OSDN Git Service
Mitch Williams [Mon, 16 May 2016 17:26:36 +0000 (10:26 -0700)]
i40evf: don't overflow buffer
If the user adds an obscene amount of MAC addresses, the driver will run
into the situation where it has too many address requests to fit into a
single PF message. The driver checks for this case, and calculates the
maximum number of messages that it can send. Then it completely ignores
this count and overflows the buffer.
Fix this by checking the address count and bailing out of the loop at
the appropriate time.
Change-ID: If8dcbb04602c75941dc0cd8309065e1de9ca791c
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Catherine Sullivan [Mon, 16 May 2016 17:26:34 +0000 (10:26 -0700)]
i40e: Add a call to set the client interface down
We were failing to set the client interface down when we put the VSI
down. Add this call so that the client doesn't get an open called with
no close.
Also remove an un-needed delay. The VF should not be affected at all by
i40e_down.
Change-ID: I1135dffef534bf84e6fed57cf51bcf590e6cfaf7
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mitch Williams [Mon, 16 May 2016 17:26:33 +0000 (10:26 -0700)]
i40e: write HENA for VFs
Now that VF RSS is configured by the PF driver, it needs to set the RSS
Hash Enable registers by default. Without this, no packets will be
hashed and they'll all end up on queue 0.
Change-ID: I38e425f40ddb81e3b19a951cfbb939fa5b1123f1
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mitch Williams [Mon, 16 May 2016 17:26:32 +0000 (10:26 -0700)]
i40e: add hw struct local variable
This function uses the i40e_hw struct all over the place, so why doesn't
it keep a pointer to the struct? Add this pointer as a local variable
and use it consistently throughout the function.
Change-ID: I10eb688fe40909433fcb8ac7ac891cef67445d72
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Mitch Williams [Mon, 16 May 2016 17:26:31 +0000 (10:26 -0700)]
i40e: add functions to control default VSI
Add functions to enable and disable default VSI on a VEB. This allows
for configuration of limited promiscuous mode specifically for bridging
purposes.
Change-ID: I0cc5bd68b31c500fdff4d47e1f15d50d2739faf4
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
David S. Miller [Mon, 27 Jun 2016 14:41:02 +0000 (10:41 -0400)]
Merge branch 'sfp-infra'
Russell King says:
====================
Initial SFP support patches
Please review and merge this initial patch set, which is part of a
larger set previously posted adding SFP support to phy and mvneta.
This initial set are focused on cleaning up and reorganising the
fixed-phy code to allow the core software-phy code to be re-used.
These are based on net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Thu, 23 Jun 2016 13:50:25 +0000 (14:50 +0100)]
phy: improve safety of fixed-phy MII register reading
There is no prevention of a concurrent call to both fixed_mdio_read()
and fixed_phy_update_state(), which can result in the state being
modified while it's being inspected. Fix this by using a seqcount
to detect modifications, and memcpy()ing the state.
We remain slightly naughty here, calling link_update() and updating
the link status within the read-side loop - which would need rework
of the design to change.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Thu, 23 Jun 2016 13:50:20 +0000 (14:50 +0100)]
phy: generate swphy registers on the fly
Generate software phy registers as and when requested, rather than
duplicating the state in fixed_phy. This allows us to eliminate
the duplicate storage of of the same data, which is only different
in format.
As fixed_phy_update_regs() no longer updates register state, rename
it to fixed_phy_update().
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Thu, 23 Jun 2016 13:50:15 +0000 (14:50 +0100)]
phy: separate swphy state validation from register generation
Separate out the generation of MII registers from the state validation.
This allows us to simplify the error handing in fixed_phy() by allowing
earlier error detection.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Thu, 23 Jun 2016 13:50:10 +0000 (14:50 +0100)]
phy: convert swphy register generation to tabular form
Convert the swphy register generation to tabular form which allows us
to eliminate multiple switch() statements. This results in a smaller
object code size, more efficient, and easier to add support for faster
speeds.
Before:
Idx Name Size VMA LMA File off Algn
0 .text
00000164 00000000 00000000 00000034 2**2
text data bss dec hex filename
388 0 0 388 184 swphy.o
After:
Idx Name Size VMA LMA File off Algn
0 .text
000000fc 00000000 00000000 00000034 2**2
5 .rodata
00000028 00000000 00000000 00000138 2**2
text data bss dec hex filename
324 0 0 324 144 swphy.o
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King [Thu, 23 Jun 2016 13:50:05 +0000 (14:50 +0100)]
phy: move fixed_phy MII register generation to a library
Move the fixed_phy MII register generation to a library to allow other
software phy implementations to use this code.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 27 Jun 2016 14:33:42 +0000 (10:33 -0400)]
Merge tag 'linux-can-next-for-4.8-
20160623' of git://git./linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2016-06-17
this is a pull request of 4 patches for net-next/master.
Arnd Bergmann's patch fixes a regresseion in af_can introduced in
linux-can-next-for-4.8-
20160617. There are two patches by Ramesh
Shanmugasundaram, which add CAN-2.0 support to the rcar_canfd driver.
And a patch by Ed Spiridonov that adds better error diagnoses messages
to the Ed Spiridonov driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Amitoj Kaur Chawla [Thu, 23 Jun 2016 04:49:37 +0000 (10:19 +0530)]
tipc: Use kmemdup instead of kmalloc and memcpy
Replace calls to kmalloc followed by a memcpy with a direct call to
kmemdup.
