OSDN Git Service
Hsu, Kenny [Fri, 2 Dec 2011 16:48:26 +0000 (08:48 -0800)]
iwlwifi: add tm commands for sram reading by dumpit
Create new testmode commands and attributes to suppot
sram data reading. Because the amount of sram data
may exceed single skb packet size. Using the nl80211
dump it funtion to deliver sram data to userspace.
- IWL_TM_CMD_APP2DEV_READ_SRAM
- IWL_TM_CMD_APP2DEV_DUMP_SRAM
- IWL_TM_ATTR_SRAM_ADDR
- IWL_TM_ATTR_SRAM_SIZE
- IWL_TM_ATTR_SRAM_DUMP
Signed-off-by: Kenny Hsu <kenny.hsu@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mohammed Shafi Shajakhan [Thu, 1 Dec 2011 12:44:01 +0000 (18:14 +0530)]
ath9k: clarify max_streams for AR9462
max_streams for AR9462 is '2'. it does not fixes anything, but
improves the code readability
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mohammed Shafi Shajakhan [Thu, 1 Dec 2011 05:44:19 +0000 (11:14 +0530)]
ath9k_hw: sync to latest AR9462 INI
based on systems change to improve rx dynamic range,
and enables heavy clip for 5G HT40 MCS0 to improve
spectral mask power. also remove an unused function
declaration
Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Larry Finger [Wed, 30 Nov 2011 16:58:14 +0000 (10:58 -0600)]
rtl8192c: Do not log firmware load message unless actually done
A previous commit fixed a problem whereby the rtl8192c driver loaded the
firmware from disk many times; however, the log message was not moved.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Alexander Simon [Wed, 30 Nov 2011 15:56:34 +0000 (16:56 +0100)]
mac80211: Add HT operation modes for IBSS
The HT mode is set by iw (previous patchsets).
The interface is set into the specified HT mode.
HT mode and capabilities are announced in beacons.
If we add a station that uses HT also, the fastest matching HT mode will
be used for transmission. That means if we are using HT40+ and we add a station
running on HT40-, we would transfer at HT20.
If we join an IBSS with HT40, but the secondary channel is not
available, we will fall back into HT20 as well.
Allow frame aggregation to start in IBSS mode.
Signed-off-by: Alexander Simon <an.alexsimon@googlemail.com>
[siwu@hrz.tu-chemnitz.de: Updates]
* remove implicit channel_type enum assumptions
* use rate_control_rate_init() if channel type changed
* remove channel flags check
* activate HT IBSS feature support
* slightly reword commit message
* rebase on wireless-testing
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Simon Wunderlich [Wed, 30 Nov 2011 15:56:33 +0000 (16:56 +0100)]
mac80211: handle protection mode, RIFS and ADDBA for HT IBSS
* Follow 802.11n-2009 9.13.3.1 for protection mode and ADDBA
* Send ADDBA only to HT STAs - implement 11.5.1.1 partially
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Alexander Simon [Wed, 30 Nov 2011 15:56:32 +0000 (16:56 +0100)]
nl80211: Parse channel type attribute in an ibss join request
Prepare cfg80211 for IBSS HT:
* extend cfg80211 ibss struct with channel_type
* Check if extension channel can be used
* Export can_beacon_sec_chan for use in mac80211 (will be called
from ibss.c later).
Signed-off-by: Alexander Simon <an.alexsimon@googlemail.com>
[siwu@hrz.tu-chemnitz.de: Updates]
* fix cfg80211_can_beacon_ext_chan comment
* remove implicit channel_type enum assumptions
* remove radar channel flags check
* add HT IBSS feature flag
* reword commit message
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Thomas Meyer [Tue, 29 Nov 2011 21:08:00 +0000 (22:08 +0100)]
iwlegacy: Use kcalloc instead of kzalloc to allocate array
The advantage of kcalloc is, that will prevent integer overflows which could
result from the multiplication of number of elements and size and it is also
a bit nicer to read.
The semantic patch that makes this change is available
in https://lkml.org/lkml/2011/11/25/107
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Thomas Meyer [Tue, 29 Nov 2011 21:08:00 +0000 (22:08 +0100)]
rt2x00: Use kcalloc instead of kzalloc to allocate array
The advantage of kcalloc is, that will prevent integer overflows which could
result from the multiplication of number of elements and size and it is also
a bit nicer to read.
