OSDN Git Service
Tomi Valkeinen [Mon, 22 Aug 2011 10:02:52 +0000 (13:02 +0300)]
OMAP: DSS2: HDMI: use default dividers
commit
8d88767a4377171752c22ac39bcb2b505eb751da upstream.
Use default regn and regm2 dividers in the hdmi driver if the board file
does not define them.
Cc: Mythri P K <mythripk@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andrew Lunn [Wed, 8 Feb 2012 14:52:07 +0000 (15:52 +0100)]
ARM: orion: Fix Orion5x GPIO regression from MPP cleanup
commit
b06540371063f0f07aafc1d1ac5e974da85c973c upstream.
Patchset "ARM: orion: Refactor the MPP code common in the orion
platform" broke at least Orion5x based platforms. These platforms have
pins configured as GPIO when the selector is not 0x0. However the
common code assumes the selector is always 0x0 for a GPIO lines. It
then ignores the GPIO bits in the MPP definitions, resulting in that
Orion5x machines cannot correctly configure there GPIO lines.
The Fix removes the assumption that the selector is always 0x0.
In order that none GPIO configurations are correctly blocked,
Kirkwood and mv78xx0 MPP definitions are corrected to only set the
GPIO bits for GPIO configurations.
This third version, which does not contain any whitespace changes,
and is rebased on v3.3-rc2.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Andrew Lunn [Wed, 8 Feb 2012 14:52:47 +0000 (15:52 +0100)]
ARM: orion: Fix USB phy for orion5x.
commit
72053353583230952c4b187e110e9da00dfc3afb upstream.
The patch "ARM: orion: Consolidate USB platform setup code.", commit
4fcd3f374a928081d391cd9a570afe3b2c692fdc broke USB on TS-7800 and
other orion5x boards, because the wrong type of PHY was being passed
to the EHCI driver in the platform data. Orion5x needs EHCI_PHY_ORION
and all the others want EHCI_PHY_NA.
Allow the mach- code to tell the generic plat-orion code which USB PHY
enum to place into the platform data.
Version 2: Rebase to v3.3-rc2.
Reported-by: Ambroz Bizjak <ambrop7@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Ambroz Bizjak <ambrop7@gmail.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kenneth Graunke [Wed, 8 Feb 2012 20:53:52 +0000 (12:53 -0800)]
drm/i915: gen7: Disable the RHWO optimization as it can cause GPU hangs.
commit
d71de14ddf423ccc9a2e3f7e37553c99ead20d7c upstream.
The BSpec Workarounds page states that bits 10 and 26 must be set to
avoid 3D ring hangs.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=41353
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=44610
Tested-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eugeni Dodonov [Wed, 8 Feb 2012 20:53:51 +0000 (12:53 -0800)]
drm/i915: gen7: work around a system hang on IVB
commit
db099c8f963fe656108e0a068274c5580a17f69b upstream.
This adds the workaround for WaCatErrorRejectionIssue which could result
in a system hang.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=41353
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=44610
Tested-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eugeni Dodonov [Wed, 8 Feb 2012 20:53:50 +0000 (12:53 -0800)]
drm/i915: gen7: Implement an L3 caching workaround.
commit
e4e0c058a19c41150d12ad2d3023b3cf09c5de67 upstream.
This adds two cache-related workarounds for Ivy Bridge which can lead to
3D ring hangs and corruptions.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=41353
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=44610
Tested-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eugeni Dodonov [Wed, 8 Feb 2012 20:53:49 +0000 (12:53 -0800)]
drm/i915: gen7: implement rczunit workaround
commit
eae66b50c760233fad526edf4a0d327be17a055d upstream.
This is yet another workaround related to clock gating which we need on
Ivy Bridge.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=41353
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=44610
Tested-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jan Beulich [Tue, 28 Feb 2012 10:41:37 +0000 (10:41 +0000)]
kprobes: adjust "fix a memory leak in function pre_handler_kretprobe()"
3.0.21's
603b63484725a6e88e4ae5da58716efd88154b1e directly used
the upstream patch, yet kprobes locking in 3.0.x uses spin_lock...()
rather than raw_spin_lock...().
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fabio Baltieri [Fri, 3 Feb 2012 23:37:14 +0000 (15:37 -0800)]
avr32: select generic atomic64_t support
commit
31e0017e6f6fb5cfdfaf932c1f98c9bef8d57688 upstream.
Enable use of the generic atomic64 implementation on AVR32 platforms.
Without this the kernel fails to build as the architecture does not
provide its version.
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Keng-Yu Lin [Thu, 1 Dec 2011 23:04:23 +0000 (00:04 +0100)]
ACPI / PM: Do not save/restore NVS on Asus K54C/K54HR
commit
5a50a7c32d630d6cdb13d69afabb0cc81b2f379c upstream.
The models do not resume correctly without acpi_sleep=nonvs.
