardware/eicon/message.c:8427: warning: array subscript is above array bounds
drivers/isdn/hardware/eicon/message.c:8434: warning: array subscript is above array bounds
drivers/isdn/hardware/eicon/message.c:8435: warning: array subscript is above array bounds
drivers/isdn/hardware/eicon/message.c:8436: warning: array subscript is above array bounds
drivers/isdn/hardware/eicon/message.c:8447: warning: array subscript is above array bounds
This arises from the particular semantics the driver is using to write to
the nlc array (static byte[256]). The array has a length in byte 0
followed by a T30_INFO struct starting at byte 1.
The T30_INFO struct has a number of variable length strings after the
station_id entry, which cannot be explicitly defined in the struct and the
driver accesses them with an array index to station_id beyond the length
of station_id.
This patch merely changes the semantics that the driver uses to access the
entries after the station_id entry to use the original 256 byte nlc array
taking the offset and length of the station_id entry to calculate where to
write in the array, thereby silencing the warning.
Signed-off-by: Ian Munsie <imunsie@au.ibm.com>
Cc: Armin Schindler <mac@melware.de>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Stoyan Gaydarov <sgayda2@uiuc.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Roel Kluin [Thu, 11 Mar 2010 12:07:22 +0000 (12:07 +0000)]
isdn: misplaced parenthesis in pof_handle_data()
The parenthesis was misplaced.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Karsten Keil <isdn@linux-pingi.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stanislaw Gruszka [Tue, 9 Mar 2010 06:55:02 +0000 (06:55 +0000)]
bnx2x: change smp_mb() comment to conform the true
Access to fp->tx_bp_prod is protected by __netif_tx_lock,
smp_mb() is not needed for that.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stanislaw Gruszka [Tue, 9 Mar 2010 06:55:01 +0000 (06:55 +0000)]
bnx2x: remove not necessary compiler barrier
Access to fp->tx_bd_prod is protected by __netif_tx_lock, so we do not
need any barrier for that.
Update of fp->tx_bd_cons in bnx2x_tx_int() is not protected by lock, but
barrier() nor smb_mb() in bnx2x_tx_avail() not guarantee we will see
values that is written on other cpu. Ordering issues between
netif_tx_stop_queue(), netif_tx_queue_stopped(), fp->tx_bd_cons = bd_cons
and bnx2x_tx_avail() are already handled by smp_mb() in bnx2x_tx_int()
and bnx2x_start_xmit().
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stanislaw Gruszka [Tue, 9 Mar 2010 06:55:00 +0000 (06:55 +0000)]
bnx2x: use smp_mb() to keep ordering of read write operations
Since we want to keep ordering of write to fp->bd_tx_cons and
netif_tx_queue_stopped(txq), what is read of txq->state, we have to use
general memory barrier.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ajit Khaparde [Thu, 11 Mar 2010 01:35:59 +0000 (01:35 +0000)]
be2net: fix mccq create for big endian architectures
The request to create an mccq was being dispatched without
doing a byte swap of num_pages. This byte swap is necessary
for Big Endian systems like PPC. Not having this fix leads
mccq create to fail on BE ASICs running newer version of
firmware, thereby causing driver initialization failure.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
chaithrika@ti.com [Wed, 10 Mar 2010 22:37:56 +0000 (22:37 +0000)]
TI DaVinci EMAC: Convert to dev_pm_ops
Migrate from the legacy PM hooks to use dev_pm_ops structure.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sekhar Nori [Tue, 9 Mar 2010 01:20:37 +0000 (01:20 +0000)]
net: davinci emac: use dma_{map, unmap}_single API for cache coherency
The davinci emac driver uses some ARM specific DMA APIs
for cache coherency which have been removed from kernel
with the 2.6.34 merge.
Modify the driver to use the dma_{map, unmap}_single() APIs
defined in dma-mapping.h
Without this fix, the driver fails to compile on Linus's
tree.
Tested on DM365 and OMAP-L138 EVMs.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 15 Mar 2010 22:23:30 +0000 (15:23 -0700)]
e100: Fix ring parameter change handling regression.
When the PCI pool changes were added to fix resume failures:
commit
98468efddb101f8a29af974101c17ba513b07be1
e100: Use pci pool to work around GFP_ATOMIC order 5 memory allocation failu
and
commit
70abc8cb90e679d8519721e2761d8366a18212a6
e100: Fix broken cbs accounting due to missing memset.
This introduced a problem that can happen if the TX ring size
is increased. We need to size the PCI pool using cbs->max
instead of the default cbs->count value.
