Merge tag 'renesas-dt-for-v4.18' of https://git./linux/kernel/git/horms/renesas into next/late

Renesas ARM Based SoC DT Updates for v4.18

* R-Mobile A1 (r8a7740) SoC
  - Describe CEU, IRQC, SYS-DMAC and USB devices
  - Cleanup for consistency with other Renesas SoCs and enhanced maintainability
* RZ/A1H (r7s72100) SoC
  - Describe CEU device
* R-Car Gen2, RZ/G1 and RZ/A1H SoCs
  - Add PMU device nodes
* RZ/A1H (r7s72100) SoC
  - Correct interrupt types
* R-Mobile APE6 (r8a73a4) APE4EVM board and SH-Mobile AG5 (sh73a0) SoC
  - Use generic disable-wp instead of now deprecated
    toshiba,mmc-wrprotect-disable property
* EMMA Mobile EV2 (emev2) and SH-Mobile AG5 (sh73a0) SoCs
  - Add missing interrupt-affinity to PMU
* R-Car H2 (r8a7790) and R-Mobile APE6 (r8a73a4) SoCs
  - Correct mask for GIC PPI interrupts
* R-Car H2 (r8a7790), M2-W (r8a7791), M2-N (r8a7793) and E2 (r8a7794) SoCs
  - Describe FDP1 instances
* R-Car Gen2 and RZ/G1 SoCs
  - Describe watchdog devices
  - For R-Car Gen2 this involves updating the SMP routine side as
    it is changed by a driver updated to allow watchdog device support

* Alt board for R-Car E2 (r8a7794) SoC
* RBoards for -Car Gen2 SoCs and kzm9d board for EMMA Mobile EV2 (emev2) SoC
* iW-RainboW-G23S board for RZ/G1C (r8a77470) SoC
  - Initial SoC and board support
  - Enable EtherAVB
  - Describe all SCIF devices
* Boards for R-Car Gen2 SoCs
  - Enable watchdog support
* Wheat board for V2H (r8a7792) SoC
  - Correct ADV7513 address usage

* tag 'renesas-dt-for-v4.18' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (69 commits)
  ARM: dts: r8a7740: Add CEU1
  ARM: dts: r8a7740: Add CEU0
  ARM: dts: r8a7745: Add PMU device node
  ARM: dts: r8a7743: Add PMU device node
  ARM: dts: r8a7794: Add PMU device node
  ARM: dts: r8a7793: Add PMU device node
  ARM: dts: r8a7792: Add PMU device node
  ARM: dts: r8a7791: Add PMU device node
  ARM: dts: r8a7790: Add PMU device nodes
  ARM: dts: r7s72100: Add PMU device node
  ARM: dts: r7s72100: Correct RTC interrupt types
  ARM: dts: r7s72100: Correct watchdog timer interrupt type
  ARM: dts: emev2: Add missing interrupt-affinity to PMU node
  ARM: dts: sh73a0: Add missing interrupt-affinity to PMU node
  ARM: dts: r8a73a4: Correct mask for GIC PPI interrupts
  ARM: dts: r8a7790: Correct mask for GIC PPI interrupts
  ARM: shmobile: r8a7794: alt: add EEPROM to DTS
  ARM: dts: kzm9d: Drop unnecessary address properties from gpio_keys node
  ARM: dts: silk: Drop unnecessary address properties from vin port node
  ARM: dts: alt: Drop unnecessary address properties from vin port node
  ...

Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'renesas-arm64-dt-for-v4.18' of https://git./linux/kernel/git/horms/renesas into next/late

Renesas ARM64 Based SoC DT Updates for v4.18

* Cleanups:
  - Correct whitespace
  - sort subnodes of the root and soc nodes
* R-Car M3-N (r8a77965) SoC
  - Describe MSIOF SPI, PWM, SDHI and I2C devices in DT
  - Add thermal support
* R-Car H3 (r8a7795) and R-Car M3-W (r8a7796) SoCs
  - Decrease temperature hysteresis
* R-Car H3 (r8a7795), M3-W (r8a7796) and M3-N (r8a77965) SoCs
  - Add address properties to rcar_sound port nodes
* R-Car H3 (r8a7795), M3-W (r8a7796) V3M (r8a77970) and D3 (r8a77995) SoCs
  - Enable IPMMU devices
* R-Car M3-N (r8a77965) and V3H (r8a77980) SoCs
  - Use sysc binding macros
  - Describe USB2 and USB3 devices in DT
* R-Car V3M (r8a77970) SoC
  - Add SMP Support
  - Correct IPMMU DS1 bit number
* R-Car V3H (r8a77980) SoC
  - Use CPG clock binding macros
* R-Car V3H (r8a77980) and V3M (r8a77970) SoCs
  - Disable EtherAVB
* R-Car D3 (r8a77995) SoC
  - Describe VIN4 in DT

