OSDN Git Service
Michael Poole [Fri, 5 Feb 2010 17:23:43 +0000 (12:23 -0500)]
Bluetooth: Keep a copy of each HID device's report descriptor
The report descriptor is read by user space (via the Service
Discovery Protocol), so it is only available during the ioctl
to connect. However, the HID probe function that needs the
descriptor might not be called until a specific module is
loaded. Keep a copy of the descriptor so it is available for
later use.
Signed-off-by: Michael Poole <mdpoole@troilus.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Nick Pelly [Fri, 13 Nov 2009 22:16:32 +0000 (14:16 -0800)]
Bluetooth: Enter active mode before establishing a SCO link.
When in sniff mode with a long interval time (1.28s) it can take 4+ seconds
to establish a SCO link. Fix by requesting active mode before requesting
SCO connection. This improves SCO setup time to ~500ms.
Bluetooth headsets that use a long interval time, and exhibit the long
SCO connection time include Motorola H790, HX1 and H17. They have a
CSR 2.1 chipset.
Verified this behavior and fix with host Bluetooth chipsets: BCM4329 and
TI1271.
2009-10-13 14:17:46.183722 > HCI Event: Mode Change (0x14) plen 6
status 0x00 handle 1 mode 0x02 interval 2048
Mode: Sniff
2009-10-13 14:17:53.436285 < HCI Command: Setup Synchronous Connection (0x01|0x0028) plen 17
handle 1 voice setting 0x0060
2009-10-13 14:17:53.445593 > HCI Event: Command Status (0x0f) plen 4
Setup Synchronous Connection (0x01|0x0028) status 0x00 ncmd 1
2009-10-13 14:17:57.788855 > HCI Event: Synchronous Connect Complete 0x2c) plen 17
status 0x00 handle 257 bdaddr 00:1A:0E:F1:A4:7F type eSCO
Air mode: CVSD
Signed-off-by: Nick Pelly <npelly@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Yoichi Yuasa [Thu, 4 Feb 2010 00:55:51 +0000 (09:55 +0900)]
Bluetooth: Fix memory leak in Marvell BT-over-SDIO driver
Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Nick Pelly [Thu, 4 Feb 2010 00:18:36 +0000 (16:18 -0800)]
Bluetooth: Do not call rfcomm_session_put() for RFCOMM UA on closed socket
When processing a RFCOMM UA frame when the socket is closed and we were
not the RFCOMM initiator would cause rfcomm_session_put() to be called
twice during rfcomm_process_rx(). This would cause a kernel panic in
rfcomm_session_close() then.
This could be easily reproduced during disconnect with devices such as
Motorola H270 that send RFCOMM UA followed quickly by L2CAP disconnect
request. This trace for this looks like:
2009-09-21 17:22:37.788895 < ACL data: handle 1 flags 0x02 dlen 8
L2CAP(d): cid 0x0041 len 4 [psm 3]
RFCOMM(s): DISC: cr 0 dlci 20 pf 1 ilen 0 fcs 0x7d
2009-09-21 17:22:37.906204 > HCI Event: Number of Completed Packets (0x13) plen 5
handle 1 packets 1
2009-09-21 17:22:37.933090 > ACL data: handle 1 flags 0x02 dlen 8
L2CAP(d): cid 0x0040 len 4 [psm 3]
RFCOMM(s): UA: cr 0 dlci 20 pf 1 ilen 0 fcs 0x57
2009-09-21 17:22:38.636764 < ACL data: handle 1 flags 0x02 dlen 8
L2CAP(d): cid 0x0041 len 4 [psm 3]
RFCOMM(s): DISC: cr 0 dlci 0 pf 1 ilen 0 fcs 0x9c
2009-09-21 17:22:38.744125 > HCI Event: Number of Completed Packets (0x13) plen 5
handle 1 packets 1
2009-09-21 17:22:38.763687 > ACL data: handle 1 flags 0x02 dlen 8
L2CAP(d): cid 0x0040 len 4 [psm 3]
RFCOMM(s): UA: cr 0 dlci 0 pf 1 ilen 0 fcs 0xb6
2009-09-21 17:22:38.783554 > ACL data: handle 1 flags 0x02 dlen 12
L2CAP(s): Disconn req: dcid 0x0040 scid 0x0041
Avoid calling rfcomm_session_put() twice by skipping this call
in rfcomm_recv_ua() if the socket is closed.
Signed-off-by: Nick Pelly <npelly@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Marcel Holtmann [Wed, 3 Feb 2010 23:52:18 +0000 (15:52 -0800)]
Bluetooth: Fix sleeping function in RFCOMM within invalid context
With the commit
9e726b17422bade75fba94e625cd35fd1353e682 the
rfcomm_session_put() gets accidentially called from a timeout
callback and results in this:
BUG: sleeping function called from invalid context at net/core/sock.c:1897
in_atomic(): 1, irqs_disabled(): 0, pid: 0, name: swapper
Pid: 0, comm: swapper Tainted: P 2.6.32 #31
Call Trace:
<IRQ> [<
ffffffff81036455>] __might_sleep+0xf8/0xfa
[<
ffffffff8138ef1d>] lock_sock_nested+0x29/0xc4
[<
ffffffffa03921b3>] lock_sock+0xb/0xd [l2cap]
[<
ffffffffa03948e6>] l2cap_sock_shutdown+0x1c/0x76 [l2cap]
[<
ffffffff8106adea>] ? clockevents_program_event+0x75/0x7e
[<
ffffffff8106bea2>] ? tick_dev_program_event+0x37/0xa5
[<
ffffffffa0394967>] l2cap_sock_release+0x27/0x67 [l2cap]
[<
ffffffff8138c971>] sock_release+0x1a/0x67
[<
ffffffffa03d2492>] rfcomm_session_del+0x34/0x53 [rfcomm]
[<
ffffffffa03d24c5>] rfcomm_session_put+0x14/0x16 [rfcomm]
[<
ffffffffa03d28b4>] rfcomm_session_timeout+0xe/0x1a [rfcomm]
[<
ffffffff810554a8>] run_timer_softirq+0x1e2/0x29a
[<
ffffffffa03d28a6>] ? rfcomm_session_timeout+0x0/0x1a [rfcomm]
[<
ffffffff8104e0f6>] __do_softirq+0xfe/0x1c5
[<
ffffffff8100e8ce>] ? timer_interrupt+0x1a/0x21
[<
ffffffff8100cc4c>] call_softirq+0x1c/0x28
[<
ffffffff8100e05b>] do_softirq+0x33/0x6b
[<
ffffffff8104daf6>] irq_exit+0x36/0x85
[<
ffffffff8100d7a9>] do_IRQ+0xa6/0xbd
[<
ffffffff8100c493>] ret_from_intr+0x0/0xa
<EOI> [<
ffffffff812585b3>] ? acpi_idle_enter_bm+0x269/0x294
[<
ffffffff812585a9>] ? acpi_idle_enter_bm+0x25f/0x294
[<
ffffffff81373ddc>] ? cpuidle_idle_call+0x97/0x107
[<
ffffffff8100aca0>] ? cpu_idle+0x53/0xaa
[<
ffffffff81429006>] ? rest_init+0x7a/0x7c
[<
ffffffff8177bc8c>] ? start_kernel+0x389/0x394
[<
ffffffff8177b29c>] ? x86_64_start_reservations+0xac/0xb0
[<
ffffffff8177b384>] ? x86_64_start_kernel+0xe4/0xeb
To fix this, the rfcomm_session_put() needs to be moved out of
rfcomm_session_timeout() into rfcomm_process_sessions(). In that
context it is perfectly fine to sleep and disconnect the socket.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Tested-by: David John <davidjon@xenontk.org>
Nick Pelly [Wed, 3 Feb 2010 19:42:26 +0000 (11:42 -0800)]
Bluetooth: Fallback eSCO to SCO on error 0x1a (Unsupported Remote Feature)
General Motors carkits that use LGE BT chipsets return this error code
when an eSCO is attempted, despite advertising eSCO support.