The semantic patch that makes this change is available
in https://lkml.org/lkml/2011/11/25/107
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Tue, 6 Dec 2011 21:02:05 +0000 (16:02 -0500)]
Merge branch 'master' of git://git./linux/kernel/git/padovan/bluetooth-next
Andrei Emeltchenko [Thu, 1 Dec 2011 12:33:28 +0000 (14:33 +0200)]
Bluetooth: trivial: correct check for LMP version
Make sure that code match exactly what comment says about pre 1.2
bluetooth version. Since this is HCI detail lmp_ver changed to hci_ver.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Andrei Emeltchenko [Thu, 1 Dec 2011 12:33:27 +0000 (14:33 +0200)]
Bluetooth: Remove magic bluetooth version numbers
Use bluetooth names instead of BT SIG assigned numbers
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Gustavo F. Padovan [Fri, 2 Dec 2011 23:26:25 +0000 (08:26 +0900)]
Merge branch 'master' of git://git./linux/kernel/git/padovan/bluetooth
Andrei Emeltchenko [Wed, 23 Nov 2011 09:23:34 +0000 (11:23 +0200)]
Bluetooth: Correct version check in hci_setup
Check for hci_ver instead of lmp_ver
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Cong Wang [Tue, 22 Nov 2011 01:32:57 +0000 (09:32 +0800)]
btusb: fix a memory leak in btusb_send_frame()
This patch fixes the following memory leak reported by kmemleak:
unreferenced object 0xffff880060a53840 (size 192):
comm "softirq", pid 0, jiffies
4320571771 (age 1406.569s)
hex dump (first 32 bytes):
01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<
ffffffff81138a1c>] create_object+0x187/0x28b
[<
ffffffff814be12e>] kmemleak_alloc+0x73/0x98
[<
ffffffff811289d3>] __kmalloc+0xfc/0x123
[<
ffffffff81386546>] usb_alloc_urb+0x1e/0x48
[<
ffffffffa0130274>] btusb_send_frame+0x86/0x385 [btusb]
[<
ffffffffa02d8230>] hci_send_frame+0xa0/0xa5 [bluetooth]
[<
ffffffffa02d8a4e>] hci_cmd_task+0xa0/0xfb [bluetooth]
[<
ffffffff81058548>] tasklet_action+0x8f/0xef
[<
ffffffff81058a4c>] __do_softirq+0xf4/0x1db
[<
ffffffff81058bb7>] run_ksoftirqd+0x84/0x129
[<
ffffffff8106f1c4>] kthread+0xa0/0xa8
[<
ffffffff814dd144>] kernel_thread_helper+0x4/0x10
[<
ffffffffffffffff>] 0xffffffffffffffff
The problem is that when inc_tx() returns non-zero, we forgot
to call usb_free_urb().
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: "Gustavo F. Padovan" <padovan@profusion.mobi>
Signed-off-by: WANG Cong <amwang@redhat.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
John W. Linville [Fri, 2 Dec 2011 20:44:03 +0000 (15:44 -0500)]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless
Conflicts:
drivers/net/wireless/iwlwifi/iwl-agn.c
drivers/net/wireless/libertas/cfg.c
Wey-Yi Guy [Fri, 2 Dec 2011 16:19:19 +0000 (08:19 -0800)]
iwlwifi: change the default behavior of watchdog timer
The current default watchdog timer is enabled, but we are seeing issues on
legacy devices. So change the default setting of watchdog timer to per
device based. But user still can use the "wd_disable" module parameter
to overwrite the system setting
Cc: stable@vger.kernel.org #3.0+
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 2 Dec 2011 16:19:18 +0000 (08:19 -0800)]
iwlwifi: do not re-configure HT40 after associated
The ht40 setting should not change after association unless channel switch
This fix a problem we are seeing which cause uCode assert because driver
sending invalid information and make uCode confuse
Here is the firmware assert message:
kernel: iwlagn 0000:03:00.0: Microcode SW error detected. Restarting 0x82000000.
kernel: iwlagn 0000:03:00.0: Loaded firmware version: 17.168.5.3 build 42301
kernel: iwlagn 0000:03:00.0: Start IWL Error Log Dump:
kernel: iwlagn 0000:03:00.0: Status: 0x000512E4, count: 6
kernel: iwlagn 0000:03:00.0: 0x00002078 | ADVANCED_SYSASSERT
kernel: iwlagn 0000:03:00.0: 0x00009514 | uPc
kernel: iwlagn 0000:03:00.0: 0x00009496 | branchlink1
kernel: iwlagn 0000:03:00.0: 0x00009496 | branchlink2
kernel: iwlagn 0000:03:00.0: 0x0000D1F2 | interruptlink1
kernel: iwlagn 0000:03:00.0: 0x00000000 | interruptlink2
kernel: iwlagn 0000:03:00.0: 0x01008035 | data1
kernel: iwlagn 0000:03:00.0: 0x0000C90F | data2
kernel: iwlagn 0000:03:00.0: 0x000005A7 | line
