OSDN Git Service
Lorenzo Bianconi [Sat, 22 Apr 2023 18:54:32 +0000 (20:54 +0200)]
net: veth: add page_pool for page recycling
Introduce page_pool support in veth driver in order to recycle pages
in veth_convert_skb_to_xdp_buff routine and avoid reallocating the skb
through the page allocator.
The patch has been tested sending tcp traffic to a veth pair where the
remote peer is running a simple xdp program just returning xdp_pass:
veth upstream codebase:
MTU 1500B: ~ 8Gbps
MTU 8000B: ~ 13.9Gbps
veth upstream codebase + pp support:
MTU 1500B: ~ 9.2Gbps
MTU 8000B: ~ 16.2Gbps
Tested-by: Maryam Tahhan <mtahhan@redhat.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Mon, 24 Apr 2023 22:37:35 +0000 (15:37 -0700)]
Merge tag 'nf-next-23-04-22' of git://git./linux/kernel/git/netfilter/nf-next
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
1) Reduce jumpstack footprint: Stash chain in last rule marker in blob for
tracing. Remove last rule and chain from jumpstack. From Florian Westphal.
2) nf_tables validates all tables before committing the new rules.
Unfortunately, this has two drawbacks:
- Since addition of the transaction mutex pernet state gets written to
outside of the locked section from the cleanup callback, this is
wrong so do this cleanup directly after table has passed all checks.
- Revalidate tables that saw no changes. This can be avoided by
keeping the validation state per table, not per netns.
From Florian Westphal.
3) Get rid of a few redundant pointers in the traceinfo structure.
The three removed pointers are used in the expression evaluation loop,
so gcc keeps them in registers. Passing them to the (inlined) helpers
thus doesn't increase nft_do_chain text size, while stack is reduced
by another 24 bytes on 64bit arches. From Florian Westphal.
4) IPVS cleanups in several ways without implementing any functional
changes, aside from removing some debugging output:
- Update width of source for ip_vs_sync_conn_options
The operation is safe, use an annotation to describe it properly.
- Consistently use array_size() in ip_vs_conn_init()
It seems better to use helpers consistently.
- Remove {Enter,Leave}Function. These seem to be well past their
use-by date.
- Correct spelling in comments.
From Simon Horman.
5) Extended netlink error report for netdevice in flowtables and
netdev/chains. Allow for incrementally add/delete devices to netdev
basechain. Allow to create netdev chain without device.
* tag 'nf-next-23-04-22' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf-next:
netfilter: nf_tables: allow to create netdev chain without device
netfilter: nf_tables: support for deleting devices in an existing netdev chain
netfilter: nf_tables: support for adding new devices to an existing netdev chain
netfilter: nf_tables: rename function to destroy hook list
netfilter: nf_tables: do not send complete notification of deletions
netfilter: nf_tables: extended netlink error reporting for netdevice
ipvs: Correct spelling in comments
ipvs: Remove {Enter,Leave}Function
ipvs: Consistently use array_size() in ip_vs_conn_init()
ipvs: Update width of source for ip_vs_sync_conn_options
netfilter: nf_tables: do not store rule in traceinfo structure
netfilter: nf_tables: do not store verdict in traceinfo structure
netfilter: nf_tables: do not store pktinfo in traceinfo structure
netfilter: nf_tables: remove unneeded conditional
netfilter: nf_tables: make validation state per table
netfilter: nf_tables: don't write table validation state without mutex
netfilter: nf_tables: don't store chain address on jump
netfilter: nf_tables: don't store address of last rule on jump
netfilter: nf_tables: merge nft_rules_old structure and end of ruleblob marker
====================
Link: https://lore.kernel.org/r/20230421235021.216950-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
David S. Miller [Mon, 24 Apr 2023 10:07:20 +0000 (11:07 +0100)]
Merge tag 'for-net-next-2023-04-23' of git://git./linux/kernel/git/bluetooth/bluetooth-next
bluetooth-next pull request for net-next:
- Introduce devcoredump support
- Add support for Realtek RTL8821CS, RTL8851B, RTL8852BS
- Add support for Mediatek MT7663, MT7922
- Add support for NXP w8997
- Add support for Actions Semi ATS2851
- Add support for QTI WCN6855
- Add support for Marvell 88W8997
Luiz Augusto von Dentz [Fri, 21 Apr 2023 18:37:55 +0000 (11:37 -0700)]
Bluetooth: hci_sync: Only allow hci_cmd_sync_queue if running
This makes sure hci_cmd_sync_queue only queue new work if HCI_RUNNING
has been set otherwise there is a risk of commands being sent while
turning off.
Because hci_cmd_sync_queue can no longer queue work while HCI_RUNNING is
not set it cannot be used to power on adapters so instead
hci_cmd_sync_submit is introduced which bypass the HCI_RUNNING check, so
it behaves like the old implementation.
Link: https://lore.kernel.org/all/CAB4PzUpDMvdc8j2MdeSAy1KkAE-D3woprCwAdYWeOc-3v3c9Sw@mail.gmail.com/
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tim Jiang [Wed, 19 Apr 2023 03:38:05 +0000 (11:38 +0800)]
Bluetooth: btusb: Add WCN6855 devcoredump support
WCN6855 will report memdump via ACL data or HCI event when
it get crashed, so we collect memdump to debug firmware.
Signed-off-by: Tim Jiang <quic_tjiang@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Neeraj Sanjay Kale [Wed, 19 Apr 2023 15:24:13 +0000 (20:54 +0530)]
Bluetooth: btnxpuart: Enable flow control before checking boot signature
This enables flow control before checking for bootloader signature and
deciding whether FW download is needed or not. In case of V1 bootloader
chips w8987 and w8997, it is observed that if WLAN FW is downloaded first
and power save is enabled in wlan core, bootloader signatures are not
emitted by the BT core when the chip is put to sleep. As a result, the
driver skips FW download and subsequent HCI commands get timeout errors
in dmesg as shown below:
[ 112.898867] Bluetooth: hci0: Opcode 0x c03 failed: -110
[ 114.914865] Bluetooth: hci0: Setting baudrate failed (-110)
[ 116.930856] Bluetooth: hci0: Setting wake-up method failed (-110)
By enabling the flow control, the host enables its RTS pin, and an
interrupt in chip's UART peripheral causes the bootloader to wake up,
enabling the bootloader signatures, which then helps in downloading
the bluetooth FW file.
This changes all instances of 0/1 for serdev_device_set_flow_control()
to false/true.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Archie Pusaka [Thu, 20 Apr 2023 12:23:36 +0000 (20:23 +0800)]
Bluetooth: Cancel sync command before suspend and power off
Some of the sync commands might take a long time to complete, e.g.
LE Create Connection when the peer device isn't responding might take
20 seconds before it times out. If suspend command is issued during
this time, it will need to wait for completion since both commands are
using the same sync lock.
This patch cancel any running sync commands before attempting to
suspend or adapter power off.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Ying Hsu <yinghsu@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Max Chou [Tue, 18 Apr 2023 05:43:54 +0000 (13:43 +0800)]
Bluetooth: btrtl: Add the support for RTL8851B
Add the support for RTL8851B BT controller on USB interface.
The necessary firmware will be submitted to linux-firmware project.
Note that the Bluetooth devices WITH the VID=0x0bda would be set the
feature quirk in btrtl_setup_realtek(). It's able to ignore the
feature flag set for the specific VID and PID in blacklist_table[] of
btusb.c. (check [1])
If Realtek Bluetooth chips WITHOUT the VID=0x0bda, it shall be added
the feature flag for the specific VID and PID in blacklist_table[] of
btusb.c. (check [2])
[1] '
9ab9235fe5cf ("Bluetooth: btrtl: Enable WBS for the specific
Realtek devices")'
[2] '
73280f13c9bb ("Bluetooth: btusb: Add the more support IDs for
Realtek RTL8822CE")'
The device info from /sys/kernel/debug/usb/devices as below.