2009-08-13 14:41:39.755518 < HCI Command: Setup Synchronous Connection (0x01|0x0028) plen 17
handle 1 voice setting 0x0060
2009-08-13 14:41:39.757563 > HCI Event: Command Status (0x0f) plen 4
Setup Synchronous Connection (0x01|0x0028) status 0x00 ncmd 1
2009-08-13 14:41:39.789484 > HCI Event: Synchronous Connect Complete (0x2c) plen 17
status 0x1a handle 257 bdaddr 00:1E:B2:23:5E:B3 type eSCO
Error: Unsupported Remote Feature / Unsupported LMP Feature
Signed-off-by: Jaikumar Ganesh <jaikumar@google.com>
Signed-off-by: Nick Pelly <npelly@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Evgeniy Polyakov [Tue, 2 Feb 2010 23:58:48 +0000 (15:58 -0800)]
connector: Delete buggy notification code.
On Tue, Feb 02, 2010 at 02:57:14PM -0800, Greg KH (gregkh@suse.de) wrote:
> > There are at least two ways to fix it: using a big cannon and a small
> > one. The former way is to disable notification registration, since it is
> > not used by anyone at all. Second way is to check whether calling
> > process is root and its destination group is -1 (kind of priveledged
> > one) before command is dispatched to workqueue.
>
> Well if no one is using it, removing it makes the most sense, right?
>
> No objection from me, care to make up a patch either way for this?
Getting it is not used, let's drop support for notifications about
(un)registered events from connector.
Another option was to check credentials on receiving, but we can always
restore it without bugs if needed, but genetlink has a wider code base
and none complained, that userspace can not get notification when some
other clients were (un)registered.
Kudos for Sebastian Krahmer <krahmer@suse.de>, who found a bug in the
code.
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 2 Feb 2010 17:04:58 +0000 (09:04 -0800)]
Merge branch 'master' of git://git./linux/kernel/git/kaber/nf-2.6
Sathya Perla [Tue, 2 Feb 2010 15:48:40 +0000 (07:48 -0800)]
be2net: use eq-id to calculate cev-isr reg offset
cev-isr reg offset for each function is better calculated using (any) eq-id
alloted to that function instead of using pci-func number(which
does not work in some configurations...)
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 1 Feb 2010 07:34:58 +0000 (23:34 -0800)]
Merge branch 'master' of git://git./linux/kernel/git/holtmann/bluetooth-2.6
Bastien Nocera [Wed, 20 Jan 2010 12:00:42 +0000 (12:00 +0000)]
Bluetooth: Use the control channel for raw HID reports
In commit
2da31939a42f7a676a0bc5155d6a0a39ed8451f2, support
for Bluetooth hid_output_raw_report was added, but it pushes
the data to the interrupt channel instead of the contol one.
This patch makes hid_output_raw_report use the control channel
instead. Using the interrupt channel was a mistake.
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Vikram Kandukuri [Wed, 6 Jan 2010 13:34:15 +0000 (19:04 +0530)]
Bluetooth: Add DFU driver for Atheros Bluetooth chipset AR3011
Signed-off-by: Vikram Kandukuri <vikram.kandukuri@atheros.com>
Signed-off-by: Alicke Xu <sxu@atheros.com>
Reviewed-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Mike Frysinger [Mon, 14 Sep 2009 17:43:49 +0000 (13:43 -0400)]
Bluetooth: Redo checks in IRQ handler for shared IRQ support
Commit
ac019360fe3 changed the irq handler logic to BUG_ON rather than
returning IRQ_NONE when the incoming argument is invalid. While this
works in most cases, it doesn't work when the IRQ is shared with other
devices (or when DEBUG_SHIRQ is enabled).
So revert the previous change and replace the warning message with a
comment explaining that we want this behavior.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Andrei Emeltchenko [Wed, 23 Dec 2009 11:07:14 +0000 (13:07 +0200)]
Bluetooth: Fix memory leak in L2CAP
Move skb_clone after error confition check so it is not going
potentially out of the scope.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@nokia.com>
Acked-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Andrei Emeltchenko [Tue, 22 Dec 2009 13:58:08 +0000 (15:58 +0200)]
Bluetooth: Remove double free of SKB pointer in L2CAP
Trivial fix for double free of SKB pointer with kfree_skb to
make code simplier and cleaner. Remove unused variable err.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@nokia.com>
Acked-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Ben Hutchings [Fri, 29 Jan 2010 05:37:18 +0000 (21:37 -0800)]
cdc_ether: Partially revert "usbnet: Set link down initially ..."
Commit
37e8273cd30592d3a82bcb70cbb1bdc4eaeb6b71 ("usbnet: Set link down
initially for drivers that update link state") changed the initial link
state in cdc_ether and other drivers based on the understanding that the
devices they support generate link change interrupts. However, this is
optional in the CDC Ethernet protocol, and two users have reported in
<http://bugzilla.kernel.org/show_bug.cgi?id=14791> that the link state
for their devices remains down. Therefore, revert the change in
cdc_ether.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Tested-by: Avi Rozen <avi.rozen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 29 Jan 2010 05:36:21 +0000 (21:36 -0800)]
be2net: Fix memset() arg ordering.
Noticed by Ben Hutchings.
Signed-off-by: David S. Miller <davem@davemloft.net>
stephen hemminger [Mon, 25 Jan 2010 23:34:15 +0000 (23:34 +0000)]
bonding: bond_open error return value
The convention for API functions in kernel is to return errno value;
bond_open would return -1 if alb setup failed. The only reason that
could happen is if kmalloc() failed.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John Fastabend [Wed, 27 Jan 2010 16:38:06 +0000 (16:38 +0000)]
ixgbe: if ixgbe_copy_dcb_cfg is going to fail learn about it early
Call ixgbe_copy_dcb_cfg() earlier in the ixgbe_dcbnl_set_all() so that
we can learn if this is going to fail as early as possible. Previously,
ixgbe_down or ixgbe_close were being called before this check and the
IXGBE_RESETTING bit was being set and cleared. Worse if this failed
the corresponding ixgbe_up/ndo_open would not called.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: PJ Waskiewicz <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John Fastabend [Wed, 27 Jan 2010 16:37:44 +0000 (16:37 +0000)]
ixgbe: set the correct DCB bit for pg tx settings
Set the correct bit BIT_PG_TX when tx PG settings are set.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: PJ Waskiewicz <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Wed, 27 Jan 2010 15:30:39 +0000 (15:30 +0000)]
igbvf: fix issue w/ mapped_as_page being left set after unmap
This change fixes an issue in igbvf with mapped_as_page being left set
after a page is unmapped which results in buffers which are mapped via map
single being unmapped as page.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Choi, David [Wed, 27 Jan 2010 06:03:16 +0000 (06:03 +0000)]
drivers/net: ks8851_mll ethernet network driver
Hello David Miller,
I fix a bug in ks8851_mll driver, which has existed since 2.6.32-rc6.
>From : David J. Choi <david.choi@micrel.com>
Fix a bug that the data pointers in the interrupt handler are set wrong, which is related with the 5th parameter of request_irq().