kernel: iwlagn 0000:03:00.0: 0x5080B520 | beacon time
kernel: iwlagn 0000:03:00.0: 0xCC515AE0 | tsf low
kernel: iwlagn 0000:03:00.0: 0x00000003 | tsf hi
kernel: iwlagn 0000:03:00.0: 0x00000000 | time gp1
kernel: iwlagn 0000:03:00.0: 0x29703BF0 | time gp2
kernel: iwlagn 0000:03:00.0: 0x00000000 | time gp3
kernel: iwlagn 0000:03:00.0: 0x000111A8 | uCode version
kernel: iwlagn 0000:03:00.0: 0x000000B0 | hw version
kernel: iwlagn 0000:03:00.0: 0x00480303 | board version
kernel: iwlagn 0000:03:00.0: 0x09E8004E | hcmd
kernel: iwlagn 0000:03:00.0: CSR values:
kernel: iwlagn 0000:03:00.0: (2nd byte of CSR_INT_COALESCING is CSR_INT_PERIODIC_REG)
kernel: iwlagn 0000:03:00.0: CSR_HW_IF_CONFIG_REG: 0X00480303
kernel: iwlagn 0000:03:00.0: CSR_INT_COALESCING: 0X0000ff40
kernel: iwlagn 0000:03:00.0: CSR_INT: 0X00000000
kernel: iwlagn 0000:03:00.0: CSR_INT_MASK: 0X00000000
kernel: iwlagn 0000:03:00.0: CSR_FH_INT_STATUS: 0X00000000
kernel: iwlagn 0000:03:00.0: CSR_GPIO_IN: 0X00000030
kernel: iwlagn 0000:03:00.0: CSR_RESET: 0X00000000
kernel: iwlagn 0000:03:00.0: CSR_GP_CNTRL: 0X080403c5
kernel: iwlagn 0000:03:00.0: CSR_HW_REV: 0X000000b0
kernel: iwlagn 0000:03:00.0: CSR_EEPROM_REG: 0X07d60ffd
kernel: iwlagn 0000:03:00.0: CSR_EEPROM_GP: 0X90000001
kernel: iwlagn 0000:03:00.0: CSR_OTP_GP_REG: 0X00030001
kernel: iwlagn 0000:03:00.0: CSR_GIO_REG: 0X00080044
kernel: iwlagn 0000:03:00.0: CSR_GP_UCODE_REG: 0X000093bb
kernel: iwlagn 0000:03:00.0: CSR_GP_DRIVER_REG: 0X00000000
kernel: iwlagn 0000:03:00.0: CSR_UCODE_DRV_GP1: 0X00000000
kernel: iwlagn 0000:03:00.0: CSR_UCODE_DRV_GP2: 0X00000000
kernel: iwlagn 0000:03:00.0: CSR_LED_REG: 0X00000078
kernel: iwlagn 0000:03:00.0: CSR_DRAM_INT_TBL_REG: 0X88214dd2
kernel: iwlagn 0000:03:00.0: CSR_GIO_CHICKEN_BITS: 0X27800200
kernel: iwlagn 0000:03:00.0: CSR_ANA_PLL_CFG: 0X00000000
kernel: iwlagn 0000:03:00.0: CSR_HW_REV_WA_REG: 0X0001001a
kernel: iwlagn 0000:03:00.0: CSR_DBG_HPET_MEM_REG: 0Xffff0010
kernel: iwlagn 0000:03:00.0: FH register values:
kernel: iwlagn 0000:03:00.0: FH_RSCSR_CHNL0_STTS_WPTR_REG: 0X21316d00
kernel: iwlagn 0000:03:00.0: FH_RSCSR_CHNL0_RBDCB_BASE_REG: 0X021479c0
kernel: iwlagn 0000:03:00.0: FH_RSCSR_CHNL0_WPTR: 0X00000060
kernel: iwlagn 0000:03:00.0: FH_MEM_RCSR_CHNL0_CONFIG_REG: 0X80819104
kernel: iwlagn 0000:03:00.0: FH_MEM_RSSR_SHARED_CTRL_REG: 0X000000fc
kernel: iwlagn 0000:03:00.0: FH_MEM_RSSR_RX_STATUS_REG: 0X07030000
kernel: iwlagn 0000:03:00.0: FH_MEM_RSSR_RX_ENABLE_ERR_IRQ2DRV: 0X00000000
kernel: iwlagn 0000:03:00.0: FH_TSSR_TX_STATUS_REG: 0X07ff0001
kernel: iwlagn 0000:03:00.0: FH_TSSR_TX_ERROR_REG: 0X00000000
kernel: iwlagn 0000:03:00.0: Start IWL Event Log Dump: display last 20 entries
kernel: ------------[ cut here ]------------
WARNING: at net/mac80211/util.c:1208 ieee80211_reconfig+0x1f1/0x407()
kernel: Hardware name: 4290W4H
kernel: Pid: 1896, comm: kworker/0:0 Not tainted 3.1.0 #2
kernel: Call Trace:
kernel: [<
ffffffff81036558>] ? warn_slowpath_common+0x73/0x87
kernel: [<
ffffffff813b8966>] ? ieee80211_reconfig+0x1f1/0x407
kernel: [<
ffffffff8139e8dc>] ? ieee80211_recalc_smps_work+0x32/0x32
kernel: [<
ffffffff8139e95a>] ? ieee80211_restart_work+0x7e/0x87
kernel: [<
ffffffff810472fa>] ? process_one_work+0x1c8/0x2e3
kernel: [<
ffffffff810480c9>] ? worker_thread+0x17a/0x23a
kernel: [<
ffffffff81047f4f>] ? manage_workers.clone.18+0x15b/0x15b
kernel: [<
ffffffff81047f4f>] ? manage_workers.clone.18+0x15b/0x15b
kernel: [<
ffffffff8104ba97>] ? kthread+0x7a/0x82
kernel: [<
ffffffff813d21b4>] ? kernel_thread_helper+0x4/0x10
kernel: [<
ffffffff8104ba1d>] ? kthread_flush_work_fn+0x11/0x11
kernel: [<
ffffffff813d21b0>] ? gs_change+0xb/0xb
Cc: <stable@kernel.org> 3.1+
Reported-by: Udo Steinberg <udo@hypervisor.org>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 2 Dec 2011 16:19:17 +0000 (08:19 -0800)]
iwlagn: fix HW crypto for TX-only keys
Group keys in IBSS or AP mode are not programmed
into the device since we give the key to it with
every TX packet. However, we do need mac80211 to
create the MMIC & PN in all cases. Move the code
around to set the key flags all the time. We set
them even when the key is removed again but that
is obviously harmless.