T: Bus=03 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 33 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0bda ProdID=b851 Rev= 0.00
S: Manufacturer=Realtek
S: Product=802.11ax WLAN Adapter
S: SerialNumber=
00E04C885A01
C:* #Ifs= 3 Cfg#= 1 Atr=80 MxPwr=500mA
A: FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 8 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=09(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=0a(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=0b(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=0c(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Max Chou <max.chou@realtek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Luiz Augusto von Dentz [Tue, 18 Apr 2023 00:01:16 +0000 (17:01 -0700)]
Bluetooth: btnxpuart: Fix sparse warnings
This fixes the following sparse warnings:
drivers/bluetooth/btnxpuart.c:681:23: sparse: sparse:
restricted __le16 degrades to integer
drivers/bluetooth/btnxpuart.c:690:82: sparse:
sparse: incorrect type in argument 2 (different base types)
@@ expected unsigned short [usertype] req_len
@@ got restricted __le16 [usertype] len @@
drivers/bluetooth/btnxpuart.c:690:82: sparse:
expected unsigned short [usertype] req_len
drivers/bluetooth/btnxpuart.c:690:82: sparse:
got restricted __le16 [usertype] len
drivers/bluetooth/btnxpuart.c:694:84: sparse:
sparse: incorrect type in argument 2 (different base types)
@@ expected unsigned short [usertype] req_len
@@ got restricted __le16 [usertype] len @@
drivers/bluetooth/btnxpuart.c:694:84: sparse:
expected unsigned short [usertype] req_len
drivers/bluetooth/btnxpuart.c:694:84: sparse:
got restricted __le16 [usertype] len
drivers/bluetooth/btnxpuart.c:708:23: sparse:
sparse: incorrect type in assignment (different base types)
@@ expected unsigned int [usertype] requested_len
@@ got restricted __le16 [usertype] len @@
drivers/bluetooth/btnxpuart.c:708:23: sparse:
expected unsigned int [usertype] requested_len
drivers/bluetooth/btnxpuart.c:708:23: sparse:
got restricted __le16 [usertype] len
drivers/bluetooth/btnxpuart.c:787:78: sparse:
sparse: incorrect type in argument 2 (different base types)
@@ expected unsigned short [usertype] chipid
@@ got restricted __le16 [usertype] chip_id @@
drivers/bluetooth/btnxpuart.c:787:78: sparse:
expected unsigned short [usertype] chipid
drivers/bluetooth/btnxpuart.c:787:78: sparse:
got restricted __le16 [usertype] chip_id
drivers/bluetooth/btnxpuart.c:810:74: sparse:
sparse: incorrect type in argument 2 (different base types)
@@ expected unsigned short [usertype] req_len
@@ got restricted __le16 [usertype] len @@
drivers/bluetooth/btnxpuart.c:810:74: sparse:
expected unsigned short [usertype] req_len
drivers/bluetooth/btnxpuart.c:810:74: sparse:
got restricted __le16 [usertype] len
drivers/bluetooth/btnxpuart.c:815:76: sparse:
sparse: incorrect type in argument 2 (different base types)
@@ expected unsigned short [usertype] req_len
@@ got restricted __le16 [usertype] len @@
drivers/bluetooth/btnxpuart.c:815:76: sparse:
expected unsigned short [usertype] req_len
drivers/bluetooth/btnxpuart.c:815:76: sparse:
got restricted __le16 [usertype] len
drivers/bluetooth/btnxpuart.c:834:16: sparse:
sparse: restricted __le32 degrades to integer
drivers/bluetooth/btnxpuart.c:843:55: sparse:
sparse: restricted __le32 degrades to integer
drivers/bluetooth/btnxpuart.c:844:36: sparse:
sparse: incorrect type in argument 3 (different base types)
@@ expected unsigned long [usertype]
@@ got restricted __le16 [usertype] len @@
drivers/bluetooth/btnxpuart.c:844:36: sparse:
expected unsigned long [usertype]
drivers/bluetooth/btnxpuart.c:844:36: sparse:
got restricted __le16 [usertype] len
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/oe-kbuild-all/202304160736.Tsa0zTBU-lkp@intel.com/
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Max Chou [Mon, 17 Apr 2023 02:33:58 +0000 (10:33 +0800)]
Bluetooth: btrtl: Firmware format v2 support
Realtek changed the format of the firmware file as v2. The driver
should implement the patch to extract the firmware data from the
firmware file. The future chips must apply this patch for firmware loading.
This patch is compatible with the both previous format and v2 as well.
Signed-off-by: Allen Chen <allen_chen@realsil.com.cn>
Signed-off-by: Alex Lu <alex_lu@realsil.com.cn>
Tested-by: Hilda Wu <hildawu@realtek.com>
Signed-off-by: Max Chou <max.chou@realtek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Zijun Hu [Mon, 17 Apr 2023 09:39:59 +0000 (17:39 +0800)]
Bluetooth: Devcoredump: Fix storing u32 without specifying byte order issue
API hci_devcd_init() stores its u32 type parameter @dump_size into
skb, but it does not specify which byte order is used to store the
integer, let us take little endian to store and parse the integer.
Fixes:
f5cc609d09d4 ("Bluetooth: Add support for hci devcoredump")
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Ruihan Li [Sun, 16 Apr 2023 08:14:04 +0000 (16:14 +0800)]
bluetooth: Perform careful capability checks in hci_sock_ioctl()
Previously, capability was checked using capable(), which verified that the
caller of the ioctl system call had the required capability. In addition,
the result of the check would be stored in the HCI_SOCK_TRUSTED flag,
making it persistent for the socket.
However, malicious programs can abuse this approach by deliberately sharing
an HCI socket with a privileged task. The HCI socket will be marked as
trusted when the privileged task occasionally makes an ioctl call.
This problem can be solved by using sk_capable() to check capability, which
ensures that not only the current task but also the socket opener has the
specified capability, thus reducing the risk of privilege escalation
through the previously identified vulnerability.
Cc: stable@vger.kernel.org
Fixes:
f81f5b2db869 ("Bluetooth: Send control open and close messages for HCI raw sockets")
Signed-off-by: Ruihan Li <lrh2000@pku.edu.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Min Li [Mon, 17 Apr 2023 02:27:54 +0000 (10:27 +0800)]
Bluetooth: L2CAP: fix "bad unlock balance" in l2cap_disconnect_rsp
conn->chan_lock isn't acquired before l2cap_get_chan_by_scid,
if l2cap_get_chan_by_scid returns NULL, then 'bad unlock balance'
is triggered.
Reported-by: syzbot+9519d6b5b79cf7787cf3@syzkaller.appspotmail.com
Link: https://lore.kernel.org/all/000000000000894f5f05f95e9f4d@google.com/
Signed-off-by: Min Li <lm0963hack@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Ruihan Li [Sun, 16 Apr 2023 08:02:51 +0000 (16:02 +0800)]
bluetooth: Add cmd validity checks at the start of hci_sock_ioctl()
Previously, channel open messages were always sent to monitors on the first
ioctl() call for unbound HCI sockets, even if the command and arguments
were completely invalid. This can leave an exploitable hole with the abuse
of invalid ioctl calls.
This commit hardens the ioctl processing logic by first checking if the
command is valid, and immediately returning with an ENOIOCTLCMD error code
if it is not. This ensures that ioctl calls with invalid commands are free
of side effects, and increases the difficulty of further exploitation by
forcing exploitation to find a way to pass a valid command first.
Signed-off-by: Ruihan Li <lrh2000@pku.edu.cn>
Co-developed-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Liu Jian [Fri, 14 Apr 2023 10:30:06 +0000 (18:30 +0800)]
Revert "Bluetooth: btsdio: fix use after free bug in btsdio_remove due to unfinished work"
This reverts commit
1e9ac114c4428fdb7ff4635b45d4f46017e8916f.