Signed-off-by : David J. Choi <david.choi@micrel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ajit Khaparde [Wed, 27 Jan 2010 21:56:44 +0000 (21:56 +0000)]
be2net: Bug fix to support newer generation of BE ASIC
Bug fix in be2net for newer generation of BladeEngine ASIC.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Thu, 28 Jan 2010 13:42:33 +0000 (05:42 -0800)]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-2.6
Ben Hutchings [Tue, 26 Jan 2010 18:27:09 +0000 (18:27 +0000)]
starfire: clean up properly if firmware loading fails
netdev_open() will return without cleaning up net device or hardware state
if firmware loading fails. This results in a BUG() on a second attempt to
bring the interface up, reported in
<http://bugzilla.kernel.org/show_bug.cgi?id=15091>, and probably has even
worse effects if the driver is removed afterwards.
Call netdev_close() to clean up on failure.
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=15091
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Reported-by: Michael Moffatt <michael@moffatt.org.nz>
Tested-by: Michael Moffatt <michael@moffatt.org.nz>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Zhu Yi [Tue, 26 Jan 2010 07:58:57 +0000 (15:58 +0800)]
mac80211: fix NULL pointer dereference when ftrace is enabled
I got below kernel oops when I try to bring down the network interface if
ftrace is enabled. The root cause is drv_ampdu_action() is passed with a
NULL ssn pointer in the BA session tear down case. We need to check and
avoid dereferencing it in trace entry assignment.
BUG: unable to handle kernel NULL pointer dereference
Modules linked in: at (null)
IP: [<
f98fe02a>] ftrace_raw_event_drv_ampdu_action+0x10a/0x160 [mac80211]
*pde =
00000000
Oops: 0000 [#1] SMP DEBUG_PAGEALLOC
[...]
Call Trace:
[<
f98fdf20>] ? ftrace_raw_event_drv_ampdu_action+0x0/0x160 [mac80211]
[<
f98dac4c>] ? __ieee80211_stop_rx_ba_session+0xfc/0x220 [mac80211]
[<
f98d97fb>] ? ieee80211_sta_tear_down_BA_sessions+0x3b/0x50 [mac80211]
[<
f98dc6f6>] ? ieee80211_set_disassoc+0xe6/0x230 [mac80211]
[<
f98dc6ac>] ? ieee80211_set_disassoc+0x9c/0x230 [mac80211]
[<
f98dcbb8>] ? ieee80211_mgd_deauth+0x158/0x170 [mac80211]
[<
f98e4bdb>] ? ieee80211_deauth+0x1b/0x20 [mac80211]
[<
f8987f49>] ? __cfg80211_mlme_deauth+0xe9/0x120 [cfg80211]
[<
f898b870>] ? __cfg80211_disconnect+0x170/0x1d0 [cfg80211]
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patrick McHardy [Tue, 26 Jan 2010 16:04:02 +0000 (17:04 +0100)]
netfilter: ctnetlink: fix expectation mask dump
The protocol number is not initialized, so userspace can't interpret
the layer 4 data properly.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Shan Wei [Tue, 26 Jan 2010 02:40:38 +0000 (02:40 +0000)]
ipv6: conntrack: Add member of user to nf_ct_frag6_queue structure
The commit
0b5ccb2(title:ipv6: reassembly: use seperate reassembly queues for
conntrack and local delivery) has broken the saddr&&daddr member of
nf_ct_frag6_queue when creating new queue. And then hash value
generated by nf_hashfn() was not equal with that generated by fq_find().
So, a new received fragment can't be inserted to right queue.
The patch fixes the bug with adding member of user to nf_ct_frag6_queue structure.
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu [Mon, 25 Jan 2010 23:51:01 +0000 (15:51 -0800)]
virtio_net: Make delayed refill more reliable
I have seen RX stalls on a machine that experienced a suspected
OOM. After the stall, the RX buffer is empty on the guest side
and there are exactly 16 entries available on the host side. As
the number of entries is less than that required by a maximal
skb, the host cannot proceed.
The guest did not have a refill job scheduled.
My diagnosis is that an OOM had occured, with the delayed refill
job scheduled. The job was able to allocate at least one skb, but
not enough to overcome the minimum required by the host to proceed.
As the refill job would only reschedule itself if it failed completely
to allocate any skbs, this would lead to an RX stall.
The following patch removes this stall possibility by always
rescheduling the refill job until the ring is totally refilled.
Testing has shown that the RX stall no longer occurs whereas
previously it would occur within a day.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings [Mon, 25 Jan 2010 23:49:59 +0000 (15:49 -0800)]
sfc: Use fixed-size buffers for MCDI NVRAM requests
The low-level MCDI code always uses 32-bit MMIO operations, and
callers must pad input and output buffers to multiples of 4 bytes.
The MCDI NVRAM functions are not doing this. Also, their buffers are
declared as variable-length arrays with no explicit maximum length.
Switch to a fixed buffer size based on the chunk size used by the
MTD driver (which is a multiple of 4).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Guido Barzini [Mon, 25 Jan 2010 23:49:19 +0000 (15:49 -0800)]
sfc: Add workspace for GMAC bug workaround to MCDI MAC_STATS buffer
Due to a hardware bug in the SFC9000 family, the firmware must
transfer raw GMAC statistics to host memory before aggregating them
into the cooked (speed-independent) MAC statistics. Extend the stats
buffer to support this.
The length of the buffer is explicit in the MAC_STATS command, so this
change is backward-compatible on both sides.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger [Mon, 25 Jan 2010 23:47:50 +0000 (15:47 -0800)]
tcp_probe: avoid modulus operation and wrap fix
By rounding up the buffer size to power of 2, several expensive
modulus operations can be avoided. This patch also solves a bug where
the gap need when ring gets full was not being accounted for.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Breno Leitao [Mon, 25 Jan 2010 23:46:58 +0000 (15:46 -0800)]
qlge: Only free resources if they were allocated
Currently qlge tries to release regions even if they were not allocated.
This causes messages like the following in the kernel log
Trying to free nonexistent resource <
00000000006af400-
00000000006af4ff>
Trying to free nonexistent resource <
00003c04ff9f4000-
00003c04ff9f7fff>
Trying to free nonexistent resource <
00003c04ffc00000-
00003c04ffcfffff>
This patch fixes the goto logic in order to not release the resources
if they were not allocated.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Felix Fietkau [Sat, 23 Jan 2010 19:04:18 +0000 (20:04 +0100)]
ath9k: fix eeprom INI values override for 2GHz-only cards
Among other changes, this commit:
commit
06d0f0663e11cab4ec5f2c143a118d71a12fbbe9
Author: Sujith <Sujith.Manoharan@atheros.com>
Date: Thu Feb 12 10:06:45 2009 +0530
ath9k: Enable Fractional N mode
changed the hw attach code to fix up initialization values only for
dual band devices, however the commit message did not give a reason as
to why this would be useful or necessary.
According to tests by Jorge Boncompte, this breaks at least some
2GHz-only cards, so the code should be changed back to the
unconditional INI fixup.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Jorge Boncompte <jorge@dti2.net>
Cc: stable@kernel.org
Tested-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 22 Jan 2010 22:22:34 +0000 (14:22 -0800)]
iwlwifi: fix pointer signedness warning
There are a few station addresses that are
char *, instead of the normal u8 *; gcc
gives pointer signedness warnings for some
of those, so use u8 * consistently.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Alexey Dobriyan [Mon, 25 Jan 2010 06:47:53 +0000 (22:47 -0800)]
netns xfrm: deal with dst entries in netns
GC is non-existent in netns, so after you hit GC threshold, no new
dst entries will be created until someone triggers cleanup in init_net.
Make xfrm4_dst_ops and xfrm6_dst_ops per-netns.
This is not done in a generic way, because it woule waste
(AF_MAX - 2) * sizeof(struct dst_ops) bytes per-netns.
Reorder GC threshold initialization so it'd be done before registering
XFRM policies.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
stephen hemminger [Sun, 24 Jan 2010 18:46:06 +0000 (18:46 +0000)]
sky2: revert config space change
Obviously, this register had some other impact that is causing
the regression. Either it is masking some other access or needs
to be reset in some path.