* Ebisu board with R-Car E3 (r8a77990) SoC
  - Initial support
* Salvator-XS boards with R-Car H3 (r8a7795) SoC
  - Enable USB2.0 channel 3
* Salvator-X and Salvator-XS boards with M3-N (r8a77965) SoC
  - Enable DU
* Salvator-X and Salvator-XS boards with
  R-Car H3 (r8a7795), M3-W (r8a7796) and M3-N (r8a77965) SoCs
  - Enable nable VIN, CSI-2 and ADV7482
  - Add PMIC DDR Backup Power config
  - Add EEPROM
  - Enable HDMI Sound
* Salvator-X and Salvator-XS boards with
  R-Car H3 (r8a7795), M3-W (r8a7796) and M3-N (r8a77965) SoCs, and
  Draak board with R-Car D3 (r8a77995) SoC
  - Consistently name EtherAVB mdio pin group
* Ebisu board with R-Car E3 (r8a77990) SoC
  - Initial support: Memory, Main crystal, Serial console
  - Enable Ethernet
  - Revise PSCI node
  - Revise cache controller node
* V3HSK board with R-Car V3H (r8a77980) SoC
  - Initial board device tree
  - Enable PFC support and use for EtherAVB
* V3MSK board with R-Car V3M (r8a77970) SoC
  - Add DU/LVDS/HDMI support
  - Enable PFC for EtherAVB
* Condor board with R-Car V3H (r8a77980) SoC
  - Enable eMMC
  - Enable PFC support and use for EtherAVB and SCIF0
* Eagle board with R-Car V3M (r8a77970) SoC
  - Enable HDMI output
* Eagle board with R-Car V3M (r8a77970) SoC and
  Condor board with R-Car V3H (r8a77980) SoC
  - Enable CAN-FD

* tag 'renesas-arm64-dt-for-v4.18' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (102 commits)
  arm64: dts: renesas: salvator-common: Add ADV7482 support
  arm64: dts: renesas: salvator-common: enable VIN
  arm64: dts: renesas: r8a77970: add VIN and CSI-2 nodes
  arm64: dts: renesas: r8a77965: add VIN and CSI-2 nodes
  arm64: dts: renesas: r8a7796: add VIN and CSI-2 nodes
  arm64: dts: renesas: r8a7795-es1: add CSI-2 node
  arm64: dts: renesas: r8a7795: add VIN and CSI-2 nodes
  arm64: dts: renesas: r8a77965: add I2C support
  arm64: dts: renesas: r8a77990: ebisu: Enable EthernetAVB
  arm64: dts: renesas: r8a77990: Add EthernetAVB device nodes
  arm64: dts: renesas: r8a77990: Add GPIO device nodes
  arm64: dts: renesas: r8a77990: Add PFC device node
  arm64: dts: renesas: initial V3HSK board device tree
  arm64: dts: renesas: r8a77980: disable EtherAVB
  arm64: dts: renesas: r8a77970: disable EtherAVB
  arm64: dts: renesas: r8a77995: Add VIN4
  arm64: dts: renesas: r8a77980: add resets property to CAN-FD node
  arm64: dts: renesas: r8a77970: Add Cortex-A53 PMU node
  arm64: dts: renesas: r8a77970: Add secondary CA53 CPU core
  arm64: dts: renesas: r8a77965: Add SDHI device nodes
  ...

Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'qcom-drivers-for-4.18' of git://git./linux/kernel/git/agross/linux into next/late

Qualcomm ARM Based Driver Updates for v4.18

* Various SMEM updates/fixes
* Add qcom_smem_virt_to_phys SMEM API
* Update MAINTAINERS to include qcom_scm pattern
* Add Qualcomm Command DB driver
* Add Qualcomm SCM compatible for IPQ4019
* Add MSM8998 to smd-rpm compatible list
* Add Qualcomm GENI based QUP wrapper
* Fix Qualcomm QMI buffer sizing bug

* tag 'qcom-drivers-for-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
  soc: qcom: smem: introduce qcom_smem_virt_to_phys()
  soc: qcom: qmi: fix a buffer sizing bug
  MAINTAINERS: Update pattern for qcom_scm
  soc: Unconditionally include qcom Makefile
  soc: qcom: smem: check sooner in qcom_smem_set_global_partition()
  soc: qcom: smem: fix qcom_smem_set_global_partition()
  soc: qcom: smem: fix off-by-one error in qcom_smem_alloc_private()
  soc: qcom: smem: byte swap values properly
  soc: qcom: smem: return proper type for cached entry functions
  soc: qcom: smem: fix first cache entry calculation
  soc: qcom: cmd-db: Make endian-agnostic
  drivers: qcom: add command DB driver
  soc: qcom: Add GENI based QUP Wrapper driver
  soc: qcom: smd-rpm: Add msm8998 compatible
  firmware: qcom: scm: Add ipq4019 soc compatible

Signed-off-by: Olof Johansson <olof@lixom.net>

soc: qcom: smem: introduce qcom_smem_virt_to_phys()

Create function qcom_smem_virt_to_phys(), which returns the physical
address corresponding to a given SMEM item's virtual address.  This
feature is required for a driver that will soon be out for review.

Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

soc: qcom: qmi: fix a buffer sizing bug

In qmi_handle_init(), a buffer is allocated for to hold messages
received through the handle's socket.  Any "normal" messages
(expected by the caller) will have a header prepended, so the
buffer size is adjusted to accomodate that.

The buffer must also be of sufficient size to receive control
messages, so the size is increased if necessary to ensure these
will fit.

Unfortunately the calculation is done wrong, making it possible
for the calculated buffer size to be too small to hold a "normal"
message.  Specifically, if:

  recv_buf_size > sizeof(struct qrtr_ctrl_pkt) - sizeof(struct qmi_header)
AND
  recv_buf_size < sizeof(struct qrtr_ctrl_pkt)

the current logic will use sizeof(struct qrtr_ctrl_pkt) as the
receive buffer size, which is not enough to hold the maximum
"normal" message plus its header.  Currently this problem occurs
for (13 < recv_buf_size < 20).

This patch corrects this.

Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

MAINTAINERS: Update pattern for qcom_scm

Update pattern for qcom_scm, so that get_maintainer.pl will show the
correct maintainers + lists, not only for qcom_scm.c, but also for
the files: qcom_scm-32.c, qcom_scm-64.c, qcom_scm.h.

Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

soc: Unconditionally include qcom Makefile

Incoming Qualcomm changes for GENI, i2c [1], and cmd-db [2] are enabled
with COMPILE_TEST in drivers/soc/qcom. For this to work, the Makefile
in that directory has to be included unconditionally, rather than only
if ARCH_QCOM is enabled.

Example of the errors seen on allmodconfig with the GENI, i2c, and
cmd-db patches applied:

Kernel: arch/x86/boot/bzImage is ready  (#1)
ERROR: "geni_se_select_mode" [drivers/tty/serial/qcom_geni_serial.ko] undefined!
ERROR: "geni_se_init" [drivers/tty/serial/qcom_geni_serial.ko] undefined!
ERROR: "geni_se_config_packing" [drivers/tty/serial/qcom_geni_serial.ko] undefined!
ERROR: "geni_se_resources_on" [drivers/tty/serial/qcom_geni_serial.ko] undefined!
ERROR: "geni_se_resources_off" [drivers/tty/serial/qcom_geni_serial.ko] undefined!
ERROR: "geni_se_tx_dma_unprep" [drivers/i2c/busses/i2c-qcom-geni.ko] undefined!
ERROR: "geni_se_tx_dma_prep" [drivers/i2c/busses/i2c-qcom-geni.ko] undefined!
ERROR: "geni_se_rx_dma_unprep" [drivers/i2c/busses/i2c-qcom-geni.ko] undefined!
ERROR: "geni_se_rx_dma_prep" [drivers/i2c/busses/i2c-qcom-geni.ko] undefined!
ERROR: "geni_se_select_mode" [drivers/i2c/busses/i2c-qcom-geni.ko] undefined!
ERROR: "geni_se_config_packing" [drivers/i2c/busses/i2c-qcom-geni.ko] undefined!
ERROR: "geni_se_init" [drivers/i2c/busses/i2c-qcom-geni.ko] undefined!
ERROR: "geni_se_resources_off" [drivers/i2c/busses/i2c-qcom-geni.ko] undefined!
ERROR: "geni_se_resources_on" [drivers/i2c/busses/i2c-qcom-geni.ko] undefined!
make[1]: *** [scripts/Makefile.modpost:92: __modpost] Error 1
make: *** [Makefile:1237: modules] Error 2

[1] https://patchwork.ozlabs.org/cover/893437/
[2] https://lkml.org/lkml/2018/4/10/714

Signed-off-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

soc: qcom: smem: check sooner in qcom_smem_set_global_partition()

There's no sense in scanning the partition table again if we know
the global partition has already been discovered.  Check for a
non-null global_partition pointer in qcom_smem_set_global_partition()
immediately.

Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

soc: qcom: smem: fix qcom_smem_set_global_partition()

If there is at least one entry in the partition table, but no global
entry, the qcom_smem_set_global_partition() should return an error
just like it does if there are no partition table entries.

It turns out the function still returns an error in this case, but
it waits to do so until it has mistakenly treated the last entry in
the table as if it were the global entry found.

Fix the function to return immediately if no global entry is found
in the table.

Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

soc: qcom: smem: fix off-by-one error in qcom_smem_alloc_private()

It's OK if the space for a newly-allocated uncached entry actually
touches the free cached space boundary.  It's only a problem if it
would cross it.

Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

soc: qcom: smem: byte swap values properly

Two places report an error when a partition header is found to
not contain the right canary value.  The error messages do not
properly byte swap the host ids.  Fix this, and adjust the format
specificier to match the 16-bit unsigned data type.

Move the error handling for a bad canary value to the end of
qcom_smem_alloc_private().  This avoids some long lines, and
reduces the distraction of handling this unexpected problem.

Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

soc: qcom: smem: return proper type for cached entry functions

What phdr_to_last_uncached_entry() returns is the address of the
start of the free space following all allocated uncached entries.
It really doesn't refer to an actual (initialized) private entry
structure.   Similarly phdr_to_last_cached_entry() returns the
address of the end of free space, preceding the last allocated cache
entry.  Change both functions' return type to be pointer to void
to reflect this.

Meanwhile, phdr_to_first_cached_entry() really *does* point to a
private entry structure, so change its return type to reflect
this fact.

Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

soc: qcom: smem: fix first cache entry calculation

Cached items are found at the high end of an smem partition.  A
cached item's shared memory precedes the private entry structure
that describes it.

The address of the structure describing the first cached item should
be returned by phdr_to_first_cached_entry().  However the function
calculates the start address using the wrong structure size.

Fix this by computing the first item's entry structure address by
subtracting the size of a private entry structure rather than a
partition header structure.

Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

soc: qcom: cmd-db: Make endian-agnostic

This driver deals with memory that is stored in little-endian format.
Update the structures with the proper little-endian types and then
do the proper conversions when reading the fields. Note that we compare
the ids with a memcmp() because we already pad out the string 'id' field
to exactly 8 bytes with the strncpy() onto the stack.

Cc: Mahesh Sivasubramanian <msivasub@codeaurora.org>
Cc: Lina Iyer <ilina@codeaurora.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Evan Green <evgreen@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

drivers: qcom: add command DB driver

Command DB is a simple database in the shared memory of QCOM SoCs, that
provides information regarding shared resources. Some shared resources
in the SoC have properties that are probed dynamically at boot by the
remote processor. The information pertaining to the SoC and the platform
are made available in the shared memory. Drivers can query this
information using predefined strings.

Signed-off-by: Mahesh Sivasubramanian <msivasub@codeaurora.org>
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>

arm64: dts: renesas: salvator-common: Add ADV7482 support

The Salvator boards use an ADV7482 receiver for HDMI and CVBS inputs.

Provide ADV7482 node on the i2c4 bus, along with connectors for the
hdmi and cvbs inputs, and link to the csi20 and csi40 nodes as outputs.

Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ARM: dts: r8a7740: Add CEU1

Describe CEU1 peripheral for Renesas R-Mobile A1 R8A7740 Soc.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>

ARM: dts: r8a7740: Add CEU0

Describe CEU0 peripheral for Renesas R-Mobile A1 R8A7740 Soc.

Reported-by: Geert Uytterhoeven <geert@glider.be>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
[simon: dropped clock-names property]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: salvator-common: enable VIN

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a77970: add VIN and CSI-2 nodes

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a77965: add VIN and CSI-2 nodes

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a7796: add VIN and CSI-2 nodes

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a7795-es1: add CSI-2 node

Renesas H3 ES1.0 have one extra CSI-2 node, CSI21 which is not present
for later ES versions of H3.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a7795: add VIN and CSI-2 nodes

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a77965: add I2C support

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a77990: ebisu: Enable EthernetAVB

This patch enables EthernetAVB for r8a77990 Ebisu board.

Based on a patch from Takeshi Kihara <takeshi.kihara.df@renesas.com>

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a77990: Add EthernetAVB device nodes

This patch adds EthernetAVB node for r8a77990 (R-Car E3).

Based on a patch from Takeshi Kihara <takeshi.kihara.df@renesas.com>

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a77990: Add GPIO device nodes

This patch adds GPIO nodes for r8a77990 (R-Car E3).

Based on a patch from Takeshi Kihara <takeshi.kihara.df@renesas.com>

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
[simon: dropped use of deprecated "renesas,gpio-rcar"]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a77990: Add PFC device node

This patch adds PFC device node for r8a77990 (R-Car E3).

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: initial V3HSK board device tree

Add the initial device  tree for  the V3H Starter Kit board.
The board has 1 debug serial port (SCIF0); include support for it,
so that the serial console can work.

Based on the original (and large) patch by Vladimir Barinov.

Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a77980: disable EtherAVB

When adding the R8A77980 EtherAVB device I failed to notice that it does
not have the usual "status" property disabling the described devices in
anticipation that the board device trees enable the devices according to
their needs. This causes the EtherAVB driver to successfully probe despite
e.g. the needed pins not having been configured -- luckily, "eth<n>" device
can't be opened anyway...

Fixes: bf6f90832f81 ("arm64: dts: renesas: r8a77980: add EtherAVB support")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a77970: disable EtherAVB

When adding the R8A77970 EtherAVB device I failed to notice that it does
not have the usual "status" property disabling the described devices in
anticipation that the board device trees enable the devices according to
their needs. This causes the EtherAVB driver to successfully probe despite
e.g. the needed pins not having been configured -- luckily, "eth<n>" device
can't be opened anyway...

Fixes: bea2ab136eaa ("arm64: dts: renesas: r8a77970: add EtherAVB support")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a77995: Add VIN4

Describe VIN4 interface for R-Car D3 R8A77995 SoC.

Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
[simon: sorted node by bus address]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>

arm64: dts: renesas: r8a77980: add resets property to CAN-FD node

Add resets property to CAN-FD node to describe it in the reset topology of
on-SoC devices.  This allows to reset the CAN-FD device using the Reset
Controller API.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>

arm64: dts: renesas: r8a77970: Add Cortex-A53 PMU node

Enable the performance monitor unit for the Cortex-A53 cores on the
R-Car V3M (r8a77970) SoC.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a77970: Add secondary CA53 CPU core

Add a device node for the second Cortex-A53 CPU core on the Renesas
R-Car V3M (r8a77970) SoC, and adjust the interrupt delivery masks for
ARM Generic Interrupt Controller and Architectured Timer.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a77965: Add SDHI device nodes

Add SDHI nodes to the DT of the r8a77965 SoC.

Based on several similar patches of the R8A7796 device tree
by Simon Horman <horms+renesas@verge.net.au>.

Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: ulcb: Add PMIC DDR Backup Power config

On the R-Car Starter Kit Premier/Pro, all of the DDR0, DDR1, DDR0C, and
DDR1C power rails need to be kept powered when backup mode is enabled.
Reflect this in the "rohm,ddr-backup-power" property for the BD9571MWV
PMIC node.

The accessory power switch (SW8) is a momentary switch, hense specify
"rohm,rstbmode-pulse".

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: salvator-common: Add PMIC DDR Backup Power config

On Salvator-X(S), all of the DDR0, DDR1, DDR0C, and DDR1C power rails
need to be kept powered when backup mode is enabled.  Reflect this in
the "rohm,ddr-backup-power" property for the BD9571MWV PMIC node.

The accessory power switch (SW23) is a toggle switch, hence specify
"rohm,rstbmode-level".

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: ulcb: Add BD9571 PMIC

Add a device node for the ROHM BD9571MWV PMIC.

This was based on the example in the DT binding documentation, but using
IRQ0 instead of a GPIO interrupt, as that matches the schematics, and
because INTC-EX is a simpler block.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a77965: Correct whitespace

Add missing space after comma.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a7796: Correct whitespace

Add missing spaces after commas.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a7795: Correct whitespace

Add missing spaces after commas.
Replace 8 consecutive spaces by a TAB.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a7795: salvator-xs: enable USB2.0 host channel 3

This patch enables USB2.0 host channel 3 for r8a7795 with Salvator-XS.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a7795: salvator-xs: enable hsusb channel 3 node

This patch enables HS-USB channel3 node for r8a7795 with Salvator-XS.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a7795: salvator-xs: enable usb2_phy3 node

This patch enables usb2_phy3 node for r8a7795 with Salvator-XS.
You must change the SW31 to OFF-OFF-ON-ON-ON-ON on the board.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: salvator-common: add eeprom

Add the EEPROM found on Salvator-X and -XS boards for H3, M3-W, and M3-N
on the IIC_DVFS bus.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: condor: add CAN-FD support

Define the Condor board dependent part of the CAN-FD device node.

Based on the original (and large) patch by Vladimir Barinov.

Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a77980: add CAN-FD support

Define the generic R8A77980 part of the CAN-FD device node.

Based on the original (and large) patch by Vladimir Barinov.

Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
[simon: consistently use tabs for indentation]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: eagle: add CAN-FD support

Define the Eagle board dependent part of the CAN-FD device node.

Based on the original (and large) patch by Vladimir Barinov.

Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a77970: add CAN-FD support

Define the generic R8A77970 part of the CAN-FD device node.

Based on the original (and large) patch by Vladimir Barinov.

Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a77965: Add R-Car Gen3 thermal support

Based on previous work by Ryo Kataoka <ryo.kataoka.wt@renesas.com>.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
[simon: moved thermal node to preseve ordering of nodes by bus address]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a77965: use r8a77965-sysc binding definitions

Replace the hardcoded power domain indices by R8A77965_PD_* symbols.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
[simon: dropped hunk to include r8a77965-sysc.h which is already present]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a77980: use SYSC power domain macros

Now that the commit 7755b40d07a8 ("dt-bindings: power: add R8A77980 SYSC
power domain definitions") has hit Linus' tree, we can replace  the bare
numbers (we had to use to avoid a cross tree dependency) with these macro
definitions...

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a77980: use CPG core clock macros

Now that the commit 35b3c462dae1 ("dt-bindings: clock: add R8A77980 CPG
core clock definitions") has hit Linus' tree, we can replace the bare
numbers (we had to use to avoid a cross tree dependency) with these macro
definitions...

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a77965: Add address properties to rcar_sound port nodes

The rcar_sound port nodes have unit names and thus should have register
properties.

This is flagged by dtc as follows:
 # make dtbs W=1
 ...
 DTC     arch/arm64/boot/dts/renesas/r8a77965-salvator-x.dtb
arch/arm64/boot/dts/renesas/r8a77965-salvator-x.dtb: Warning (unit_address_vs_reg): /soc/sound@ec500000/ports/port@0: node has a unit name, but no reg property
 DTC     arch/arm64/boot/dts/renesas/r8a77965-salvator-xs.dtb
arch/arm64/boot/dts/renesas/r8a77965-salvator-xs.dtb: Warning (unit_address_vs_reg): /soc/sound@ec500000/ports/port@0: node has a unit name, but no reg property

Prior to this patch the port nodes only defined in board DTS files.
As the register properties are common this patch defines the port nodes
and provides register properties in the SoC DTS file.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>

arm64: dts: renesas: r8a7796: Add address properties to rcar_sound port nodes

The rcar_sound port nodes have unit names and thus should have register
properties.

This is flagged by dtc as follows:
 # make dtbs W=1
 ...
 DTC     arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dtb
 arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dtb: Warning (unit_address_vs_reg): /soc/sound@ec500000/ports/port@0: node has a unit name, but no reg property
 arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dtb: Warning (unit_address_vs_reg): /soc/sound@ec500000/ports/port@1: node has a unit name, but no reg property
 ...
 DTC     arch/arm64/boot/dts/renesas/r8a7796-salvator-xs.dtb
 arch/arm64/boot/dts/renesas/r8a7796-salvator-xs.dtb: Warning (unit_address_vs_reg): /soc/sound@ec500000/ports/port@0: node has a unit name, but no reg property
 arch/arm64/boot/dts/renesas/r8a7796-salvator-xs.dtb: Warning (unit_address_vs_reg): /soc/sound@ec500000/ports/port@1: node has a unit name, but no reg property

Prior to this patch the port nodes only defined in board DTS files.
As the register properties are common this patch defines the port nodes
and provides register properties in the SoC DTS file.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>

arm64: dts: renesas: r8a7795: Add address properties to rcar_sound port nodes

The rcar_sound port nodes have unit names and thus should have register
properties.

This is flagged by dtc as follows:
 # make dtbs W=1
 ...
 DTC     arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dtb
 arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dtb: Warning (unit_address_vs_reg): /soc/sound@ec500000/ports/port@0: node has a unit name, but no reg property
arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dtb: Warning (unit_address_vs_reg): /soc/sound@ec500000/ports/port@1: node has a unit name, but no reg property
arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dtb: Warning (unit_address_vs_reg): /soc/sound@ec500000/ports/port@2: node has a unit name, but no reg property
  ...
  DTC     arch/arm64/boot/dts/renesas/r8a7795-salvator-xs.dtb
arch/arm64/boot/dts/renesas/r8a7795-salvator-xs.dtb: Warning (unit_address_vs_reg): /soc/sound@ec500000/ports/port@0: node has a unit name, but no reg property
arch/arm64/boot/dts/renesas/r8a7795-salvator-xs.dtb: Warning (unit_address_vs_reg): /soc/sound@ec500000/ports/port@1: node has a unit name, but no reg property
arch/arm64/boot/dts/renesas/r8a7795-salvator-xs.dtb: Warning (unit_address_vs_reg): /soc/sound@ec500000/ports/port@2: node has a unit name, but no reg property
  DTC     arch/arm64/boot/dts/renesas/r8a7795-es1-salvator-x.dtb
arch/arm64/boot/dts/renesas/r8a7795-es1-salvator-x.dtb: Warning (unit_address_vs_reg): /soc/sound@ec500000/ports/port@0: node has a unit name, but no reg property
arch/arm64/boot/dts/renesas/r8a7795-es1-salvator-x.dtb: Warning (unit_address_vs_reg): /soc/sound@ec500000/ports/port@1: node has a unit name, but no reg property
arch/arm64/boot/dts/renesas/r8a7795-es1-salvator-x.dtb: Warning (unit_address_vs_reg): /soc/sound@ec500000/ports/port@2: node has a unit name, but no reg property

Prior to this patch the port nodes only defined in board DTS files.
As the register properties are common this patch defines the port nodes
and provides register properties in the SoC DTS file.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>

arm64: dts: renesas: v3msk: add DU/LVDS/HDMI support

Define the V3M Starter Kit board dependent part of the DU and LVDS device
nodes. Also add the device nodes for Thine THC63LVD1024 LVDS decoder and
Analog Devices ADV7511W HDMI transmitter...