The Coccinelle semantic patch used to make this change is as follows:
@@
expression from,to,size,flag;
statement S;
@@
- to = \(kmalloc\|kzalloc\)(size,flag);
+ to = kmemdup(from,size,flag);
if (to==NULL || ...) S
- memcpy(to, from, size);
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Wed, 22 Jun 2016 17:35:05 +0000 (18:35 +0100)]
ethernet: xircom: fix spelling mistakes on "excessive collisions"
trivial fixes to spelling mistakes of the words "excessive collisions"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Wed, 22 Jun 2016 16:42:21 +0000 (17:42 +0100)]
net: tc35815: fix spelling mistake on "descriptors"
trivial fixes to spelling mistakes of the word "descriptors"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 27 Jun 2016 08:10:47 +0000 (04:10 -0400)]
Merge branch 'mlx5e-100G-extensions'
Saeed Mahameed says:
====================
Mellanox 100G mlx5e Ethernet extensions
This series includes multiple features extensions for mlx5 Ethernet netdevice driver.
Namely, TX Rate limiting, RX interrupt moderation, ethtool settings.
TX Rate limiting:
- ConnectX-4 rate limiting infrastructure
- Set max rate NDO support
RX interrupt moderation:
- CQE based coalescing option (controlled via priv flags)
- Adaptive RX coalescing
ethtool settings:
- priv flags callbacks
- Support new ksettings API
- Add 50G missing link mode
- Support auto negotiation on/off
Applied on top:
0e9390ebf1fe ("Merge branch 'mlxsw-next'")
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Gal Pressman [Thu, 23 Jun 2016 14:02:46 +0000 (17:02 +0300)]
net/mlx5e: Report correct auto negotiation and allow toggling
Previous to this patch auto negotiation was reported off although it was
on by default in hardware. This patch reports the correct information to
ethtool and allows the user to toggle it on/off.
Added another parameter to set port proto function in order to pass
the auto negotiation field to the hardware.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gal Pressman [Thu, 23 Jun 2016 14:02:45 +0000 (17:02 +0300)]
net/mlx5e: Use new ethtool get/set link ksettings API
Use new get/set link ksettings and remove get/set settings legacy
callbacks.
This allows us to use bitmasks longer than 32 bit for supported and
advertised link modes and use modes that were previously not supported.
Signed-off-by: Gal Pressman <galp@mellanox.com>
CC: Ben Hutchings <bwh@kernel.org>
CC: David Decotigny <decot@googlers.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gal Pressman [Thu, 23 Jun 2016 14:02:44 +0000 (17:02 +0300)]
net/mlx5e: Add missing 50G baseSR2 link mode
Add MLX5E_50GBASE_SR2 as ETHTOOL_LINK_MODE_50000baseSR2_Full_BIT.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Cc: Ben Hutchings <bwh@kernel.org>
Cc: David Decotigny <decot@googlers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gal Pressman [Thu, 23 Jun 2016 14:02:43 +0000 (17:02 +0300)]
ethtool: Add 50G baseSR2 link mode
Add ETHTOOL_LINK_MODE_50000baseSR2_Full_BIT bit.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Cc: Ben Hutchings <bwh@kernel.org>
Cc: David Decotigny <decot@googlers.com>
Acked-By: David Decotigny <decot@googlers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gal Pressman [Thu, 23 Jun 2016 14:02:42 +0000 (17:02 +0300)]
net/mlx5e: Toggle link only after modifying port parameters
Add a dedicated function to toggle port link. It should be called only
after setting a port register.
Toggle will set port link to down and bring it back up in case that it's
admin status was up.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gil Rockah [Thu, 23 Jun 2016 14:02:41 +0000 (17:02 +0300)]
net/mlx5e: Support adaptive RX coalescing
Striving for high message rate and low interrupt rate.
Usage:
ethtool -C <interface> adaptive-rx on/off
Signed-off-by: Gil Rockah <gilr@mellanox.com>
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
CC: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tariq Toukan [Thu, 23 Jun 2016 14:02:40 +0000 (17:02 +0300)]
net/mlx5e: CQE based moderation
In this mode the moderation timer will restart upon
new completion (CQE) generation rather than upon interrupt
generation.
The outcome is that for bursty traffic the period timer will never
expire and thus only the moderation frames counter will dictate
interrupt generation, thus the interrupt rate will be relative
to the incoming packets size.
If the burst seizes for "moderation period" time then an interrupt
will be issued immediately.
CQE based moderation is off by default and can be controlled
via ethtool set_priv_flags.
Performance tested on ConnectX4-Lx 50G.
Less packet loss in netperf UDP and TCP tests, with no bw degradation,
for both single and multi streams, with message sizes of
64, 1024, 1472 and 32768 byte.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Gil Rockah <gilr@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gal Pressman [Thu, 23 Jun 2016 14:02:39 +0000 (17:02 +0300)]
net/mlx5e: Introduce net device priv flags infrastructure
Introduce an infrastructure for getting/setting private net device
flags.
Currently a 'nop' priv flag is added, following patches will override
the flag will actual feature specific flags.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yevgeny Petrilin [Thu, 23 Jun 2016 14:02:38 +0000 (17:02 +0300)]
net/mlx5e: Add TXQ set max rate support
Implement set_maxrate ndo.
Use the rate index from the hardware table to attach to channel SQ/TXQ.
In case of failure to configure new rate, the queue remains with
unlimited rate.
We save the configuration on priv structure and apply it each time
Send Queues are being reinitialized (after open/close) operations.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yevgeny Petrilin [Thu, 23 Jun 2016 14:02:37 +0000 (17:02 +0300)]
net/mlx5: Rate limit tables support
Configuring and managing HW rate limit tables.
The HW holds a table of rate limits, each rate is
associated with an index in that table.
Later a Send Queue uses this index to set the rate limit.
Multiple Send Queues can have the same rate limit, which is
represented by a single entry in this table.
Even though a rate can be shared, each queue is being rate
limited independently of others.
The SW shadow of this table holds the rate itself,
the index in the HW table and the refcount (number of queues)
working with this rate.
The exported functions are mlx5_rl_add_rate and mlx5_rl_remove_rate.
Number of different rates and their values are derived
from HW capabilities.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 27 Jun 2016 08:06:31 +0000 (04:06 -0400)]
Merge branch 'be2net-next'
Sathya Perla says:
====================
be2net: patch set
Hi Dave, pls consider commiting the following patches to the net-next tree.