Either, way it is best to just revert the change for 2.6.33
This reverts commit
166a0fd4c788ec7f10ca8194ec6d526afa12db75.
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet [Mon, 25 Jan 2010 03:52:24 +0000 (19:52 -0800)]
vlan: fix vlan_skb_recv()
Bruno Prémont found commit
9793241fe92f7d930
(vlan: Precise RX stats accounting) added a regression for non
hw accelerated vlans.
[ 26.390576] BUG: unable to handle kernel NULL pointer dereference at (null)
[ 26.396369] IP: [<
df856b89>] vlan_skb_recv+0x89/0x280 [8021q]
vlan_dev_info() was used with original device, instead of
skb->dev. Also spotted by Américo Wang.
Reported-By: Bruno Prémont <bonbons@linux-vserver.org>
Tested-By: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey Dobriyan [Sat, 23 Jan 2010 13:37:10 +0000 (13:37 +0000)]
netns xfrm: fix "ip xfrm state|policy count" misreport
"ip xfrm state|policy count" report SA/SP count from init_net,
not from netns of caller process.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mike McCormack [Sat, 23 Jan 2010 10:09:26 +0000 (02:09 -0800)]
sky2: Enable/disable WOL per hardware device
Y2_HW_WOL_ON/Y2_HW_WOL_OFF should be set and cleared per chip,
not per port. On dual port cards, Y2_HW_WOL_ON should be
enabled if either sky2 port has WOL enabled.
Found while reviewing code for a WOL regression, though this is
probably not the cause of the regression.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sridhar Samudrala [Sat, 23 Jan 2010 10:02:21 +0000 (02:02 -0800)]
net: Fix IPv6 GSO type checks in Intel ethernet drivers
Found this problem when testing IPv6 from a KVM guest to a remote
host via e1000e device on the host.
The following patch fixes the check for IPv6 GSO packet in Intel
ethernet drivers to use skb_is_gso_v6(). SKB_GSO_DODGY is also set
when packets are forwarded from a guest.
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck [Sat, 23 Jan 2010 09:35:00 +0000 (01:35 -0800)]
igb/igbvf: cleanup exception handling in tx_map_adv
After removing the skb_dma_map/unmap calls the exception handling in
igb_tx_map_adv is not correct. The issue is that the count value was not
being correctly handled so as a result we were not rewinding the ring as
back as we should have been.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher [Sat, 23 Jan 2010 09:20:22 +0000 (01:20 -0800)]
MAINTAINERS: Add Intel igbvf maintainer
Add igbvf to the list of supported Intel drivers and Alex to the list of
maintainers.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesse Brandeburg [Fri, 22 Jan 2010 22:56:16 +0000 (22:56 +0000)]
e1000/e1000e: don't use small hardware rx buffers
When testing the "e1000: enhance frame fragment detection" (and e1000e)
patches we found some bugs with reducing the MTU size. The 1024 byte
descriptor used with the 1000 mtu test also (re) introduced the
(originally) reported bug, and causes us to need the e1000_clean_tx_irq
"enhance frame fragment detection" fix.
So what has occured here is that 2.6.32 is only vulnerable for mtu <
1500 due to the jumbo specific routines in both e1000 and e1000e.
So, 2.6.32 needs the 2kB buffer len fix for those smaller MTUs, but
is not vulnerable to the original issue reported. It has been pointed
out that this vulnerability needs to be patched in older kernels that
don't have the e1000 jumbo routine. Without the jumbo routines, we
need the "enhance frame fragment detection" fix the e1000, old
e1000e is only vulnerable for < 1500 mtu, and needs a similar
fix. We split the patches up to provide easy backport paths.
There is only a slight bit of extra code when this fix and the
original "enhance frame fragment detection" fixes are applied, so
please apply both, even though it is a bit of overkill.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ken Kawasaki [Fri, 22 Jan 2010 11:56:25 +0000 (11:56 +0000)]
fmvj18x_cs: add new id (Panasonic lan & modem card)
fmvj18x_cs, serial_cs:
add new id
Panasonic lan & modem card (model name:AL-VML101)
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sathya Perla [Thu, 21 Jan 2010 22:51:36 +0000 (22:51 +0000)]
be2net: swap only first 2 fields of mcc_wrb
Only the first two fields of mcc wrb - embedded, payload_len
need to be cpu_to_le32() swapped while issuing a cmd to the hw.
The fields tag0, tag1 are opaque and returned back to cpu as is...
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ron Murray [Tue, 19 Jan 2010 08:02:48 +0000 (08:02 +0000)]
Please add support for Microsoft MN-120 PCMCIA network card
Please add support for Microsoft MN-120 PCMCIA network card. It's an
old card, I know, but adding support is very easy. You just need to
get tulip_core.c to recognise its vendor/device ID.
Patch for kernel 2.6.32.4 (and many previous) attached.
.....Ron Murray
Signed-off-by: Ron Murray <rjmx@rjmx.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 23 Jan 2010 09:08:39 +0000 (01:08 -0800)]
Merge branch 'linux-2.6.33.y' of git://git./linux/kernel/git/inaky/wimax
David S. Miller [Sat, 23 Jan 2010 06:45:46 +0000 (22:45 -0800)]
Merge branch 'master' of /home/davem/src/GIT/linux-2.6/
Sathya Perla [Fri, 22 Jan 2010 06:52:08 +0000 (22:52 -0800)]
be2net: fix bug in rx page posting
Pages are posted to the rxq in such a way that more than one frag
can share the page. The last frag that uses the page unmaps the
page. In the case when a page is not fully used (due to lack of space in rxq)
the last frag that uses the page is not being set as a "last_page_user";
instead, the next frag in the rxq is incorrectly being set.
The fix has also been tested on ppc64 with 64k pages...
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Inaky Perez-Gonzalez [Wed, 20 Jan 2010 20:41:13 +0000 (12:41 -0800)]
wimax/i2400m: Add support for more i6x50 SKUs
The Intel WiMax Wireless Link 6050 can show under more than one USB
ID. Add support for all, introducing a generic flag (i2400mu->i6050)
that denotes a 6x50 based device.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Linus Torvalds [Thu, 21 Jan 2010 23:31:35 +0000 (15:31 -0800)]
Linux 2.6.33-rc5
Linus Torvalds [Thu, 21 Jan 2010 16:50:04 +0000 (08:50 -0800)]
Merge branch 'perf-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf: x86: Add support for the ANY bit
perf: Change the is_software_event() definition
perf: Honour event state for aux stream data
perf: Fix perf_event_do_pending() fallback callsite
perf kmem: Print usage help for unknown commands
perf kmem: Increase "Hit" column length
hw-breakpoints, perf: Fix broken mmiotrace due to dr6 by reference change
perf timechart: Use tid not pid for COMM change
Linus Torvalds [Thu, 21 Jan 2010 16:49:52 +0000 (08:49 -0800)]
Merge branch 'sched-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Reassign prev and switch_count when reacquire_kernel_lock() fail
sched: Fix vmark regression on big machines
Linus Torvalds [Thu, 21 Jan 2010 15:42:59 +0000 (07:42 -0800)]
Merge branch 'upstream-linus' of git://git./linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: retry FS IOs even if it has failed with AC_ERR_INVALID
Linus Torvalds [Thu, 21 Jan 2010 15:37:20 +0000 (07:37 -0800)]
Merge git://git./linux/kernel/git/gregkh/tty-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
tty: fix race in tty_fasync
serial: serial_cs: oxsemi quirk breaks resume
serial: imx: bit &/| confusion
serial: Fix crash if the minimum rate of the device is > 9600 baud
serial-core: resume serial hardware with no_console_suspend
serial: 8250_pnp: use wildcard for serial Wacom tablets
nozomi: quick fix for the close/close bug
compat_ioctl: Supress "unknown cmd" message on serial /dev/console
Linus Torvalds [Thu, 21 Jan 2010 15:36:55 +0000 (07:36 -0800)]
Merge git://git./linux/kernel/git/gregkh/staging-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
Staging: hv: fix smp problems in the hyperv core code
Staging: et131x: Fix 2.6.33rc1 regression in et131x
Staging: asus_oled: fix oops in 2.6.32.2
Linus Torvalds [Thu, 21 Jan 2010 15:36:31 +0000 (07:36 -0800)]
Merge git://git./linux/kernel/git/gregkh/driver-core-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
Revert "sysdev: fix prototype for memory_sysdev_class show/store functions"
driver-core: fix devtmpfs crash on s390
Linus Torvalds [Thu, 21 Jan 2010 15:35:43 +0000 (07:35 -0800)]
Merge git://git./linux/kernel/git/gregkh/usb-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: isp1362: fix build failure on ARM systems via irq_flags cleanup
USB: isp1362: better 64bit printf warning fixes
USB: fix usbstorage for 2770:915d delivers no FAT
USB: Fix level of isp1760 Reloading ptd error message
USB: FHCI: avoid NULL pointer dereference
USB: Fix duplicate sysfs problem after device reset.