Cc: stable@vger.kernel.org
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Andrei Emeltchenko [Thu, 1 Dec 2011 12:42:08 +0000 (14:42 +0200)]
Bluetooth: remove old code
Remove old code not touched for several years.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Andre Guedes [Fri, 2 Dec 2011 12:13:31 +0000 (21:13 +0900)]
Bluetooth: LE Set Scan Parameter Command
This patch adds the parameter struct and the command complete event
handler to the LE Set Scan Parameter HCI command.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Andre Guedes [Fri, 25 Nov 2011 23:53:38 +0000 (20:53 -0300)]
Bluetooth: Add dev_flags to struct hci_dev
This patch adds the dev_flags field to struct hci_dev. This new
flags variable should be used to define flags related to BR/EDR
and/or LE controller itself. It should be used to define flags
which represents states from the controller. The dev_flags is
cleared in case the controller sends a Reset Command Complete
Event to the host.
Also, this patch adds the HCI_LE_SCAN flag which was created to
track if the controller is performing LE scan or not. The flag
is set/cleared when the controller starts/stops scanning.
This is an initial effort to stop using hdev->flags to define
internal flags since it is exported to userspace by an ioctl.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Andrei Emeltchenko [Thu, 24 Nov 2011 12:52:02 +0000 (14:52 +0200)]
Bluetooth: Add HCI Read Flow Control Mode function
Upstream Code Aurora function with minor trivial fixes.
Origin: git://codeaurora.org/kernel/msm.git
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
John W. Linville [Thu, 1 Dec 2011 15:44:17 +0000 (10:44 -0500)]
Revert "mac80211: clear sta.drv_priv on reconfiguration"
This reverts commit
f785d83a19bca326f79d127a413e35769afc0105.
This was provoking WARNINGs from the iwlegacy drivers.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Brian Gix [Wed, 23 Nov 2011 16:28:36 +0000 (08:28 -0800)]
Bluetooth: Centralize SMP pairing failure handling
Signed-off-by: Brian Gix <bgix@codeaurora.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Brian Gix [Wed, 23 Nov 2011 16:28:35 +0000 (08:28 -0800)]
Bluetooth: Cleanup blkcipher on SMP termination
The blkcipher must be freed to avoid memory leak.
Signed-off-by: Brian Gix <bgix@codeaurora.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Brian Gix [Wed, 23 Nov 2011 16:28:34 +0000 (08:28 -0800)]
Bluetooth: Add HCI User Passkey Req Evt handling
Some MITM scenarios require handling of the User Passkey Request event,
by querying the user, and passing the response back.
Signed-off-by: Brian Gix <bgix@codeaurora.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Brian Gix [Wed, 23 Nov 2011 16:28:33 +0000 (08:28 -0800)]
Bluetooth: Add User Passkey Response handling
For some MITM protection pairing scenarios, the user is
required to enter or accept a 6 digit passkey.
Signed-off-by: Brian Gix <bgix@codeaurora.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Mohammed Shafi Shajakhan [Wed, 30 Nov 2011 15:40:52 +0000 (21:10 +0530)]
ath9k_hw: add default chainmask for AR9462
the default tx/rx chainmask for AR9462 is 0x3.
this patch helps to assign 0x3 rather than 0x7 for
AR9462 with the help of fix_chainmask module if something
goes wrong in reading tx/rx chain mask from OTP/EEPROM
card(though its very unlikely)
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mohammed Shafi Shajakhan [Wed, 30 Nov 2011 15:31:31 +0000 (21:01 +0530)]
ath9k_hw: Fix TX IQ calibration for AR9003
only for AR9485 (or) later chipsets TxIQ calibration
runs as part of AGC calibration. without this patch
TX IQ cal completion i.e. ar9003_hw_tx_iq_cal_run won't be executed
for AR9003
Reviewed-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Axel Lin [Wed, 30 Nov 2011 10:18:06 +0000 (18:18 +0800)]
NFC: pn533: Staticise pn533_data_exchange()
It is not used outside this driver so no need to make the symbol global.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Carpenter [Wed, 30 Nov 2011 08:49:38 +0000 (11:49 +0300)]
brcm80211: fmac: small memory leak on error
We should free "bus_if" here, it's a small leak but it makes the static
checkers happy.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mohammed Shafi Shajakhan [Wed, 30 Nov 2011 08:48:38 +0000 (14:18 +0530)]
ath9k: minor cleanup
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mohammed Shafi Shajakhan [Wed, 30 Nov 2011 05:11:29 +0000 (10:41 +0530)]
ath9k: fix a typo
Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mohammed Shafi Shajakhan [Wed, 30 Nov 2011 05:11:28 +0000 (10:41 +0530)]
ath9k: MCI state machine based on MCI interrupt
Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mohammed Shafi Shajakhan [Wed, 30 Nov 2011 05:11:27 +0000 (10:41 +0530)]
ath9k_hw: Add MCI related changes in chip reset
here we check for BT state and if BT calibration has started,
give 25ms for BT Calibration to finish. we also take care of 2G/5G
switch and LNA transfer incase WLAN is operating in 5G. in case the BT
state is awake when we do WLAN calibration re-calibrate and we reset
the message exchange between WLAN and BT. BT is given preference when
simultaneous CAL request happens. calibration for WLAN/BT is done
assuming that the other co-existing module is in awake state, if not
we continue to do calibration while if the other module's state changes
we need to do restart the calibration handshake
Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mohammed Shafi Shajakhan [Wed, 30 Nov 2011 05:11:26 +0000 (10:41 +0530)]
ath9k_hw: Add support for MCI WLAN calibration
WLAN communicates with BT for its calibration by sending WLAN_CAL_REQ,
waits for BT_CAL_GRANT. This is done with the help of GPM messages.
also WLAN_CAL_DONE messages is sent once WLAN calibration is done.
Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mohammed Shafi Shajakhan [Wed, 30 Nov 2011 05:11:25 +0000 (10:41 +0530)]
ath9k_hw: MCI related changes in set_reset_reg
Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mohammed Shafi Shajakhan [Wed, 30 Nov 2011 05:11:24 +0000 (10:41 +0530)]
ath9k_hw: MCI related changes in chip management
send halt BT GPM if the chip is in network sleep and BT state
is awake
Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mohammed Shafi Shajakhan [Wed, 30 Nov 2011 05:11:23 +0000 (10:41 +0530)]
ath9k: Add functions to allocate/free buffers for MCI
required buffers and dma allocation is done for GPM and SCHED
messages
Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mohammed Shafi Shajakhan [Wed, 30 Nov 2011 05:11:22 +0000 (10:41 +0530)]
ath9k: add MCI specific definitions and structures
Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mohammed Shafi Shajakhan [Wed, 30 Nov 2011 05:11:21 +0000 (10:41 +0530)]
ath9k_hw: check for MCI interrupt in get_isr
check for the condition of MCI interrupt being triggered and
appropriately obtain the values of MCI_INTERRUPT_RX_MSG_RAW and
MCI_INTERRUPT_RAW
Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mohammed Shafi Shajakhan [Wed, 30 Nov 2011 05:11:20 +0000 (10:41 +0530)]
ath9k_hw: check for asynchronous MCI interrupt pending
MCI interrupt is an asynchronous one, so take care of it by having a
check in ath9k_hw_intrpend, which actually decides whether the interrupt
is really for the driver from ath_isr
Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mohammed Shafi Shajakhan [Wed, 30 Nov 2011 05:11:19 +0000 (10:41 +0530)]
ath9k_hw: take care of enabling MCI interrupts
enable MCI interrupt when ath9k_hw_enable_interrupts is called,
like during the completion of chip_reset before which the interrupts
are disabled
Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mohammed Shafi Shajakhan [Wed, 30 Nov 2011 05:11:18 +0000 (10:41 +0530)]
ath9k: Add MCI interrupt to interrupt mask
Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mohammed Shafi Shajakhan [Wed, 30 Nov 2011 05:11:17 +0000 (10:41 +0530)]
ath9k_hw: Add MCI h/w code and state machine
Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mohammed Shafi Shajakhan [Wed, 30 Nov 2011 05:11:16 +0000 (10:41 +0530)]
ath9k_hw: initialize MCI parameters
these parameter will be utilized and modified in the MCI hardware codes
state machine
Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mohammed Shafi Shajakhan [Wed, 30 Nov 2011 05:11:15 +0000 (10:41 +0530)]
ath9k_hw: Add MCI h/w specific structure
Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mohammed Shafi Shajakhan [Wed, 30 Nov 2011 05:11:14 +0000 (10:41 +0530)]
ath9k_hw: add GPIO output MUX related macros
Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mohammed Shafi Shajakhan [Wed, 30 Nov 2011 05:11:13 +0000 (10:41 +0530)]
ath9k_hw: add definitions to support MCI h/w code
these definitions will be used by MCI state machine and the corresponding
hardware code
Cc: Wilson Tsao <wtsao@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Tue, 29 Nov 2011 19:37:35 +0000 (11:37 -0800)]
nfc: Remove function tracer like entry messages
Logging messages that mimic function tracer enter/exit
aren't necessary. Just remove them.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Tue, 29 Nov 2011 19:37:34 +0000 (11:37 -0800)]
nfc: Remove unused nfc_printk and nfc_<level> macros
All uses have been removed, so killing what's not necessary.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Tue, 29 Nov 2011 19:37:33 +0000 (11:37 -0800)]
nfc: Convert nfc_dbg to pr_debug
Using the standard debugging mechanisms is better than
subsystem specific ones when the subsystem doesn't use
a specific struct.
Coalesce long formats.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Joe Perches [Tue, 29 Nov 2011 19:37:32 +0000 (11:37 -0800)]
nfc: Use standard logging styles
Using the normal logging styles is preferred over
subsystem specific styles when the subsystem does
not take a specific struct.
Convert nfc_<level> specific messages to pr_<level>
Add newlines to uses.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Tue, 29 Nov 2011 17:40:16 +0000 (12:40 -0500)]
prism54: remove private driver ioctls
As of hostap_0_7_1~358 the CONFIG_DRIVER_PRISM54
was removed from upstream wpa_supplicant/hostapd so
lets just kill the useless old prism54 private ioctl
crap.
Cc: Jouni Malinen <j@w1.fi>
Cc: David Miller <davem@davemloft.net>
Reported-by: David Miller <davem@davemloft.net>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mohammed Shafi Shajakhan [Tue, 29 Nov 2011 15:00:35 +0000 (20:30 +0530)]
ath9k: change the default antenna settings based on diversity
change the AR_DEF_ANTENNA register settings i.e setting default antenna
setting only for antenna diversity enabled chipsets. no point in
doing this for MIMO chipsets
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mohammed Shafi Shajakhan [Tue, 29 Nov 2011 14:36:15 +0000 (20:06 +0530)]
ath9k: Fix LED GPIO pin for AR9462
GPIO pin 4 is assigned AR9462 chipsets LED.
while GPIO pin 0 worked for obselete AR9462 chipsets though
they are meant for EEPROM as per Russell
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: Russell Hu <rhu@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mohammed Shafi Shajakhan [Tue, 29 Nov 2011 13:51:53 +0000 (19:21 +0530)]
mac80211: remove unused function declaration
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 29 Nov 2011 09:20:02 +0000 (10:20 +0100)]
mac80211: revert on-channel work optimisations
The on-channel work optimisations have caused a
number of issues, and the code is unfortunately
very complex and almost impossible to follow.