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 15 Mar 2010 03:29:21 +0000 (20:29 -0700)]
Merge branch 'release' of git://git./linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (34 commits)
ACPI: processor: push file static MADT pointer into internal map_madt_entry()
ACPI: processor: refactor internal map_lsapic_id()
ACPI: processor: refactor internal map_x2apic_id()
ACPI: processor: refactor internal map_lapic_id()
ACPI: processor: driver doesn't need to evaluate _PDC
ACPI: processor: remove early _PDC optin quirks
ACPI: processor: add internal processor_physically_present()
ACPI: processor: move acpi_get_cpuid into processor_core.c
ACPI: processor: export acpi_get_cpuid()
ACPI: processor: mv processor_pdc.c processor_core.c
ACPI: processor: mv processor_core.c processor_driver.c
ACPI: plan to delete "acpi=ht" boot option
ACPI: remove "acpi=ht" DMI blacklist
PNPACPI: add bus number support
PNPACPI: add window support
resource: add window support
resource: add bus number support
resource: expand IORESOURCE_TYPE_BITS to make room for bus resource type
acpiphp: Execute ACPI _REG method for hotadded devices
ACPI video: Be more liberal in validating _BQC behaviour
...
Wolfram Sang [Mon, 15 Mar 2010 00:29:41 +0000 (01:29 +0100)]
init dynamic bin_attribute structures
Commit
6992f5334995af474c2b58d010d08bc597f0f2fe ("sysfs: Use one lockdep
class per sysfs attribute.") introduced this requirement. First, at25
was fixed manually. Then, other occurences were found with coccinelle
and the following semantic patch. Results were reviewed and fixed up:
@ init @
identifier struct_name, bin;
@@
struct struct_name {
...
struct bin_attribute bin;
...
};
@ main extends init @
expression E;
statement S;
identifier name, err;
@@
(
struct struct_name *name;
|
- struct struct_name *name = NULL;
+ struct struct_name *name;
)
...
(
sysfs_bin_attr_init(&name->bin);
|
+ sysfs_bin_attr_init(&name->bin);
if (sysfs_create_bin_file(E, &name->bin))
S
|
+ sysfs_bin_attr_init(&name->bin);
err = sysfs_create_bin_file(E, &name->bin);
)
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Len Brown [Mon, 15 Mar 2010 01:30:17 +0000 (21:30 -0400)]
Merge branches 'battery-2.6.34', 'bugzilla-10805', 'bugzilla-14668', 'bugzilla-531916-power-state', 'ht-warn-2.6.34', 'pnp', 'processor-rename', 'sony-2.6.34', 'suse-bugzilla-531547', 'tz-check', 'video' and 'misc-2.6.34' into release
Alex Chiang [Mon, 22 Feb 2010 19:12:00 +0000 (12:12 -0700)]
ACPI: processor: push file static MADT pointer into internal map_madt_entry()
There's no real need for a pointer to the MADT to be global. The only
function who uses it is map_madt_entry.
This allows us to remove some more ugly #ifdefs.
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Alex Chiang [Mon, 22 Feb 2010 19:11:55 +0000 (12:11 -0700)]
ACPI: processor: refactor internal map_lsapic_id()
Un-nest the if statements for readability.
Remove comments that re-state the obvious.
Change the control flow so that we no longer need a temp variable.
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Alex Chiang [Mon, 22 Feb 2010 19:11:50 +0000 (12:11 -0700)]
ACPI: processor: refactor internal map_x2apic_id()
Untangle the nested if conditions to make this function look
more similar to the other map_*apic_id() functions.
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Alex Chiang [Mon, 22 Feb 2010 19:11:44 +0000 (12:11 -0700)]
ACPI: processor: refactor internal map_lapic_id()
Untangle the if() statement a little for readability.
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Alex Chiang [Mon, 22 Feb 2010 19:11:39 +0000 (12:11 -0700)]
ACPI: processor: driver doesn't need to evaluate _PDC
Now that the early _PDC evaluation path knows how to correctly
evaluate _PDC on only physically present processors, there's no
need for the processor driver to evaluate it later when it loads.
To cover the hotplug case, push _PDC evaluation down into the
hotplug paths.
Cc: x86@kernel.org
Cc: Tony Luck <tony.luck@intel.com>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Alex Chiang [Mon, 22 Feb 2010 19:11:34 +0000 (12:11 -0700)]
ACPI: processor: remove early _PDC optin quirks
Now that we check for physically present processors before blindly
evaluating _PDC, we no longer need to maintain a DMI opt-in table
nor a kernel param.