This patch introduces a possible null-ptr-def problem. Revert it. And the
fixed bug by this patch have resolved by commit
73f7b171b7c0 ("Bluetooth:
btsdio: fix use after free bug in btsdio_remove due to race condition").
Fixes:
1e9ac114c442 ("Bluetooth: btsdio: fix use after free bug in btsdio_remove due to unfinished work")
Signed-off-by: Liu Jian <liujian56@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Raul Cheleguini [Thu, 23 Mar 2023 13:45:39 +0000 (10:45 -0300)]
Bluetooth: Add new quirk for broken set random RPA timeout for ATS2851
The ATS2851 based controller advertises support for command "LE Set Random
Private Address Timeout" but does not actually implement it, impeding the
controller initialization.
Add the quirk HCI_QUIRK_BROKEN_SET_RPA_TIMEOUT to unblock the controller
initialization.
< HCI Command: LE Set Resolvable Private... (0x08|0x002e) plen 2
Timeout: 900 seconds
> HCI Event: Command Status (0x0f) plen 4
LE Set Resolvable Private Address Timeout (0x08|0x002e) ncmd 1
Status: Unknown HCI Command (0x01)
Co-developed-by: imoc <wzj9912@gmail.com>
Signed-off-by: imoc <wzj9912@gmail.com>
Signed-off-by: Raul Cheleguini <raul.cheleguini@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Luiz Augusto von Dentz [Thu, 13 Apr 2023 00:45:51 +0000 (17:45 -0700)]
Bluetooth: hci_conn: Fix not waiting for HCI_EVT_LE_CIS_ESTABLISHED
When submitting HCI_OP_LE_CREATE_CIS the code shall wait for
HCI_EVT_LE_CIS_ESTABLISHED thus enforcing the serialization of
HCI_OP_LE_CREATE_CIS as the Core spec does not allow to send them in
parallel:
BLUETOOTH CORE SPECIFICATION Version 5.3 | Vol 4, Part E page 2566:
If the Host issues this command before all the HCI_LE_CIS_Established
events from the previous use of the command have been generated, the
Controller shall return the error code Command Disallowed (0x0C).
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Luiz Augusto von Dentz [Tue, 11 Apr 2023 23:14:25 +0000 (16:14 -0700)]
Bluetooth: hci_conn: Fix not matching by CIS ID
This fixes only matching CIS by address which prevents creating new hcon
if upper layer is requesting a specific CIS ID.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Luiz Augusto von Dentz [Tue, 11 Apr 2023 23:02:22 +0000 (16:02 -0700)]
Bluetooth: hci_conn: Add support for linking multiple hcon
Since it is required for some configurations to have multiple CIS with
the same peer which is now covered by iso-tester in the following test
cases:
ISO AC 6(i) - Success
ISO AC 7(i) - Success
ISO AC 8(i) - Success
ISO AC 9(i) - Success
ISO AC 11(i) - Success
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Dan Carpenter [Thu, 6 Apr 2023 08:55:17 +0000 (11:55 +0300)]
Bluetooth: vhci: Fix info leak in force_devcd_write()
There are a number of bugs here:
1) If "count" is less than sizeof(dump_data.data) then it copies
uninitialized data.
2) If simple_write_to_buffer() returns -EFAULT then we run into a
problem "ret < count" comparison. "count" is an unsigned long so the
comparison is type promoted to unsigned long and the negative returns
become high positive values. That also results in copying
uninitialized data.
3) If "*ppos" is non-zero then the first part of the dump_data
buffer is uninitialized. Using copy_from_user() instead of
simple_write_to_buffer() is more appropriate here.
Fixes:
d5d5df6da0aa ("Bluetooth: Add vhci devcoredump support")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Steev Klimaszewski [Wed, 12 Apr 2023 23:58:17 +0000 (18:58 -0500)]
Bluetooth: hci_qca: mark OF related data as maybe unused
The driver can be compile tested with !CONFIG_OF making certain data
unused.
Signed-off-by: Steev Klimaszewski <steev@kali.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Iulia Tanasescu [Tue, 11 Apr 2023 07:41:35 +0000 (10:41 +0300)]
Bluetooth: hci_conn: remove extra line in hci_le_big_create_sync
Remove extra line setting the broadcast code parameter of the
hci_cp_le_create_big struct to 0. The broadcast code is copied
from the QoS struct.
Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Lanzhe Li [Sun, 9 Apr 2023 13:02:29 +0000 (21:02 +0800)]
Bluetooth: fix inconsistent indenting
Fixed a wrong indentation before "return".This line uses a 7 space
indent instead of a tab.
Signed-off-by: Lanzhe Li <u202212060@hust.edu.cn>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Neeraj Sanjay Kale [Mon, 3 Apr 2023 12:24:30 +0000 (17:54 +0530)]
Bluetooth: btnxpuart: No need to check the received bootloader signature
We can never assume the uart will deliver a complete packet to the BT
layer at once, the expected packet may be divided into several parts by
uart as uart doesn't know the received packet size, the received data
count may mismatch with the expected packet size, so here
is_valid_bootloader_signature() check may always return false.
Even we remove the count check in is_valid_bootloader_signature(), then
the first part of the data which includes the packet type can pass the
is_valid_bootloader_signature() check, but the remaining parts don't
have the packet type data still cannot pass the check, here return
directly will cause the data loss.
So need to remove the received bootloader signature check here, the
h4_recv_buf() can help us combine the different data received into one
packet. If any out-of-sync or incomplete bootloader signature is received,
it is safe to ignore and discard it, and process the next bootloader
signature.
Co-developed-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Neeraj Sanjay Kale [Mon, 3 Apr 2023 12:24:29 +0000 (17:54 +0530)]
Bluetooth: btnxpuart: Disable Power Save feature on startup
This sets the default power save mode setting to disabled.
With this setting, this driver will behave like a normal h4 driver.
If user needs to use the power save feature, it can be enabled
using the following vendor command:
hcitool cmd 3f 23 02 00 00 (HCI_NXP_AUTO_SLEEP_MODE)
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Neeraj Sanjay Kale [Mon, 3 Apr 2023 12:24:28 +0000 (17:54 +0530)]
Bluetooth: btnxpuart: Deasset UART break before closing serdev device
This adds a call to ps_wakeup() before closing the serdev device, to
de-assert UART break.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Neeraj Sanjay Kale [Mon, 3 Apr 2023 12:24:27 +0000 (17:54 +0530)]
Bluetooth: btnxpuart: Add support to download helper FW file for w8997
This adds support to download helper FW file for the legacy NXP chipset
88w8997 for the btnxpuart driver. This helper FW file is necessary to
set the bootloader baudrate to
3000000 after which the actual BT FW file
can be downloaded. This change helps bring the FW download time from
around 10 sec to less than 2 sec for 88w8997 chip. For newer chipsets,
both V1 and V3 bootloader, driver sends the cmd5 and cmd7 to the chip
bootloader, and does not need a helper FW file.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Hans de Goede [Fri, 31 Mar 2023 21:11:24 +0000 (23:11 +0200)]
Bluetooth: hci_bcm: Add Acer Iconia One 7 B1-750 to the bcm_broken_irq_dmi_table
The DSDT for the Acer Iconia One 7 B1-750 models (which share
the same mainboard) specifies a IOAPIC IRQ for the HCI -> host IRQ but
this is not correct.
Like the Asus TF103C these tablets use pin 17 of the INT33FC:02 GPIO
controller for the IRQ and this pin is _not_ configured in direct IRQ
mode by the firmware.
