OSDN Git Service
Dmitry Bogdanov [Wed, 8 Aug 2018 11:06:32 +0000 (14:06 +0300)]
net: aquantia: Fix IFF_ALLMULTI flag functionality
It was noticed that NIC always pass all multicast traffic to the host
regardless of IFF_ALLMULTI flag on the interface.
The rule in MC Filter Table in NIC, that is configured to accept any
multicast packets, is turning on if IFF_MULTICAST flag is set on the
interface. It leads to passing all multicast traffic to the host.
This fix changes the condition to turn on that rule by checking
IFF_ALLMULTI flag as it should.
Fixes:
b21f502f84be ("net:ethernet:aquantia: Fix for multicast filter handling.")
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Howells [Wed, 8 Aug 2018 10:30:02 +0000 (11:30 +0100)]
rxrpc: Fix the keepalive generator [ver #2]
AF_RXRPC has a keepalive message generator that generates a message for a
peer ~20s after the last transmission to that peer to keep firewall ports
open. The implementation is incorrect in the following ways:
(1) It mixes up ktime_t and time64_t types.
(2) It uses ktime_get_real(), the output of which may jump forward or
backward due to adjustments to the time of day.
(3) If the current time jumps forward too much or jumps backwards, the
generator function will crank the base of the time ring round one slot
at a time (ie. a 1s period) until it catches up, spewing out VERSION
packets as it goes.
Fix the problem by:
(1) Only using time64_t. There's no need for sub-second resolution.
(2) Use ktime_get_seconds() rather than ktime_get_real() so that time
isn't perceived to go backwards.
(3) Simplifying rxrpc_peer_keepalive_worker() by splitting it into two
parts:
(a) The "worker" function that manages the buckets and the timer.
(b) The "dispatch" function that takes the pending peers and
potentially transmits a keepalive packet before putting them back
in the ring into the slot appropriate to the revised last-Tx time.
(4) Taking everything that's pending out of the ring and splicing it into
a temporary collector list for processing.
In the case that there's been a significant jump forward, the ring
gets entirely emptied and then the time base can be warped forward
before the peers are processed.
The warping can't happen if the ring isn't empty because the slot a
peer is in is keepalive-time dependent, relative to the base time.
(5) Limit the number of iterations of the bucket array when scanning it.
(6) Set the timer to skip any empty slots as there's no point waking up if
there's nothing to do yet.
This can be triggered by an incoming call from a server after a reboot with
AF_RXRPC and AFS built into the kernel causing a peer record to be set up
before userspace is started. The system clock is then adjusted by
userspace, thereby potentially causing the keepalive generator to have a
meltdown - which leads to a message like:
watchdog: BUG: soft lockup - CPU#0 stuck for 23s! [kworker/0:1:23]
...
Workqueue: krxrpcd rxrpc_peer_keepalive_worker
EIP: lock_acquire+0x69/0x80
...
Call Trace:
? rxrpc_peer_keepalive_worker+0x5e/0x350
? _raw_spin_lock_bh+0x29/0x60
? rxrpc_peer_keepalive_worker+0x5e/0x350
? rxrpc_peer_keepalive_worker+0x5e/0x350
? __lock_acquire+0x3d3/0x870
? process_one_work+0x110/0x340
? process_one_work+0x166/0x340
? process_one_work+0x110/0x340
? worker_thread+0x39/0x3c0
? kthread+0xdb/0x110
? cancel_delayed_work+0x90/0x90
? kthread_stop+0x70/0x70
? ret_from_fork+0x19/0x24
Fixes:
ace45bec6d77 ("rxrpc: Fix firewall route keepalive")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 9 Aug 2018 02:07:38 +0000 (19:07 -0700)]
Merge branch 'mlx5-fixes'
Saeed Mahameed says:
====================
Mellanox, mlx5e fixes 2018-08-07
I know it is late into 4.18 release, and this is why I am submitting
only two mlx5e ethernet fixes.
The first one from Or, is needed for -stable and it fixes hairpin
for "same device" check.
The second fix is a non risk fix from Huy which cleans up and improves
error return value reporting for dcbnl_ieee_setapp.
For -stable v4.16
- net/mlx5e: Properly check if hairpin is possible between two functions
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Huy Nguyen [Wed, 8 Aug 2018 22:48:08 +0000 (15:48 -0700)]
net/mlx5e: Cleanup of dcbnl related fields
Remove unused netdev_registered_init/remove in en.h
Return ENOSUPPORT if the check MLX5_DSCP_SUPPORTED fails.
Remove extra white space
Fixes:
2a5e7a1344f4 ("net/mlx5e: Add dcbnl dscp to priority support")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Cc: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Or Gerlitz [Wed, 8 Aug 2018 22:48:07 +0000 (15:48 -0700)]
net/mlx5e: Properly check if hairpin is possible between two functions
The current check relies on function BDF addresses and can get
us wrong e.g when two VFs are assigned into a VM and the PCI
v-address is set by the hypervisor.
Fixes:
5c65c564c962 ('net/mlx5e: Support offloading TC NIC hairpin flows')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Alaa Hleihel <alaa@mellanox.com>
Tested-by: Alaa Hleihel <alaa@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang [Wed, 8 Aug 2018 03:43:04 +0000 (11:43 +0800)]
vhost: reset metadata cache when initializing new IOTLB
We need to reset metadata cache during new IOTLB initialization,
otherwise the stale pointers to previous IOTLB may be still accessed
which will lead a use after free.
Reported-by: syzbot+c51e6736a1bf614b3272@syzkaller.appspotmail.com
Fixes:
f88949138058 ("vhost: introduce O(1) vq metadata cache")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Tue, 7 Aug 2018 19:41:38 +0000 (12:41 -0700)]
llc: use refcount_inc_not_zero() for llc_sap_find()
llc_sap_put() decreases the refcnt before deleting sap
from the global list. Therefore, there is a chance
llc_sap_find() could find a sap with zero refcnt
in this global list.
Close this race condition by checking if refcnt is zero
or not in llc_sap_find(), if it is zero then it is being
removed so we can just treat it as gone.
Reported-by: <syzbot+278893f3f7803871f7ce@syzkaller.appspotmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey Kodanev [Tue, 7 Aug 2018 17:03:57 +0000 (20:03 +0300)]
dccp: fix undefined behavior with 'cwnd' shift in ccid2_cwnd_restart()
The shift of 'cwnd' with '(now - hc->tx_lsndtime) / hc->tx_rto' value
can lead to undefined behavior [1].
In order to fix this use a gradual shift of the window with a 'while'
loop, similar to what tcp_cwnd_restart() is doing.
When comparing delta and RTO there is a minor difference between TCP
and DCCP, the last one also invokes dccp_cwnd_restart() and reduces
'cwnd' if delta equals RTO. That case is preserved in this change.
[1]:
[40850.963623] UBSAN: Undefined behaviour in net/dccp/ccids/ccid2.c:237:7
[40851.043858] shift exponent 67 is too large for 32-bit type 'unsigned int'
[40851.127163] CPU: 3 PID: 15940 Comm: netstress Tainted: G W E 4.18.0-rc7.x86_64 #1
...
[40851.377176] Call Trace:
[40851.408503] dump_stack+0xf1/0x17b
[40851.451331] ? show_regs_print_info+0x5/0x5
[40851.503555] ubsan_epilogue+0x9/0x7c
[40851.548363] __ubsan_handle_shift_out_of_bounds+0x25b/0x2b4
[40851.617109] ? __ubsan_handle_load_invalid_value+0x18f/0x18f
[40851.686796] ? xfrm4_output_finish+0x80/0x80
[40851.739827] ? lock_downgrade+0x6d0/0x6d0
[40851.789744] ? xfrm4_prepare_output+0x160/0x160
[40851.845912] ? ip_queue_xmit+0x810/0x1db0
[40851.895845] ? ccid2_hc_tx_packet_sent+0xd36/0x10a0 [dccp]
[40851.963530] ccid2_hc_tx_packet_sent+0xd36/0x10a0 [dccp]
[40852.029063] dccp_xmit_packet+0x1d3/0x720 [dccp]
[40852.086254] dccp_write_xmit+0x116/0x1d0 [dccp]
[40852.142412] dccp_sendmsg+0x428/0xb20 [dccp]
[40852.195454] ? inet_dccp_listen+0x200/0x200 [dccp]
[40852.254833] ? sched_clock+0x5/0x10
[40852.298508] ? sched_clock+0x5/0x10
[40852.342194] ? inet_create+0xdf0/0xdf0
[40852.388988] sock_sendmsg+0xd9/0x160
...
Fixes:
113ced1f52e5 ("dccp ccid-2: Perform congestion-window validation")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ying Xue [Tue, 7 Aug 2018 07:52:32 +0000 (15:52 +0800)]
tipc: fix an interrupt unsafe locking scenario
Commit
9faa89d4ed9d ("tipc: make function tipc_net_finalize() thread
safe") tries to make it thread safe to set node address, so it uses
node_list_lock lock to serialize the whole process of setting node
address in tipc_net_finalize(). But it causes the following interrupt
unsafe locking scenario:
CPU0 CPU1
---- ----
rht_deferred_worker()
rhashtable_rehash_table()
lock(&(&ht->lock)->rlock)
tipc_nl_compat_doit()
tipc_net_finalize()
local_irq_disable();
lock(&(&tn->node_list_lock)->rlock);
tipc_sk_reinit()
rhashtable_walk_enter()
lock(&(&ht->lock)->rlock);
<Interrupt>
tipc_disc_rcv()
tipc_node_check_dest()
tipc_node_create()
lock(&(&tn->node_list_lock)->rlock);
*** DEADLOCK ***
When rhashtable_rehash_table() holds ht->lock on CPU0, it doesn't
disable BH. So if an interrupt happens after the lock, it can create
an inverse lock ordering between ht->lock and tn->node_list_lock. As
a consequence, deadlock might happen.
The reason causing the inverse lock ordering scenario above is because
the initial purpose of node_list_lock is not designed to do the
serialization of node address setting.
As cmpxchg() can guarantee CAS (compare-and-swap) process is atomic,
we use it to replace node_list_lock to ensure setting node address can
be atomically finished. It turns out the potential deadlock can be
avoided as well.
Fixes:
9faa89d4ed9d ("tipc: make function tipc_net_finalize() thread safe")
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <maloy@donjonn.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Mon, 6 Aug 2018 18:06:02 +0000 (11:06 -0700)]
vsock: split dwork to avoid reinitializations
syzbot reported that we reinitialize an active delayed
work in vsock_stream_connect():
ODEBUG: init active (active state 0) object type: timer_list hint:
delayed_work_timer_fn+0x0/0x90 kernel/workqueue.c:1414
WARNING: CPU: 1 PID: 11518 at lib/debugobjects.c:329
debug_print_object+0x16a/0x210 lib/debugobjects.c:326
The pattern is apparently wrong, we should only initialize
the dealyed work once and could repeatly schedule it. So we
have to move out the initializations to allocation side.
And to avoid confusion, we can split the shared dwork
into two, instead of re-using the same one.