Signed-off-by: Keng-Yu Lin <kengyu@canonical.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stanislaw Gruszka [Wed, 8 Feb 2012 19:02:03 +0000 (20:02 +0100)]
bsg: fix sysfs link remove warning
commit
37b40adf2d1b4a5e51323be73ccf8ddcf3f15dd3 upstream.
We create "bsg" link if q->kobj.sd is not NULL, so remove it only
when the same condition is true.
Fixes:
WARNING: at fs/sysfs/inode.c:323 sysfs_hash_and_remove+0x2b/0x77()
sysfs: can not remove 'bsg', no directory
Call Trace:
[<
c0429683>] warn_slowpath_common+0x6a/0x7f
[<
c0537a68>] ? sysfs_hash_and_remove+0x2b/0x77
[<
c042970b>] warn_slowpath_fmt+0x2b/0x2f
[<
c0537a68>] sysfs_hash_and_remove+0x2b/0x77
[<
c053969a>] sysfs_remove_link+0x20/0x23
[<
c05d88f1>] bsg_unregister_queue+0x40/0x6d
[<
c0692263>] __scsi_remove_device+0x31/0x9d
[<
c069149f>] scsi_forget_host+0x41/0x52
[<
c0689fa9>] scsi_remove_host+0x71/0xe0
[<
f7de5945>] quiesce_and_remove_host+0x51/0x83 [usb_storage]
[<
f7de5a1e>] usb_stor_disconnect+0x18/0x22 [usb_storage]
[<
c06c29de>] usb_unbind_interface+0x4e/0x109
[<
c067a80f>] __device_release_driver+0x6b/0xa6
[<
c067a861>] device_release_driver+0x17/0x22
[<
c067a46a>] bus_remove_device+0xd6/0xe6
[<
c06785e2>] device_del+0xf2/0x137
[<
c06c101f>] usb_disable_device+0x94/0x1a0
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Javier Martin [Thu, 23 Feb 2012 14:43:18 +0000 (15:43 +0100)]
ASoC: i.MX SSI: Fix DSP_A format.
commit
5ed80a75b248bfaf840ea6b38f941edcf6ee7dc7 upstream.
According to i.MX27 Reference Manual (p 1593) TXBIT0 bit selects
whether the most significant or the less significant part of the
data word written to the FIFO is transmitted.
As DSP_A is the same as DSP_B with a data offset of 1 bit, it
doesn't make any sense to remove TXBIT0 bit here.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mark Brown [Wed, 22 Feb 2012 15:52:56 +0000 (15:52 +0000)]
ASoC: dapm: Check for bias level when powering down
commit
7679e42ec833ed70aa34790a5f39dcb7e5bda4fe upstream.
Recent enhancements in the bias management means that we might not be
in standby when the CODEC is idle and can have active widgets without
being in full power mode but the shutdown functionality assumes these
things. Add checks for the bias level at each stage so that we don't
do transitions other than the ON->PREPARE->STANDBY->OFF ones that the
drivers are expecting.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Boaz Harrosh [Wed, 25 Jan 2012 19:42:58 +0000 (21:42 +0200)]
osd_uld: Bump MAX_OSD_DEVICES from 64 to 1,048,576
commit
41f8ad76362e7aefe3a03949c43e23102dae6e0b upstream.
It used to be that minors where 8 bit. But now they
are actually 20 bit. So the fix is simplicity itself.
I've tested with 300 devices and all user-mode utils
work just fine. I have also mechanically added 10,000
to the ida (so devices are /dev/osd10000, /dev/osd10001 ...)
and was able to mkfs an exofs filesystem and access osds
from user-mode.
All the open-osd user-mode code uses the same library
to access devices through their symbolic names in
/dev/osdX so I'd say it's pretty safe. (Well tested)
This patch is very important because some of the systems
that will be deploying the 3.2 pnfs-objects code are larger
than 64 OSDs and will stop to work properly when reaching
that number.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Phil Sutter [Mon, 27 Feb 2012 11:17:04 +0000 (12:17 +0100)]
crypto: mv_cesa - fix final callback not ignoring input data
commit
f8f54e190ddb4ed697036b60f5e2ae6dd45b801c upstream.
Broken by commit
6ef84509f3d439ed2d43ea40080643efec37f54f for users
passing a request with non-zero 'nbytes' field, like e.g. testmgr.
Signed-off-by: Phil Sutter <phil.sutter@viprinet.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Stern [Mon, 27 Feb 2012 16:23:45 +0000 (11:23 -0500)]
HID: usbhid: Add NOGET quirk for the AIREN Slim+ keyboard
commit
37891abc8464637964a26ae4b61d307fef831f80 upstream.
This patch (as1531) adds a NOGET quirk for the Slim+ keyboard marketed
by AIREN. This keyboard seems to have a lot of bugs; NOGET works
around only one of them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: okias <d.okias@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andrea Arcangeli [Mon, 5 Mar 2012 22:59:20 +0000 (14:59 -0800)]
mm: thp: fix BUG on mm->nr_ptes
commit
1c641e84719429bbfe62a95ed3545ee7fe24408f upstream.