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Alex Chiang [Mon, 22 Feb 2010 19:11:29 +0000 (12:11 -0700)]
ACPI: processor: add internal processor_physically_present()
Detect if a processor is physically present before evaluating _PDC.
We want this because some BIOS will provide a _PDC even for processors
that are not present. These bogus _PDC methods then attempt to load
non-existent tables, which causes problems.
Avoid those bogus landmines.
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Alex Chiang [Mon, 22 Feb 2010 19:11:24 +0000 (12:11 -0700)]
ACPI: processor: move acpi_get_cpuid into processor_core.c
Enumerating processors (via MADT/_MAT) belongs in the processor core,
which is always built-in, rather than living in the processor driver
which may not be built.
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Alex Chiang [Mon, 22 Feb 2010 19:11:19 +0000 (12:11 -0700)]
ACPI: processor: export acpi_get_cpuid()
Rename static get_cpu_id() to acpi_get_cpuid() and export it.
This change also gives us an opportunity to remove the
#ifndef CONFIG_SMP from processor_driver.c and into a header file
where it properly belongs.
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Alex Chiang [Mon, 22 Feb 2010 19:11:14 +0000 (12:11 -0700)]
ACPI: processor: mv processor_pdc.c processor_core.c
We've renamed the old processor_core.c to processor_driver.c, to
convey the idea that it can be built modular and has driver-like
bits.
Now let's re-create a processor_core.c for the bits needed
statically by the rest of the kernel. The contents of processor_pdc.c
are a good starting spot, so let's just rename that file and
complete our three card monte.
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Alex Chiang [Mon, 22 Feb 2010 19:11:08 +0000 (12:11 -0700)]
ACPI: processor: mv processor_core.c processor_driver.c
The ACPI processor driver can be built as a module. But it has
pieces of code that should always be built statically into the
kernel.
The plan is for processor_core.c to contain the static bits while
processor_driver.c contains the module-like bits.
Since the bulk of the code in the current processor_core.c is
module-like, first step is to rename the file to processor_driver.c
Next step will re-create processor_core.c and cherry-pick out
the static bits.
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Len Brown [Sun, 14 Mar 2010 20:28:46 +0000 (16:28 -0400)]
ACPI: plan to delete "acpi=ht" boot option
Signed-off-by: Len Brown <len.brown@intel.com>
Len Brown [Fri, 19 Feb 2010 04:42:47 +0000 (23:42 -0500)]
ACPI: remove "acpi=ht" DMI blacklist
SuSE added these entries when deploying ACPI in Linux-2.4.
I pulled them into Linux-2.6 on 2003-08-09.
Over the last 6+ years, several entries have proven to be
unnecessary and deleted, while no new entries have been added.
Matthew suggests that they now have negative value, and I agree.
Based-on-patch-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Bjorn Helgaas [Fri, 5 Mar 2010 17:47:57 +0000 (10:47 -0700)]
PNPACPI: add bus number support
Add support for bus number resources. This is for bridges with a range of
bus numbers behind them. Previously, PNP ignored bus number resources.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Bjorn Helgaas [Fri, 5 Mar 2010 17:47:52 +0000 (10:47 -0700)]
PNPACPI: add window support
Add support for resource windows. This is for bridge resources, i.e.,
regions where a bridge forwards transactions from the primary to the
secondary side. This does not add support for *setting* windows via
the /proc interface.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Bjorn Helgaas [Fri, 5 Mar 2010 17:47:47 +0000 (10:47 -0700)]
resource: add window support
Add support for resource windows. This is for bridge resources, i.e.,
regions where a bridge forwards transactions from the primary to the
secondary side.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Bjorn Helgaas [Fri, 5 Mar 2010 17:47:42 +0000 (10:47 -0700)]
resource: add bus number support
Add support for bus number resources. This is for bridges with a range of
bus numbers behind them.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Bjorn Helgaas [Fri, 5 Mar 2010 17:47:26 +0000 (10:47 -0700)]
resource: expand IORESOURCE_TYPE_BITS to make room for bus resource type
No functional change; this just makes room for another resource type.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Dan Carpenter [Sat, 13 Mar 2010 11:14:22 +0000 (14:14 +0300)]