Fixes:
d021c344051a ("VSOCK: Introduce VM Sockets")
Reported-by: <syzbot+8a9b1bd330476a4f3db6@syzkaller.appspotmail.com>
Cc: Andy king <acking@vmware.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Cc: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Colin Ian King [Mon, 6 Aug 2018 16:50:45 +0000 (17:50 +0100)]
net: thunderx: check for failed allocation lmac->dmacs
The allocation of lmac->dmacs is not being checked for allocation
failure. Add the check.
Fixes:
3a34ecfd9d3f ("net: thunderx: add MAC address filter tracking for LMAC")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Al Viro [Sun, 5 Aug 2018 17:22:38 +0000 (18:22 +0100)]
cxgb4: mk_act_open_req() buggers ->{local, peer}_ip on big-endian hosts
Unlike fs.val.lport and fs.val.fport, cxgb4_process_flow_match()
sets fs.val.{l,f}ip to net-endian values without conversion - they come
straight from flow_dissector_key_ipv4_addrs ->dst and ->src resp. So
the assignment in mk_act_open_req() ought to be a straight copy.
As far as I know, T4 PCIe cards do exist, so it's not as if that
thing could only be found on little-endian systems...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Willem de Bruijn [Mon, 6 Aug 2018 14:38:34 +0000 (10:38 -0400)]
packet: refine ring v3 block size test to hold one frame
TPACKET_V3 stores variable length frames in fixed length blocks.
Blocks must be able to store a block header, optional private space
and at least one minimum sized frame.
Frames, even for a zero snaplen packet, store metadata headers and
optional reserved space.
In the block size bounds check, ensure that the frame of the
chosen configuration fits. This includes sockaddr_ll and optional
tp_reserve.
Syzbot was able to construct a ring with insuffient room for the
sockaddr_ll in the header of a zero-length frame, triggering an
out-of-bounds write in dev_parse_header.
Convert the comparison to less than, as zero is a valid snap len.
This matches the test for minimum tp_frame_size immediately below.
Fixes:
f6fb8f100b80 ("af-packet: TPACKET_V3 flexible buffer implementation.")
Fixes:
eb73190f4fbe ("net/packet: refine check for priv area size")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xin Long [Sun, 5 Aug 2018 14:46:07 +0000 (22:46 +0800)]
ip6_tunnel: use the right value for ipv4 min mtu check in ip6_tnl_xmit
According to RFC791, 68 bytes is the minimum size of IPv4 datagram every
device must be able to forward without further fragmentation while 576
bytes is the minimum size of IPv4 datagram every device has to be able
to receive, so in ip6_tnl_xmit(), 68(IPV4_MIN_MTU) should be the right
value for the ipv4 min mtu check in ip6_tnl_xmit.
While at it, change to use max() instead of if statement.
Fixes:
c9fefa08190f ("ip6_tunnel: get the min mtu properly in ip6_tnl_xmit")
Reported-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Fri, 3 Aug 2018 06:20:38 +0000 (23:20 -0700)]
ipv6: fix double refcount of fib6_metrics
All the callers of ip6_rt_copy_init()/rt6_set_from() hold refcnt
of the "from" fib6_info, so there is no need to hold fib6_metrics
refcnt again, because fib6_metrics refcnt is only released when
fib6_info is gone, that is, they have the same life time, so the
whole fib6_metrics refcnt can be removed actually.
This fixes a kmemleak warning reported by Sabrina.
Fixes:
93531c674315 ("net/ipv6: separate handling of FIB entries from dst based routes")
Reported-by: Sabrina Dubroca <sd@queasysnail.net>
Cc: Sabrina Dubroca <sd@queasysnail.net>
Cc: David Ahern <dsahern@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 5 Aug 2018 19:37:41 +0000 (12:37 -0700)]
Linux 4.18-rc8
Linus Torvalds [Sun, 5 Aug 2018 16:39:30 +0000 (09:39 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull x86 fix from Thomas Gleixner:
"A single fix, which addresses boot failures on machines which do not
report EBDA correctly, which can place the trampoline into reserved
memory regions. Validating against E820 prevents that"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/boot/compressed/64: Validate trampoline placement against E820
Linus Torvalds [Sun, 5 Aug 2018 16:25:29 +0000 (09:25 -0700)]
Merge branch 'timers-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"Two oneliners addressing NOHZ failures:
- Use a bitmask to check for the pending timer softirq and not the
bit number. The existing code using the bit number checked for
the wrong bit, which caused timers to either expire late or stop
completely.
- Make the nohz evaluation on interrupt exit more robust. The
existing code did not re-arm the hardware when interrupting a
running softirq in task context (ksoftirqd or tail of
local_bh_enable()), which caused timers to either expire late
or stop completely"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
nohz: Fix missing tick reprogram when interrupting an inline softirq
nohz: Fix local_timer_softirq_pending()
Linus Torvalds [Sun, 5 Aug 2018 16:13:07 +0000 (09:13 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull perf fixes from Thomas Gleixner:
"A set of fixes for perf:
Kernel side:
- Fix the hardcoded index of extra PCI devices on Broadwell which
caused a resource conflict and triggered warnings on CPU hotplug.
Tooling:
- Update the tools copy of several files, including perf_event.h,
powerpc's asm/unistd.h (new io_pgetevents syscall), bpf.h and x86's
memcpy_64.s (used in 'perf bench mem'), silencing the respective
warnings during the perf tools build.
- Fix the build on the alpine:edge distro"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel/uncore: Fix hardcoded index of Broadwell extra PCI devices
perf tools: Fix the build on the alpine:edge distro
tools arch: Update arch/x86/lib/memcpy_64.S copy used in 'perf bench mem memcpy'
tools headers uapi: Refresh linux/bpf.h copy
tools headers powerpc: Update asm/unistd.h copy to pick new
tools headers uapi: Update tools's copy of linux/perf_event.h
Linus Torvalds [Sun, 5 Aug 2018 15:55:26 +0000 (08:55 -0700)]
Merge branch 'irq-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull irq fix from Thomas Gleixner:
"A single bugfix for the irq core to prevent silent data corruption and
malfunction of threaded interrupts under certain conditions"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Make force irq threading setup more robust
Linus Torvalds [Sun, 5 Aug 2018 15:20:39 +0000 (08:20 -0700)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
1) Handle frames in error situations properly in AF_XDP, from Jakub
Kicinski.
2) tcp_mmap test case only tests ipv6 due to a thinko, fix from
Maninder Singh.
3) Session refcnt fix in l2tp_ppp, from Guillaume Nault.
4) Fix regression in netlink bind handling of multicast gruops, from
Dmitry Safonov.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
netlink: Don't shift on 64 for ngroups
net/smc: no cursor update send in state SMC_INIT
l2tp: fix missing refcount drop in pppol2tp_tunnel_ioctl()
mlxsw: core_acl_flex_actions: Remove redundant mirror resource destruction
mlxsw: core_acl_flex_actions: Remove redundant counter destruction
mlxsw: core_acl_flex_actions: Remove redundant resource destruction
mlxsw: core_acl_flex_actions: Return error for conflicting actions
selftests/bpf: update test_lwt_seg6local.sh according to iproute2
drivers: net: lmc: fix case value for target abort error
selftest/net: fix protocol family to work for IPv4.
net: xsk: don't return frames via the allocator on error
tools/bpftool: fix a percpu_array map dump problem
Linus Torvalds [Sun, 5 Aug 2018 01:34:55 +0000 (18:34 -0700)]
Merge tag 'usercopy-fix-v4.18-rc8' of git://git./linux/kernel/git/kees/linux
Pull usercopy whitelisting fix from Kees Cook:
"Bart Massey discovered that the usercopy whitelist for JFS was
incomplete: the inline inode data may intentionally "overflow" into
the neighboring "extended area", so the size of the whitelist needed
to be raised to include the neighboring field"
* tag 'usercopy-fix-v4.18-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
jfs: Fix usercopy whitelist for inline inode data
Linus Torvalds [Sun, 5 Aug 2018 01:30:58 +0000 (18:30 -0700)]
Merge tag 'xfs-4.18-fixes-5' of git://git./fs/xfs/xfs-linux
Pull xfs bugfix from Darrick Wong:
"One more patch for 4.18 to fix a coding error in the iomap_bmap()
function introduced in -rc1: fix incorrect shifting"
* tag 'xfs-4.18-fixes-5' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
fs: fix iomap_bmap position calculation
Linus Torvalds [Fri, 3 Aug 2018 19:22:09 +0000 (12:22 -0700)]
Partially revert "block: fail op_is_write() requests to read-only partitions"
It turns out that commit
721c7fc701c7 ("block: fail op_is_write()
requests to read-only partitions"), while obviously correct, causes
problems for some older lvm2 installations.
The reason is that the lvm snapshotting will continue to write to the
snapshow COW volume, even after the volume has been marked read-only.
End result: snapshot failure.
This has actually been fixed in newer version of the lvm2 tool, but the
old tools still exist, and the breakage was reported both in the kernel
bugzilla and in the Debian bugzilla:
https://bugzilla.kernel.org/show_bug.cgi?id=200439
https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=900442
The lvm2 fix is here
https://sourceware.org/git/?p=lvm2.git;a=commit;h=
a6fdb9d9d70f51c49ad11a87ab4243344e6701a3
but until everybody has updated to recent versions, we'll have to weaken
the "never write to read-only partitions" check. It now allows the
write to happen, but causes a warning, something like this:
generic_make_request: Trying to write to read-only block-device dm-3 (partno X)
Modules linked in: nf_tables xt_cgroup xt_owner kvm_intel iwlmvm kvm irqbypass iwlwifi
CPU: 1 PID: 77 Comm: kworker/1:1 Not tainted 4.17.9-gentoo #3
Hardware name: LENOVO 20B6A019RT/20B6A019RT, BIOS GJET91WW (2.41 ) 09/21/2016
Workqueue: ksnaphd do_metadata
RIP: 0010:generic_make_request_checks+0x4ac/0x600
...
Call Trace:
generic_make_request+0x64/0x400
submit_bio+0x6c/0x140
dispatch_io+0x287/0x430
sync_io+0xc3/0x120
dm_io+0x1f8/0x220
do_metadata+0x1d/0x30
process_one_work+0x1b9/0x3e0
worker_thread+0x2b/0x3c0
kthread+0x113/0x130
ret_from_fork+0x35/0x40
Note that this is a "revert" in behavior only. I'm leaving alone the
actual code cleanups in commit
721c7fc701c7, but letting the previously
uncaught request go through with a warning instead of stopping it.
Fixes:
721c7fc701c7 ("block: fail op_is_write() requests to read-only partitions")
Reported-and-tested-by: WGH <wgh@torlan.ru>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Ilya Dryomov <idryomov@gmail.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Zdenek Kabelac <zkabelac@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dmitry Safonov [Sun, 5 Aug 2018 00:35:53 +0000 (01:35 +0100)]
netlink: Don't shift on 64 for ngroups
It's legal to have 64 groups for netlink_sock.
As user-supplied nladdr->nl_groups is __u32, it's possible to subscribe
only to first 32 groups.