Dave Jones reports a few Fedora users hitting the BUG_ON(mm->nr_ptes...)
in exit_mmap() recently.
Quoting Hugh's discovery and explanation of the SMP race condition:
"mm->nr_ptes had unusual locking: down_read mmap_sem plus
page_table_lock when incrementing, down_write mmap_sem (or mm_users
0) when decrementing; whereas THP is careful to increment and
decrement it under page_table_lock.
Now most of those paths in THP also hold mmap_sem for read or write
(with appropriate checks on mm_users), but two do not: when
split_huge_page() is called by hwpoison_user_mappings(), and when
called by add_to_swap().
It's conceivable that the latter case is responsible for the
exit_mmap() BUG_ON mm->nr_ptes that has been reported on Fedora."
The simplest way to fix it without having to alter the locking is to make
split_huge_page() a noop in nr_ptes terms, so by counting the preallocated
pagetables that exists for every mapped hugepage. It was an arbitrary
choice not to count them and either way is not wrong or right, because
they are not used but they're still allocated.
Reported-by: Dave Jones <davej@redhat.com>
Reported-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Acked-by: Hugh Dickins <hughd@google.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Felix Fietkau [Wed, 15 Feb 2012 18:31:20 +0000 (19:31 +0100)]
ath9k_hw: prevent writes to const data on AR9160
commit
9bbb8168ed3d8b946f9c1901a63a675012de88f2 upstream.
Duplicate the data for iniAddac early on, to avoid having to do redundant
memcpy calls later. While we're at it, make AR5416 < v2.2 use the same
codepath. Fixes a reported crash on x86.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Magnus Määttä <magnus.maatta@logica.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mohammed Shafi Shajakhan [Mon, 20 Feb 2012 04:35:31 +0000 (10:05 +0530)]
mac80211: zero initialize count field in ieee80211_tx_rate
commit
8617b093d0031837a7be9b32bc674580cfb5f6b5 upstream.
rate control algorithms concludes the rate as invalid
with rate[i].idx < -1 , while they do also check for rate[i].count is
non-zero. it would be safer to zero initialize the 'count' field.
recently we had a ath9k rate control crash where the ath9k rate control
in ath_tx_status assumed to check only for rate[i].count being non-zero
in one instance and ended up in using invalid rate index for
'connection monitoring NULL func frames' which eventually lead to the crash.
thanks to Pavel Roskin for fixing it and finding the root cause.
https://bugzilla.redhat.com/show_bug.cgi?id=768639
Cc: Pavel Roskin <proski@gnu.org>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jeff Layton [Thu, 23 Feb 2012 14:37:45 +0000 (09:37 -0500)]
cifs: fix dentry refcount leak when opening a FIFO on lookup
commit
5bccda0ebc7c0331b81ac47d39e4b920b198b2cd upstream.
The cifs code will attempt to open files on lookup under certain
circumstances. What happens though if we find that the file we opened
was actually a FIFO or other special file?
Currently, the open filehandle just ends up being leaked leading to
a dentry refcount mismatch and oops on umount. Fix this by having the
code close the filehandle on the server if it turns out not to be a
regular file. While we're at it, change this spaghetti if statement
into a switch too.
Reported-by: CAI Qian <caiqian@redhat.com>
Tested-by: CAI Qian <caiqian@redhat.com>
Reviewed-by: Shirish Pargaonkar <shirishpargaonkar@gmail.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
David Howells [Thu, 23 Feb 2012 13:51:00 +0000 (13:51 +0000)]
NOMMU: Don't need to clear vm_mm when deleting a VMA
commit
b94cfaf6685d691dc3fab023cf32f65e9b7be09c upstream.
Don't clear vm_mm in a deleted VMA as it's unnecessary and might
conceivably break the filesystem or driver VMA close routine.
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Anton Vorontsov [Fri, 24 Feb 2012 01:14:46 +0000 (05:14 +0400)]
mm: memcg: Correct unregistring of events attached to the same eventfd
commit
371528caec553785c37f73fa3926ea0de84f986f upstream.
There is an issue when memcg unregisters events that were attached to
the same eventfd:
- On the first call mem_cgroup_usage_unregister_event() removes all
events attached to a given eventfd, and if there were no events left,
thresholds->primary would become NULL;
- Since there were several events registered, cgroups core will call
mem_cgroup_usage_unregister_event() again, but now kernel will oops,
as the function doesn't expect that threshold->primary may be NULL.
That's a good question whether mem_cgroup_usage_unregister_event()
should actually remove all events in one go, but nowadays it can't
do any better as cftype->unregister_event callback doesn't pass
any private event-associated cookie. So, let's fix the issue by
simply checking for threshold->primary.