Add a DMI match for this, re-using the Asus TF103C gpiod_lookup_table,
to fix bluetooth not working on these tablets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Hans de Goede [Fri, 31 Mar 2023 21:11:23 +0000 (23:11 +0200)]
Bluetooth: hci_bcm: Add Lenovo Yoga Tablet 2 830 / 1050 to the bcm_broken_irq_dmi_table
The DSDT for the Lenovo Yoga Tablet 2 830 / 1050 models (which share
the same mainboard) specifies a IOAPIC IRQ for the HCI -> host IRQ but
this is not correct.
Like the Asus TF103C these tablets use pin 17 of the INT33FC:02 GPIO
controller for the IRQ and this pin is _not_ configured in direct IRQ
mode by the firmware.
Add a DMI match for this, re-using the Asus TF103C gpiod_lookup_table,
to fix bluetooth not working on these tablets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Hans de Goede [Fri, 31 Mar 2023 21:11:22 +0000 (23:11 +0200)]
Bluetooth: hci_bcm: Limit bcm43430a0 / bcm43430a1 baudrate to
2000000
The bcm43430a0 and bcm43430a1 BT does not support the 0xfc45 command
to set the UART clock to 48 MHz and it also does not work at
4000000
baud without this command as some newer models do.
These chips are found on ACPI/x86 devices where the operating baudrate
does not come from the firmware but is hardcoded at
4000000, which does
not work.
Add a max_baudrate value to struct bcm_device_data and set this
to
2000000 on all known ACPI hardware-ids for the bcm43430a0
and the bcm43430a1.
Note this also adds the BCM2E9F ACPI HID which was missing until now.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Hans de Goede [Fri, 31 Mar 2023 21:11:21 +0000 (23:11 +0200)]
Bluetooth: hci_bcm: Fall back to getting bdaddr from EFI if not set
On some devices the BCM Bluetooth adapter does not have a valid bdaddr set.
btbcm.c currently sets HCI_QUIRK_INVALID_BDADDR to indicate when this is
the case. But this requires users to manual setup a btaddr, by doing e.g.:
btmgmt -i hci0 public-addr 'B0:F1:EC:82:1D:B3'
Which means that Bluetooth will not work out of the box on such devices.
To avoid this (where possible) hci_bcm sets: HCI_QUIRK_USE_BDADDR_PROPERTY
which tries to get the bdaddr from devicetree.
But this only works on devicetree platforms. On UEFI based platforms
there is a special Broadcom UEFI variable which when present contains
the devices bdaddr, just like how there is another UEFI variable which
contains wifi nvram contents including the wifi MAC address.
Add support for getting the bdaddr from this Broadcom UEFI variable,
so that Bluetooth will work OOTB for users on devices where this
UEFI variable is present.
This fixes Bluetooth not working on for example Asus T100HA 2-in-1s.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Qiqi Zhang [Tue, 4 Apr 2023 02:27:11 +0000 (10:27 +0800)]
Bluetooth: hci_h5: Complements reliable packet processing logic
As shown in the schematic diagram below.There may be a critical
scenario in the current code. If the device does not receive an
pure ack sent by the host due to insufficient receive buffer or
other reasons and triggers a retransmission, the host will always
be in an 'out-of-order' state.The state machine will get stuck.
host device
SEQ3,ACK4 --------->
<--------- SEQ4,ACK4
pure ACK ---------> (not received)
(out-of-order) <--------- SEQ4,ACK4(retransmission)
........
(out-of-order) <--------- SEQ4,ACK4(retransmission)
According to the description in the core specification: "whenever
a reliable packet is received, an acknowledgment shall be generated."
So set H5_TX_ACK_REQ bit to trigger retransmission of pure ack packet
when "out-of-order" occurs.
Signed-off-by: Qiqi Zhang <eddy.zhang@rock-chips.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Luiz Augusto von Dentz [Mon, 19 Dec 2022 21:37:02 +0000 (13:37 -0800)]
Bluetooth: Enable all supported LE PHY by default
This enables 2M and Coded PHY by default if they are marked as supported
in the LE features bits.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Iulia Tanasescu [Fri, 31 Mar 2023 15:38:01 +0000 (18:38 +0300)]
Bluetooth: Split bt_iso_qos into dedicated structures
Split bt_iso_qos into dedicated unicast and broadcast
structures and add additional broadcast parameters.
Fixes:
eca0ae4aea66 ("Bluetooth: Add initial implementation of BIS connections")
Signed-off-by: Iulia Tanasescu <iulia.tanasescu@nxp.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Abhishek Pandit-Subedi [Thu, 30 Mar 2023 16:58:26 +0000 (09:58 -0700)]
Bluetooth: btintel: Add Intel devcoredump support
Intercept debug exception events from the controller and put them into
a devcoredump using hci devcoredump APIs. The debug exception contains
data in a TLV format and it will be parsed in userspace.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Chethan Tumkur Narayan <chethan.tumkur.narayan@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Manish Mandlik [Thu, 30 Mar 2023 16:58:25 +0000 (09:58 -0700)]
Bluetooth: btusb: Add btusb devcoredump support
This patch implements the btusb driver side .coredump() callback to
trigger a devcoredump via sysfs.
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Manish Mandlik [Thu, 30 Mar 2023 16:58:24 +0000 (09:58 -0700)]
Bluetooth: Add vhci devcoredump support
Add devcoredump support for vhci that creates forcce_devcoredump debugfs
entry. This is used for mgmt-tester tests.
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Abhishek Pandit-Subedi [Thu, 30 Mar 2023 16:58:23 +0000 (09:58 -0700)]
Bluetooth: Add support for hci devcoredump
Add devcoredump APIs to hci core so that drivers only have to provide
the dump skbs instead of managing the synchronization and timeouts.
The devcoredump APIs should be used in the following manner:
- hci_devcoredump_init is called to allocate the dump.
- hci_devcoredump_append is called to append any skbs with dump data
OR hci_devcoredump_append_pattern is called to insert a pattern.
- hci_devcoredump_complete is called when all dump packets have been
sent OR hci_devcoredump_abort is called to indicate an error and
cancel an ongoing dump collection.
The high level APIs just prepare some skbs with the appropriate data and
queue it for the dump to process. Packets part of the crashdump can be
intercepted in the driver in interrupt context and forwarded directly to
the devcoredump APIs.
Internally, there are 5 states for the dump: idle, active, complete,
abort and timeout. A devcoredump will only be in active state after it
has been initialized. Once active, it accepts data to be appended,
patterns to be inserted (i.e. memset) and a completion event or an abort
event to generate a devcoredump. The timeout is initialized at the same
time the dump is initialized (defaulting to 10s) and will be cleared
either when the timeout occurs or the dump is complete or aborted.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Chethan T N [Tue, 21 Mar 2023 04:33:10 +0000 (10:03 +0530)]
Bluetooth: btintel: Add LE States quirk support
Basically all Intel controllers support both Central/Peripheral
LE states.
This patch enables the LE States quirk by default on all
Solar and Magnertor Intel controllers.
Signed-off-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Steev Klimaszewski [Sun, 26 Mar 2023 23:38:10 +0000 (18:38 -0500)]
Bluetooth: hci_qca: Add support for QTI Bluetooth chip wcn6855
Add regulators, GPIOs and changes required to power on/off wcn6855.
Add support for firmware download for wcn6855 which is in the
linux-firmware repository as hpbtfw21.tlv and hpnv21.bin.
Based on the assumption that this is similar to the wcn6750
Tested-on: BTFW.HSP.2.1.0-00538-VER_PATCHZ-1
Signed-off-by: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Tested-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Steev Klimaszewski [Sun, 26 Mar 2023 23:38:09 +0000 (18:38 -0500)]
dt-bindings: net: Add WCN6855 Bluetooth
Add bindings for the QTI WCN6855 chipset.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Steev Klimaszewski <steev@kali.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Max Chou [Tue, 21 Mar 2023 11:48:26 +0000 (19:48 +0800)]
Bluetooth: btrtl: check for NULL in btrtl_set_quirks()
The btrtl_set_quirks() has accessed btrtl_dev->ic_info->lmp_subver since
b8e482d02513. However, if installing a Realtek Bluetooth controller
without the driver supported, it will hit the NULL point accessed.