Based on the original (and large) patch by Vladimir Barinov.

Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: condor: add eMMC support

Define the Condor board dependent part of the MMC0 (connected to eMMC chip)
device node along with the necessary voltage regulators...

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a77965-salvator-xs: Enable DU external clocks and HDMI

The DU1 external dot clock is provided by the fixed frequency clock
generator X21, while the DU0 and DU3 clocks are provided by the
programmable Versaclock6 clock generator.

Enable the clocks, and the HDMI encoder for the M3-N Salvator-XS, and
hook it up to the HDMI connector

Based on patches from Takeshi Kihara <takeshi.kihara.df@renesas.com>

Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a77965-salvator-x: Enable DU external clocks and HDMI

The DU1 external dot clock is provided by the fixed frequency clock
generator X21, while the DU0 and DU3 clocks are provided by the
programmable Versaclock5 clock generator.

Enable the clocks, and the HDMI encoder for the M3-N Salvator-X board
and hook it up to the HDMI connector.

Based on patches from Takeshi Kihara <takeshi.kihara.df@renesas.com>

Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a77965: Add HDMI encoder instance

Add the HDMI encoder to the R8A77965 DT in disabled state.

Based on a similar patch of the R8A7796 device tree
by Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>.

Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[Kieran: Rebase to top of tree]
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a77965: Populate the DU instance placeholder

The DU entity node has been previously added but only as a placeholder.
Populate the node with the properties to use the device.

Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a77965: Add VSP instances

The r8a77965 has 4 VSP instances.

Based on a similar patch of the R8A7796 device tree
by Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>.

Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[Kieran: Rebased to top of tree, fixed sort orders]
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a77965: Add FCPF and FCPV instances

The FCPs handle the interface between various IP cores and memory. Add
the instances related to the FDPs and VSP2s.

Based on a similar patch of the R8A7796 device tree
by Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>.

Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[Kieran: Rebase to top of tree]
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a77990: Revise the cache controller node

The cache controller node should not have unit-addresses and reg
properties. So, this patch removes them.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a77990: Revise the psci node

The basic support patch 9491a8b17530 ("arm64: dts: renesas: Add Renesas
R8A77990 SoC support") lacks the compatible "arm,psci-1.0" in the psci
node. So, this patch revises it.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a7795-es1: Enable IPMMU devices

Remove 'status = "disabled"' to make sure all IPMMU devices are enabled
in DT on the r8a7795 ES1.0 Soc.

This is a follow up for a patch by Magnus Damm for the
the r8a7795 ES2.0 and other R-Car Gen 3 SoCs.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a7796-salvator-x: enable HDMI sound

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Nguyen Viet Dung <nv-dung@jinso.co.jp>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a7795-salvator-x: enable HDMI sound

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Nguyen Viet Dung <nv-dung@jinso.co.jp>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a7796-salvator-xs: enable HDMI sound

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Nguyen Viet Dung <nv-dung@jinso.co.jp>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a7795-salvator-xs: enable HDMI sound

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Nguyen Viet Dung <nv-dung@jinso.co.jp>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a7795-es1-salvator-x: enable HDMI sound

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Nguyen Viet Dung <nv-dung@jinso.co.jp>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: salvator-common: use audio-graph-card for Sound

Current Sound is using simple-audio-card which can't support HDMI.
To use HDMI sound, we need to use audio-graph-card.
But, one note is that r8a7795 has 2 HDMI ports, but r8a7796 has 1.
Because of this mismatch, supporting HDMI on salvator-common is
impossible.
Thus, this patch exchange sound card to audio-graph-card and keep
supporting ak4613 as 1st sound node.
r8a7795/r8a7796 salvator-x{s} need to add HDMI sound individually.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Nguyen Viet Dung <nv-dung@jinso.co.jp>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a7796: add HDMI sound support

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Nguyen Viet Dung <nv-dung@jinso.co.jp>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a7795: add HDMI sound support

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Nguyen Viet Dung <nv-dung@jinso.co.jp>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a77980: add MMC support

Define the generic R8A77980 part of the MMC0 (SDHI2) device node.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: condor: add EtherAVB pins

Add the (previously omitted) EtherAVB pin data to the Condor board's
device tree.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: condor: add SCIF0 pins