Instead of attempting to put in more workarounds
let's just remove those optimisations, we can
work on them again later, after we change the
whole auth/assoc design.
This should fix rate_control_send_low() warnings,
see RH bug 731365.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Mon, 28 Nov 2011 21:38:50 +0000 (16:38 -0500)]
mwifiex: fix usage of set tx power
mBm is passed but dBm was assumed...
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Mon, 28 Nov 2011 21:38:49 +0000 (16:38 -0500)]
brcm80211: avoid code duplication on set tx power
Both cases are doing the same so treat the switch cases
for both as an "or".
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Mon, 28 Nov 2011 21:38:48 +0000 (16:38 -0500)]
brcm80211: fix usage of set tx power
mBm is passed but dBm was assumed...
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Mon, 28 Nov 2011 21:38:46 +0000 (16:38 -0500)]
cfg80211: clarify set tx power mBm documentation
Tons of drivers missed that we use mBm and not dBm...
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Axel Lin [Mon, 28 Nov 2011 09:15:04 +0000 (17:15 +0800)]
net: rfkill: convert net/rfkill/* to use module_platform_driver()
This patch converts the drivers in net/rfkill/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Antonio Ospite <ospite@studenti.unina.it>
Cc: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Simon Wunderlich [Wed, 30 Nov 2011 15:56:30 +0000 (16:56 +0100)]
mac80211: fill rate filter for internal scan requests
The rates bitmap for internal scan requests shoud be filled,
otherwise there will be probe requests with zero rates supported.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Mon, 28 Nov 2011 21:47:16 +0000 (16:47 -0500)]
cfg80211: amend regulatory NULL dereference fix
Johannes' patch for "cfg80211: fix regulatory NULL dereference"
broke user regulaotry hints and it did not address the fact that
last_request was left populated even if the previous regulatory
hint was stale due to the wiphy disappearing.
Fix user reguluatory hints by only bailing out if for those
regulatory hints where a request_wiphy is expected. The stale last_request
considerations are addressed through the previous fixes on last_request
where we reset the last_request to a static world regdom request upon
reset_regdomains(). In this case though we further enhance the effect
by simply restoring reguluatory settings completely.
Cc: stable@vger.kernel.org
Cc: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Mon, 28 Nov 2011 21:47:15 +0000 (16:47 -0500)]
cfg80211: fix race on init and driver registration
There is a theoretical race that if hit will trigger
a crash. The race is between when we issue the first
regulatory hint, regulatory_hint_core(), gets processed
by the workqueue and between when the first device
gets registered to the wireless core. This is not easy
to reproduce but it was easy to do so through the
regulatory simulator I have been working on. This
is a port of the fix I implemented there [1].
[1] https://github.com/mcgrof/regsim/commit/
a246ccf81f059cb662eee288aa13100f631e4cc8
Cc: stable@vger.kernel.org
Cc: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Emmanuel Grumbach [Fri, 25 Nov 2011 19:11:48 +0000 (11:11 -0800)]
iwlwifi: help to debug AGG SM inconsistencies
Add more data when inconsistencies occur in the AGG state machine.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 25 Nov 2011 19:11:47 +0000 (11:11 -0800)]
iwlwifi: show the configuration option
Not sure it is the best way to do it, but many times we want to know what the
configuration options were enabled for the compiled driver.
Let's just log the options during load time; so there were be no confusion.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Fri, 25 Nov 2011 19:11:46 +0000 (11:11 -0800)]
iwlwifi: show command string for REPLY_D3_CONFIG
missing the string, add it
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 25 Nov 2011 19:11:45 +0000 (11:11 -0800)]
iwlagn: allow up to uCode API 6 for 6000 devices
Since the uCode hasn't been released (yet?),
warn only if using older than API 4, but load
anything up to API 6.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 25 Nov 2011 19:11:44 +0000 (11:11 -0800)]
iwlagn: dynamically allocate & reflect calibration data
This makes handling the calibration data more generic
and no longer requires updating IWL_CALIB_MAX when a
new uCode comes with more calibration packets. Since
we just copy the data back, there's also no need for
understanding which calibration we received -- we can
just reflect it back to the runtime uCode.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 25 Nov 2011 19:11:43 +0000 (11:11 -0800)]
iwlagn: remove calibration knowledge
The init microcode knows very well which calibrations
are required and sends us results for those that are.
Consequently, we can just send all of those to the RT
uCode again.
The problem with having the driver know about this is
that it is a uCode feature, not a hardware feature so
the config is completely unsuitable.
The only thing we need to check is whether the device
needs crystal calibration or not, add a new parameter
to the configuration for that.
This makes new uCode work on 6000 series devices.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hsu, Kenny [Fri, 25 Nov 2011 19:11:42 +0000 (11:11 -0800)]
iwlwifi: add tm commands for indirect register access
Create new testmode commands to suppot indirect access
of peripheral register.
- IWL_TM_CMD_APP2DEV_INDIRECT_REG_READ32
- IWL_TM_CMD_APP2DEV_INDIRECT_REG_WRITE32
Meanwhile, add affix "DIRECT" into original register access
commands for better discrimination with new commands.