FWIW, w/o the patch the following oops may be observed:
BUG: unable to handle kernel NULL pointer dereference at
0000000000000004
IP: [<
ffffffff810be32c>] mem_cgroup_usage_unregister_event+0x9c/0x1f0
Pid: 574, comm: kworker/0:2 Not tainted 3.3.0-rc4+ #9 Bochs Bochs
RIP: 0010:[<
ffffffff810be32c>] [<
ffffffff810be32c>] mem_cgroup_usage_unregister_event+0x9c/0x1f0
RSP: 0018:
ffff88001d0b9d60 EFLAGS:
00010246
Process kworker/0:2 (pid: 574, threadinfo
ffff88001d0b8000, task
ffff88001de91cc0)
Call Trace:
[<
ffffffff8107092b>] cgroup_event_remove+0x2b/0x60
[<
ffffffff8103db94>] process_one_work+0x174/0x450
[<
ffffffff8103e413>] worker_thread+0x123/0x2d0
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sascha Hauer [Fri, 17 Feb 2012 10:51:49 +0000 (11:51 +0100)]
mmc: sdhci-esdhc-imx: fix for mmc cards on i.MX5
commit
5b6b0ad6e572b32a641116aaa5f897ffebe31e44 upstream.
On i.MX53 we have to write a special SDHCI_CMD_ABORTCMD to the
SDHCI_TRANSFER_MODE register during a MMC_STOP_TRANSMISSION
command. This works for SD cards. However, with MMC cards
the MMC_SET_BLOCK_COUNT command is used instead, but this
needs the same handling. Fix MMC cards by testing for the
MMC_SET_BLOCK_COUNT command aswell. Tested on a custom i.MX53
board with a Transcend MMC+ card and eMMC.
The kernel started used MMC_SET_BLOCK_COUNT in 3.0, so this
is a regression for these boards introduced in 3.0; it should
go to 3.0/3.1/3.2-stable.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andrew Morton [Mon, 5 Mar 2012 22:59:19 +0000 (14:59 -0800)]
alpha: fix 32/64-bit bug in futex support
commit
62aca403657fe30e5235c5331e9871e676d9ea0a upstream.
Michael Cree said:
: : I have noticed some user space problems (pulseaudio crashes in pthread
: : code, glibc/nptl test suite failures, java compiler freezes on SMP alpha
: : systems) that arise when using a 2.6.39 or later kernel on Alpha.
: : Bisecting between 2.6.38 and 2.6.39 (using glibc/nptl test suite as
: : criterion for good/bad kernel) eventually leads to:
: :
: :
8d7718aa082aaf30a0b4989e1f04858952f941bc is the first bad commit
: : commit
8d7718aa082aaf30a0b4989e1f04858952f941bc
: : Author: Michel Lespinasse <walken@google.com>
: : Date: Thu Mar 10 18:50:58 2011 -0800
: :
: : futex: Sanitize futex ops argument types
: :
: : Change futex_atomic_op_inuser and futex_atomic_cmpxchg_inatomic
: : prototypes to use u32 types for the futex as this is the data type the
: : futex core code uses all over the place.
: :
: : Looking at the commit I see there is a change of the uaddr argument in
: : the Alpha architecture specific code for futexes from int to u32, but I
: : don't see why this should cause a problem.
Richard Henderson said:
: futex_atomic_cmpxchg_inatomic(u32 *uval, u32 __user *uaddr,
: u32 oldval, u32 newval)
: ...
: : "r"(uaddr), "r"((long)oldval), "r"(newval)
:
:
: There is no 32-bit compare instruction. These are implemented by
: consistently extending the values to a 64-bit type. Since the
: load instruction sign-extends, we want to sign-extend the other
: quantity as well (despite the fact it's logically unsigned).
:
: So:
:
: - : "r"(uaddr), "r"((long)oldval), "r"(newval)
: + : "r"(uaddr), "r"((long)(int)oldval), "r"(newval)
:
: should do the trick.
Michael said:
: This fixes the glibc test suite failures and the pulseaudio related
: crashes, but it does not fix the java compiiler lockups that I was (and
: are still) observing. That is some other problem.
Reported-by: Michael Cree <mcree@orcon.net.nz>
Tested-by: Michael Cree <mcree@orcon.net.nz>
Acked-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Michel Lespinasse <walken@google.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Reviewed-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Scott Talbert [Tue, 21 Feb 2012 13:06:00 +0000 (13:06 +0000)]
Move Logitech Harmony 900 from cdc_ether to zaurus
commit
ee932bf9acb2e2c6a309e808000f24856330e3f9 upstream.
In the current kernel implementation, the Logitech Harmony 900 remote
control is matched to the cdc_ether driver through the generic
USB_CDC_SUBCLASS_MDLM entry. However, this device appears to be of the
pseudo-MDLM (Belcarra) type, rather than the standard one. This patch
blacklists the Harmony 900 from the cdc_ether driver and whitelists it for
the pseudo-MDLM driver in zaurus.
Signed-off-by: Scott Talbert <talbert@techie.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Gusakov Andrey [Fri, 2 Mar 2012 22:32:36 +0000 (07:32 +0900)]
ARM: S3C24XX: DMA resume regression fix
commit
e39d40c65dfd8390b50c03482ae9e289b8a8f351 upstream.
s3c2410_dma_suspend suspends channels from 0 to dma_channels.
s3c2410_dma_resume resumes channels in reverse order. So
pointer should be decremented instead of being incremented.