USB: add speed values for USB 3.0 and wireless controllers
USB: add missing delay during remote wakeup
USB: EHCI & UHCI: fix race between root-hub suspend and port resume
USB: EHCI: fix handling of unusual interrupt intervals
USB: Don't use GFP_KERNEL while we cannot reset a storage device
USB: fix bitmask merge error
usb: serial: fix memory leak in generic driver
USB: serial: fix USB serial fix kfifo_len locking
Linus Torvalds [Thu, 21 Jan 2010 15:32:11 +0000 (07:32 -0800)]
Merge branch 'for-linus' of git://git.kernel.dk/linux-2.6-block
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
fs/bio.c: fix shadows sparse warning
drbd: The kernel code is now equivalent to out of tree release 8.3.7
drbd: Allow online resizing of DRBD devices while peer not reachable (needs to be explicitly forced)
drbd: Don't go into StandAlone mode when authentification failes because of network error
drivers/block/drbd/drbd_receiver.c: correct NULL test
cfq-iosched: Respect ioprio_class when preempting
genhd: overlapping variable definition
block: removed unused as_io_context
DM: Fix device mapper topology stacking
block: bdev_stack_limits wrapper
block: Fix discard alignment calculation and printing
block: Correct handling of bottom device misaligment
drbd: check on CONFIG_LBDAF, not LBD
drivers/block/drbd: Correct NULL test
drbd: Silenced an assert that could triggered after changing write ordering method
drbd: Kconfig fix
drbd: Fix for a race between IO and a detach operation [Bugz 262]
drbd: Use drbd_crypto_is_hash() instead of an open coded check
Linus Torvalds [Thu, 21 Jan 2010 15:29:36 +0000 (07:29 -0800)]
Merge branch 'release' of git://git./linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (23 commits)
ACPI: delete acpi_processor_power_verify_c2()
ACPI: allow C3 > 1000usec
ACPI: enable C2 and Turbo-mode on Nehalem notebooks on A/C
ACPI: power_meter: remove double kfree()
ACPI: processor: restrict early _PDC to opt-in platforms
ACPI: Fix unused variable warning in sbs.c
acpi: make ACPI device id constant
sony-laptop - fix using of uninitialized variable
ACPI: Fix section mismatch error for acpi_early_processor_set_pdc()
eeepc-laptop: disable wireless hotplug for 1201N
eeepc-laptop: add hotplug_disable parameter
eeepc-laptop: switch to using sparse keymap library
eeepc-laptop: dmi blacklist to disable pci hotplug code
eeepc-laptop: disable cpu speed control on EeePC 701
ACPI: don't cond_resched if irq is disabled
ACPI: Remove unnecessary cast.
ACPI: Advertise to BIOS in _OSC: _OST on _PPC changes
ACPI: EC: Add wait for irq storm
ACPI: SBS: Move SBS HC callback to faster Notify queue
x86, ACPI: delete acpi_boot_table_init() return value
...
Linus Torvalds [Thu, 21 Jan 2010 15:28:54 +0000 (07:28 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/ecryptfs/ecryptfs-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ecryptfs/ecryptfs-2.6:
ecryptfs: use after free
ecryptfs: Eliminate useless code
ecryptfs: fix interpose/interpolate typos in comments
ecryptfs: pass matching flags to interpose as defined and used there
ecryptfs: remove unnecessary d_drop calls in ecryptfs_link
ecryptfs: don't ignore return value from lock_rename
ecryptfs: initialize private persistent file before dereferencing pointer
eCryptfs: Remove mmap from directory operations
eCryptfs: Add getattr function
eCryptfs: Use notify_change for truncating lower inodes
Linus Torvalds [Thu, 21 Jan 2010 15:28:05 +0000 (07:28 -0800)]
Merge git://git./linux/kernel/git/mason/btrfs-unstable
* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
Btrfs: fix possible panic on unmount
Btrfs: deal with NULL acl sent to btrfs_set_acl
Btrfs: fix regression in orphan cleanup
Btrfs: Fix race in btrfs_mark_extent_written
Btrfs, fix memory leaks in error paths
Btrfs: align offsets for btrfs_ordered_update_i_size
btrfs: fix missing last-entry in readdir(3)
Yongseok Koh [Tue, 19 Jan 2010 08:33:49 +0000 (17:33 +0900)]
vmalloc: remove BUG_ON due to racy counting of VM_LAZY_FREE
In free_unmap_area_noflush(), va->flags is marked as VM_LAZY_FREE first, and
then vmap_lazy_nr is increased atomically.
But, in __purge_vmap_area_lazy(), while traversing of vmap_are_list, nr
is counted by checking VM_LAZY_FREE is set to va->flags. After counting
the variable nr, kernel reads vmap_lazy_nr atomically and checks a
BUG_ON condition whether nr is greater than vmap_lazy_nr to prevent
vmap_lazy_nr from being negative.
The problem is that, if interrupted right after marking VM_LAZY_FREE,
increment of vmap_lazy_nr can be delayed. Consequently, BUG_ON
condition can be met because nr is counted more than vmap_lazy_nr.
It is highly probable when vmalloc/vfree are called frequently. This
scenario have been verified by adding delay between marking VM_LAZY_FREE
and increasing vmap_lazy_nr in free_unmap_area_noflush().
Even the vmap_lazy_nr is for checking high watermark, it never be the
strict watermark. Although the BUG_ON condition is to prevent
vmap_lazy_nr from being negative, vmap_lazy_nr is signed variable. So,
it could go down to negative value temporarily.
Consequently, removing the BUG_ON condition is proper.