The check for correctness of .bind() userspace supplied parameter
is done by applying mask made from ngroups shift. Which broke Android
as they have 64 groups and the shift for mask resulted in an overflow.
Fixes:
61f4b23769f0 ("netlink: Don't shift with UB on nlk->ngroups")
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: netdev@vger.kernel.org
Cc: stable@vger.kernel.org
Reported-and-Tested-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sun, 5 Aug 2018 00:51:55 +0000 (17:51 -0700)]
Merge git://git./pub/scm/linux/kernel/git/bpf/bpf
Daniel Borkmann says:
====================
pull-request: bpf 2018-08-05
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix bpftool percpu_array dump by using correct roundup to next
multiple of 8 for the value size, from Yonghong.
2) Fix in AF_XDP's __xsk_rcv_zc() to not returning frames back to
allocator since driver will recycle frame anyway in case of an
error, from Jakub.
3) Fix up BPF test_lwt_seg6local test cases to final iproute2
syntax, from Mathieu.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun [Fri, 3 Aug 2018 08:38:33 +0000 (10:38 +0200)]
net/smc: no cursor update send in state SMC_INIT
If a writer blocked condition is received without data, the current
consumer cursor is immediately sent. Servers could already receive this
condition in state SMC_INIT without finished tx-setup. This patch
avoids sending a consumer cursor update in this case.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kees Cook [Fri, 3 Aug 2018 19:52:58 +0000 (12:52 -0700)]
jfs: Fix usercopy whitelist for inline inode data
Bart Massey reported what turned out to be a usercopy whitelist false
positive in JFS when symlink contents exceeded 128 bytes. The inline
inode data (i_inline) is actually designed to overflow into the "extended
area" following it (i_inline_ea) when needed. So the whitelist needed to
be expanded to include both i_inline and i_inline_ea (the whole size
of which is calculated internally using IDATASIZE, 256, instead of
sizeof(i_inline), 128).
$ cd /mnt/jfs
$ touch $(perl -e 'print "B" x 250')
$ ln -s B* b
$ ls -l >/dev/null
[ 249.436410] Bad or missing usercopy whitelist? Kernel memory exposure attempt detected from SLUB object 'jfs_ip' (offset 616, size 250)!
Reported-by: Bart Massey <bart.massey@gmail.com>
Fixes:
8d2704d382a9 ("jfs: Define usercopy region in jfs_ip slab cache")
Cc: Dave Kleikamp <shaggy@kernel.org>
Cc: jfs-discussion@lists.sourceforge.net
Cc: stable@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Linus Torvalds [Fri, 3 Aug 2018 20:43:59 +0000 (13:43 -0700)]
Merge tag 'for-linus' of git://git./virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"Two vmx bugfixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
kvm: x86: vmx: fix vpid leak
KVM: vmx: use local variable for current_vmptr when emulating VMPTRST
Guillaume Nault [Fri, 3 Aug 2018 15:00:11 +0000 (17:00 +0200)]
l2tp: fix missing refcount drop in pppol2tp_tunnel_ioctl()
If 'session' is not NULL and is not a PPP pseudo-wire, then we fail to
drop the reference taken by l2tp_session_get().
Fixes:
ecd012e45ab5 ("l2tp: filter out non-PPP sessions in pppol2tp_tunnel_ioctl()")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 3 Aug 2018 19:28:02 +0000 (12:28 -0700)]
Merge branch 'mlxsw-Fix-ACL-actions-error-condition-handling'
Ido Schimmel says:
====================
mlxsw: Fix ACL actions error condition handling
Nir says:
Two issues were lately noticed within mlxsw ACL actions error condition
handling. The first patch deals with conflicting actions such as:
# tc filter add dev swp49 parent ffff: \
protocol ip pref 10 flower skip_sw dst_ip 192.168.101.1 \
action goto chain 100 \
action mirred egress redirect dev swp4
The second action will never execute, however SW model allows this
configuration, while the mlxsw driver cannot allow for it as it
implements actions in sets of up to three actions per set with a single
termination marking. Conflicting actions create a contradiction over
this single marking and thus cannot be configured. The fix replaces a
misplaced warning with an error code to be returned.
Patches 2-4 fix a condition of duplicate destruction of resources. Some
actions require allocation of specific resource prior to setting the
action itself. On error condition this resource was destroyed twice,
leading to a crash when using mirror action, and to a redundant
destruction in other cases, since for error condition rule destruction
also takes care of resource destruction. In order to fix this state a
symmetry in behavior is added and resource destruction also takes care
of removing the resource from rule's resource list.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Nir Dotan [Fri, 3 Aug 2018 12:57:44 +0000 (15:57 +0300)]
mlxsw: core_acl_flex_actions: Remove redundant mirror resource destruction
In previous patch mlxsw_afa_resource_del() was added to avoid a duplicate
resource detruction scenario.
For mirror actions, such duplicate destruction leads to a crash as in:
# tc qdisc add dev swp49 ingress
# tc filter add dev swp49 parent ffff: \
protocol ip chain 100 pref 10 \
flower skip_sw dst_ip 192.168.101.1 action drop
# tc filter add dev swp49 parent ffff: \
protocol ip pref 10 \
flower skip_sw dst_ip 192.168.101.1 action goto chain 100 \
action mirred egress mirror dev swp4
Therefore add a call to mlxsw_afa_resource_del() in
mlxsw_afa_mirror_destroy() in order to clear that resource
from rule's resources.
Fixes:
d0d13c1858a1 ("mlxsw: spectrum_acl: Add support for mirror action")
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nir Dotan [Fri, 3 Aug 2018 12:57:43 +0000 (15:57 +0300)]
mlxsw: core_acl_flex_actions: Remove redundant counter destruction
Each tc flower rule uses a hidden count action. As counter resource may
not be available due to limited HW resources, update _counter_create()
and _counter_destroy() pair to follow previously introduced symmetric
error condition handling, add a call to mlxsw_afa_resource_del() as part
of the counter resource destruction.
Fixes:
c18c1e186ba8 ("mlxsw: core: Make counter index allocated inside the action append")
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nir Dotan [Fri, 3 Aug 2018 12:57:42 +0000 (15:57 +0300)]
mlxsw: core_acl_flex_actions: Remove redundant resource destruction
Some ACL actions require the allocation of a separate resource
prior to applying the action itself. When facing an error condition
during the setup phase of the action, resource should be destroyed.
For such actions the destruction was done twice which is dangerous
and lead to a potential crash.
The destruction took place first upon error on action setup phase
and then as the rule was destroyed.
The following sequence generated a crash:
# tc qdisc add dev swp49 ingress
# tc filter add dev swp49 parent ffff: \
protocol ip chain 100 pref 10 \
flower skip_sw dst_ip 192.168.101.1 action drop
# tc filter add dev swp49 parent ffff: \
protocol ip pref 10 \
flower skip_sw dst_ip 192.168.101.1 action goto chain 100 \
action mirred egress mirror dev swp4
Therefore add mlxsw_afa_resource_del() as a complement of
mlxsw_afa_resource_add() to add symmetry to resource_list membership
handling. Call this from mlxsw_afa_fwd_entry_ref_destroy() to make the
_fwd_entry_ref_create() and _fwd_entry_ref_destroy() pair of calls a
NOP.
Fixes:
140ce421217e ("mlxsw: core: Convert fwd_entry_ref list to be generic per-block resource list")
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nir Dotan [Fri, 3 Aug 2018 12:57:41 +0000 (15:57 +0300)]
mlxsw: core_acl_flex_actions: Return error for conflicting actions
Spectrum switch ACL action set is built in groups of three actions
which may point to additional actions. A group holds a single record
which can be set as goto record for pointing at a following group
or can be set to mark the termination of the lookup. This is perfectly
adequate for handling a series of actions to be executed on a packet.
While the SW model allows configuration of conflicting actions
where it is clear that some actions will never execute, the mlxsw
driver must block such configurations as it creates a conflict
over the single terminate/goto record value.
For a conflicting actions configuration such as:
# tc filter add dev swp49 parent ffff: \
protocol ip pref 10 \
flower skip_sw dst_ip 192.168.101.1 \
action goto chain 100 \
action mirred egress mirror dev swp4
Where it is clear that the last action will never execute, the
mlxsw driver was issuing a warning instead of returning an error.
Therefore replace that warning with an error for this specific
case.
Fixes:
4cda7d8d7098 ("mlxsw: core: Introduce flexible actions support")
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Fri, 3 Aug 2018 17:49:47 +0000 (10:49 -0700)]
Merge tag 'for-linus' of git://git./linux/kernel/git/rdma/rdma
Pull rdma fix from Jason Gunthorpe:
"One bug for missing user input validation: refuse invalid port numbers
in the modify_qp system call"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/uverbs: Expand primary and alt AV port checks
Linus Torvalds [Fri, 3 Aug 2018 17:43:56 +0000 (10:43 -0700)]
Merge tag 'for-linus-
20180803' of git://git.kernel.dk/linux-block
Pull block fix from Jens Axboe:
"Just a single fix, from Ming, fixing a regression in this cycle where
the busy tag iteration was changed to only calling the callback
function for requests that are started. We really want all non-free
requests.
This fixes a boot regression on certain VM setups"
* tag 'for-linus-
20180803' of git://git.kernel.dk/linux-block:
blk-mq: fix blk_mq_tagset_busy_iter
Linus Torvalds [Fri, 3 Aug 2018 17:42:01 +0000 (10:42 -0700)]
Merge tag 'nfs-for-4.18-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfix from Trond Myklebust:
"Fix a NFSv4 file locking regression"
* tag 'nfs-for-4.18-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFSv4: Fix _nfs4_do_setlk()
Linus Torvalds [Fri, 3 Aug 2018 17:38:21 +0000 (10:38 -0700)]
Merge tag 'powerpc-4.18-5' of git://git./linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"One fix for a regression in a recent TLB flush optimisation, which
caused us to incorrectly not send TLB invalidations to coprocessors.
Thanks to Frederic Barrat, Nicholas Piggin, Vaibhav Jain"
* tag 'powerpc-4.18-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/64s/radix: Fix missing global invalidations when removing copro
Linus Torvalds [Fri, 3 Aug 2018 17:16:03 +0000 (10:16 -0700)]
Merge tag 'drm-fixes-2018-08-03' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Nothing too major at this late stage:
- adv7511: reset fix
- vc4: scaling fix
- two atomic core fixes
- one legacy core error handling fix
I had a bunch of driver fixes from hdlcd but I think I'll leave them
for -next at this point"
* tag 'drm-fixes-2018-08-03' of git://anongit.freedesktop.org/drm/drm:
drm/vc4: Reset ->{x, y}_scaling[1] when dealing with uniplanar formats
drm/atomic: Initialize variables in drm_atomic_helper_async_check() to make gcc happy
drm/atomic: Check old_plane_state->crtc in drm_atomic_helper_async_check()
drm: re-enable error handling
drm/bridge: adv7511: Reset registers on hotplug
Linus Torvalds [Fri, 3 Aug 2018 17:09:45 +0000 (10:09 -0700)]
Merge branch 'linus' of git://git./linux/kernel/git/herbert/crypto-2.6
Pull crypto fix from Herbert Xu:
"Fix a memory corruption in the padlock-aes driver"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: padlock-aes - Fix Nano workaround data corruption
Frederic Weisbecker [Fri, 3 Aug 2018 13:31:34 +0000 (15:31 +0200)]
nohz: Fix missing tick reprogram when interrupting an inline softirq
The full nohz tick is reprogrammed in irq_exit() only if the exit is not in
a nesting interrupt. This stands as an optimization: whether a hardirq or a
softirq is interrupted, the tick is going to be reprogrammed when necessary
at the end of the inner interrupt, with even potential new updates on the
timer queue.