Thanks!
Patch 1 replaces the be_max_eqs() macro with two new macros called
be_max_nic_eqs() and be_max_func_eqs() to clear confusion in that part
of the code.
Patch 2 adds support to configure asymmetric number of rx/tx queues via
ethtool set-channels option.
Patch 3 disables EVB when VFs are not enabled on a BE3 SR-IOV config to
avoid the broadcast echo problem.
Patch 4 updates copyright markings in be2net src files
Patch 5 updates the be2net maintainers' list
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sathya Perla [Wed, 22 Jun 2016 12:54:57 +0000 (08:54 -0400)]
be2net: update be2net maintainers list
This patch removes Padmanabh's name from the maintainers list as he's no
longer with the company. It also adds the driver name on the headline to
make it easy to lookup the maintainers list by the driver name.
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Somnath Kotur [Wed, 22 Jun 2016 12:54:56 +0000 (08:54 -0400)]
be2net: Change copyright markings in source files
This patch updates year and company name in the copyright markings in the
be2net source files.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Somnath Kotur [Wed, 22 Jun 2016 12:54:55 +0000 (08:54 -0400)]
be2net: Fix broadcast echoes from EVB in BE3
On SR-IOV profiles, when the user connects a Linux Bridge or OVS to a BE3
vport, they suffer the "broadcast/multicast echo" problem. BE3 EVB echoes
broadcast and multicast packets back to PF's vport confusing the
Linux bridge. BE3 relies on the src-mac addr being programmed on the
interface to avoid sending back an echo of a broadcast or multicast packet
on a vPort. When a Linux bridge is connected to a BE3, the mac-addr of the
VM behind the bridge doesn't get configured on the vPort and so echo
cancellation doesn't work.
This patch worksaround this problem by disabling the EVB initially
and re-enabling it *only* when SR-IOV is enabled by the user. For the
driver fix to work, the BE3 FW version must be >= 11.1.84.0.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sathya Perla [Wed, 22 Jun 2016 12:54:54 +0000 (08:54 -0400)]
be2net: support asymmetric rx/tx queue counts
be2net so far supported creation of RX/TX queues only in pairs.
On configs where rx and tx queue counts are different, creation of only
the lesser number of queues has been supported.
This patch now allows a combination of RX/TX-only channels along with
combined channels. N TX-queues and M RX-queues can be created with the
following cmds:
ethtool -L ethX combined N rx M-N (when N < M)
ethtool -L ethX combined M tx N-M (when M < N)
Setting both RX-only and TX-only channels is still not supported.
It is mandatory to create atleast one combined channel.
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sathya Perla [Wed, 22 Jun 2016 12:54:53 +0000 (08:54 -0400)]
be2net: fix definition of be_max_eqs()
The EQs available on a function are shared between NIC and RoCE.
The be_max_eqs() macro was so far being used to refer to the max number of
EQs available for NIC. This has caused some confusion in the code. To fix
this confusion this patch introduces a new macro called be_max_nic_eqs()
to refer to the max number of EQs avialable for NIC only and renames
be_max_eqs() to be_max_func_eqs().
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 27 Jun 2016 08:02:01 +0000 (04:02 -0400)]
Merge branch 'fec-new-type-device'
Andy Duan says:
====================
net: fec: add new type device
Different i.MX SOC FEC support different features like :
- i.MX6Q/DL FEC does not support AVB and interrupt coalesc
- i.MX6SX/i.MX7D supports AVB and interrupt coalesc
- i.MX6UL/ULL does not support AVB, but support interrupt coalesc
Then, add new quirk flag to judge the supported features, and add new
type device for i.MX6UL.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fugang Duan [Wed, 22 Jun 2016 10:52:36 +0000 (18:52 +0800)]
net: fec: use a more proper compatible string for i.MX6UL type device
i.MX6UL is a member in i.MX series family, the SOC FEC inherits from
i.MX6SX but removes some IP features, lets define a new type for fec
device.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fugang Duan [Wed, 22 Jun 2016 10:52:35 +0000 (18:52 +0800)]
net: fec: add interrupt coalesc quirk flag
Different i.MX SOC FEC support different features like :
- i.MX6Q/DL FEC does not support AVB and interrupt coalesc
- i.MX6SX/i.MX7D supports AVB and interrupt coalesc
- i.MX6UL/ULL does not support AVB, but support interrupt coalesc
So, add new quirk flag to judge the supported features.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 26 Jun 2016 20:01:54 +0000 (16:01 -0400)]
Merge tag 'rxrpc-rewrite-
20160622-2' of git://git./linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
rxrpc: Get rid of conn bundle and transport structs
Here's the next part of the AF_RXRPC rewrite. The primary purpose of this
set is to get rid of the rxrpc_conn_bundle and rxrpc_transport structs.
This simplifies things for future development of the connection handling.
To this end, the following significant changes are made:
(1) The rxrpc_connection struct is given pointers to the local and peer
endpoints, inside the rxrpc_conn_parameters struct. Pointers to the
transport's copy of these pointers are then redirected to the
connection struct.
(2) Exclusive connection handling is fixed. Exclusive connections should
do just one call and then be retired. They are used in security
negotiations and, I believe, the idea is to avoid reuse of negotiated
security contexts.
The current code is doing a single connection per socket and doing all
the calls over that. With this change it gets a new connection for
each call made.
(3) A new sendmsg() control message marker is added to make individual
calls operate over exclusive connections. This should be used in
future in preference to the sockopt that marks a socket as "exclusive
connection".
(4) IDs for client connections initiated by a machine are now allocated
from a global pool using the IDR facility and are unique across all
client connections, no matter their destination. The IDR facility is
then used to look up a connection on the connection ID alone. Other
parameters are then verified afterwards.