Signed-off-by: Gusakov Andrey <dron0gus@gmail.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Gleixner [Tue, 6 Mar 2012 22:18:54 +0000 (23:18 +0100)]
genirq: Clear action->thread_mask if IRQ_ONESHOT is not set
commit
52abb700e16a9aa4cbc03f3d7f80206cbbc80680 upstream.
Xommit
ac5637611(genirq: Unmask oneshot irqs when thread was not woken)
fails to unmask when a !IRQ_ONESHOT threaded handler is handled by
handle_level_irq.
This happens because thread_mask is or'ed unconditionally in
irq_wake_thread(), but for !IRQ_ONESHOT interrupts never cleared. So
the check for !desc->thread_active fails and keeps the interrupt
disabled.
Keep the thread_mask zero for !IRQ_ONESHOT interrupts.
Document the thread_mask magic while at it.
Reported-and-tested-by: Sven Joachim <svenjoac@gmx.de>
Reported-and-tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jean Delvare [Sat, 18 Feb 2012 16:54:23 +0000 (17:54 +0100)]
mfd: Fix ACPI conflict check
commit
81b5482c32769abb6dfb979560dab2f952ba86fa upstream.
The code is currently always checking the first resource of every
device only (several times.) This has been broken since the ACPI check
was added in February 2010 in commit
91fedede0338eb6203cdd618d8ece873fdb7c22c.
Fix the check to run on each resource individually, once.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
H. Peter Anvin [Fri, 2 Mar 2012 18:43:49 +0000 (10:43 -0800)]
regset: Return -EFAULT, not -EIO, on host-side memory fault
commit
5189fa19a4b2b4c3bec37c3a019d446148827717 upstream.
There is only one error code to return for a bad user-space buffer
pointer passed to a system call in the same address space as the
system call is executed, and that is EFAULT. Furthermore, the
low-level access routines, which catch most of the faults, return
EFAULT already.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Roland McGrath <roland@hack.frob.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
H. Peter Anvin [Fri, 2 Mar 2012 18:43:48 +0000 (10:43 -0800)]
regset: Prevent null pointer reference on readonly regsets
commit
c8e252586f8d5de906385d8cf6385fee289a825e upstream.
The regset common infrastructure assumed that regsets would always
have .get and .set methods, but not necessarily .active methods.
Unfortunately people have since written regsets without .set methods.
Rather than putting in stub functions everywhere, handle regsets with
null .get or .set methods explicitly.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Roland McGrath <roland@hack.frob.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Takashi Iwai [Wed, 29 Feb 2012 08:41:17 +0000 (09:41 +0100)]
ALSA: hda - Always set HP pin in unsol handler for STAC/IDT codecs
commit
7bff172a352a2fbe9856bba517d71a2072aab041 upstream.
A bug report with an old Sony laptop showed that we can't rely on BIOS
setting the pins of headphones but the driver should set always by
itself.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Takashi Iwai [Mon, 27 Feb 2012 14:00:58 +0000 (15:00 +0100)]
ALSA: hda - Add a fake mute feature
commit
3868137ea41866773e75d9ac4b9988dcc361ff1d upstream.
Some codecs don't supply the mute amp-capabilities although the lowest
volume gives the mute. It'd be handy if the parser provides the mute
mixers in such a case.
This patch adds an extension amp-cap bit (which is used only in the
driver) to represent the min volume = mute state. Also modified the
amp cache code to support the fake mute feature when this bit is set
but the real mute bit is unset.
In addition, conexant cx5051 parser uses this new feature to implement
the missing mute controls.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=42825
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
David Howells [Fri, 24 Feb 2012 17:01:27 +0000 (18:01 +0100)]
S390: KEYS: Enable the compat keyctl wrapper on s390x
commit
1d057720609ed052a6371fe1d53300e5e6328e94 upstream.
Enable the compat keyctl wrapper on s390x so that 32-bit s390 userspace can
call the keyctl() syscall.
There's an s390x assembly wrapper that truncates all the register values to
32-bits and this then calls compat_sys_keyctl() - but the latter only exists if
CONFIG_KEYS_COMPAT is enabled, and the s390 Kconfig doesn't enable it.
Without this patch, 32-bit calls to the keyctl() syscall are given an ENOSYS
error:
[root@devel4 ~]# keyctl show
Session Keyring
-3: key inaccessible (Function not implemented)
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: dan@danny.cz
Cc: Carsten Otte <cotte@de.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: linux-s390@vger.kernel.org
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jett.Zhou [Thu, 23 Feb 2012 11:52:08 +0000 (19:52 +0800)]
regulator: fix the ldo configure according to 88pm860x spec
commit
3380643b0eaa7ecf99c4f095bdfcb6e5df471616 upstream.