When soft interrupts are interrupted, it's assumed that they are executing
on the tail of an interrupt return. In that case tick_nohz_irq_exit() is
called after softirq processing to take care of the tick reprogramming.
But the assumption is wrong: softirqs can be processed inline as well, ie:
outside of an interrupt, like in a call to local_bh_enable() or from
ksoftirqd.
Inline softirqs don't reprogram the tick once they are done, as opposed to
interrupt tail softirq processing. So if a tick interrupts an inline
softirq processing, the next timer will neither be reprogrammed from the
interrupting tick's irq_exit() nor after the interrupted softirq
processing. This situation may leave the tick unprogrammed while timers are
armed.
To fix this, simply keep reprogramming the tick even if a softirq has been
interrupted. That can be optimized further, but for now correctness is more
important.
Note that new timers enqueued in nohz_full mode after a softirq gets
interrupted will still be handled just fine through self-IPIs triggered by
the timer code.
Reported-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Cc: stable@vger.kernel.org # 4.14+
Link: https://lkml.kernel.org/r/1533303094-15855-1-git-send-email-frederic@kernel.org
Thomas Gleixner [Fri, 3 Aug 2018 12:44:59 +0000 (14:44 +0200)]
genirq: Make force irq threading setup more robust
The support of force threading interrupts which are set up with both a
primary and a threaded handler wreckaged the setup of regular requested
threaded interrupts (primary handler == NULL).
The reason is that it does not check whether the primary handler is set to
the default handler which wakes the handler thread. Instead it replaces the
thread handler with the primary handler as it would do with force threaded
interrupts which have been requested via request_irq(). So both the primary
and the thread handler become the same which then triggers the warnon that
the thread handler tries to wakeup a not configured secondary thread.
Fortunately this only happens when the driver omits the IRQF_ONESHOT flag
when requesting the threaded interrupt, which is normaly caught by the
sanity checks when force irq threading is disabled.
Fix it by skipping the force threading setup when a regular threaded
interrupt is requested. As a consequence the interrupt request which lacks
the IRQ_ONESHOT flag is rejected correctly instead of silently wreckaging
it.
Fixes:
2a1d3ab8986d ("genirq: Handle force threading of irqs with primary and thread handler")
Reported-by: Kurt Kanzenbach <kurt.kanzenbach@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Kurt Kanzenbach <kurt.kanzenbach@linutronix.de>
Cc: stable@vger.kernel.org
Mathieu Xhonneux [Wed, 1 Aug 2018 15:34:54 +0000 (15:34 +0000)]
selftests/bpf: update test_lwt_seg6local.sh according to iproute2
The shell file for test_lwt_seg6local contains an early iproute2 syntax
for installing a seg6local End.BPF route. iproute2 support for this
feature has recently been upstreamed, but with an additional keyword
required. This patch updates test_lwt_seg6local.sh to the definitive
iproute2 syntax
Signed-off-by: Mathieu Xhonneux <m.xhonneux@gmail.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Linus Torvalds [Thu, 2 Aug 2018 23:55:42 +0000 (16:55 -0700)]
Merge tag 'media/v4.18-3' of git://git./linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- a deadlock regression at vsp1 driver
- some Remote Controller fixes related to the new BPF filter logic
added on it for Kernel 4.18.
* tag 'media/v4.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: v4l: vsp1: Fix deadlock in VSPDL DRM pipelines
media: rc: read out of bounds if bpf reports high protocol number
media: bpf: ensure bpf program is freed on detach
media: rc: be less noisy when driver misbehaves
Linus Torvalds [Thu, 2 Aug 2018 23:52:50 +0000 (16:52 -0700)]
Merge tag 'arc-4.18-final' of git://git./linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
"Another batch of fixes for ARC, this time mainly DMA API rework
wreckage:
- Fix software managed DMA wreckage after rework in 4.17 [Euginey]
* missing cache flush
* SMP_CACHE_BYTES vs cache_line_size
- Fix allmodconfig build errors [Randy]
- Maintainer update for Mellanox (EZChip) NPS platform"
* tag 'arc-4.18-final' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
arc: fix type warnings in arc/mm/cache.c
arc: fix build errors in arc/include/asm/delay.h
arc: [plat-eznps] fix printk warning in arc/plat-eznps/mtm.c
arc: [plat-eznps] fix data type errors in platform headers
ARC: [plat-eznps] Add missing struct nps_host_reg_aux_dpc
ARC: add SMP_CACHE_BYTES value validate
ARC: dma [non-IOC] setup SMP_CACHE_BYTES and cache_line_size
ARC: dma [non IOC]: fix arc_dma_sync_single_for_(device|cpu)
ARC: Add Ofer Levi as plat-eznps maintainer
Linus Torvalds [Thu, 2 Aug 2018 23:41:59 +0000 (16:41 -0700)]
Merge branch 'akpm' (patches from Andrew)
Merge misc fixes from Andrew Morton:
"3 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
userfaultfd: remove uffd flags from vma->vm_flags if UFFD_EVENT_FORK fails
ipc/shm.c add ->pagesize function to shm_vm_ops
memcg: remove memcg_cgroup::id from IDR on mem_cgroup_css_alloc() failure
Mike Rapoport [Thu, 2 Aug 2018 22:36:09 +0000 (15:36 -0700)]
userfaultfd: remove uffd flags from vma->vm_flags if UFFD_EVENT_FORK fails
The fix in commit
0cbb4b4f4c44 ("userfaultfd: clear the
vma->vm_userfaultfd_ctx if UFFD_EVENT_FORK fails") cleared the
vma->vm_userfaultfd_ctx but kept userfaultfd flags in vma->vm_flags
that were copied from the parent process VMA.
As the result, there is an inconsistency between the values of
vma->vm_userfaultfd_ctx.ctx and vma->vm_flags which triggers BUG_ON
in userfaultfd_release().
Clearing the uffd flags from vma->vm_flags in case of UFFD_EVENT_FORK
failure resolves the issue.
Link: http://lkml.kernel.org/r/1532931975-25473-1-git-send-email-rppt@linux.vnet.ibm.com
Fixes:
0cbb4b4f4c44 ("userfaultfd: clear the vma->vm_userfaultfd_ctx if UFFD_EVENT_FORK fails")
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Reported-by: syzbot+121be635a7a35ddb7dcb@syzkaller.appspotmail.com
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Eric Biggers <ebiggers3@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jane Chu [Thu, 2 Aug 2018 22:36:05 +0000 (15:36 -0700)]
ipc/shm.c add ->pagesize function to shm_vm_ops
Commit
05ea88608d4e ("mm, hugetlbfs: introduce ->pagesize() to
vm_operations_struct") adds a new ->pagesize() function to
hugetlb_vm_ops, intended to cover all hugetlbfs backed files.
With System V shared memory model, if "huge page" is specified, the
"shared memory" is backed by hugetlbfs files, but the mappings initiated
via shmget/shmat have their original vm_ops overwritten with shm_vm_ops,
so we need to add a ->pagesize function to shm_vm_ops. Otherwise,
vma_kernel_pagesize() returns PAGE_SIZE given a hugetlbfs backed vma,
result in below BUG:
fs/hugetlbfs/inode.c
443 if (unlikely(page_mapped(page))) {
444 BUG_ON(truncate_op);
resulting in
hugetlbfs: oracle (4592): Using mlock ulimits for SHM_HUGETLB is deprecated
------------[ cut here ]------------
kernel BUG at fs/hugetlbfs/inode.c:444!
Modules linked in: nfsv3 rpcsec_gss_krb5 nfsv4 ...
CPU: 35 PID: 5583 Comm: oracle_5583_sbt Not tainted 4.14.35-1829.el7uek.x86_64 #2
RIP: 0010:remove_inode_hugepages+0x3db/0x3e2
....
Call Trace:
hugetlbfs_evict_inode+0x1e/0x3e
evict+0xdb/0x1af
iput+0x1a2/0x1f7
dentry_unlink_inode+0xc6/0xf0
__dentry_kill+0xd8/0x18d
dput+0x1b5/0x1ed
__fput+0x18b/0x216
____fput+0xe/0x10
task_work_run+0x90/0xa7
exit_to_usermode_loop+0xdd/0x116
do_syscall_64+0x187/0x1ae
entry_SYSCALL_64_after_hwframe+0x150/0x0
[jane.chu@oracle.com: relocate comment]
Link: http://lkml.kernel.org/r/20180731044831.26036-1-jane.chu@oracle.com
Link: http://lkml.kernel.org/r/20180727211727.5020-1-jane.chu@oracle.com
Fixes:
05ea88608d4e13 ("mm, hugetlbfs: introduce ->pagesize() to vm_operations_struct")
Signed-off-by: Jane Chu <jane.chu@oracle.com>
Suggested-by: Mike Kravetz <mike.kravetz@oracle.com>
Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com>
Acked-by: Davidlohr Bueso <dave@stgolabs.net>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Jérôme Glisse <jglisse@redhat.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kirill Tkhai [Thu, 2 Aug 2018 22:36:01 +0000 (15:36 -0700)]
memcg: remove memcg_cgroup::id from IDR on mem_cgroup_css_alloc() failure
In case of memcg_online_kmem() failure, memcg_cgroup::id remains hashed
in mem_cgroup_idr even after memcg memory is freed. This leads to leak
of ID in mem_cgroup_idr.
This patch adds removal into mem_cgroup_css_alloc(), which fixes the
problem. For better readability, it adds a generic helper which is used
in mem_cgroup_alloc() and mem_cgroup_id_put_many() as well.
Link: http://lkml.kernel.org/r/152354470916.22460.14397070748001974638.stgit@localhost.localdomain
Fixes
73f576c04b94 ("mm: memcontrol: fix cgroup creation failure after many small jobs")
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Vladimir Davydov <vdavydov.dev@gmail.com>
Cc: Michal Hocko <mhocko@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Colin Ian King [Wed, 1 Aug 2018 17:22:41 +0000 (18:22 +0100)]
drivers: net: lmc: fix case value for target abort error
Current value for a target abort error is 0x010, however, this value
should in fact be 0x002. As it stands, the range of error is 0..7 so
it is currently never being detected. This bug has been in the driver
since the early 2.6.12 days (or before).
Detected by CoverityScan, CID#744290 ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ming Lei [Thu, 2 Aug 2018 17:49:37 +0000 (01:49 +0800)]
blk-mq: fix blk_mq_tagset_busy_iter
Commit
d250bf4e776ff09d5("blk-mq: only iterate over inflight requests
in blk_mq_tagset_busy_iter") uses 'blk_mq_rq_state(rq) == MQ_RQ_IN_FLIGHT'
to replace 'blk_mq_request_started(req)', this way is wrong, and causes
lots of test system hang during booting.