A possible BUG_ON message is like the below.
kernel BUG at mm/vmalloc.c:517!
invalid opcode: 0000 [#1] SMP
EIP: 0060:[<
c04824a4>] EFLAGS:
00010297 CPU: 3
EIP is at __purge_vmap_area_lazy+0x144/0x150
EAX:
ee8a8818 EBX:
c08e77d4 ECX:
e7c7ae40 EDX:
c08e77ec
ESI:
000081fe EDI:
e7c7ae60 EBP:
e7c7ae64 ESP:
e7c7ae3c
DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
Call Trace:
[<
c0482ad9>] free_unmap_vmap_area_noflush+0x69/0x70
[<
c0482b02>] remove_vm_area+0x22/0x70
[<
c0482c15>] __vunmap+0x45/0xe0
[<
c04831ec>] vmalloc+0x2c/0x30
Code: 8d 59 e0 eb 04 66 90 89 cb 89 d0 e8 87 fe ff ff 8b 43 20 89 da 8d 48 e0 8d 43 20 3b 04 24 75 e7 fe 05 a8 a5 a3 c0 e9 78 ff ff ff <0f> 0b eb fe 90 8d b4 26 00 00 00 00 56 89 c6 b8 ac a5 a3 c0 31
EIP: [<
c04824a4>] __purge_vmap_area_lazy+0x144/0x150 SS:ESP 0068:
e7c7ae3c
[ See also http://marc.info/?l=linux-kernel&m=
126335856228090&w=2 ]
Signed-off-by: Yongseok Koh <yongseok.koh@samsung.com>
Reviewed-by: Minchan Kim <minchan.kim@gmail.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 21 Jan 2010 15:16:27 +0000 (07:16 -0800)]
Merge branch 'sh/for-2.6.33' of git://git./linux/kernel/git/lethal/sh-2.6
* 'sh/for-2.6.33' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh64: wire up sys_accept4.
sh: unwire sys_recvmmsg.
sh: ms7724: Correct sh-eth EEPROM polling timeout.
Linus Torvalds [Thu, 21 Jan 2010 15:15:10 +0000 (07:15 -0800)]
Merge master.kernel.org:/home/rmk/linux-2.6-arm
* master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 5888/1: arm: Update comments in cacheflush.h and remove unnecessary V6 and V7 comments
ARM: 5886/1: arm: Fix cpu_proc_fin() for proc-v7.S and make kexec work
ARM: 5885/1: arm: Flush TLB entries in setup_mm_for_reboot()
ARM: 5884/1: arm: Fix DCC console for v7
ARM: 5883/1: Revert "disable NX support for OABI-supporting kernels"
ARM: 5882/1: ARM: Fix uncompress code compile for different defines of flush(void)
ARM: fix badly placed mach/plat entries in Kconfig & Makefile
Stephane Eranian [Mon, 18 Jan 2010 08:58:01 +0000 (10:58 +0200)]
perf: x86: Add support for the ANY bit
Propagate the ANY bit into the fixed counter config for v3 and higher.
Signed-off-by: Stephane Eranian <eranian@google.com>
[a.p.zijlstra@chello.nl: split from larger patch]
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <
4b5430c6.
0f975e0a.1bf9.
ffff85fe@mx.google.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Peter Zijlstra [Mon, 18 Jan 2010 13:02:16 +0000 (14:02 +0100)]
perf: Change the is_software_event() definition
The is_software_event() definition always confuses me because its an
exclusive expression, make it an inclusive one.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Peter Zijlstra [Mon, 18 Jan 2010 08:12:32 +0000 (09:12 +0100)]
perf: Honour event state for aux stream data
Anton reported that perf record kept receiving events even after calling
ioctl(PERF_EVENT_IOC_DISABLE). It turns out that FORK,COMM and MMAP
events didn't respect the disabled state and kept flowing in.
Reported-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Tested-by: Anton Blanchard <anton@samba.org>
LKML-Reference: <
1263459187.4244.265.camel@laptop>
CC: stable@kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Peter Zijlstra [Mon, 18 Jan 2010 08:08:26 +0000 (09:08 +0100)]
perf: Fix perf_event_do_pending() fallback callsite
Paul questioned the context in which we should call
perf_event_do_pending(). After looking at that I found that it should be
called from IRQ context these days, however the fallback call-site is
placed in softirq context. Ammend this by placing the callback in the IRQ
timer path.
Reported-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <
1263374859.4244.192.camel@laptop>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Yong Zhang [Mon, 11 Jan 2010 06:21:25 +0000 (14:21 +0800)]
sched: Reassign prev and switch_count when reacquire_kernel_lock() fail
Assume A->B schedule is processing, if B have acquired BKL before and it
need reschedule this time. Then on B's context, it will go to
need_resched_nonpreemptible for reschedule. But at this time, prev and
switch_count are related to A. It's wrong and will lead to incorrect
scheduler statistics.
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <2674af741001102238w7b0ddcadref00d345e2181d11@mail.gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Mike Galbraith [Mon, 4 Jan 2010 13:44:56 +0000 (14:44 +0100)]
sched: Fix vmark regression on big machines
SD_PREFER_SIBLING is set at the CPU domain level if power saving isn't
enabled, leading to many cache misses on large machines as we traverse
looking for an idle shared cache to wake to. Change the enabler of
select_idle_sibling() to SD_SHARE_PKG_RESOURCES, and enable same at the
sibling domain level.
Reported-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <
1262612696.15495.15.camel@marge.simson.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Jesse Brandeburg [Tue, 19 Jan 2010 14:15:59 +0000 (14:15 +0000)]
e1000e: enhance frame fragment detection
Originally patched by Neil Horman <nhorman@tuxdriver.com>
e1000e could with a jumbo frame enabled interface, and packet split disabled,
receive a packet that would overflow a single rx buffer. While in practice
very hard to craft a packet that could abuse this, it is possible.
this is related to CVE-2009-4538
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesse Brandeburg [Tue, 19 Jan 2010 14:15:38 +0000 (14:15 +0000)]
e1000: enhance frame fragment detection
Originally From: Neil Horman <nhorman@tuxdriver.com>
Modified by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Hey all-
A security discussion was recently given:
http://events.ccc.de/congress/2009/Fahrplan//events/3596.en.html
And a patch that I submitted awhile back was brought up. Apparently some of
their testing revealed that they were able to force a buffer fragment in e1000
in which the trailing fragment was greater than 4 bytes. As a result the
fragment check I introduced failed to detect the fragement and a partial
invalid frame was passed up into the network stack. I've written this patch
to correct it. I'm in the process of testing it now, but it makes good
logical sense to me. Effectively it maintains a per-adapter state variable
which detects a non-EOP frame, and discards it and subsequent non-EOP frames
leading up to _and_ _including_ the next positive-EOP frame (as it is by
definition the last fragment). This should prevent any and all partial frames
from entering the network stack from e1000.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Roel Kluin [Tue, 19 Jan 2010 14:21:45 +0000 (14:21 +0000)]
e1000/e1000e/igb/igbvf/ixgb/ixgbe: Fix tests of unsigned in *_tx_map()
The variable count and i are unsigned so the (<|>=)0 tests do not work.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lothar Wassmann [Fri, 15 Jan 2010 19:42:02 +0000 (14:42 -0500)]
USB: isp1362: fix build failure on ARM systems via irq_flags cleanup
There was some left over #ifdef ARM logic that is outdated but no one
really noticed. So instead of relying on this tricky logic, properly
load and utilize the platform irq_flags resources.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Lothar Wassmann <LW@KARO-electronics.de>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Lothar Wassmann [Fri, 15 Jan 2010 13:04:55 +0000 (08:04 -0500)]
USB: isp1362: better 64bit printf warning fixes
Some hosts that treat the return value of sizeof differently from unsigned
long might still hit warnings. So use %zu for sizeof() values. This is a
better version of the previous commit
b0a9cf297e58721933.
Signed-off-by: Lothar Wassmann <LW@KARO-electronics.de>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Ryan May [Wed, 6 Jan 2010 16:09:25 +0000 (10:09 -0600)]
USB: fix usbstorage for 2770:915d delivers no FAT
Resolves kernel.org bug 14914.
Remove entry for 2770:915d (usb digital camera with mass storage
support) from unusual_devs.h. The fix triggered by the entry causes
the file system on the camera to be completely inaccessible (no
partition table, the device is not mountable).