tomoyo: fix potential use after free
The original code returns a freed pointer. This function is expected to
return NULL on errors.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: James Morris <jmorris@namei.org>
Shaohua Li [Thu, 25 Feb 2010 02:59:34 +0000 (10:59 +0800)]
acpiphp: Execute ACPI _REG method for hotadded devices
Per ACPI spec, _ERG method should be executed before device driver
gets control for hotpluged device. Firmware might do some configuration
there. See http://bugzilla.kernel.org/show_bug.cgi?id=10805. In this
machine, _REG method of docked device will configure cardbus bridge.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Tested-by: Paul Martin <pm@debian.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Matthew Garrett [Tue, 16 Feb 2010 21:53:50 +0000 (16:53 -0500)]
ACPI video: Be more liberal in validating _BQC behaviour
Right now, if _BQC returns a value we don't understand we immediately
invalidate it. Change this behaviour so we only invalidate it if it
continues to give an invalid answer after we've already set a brightness.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Linus Torvalds [Sun, 14 Mar 2010 18:15:45 +0000 (11:15 -0700)]
Merge branch 'core-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86/mce: Fix build bug with CONFIG_PROVE_LOCKING=y && CONFIG_X86_MCE_INTEL=y
Randy Dunlap [Thu, 4 Feb 2010 20:11:09 +0000 (12:11 -0800)]
Add include to i2c-xii.c to fix build error
drivers/i2c/busses/i2c-xiic.c:493: error: implicit declaration of function 'mdelay'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: "Richard Röjfors" <richard.rojfors@pelagicore.com>
Cc: "Ben Dooks (embedded platforms)" <ben-linux@fluff.org>
Cc: linux-i2c@vger.kernel.org
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Richard Röjfors [Tue, 9 Mar 2010 08:17:36 +0000 (09:17 +0100)]
Add the platform data include for the Xilinx XPS IIC Bus Interface
This file was missed in the original patch that went into Linus' tree.
Cc: "Ben Dooks (embedded platforms)" <ben-linux@fluff.org>
Cc: linux-i2c@vger.kernel.org
Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 14 Mar 2010 18:13:54 +0000 (11:13 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: i8042 - add ALDI/MEDION netbook E1222 to qurik reset table
Input: ALPS - fix stuck buttons on some touchpads
Input: wm831x-on - convert to use genirq
Input: ads7846 - add wakeup support
Input: appletouch - fix integer overflow issue
Input: ad7877 - increase pen up imeout
Input: ads7846 - add support for AD7843 parts
Input: bf54x-keys - fix system hang when pressing a key
Input: alps - add support for the touchpad on Toshiba Tecra A11-11L
Input: remove BKL, fix input_open_file() locking
Input: serio_raw - remove BKL
Input: mousedev - remove BKL
Input: add driver for TWL4030 vibrator device
Input: enable remote wakeup for PNP i8042 keyboard ports
Input: scancode in get/set_keycodes should be unsigned
Input: i8042 - use platfrom_create_bundle() helper
Input: wacom - merge out and in prox events
Input: gamecon - fix off by one range check
Input: wacom - replace WACOM_PKGLEN_PENABLED
Linus Torvalds [Sun, 14 Mar 2010 18:13:24 +0000 (11:13 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/ryusuke/nilfs2
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ryusuke/nilfs2:
nilfs2: remove whitespaces before quoted newlines
nilfs2: remove spaces before tabs
nilfs2: fix various typos in comments
nilfs2: fix typo "cout" -> "count" in error message
nilfs2: fix function name typos in docbook comments
nilfs2: fix discrepancy in use of static specifier
Linus Torvalds [Sun, 14 Mar 2010 18:13:04 +0000 (11:13 -0700)]
Merge branch 'i2c-for-linus' of git://git./linux/kernel/git/jdelvare/staging
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
i2c-algo-bit: Add pre- and post-xfer hooks
at24: Init dynamic bin_attribute structures
i2c: Drop configure option I2C_DEBUG_CHIP
tsl2550: Move from i2c/chips to misc
i2c-i801: Don't use the block buffer for I2C block writes
i2c-powermac: Be less verbose in the absence of real errors.
i2c-smbus: Use device_lock/device_unlock
Linus Torvalds [Sun, 14 Mar 2010 18:11:08 +0000 (11:11 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/ericvh/v9fs
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
9p: Skip check for mandatory locks when unlocking
9p: Fixes a simple bug enabling writes beyond 2GB.