Fix the issue by using blk_mq_request_started(req) inside bt_tags_iter().
Fixes:
d250bf4e776ff09d5 ("blk-mq: only iterate over inflight requests in blk_mq_tagset_busy_iter")
Cc: Josef Bacik <josef@toxicpanda.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Mark Brown <broonie@kernel.org>
Cc: Matt Hart <matthew.hart@linaro.org>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: John Garry <john.garry@huawei.com>
Cc: Hannes Reinecke <hare@suse.com>,
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>,
Cc: James Bottomley <James.Bottomley@hansenpartnership.com>
Cc: linux-scsi@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Reported-by: Mark Brown <broonie@kernel.org>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Eric Sandeen [Thu, 2 Aug 2018 20:09:27 +0000 (13:09 -0700)]
fs: fix iomap_bmap position calculation
The position calculation in iomap_bmap() shifts bno the wrong way,
so we don't progress properly and end up re-mapping block zero
over and over, yielding an unchanging physical block range as the
logical block advances:
# filefrag -Be file
ext: logical_offset: physical_offset: length: expected: flags:
0: 0.. 0: 21.. 21: 1: merged
1: 1.. 1: 21.. 21: 1: 22: merged
Discontinuity: Block 1 is at 21 (was 22)
2: 2.. 2: 21.. 21: 1: 22: merged
Discontinuity: Block 2 is at 21 (was 22)
3: 3.. 3: 21.. 21: 1: 22: merged
This breaks the FIBMAP interface for anyone using it (XFS), which
in turn breaks LILO, zipl, etc.
Bug-actually-spotted-by: Darrick J. Wong <darrick.wong@oracle.com>
Fixes:
89eb1906a953 ("iomap: add an iomap-based bmap implementation")
Cc: stable@vger.kernel.org
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Linus Torvalds [Thu, 2 Aug 2018 17:59:19 +0000 (10:59 -0700)]
Merge tag 'pci-v4.18-fixes-5' of git://git./linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- Fix integer overflow in new mobiveil driver (Dan Carpenter)
- Fix race during NVMe removal/rescan (Hari Vyas)
* tag 'pci-v4.18-fixes-5' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Fix is_added/is_busmaster race condition
PCI: mobiveil: Avoid integer overflow in IB_WIN_SIZE
Maninder Singh [Thu, 2 Aug 2018 09:57:27 +0000 (15:27 +0530)]
selftest/net: fix protocol family to work for IPv4.
use actual protocol family passed by user rather than hardcoded
AF_INTE6 to cerate sockets.
current code is not working for IPv4.
Signed-off-by: Maninder Singh <maninder1.s@samsung.com>
Signed-off-by: Vaneet Narang <v.narang@samsung.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 2 Aug 2018 17:21:49 +0000 (10:21 -0700)]
Merge tag 'arm64-fixes' of git://git./linux/kernel/git/arm64/linux
Pull arm64 regression fix from Will Deacon:
"Ard found a nasty arm64 regression in 4.18 where the AES ghash/gcm
code doesn't notify the kernel about its use of the vector registers,
therefore potentially corrupting live user state.
The fix is straightforward and Herbert agreed for it to go via arm64"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
crypto/arm64: aes-ce-gcm - add missing kernel_neon_begin/end pair
Linus Torvalds [Thu, 2 Aug 2018 17:12:02 +0000 (10:12 -0700)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
"Fixes keep trickling in:
1) Various IP fragmentation memory limit hardening changes from Eric
Dumazet.
2) Revert ipv6 metrics leak change, it causes more problems than it
fixes for now.
3) Fix WoL regression in stmmac driver, from Jose Abreu.
4) Netlink socket spectre v1 gadget fix, from Jeremy Cline"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
Revert "net/ipv6: fix metrics leak"
rxrpc: Fix user call ID check in rxrpc_service_prealloc_one
net: dsa: Do not suspend/resume closed slave_dev
netlink: Fix spectre v1 gadget in netlink_create()
Documentation: dpaa2: Use correct heading adornment
net: stmmac: Fix WoL for PCI-based setups
bonding: avoid lockdep confusion in bond_get_stats()
enic: do not call enic_change_mtu in enic_probe
ipv4: frags: handle possible skb truesize change
inet: frag: enforce memory limits earlier
net/mlx5e: IPoIB, Set the netdevice sw mtu in ipoib enhanced flow
net/mlx5e: Fix null pointer access when setting MTU of vport representor
net/mlx5e: Set port trust mode to PCP as default
net/mlx5e: E-Switch, Initialize eswitch only if eswitch manager
net: dsa: mv88e6xxx: Fix SERDES support on
88E6141/6341
brcmfmac: fix regression in parsing NVRAM for multiple devices
iwlwifi: add more card IDs for 9000 series
Phillip Lougher [Thu, 2 Aug 2018 15:45:15 +0000 (16:45 +0100)]
Squashfs: Compute expected length from inode size rather than block length
Previously in squashfs_readpage() when copying data into the page
cache, it used the length of the datablock read from the filesystem
(after decompression). However, if the filesystem has been corrupted
this data block may be short, which will leave pages unfilled.
The fix for this is to compute the expected number of bytes to copy
from the inode size, and use this to detect if the block is short.
Signed-off-by: Phillip Lougher <phillip@squashfs.org.uk>
Tested-by: Willy Tarreau <w@1wt.eu>
Cc: Анатолий Тросиненко <anatoly.trosinenko@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 2 Aug 2018 15:43:35 +0000 (08:43 -0700)]
squashfs: more metadata hardening
The squashfs fragment reading code doesn't actually verify that the
fragment is inside the fragment table. The end result _is_ verified to
be inside the image when actually reading the fragment data, but before
that is done, we may end up taking a page fault because the fragment
table itself might not even exist.
Another report from Anatoly and his endless squashfs image fuzzing.
Reported-by: Анатолий Тросиненко <anatoly.trosinenko@gmail.com>
Acked-by:: Phillip Lougher <phillip.lougher@gmail.com>,
Cc: Willy Tarreau <w@1wt.eu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kirill A. Shutemov [Wed, 1 Aug 2018 13:32:25 +0000 (16:32 +0300)]
x86/boot/compressed/64: Validate trampoline placement against E820
There were two report of boot failure cased by trampoline placed into
a reserved memory region. It can happen on machines that don't report
EBDA correctly.
Fix the problem by re-validating the found address against the E820 table.
If the address is in a reserved area, find the next usable region below the
initial address.
Fixes:
3548e131ec6a ("x86/boot/compressed/64: Find a place for 32-bit trampoline")
Reported-by: Dmitry Malkin <d.malkin@real-time-systems.com>
Reported-by: youling 257 <youling257@gmail.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Link: https://lkml.kernel.org/r/20180801133225.38121-1-kirill.shutemov@linux.intel.com
David S. Miller [Thu, 2 Aug 2018 04:32:30 +0000 (21:32 -0700)]
Revert "net/ipv6: fix metrics leak"
This reverts commit
df18b50448fab1dff093731dfd0e25e77e1afcd1.
This change causes other problems and use-after-free situations as
found by syzbot.
Signed-off-by: David S. Miller <davem@davemloft.net>
Trond Myklebust [Mon, 30 Jul 2018 02:21:22 +0000 (22:21 -0400)]
NFSv4: Fix _nfs4_do_setlk()
The patch to fix the case where a lock request was interrupted ended up
changing default handling of errors such as NFS4ERR_DENIED and caused the
client to immediately resend the lock request. Let's do a partial revert
of that request so that the default is now to exit, but change the way
we handle resends to take into account the fact that the user may have
interrupted the request.
Reported-by: Kenneth Johansson <ken@kenjo.org>
Fixes:
a3cf9bca2ace ("NFSv4: Don't add a new lock on an interrupted wait..")
Cc: Benjamin Coddington <bcodding@redhat.com>
Cc: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Linus Torvalds [Wed, 1 Aug 2018 22:01:26 +0000 (15:01 -0700)]
Merge branch 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM fix from Russell King:
"Just a single fix this time around for recent binutils causing build
problems when generating Thumb-2 code"
* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8781/1: Fix Thumb-2 syscall return for binutils 2.29+
Linus Torvalds [Wed, 1 Aug 2018 20:43:38 +0000 (13:43 -0700)]
mm: do not initialize TLB stack vma's with vma_init()
Commit
2c4541e24c55 ("mm: use vma_init() to initialize VMAs on stack and
data segments") tried to initialize various left-over ad-hoc vma's
"properly", but actually made things worse for the temporary vma's used
for TLB flushing.
vma_init() doesn't actually initialize all of the vma, just a few
fields, so doing something like
- struct vm_area_struct vma = { .vm_mm = tlb->mm, };
+ struct vm_area_struct vma;
+
+ vma_init(&vma, tlb->mm);
was actually very bad: instead of having a nicely initialized vma with
every field but "vm_mm" zeroed, you'd have an entirely uninitialized vma
with only a couple of fields initialized. And they weren't even fields
that the code in question mostly cared about.
The flush_tlb_range() function takes a "struct vma" rather than a
"struct mm_struct", because a few architectures actually care about what
kind of range it is - being able to only do an ITLB flush if it's a
range that doesn't have data accesses enabled, for example. And all the
normal users already have the vma for doing the range invalidation.
But a few people want to call flush_tlb_range() with a range they just
made up, so they also end up using a made-up vma. x86 just has a
special "flush_tlb_mm_range()" function for this, but other
architectures (arm and ia64) do the "use fake vma" thing instead, and
thus got caught up in the vma_init() changes.
At the same time, the TLB flushing code really doesn't care about most
other fields in the vma, so vma_init() is just unnecessary and
pointless.
This fixes things by having an explicit "this is just an initializer for
the TLB flush" initializer macro, which is used by the arm/arm64/ia64
people who mis-use this interface with just a dummy vma.
Fixes:
2c4541e24c55 ("mm: use vma_init() to initialize VMAs on stack and data segments")
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Kirill Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hugh Dickins [Wed, 1 Aug 2018 18:31:52 +0000 (11:31 -0700)]
mm: delete historical BUG from zap_pmd_range()
Delete the old VM_BUG_ON_VMA() from zap_pmd_range(), which asserted
that mmap_sem must be held when splitting an "anonymous" vma there.
Whether that's still strictly true nowadays is not entirely clear,
but the danger of sometimes crashing on the BUG is now fairly clear.
Even with the new stricter rules for anonymous vma marking, the
condition it checks for can possible trigger. Commit
44960f2a7b63
("staging: ashmem: Fix SIGBUS crash when traversing mmaped ashmem
pages") is good, and originally I thought it was safe from that
VM_BUG_ON_VMA(), because the /dev/ashmem fd exposed to the user is
disconnected from the vm_file in the vma, and madvise(,,MADV_REMOVE)
insists on VM_SHARED.