The patch works, but let me clarify a few things about it. All the
patch does is remove the entry for this device from the
drivers/usb/storage/unusual_devs.h, which is supposed to help with a
problem with the device's reported size (I think). I'm pretty sure it
was originally added for a reason, so I'm not sure removing it won't
cause other problems to reappear. Also, I should note that this
unusual_devs.h entry was present (and activating workarounds) in
2.6.29, but in that version everything works fine. Starting with
2.6.30, things no longer work.
Signed-off-by: Ryan May <rmay31@gmail.com>
Cc: Rohan Hart <rohan.hart17@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Colin Tuckley [Thu, 7 Jan 2010 11:22:47 +0000 (11:22 +0000)]
USB: Fix level of isp1760 Reloading ptd error message
This error message is not actually an error, it's an information
message. It is triggered when a transfer which ended in a NAQ is
retried successfully by the hardware.
Signed-off-by: Colin Tuckley <colin.tuckley@arm.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alexander Beregalov [Thu, 7 Jan 2010 01:17:32 +0000 (04:17 +0300)]
USB: FHCI: avoid NULL pointer dereference
Assign fhci only if usb is not NULL.
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sarah Sharp [Wed, 6 Jan 2010 18:16:51 +0000 (10:16 -0800)]
USB: Fix duplicate sysfs problem after device reset.
Borislav Petkov reports issues with duplicate sysfs endpoint files after a
resume from a hibernate. It turns out that the code to support alternate
settings under xHCI has issues when a device with a non-default alternate
setting is reset during the hibernate:
[ 427.681810] Restarting tasks ...
[ 427.681995] hub 1-0:1.0: state 7 ports 6 chg 0004 evt 0000
[ 427.682019] usb usb3: usb resume
[ 427.682030] ohci_hcd 0000:00:12.0: wakeup root hub
[ 427.682191] hub 1-0:1.0: port 2, status 0501, change 0000, 480 Mb/s
[ 427.682205] usb 1-2: usb wakeup-resume
[ 427.682226] usb 1-2: finish reset-resume
[ 427.682886] done.
[ 427.734658] ehci_hcd 0000:00:12.2: port 2 high speed
[ 427.734663] ehci_hcd 0000:00:12.2: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT
[ 427.746682] hub 3-0:1.0: hub_reset_resume
[ 427.746693] hub 3-0:1.0: trying to enable port power on non-switchable hub
[ 427.786715] usb 1-2: reset high speed USB device using ehci_hcd and address 2
[ 427.839653] ehci_hcd 0000:00:12.2: port 2 high speed
[ 427.839666] ehci_hcd 0000:00:12.2: GetStatus port 2 status 001005 POWER sig=se0 PE CONNECT
[ 427.847717] ohci_hcd 0000:00:12.0: GetStatus roothub.portstatus [1] = 0x00010100 CSC PPS
[ 427.915497] hub 1-2:1.0: remove_intf_ep_devs: if:
ffff88022f9e8800 ->ep_devs_created: 1
[ 427.915774] hub 1-2:1.0: remove_intf_ep_devs: bNumEndpoints: 1
[ 427.915934] hub 1-2:1.0: if:
ffff88022f9e8800: endpoint devs removed.
[ 427.916158] hub 1-2:1.0: create_intf_ep_devs: if:
ffff88022f9e8800 ->ep_devs_created: 0, ->unregistering: 0
[ 427.916434] hub 1-2:1.0: create_intf_ep_devs: bNumEndpoints: 1
[ 427.916609] ep_81: create, parent hub
[ 427.916632] ------------[ cut here ]------------
[ 427.916644] WARNING: at fs/sysfs/dir.c:477 sysfs_add_one+0x82/0x96()
[ 427.916649] Hardware name: System Product Name
[ 427.916653] sysfs: cannot create duplicate filename '/devices/pci0000:00/0000:00:12.2/usb1/1-2/1-2:1.0/ep_81'
[ 427.916658] Modules linked in: binfmt_misc kvm_amd kvm powernow_k8 cpufreq_ondemand cpufreq_powersave cpufreq_userspace freq_table cpufreq_conservative ipv6 vfat fat
+8250_pnp 8250 pcspkr ohci_hcd serial_core k10temp edac_core
[ 427.916694] Pid: 278, comm: khubd Not tainted
2.6.33-rc2-00187-g08d869a-dirty #13
[ 427.916699] Call Trace:
The problem is caused by a mismatch between the USB core's view of the
device state and the USB device and xHCI host's view of the device state.
After the device reset and re-configuration, the device and the xHCI host
think they are using alternate setting 0 of all interfaces. However, the
USB core keeps track of the old state, which may include non-zero
alternate settings. It uses intf->cur_altsetting to keep the endpoint
sysfs files for the old state across the reset.
The bandwidth allocation functions need to know what the xHCI host thinks
the current alternate settings are, so original patch set
intf->cur_altsetting to the alternate setting 0. This caused duplicate
endpoint files to be created.
The solution is to not set intf->cur_altsetting before calling
usb_set_interface() in usb_reset_and_verify_device(). Instead, we add a
new flag to struct usb_interface to tell usb_hcd_alloc_bandwidth() to use
alternate setting 0 as the currently installed alternate setting.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Borislav Petkov <petkovbb@googlemail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman [Thu, 14 Jan 2010 18:33:19 +0000 (10:33 -0800)]
USB: add speed values for USB 3.0 and wireless controllers
These controllers say "unknown" for their speed in sysfs, which
obviously isn't correct.
Reported-by: Kurt Garloff <garloff@novell.com>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: David Vrabel <david.vrabel@csr.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Fri, 8 Jan 2010 16:18:38 +0000 (11:18 -0500)]
USB: add missing delay during remote wakeup
This patch (as1330) fixes a bug in khbud's handling of remote
wakeups. When a device sends a remote-wakeup request, the parent hub
(or the host controller driver, for directly attached devices) begins
the resume sequence and notifies khubd when the sequence finishes. At
this point the port's SUSPEND feature is automatically turned off.
However the device needs an additional 10-ms resume-recovery time
(TRSMRCY in the USB spec). Khubd does not wait for this delay if the
SUSPEND feature is off, and as a result some devices fail to behave
properly following a remote wakeup. This patch adds the missing
delay to the remote-wakeup path.
It also extends the resume-signalling delay used by ehci-hcd and
uhci-hcd from 20 ms (the value in the spec) to 25 ms (the value we use
for non-remote-wakeup resumes). The extra time appears to help some
devices.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Cc: Rickard Bellini <rickard.bellini@ericsson.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Fri, 8 Jan 2010 16:18:20 +0000 (11:18 -0500)]
USB: EHCI & UHCI: fix race between root-hub suspend and port resume
This patch (as1321) fixes a problem with EHCI and UHCI root-hub
suspends: If the suspend occurs while a port is trying to resume, the
resume doesn't finish and simply gets lost. When remote wakeup is
enabled, this is undesirable behavior.
The patch checks first to see if any port resumes are in progress, and
if they are then it fails the root-hub suspend with -EBUSY.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Fri, 8 Jan 2010 16:17:55 +0000 (11:17 -0500)]
USB: EHCI: fix handling of unusual interrupt intervals
This patch (as1320) fixes two problems related to interrupt-URB
scheduling in ehci-hcd.
URBs with an interval of 2 or 4 microframes aren't handled.
For the time being, the patch reduces to interval to 1 uframe.
URBs are constrained to have an interval no larger than 1024
frames by usb_submit_urb(). But some EHCI controllers allow
use of a schedule as short as 256 frames; for these
controllers we may have to decrease the interval to the
actual schedule length.