Note that the IDR facility may use a lot of memory if the IDs it holds
are widely scattered. Given this, in a future commit, client
connections will be retired if they are more than a certain distance
from the last ID allocated.
The client epoch is advanced by 1 each time the client ID counter
wraps. Connections outside the current epoch will also be retired in
a future commit.
(5) The connection bundle concept is removed and the client connection
tree is moved into the local endpoint. The queue for waiting for a
call channel is moved to the rxrpc_connection struct as there can only
be one connection for any particular key going to any particular peer
now.
(6) The rxrpc_transport struct is removed and the service connection tree
is moved into the peer struct.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Xing Zheng [Tue, 21 Jun 2016 12:33:28 +0000 (20:33 +0800)]
net: stmmac: dwmac-rk: add rk3228-specific data
Add constants and callback functions for the dwmac on rk3228/rk3229 socs.
As can be seen, the base structure is the same, only registers and the
bits in them moved slightly.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 25 Jun 2016 16:19:41 +0000 (12:19 -0400)]
Merge branch 'net-sched-bulk-dequeue'
Eric Dumazet says:
====================
net_sched: bulk dequeue and deferred drops
First patch adds an additional parameter to ->enqueue() qdisc method
so that drops can be done outside of critical section
(after locks are released).
Then fq_codel can have a small optimization to reduce number of cache
lines misses during a drop event
(possibly accumulating hundreds of packets to be freed).
A small htb change exports the backlog in class dumps.
Final patch adds bulk dequeue to qdiscs that were lacking this feature.
This series brings a nice qdisc performance increase (more than 80 %
in some cases).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 22 Jun 2016 06:16:52 +0000 (23:16 -0700)]
net_sched: generalize bulk dequeue
When qdisc bulk dequeue was added in linux-3.18 (commit
5772e9a3463b "qdisc: bulk dequeue support for qdiscs
with TCQ_F_ONETXQUEUE"), it was constrained to some
specific qdiscs.
With some extra care, we can extend this to all qdiscs,
so that typical traffic shaping solutions can benefit from
small batches (8 packets in this patch).
For example, HTB is often used on some multi queue device.
And bonding/team are multi queue devices...
Idea is to bulk-dequeue packets mapping to the same transmit queue.
This brings between 35 and 80 % performance increase in HTB setup
under pressure on a bonding setup :
1) NUMA node contention : 610,000 pps -> 1,110,000 pps
2) No node contention : 1,380,000 pps -> 1,930,000 pps
Now we should work to add batches on the enqueue() side ;)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: John Fastabend <john.r.fastabend@intel.com>
Cc: Jesper Dangaard Brouer <brouer@redhat.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Florian Westphal <fw@strlen.de>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 22 Jun 2016 06:16:51 +0000 (23:16 -0700)]
net_sched: sch_htb: export class backlog in dumps
We already get child qdisc qlen, we also can get its backlog
so that class dumps can report it.
Also replace qstats by a single drop counter, but move it in
a separate cache line so that drops do not dirty useful cache lines.
Tested:
$ tc -s cl sh dev eth0
class htb 1:1 root leaf 3: prio 0 rate 1Gbit ceil 1Gbit burst
500000b cburst
500000b
Sent
2183346912 bytes
9021815 pkt (dropped
2340774, overlimits 0 requeues 0)
rate 1001Mbit 517543pps backlog
120758b 499p requeues 0
lended:
9021770 borrowed: 0 giants: 0
tokens: 9 ctokens: 9
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 22 Jun 2016 06:16:50 +0000 (23:16 -0700)]
net_sched: fq_codel: cache skb->truesize into skb->cb
Now we defer skb drops, it makes sense to keep a copy
of skb->truesize in struct codel_skb_cb to avoid one
cache line miss per dropped skb in fq_codel_drop(),
to reduce latencies a bit further.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Wed, 22 Jun 2016 06:16:49 +0000 (23:16 -0700)]
net_sched: drop packets after root qdisc lock is released
Qdisc performance suffers when packets are dropped at enqueue()
time because drops (kfree_skb()) are done while qdisc lock is held,
delaying a dequeue() draining the queue.
Nominal throughput can be reduced by 50 % when this happens,
at a time we would like the dequeue() to proceed as fast as possible.
Even FQ is vulnerable to this problem, while one of FQ goals was
to provide some flow isolation.
This patch adds a 'struct sk_buff **to_free' parameter to all
qdisc->enqueue(), and in qdisc_drop() helper.