9p: Change the name of new protocol from 9p2010.L to 9p2000.L
fs/9p: re-init the wstat in readdir loop
net/9p: Add sysfs mount_tag file for virtio 9P device
net/9p: Use the tag name in the config space for identifying mount point
Ingo Molnar [Sun, 14 Mar 2010 07:57:03 +0000 (08:57 +0100)]
x86/mce: Fix build bug with CONFIG_PROVE_LOCKING=y && CONFIG_X86_MCE_INTEL=y
Commit
f56e8a076 "x86/mce: Fix RCU lockdep splats" introduced the
following build bug:
arch/x86/kernel/cpu/mcheck/mce.c: In function 'mce_log':
arch/x86/kernel/cpu/mcheck/mce.c:166: error: 'mce_read_mutex' undeclared (first use in this function)
arch/x86/kernel/cpu/mcheck/mce.c:166: error: (Each undeclared identifier is reported only once
arch/x86/kernel/cpu/mcheck/mce.c:166: error: for each function it appears in.)
Move the in-the-middle-of-file lock variable up to the variable
definition section, the top of the .c file.
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: x86@kernel.org
Cc: laijs@cn.fujitsu.com
Cc: dipankar@in.ibm.com
Cc: mathieu.desnoyers@polymtl.ca
Cc: josh@joshtriplett.org
Cc: dvhltc@us.ibm.com
Cc: niv@us.ibm.com
Cc: peterz@infradead.org
Cc: rostedt@goodmis.org
Cc: Valdis.Kletnieks@vt.edu
Cc: dhowells@redhat.com
LKML-Reference: <
1267830207-9474-3-git-send-email-paulmck@linux.vnet.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Christoph Fritz [Sun, 14 Mar 2010 06:26:23 +0000 (22:26 -0800)]
Input: i8042 - add ALDI/MEDION netbook E1222 to qurik reset table
ALDI/MEDION netbook E1222 needs to be in the reset quirk list for
its touchpad's proper function.
Reported-by: Michael Fischer <mifi@gmx.de>
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Cc: stable@kernel.org
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Martin Buck [Sun, 14 Mar 2010 06:23:58 +0000 (22:23 -0800)]
Input: ALPS - fix stuck buttons on some touchpads
Enable button release event redirection to the device that got the
button press not only for touchpads with interleaved protocols, but
unconditionally for all Alps touchpads. This is required at least
for the touchpads in Dell Inspiron 8200 and Latitude d630.
Signed-off-by: Martin Buck <mb-tmp-yvahk-vachg@gromit.dyndns.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Linus Torvalds [Sun, 14 Mar 2010 05:29:38 +0000 (21:29 -0800)]
Merge git://git./linux/kernel/git/davem/sparc-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc64: Add very basic XVR-1000 framebuffer driver.
qlogicpti: Remove slash in QlogicPTI irq name
Ryusuke Konishi [Sat, 13 Mar 2010 19:01:27 +0000 (04:01 +0900)]
nilfs2: remove whitespaces before quoted newlines
This kills the following checkpatch warnings:
WARNING: unnecessary whitespace before a quoted newline
#869: FILE: super.c:869:
+ "remount to a different snapshot. \n",
WARNING: unnecessary whitespace before a quoted newline
#389: FILE: the_nilfs.c:389:
+ printk(KERN_ERR "NILFS: too short segment. \n");
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Ryusuke Konishi [Sat, 13 Mar 2010 18:55:56 +0000 (03:55 +0900)]
nilfs2: remove spaces before tabs
This kills the following checkpatch warnings:
WARNING: please, no space before tabs
#74: FILE: segment.h:74:
+^Iunsigned ^I^Iflags;$
WARNING: please, no space before tabs
#35: FILE: segbuf.c:35:
+^Iint ^I^I^Istart, end; /* The region to be submitted */$
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Ryusuke Konishi [Sat, 13 Mar 2010 18:32:40 +0000 (03:32 +0900)]
nilfs2: fix various typos in comments
This fixes various typos I found in comments of nilfs2.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Ryusuke Konishi [Sat, 13 Mar 2010 18:17:45 +0000 (03:17 +0900)]
nilfs2: fix typo "cout" -> "count" in error message
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Ryusuke Konishi [Sat, 13 Mar 2010 18:01:03 +0000 (03:01 +0900)]
nilfs2: fix function name typos in docbook comments
Fixes the following typos in docbook comments:
nilfs_detroy_transaction_cache -> nilfs_destroy_transaction_cache
nilfs_secgtor_start_timer -> nilfs_segctor_start_timer
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Ryusuke Konishi [Sat, 13 Mar 2010 17:01:51 +0000 (02:01 +0900)]
nilfs2: fix discrepancy in use of static specifier
Two segbuf functions, nilfs_segbuf_write and nilfs_segbuf_wait, are
declared with the static storage class specifier, but their
implementations are not.