Add a check for NULL to avoid the Kernel Oops.
Signed-off-by: Max Chou <max.chou@realtek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Larry Finger [Thu, 23 Mar 2023 00:52:03 +0000 (19:52 -0500)]
bluetooth: Add device 13d3:3571 to device tables
This device is part of a Realtek RTW8852BE chip. The device table is as follows:
T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=13d3 ProdID=3571 Rev= 0.00
S: Manufacturer=Realtek
S: Product=Bluetooth Radio
S: SerialNumber=
00e04c000001
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Larry Finger [Thu, 23 Mar 2023 00:52:02 +0000 (19:52 -0500)]
bluetooth: Add device 0bda:887b to device tables
This device is part of a Realtek RTW8852BE chip.
The device table entry is as follows:
T: Bus=03 Lev=01 Prnt=01 Port=12 Cnt=02 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0bda ProdID=887b Rev= 0.00
S: Manufacturer=Realtek
S: Product=Bluetooth Radio
S: SerialNumber=
00e04c000001
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Arnd Bergmann [Wed, 22 Mar 2023 11:16:27 +0000 (12:16 +0100)]
Bluetooth: NXP: select CONFIG_CRC8
The driver needs both CRC32 and CRC8 to link correctly:
ld: drivers/bluetooth/btnxpuart.o: in function `nxp_serdev_probe':
drivers/bluetooth/btnxpuart.c:1214: undefined reference to
`crc8_populate_msb'
ld: drivers/bluetooth/btnxpuart.o: in function `nxp_send_ack':
drivers/bluetooth/btnxpuart.c:559: undefined reference to `crc8'
ld: drivers/bluetooth/btnxpuart.c:559: undefined reference to `crc8'
Fixes:
3e662aa4453a ("Bluetooth: NXP: Add protocol support for NXP Bluetooth chipsets")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Neeraj Sanjay Kale [Thu, 16 Mar 2023 17:22:14 +0000 (22:52 +0530)]
Bluetooth: NXP: Add protocol support for NXP Bluetooth chipsets
This adds a driver based on serdev driver for the NXP BT serial protocol
based on running H:4, which can enable the built-in Bluetooth device
inside an NXP BT chip.
This driver has Power Save feature that will put the chip into sleep state
whenever there is no activity for 2000ms, and will be woken up when any
activity is to be initiated over UART.
This driver enables the power save feature by default by sending the vendor
specific commands to the chip during setup.
During setup, the driver checks if a FW is already running on the chip
by waiting for the bootloader signature, and downloads device specific FW
file into the chip over UART if bootloader signature is received..
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Neeraj Sanjay Kale [Thu, 16 Mar 2023 17:22:13 +0000 (22:52 +0530)]
dt-bindings: net: bluetooth: Add NXP bluetooth support
Add binding document for NXP bluetooth chipsets attached over UART.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Neeraj Sanjay Kale [Thu, 16 Mar 2023 17:22:12 +0000 (22:52 +0530)]
serdev: Add method to assert break signal over tty UART port
Adds serdev_device_break_ctl() and an implementation for ttyport.
This function simply calls the break_ctl in tty layer, which can
assert a break signal over UART-TX line, if the tty and the
underlying platform and UART peripheral supports this operation.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Neeraj Sanjay Kale [Thu, 16 Mar 2023 17:22:11 +0000 (22:52 +0530)]
serdev: Replace all instances of ENOTSUPP with EOPNOTSUPP
This replaces all instances of ENOTSUPP with EOPNOTSUPP since ENOTSUPP
is not a standard error code. This will help maintain consistency in
error codes when new serdev API's are added.
Signed-off-by: Neeraj Sanjay Kale <neeraj.sanjaykale@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Ilpo Järvinen [Thu, 9 Mar 2023 08:20:30 +0000 (10:20 +0200)]
Bluetooth: hci_ldisc: Fix tty_set_termios() return value assumptions
tty_set_termios() never returns anything else than 0. Make the debug
prints to look directly into the new termios instead to check CRTSCTS
state.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Raul Cheleguini [Fri, 10 Mar 2023 15:14:10 +0000 (15:14 +0000)]
Bluetooth: Improve support for Actions Semi ATS2851 based devices
Add two more quirks to resume the device initialization and basic
operation as the device seems not to support "Read Transmit Power"
and "Set Extended Scan Parameters".
< HCI Command: LE Read Transmit Power (0x08|0x004b) plen 0
> HCI Event: Command Status (0x0f) plen 4
LE Read Transmit Power (0x08|0x004b) ncmd 1
Status: Unknown HCI Command (0x01)
< HCI Command: LE Set Extended Scan Parameters (0x08|0x0041) plen 8
Own address type: Random (0x01)
Filter policy: Accept all advertisement (0x00)
PHYs: 0x01
Entry 0: LE 1M
Type: Active (0x01)
Interval: 11.250 msec (0x0012)
Window: 11.250 msec (0x0012)
> HCI Event: Command Status (0x0f) plen 4
LE Set Extended Scan Parameters (0x08|0x0041) ncmd 1
Status: Unknown HCI Command (0x01)
Signed-off-by: Raul Cheleguini <rcheleguini@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Vasily Khoruzhick [Tue, 7 Mar 2023 22:17:31 +0000 (23:17 +0100)]
Bluetooth: btrtl: add support for the RTL8723CS
The Realtek RTL8723CS is a SDIO WiFi chip. It also contains a Bluetooth
module which is connected via UART to the host.
It shares lmp subversion with 8703B, so Realtek's userspace
initialization tool (rtk_hciattach) differentiates varieties of RTL8723CS
(CG, VF, XX) with RTL8703B using vendor's command to read chip type.
Also this chip declares support for some features it doesn't support
so add a quirk to indicate that these features are broken.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Bastian Germann <bage@debian.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Vasily Khoruzhick [Tue, 7 Mar 2023 22:17:30 +0000 (23:17 +0100)]
Bluetooth: Add new quirk for broken local ext features page 2
Some adapters (e.g. RTL8723CS) advertise that they have more than
2 pages for local ext features, but they don't support any features
declared in these pages. RTL8723CS reports max_page = 2 and declares
support for sync train and secure connection, but it responds with
either garbage or with error in status on corresponding commands.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Bastian Germann <bage@debian.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Krzysztof Kozlowski [Sat, 11 Mar 2023 11:13:54 +0000 (12:13 +0100)]
Bluetooth: btmtkuart: mark OF related data as maybe unused
The driver can be compile tested with !CONFIG_OF making certain data
unused:
drivers/bluetooth/btmtkuart.c:971:36: error: ‘mt7668_data’ defined
but not used [-Werror=unused-const-variable=]
drivers/bluetooth/btmtkuart.c:966:36: error: ‘mt7663_data’ defined
but not used [-Werror=unused-const-variable=]
drivers/bluetooth/btmtkuart.c:962:36: error: ‘mt7622_data’ defined
but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Krzysztof Kozlowski [Sat, 11 Mar 2023 11:13:53 +0000 (12:13 +0100)]
Bluetooth: hci_qca: mark OF related data as maybe unused
The driver can be compile tested with !CONFIG_OF making certain data
unused:
drivers/bluetooth/hci_qca.c:1869:37: error: ‘qca_soc_data_wcn6750’
defined but not used [-Werror=unused-const-variable=]
drivers/bluetooth/hci_qca.c:1853:37: error: ‘qca_soc_data_wcn3998’
defined but not used [-Werror=unused-const-variable=]
drivers/bluetooth/hci_qca.c:1841:37: error: ‘qca_soc_data_wcn3991’
defined but not used [-Werror=unused-const-variable=]
drivers/bluetooth/hci_qca.c:1830:37: error: ‘qca_soc_data_wcn3990’
defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Krzysztof Kozlowski [Sat, 11 Mar 2023 11:13:52 +0000 (12:13 +0100)]
Bluetooth: btmrvl_sdio: mark OF related data as maybe unused
The driver can be compile tested with !CONFIG_OF making certain data
unused:
drivers/bluetooth/btmrvl_sdio.c:43:34: error:
‘btmrvl_sdio_of_match_table’ defined but not used
[-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Krzysztof Kozlowski [Sat, 11 Mar 2023 11:13:51 +0000 (12:13 +0100)]
Bluetooth: hci_ll: drop of_match_ptr for ID table
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might not be relevant here).