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wolfram Sang [Fri, 13 Jan 2012 11:14:26 +0000 (12:14 +0100)]
i2c: mxs: only flag completion when queue is completely done
commit
844990daa2e69a4258049ba9c2bae1180657dac3 upstream.
The hardware generates an interrupt for every completed command in the
queue while the code assumed that it will only generate one interrupt
when the queue is empty. So, explicitly check if the queue is really
empty. This patch fixed problems which occurred due to high traffic on
the bus. While we are here, move the completion-initialization after the
parameter error checking.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Maxim Uvarov [Mon, 16 Jan 2012 04:02:50 +0000 (20:02 -0800)]
watchdog: hpwdt: clean up set_memory_x call for 32 bit
commit
97d2a10d5804d585ab0b58efbd710948401b886a upstream.
1. address has to be page aligned.
2. set_memory_x uses page size argument, not size.
Bug causes with following commit:
commit
da28179b4e90dda56912ee825c7eaa62fc103797
Author: Mingarelli, Thomas <Thomas.Mingarelli@hp.com>
Date: Mon Nov 7 10:59:00 2011 +0100
watchdog: hpwdt: Changes to handle NX secure bit in 32bit path
commit
e67d668e147c3b4fec638c9e0ace04319f5ceccd upstream.
This patch makes use of the set_memory_x() kernel API in order
to make necessary BIOS calls to source NMIs.
Signed-off-by: Maxim Uvarov <maxim.uvarov@oracle.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Roland Stigge [Mon, 27 Feb 2012 16:28:02 +0000 (17:28 +0100)]
ARM: LPC32xx: Fix irq on GPI_28
commit
f6737055c1c432a9628a9a731f9881ad8e0a9eee upstream.
The GPI_28 IRQ was not registered properly. The registration of
IRQ_LPC32XX_GPI_28 was added and the (wrong) IRQ_LPC32XX_GPI_11 at
LPC32XX_SIC1_IRQ(4) was replaced by IRQ_LPC32XX_GPI_28 (see manual of
LPC32xx / interrupt controller).
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Roland Stigge [Mon, 27 Feb 2012 16:28:02 +0000 (17:28 +0100)]
ARM: LPC32xx: Fix interrupt controller init
commit
35dd0a75d4a382e7f769dd0277732e7aa5235718 upstream.
This patch fixes the initialization of the interrupt controller of the LPC32xx
by correctly setting up SIC1 and SIC2 instead of (wrongly) using the same value
as for the Main Interrupt Controller (MIC).
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Roland Stigge [Mon, 27 Feb 2012 16:28:02 +0000 (17:28 +0100)]
ARM: LPC32xx: irq.c: Clear latched event
commit
94ed7830cba4dce57b18a2926b5d826bfd184bd6 upstream.
This patch fixes the wakeup disable function by clearing latched events.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Roland Stigge [Mon, 27 Feb 2012 16:28:03 +0000 (17:28 +0100)]
ARM: LPC32xx: serial.c: Fixed loop limit
commit
ff424aa4c89d19082e8ae5a3351006bc8a4cd91b upstream.
This patch fixes a wrong loop limit on UART init.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Roland Stigge [Mon, 27 Feb 2012 16:28:02 +0000 (17:28 +0100)]
ARM: LPC32xx: serial.c: HW bug workaround
commit
2707208ee8a80dbbd5426f5aa1a934f766825bb5 upstream.
This patch fixes a HW bug by flushing RX FIFOs of the UARTs on init. It was
ported from NXP's git.lpclinux.com tree.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alban Browaeys [Fri, 24 Feb 2012 17:12:45 +0000 (17:12 +0000)]
drm/i915: Prevent a machine hang by checking crtc->active before loading lut
commit
aed3f09db39596e539f90b11a5016aea4d8442e1 upstream.
Before loading the lut (gamma), check the active state of intel_crtc,
otherwise at least on gen2 hang ensue.
This is reproducible in Xorg via:
xset dpms force off
then
xgamma -rgamma 2.0 # freeze.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=44505
Signed-off-by: Alban Browaeys <prahal@yahoo.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Heiko Carstens [Mon, 27 Feb 2012 09:01:52 +0000 (10:01 +0100)]
compat: fix compile breakage on s390
commit
048cd4e51d24ebf7f3552226d03c769d6ad91658 upstream.
The new is_compat_task() define for the !COMPAT case in
include/linux/compat.h conflicts with a similar define in
arch/s390/include/asm/compat.h.
This is the minimal patch which fixes the build issues.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Sun, 26 Feb 2012 17:44:55 +0000 (09:44 -0800)]
Fix autofs compile without CONFIG_COMPAT
commit
3c761ea05a8900a907f32b628611873f6bef24b2 upstream.
The autofs compat handling fix caused a compile failure when
CONFIG_COMPAT isn't defined.
Instead of adding random #ifdef'fery in autofs, let's just make the
compat helpers earlier to use: without CONFIG_COMPAT, is_compat_task()
just hardcodes to zero.
We could probably do something similar for a number of other cases where
we have #ifdef's in code, but this is the low-hanging fruit.