This fixes the discrepancy.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
David S. Miller [Sun, 14 Mar 2010 00:25:03 +0000 (16:25 -0800)]
sparc64: Add very basic XVR-1000 framebuffer driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Frans van Berckel <fberckel@xs4all.nl>
Linus Torvalds [Sat, 13 Mar 2010 22:50:18 +0000 (14:50 -0800)]
Merge git://git./linux/kernel/git/davem/net-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (108 commits)
bridge: ensure to unlock in error path in br_multicast_query().
drivers/net/tulip/eeprom.c: fix bogus "(null)" in tulip init messages
sky2: Avoid rtnl_unlock without rtnl_lock
ipv6: Send netlink notification when DAD fails
drivers/net/tg3.c: change the field used with the TG3_FLAG_10_100_ONLY constant
ipconfig: Handle devices which take some time to come up.
mac80211: Fix memory leak in ieee80211_if_write()
mac80211: Fix (dynamic) power save entry
ipw2200: use kmalloc for large local variables
ath5k: read eeprom IQ calibration values correctly for G mode
ath5k: fix I/Q calibration (for real)
ath5k: fix TSF reset
ath5k: use fixed antenna for tx descriptors
libipw: split ieee->networks into small pieces
mac80211: Fix sta_mtx unlocking on insert STA failure path
rt2x00: remove KSEG1ADDR define from rt2x00soc.h
net: add ColdFire support to the smc91x driver
asix: fix setting mac address for AX88772
ipv6 ip6_tunnel: eliminate unused recursion field from ip6_tnl{}.
net: Fix dev_mc_add()
...
Linus Torvalds [Sat, 13 Mar 2010 22:46:18 +0000 (14:46 -0800)]
Merge branch 'sched-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Fix pick_next_highest_task_rt() for cgroups
sched: Cleanup: remove unused variable in try_to_wake_up()
x86: Fix sched_clock_cpu for systems with unsynchronized TSC
Linus Torvalds [Sat, 13 Mar 2010 22:45:49 +0000 (14:45 -0800)]
Merge branch 'x86-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, k8 nb: Fix boot crash: enable k8_northbridges unconditionally on AMD systems
x86, UV: Fix target_cpus() in x2apic_uv_x.c
x86: Reduce per cpu warning boot up messages
x86: Reduce per cpu MCA boot up messages
x86_64, cpa: Don't work hard in preserving kernel 2M mappings when using 4K already
Linus Torvalds [Sat, 13 Mar 2010 22:43:01 +0000 (14:43 -0800)]
Merge branch 'core-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
locking: Make sparse work with inline spinlocks and rwlocks
x86/mce: Fix RCU lockdep splats
rcu: Increase RCU CPU stall timeouts if PROVE_RCU
ftrace: Replace read_barrier_depends() with rcu_dereference_raw()
rcu: Suppress RCU lockdep warnings during early boot
rcu, ftrace: Fix RCU lockdep splat in ftrace_perf_buf_prepare()
rcu: Suppress __mpol_dup() false positive from RCU lockdep
rcu: Make rcu_read_lock_sched_held() handle !PREEMPT
rcu: Add control variables to lockdep_rcu_dereference() diagnostics
rcu, cgroup: Relax the check in task_subsys_state() as early boot is now handled by lockdep-RCU
rcu: Use wrapper function instead of exporting tasklist_lock
sched, rcu: Fix rcu_dereference() for RCU-lockdep
rcu: Make task_subsys_state() RCU-lockdep checks handle boot-time use
rcu: Fix holdoff for accelerated GPs for last non-dynticked CPU
x86/gart: Unexport gart_iommu_aperture
Fix trivial conflicts in kernel/trace/ftrace.c
Linus Torvalds [Sat, 13 Mar 2010 22:40:50 +0000 (14:40 -0800)]
Merge branch 'tracing-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
tracing: Do not record user stack trace from NMI context
tracing: Disable buffer switching when starting or stopping trace
tracing: Use same local variable when resetting the ring buffer
function-graph: Init curr_ret_stack with ret_stack
ring-buffer: Move disabled check into preempt disable section
function-graph: Add tracing_thresh support to function_graph tracer
tracing: Update the comm field in the right variable in update_max_tr
function-graph: Use comment notation for func names of dangling '}'
function-graph: Fix unused reference to ftrace_set_func()
tracing: Fix warning in s_next of trace file ops
tracing: Include irqflags headers from trace clock