I measured a performance increase of up to 12 %, but this patch
is a prereq so that future batches in enqueue() can fly.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 25 Jun 2016 16:08:41 +0000 (12:08 -0400)]
Merge branch 'liquidio-next'
Raghu Vatsavayi says:
====================
liquidio: updates and bug fixes
Please consider following patch series for liquidio bug fixes
and updates on top of net-next. Following patches should be
applied in the following order as some of them depend on
earlier patches in the series.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Raghu Vatsavayi [Wed, 22 Jun 2016 05:53:15 +0000 (22:53 -0700)]
liquidio: ddr timeout
Adds support for ddr_timeout during device init.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <rvatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Raghu Vatsavayi [Wed, 22 Jun 2016 05:53:14 +0000 (22:53 -0700)]
liquidio: Support priv flag
This patch adds support for private flags for the driver.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <rvatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Raghu Vatsavayi [Wed, 22 Jun 2016 05:53:13 +0000 (22:53 -0700)]
liquidio: ptp info
This patch has minor changes for proper ptp info retreival.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <rvatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Raghu Vatsavayi [Wed, 22 Jun 2016 05:53:12 +0000 (22:53 -0700)]
liquidio: New xaui info
This patch adds support for host driver support for new Xaui
interfaces.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <rvatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Raghu Vatsavayi [Wed, 22 Jun 2016 05:53:11 +0000 (22:53 -0700)]
liquidio: New statistics support
This patch adds extensive support of statistics for data path,
control path and firmware.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <rvatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Raghu Vatsavayi [Wed, 22 Jun 2016 05:53:10 +0000 (22:53 -0700)]
liquidio: tx rx interrupt moderation
This patch has new tx/rx interrupt moderation defaults of
count/timer for better throughput and utilisation.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <rvatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Raghu Vatsavayi [Wed, 22 Jun 2016 05:53:09 +0000 (22:53 -0700)]
liquidio: chip reset changes
This patch resolves the order of chip reset while destroying
the resources by postoponing soft reset in destroy resources
function until all queues are removed properly.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <rvatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Raghu Vatsavayi [Wed, 22 Jun 2016 05:53:08 +0000 (22:53 -0700)]
liquidio: New unload state
This patch adds new state so that the ctrl packets are not sent
to firmware during unload time and only rx packets are allowed.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <rvatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Raghu Vatsavayi [Wed, 22 Jun 2016 05:53:07 +0000 (22:53 -0700)]
liquidio: Firmware image download
This patch has firmware image related changes for: firmware
release upon failure, support latest firmware version and
firmware download in 4MB chunks.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <rvatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Raghu Vatsavayi [Wed, 22 Jun 2016 05:53:06 +0000 (22:53 -0700)]
liquidio: Napi rx/tx traffic
This Patch adds tx buffer handling to Napi along with RX
traffic. Also separate spinlocks are introduced for handling
iq posting and buffer reclaim so that tx path and tx interrupt
do not compete against each other.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <rvatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Raghu Vatsavayi [Wed, 22 Jun 2016 05:53:05 +0000 (22:53 -0700)]
liquidio: Vlan filtering
This patch adds supports for Vlan filtering for liquidio driver.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <rvatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Raghu Vatsavayi [Wed, 22 Jun 2016 05:53:04 +0000 (22:53 -0700)]
liquidio: Vlan offloads changes
This patch adds support for vlan offloads for the driver and
receive header structures are also modified appropriately. Also
requestID will not be used in reveive header any more.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <rvatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Raghu Vatsavayi [Wed, 22 Jun 2016 05:53:03 +0000 (22:53 -0700)]
liquidio: soft command buffer limits
This patch increases the limits of soft command buffer size and
num command buffers. This patch also has changes for queue macros
and limit related changes for new chips.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <rvatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hariprasad Shenai [Wed, 22 Jun 2016 04:09:29 +0000 (09:39 +0530)]
cxgb4vf: Synchronize access to mailbox
The issue comes when there are multiple threads attempting to use the
mailbox facility at the same time. The issue is the for the Virtual
Function Driver, the only way to get the Virtual Interface statistics
is to issue mailbox commands to ask the firmware for the VI Stats.
And, because the VI Stats command can only retrieve a smallish number of
stats per mailbox command, we have to issue three mailbox commands in quick
succession. When ethtool or netstat command to get interface stats and
interface up/down is run in a loop for every 0.1 sec, we observed
mailbox collisions. And out of the two commands one would fail with
the present code, since we don't queue the second command.
To overcome the above issue, added a queue to access the mailbox.
Whenever a mailbox command is issued add it to the queue. If its at the
head issue the mailbox command, else wait for the existing command to
complete. Usually command takes less than a milli-second to complete.
Also timeout from the loop, if the command under execution takes
long time to run.
In reality, the number of mailbox access collisions is going to be very
rare since no one runs such abusive script.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
William Tu [Wed, 22 Jun 2016 04:05:58 +0000 (21:05 -0700)]
samples/bpf: set max locked memory to ulimited
Signed-off-by: William Tu <u9012063@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Philippe Reynes [Tue, 21 Jun 2016 22:32:36 +0000 (00:32 +0200)]
net: ethernet: macb: use phy_ethtool_{get|set}_link_ksettings
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Philippe Reynes [Tue, 21 Jun 2016 22:32:35 +0000 (00:32 +0200)]
net: ethernet: macb: use phydev from struct net_device
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jarno Rajahalme [Tue, 21 Jun 2016 21:59:38 +0000 (14:59 -0700)]
openvswitch: Only set mark and labels with a commit flag.
Only set conntrack mark or labels when the commit flag is specified.
This makes sure we can not set them before the connection has been
persisted, as in that case the mark and labels would be lost in an
event of an userspace upcall.
OVS userspace already requires the commit flag to accept setting
ct_mark and/or ct_labels. Validate for this in the kernel API.
Signed-off-by: Jarno Rajahalme <jarno@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jarno Rajahalme [Tue, 21 Jun 2016 21:59:37 +0000 (14:59 -0700)]
openvswitch: Set mark and labels before confirming.
Set conntrack mark and labels right before committing so that
the initial conntrack NEW event has the mark and labels.
Signed-off-by: Jarno Rajahalme <jarno@ovn.org>
Acked-by: Joe Stringer <joe@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Tue, 21 Jun 2016 16:28:20 +0000 (12:28 -0400)]
net: dsa: mv88e6xxx: rename single-chip support
With the upcoming support for cross-chip operations, it will be hard to
distinguish portions of code supporting a single-chip or a switch fabric
of interconnected chips.
Make the code clearer now, by renaming the mv88e6xxx_priv_state chip
structure to mv88e6xxx_chip. This patch brings no functional changes.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot [Tue, 21 Jun 2016 16:28:19 +0000 (12:28 -0400)]
net: dsa: mv88e6xxx: move driver in its own folder
With the upcoming support for cross-chip operations and other mv88e6xxx
enhancements, new files will be added.
Similarly to mlxsw or b53, move mv88e6xxx files into their own folder.
In the meantime, update the MAINTAINERS entry to please checkpatch.pl,
by replacing the invalid
88E6352 entry with 88E6XXX, maintained by
Andrew and myself.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 23 Jun 2016 19:56:54 +0000 (15:56 -0400)]
Merge branch 'qed-coalesce'
Sudarsana Reddy Kalluru says:
====================
qed*: coalesce parameters config support.