Reported-and-tested-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ian Kent [Wed, 22 Feb 2012 12:45:44 +0000 (20:45 +0800)]
autofs: work around unhappy compat problem on x86-64
commit
a32744d4abae24572eff7269bc17895c41bd0085 upstream.
When the autofs protocol version 5 packet type was added in commit
5c0a32fc2cd0 ("autofs4: add new packet type for v5 communications"), it
obvously tried quite hard to be word-size agnostic, and uses explicitly
sized fields that are all correctly aligned.
However, with the final "char name[NAME_MAX+1]" array at the end, the
actual size of the structure ends up being not very well defined:
because the struct isn't marked 'packed', doing a "sizeof()" on it will
align the size of the struct up to the biggest alignment of the members
it has.
And despite all the members being the same, the alignment of them is
different: a "__u64" has 4-byte alignment on x86-32, but native 8-byte
alignment on x86-64. And while 'NAME_MAX+1' ends up being a nice round
number (256), the name[] array starts out a 4-byte aligned.
End result: the "packed" size of the structure is 300 bytes: 4-byte, but
not 8-byte aligned.
As a result, despite all the fields being in the same place on all
architectures, sizeof() will round up that size to 304 bytes on
architectures that have 8-byte alignment for u64.
Note that this is *not* a problem for 32-bit compat mode on POWER, since
there __u64 is 8-byte aligned even in 32-bit mode. But on x86, 32-bit
and 64-bit alignment is different for 64-bit entities, and as a result
the structure that has exactly the same layout has different sizes.
So on x86-64, but no other architecture, we will just subtract 4 from
the size of the structure when running in a compat task. That way we
will write the properly sized packet that user mode expects.
Not pretty. Sadly, this very subtle, and unnecessary, size difference
has been encoded in user space that wants to read packets of *exactly*
the right size, and will refuse to touch anything else.
Reported-and-tested-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Ian Kent <raven@themaw.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Thu, 1 Mar 2012 00:35:02 +0000 (16:35 -0800)]
Linux 3.0.23
Dan Carpenter [Mon, 6 Feb 2012 09:20:45 +0000 (10:20 +0100)]
cdrom: use copy_to_user() without the underscores
commit
822bfa51ce44f2c63c300fdb76dc99c4d5a5ca9f upstream.
"nframes" comes from the user and "nframes * CD_FRAMESIZE_RAW" can wrap
on 32 bit systems. That would have been ok if we used the same wrapped
value for the copy, but we use a shifted value. We should just use the
checked version of copy_to_user() because it's not going to make a
difference to the speed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jason Baron [Fri, 13 Jan 2012 01:17:43 +0000 (17:17 -0800)]
epoll: limit paths
commit
28d82dc1c4edbc352129f97f4ca22624d1fe61de upstream.
The current epoll code can be tickled to run basically indefinitely in
both loop detection path check (on ep_insert()), and in the wakeup paths.
The programs that tickle this behavior set up deeply linked networks of
epoll file descriptors that cause the epoll algorithms to traverse them
indefinitely. A couple of these sample programs have been previously
posted in this thread: https://lkml.org/lkml/2011/2/25/297.
To fix the loop detection path check algorithms, I simply keep track of
the epoll nodes that have been already visited. Thus, the loop detection
becomes proportional to the number of epoll file descriptor and links.
This dramatically decreases the run-time of the loop check algorithm. In
one diabolical case I tried it reduced the run-time from 15 mintues (all
in kernel time) to .3 seconds.
Fixing the wakeup paths could be done at wakeup time in a similar manner
by keeping track of nodes that have already been visited, but the
complexity is harder, since there can be multiple wakeups on different
cpus...Thus, I've opted to limit the number of possible wakeup paths when
the paths are created.
This is accomplished, by noting that the end file descriptor points that
are found during the loop detection pass (from the newly added link), are
actually the sources for wakeup events. I keep a list of these file
descriptors and limit the number and length of these paths that emanate
from these 'source file descriptors'. In the current implemetation I
allow 1000 paths of length 1, 500 of length 2, 100 of length 3, 50 of
length 4 and 10 of length 5. Note that it is sufficient to check the
'source file descriptors' reachable from the newly added link, since no
other 'source file descriptors' will have newly added links. This allows
us to check only the wakeup paths that may have gotten too long, and not
re-check all possible wakeup paths on the system.
In terms of the path limit selection, I think its first worth noting that
the most common case for epoll, is probably the model where you have 1
epoll file descriptor that is monitoring n number of 'source file
descriptors'. In this case, each 'source file descriptor' has a 1 path of
length 1. Thus, I believe that the limits I'm proposing are quite
reasonable and in fact may be too generous. Thus, I'm hoping that the
proposed limits will not prevent any workloads that currently work to
fail.