drivers/bluetooth/hci_ll.c:769:34: error: ‘hci_ti_of_match’ defined
but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Luiz Augusto von Dentz [Thu, 9 Mar 2023 00:16:31 +0000 (16:16 -0800)]
Bluetooth: L2CAP: Delay identity address updates
This delays the identity address updates to give time for userspace to
process the new address otherwise there is a risk that userspace
creates a duplicated device if the MGMT event is delayed for some
reason.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Inga Stotland [Wed, 8 Mar 2023 18:32:35 +0000 (10:32 -0800)]
Bluetooth: hci_sync: Remove duplicate statement
This removes the following duplicate statement in
hci_le_ext_directed_advertising_sync():
cp.own_addr_type = own_addr_type;
Signed-off-by: Inga Stotland <inga.stotland@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Brian Gix [Fri, 24 Feb 2023 17:56:32 +0000 (09:56 -0800)]
Bluetooth: Convert MSFT filter HCI cmd to hci_sync
The msft_set_filter_enable() command was using the deprecated
hci_request mechanism rather than hci_sync. This caused the warning error:
hci0: HCI_REQ-0xfcf0
Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Archie Pusaka [Mon, 6 Mar 2023 09:07:07 +0000 (17:07 +0800)]
Bluetooth: hci_sync: Don't wait peer's reply when powering off
Currently, when we initiate disconnection, we will wait for the peer's
reply unless when we are suspending, where we fire and forget the
disconnect request.
A similar case is when adapter is powering off. However, we still wait
for the peer's reply in this case. Therefore, if the peer is
unresponsive, the command will time out and the power off sequence
will fail, causing "bluetooth powered on by itself" to users.
This patch makes the host doesn't wait for the peer's reply when the
disconnection reason is powering off.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Meng Tang [Mon, 6 Mar 2023 01:44:59 +0000 (09:44 +0800)]
Bluetooth: Add VID/PID 0489/e0e4 for MediaTek MT7922
Tested on Acer Nitro AN515-47 Notebook
output from /sys/kernel/debug/usb/devices:
T: Bus=03 Lev=01 Prnt=01 Port=02 Cnt=02 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0489 ProdID=e0e4 Rev= 1.00
S: Manufacturer=MediaTek Inc.
S: Product=Wireless_Device
S: SerialNumber=
000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us
I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us
Signed-off-by: Meng Tang <tangmeng@uniontech.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Chris Morgan [Tue, 28 Feb 2023 15:22:05 +0000 (09:22 -0600)]
arm64: dts: rockchip: Update compatible for bluetooth
Update the compatible for the Realtek RTL8821CS bluetooth node.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Chris Morgan [Tue, 28 Feb 2023 15:22:04 +0000 (09:22 -0600)]
Bluetooth: hci_h5: btrtl: Add support for RTL8821CS
RTL8821CS is a WiFi + Bluetooth combo chip from Realtek that provides
WiFi A/B/G/N/AC over an SDIO interface and Bluetooth 4.2 over a UART
interface.
Note that the firmware this was tested with was firmware version
0x75b8f098.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Chris Morgan [Tue, 28 Feb 2023 15:22:03 +0000 (09:22 -0600)]
dt-bindings: net: realtek-bluetooth: Add RTL8821CS
Add compatible string for RTL8821CS for existing Realtek Bluetooth
driver.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Alistair Francis <alistair@alistair23.me>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Meng Tang [Tue, 28 Feb 2023 05:55:17 +0000 (13:55 +0800)]
Bluetooth: btusb: Add new PID/VID 04ca:3801 for MT7663
This bluetooth device is found in a combo WLAN/BT card
for a MediaTek 7663.
Tested on Acer Aspire A315-24P Notebook
The device information:
T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=04ca ProdID=3801 Rev= 1.00
S: Manufacturer=MediaTek Inc.
S: Product=Wireless_Device
S: SerialNumber=
000000000
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
A: FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
Signed-off-by: Meng Tang <tangmeng@uniontech.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Luiz Augusto von Dentz [Mon, 27 Feb 2023 23:50:58 +0000 (15:50 -0800)]
Bluetooth: hci_sync: Fix smatch warning
This fixes the following new warning:
net/bluetooth/hci_sync.c:2403 hci_pause_addr_resolution() warn: missing
error code? 'err'
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Link: https://lore.kernel.org/r/202302251952.xryXOegd-lkp@intel.com/
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Luiz Augusto von Dentz [Fri, 24 Feb 2023 23:27:33 +0000 (15:27 -0800)]
Bluetooth: hci_core: Make hci_conn_hash_add append to the list
This makes hci_conn_hash_add append to the tail of the conn_hash so it
matches the order they are created, this is required if the controller
attempts to match the order of ACL with CIS which uses append logic
when programming the CIS ids on the CIG.
The result of this change affects Create CIS:
Before:
< HCI Command: LE Create Connected Isochronous Stream (0x08|0x0064) plen 9
Number of CIS: 2
CIS Handle: 2560
ACL Handle: 3586
CIS Handle: 2561
ACL Handle: 3585
After:
< HCI Command: LE Create Connected Isochronous Stream (0x08|0x0064) plen 9
Number of CIS: 2
CIS Handle: 2560
ACL Handle: 3585
CIS Handle: 2561
ACL Handle: 3586
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Victor Hassan [Wed, 22 Feb 2023 09:47:20 +0000 (17:47 +0800)]
Bluetooth: btrtl: Add support for RTL8852BS
Add the support for RTL8852BS BT controller on UART interface.
The necessary firmware file will be submitted to linux-firmware.
Signed-off-by: Victor Hassan <victor@allwinnertech.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Stefan Eichenberger [Mon, 13 Feb 2023 12:09:25 +0000 (13:09 +0100)]
Bluetooth: hci_mrvl: Add serdev support for 88W8997
Add serdev support for the 88W8997 from NXP (previously Marvell). It
includes support for changing the baud rate. The command to change the
baud rate is taken from the user manual UM11483 Rev. 9 in section 7
(Bring-up of Bluetooth interfaces) from NXP.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Stefan Eichenberger [Mon, 13 Feb 2023 12:09:24 +0000 (13:09 +0100)]
Bluetooth: hci_mrvl: use maybe_unused macro for device tree ids
Use the maybe_unused macro for the device tree ids instead of #ifdef
CONFIG_OF. This makes it easier to add support for new devices.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Stefan Eichenberger [Mon, 13 Feb 2023 12:09:23 +0000 (13:09 +0100)]
dt-bindings: bluetooth: marvell: add max-speed property
The 88W8997 bluetooth module supports setting the max-speed property.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Stefan Eichenberger [Mon, 13 Feb 2023 12:09:22 +0000 (13:09 +0100)]
dt-bindings: bluetooth: marvell: add 88W8997
Update the documentation with the device tree binding for the Marvell
88W8997 bluetooth device.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tomasz Moń [Tue, 7 Feb 2023 11:57:41 +0000 (12:57 +0100)]
Bluetooth: btusb: Do not require hardcoded interface numbers
Remove hardcoded interface number check because Bluetooth specification
since version 4.0 only recommends and no longer requires specific
interface numbers.