- IWL_TM_CMD_APP2DEV_DIRECT_REG_READ32
- IWL_TM_CMD_APP2DEV_DIRECT_REG_WRITE32
- IWL_TM_CMD_APP2DEV_DIRECT_REG_WRITE8
Signed-off-by: Kenny Hsu <kenny.hsu@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nick Kossifidis [Fri, 25 Nov 2011 18:40:31 +0000 (20:40 +0200)]
ath5k: Optimize ath5k_cw_validate
Optimize ath5k_cw_validate by using the classic (X & (X - 1)) == 0
check to see if a number is power of 2.
v2: Use functions from log2.h instead
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nick Kossifidis [Fri, 25 Nov 2011 18:40:30 +0000 (20:40 +0200)]
ath5k: Renumber hw queue ids
According to documentation higher DCUs have higher priority and should
be used for beacons and CAB traffic. More specifically DCU 9 should be
used for beacons and DCU 8 for CAB traffic, I assumed DCU 7 should be
OK for UAPSD traffic.
Note that DCU 8 and 9 are special because they can only be mapped to a single
QCU each but since we use a 1:1 mapping between QCUs and DCUs anyway we don't
have to change much.
P.S. I also did a few related cleanups on qcu.c and ath5k.h
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nick Kossifidis [Fri, 25 Nov 2011 18:40:29 +0000 (20:40 +0200)]
ath5k: ath5k_ani_period_restart only touches struct ath5k_ani_state
No need to take ath5k_hw as an argument.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nick Kossifidis [Fri, 25 Nov 2011 18:40:28 +0000 (20:40 +0200)]
ath5k: MRR support and 2GHz radio override belong in ah_capabilities
MRR support and 2GHz radio override belong in ah_capabilities and we
should use them (e.g. so far we used to set mrr descriptor without
checking if MRR support is enabled + we checked for MRR support 2
times, one by trying to set up an MRR descriptor and another one based
on MAC version).
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nick Kossifidis [Fri, 25 Nov 2011 18:40:27 +0000 (20:40 +0200)]
ath5k: Add a module parameter to disable hw rf kill switch
Add a module parameter to disable hw rf kill switch (GPIO interrupt) because
in some cases when the card doesn't come with the laptop, EEPROM configuration
doesn't match laptop's configuration and rf kill interrupt always fires up and
disables hw. I thought of moving this to debugfs and make it per-card but
this way it's easier for users and distros to handle.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Tested-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nick Kossifidis [Fri, 25 Nov 2011 18:40:26 +0000 (20:40 +0200)]
ath5k: We always do full calibration on AR5210
There is no short calibration on AR5210, make sure we treat it always
as full calibration.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nick Kossifidis [Fri, 25 Nov 2011 18:40:25 +0000 (20:40 +0200)]
ath5k: Cleanups v2 + add kerneldoc on all hw functions
No functional changes
Add kernel doc for all ath5k_hw_* functions and strcucts. Also do some cleanup,
rename ath5k_hw_init_beacon to ath5k_hw_init_beacon_timers, remove an unused
variable from ath5k_hw_pcu_init and a few obsolete macros, mostly related to XR.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nick Kossifidis [Fri, 25 Nov 2011 18:40:24 +0000 (20:40 +0200)]
ath5k: Use usleep_range where possible
Use usleep_range where possible to reduce busy waits
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nick Kossifidis [Fri, 25 Nov 2011 18:40:23 +0000 (20:40 +0200)]
ath5k: Calibration re-work
Noise floor calibration does not interfere with traffic and should run more
often as part of our "short calibration". The full calibration is not the
noise floor calibration but the AGC + Gain_F (on RF5111 and RF5112) calibration
and should run less often because it does interfere with traffic.
So
Short calibration -> I/Q & NF Calibration
Long calibration -> Short + AGC + Gain_F
This patch was for some time on my pub/ dir on www.kernel.org and has been tested
by a few people and me. I think it's O.K. to go in.
I also changed ah_calibration to ah_iq_cal_needed to make more sense.
v2 Use a workqueue instead of a tasklet for calibration
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nick Kossifidis [Fri, 25 Nov 2011 18:40:22 +0000 (20:40 +0200)]
ath5k: Cleanups v1
No functional changes, just a few comments/documentation/cleanup
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nick Kossifidis [Fri, 25 Nov 2011 18:40:21 +0000 (20:40 +0200)]
ath5k: Add TXNOFRM to INT_TX_ALL
Add TXNOFRM to INT_TX_ALL since it's a TX interrupt too.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nick Kossifidis [Fri, 25 Nov 2011 18:40:20 +0000 (20:40 +0200)]
ath5k: Switch from read-and-clear to write-to-clear method when handling PISR/SISR registers
Since card has 12 tx queues and we want to keep track of the interrupts
per queue we can't fit all these interrupt bits on a single register.
So we have 5 registers, the primary interrupt status register (PISR) and
the 4 secondary interupt status registers (SISRs).
In order to be able to read them all at once (atomic operation) Atheros
introduced the Read-And-Clear registers to make things easier. So when
reading RAC_PISR register, hw does a read on PISR and all SISRs, returns
the value of PISR, copies all SISR values to their shadow copies (RAC_SISRx)
and clears PISR and SISRs. This saves us from reading PISR/SISRs in a sequence.
So far we 've used this approach and MadWiFi/Windows driver etc also used it
for years.
It turns out this operation is not atomic after all (at least not on all cards)
That means it's possible to loose some interrupts because they came after the
copy step and hw cleared them on the clean step !
That's probably the reason we got missed beacons, got stuck queues etc and
couldn't figure out what was going on.
With this patch we switch from RaC operation to an alternative method (that
makes more sense IMHO anyway, I just chose to be on the safe side so far).