The patch series adds the support for config/read of the adapter coalesce
parameters. Patch (1) adds the qed infrastructure/APIs for the support and
patch (2) adds the driver support for following ethtool commands:
ethtool -c|--show-coalesce ethX
ethtool -C|--coalesce ethX [rx-usecs N] [tx-usecs N]
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Sudarsana Reddy Kalluru [Tue, 21 Jun 2016 13:36:22 +0000 (09:36 -0400)]
qede: Add support for coalescing config read/update.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sudarsana Reddy Kalluru [Tue, 21 Jun 2016 13:36:21 +0000 (09:36 -0400)]
qed: Add support for coalescing config read/update.
This patch adds support for configuring the device tx/rx coalescing
timeout values in the order of micro seconds. It also adds APIs for
upper layer drivers for reading/updating the coalescing values.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 23 Jun 2016 19:40:31 +0000 (15:40 -0400)]
Merge tag 'wireless-drivers-next-for-davem-2016-06-21' of git://git./linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers patches for 4.8
Major changes:
ath10k
* enable btcoex support without restarting firmware
* enable ipq4019 support using AHB bus
* add QCA9887 chipset support
* retrieve calibration data from EEPROM, currently only for QCA9887
wil6210
* add pm_notify handling
brcmfmac
* add support for the PCIE devices 43525 and 43465
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Rana Shahout [Tue, 21 Jun 2016 09:43:59 +0000 (12:43 +0300)]
net/mlx4_en: Add DCB PFC support through CEE netlink commands
This patch adds support for reading and updating priority flow
control (PFC) attributes in the driver via netlink.
Signed-off-by: Rana Shahout <ranas@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli [Tue, 21 Jun 2016 01:26:53 +0000 (18:26 -0700)]
net: dsa: b53: Fix statistics readings
Due to a typo we would always be using the MIB counter width of the
first element of the counter array instead of the current element, and
we would always be accessing the register statistics with a 64-bits
read, while some could be 32-bits. This got unnoticed in testing with
MDIO and SRAB which tolerate doing this, but testing with the SPI bus
revealed bogus values being returned. Fix this by using the proper
iterator here.
Fixes:
967dd82ffc52 ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Reported-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Tue, 21 Jun 2016 00:17:17 +0000 (01:17 +0100)]
of_mdio: Enable fixed PHY support if driver is a module
The fixed_phy driver doesn't have to be built-in, and it's
important that of_mdio supports it even if it's a module.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Tue, 21 Jun 2016 00:16:31 +0000 (01:16 +0100)]
ti_cpsw: Check for disabled child nodes
Dual MAC devices don't necessarily have both MACs wired up, so ignore
those that are disabled.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ed Spiridonov [Mon, 20 Jun 2016 18:40:15 +0000 (21:40 +0300)]
can: mcp251x: add message about sucessful/unsuccessful probe
Silent ignorance of errors during probe procedure is a bad thing, this
patch fixes it. Extra message added for hardware initialization
failure. Such common issues are mostly caused by wrong wiring. Message
about success added as well, it should be useful to debug new hardware
configuration, especially in case of several CAN buses.
Signed-off-by: Ed Spiridonov <edo.rus@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Ramesh Shanmugasundaram [Wed, 22 Jun 2016 12:31:47 +0000 (13:31 +0100)]
can: rcar_canfd: Add back-to-error-active support
As per Wolfgang G, all new drivers should support decreasing state
transition(back-to-error-active). This patch adds this support.
This driver configures the controller to halt on bus-off entry. Hence,
when in error states less than bus off state, the TEC/REC counters
are checked for lower state transition eligibility and action.
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Ramesh Shanmugasundaram [Wed, 22 Jun 2016 12:31:46 +0000 (13:31 +0100)]
can: rcar_canfd: Add Classical CAN only mode support
The controller can operate in one of the two global modes
- CAN FD only mode (default)
- Classical CAN (CAN2.0) only mode
This patch adds support for Classical CAN only mode. It can be enabled
by defining the optional device tree property "renesas,no-can-fd" of this
node.
Note: R-Car Gen3 h/w manual v0.51E shows bit6 of RSCFDnCFDGCFG as
reserved, which is incorrect. This bit is same as RSCFDnGCFG.
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Arnd Bergmann [Mon, 20 Jun 2016 15:51:52 +0000 (17:51 +0200)]
can: only call can_stat_update with procfs
The change to leave out procfs support in CAN when CONFIG_PROC_FS
is not set was incomplete and leads to a build error:
net/built-in.o: In function `can_init':
:(.init.text+0x9858): undefined reference to `can_stat_update'
ERROR: "can_stat_update" [net/can/can.ko] undefined!
This tries a better approach, encapsulating all of the calls
within IS_ENABLED(), so we also leave out the timer function
from the object file.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes:
a20fadf85312 ("can: build proc support only if CONFIG_PROC_FS is activated")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
William Tu [Mon, 20 Jun 2016 14:26:17 +0000 (07:26 -0700)]
openvswitch: Add packet len info to upcall.
The commit
f2a4d086ed4c ("openvswitch: Add packet truncation support.")
introduces packet truncation before sending to userspace upcall receiver.
This patch passes up the skb->len before truncation so that the upcall
receiver knows the original packet size. Potentially this will be used
by sFlow, where OVS translates sFlow config header=N to a sample action,
truncating packet to N byte in kernel datapath. Thus, only N bytes instead
of full-packet size is copied from kernel to userspace, saving the
kernel-to-userspace bandwidth.