While earlier Bluetooth versions, i.e. 2.1 + EDR and 3.0 + HS, contain
required configuration table in Volume 4 - Host Controller Interface
Part B - USB Transport Layer, Bluetooth Core Specification Addendum 2
changes the table from required to recommended configuration.
Signed-off-by: Tomasz Moń <tomasz.mon@nordicsemi.no>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Luiz Augusto von Dentz [Mon, 13 Feb 2023 22:28:55 +0000 (14:28 -0800)]
Bluetooth: MGMT: Use BIT macro when defining bitfields
This makes use of BIT macro when defining bitfields which makes it
clearer what bit it is toggling.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
David S. Miller [Sun, 23 Apr 2023 17:35:27 +0000 (18:35 +0100)]
Merge branch 'act_pedit-minor-improvements'
Pedro Tammela says:
====================
net/sched: act_pedit: minor improvements
This series aims to improve the code and usability of act_pedit for
netlink users.
Patches 1-2 improves error reporting for extended keys parsing with extack.
Patch 3 checks the static offsets a priori on create/update. Currently,
this is done at the datapath for both static and runtime offsets.
Patch 4 removes a check from the datapath which is redundant since the
netlink parsing validates the key types.
Patch 5 changes the 'pr_info()' calls in the datapath to rate limited
versions.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pedro Tammela [Fri, 21 Apr 2023 21:25:17 +0000 (18:25 -0300)]
net/sched: act_pedit: rate limit datapath messages
Unbounded info messages in the pedit datapath can flood the printk
ring buffer quite easily depending on the action created.
As these messages are informational, usually printing some, not all,
is enough to bring attention to the real issue.
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pedro Tammela [Fri, 21 Apr 2023 21:25:16 +0000 (18:25 -0300)]
net/sched: act_pedit: remove extra check for key type
The netlink parsing already validates the key 'htype'.
Remove the datapath check as it's redundant.
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pedro Tammela [Fri, 21 Apr 2023 21:25:15 +0000 (18:25 -0300)]
net/sched: act_pedit: check static offsets a priori
Static key offsets should always be on 32 bit boundaries. Validate them on
create/update time for static offsets and move the datapath validation
for runtime offsets only.
iproute2 already errors out if a given offset and data size cannot be
packed to a 32 bit boundary. This change will make sure users which
create/update pedit instances directly via netlink also error out,
instead of finding out when packets are traversing.
Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pedro Tammela [Fri, 21 Apr 2023 21:25:14 +0000 (18:25 -0300)]
net/sched: act_pedit: use extack in 'ex' parsing errors
We have extack available when parsing 'ex' keys, so pass it to
tcf_pedit_keys_ex_parse and add more detailed error messages.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pedro Tammela [Fri, 21 Apr 2023 21:25:13 +0000 (18:25 -0300)]
net/sched: act_pedit: use NLA_POLICY for parsing 'ex' keys
Transform two checks in the 'ex' key parsing into netlink policies
removing extra if checks.
Signed-off-by: Pedro Tammela <pctammela@mojatatu.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yajun Deng [Fri, 21 Apr 2023 08:26:06 +0000 (16:26 +0800)]
net: sched: Print msecs when transmit queue time out
The kernel will print several warnings in a short period of time
when it stalls. Like this:
First warning:
[ 7100.097547] ------------[ cut here ]------------
[ 7100.097550] NETDEV WATCHDOG: eno2 (xxx): transmit queue 8 timed out
[ 7100.097571] WARNING: CPU: 8 PID: 0 at net/sched/sch_generic.c:467
dev_watchdog+0x260/0x270
...
Second warning:
[ 7147.756952] rcu: INFO: rcu_preempt self-detected stall on CPU
[ 7147.756958] rcu: 24-....: (59999 ticks this GP) idle=546/1/0x400000000000000
softirq=367 3137/
3673146 fqs=13844
[ 7147.756960] (t=60001 jiffies g=
4322709 q=133381)
[ 7147.756962] NMI backtrace for cpu 24
...
We calculate that the transmit queue start stall should occur before
7095s according to watchdog_timeo, the rcu start stall at 7087s.
These two times are close together, it is difficult to confirm which
happened first.
To let users know the exact time the stall started, print msecs when
the transmit queue time out.
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 23 Apr 2023 13:16:45 +0000 (14:16 +0100)]
Merge branch 'dsa-skb_mac_header'
Vladimir Oltean says:
====================
Remove skb_mac_header() dependency in DSA xmit path
Eric started working on removing skb_mac_header() assumptions from the
networking xmit path, and I offered to help for DSA:
https://lore.kernel.org/netdev/
20230321164519.
1286357-1-edumazet@google.com/
The majority of this patch set is a straightforward replacement of
skb_mac_header() with skb->data (hidden either behind skb_eth_hdr(), or
behind skb_vlan_eth_hdr()). The only patch which is more "interesting"
is 9/9.
Another potential caller of __skb_vlan_pop() on xmit (and therefore
also of skb_mac_header()) is tcf_vlan_act(), but I haven't had the time
to investigate that (enough to submit changes other than what's here).
v1->v2:
- 09/09: document the vlan_tci argument of vlan_remove_tag() in the kdoc
v1 at:
https://lore.kernel.org/netdev/
20230322233823.
1806736-1-vladimir.oltean@nxp.com/
Cc: Madalin Bucur <madalin.bucur@nxp.com>
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Thu, 20 Apr 2023 22:56:01 +0000 (01:56 +0300)]
net: dsa: tag_ocelot: call only the relevant portion of __skb_vlan_pop() on TX
ocelot_xmit_get_vlan_info() calls __skb_vlan_pop() as the most
appropriate helper I could find which strips away a VLAN header.
That's all I need it to do, but __skb_vlan_pop() has more logic, which
will become incompatible with the future revert of commit
6d1ccff62780
("net: reset mac header in dev_start_xmit()").
Namely, it performs a sanity check on skb_mac_header(), which will stop
being set after the above revert, so it will return an error instead of
removing the VLAN tag.
ocelot_xmit_get_vlan_info() gets called in 2 circumstances:
(1) the port is under a VLAN-aware bridge and the bridge sends
VLAN-tagged packets
(2) the port is under a VLAN-aware bridge and somebody else (an 8021q
upper) sends VLAN-tagged packets (using a VID that isn't in the
bridge vlan tables)
In case (1), there is actually no bug to defend against, because
br_dev_xmit() calls skb_reset_mac_header() and things continue to work.
However, in case (2), illustrated using the commands below, it can be
seen that our intervention is needed, since __skb_vlan_pop() complains:
$ ip link add br0 type bridge vlan_filtering 1 && ip link set br0 up
$ ip link set $eth master br0 && ip link set $eth up
$ ip link add link $eth name $eth.100 type vlan id 100 && ip link set $eth.100 up
$ ip addr add 192.168.100.1/24 dev $eth.100
I could fend off the checks in __skb_vlan_pop() with some
skb_mac_header_was_set() calls, but seeing how few callers of
__skb_vlan_pop() there are from TX paths, that seems rather
unproductive.
As an alternative solution, extract the bare minimum logic to strip a
VLAN header, and move it to a new helper named vlan_remove_tag(), close
to the definition of vlan_insert_tag(). Document it appropriately and
make ocelot_xmit_get_vlan_info() call this smaller helper instead.
Seeing that it doesn't appear illegal to test skb->protocol in the TX
path, I guess it would be a good for vlan_remove_tag() to also absorb
the vlan_set_encap_proto() function call.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Thu, 20 Apr 2023 22:56:00 +0000 (01:56 +0300)]
net: dsa: update TX path comments to not mention skb_mac_header()
Once commit
6d1ccff62780 ("net: reset mac header in dev_start_xmit()")
will be reverted, it will no longer be true that skb->data points at
skb_mac_header(skb) - since the skb->mac_header will not be set - so
stop saying that, and just say that it points to the MAC header.