But after I read John's earlier mail, drawing attention to the
vfs_fallocate() in there: I may be wrong, and I don't know if Android
has THP in the config anyway, but it looks to me like an
unmap_mapping_range() from ashmem's vfs_fallocate() could hit precisely
the VM_BUG_ON_VMA(), once it's vma_is_anonymous().
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Kirill Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
YueHaibing [Wed, 1 Aug 2018 12:27:23 +0000 (13:27 +0100)]
rxrpc: Fix user call ID check in rxrpc_service_prealloc_one
There just check the user call ID isn't already in use, hence should
compare user_call_ID with xcall->user_call_ID, which is current
node's user_call_ID.
Fixes:
540b1c48c37a ("rxrpc: Fix deadlock between call creation and sendmsg/recvmsg")
Suggested-by: David Howells <dhowells@redhat.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 1 Aug 2018 18:43:13 +0000 (11:43 -0700)]
Merge tag 'mmc-v4.18-rc5' of git://git./linux/kernel/git/ulfh/mmc
Pull MMC fix from Ulf Hansson:
"MMC host: mxcmmc: Fix build error for powerpc"
* tag 'mmc-v4.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: mxcmmc: Fix missing parentheses and brace
Linus Torvalds [Wed, 1 Aug 2018 18:35:12 +0000 (11:35 -0700)]
Merge tag 'pm-urgent-4.18' of git://git./linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix the scope of a recent intel_pstate driver optimization used
incorrectly on some systems due to processor identification ambiguity
and fix a few issues in the turbostat utility, including three recent
regressions.
Specifics:
- Use ACPI FADT preferred PM Profile to distinguish Skylake desktop
processors from some server ones with the same model number in
order to limit the scope of the recent IO-wait boost optimization
to servers, as intended (Srinivas Pandruvada).
- Fix several issues in the turbostat utility:
* Fix the -S option on 1-CPU systems (Len Brown).
* Fix computations using incorrect processor core counts (Artem
Bityutskiy).
* Fix the x2apic debug message (Len Brown).
* Fix logical node enumeration to allow for non-sequential
physical nodes (Prarit Bhargava).
* Fix reported family on modern AMD processors (Calvin Walton).
* Clarify the RAPL column information in the man page (Len Brown)"
* tag 'pm-urgent-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: intel_pstate: Limit the scope of HWP dynamic boost platforms
tools/power turbostat: version 18.07.27
tools/power turbostat: Read extended processor family from CPUID
tools/power turbostat: Fix logical node enumeration to allow for non-sequential physical nodes
tools/power turbostat: fix x2apic debug message output file
tools/power turbostat: fix bogus summary values
tools/power turbostat: fix -S on UP systems
tools/power turbostat: Update turbostat(8) RAPL throttling column description
Linus Torvalds [Wed, 1 Aug 2018 17:38:43 +0000 (10:38 -0700)]
squashfs metadata 2: electric boogaloo
Anatoly continues to find issues with fuzzed squashfs images.
This time, corrupt, missing, or undersized data for the page filling
wasn't checked for, because the squashfs_{copy,read}_cache() functions
did the squashfs_copy_data() call without checking the resulting data
size.
Which could result in the page cache pages being incompletely filled in,
and no error indication to the user space reading garbage data.
So make a helper function for the "fill in pages" case, because the
exact same incomplete sequence existed in two places.
[ I should have made a squashfs branch for these things, but I didn't
intend to start doing them in the first place.
My historical connection through cramfs is why I got into looking at
these issues at all, and every time I (continue to) think it's a
one-off.
Because _this_ time is always the last time. Right? - Linus ]
Reported-by: Anatoly Trosinenko <anatoly.trosinenko@gmail.com>
Tested-by: Willy Tarreau <w@1wt.eu>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Phillip Lougher <phillip@squashfs.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
John Stultz [Tue, 31 Jul 2018 17:17:04 +0000 (10:17 -0700)]
staging: ashmem: Fix SIGBUS crash when traversing mmaped ashmem pages
Amit Pundir and Youling in parallel reported crashes with recent
mainline kernels running Android:
F DEBUG : *** *** *** *** *** *** *** *** *** *** *** *** *** *** *** ***
F DEBUG : Build fingerprint: 'Android/db410c32_only/db410c32_only:Q/OC-MR1/102:userdebug/test-key
F DEBUG : Revision: '0'
F DEBUG : ABI: 'arm'
F DEBUG : pid: 2261, tid: 2261, name: zygote >>> zygote <<<
F DEBUG : signal 7 (SIGBUS), code 2 (BUS_ADRERR), fault addr 0xec00008
... <snip> ...
F DEBUG : backtrace:
F DEBUG : #00 pc
00001c04 /system/lib/libc.so (memset+48)
F DEBUG : #01 pc
0010c513 /system/lib/libart.so (create_mspace_with_base+82)
F DEBUG : #02 pc
0015c601 /system/lib/libart.so (art::gc::space::DlMallocSpace::CreateMspace(void*, unsigned int, unsigned int)+40)
F DEBUG : #03 pc
0015c3ed /system/lib/libart.so (art::gc::space::DlMallocSpace::CreateFromMemMap(art::MemMap*, std::__1::basic_string<char, std::__ 1::char_traits<char>, std::__1::allocator<char>> const&, unsigned int, unsigned int, unsigned int, unsigned int, bool)+36)
...
This was bisected back to commit
bfd40eaff5ab ("mm: fix
vma_is_anonymous() false-positives").
create_mspace_with_base() in the trace above, utilizes ashmem, and with
ashmem, for shared mappings we use shmem_zero_setup(), which sets the
vma->vm_ops to &shmem_vm_ops. But for private ashmem mappings nothing
sets the vma->vm_ops.
Looking at the problematic patch, it seems to add a requirement that one
call vma_set_anonymous() on a vma, otherwise the dummy_vm_ops will be
used. Using the dummy_vm_ops seem to triggger SIGBUS when traversing
unmapped pages.
Thus, this patch adds a call to vma_set_anonymous() for ashmem private
mappings and seems to avoid the reported problem.
Fixes:
bfd40eaff5ab ("mm: fix vma_is_anonymous() false-positives")
Cc: Kirill Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Joel Fernandes <joelaf@google.com>
Cc: Colin Cross <ccross@google.com>
Cc: Matthew Wilcox <willy@infradead.org>
Reported-by: Amit Pundir <amit.pundir@linaro.org>
Reported-by: Youling 257 <youling257@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Wed, 1 Aug 2018 16:57:50 +0000 (09:57 -0700)]
ia64: mark special ia64 memory areas anonymous
Commit
bfd40eaff5ab ("mm: fix vma_is_anonymous() false-positives") made
newly allocated vma's have a dummy vm_ops field so that they wouldn't be
mistaken for anonymous mappings, and if you wanted an anonymous vma you
had to explicitly say so by calling "vma_set_anonymous()" on it.
However, it missed the two special vmas that ia64 processes have: the
register backing store and the NaT page. So they wouldn't actually act
like anonymous ranges, and page faults on them caused a SIGBUS rather
than the creation of a new anon page in them.
That obviously will make any ia64 binary very unhappy indeed, and the
boot fails early.
Fixes:
bfd40eaff5ab ("mm: fix vma_is_anonymous() false-positives")
Reported-by: Tony Luck <tony.luck@intel.com>
Cc: Kirill Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: John Stultz <john.stultz@linaro.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Florian Fainelli [Wed, 1 Aug 2018 00:12:52 +0000 (17:12 -0700)]
net: dsa: Do not suspend/resume closed slave_dev
If a DSA slave network device was previously disabled, there is no need
to suspend or resume it.
Fixes:
2446254915a7 ("net: dsa: allow switch drivers to implement suspend/resume hooks")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeremy Cline [Tue, 31 Jul 2018 21:13:16 +0000 (21:13 +0000)]
netlink: Fix spectre v1 gadget in netlink_create()
'protocol' is a user-controlled value, so sanitize it after the bounds
check to avoid using it for speculative out-of-bounds access to arrays
indexed by it.
This addresses the following accesses detected with the help of smatch:
* net/netlink/af_netlink.c:654 __netlink_create() warn: potential
spectre issue 'nlk_cb_mutex_keys' [w]
* net/netlink/af_netlink.c:654 __netlink_create() warn: potential
spectre issue 'nlk_cb_mutex_key_strings' [w]
* net/netlink/af_netlink.c:685 netlink_create() warn: potential spectre
issue 'nl_table' [w] (local cap)
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Jeremy Cline <jcline@redhat.com>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ioana Ciornei [Tue, 31 Jul 2018 15:45:53 +0000 (10:45 -0500)]
Documentation: dpaa2: Use correct heading adornment
Add overline heading adornment to document title in order to comply
with kernel doc requirements.
Fixes:
60b9131 staging: fsl-mc: Convert documentation to rst format
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu [Tue, 31 Jul 2018 14:08:20 +0000 (15:08 +0100)]
net: stmmac: Fix WoL for PCI-based setups
WoL won't work in PCI-based setups because we are not saving the PCI EP
state before entering suspend state and not allowing D3 wake.
Fix this by using a wrapper around stmmac_{suspend/resume} which
correctly sets the PCI EP state.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 31 Jul 2018 13:30:54 +0000 (06:30 -0700)]
bonding: avoid lockdep confusion in bond_get_stats()
syzbot found that the following sequence produces a LOCKDEP splat [1]
ip link add bond10 type bond
ip link add bond11 type bond
ip link set bond11 master bond10
To fix this, we can use the already provided nest_level.