Instead of reading RAC registers, we read the normal PISR/SISR registers and
clear any bits we got by writing them back on the register. This will clear only
the bits we got on our read step and leave any new bits unaffected (at least
that's what docs say). So if any new interrupts come up we won't miss it.
I've tested this with an AR5213 and an AR2425 and it seems O.K.
Many thanks to Adrian Chadd for debuging this and reviewing the patch !
v2: Make sure we don't clear PISR bits that map to SISR generated interrupts
(added a comment on the code for this)
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 25 Nov 2011 12:31:53 +0000 (13:31 +0100)]
mac80211: remove tracing config symbol
There's little point in this config symbol, if
tracing is disabled the overhead is negligible
and if you think it's too bad you can always
turn off tracing completely.
Also remove the part where we don't have sparse
check the tracing code -- it seems that it can
now deal with it (or the code changed).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Thomas Pedersen [Fri, 25 Nov 2011 01:15:26 +0000 (17:15 -0800)]
mac80211: clean up rx_h_mesh_fwding
Lose about two levels of unnecessary indentation.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Thomas Pedersen [Fri, 25 Nov 2011 01:15:25 +0000 (17:15 -0800)]
mac80211: don't initiate path discovery when forwarding frame with unknown DA
We used to initiate a path discovery when receiving a frame for which
there is no forwarding information. To cut down on PREQ spam, just send
a (gated) PERR in response.
Also separate path discovery logic from nexthop querying. This patch
means we no longer queue frames when forwarding, so kill the PERR TX
stuff in discard_frame().
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Thomas Pedersen [Fri, 25 Nov 2011 01:15:24 +0000 (17:15 -0800)]
{nl,cfg,mac}80211: implement dot11MeshHWMPperrMinInterval
As per 802.11mb 13.9.11.3
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Thomas Pedersen [Fri, 25 Nov 2011 01:15:23 +0000 (17:15 -0800)]
mac80211: fix forwarded mesh frame queue mapping
We can't rely on ieee80211_select_queue() to do its job at this point
since the skb->protocol is not yet known. Instead, factor out and reuse
the queue mapping logic for injected frames.
Also, to mitigate congestion, forwarded frames should be dropped if the
outgoing queue was stopped. This was not correctly implemented as we
were not checking the right queue. Furthermore, we were dropping frames
that had arrived to their destination if that queue was stopped.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Thomas Pedersen [Fri, 25 Nov 2011 01:15:22 +0000 (17:15 -0800)]
mac80211: fix switched HWMP frame addresses
HWMP originator and target addresses were switched on the air but also
on reception, which is why path selection still worked.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Thomas Pedersen [Fri, 25 Nov 2011 01:15:21 +0000 (17:15 -0800)]
mac80211: failed forwarded mesh frame addressing
Don't write the TA until next hop is actually known, since we might need
the original TA for sending a PERR. Previously we would send a PERR to
ourself if path resolution for a forwarded frame failed.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Chun-Yeow Yeoh [Fri, 25 Nov 2011 01:15:20 +0000 (17:15 -0800)]
{nl,cfg,mac}80211: Allow Setting Multicast Rate in Mesh
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Veli-Pekka Peltola [Thu, 24 Nov 2011 19:35:28 +0000 (21:35 +0200)]
hostap_cs: add ID for Canon K30225
Signed-off-by: Veli-Pekka Peltola <veli-pekka.peltola@bluegiga.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ben Greear [Thu, 24 Nov 2011 19:15:21 +0000 (11:15 -0800)]
mac80211: Make __check_htcap_disable static.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Lars-Peter Clausen [Thu, 24 Nov 2011 15:29:20 +0000 (16:29 +0100)]
wireless: Remove redundant spi driver bus initialization
In ancient times it was necessary to manually initialize the bus field of an
spi_driver to spi_bus_type. These days this is done in spi_driver_register(),
so we can drop the manual assignment.
The patch was generated using the following coccinelle semantic patch:
// <smpl>
@@
identifier _driver;
@@
struct spi_driver _driver = {
.driver = {
- .bus = &spi_bus_type,
},
};
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Dan Williams <dcbw@redhat.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Cc: Luciano Coelho <coelho@ti.com>
Cc: libertas-dev@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Eliad Peller [Thu, 24 Nov 2011 14:50:00 +0000 (16:50 +0200)]
mac80211: call skb_put() before copying the data (trivial)
It doesn't have any actual effect here, but we should
skb_put() *before* copying the data.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Thu, 24 Nov 2011 13:47:36 +0000 (14:47 +0100)]
mac80211: fix TX warning
Emmanuel reported that my previous patches to enable
handing all fragments to drivers at once triggered
the warning that the SKB queue wasn't empty. This is
happening when we actually queue up some frames and
don't hand them to the driver (queues are stopped).
The reason for it is that my code that splices the
frame(s) over to the pending queue didn't re-init
the local queue, so skb_queue_empty() was false. Fix
this by using the _init versions of the splicing.
Also, convert the warning to WARN_ON_ONCE.
Reported-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Tested-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Thu, 24 Nov 2011 08:13:26 +0000 (09:13 +0100)]
rt2x00: Pass BlockAck and BlackAckReq frames to mac80211 in monitor mode
Previously BlockAcks were always dropped by the rt2800 hardware while
BlockAckReqs were always accepted. However, both are only useful on
monitor interfaces at the moment and both are control frames. So
pass them up when mac80211 sets FIF_CONTROL.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>