Add the (previously omitted) SCIF0 pin data to the Condor board's
device tree.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a77980: add PFC support

Define the generic R8A77980 part of the PFC device node.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: v3msk: add EtherAVB pins

Add the (previously omitted) EtherAVB pin data to the V3M Starter Kit
board's device tree.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: eagle: add EtherAVB pins

Add the (previously omitted) EtherAVB pin data to the Eagle board's
device tree.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: ulcb: Rename EtherAVB "mdc" pin group to "mdio"

On other Renesas SoCs, the pin group for the MDIO bus is named "mdio"
instead of "mdc".  Fix the inconsistency, now the pinctrl drivers for
R-Car H3, M3-W, and M3-N have gained support for the traditional pin
group name.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: salvator-common: Rename EtherAVB "mdc" pin group to "mdio"

On other Renesas SoCs, the pin group for the MDIO bus is named "mdio"
instead of "mdc".  Fix the inconsistency, now the pinctrl drivers for
R-Car H3, M3-W, and M3-N have gained support for the traditional pin
group name.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: draak: Rename EtherAVB "mdc" pin group to "mdio"

On other Renesas SoCs, the pin group for the MDIO bus is named "mdio"
instead of "mdc".  Fix the inconsistency, now the pinctrl drivers for
R-Car H3, M3-W, and M3-N have gained support for the traditional pin
group name.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a77995: Enable IPMMU devices

Remove 'status = "disabled"' to make sure all IPMMU devices are enabled
in DT on the r8a77995 SoC.

Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
[simon: rebased]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a77970: Enable IPMMU devices

Remove 'status = "disabled"' to make sure all IPMMU devices are enabled
in DT on the r8a77970 SoC.

Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
[simon: rebased]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a7796: Enable IPMMU devices

Remove 'status = "disabled"' to make sure all IPMMU devices are enabled
in DT on the r8a7796 SoC.

Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a7795: Enable IPMMU devices

Remove 'status = "disabled"' to make sure all IPMMU devices are enabled
in DT on the r8a7795 SoC.

Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: Add Renesas Ebisu board support

Basic support for the Renesas Ebisu board based on R-Car E3:
  - Memory,
  - Main crystal,
  - Serial console,

Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[shimoda: rebase and add SPDX-License-Identifier]
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: Add Renesas R8A77990 SoC support

This patch adds basic support for the Renesas R-Car E3 (R8A77990) SoC:
  - PSCI
  - CPU (single)
  - Cache controller
  - Main clocks and controller
  - Interrupt controller
  - Timer
  - PMU
  - Reset controller
  - Product register
  - System controller
  - UART for console

Inspried by a patch by Takeshi Kihara in the BSP.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a77970: sort subnodes of the soc node

Sort subnodes of the soc node.
- The primary key is the bus address.
- The secondary key is the IP block.
- The tertiary key is the node name.

This is part of an ongoing effort to provide consistent node
order in the DT of Renesas SoCs to improve maintainability.

This should not have any run-time effect.

Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
[simon: rebased; move fcpvd0 to after vspd0]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a77965: sort subnodes of the soc node

Sort subnodes of the soc node.
- The primary key is the bus address.
- The secondary key is the IP block.
- The tertiary key is the node name.

This is part of an ongoing effort to provide consistent node
order in the DT of Renesas SoCs to improve maintainability.

This should not have any run-time effect.

Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a77965: sort subnodes of the root node

Sort subnodes of the root node alphanumerically.

This is part of an ongoing effort to provide consistent node
order in the DT of Renesas SoCs to improve maintainability.

This should not have any run-time effect.

Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a77995: sort subnodes of the soc node

Sort subnodes of the soc node.
- The primary key is the bus address.
- The secondary key is the IP block.
- The tertiary key is the node name.

This is part of an ongoing effort to provide consistent node
order in the DT of Renesas SoCs to improve maintainability.

This should not have any run-time effect.

Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a77995: sort subnodes of the root node

Sort subnodes of the root node alphanumerically.

This is part of an ongoing effort to provide consistent node
order in the DT of Renesas SoCs to improve maintainability.

This should not have any run-time effect.

Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: eagle: Enable HDMI output

Enable HDMI output on Renesas R-Car V3M Eagle board.

The HDMI output is enabled connecting the DU LVDS output to the
transparent LVDS converter THC63LVD1024, and successively routing its
RGB output to the ADV7511W HDMI encoder.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[for THC63LVD1024: ]
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a77970: add LVDS support

Define the generic R8A77970 part of the LVDS device node.

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

arm64: dts: renesas: r8a77970: add DU support

Define the generic R8A77970 part of the DU device node.

Based on the original (and large) patch by Daisuke Matsushita
<daisuke.matsushita.ns@hitachi.com>.

Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>