This patch also provides correct nesting for dev->addr_list_lock
[1]
WARNING: possible recursive locking detected
4.18.0-rc6+ #167 Not tainted
--------------------------------------------
syz-executor751/4439 is trying to acquire lock:
(____ptrval____) (&(&bond->stats_lock)->rlock){+.+.}, at: spin_lock include/linux/spinlock.h:310 [inline]
(____ptrval____) (&(&bond->stats_lock)->rlock){+.+.}, at: bond_get_stats+0xb4/0x560 drivers/net/bonding/bond_main.c:3426
but task is already holding lock:
(____ptrval____) (&(&bond->stats_lock)->rlock){+.+.}, at: spin_lock include/linux/spinlock.h:310 [inline]
(____ptrval____) (&(&bond->stats_lock)->rlock){+.+.}, at: bond_get_stats+0xb4/0x560 drivers/net/bonding/bond_main.c:3426
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&(&bond->stats_lock)->rlock);
lock(&(&bond->stats_lock)->rlock);
*** DEADLOCK ***
May be due to missing lock nesting notation
3 locks held by syz-executor751/4439:
#0: (____ptrval____) (rtnl_mutex){+.+.}, at: rtnl_lock+0x17/0x20 net/core/rtnetlink.c:77
#1: (____ptrval____) (&(&bond->stats_lock)->rlock){+.+.}, at: spin_lock include/linux/spinlock.h:310 [inline]
#1: (____ptrval____) (&(&bond->stats_lock)->rlock){+.+.}, at: bond_get_stats+0xb4/0x560 drivers/net/bonding/bond_main.c:3426
#2: (____ptrval____) (rcu_read_lock){....}, at: bond_get_stats+0x0/0x560 include/linux/compiler.h:215
stack backtrace:
CPU: 0 PID: 4439 Comm: syz-executor751 Not tainted 4.18.0-rc6+ #167
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x1c9/0x2b4 lib/dump_stack.c:113
print_deadlock_bug kernel/locking/lockdep.c:1765 [inline]
check_deadlock kernel/locking/lockdep.c:1809 [inline]
validate_chain kernel/locking/lockdep.c:2405 [inline]
__lock_acquire.cold.64+0x1fb/0x486 kernel/locking/lockdep.c:3435
lock_acquire+0x1e4/0x540 kernel/locking/lockdep.c:3924
__raw_spin_lock include/linux/spinlock_api_smp.h:142 [inline]
_raw_spin_lock+0x2a/0x40 kernel/locking/spinlock.c:144
spin_lock include/linux/spinlock.h:310 [inline]
bond_get_stats+0xb4/0x560 drivers/net/bonding/bond_main.c:3426
dev_get_stats+0x10f/0x470 net/core/dev.c:8316
bond_get_stats+0x232/0x560 drivers/net/bonding/bond_main.c:3432
dev_get_stats+0x10f/0x470 net/core/dev.c:8316
rtnl_fill_stats+0x4d/0xac0 net/core/rtnetlink.c:1169
rtnl_fill_ifinfo+0x1aa6/0x3fb0 net/core/rtnetlink.c:1611
rtmsg_ifinfo_build_skb+0xc8/0x190 net/core/rtnetlink.c:3268
rtmsg_ifinfo_event.part.30+0x45/0xe0 net/core/rtnetlink.c:3300
rtmsg_ifinfo_event net/core/rtnetlink.c:3297 [inline]
rtnetlink_event+0x144/0x170 net/core/rtnetlink.c:4716
notifier_call_chain+0x180/0x390 kernel/notifier.c:93
__raw_notifier_call_chain kernel/notifier.c:394 [inline]
raw_notifier_call_chain+0x2d/0x40 kernel/notifier.c:401
call_netdevice_notifiers_info+0x3f/0x90 net/core/dev.c:1735
call_netdevice_notifiers net/core/dev.c:1753 [inline]
netdev_features_change net/core/dev.c:1321 [inline]
netdev_change_features+0xb3/0x110 net/core/dev.c:7759
bond_compute_features.isra.47+0x585/0xa50 drivers/net/bonding/bond_main.c:1120
bond_enslave+0x1b25/0x5da0 drivers/net/bonding/bond_main.c:1755
bond_do_ioctl+0x7cb/0xae0 drivers/net/bonding/bond_main.c:3528
dev_ifsioc+0x43c/0xb30 net/core/dev_ioctl.c:327
dev_ioctl+0x1b5/0xcc0 net/core/dev_ioctl.c:493
sock_do_ioctl+0x1d3/0x3e0 net/socket.c:992
sock_ioctl+0x30d/0x680 net/socket.c:1093
vfs_ioctl fs/ioctl.c:46 [inline]
file_ioctl fs/ioctl.c:500 [inline]
do_vfs_ioctl+0x1de/0x1720 fs/ioctl.c:684
ksys_ioctl+0xa9/0xd0 fs/ioctl.c:701
__do_sys_ioctl fs/ioctl.c:708 [inline]
__se_sys_ioctl fs/ioctl.c:706 [inline]
__x64_sys_ioctl+0x73/0xb0 fs/ioctl.c:706
do_syscall_64+0x1b9/0x820 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x440859
Code: e8 2c af 02 00 48 83 c4 18 c3 0f 1f 80 00 00 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 3b 10 fc ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:
00007ffc51a92878 EFLAGS:
00000213 ORIG_RAX:
0000000000000010
RAX:
ffffffffffffffda RBX:
0000000000000000 RCX:
0000000000440859
RDX:
0000000020000040 RSI:
0000000000008990 RDI:
0000000000000003
RBP:
0000000000000000 R08:
00000000004002c8 R09:
00000000004002c8
R10:
00000000022d5880 R11:
0000000000000213 R12:
0000000000007390
R13:
0000000000401db0 R14:
0000000000000000 R15:
0000000000000000
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Frederic Barrat [Tue, 31 Jul 2018 13:24:52 +0000 (15:24 +0200)]
powerpc/64s/radix: Fix missing global invalidations when removing copro
With the optimizations for TLB invalidation from commit
0cef77c7798a
("powerpc/64s/radix: flush remote CPUs out of single-threaded
mm_cpumask"), the scope of a TLBI (global vs. local) can now be
influenced by the value of the 'copros' counter of the memory context.
When calling mm_context_remove_copro(), the 'copros' counter is
decremented first before flushing. It may have the unintended side
effect of sending local TLBIs when we explicitly need global
invalidations in this case. Thus breaking any nMMU user in a bad and
unpredictable way.
Fix it by flushing first, before updating the 'copros' counter, so
that invalidations will be global.
Fixes:
0cef77c7798a ("powerpc/64s/radix: flush remote CPUs out of single-threaded mm_cpumask")
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Tested-by: Vaibhav Jain <vaibhav@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Rafael J. Wysocki [Wed, 1 Aug 2018 09:07:04 +0000 (11:07 +0200)]
Merge branch 'pm-tools'
Merge turbostat utility fixes for final 4.18:
- Fix the -S option on 1-CPU systems.
- Fix computations using incorrect processor core counts.
- Fix the x2apic debug message.
- Fix logical node enumeration to allow for non-sequential physical nodes.
- Fix reported family on modern AMD processors.
- Clarify the RAPL column information in the man page.
* pm-tools:
tools/power turbostat: version 18.07.27
tools/power turbostat: Read extended processor family from CPUID
tools/power turbostat: Fix logical node enumeration to allow for non-sequential physical nodes
tools/power turbostat: fix x2apic debug message output file
tools/power turbostat: fix bogus summary values
tools/power turbostat: fix -S on UP systems
tools/power turbostat: Update turbostat(8) RAPL throttling column description
Dave Airlie [Tue, 31 Jul 2018 22:54:27 +0000 (08:54 +1000)]
Merge tag 'drm-misc-fixes-2018-07-27' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
drm-misc-fixes pull request for v4.18-rc7:
- Small fixes to drm_atomic_helper_async_check(). (bbrezillon)
- Fix error handling in drm_legacy_addctx(). (Nicholas)
- Handle register reset on hotplug in adv7511. (seanpaul)
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/90e0e966-bce5-15a4-286a-eda908788b03@linux.intel.com
Govindarajulu Varadarajan [Mon, 30 Jul 2018 16:56:54 +0000 (09:56 -0700)]
enic: do not call enic_change_mtu in enic_probe
In commit
ab123fe071c9 ("enic: handle mtu change for vf properly")
ASSERT_RTNL() is added to _enic_change_mtu() to prevent it from being
called without rtnl held. enic_probe() calls enic_change_mtu()
without rtnl held. At this point netdev is not registered yet.
Remove call to enic_change_mtu and assign the mtu to netdev->mtu.
Fixes:
ab123fe071c9 ("enic: handle mtu change for vf properly")
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 31 Jul 2018 04:50:29 +0000 (21:50 -0700)]
ipv4: frags: handle possible skb truesize change
ip_frag_queue() might call pskb_pull() on one skb that
is already in the fragment queue.
We need to take care of possible truesize change, or we
might have an imbalance of the netns frags memory usage.
IPv6 is immune to this bug, because RFC5722, Section 4,
amended by Errata ID 3089 states :
When reassembling an IPv6 datagram, if
one or more its constituent fragments is determined to be an
overlapping fragment, the entire datagram (and any constituent
fragments) MUST be silently discarded.
Fixes:
158f323b9868 ("net: adjust skb->truesize in pskb_expand_head()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Tue, 31 Jul 2018 03:09:11 +0000 (20:09 -0700)]
inet: frag: enforce memory limits earlier
We currently check current frags memory usage only when
a new frag queue is created. This allows attackers to first
consume the memory budget (default : 4 MB) creating thousands
of frag queues, then sending tiny skbs to exceed high_thresh
limit by 2 to 3 order of magnitude.
Note that before commit
648700f76b03 ("inet: frags: use rhashtables
for reassembly units"), work queue could be starved under DOS,
getting no cpu cycles.
After commit
648700f76b03, only the per frag queue timer can eventually
remove an incomplete frag queue and its skbs.
Fixes:
b13d3cbfb8e8 ("inet: frag: move eviction of queues to work queue")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Jann Horn <jannh@google.com>
Cc: Florian Westphal <fw@strlen.de>
Cc: Peter Oskolkov <posk@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 31 Jul 2018 21:34:45 +0000 (14:34 -0700)]
Merge tag 'mlx5-fixes-2018-07-31' of git://git./linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2018-07-31
The following series includes four mlx5 fixes.
Please pull and let me know if there's any problem.
For -stable v4.14
net/mlx5e: E-Switch, Initialize eswitch only if eswitch manager
For -stable v4.16
net/mlx5e: Set port trust mode to PCP as default
For -stable v4.17
net/mlx5e: IPoIB, Set the netdevice sw mtu in ipoib enhanced flow
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Tue, 31 Jul 2018 20:17:46 +0000 (13:17 -0700)]
Merge tag 'audit-pr-
20180731' of git://git./linux/kernel/git/pcmoore/audit
Pull audit fix from Paul Moore:
"A single small audit fix to guard against memory allocation failures
when logging information about a kernel module load.
It's small, easy to understand, and self-contained; while nothing is
zero risk, this should be pretty low"
* tag 'audit-pr-
20180731' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit:
audit: fix potential null dereference 'context->module.name'
Anna-Maria Gleixner [Tue, 31 Jul 2018 16:13:58 +0000 (18:13 +0200)]
nohz: Fix local_timer_softirq_pending()
local_timer_softirq_pending() checks whether the timer softirq is
pending with: local_softirq_pending() & TIMER_SOFTIRQ.
This is wrong because TIMER_SOFTIRQ is the softirq number and not a
bitmask. So the test checks for the wrong bit.
Use BIT(TIMER_SOFTIRQ) instead.
Fixes:
5d62c183f9e9 ("nohz: Prevent a timer interrupt storm in tick_nohz_stop_sched_tick()")
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Daniel Bristot de Oliveira <bristot@redhat.com>
Acked-by: Frederic Weisbecker <frederic@kernel.org>
Cc: bigeasy@linutronix.de
Cc: peterz@infradead.org
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20180731161358.29472-1-anna-maria@linutronix.de
Feras Daoud [Sun, 15 Jul 2018 10:59:36 +0000 (13:59 +0300)]
net/mlx5e: IPoIB, Set the netdevice sw mtu in ipoib enhanced flow
After introduction of the cited commit, mlx5e_build_nic_params
receives the netdevice mtu in order to set the sw_mtu of mlx5e_params.
For enhanced IPoIB, the netdevice mtu is not set in this stage,
therefore, the initial sw_mtu equals zero. As a result, the hw_mtu
of the receive queue will be calculated incorrectly causing traffic
issues.
To fix this issue, query for port mtu before building the nic params.