I've reviewed vlan_insert_tag() and it does not *actually* depend on
skb_mac_header(), so reword that to avoid the confusion.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Thu, 20 Apr 2023 22:55:59 +0000 (01:55 +0300)]
net: dsa: tag_sja1105: replace skb_mac_header() with vlan_eth_hdr()
This is a cosmetic patch which consolidates the code to use the helper
function offered by if_vlan.h.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Thu, 20 Apr 2023 22:55:58 +0000 (01:55 +0300)]
net: dsa: tag_sja1105: don't rely on skb_mac_header() in TX paths
skb_mac_header() will no longer be available in the TX path when
reverting commit
6d1ccff62780 ("net: reset mac header in
dev_start_xmit()"). As preparation for that, let's use
skb_vlan_eth_hdr() to get to the VLAN header instead, which assumes it's
located at skb->data (assumption which holds true here).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Thu, 20 Apr 2023 22:55:57 +0000 (01:55 +0300)]
net: dsa: tag_ksz: do not rely on skb_mac_header() in TX paths
skb_mac_header() will no longer be available in the TX path when
reverting commit
6d1ccff62780 ("net: reset mac header in
dev_start_xmit()"). As preparation for that, let's use skb_eth_hdr() to
get to the Ethernet header's MAC DA instead, helper which assumes this
header is located at skb->data (assumption which holds true here).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Thu, 20 Apr 2023 22:55:56 +0000 (01:55 +0300)]
net: dsa: tag_ocelot: do not rely on skb_mac_header() for VLAN xmit
skb_mac_header() will no longer be available in the TX path when
reverting commit
6d1ccff62780 ("net: reset mac header in
dev_start_xmit()"). As preparation for that, let's use
skb_vlan_eth_hdr() to get to the VLAN header instead, which assumes it's
located at skb->data (assumption which holds true here).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Thu, 20 Apr 2023 22:55:55 +0000 (01:55 +0300)]
net: dpaa: avoid one skb_reset_mac_header() in dpaa_enable_tx_csum()
It appears that dpaa_enable_tx_csum() only calls skb_reset_mac_header()
to get to the VLAN header using skb_mac_header().
We can use skb_vlan_eth_hdr() to get to the VLAN header based on
skb->data directly. This avoids spending a few cycles to set
skb->mac_header.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Thu, 20 Apr 2023 22:55:54 +0000 (01:55 +0300)]
net: vlan: introduce skb_vlan_eth_hdr()
Similar to skb_eth_hdr() introduced in commit
96cc4b69581d ("macvlan: do
not assume mac_header is set in macvlan_broadcast()"), let's introduce a
skb_vlan_eth_hdr() helper which can be used in TX-only code paths to get
to the VLAN header based on skb->data rather than based on the
skb_mac_header(skb).
We also consolidate the drivers that dereference skb->data to go through
this helper.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Thu, 20 Apr 2023 22:55:53 +0000 (01:55 +0300)]
net: vlan: don't adjust MAC header in __vlan_insert_inner_tag() unless set
This is a preparatory change for the deletion of skb_reset_mac_header(skb)
from __dev_queue_xmit(). After that deletion, skb_mac_header(skb) will
no longer be set in TX paths, from which __vlan_insert_inner_tag() can
still be called (perhaps indirectly).
If we don't make this change, then an unset MAC header (equal to ~0U)
will become set after the adjustment with VLAN_HLEN.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ramón Nordin Rodriguez [Fri, 21 Apr 2023 16:38:54 +0000 (18:38 +0200)]
drivers/net/phy: add driver for Microchip LAN867x 10BASE-T1S PHY
This patch adds support for the Microchip LAN867x 10BASE-T1S family
(LAN8670/1/2). The driver supports P2MP with PLCA.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ramón Nordin Rodriguez <ramon.nordin.rodriguez@ferroamp.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gustavo A. R. Silva [Fri, 21 Apr 2023 13:08:53 +0000 (14:08 +0100)]
rxrpc: Replace fake flex-array with flexible-array member
Zero-length arrays as fake flexible arrays are deprecated and we are
moving towards adopting C99 flexible-array members instead.
Transform zero-length array into flexible-array member in struct
rxrpc_ackpacket.
Address the following warnings found with GCC-13 and
-fstrict-flex-arrays=3 enabled:
net/rxrpc/call_event.c:149:38: warning: array subscript i is outside array bounds of ‘uint8_t[0]’ {aka ‘unsigned char[]’} [-Warray-bounds=]
This helps with the ongoing efforts to tighten the FORTIFY_SOURCE
routines on memcpy() and help us make progress towards globally
enabling -fstrict-flex-arrays=3 [1].
Link: https://github.com/KSPP/linux/issues/21
Link: https://github.com/KSPP/linux/issues/263
Link: https://gcc.gnu.org/pipermail/gcc-patches/2022-October/602902.html
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Jeffrey Altman <jaltman@auristor.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: "David S. Miller" <davem@davemloft.net>
cc: Eric Dumazet <edumazet@google.com>
cc: Jakub Kicinski <kuba@kernel.org>
cc: Paolo Abeni <pabeni@redhat.com>
cc: linux-afs@lists.infradead.org
cc: netdev@vger.kernel.org
cc: linux-hardening@vger.kernel.org
Link: https://lore.kernel.org/r/ZAZT11n4q5bBttW0@work/
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 23 Apr 2023 12:35:08 +0000 (13:35 +0100)]
Merge branch 'napi_threaded_poll-enhancements'
Eric Dumazet says:
====================
net: give napi_threaded_poll() some love
There is interest to revert commit
4cd13c21b207
("softirq: Let ksoftirqd do its job") and use instead the
napi_threaded_poll() mode.
https://lore.kernel.org/netdev/
140f61e2e1fcb8cf53619709046e312e343b53ca.camel@redhat.com/T/#m8a8f5b09844adba157ad0d22fc1233d97013de50
Before doing so, make sure napi_threaded_poll() benefits
from recent core stack improvements, to further reduce
softirq triggers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 21 Apr 2023 09:43:57 +0000 (09:43 +0000)]
net: optimize napi_threaded_poll() vs RPS/RFS
We use napi_threaded_poll() in order to reduce our softirq dependency.
We can add a followup of
821eba962d95 ("net: optimize napi_schedule_rps()")
to further remove the need of firing NET_RX_SOFTIRQ whenever
RPS/RFS are used.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 21 Apr 2023 09:43:56 +0000 (09:43 +0000)]
net: make napi_threaded_poll() aware of sd->defer_list
If we call skb_defer_free_flush() from napi_threaded_poll(),
we can avoid to raise IPI from skb_attempt_defer_free()
when the list becomes too big.
This allows napi_threaded_poll() to rely less on softirqs,
and lowers latency caused by a too big list.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 21 Apr 2023 09:43:55 +0000 (09:43 +0000)]
net: move skb_defer_free_flush() up
We plan using skb_defer_free_flush() from napi_threaded_poll()
in the following patch.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 21 Apr 2023 09:43:54 +0000 (09:43 +0000)]
net: do not provide hard irq safety for sd->defer_lock
kfree_skb() can be called from hard irq handlers,
but skb_attempt_defer_free() is meant to be used
from process or BH contexts, and skb_defer_free_flush()
is meant to be called from BH contexts.
Not having to mask hard irq can save some cycles.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Fri, 21 Apr 2023 09:43:53 +0000 (09:43 +0000)]
net: add debugging checks in skb_attempt_defer_free()
Make sure skbs that are stored in softnet_data.defer_list
do not have a dst attached.
Also make sure the the skb was orphaned.
Link: https://lore.kernel.org/netdev/CANn89iJuEVe72bPmEftyEJHLzzN=QNR2yueFjTxYXCEpS5S8HQ@mail.gmail.com/T/
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>