Signed-off-by: William Tu <u9012063@gmail.com>
Cc: Pravin Shelar <pshelar@nicira.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Philippe Reynes [Sun, 19 Jun 2016 20:37:06 +0000 (22:37 +0200)]
net: ethernet: bgmac: use phy_ethtool_{get|set}_link_ksettings
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Philippe Reynes [Sun, 19 Jun 2016 20:37:05 +0000 (22:37 +0200)]
net: ethernet: bgmac: use phydev from struct net_device
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Philippe Reynes [Sat, 18 Jun 2016 14:37:21 +0000 (16:37 +0200)]
net: ethernet: altera_tse: use phy_ethtool_{get|set}_link_ksettings
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Philippe Reynes [Sat, 18 Jun 2016 14:37:20 +0000 (16:37 +0200)]
net: ethernet: altera_tse: use phydev from struct net_device
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Philippe Reynes [Sat, 18 Jun 2016 13:15:40 +0000 (15:15 +0200)]
net: ethernet: sun4i-emac: use phy_ethtool_{get|set}_link_ksettings
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Philippe Reynes [Sat, 18 Jun 2016 13:15:39 +0000 (15:15 +0200)]
net: ethernet: sun4i-emac: use phydev from struct net_device
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Howells [Fri, 17 Jun 2016 09:06:56 +0000 (10:06 +0100)]
rxrpc: Kill off the rxrpc_transport struct
The rxrpc_transport struct is now redundant, given that the rxrpc_peer
struct is now per peer port rather than per peer host, so get rid of it.
Service connection lists are transferred to the rxrpc_peer struct, as is
the conn_lock. Previous patches moved the client connection handling out
of the rxrpc_transport struct and discarded the connection bundling code.
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Fri, 17 Jun 2016 14:42:35 +0000 (15:42 +0100)]
rxrpc: Kill the client connection bundle concept
Kill off the concept of maintaining a bundle of connections to a particular
target service to increase the number of call slots available for any
beyond four for that service (there are four call slots per connection).
This will make cleaning up the connection handling code easier and
facilitate removal of the rxrpc_transport struct. Bundling can be
reintroduced later if necessary.
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Mon, 4 Apr 2016 13:00:38 +0000 (14:00 +0100)]
rxrpc: Provide more refcount helper functions
Provide refcount helper functions for connections so that the code doesn't
touch local or connection usage counts directly.
Also make it such that local and peer put functions can take a NULL
pointer.
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Fri, 17 Jun 2016 10:53:37 +0000 (11:53 +0100)]
rxrpc: Make rxrpc_send_packet() take a connection not a transport
Make rxrpc_send_packet() take a connection not a transport as part of the
phasing out of the rxrpc_transport struct.
Whilst we're at it, rename the function to rxrpc_send_data_packet() to
differentiate it from the other packet sending functions.
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Fri, 17 Jun 2016 10:07:55 +0000 (11:07 +0100)]
rxrpc: Calls displayed in /proc may in future lack a connection
Allocated rxrpc calls displayed in /proc/net/rxrpc_calls may in future be
on the proc list before they're connected or after they've been
disconnected - in which case they may not have a pointer to a connection
struct that can be used to get data from there.
Deal with this by using stuff from the call struct in preference where
possible and printing "no_connection" rather than a peer address if no
connection is assigned.
This change also has the added bonus that the service ID is now taken from
the call rather the connection which will allow per-call service upgrades
to be shown - something required for AuriStor server compatibility.
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Fri, 17 Jun 2016 10:00:48 +0000 (11:00 +0100)]
rxrpc: Validate the net address given to rxrpc_kernel_begin_call()
Validate the net address given to rxrpc_kernel_begin_call() before using
it.
Whilst this should be mostly unnecessary for in-kernel users, it does clear
the tail of the address struct in case we want to hash or compare the whole
thing.
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Mon, 4 Apr 2016 13:00:37 +0000 (14:00 +0100)]
rxrpc: Use IDR to allocate client conn IDs on a machine-wide basis
Use the IDR facility to allocate client connection IDs on a machine-wide
basis so that each client connection has a unique identifier. When the
connection ID space wraps, we advance the epoch by 1, thereby effectively
having a 62-bit ID space. The IDR facility is then used to look up client
connections during incoming packet routing instead of using an rbtree
rooted on the transport.
This change allows for the removal of the transport in the future and also
means that client connections can be looked up directly in the data-ready
handler by connection ID.
The ID management code is placed in a new file, conn-client.c, to which all
the client connection-specific code will eventually move.
Note that the IDR tree gets very expensive on memory if the connection IDs
are widely scattered throughout the number space, so we shall need to
retire connections that have, say, an ID more than four times the maximum
number of client conns away from the current allocation point to try and
keep the IDs concentrated. We will also need to retire connections from an
old epoch.
Also note that, for the moment, a pointer to the transport has to be passed
through into the ID allocation function so that we can take a BH lock to
prevent a locking issue against in-BH lookup of client connections. This
will go away later when RCU is used for server connections also.
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Tue, 21 Jun 2016 15:10:03 +0000 (16:10 +0100)]
rxrpc: rxrpc_connection_lock shouldn't be a BH lock, but conn_lock is
rxrpc_connection_lock shouldn't be accessed as a BH-excluding lock. It's
only accessed in a few places and none of those are in BH-context.
rxrpc_transport::conn_lock, however, *is* a BH-excluding lock and should be
accessed so consistently.
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Thu, 16 Jun 2016 12:31:07 +0000 (13:31 +0100)]
rxrpc: Pass sk_buff * rather than rxrpc_host_header * to functions
Pass a pointer to struct sk_buff rather than struct rxrpc_host_header to
functions so that they can in the future get at transport protocol parameters
rather than just RxRPC parameters.
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Mon, 4 Apr 2016 13:00:37 +0000 (14:00 +0100)]
rxrpc: Fix exclusive connection handling
"Exclusive connections" are meant to be used for a single client call and
then scrapped. The idea is to limit the use of the negotiated security
context. The current code, however, isn't doing this: it is instead
restricting the socket to a single virtual connection and doing all the
calls over that.