Fixes:
472a1e44b349 ("net/mlx5e: Save MTU in channels params")
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Adi Nissim [Tue, 5 Jun 2018 08:32:11 +0000 (11:32 +0300)]
net/mlx5e: Fix null pointer access when setting MTU of vport representor
MTU helper function is used by both conventional mlx5e
instances (PF/VF) and the eswitch representors. The representor
shouldn't change the nic vport context MTU, the VF is responsible for
that. Therefore set_mtu_cb has a null value when changing the
representor MTU.
Fixes:
250a42b6a764 ("net/mlx5e: Support configurable MTU for vport representors")
Signed-off-by: Adi Nissim <adin@mellanox.com>
Reviewed-by: Yevgeny Kliteynik <kliteyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Or Gerlitz [Thu, 19 Jul 2018 16:17:00 +0000 (16:17 +0000)]
net/mlx5e: Set port trust mode to PCP as default
The hairpin offload code has dependency on the trust mode being PCP.
Hence we should set PCP as the default for handling cases where we are
disallowed to read the trust mode from the FW, or failed to initialize it.
Fixes:
106be53b6b0a ('net/mlx5e: Set per priority hairpin pairs')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Eli Cohen [Mon, 16 Jul 2018 08:49:27 +0000 (11:49 +0300)]
net/mlx5e: E-Switch, Initialize eswitch only if eswitch manager
Execute mlx5_eswitch_init() only if we have MLX5_ESWITCH_MANAGER
capabilities.
Do the same for mlx5_eswitch_cleanup().
Fixes:
a9f7705ffd66 ("net/mlx5: Unify vport manager capability check")
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Andrew Lunn [Tue, 31 Jul 2018 17:19:50 +0000 (19:19 +0200)]
net: dsa: mv88e6xxx: Fix SERDES support on
88E6141/6341
Version 1 of the patch adding SERDES support to the
88E6141/6341
correctly added the ops to the
88E6141/6341. However, by the time
version 3 was committed, the ops had moved to the
88E6085/6175. Put
them back where they belong.
Fixes:
5bafeb6e7e87 ("net: dsa: mv88e6xxx:
88E6141/6341 SERDES support")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 31 Jul 2018 17:33:43 +0000 (10:33 -0700)]
Merge tag 'wireless-drivers-for-davem-2018-07-31' of git://git./linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.18
Last set of fixes before 4.18 is released
iwlwifi
* add new IDs for cards already available on the market
brcmfmac
* fix a regression introduced in v4.17
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Tue, 31 Jul 2018 16:46:36 +0000 (09:46 -0700)]
Merge tag 'scsi-fixes' of git://git./linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Nine fixes, five in the qla2xxx driver, the most serious of which is
the uninitialized list head crash which can be observed in most
systems under a sufficiently loaded low memory environment.
The two sg fixes are minor but obvious and two target ones which seem
reasonable but not high impact"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: qla2xxx: Return error when TMF returns
scsi: qla2xxx: Fix ISP recovery on unload
scsi: qla2xxx: Fix driver unload by shutting down chip
scsi: qla2xxx: Fix NPIV deletion by calling wait_for_sess_deletion
scsi: qla2xxx: Fix unintialized List head crash
scsi: sg: update comment for blk_get_request()
scsi: sg: fix minor memory leak in error path
scsi: libiscsi: fix possible NULL pointer dereference in case of TMF
scsi: target: iscsi: cxgbit: fix max iso npdu calculation
Linus Torvalds [Tue, 31 Jul 2018 16:35:32 +0000 (09:35 -0700)]
Merge tag 'for_linus' of git://git./linux/kernel/git/mst/vhost
Pull virtio fixes from Michael Tsirkin:
"Some bugfixes that seem important and safe enough to merge at the last
minute"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio_balloon: fix another race between migration and ballooning
tools/virtio: add kmalloc_array stub
tools/virtio: add dma barrier stubs
Linus Torvalds [Tue, 31 Jul 2018 16:31:18 +0000 (09:31 -0700)]
Merge tag 'acpi-urgent-4.18' of git://git./linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These fix a recent ACPICA regression affecting control method
execution at the table level and an earlier hibernation regression in
the ACPI driver for Intel SoCs (LPSS) that was missed by a previous
fix in this cycle.
Specifics:
- Fix a recent ACPICA regression introduced by a previous fix that
caused control method execution at the table level to be mishandled
by mistake (Erik Schmauss).
- Fix a hibernation regression from the 4.15 cycle in the ACPI driver
for Intel SoCs (LPSS) that caused the platform firmware to be
confused during resume from hibernation by the driver's PM quirks
which was fixed for system-wide suspend/resume (ACPI S3) earlier in
this cycle, but that previous fix missed the hibernation (ACPI S4)
case (Rafael Wysocki)"
* tag 'acpi-urgent-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPICA: AML Parser: ignore control method status in module-level code
ACPI / LPSS: Avoid PM quirks on suspend and resume from hibernation
Hari Vyas [Tue, 3 Jul 2018 09:05:41 +0000 (14:35 +0530)]
PCI: Fix is_added/is_busmaster race condition
When a PCI device is detected, pdev->is_added is set to 1 and proc and
sysfs entries are created.
When the device is removed, pdev->is_added is checked for one and then
device is detached with clearing of proc and sys entries and at end,
pdev->is_added is set to 0.
is_added and is_busmaster are bit fields in pci_dev structure sharing same
memory location.
A strange issue was observed with multiple removal and rescan of a PCIe
NVMe device using sysfs commands where is_added flag was observed as zero
instead of one while removing device and proc,sys entries are not cleared.
This causes issue in later device addition with warning message
"proc_dir_entry" already registered.
Debugging revealed a race condition between the PCI core setting the
is_added bit in pci_bus_add_device() and the NVMe driver reset work-queue
setting the is_busmaster bit in pci_set_master(). As these fields are not
handled atomically, that clears the is_added bit.
Move the is_added bit to a separate private flag variable and use atomic
functions to set and retrieve the device addition state. This avoids the
race because is_added no longer shares a memory location with is_busmaster.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=200283
Signed-off-by: Hari Vyas <hari.vyas@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Ard Biesheuvel [Fri, 27 Jul 2018 12:59:15 +0000 (14:59 +0200)]
crypto/arm64: aes-ce-gcm - add missing kernel_neon_begin/end pair
Calling pmull_gcm_encrypt_block() requires kernel_neon_begin() and
kernel_neon_end() to be used since the routine touches the NEON
register file. Add the missing calls.
Also, since NEON register contents are not preserved outside of
a kernel mode NEON region, pass the key schedule array again.
Fixes:
7c50136a8aba ("crypto: arm64/aes-ghash - yield NEON after every ...")
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Srinivas Pandruvada [Mon, 30 Jul 2018 22:00:29 +0000 (15:00 -0700)]
cpufreq: intel_pstate: Limit the scope of HWP dynamic boost platforms
Dynamic boosting of HWP performance on IO wake showed significant
improvement to IO workloads. This series was intended for Skylake Xeon
platforms only and feature was enabled by default based on CPU model
number.
But some Xeon platforms reused the Skylake desktop CPU model number. This
caused some undesirable side effects to some graphics workloads. Since
they are heavily IO bound, the increase in CPU performance decreased the
power available for GPU to do its computing and hence decrease in graphics
benchmark performance.
For example on a Skylake desktop, GpuTest benchmark showed average FPS
reduction from 529 to 506.
This change makes sure that HWP boost feature is only enabled for Skylake
server platforms by using ACPI FADT preferred PM Profile. If some desktop
users wants to get benefit of boost, they can still enable boost from
intel_pstate sysfs attribute "hwp_dynamic_boost".
Fixes:
41ab43c9c89e (cpufreq: intel_pstate: enable boost for Skylake Xeon)
Link: https://bugs.freedesktop.org/show_bug.cgi?id=107410
Reported-by: Eero Tamminen <eero.t.tamminen@intel.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Reviewed-by: Francisco Jerez <currojerez@riseup.net>
Acked-by: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Rafael J. Wysocki [Tue, 31 Jul 2018 08:35:47 +0000 (10:35 +0200)]
Merge branch 'acpi-soc'
Merge a fix for hibernation regression in the ACPI driver for Intel
SoCs (LPSS).
* acpi-soc:
ACPI / LPSS: Avoid PM quirks on suspend and resume from hibernation
Ingo Molnar [Tue, 31 Jul 2018 05:43:48 +0000 (07:43 +0200)]
Merge tag 'perf-urgent-for-mingo-4.18-
20180730' of git://git./linux/kernel/git/acme/linux into perf/urgent
Pull perf/urgent fixes from Arnaldo Carvalho de Melo:
- Update the tools copy of several files, including perf_event.h,
powerpc's asm/unistd.h (new io_pgetevents syscall), bpf.h and
x86's memcpy_64.s (used in 'perf bench mem'), silencing the
respective warnings during the perf tools build.
- Fix the build on the alpine:edge distro.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Kan Liang [Mon, 30 Jul 2018 12:28:08 +0000 (08:28 -0400)]
perf/x86/intel/uncore: Fix hardcoded index of Broadwell extra PCI devices
Masayoshi Mizuma reported that a warning message is shown while a CPU is
hot-removed on Broadwell servers:
WARNING: CPU: 126 PID: 6 at arch/x86/events/intel/uncore.c:988
uncore_pci_remove+0x10b/0x150
Call Trace:
pci_device_remove+0x42/0xd0
device_release_driver_internal+0x148/0x220
pci_stop_bus_device+0x76/0xa0
pci_stop_root_bus+0x44/0x60
acpi_pci_root_remove+0x1f/0x80
acpi_bus_trim+0x57/0x90
acpi_bus_trim+0x2e/0x90
acpi_device_hotplug+0x2bc/0x4b0
acpi_hotplug_work_fn+0x1a/0x30
process_one_work+0x174/0x3a0
worker_thread+0x4c/0x3d0
kthread+0xf8/0x130
This bug was introduced by:
commit
15a3e845b01c ("perf/x86/intel/uncore: Fix SBOX support for Broadwell CPUs")
The index of "QPI Port 2 filter" was hardcode to 2, but this conflicts with the
index of "PCU.3" which is "HSWEP_PCI_PCU_3", which equals to 2 as well.
To fix the conflict, the hardcoded index needs to be cleaned up:
- introduce a new enumerator "BDX_PCI_QPI_PORT2_FILTER" for "QPI Port 2
filter" on Broadwell,
- increase UNCORE_EXTRA_PCI_DEV_MAX by one,
- clean up the hardcoded index.
Debugged-by: Masayoshi Mizuma <m.mizuma@jp.fujitsu.com>
Suggested-by: Ingo Molnar <mingo@kernel.org>
Reported-by: Masayoshi Mizuma <m.mizuma@jp.fujitsu.com>
Tested-by: Masayoshi Mizuma <m.mizuma@jp.fujitsu.com>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: msys.mizuma@gmail.com
Cc: stable@vger.kernel.org
Fixes:
15a3e845b01c ("perf/x86/intel/uncore: Fix SBOX support for Broadwell CPUs")
Link: http://lkml.kernel.org/r/1532953688-15008-1-git-send-email-kan.liang@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>