The second problem isn't very significant since few devices expose
interrupt endpoints with an interval larger than 256 frames. But the
first problem is critical; it will prevent the kernel from working
with devices having interrupt intervals of 2 or 4 uframes.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Tested-by: Glynn Farrow <farrowg@sg.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Oliver Neukum [Tue, 12 Jan 2010 11:32:50 +0000 (12:32 +0100)]
USB: Don't use GFP_KERNEL while we cannot reset a storage device
Memory allocations with GFP_KERNEL can cause IO to a storage
device which can fail resulting in a need to reset the device.
Therefore GFP_KERNEL cannot be safely used between usb_lock_device()
and usb_unlock_device(). Replace by GFP_NOIO.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Stern [Wed, 23 Dec 2009 04:16:32 +0000 (23:16 -0500)]
USB: fix bitmask merge error
This patch adds a mask bit which was mistakenly omitted from the
as1311 patch (usb-storage: add BAD_SENSE flag).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Johan Hovold [Wed, 6 Jan 2010 23:48:42 +0000 (15:48 -0800)]
usb: serial: fix memory leak in generic driver
Fix a regression introduced by commit
715b1dc01fe44537e8fce9566e4bb48d6821d84b ("USB: usb_debug,
usb_generic_serial: implement multi urb write").
URB transfer buffer was never freed when using multi-urb writes.
Currently the only driver enabling multi-urb writes is usb_debug.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: Greg KH <greg@kroah.com>
Acked-by: Jason Wessel <jason.wessel@windriver.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Stefani Seibold [Tue, 5 Jan 2010 13:30:31 +0000 (14:30 +0100)]
USB: serial: fix USB serial fix kfifo_len locking
This patch fix a possible race bug in drivers/usb/serial/generic with
the new kfifo API.
Please apply it to the 2.6.33-rc* tree.
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman [Fri, 8 Jan 2010 17:06:40 +0000 (09:06 -0800)]
Staging: hv: fix smp problems in the hyperv core code
This fixes a number of SMP problems that were in the hyperv core code.
Patch originally written by K. Y. Srinivasan <ksrinivasan@novell.com>
but forward ported to the latest in-kernel code and tweaked slightly by
me.
Novell, Inc. hereby disclaims all copyright in any derivative work
copyright associated with this patch.
Signed-off-by: K. Y. Srinivasan <ksrinivasan@novell.com>
Cc: Hank Janssen <hjanssen@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>.
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Cox [Wed, 6 Jan 2010 14:01:26 +0000 (14:01 +0000)]
Staging: et131x: Fix 2.6.33rc1 regression in et131x
et131x: Fix 12bit wrapping
From: Alan Cox <alan@linux.intel.com>
The 12bit wrap logic conversion is wrong and this shows up for some
memory sizes and layouts of card. Patch it up for now, once the kernel
view of status is cleaned up it'll become two variables and a lot saner.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Eugeni Dodonov [Wed, 23 Dec 2009 12:27:22 +0000 (10:27 -0200)]
Staging: asus_oled: fix oops in 2.6.32.2
After updating to 2.6.32 kernel, I started experiencing Oopses caused by
the asus_oled module. After quick investigation, I wrapped this simple
patch which fixes an Oops in by asus_oled module on 2.6.32.2 kernel,
caused by incorrect usage of strict_strtoul function call within
set_enabled and set_disabled functions. This can be triggered by simple
running the userspace client for asus_old (e.g., 'asusoled -e' or
'asusoled -d').
Signed-off-by: Eugeni Dodonov <eugeni@mandriva.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman [Thu, 17 Dec 2009 15:07:19 +0000 (07:07 -0800)]
tty: fix race in tty_fasync
We need to keep the lock held over the call to __f_setown() to
prevent a PID race.
Thanks to Al Viro for pointing out the problem, and to Travis for
making us look here in the first place.
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Tavis Ormandy <taviso@google.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Julien Tinnes <jln@google.com>
Cc: Matt Mackall <mpm@selenic.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Pavel Machek [Wed, 9 Dec 2009 20:31:31 +0000 (12:31 -0800)]
serial: serial_cs: oxsemi quirk breaks resume
Quirk is applied on all cards with given manfid (is it that correct?).
Unfortunately, that quirk breaks resume on zaurus with billionton
bluetooth card inserted: c950ctrl is 0 and outb() faults.
I believe it is simply not a multiport card. (info->multi == 1). ...
... confirmed by printks.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Roel Kluin [Wed, 9 Dec 2009 20:31:36 +0000 (12:31 -0800)]
serial: imx: bit &/| confusion
Since UCR1_UARTEN is defined 1, the port was always treated as enabled.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Acked-by: Oskar Schirmer <os@emlix.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Fabian Godehardt <fg@emlix.com>
Cc: Daniel Glöckner <dg@emlix.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Cox [Mon, 4 Jan 2010 16:26:21 +0000 (16:26 +0000)]
serial: Fix crash if the minimum rate of the device is > 9600 baud
In that situation if the old rate is invalid and the new rate is invalid
and the chip cannot do 9600 baud we report zero, which makes all the
drivers explode.
Instead force the rate based on min/max
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Stanislav Brabec [Wed, 2 Dec 2009 15:20:56 +0000 (16:20 +0100)]
serial-core: resume serial hardware with no_console_suspend
Perform a tricky suspend/resume even with no_console_suspend.
With no_console_suspend, kernel skips serial port suspend/resume and the
serial hardware may remain in undefined state after resume. It actually
happens on devices that don't have BIOS that handle serial
initialization. It makes impossible to use serial console after resume.
Devices affected by this problem include:
Sharp Zaurus devices
Several PXA based ARM embedded boards
The patch does:
- Save the hardware state
- Perform buffer flush in time of its suspend call
- Tell the driver that port is suspended
- But still accept new data
- And keep console hardware in state that allows to send them
It allows to capture late console messages without breaking console
after resume.
This is just a resend of a patch discussed in these threads, as the
patch was not yet applied.
"Possible suspend/resume regression in .32-rc?" (Nov 1-5, 2009, ARM
list, later LKML)
"serial-core: resume serial hardware with no_console_suspend" (Sep
15-Oct 18, 2009, LKML & ARM lists)
Signed-off-by: Stanislav Brabec <sbrabec@suse.cz>
Tested-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Tested-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Matthew Garrett [Wed, 9 Dec 2009 20:31:37 +0000 (12:31 -0800)]
serial: 8250_pnp: use wildcard for serial Wacom tablets
Wacom claims that the WACF namespace will always be devoted to serial
Wacom tablets. Remove the existing entries and add a wildcard to avoid
having to update the kernel every time they add a new device.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Tested-by: Ping Cheng <pingc@wacom.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Alan Cox [Mon, 4 Jan 2010 16:26:50 +0000 (16:26 +0000)]
nozomi: quick fix for the close/close bug
Nozomi goes wrong if you get the sequence
open
open
close
[stuff]
close
which turns out to occur on some ppp type setups.
This is a quick patch up for the problem. It's not really fixing Nozomi
which completely fails to implement tty open/close semantics and all the
other needed stuff. Doing it right is a rather more invasive patch set and
not one that will backport.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Atsushi Nemoto [Sun, 10 Jan 2010 14:29:16 +0000 (23:29 +0900)]
compat_ioctl: Supress "unknown cmd" message on serial /dev/console
After the commit
fb07a5f8 ("compat_ioctl: remove all VT ioctl
handling"), I got this error message on 64-bit mips kernel with 32-bit
busybox userland:
ioctl32(init:1): Unknown cmd fd(0) cmd(
00005600){t:'V';sz:0} arg(
7fd76480) on /dev/console
The cmd 5600 is VT_OPENQRY. The busybox's init issues this ioctl to
know vt-console or serial-console. If the console was serial console,
VT ioctls are not handled by the serial driver.
And by quick search, I found some programs using VT_GETMODE to check
vt-console is available or not.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>