This is changed such that the socket no longer maintains a special virtual
connection over which it will do all the calls, but rather gets a new one
each time a new exclusive call is made.
Further, using a socket option for this is a poor choice. It should be
done on sendmsg with a control message marker instead so that calls can be
marked exclusive individually. To that end, add RXRPC_EXCLUSIVE_CALL
which, if passed to sendmsg() as a control message element, will cause the
call to be done on an single-use connection.
The socket option (RXRPC_EXCLUSIVE_CONNECTION) still exists and, if set,
will override any lack of RXRPC_EXCLUSIVE_CALL being specified so that
programs using the setsockopt() will appear to work the same.
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Mon, 4 Apr 2016 13:00:36 +0000 (14:00 +0100)]
rxrpc: Replace conn->trans->{local,peer} with conn->params.{local,peer}
Replace accesses of conn->trans->{local,peer} with
conn->params.{local,peer} thus making it easier for a future commit to
remove the rxrpc_transport struct.
This also reduces the number of memory accesses involved.
Signed-off-by: David Howells <dhowells@redhat.com>
David Howells [Mon, 4 Apr 2016 13:00:36 +0000 (14:00 +0100)]
rxrpc: Use structs to hold connection params and protocol info
Define and use a structure to hold connection parameters. This makes it
easier to pass multiple connection parameters around.
Define and use a structure to hold protocol information used to hash a
connection for lookup on incoming packet. Most of these fields will be
disposed of eventually, including the duplicate local pointer.
Whilst we're at it rename "proto" to "family" when referring to a protocol
family.
Signed-off-by: David Howells <dhowells@redhat.com>
Arnd Bergmann [Fri, 17 Jun 2016 09:55:22 +0000 (11:55 +0200)]
rxrpc: fix uninitialized variable use
Hashing the peer key was introduced for AF_INET, but gcc
warns about the rxrpc_peer_hash_key function returning uninitialized
data for any other value of srx->transport.family:
net/rxrpc/peer_object.c: In function 'rxrpc_peer_hash_key':
net/rxrpc/peer_object.c:57:15: error: 'p' may be used uninitialized in this function [-Werror=maybe-uninitialized]
Assuming that nothing else can be set here, this changes the
function to just return zero in case of an unknown address
family.
Fixes:
be6e6707f6ee ("rxrpc: Rework peer object handling to use hash table and RCU")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Dan Carpenter [Sat, 18 Jun 2016 08:44:03 +0000 (11:44 +0300)]
rxrpc: checking for IS_ERR() instead of NULL
rxrpc_lookup_peer_rcu() and rxrpc_lookup_peer() return NULL on error, never
error pointers, so IS_ERR() can't be used.
Fix three callers of those functions.
Fixes:
be6e6707f6ee ('rxrpc: Rework peer object handling to use hash table and RCU')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David Howells <dhowells@redhat.com>
David S. Miller [Tue, 21 Jun 2016 09:02:55 +0000 (05:02 -0400)]
Merge branch 'mlxsw-next'
Jiri Pirko says:
====================
mlxsw: Preparation for IPv4 router
Ido says:
This series prepares the driver for IPv4 router support. The router follow-up
patches are available at: https://github.com/jpirko/linux_mlxsw/tree/net-next_queue
Patches 1-9 simplify the netdevice notification block and also add several
checks during PRECHANGEUPPER events against topologies that aren't supported by
the device. This will ensure L3 interfaces are only configured on top of
valid netdevs.
Patches 10-13 contain trivial changes required for the introduction of a generic
FID struct - currently only used for vFIDs - in patch 14. Making the FID
struct generic will allow us to easily associate the underlying FIDs with
their L3-counterparts - Router interfaces (RIFs):
FID Type | Used by | RIF Type
--------------------------------------------------------
FID | The VLAN-aware bridge | VLAN
vFID | VLAN-unaware bridges | FID
rFID | non-bridged netdevs (follow-up) | Sub-port
Obligatory ASCII art to visualize the above:
A.B.C.D
+
| FID RIF
+
br0 E.F.G.H
+ +
| | VLAN RIF
+---------+---------+ +
| | br1.W
| vFID | +
| | |
vPort +-+-+ +-+-+ +
swXpY.Z | | | | br1
+-+-+ +-+-+ +
| | FID=W |
| | +------------+------------+
| | | |
+---+---+ +---+-+-+ +---+---+
| | | | | |
| | | | | |
| | | | | |
+-------+ +-------+ +-------+
swXpY
Patches 15-16 further generalize the struct by exploiting the fact that the
FID is a shared resource among ports. Each FID type is assigned a 'leave'
function that is invoked based on CHANGEUPPER events and takes care of the
necessary clean-up.
Patches 17-22 build upon the previous patches and use the FID struct for the
VLAN-aware bridge and take care of cleaning up FID resources in the 'leave'
functions. For now, these are only FDB records, but later on we'll have to
remove the RIFs associated with these FIDs, which will in turn take care of
routes and neighbours clean-up.
The last patch adds debug prints that proved very useful during the
development of this series.
Tested with the existing L2 recipes:
https://github.com/jpirko/lnst/tree/master/recipes/switchdev
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Mon, 20 Jun 2016 21:04:21 +0000 (23:04 +0200)]
mlxsw: spectrum: Add debug prints
For debug purposes, it's useful to know the order in which the driver
responds to changes in the topology of its upper devices.
Add debug prints to signal these events.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Mon, 20 Jun 2016 21:04:20 +0000 (23:04 +0200)]
mlxsw: spectrum: Free resources upon vPort destruction
There are situations in which a vPort is destroyed while still holding
references to device's resources such as FIDs and FDB records. This can
happen, for example, when a VLAN device is deleted while still being
bridged.
Instead of trying to make sure vPort destruction is invoked when it no
longer uses device's resources, just free them upon destruction. This
simplifies the code, as we no longer need to take different situations
into account when events are received - cleanup is taken care of in one
place.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>