In terms of locking, I have extended the use of the 'epmutex' to all
epoll_ctl add and remove operations. Currently its only used in a subset
of the add paths. I need to hold the epmutex, so that we can correctly
traverse a coherent graph, to check the number of paths. I believe that
this additional locking is probably ok, since its in the setup/teardown
paths, and doesn't affect the running paths, but it certainly is going to
add some extra overhead. Also, worth noting is that the epmuex was
recently added to the ep_ctl add operations in the initial path loop
detection code using the argument that it was not on a critical path.
Another thing to note here, is the length of epoll chains that is allowed.
Currently, eventpoll.c defines:
/* Maximum number of nesting allowed inside epoll sets */
#define EP_MAX_NESTS 4
This basically means that I am limited to a graph depth of 5 (EP_MAX_NESTS
+ 1). However, this limit is currently only enforced during the loop
check detection code, and only when the epoll file descriptors are added
in a certain order. Thus, this limit is currently easily bypassed. The
newly added check for wakeup paths, stricly limits the wakeup paths to a
length of 5, regardless of the order in which ep's are linked together.
Thus, a side-effect of the new code is a more consistent enforcement of
the graph depth.
Thus far, I've tested this, using the sample programs previously
mentioned, which now either return quickly or return -EINVAL. I've also
testing using the piptest.c epoll tester, which showed no difference in
performance. I've also created a number of different epoll networks and
tested that they behave as expectded.
I believe this solves the original diabolical test cases, while still
preserving the sane epoll nesting.
Signed-off-by: Jason Baron <jbaron@redhat.com>
Cc: Nelson Elhage <nelhage@ksplice.com>
Cc: Davide Libenzi <davidel@xmailserver.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Oleg Nesterov [Fri, 24 Feb 2012 19:07:29 +0000 (20:07 +0100)]
epoll: ep_unregister_pollwait() can use the freed pwq->whead
commit
971316f0503a5c50633d07b83b6db2f15a3a5b00 upstream.
signalfd_cleanup() ensures that ->signalfd_wqh is not used, but
this is not enough. eppoll_entry->whead still points to the memory
we are going to free, ep_unregister_pollwait()->remove_wait_queue()
is obviously unsafe.
Change ep_poll_callback(POLLFREE) to set eppoll_entry->whead = NULL,
change ep_unregister_pollwait() to check pwq->whead != NULL under
rcu_read_lock() before remove_wait_queue(). We add the new helper,
ep_remove_wait_queue(), for this.
This works because sighand_cachep is SLAB_DESTROY_BY_RCU and because
->signalfd_wqh is initialized in sighand_ctor(), not in copy_sighand.
ep_unregister_pollwait()->remove_wait_queue() can play with already
freed and potentially reused ->sighand, but this is fine. This memory
must have the valid ->signalfd_wqh until rcu_read_unlock().
Reported-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Oleg Nesterov [Fri, 24 Feb 2012 19:07:11 +0000 (20:07 +0100)]
epoll: introduce POLLFREE to flush ->signalfd_wqh before kfree()
commit
d80e731ecab420ddcb79ee9d0ac427acbc187b4b upstream.
This patch is intentionally incomplete to simplify the review.
It ignores ep_unregister_pollwait() which plays with the same wqh.
See the next change.
epoll assumes that the EPOLL_CTL_ADD'ed file controls everything
f_op->poll() needs. In particular it assumes that the wait queue
can't go away until eventpoll_release(). This is not true in case
of signalfd, the task which does EPOLL_CTL_ADD uses its ->sighand
which is not connected to the file.
This patch adds the special event, POLLFREE, currently only for
epoll. It expects that init_poll_funcptr()'ed hook should do the
necessary cleanup. Perhaps it should be defined as EPOLLFREE in
eventpoll.
__cleanup_sighand() is changed to do wake_up_poll(POLLFREE) if
->signalfd_wqh is not empty, we add the new signalfd_cleanup()
helper.
ep_poll_callback(POLLFREE) simply does list_del_init(task_list).
This make this poll entry inconsistent, but we don't care. If you
share epoll fd which contains our sigfd with another process you
should blame yourself. signalfd is "really special". I simply do
not know how we can define the "right" semantics if it used with
epoll.
The main problem is, epoll calls signalfd_poll() once to establish
the connection with the wait queue, after that signalfd_poll(NULL)
returns the different/inconsistent results depending on who does
EPOLL_CTL_MOD/signalfd_read/etc. IOW: apart from sigmask, signalfd
has nothing to do with the file, it works with the current thread.
In short: this patch is the hack which tries to fix the symptoms.
It also assumes that nobody can take tasklist_lock under epoll
locks, this seems to be true.
Note:
- we do not have wake_up_all_poll() but wake_up_poll()
is fine, poll/epoll doesn't use WQ_FLAG_EXCLUSIVE.
- signalfd_cleanup() uses POLLHUP along with POLLFREE,
we need a couple of simple changes in eventpoll.c to
make sure it can't be "lost".
Reported-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nikolaus Schulz [Wed, 22 Feb 2012 22:18:44 +0000 (23:18 +0100)]
hwmon: (f75375s) Fix register write order when setting fans to full speed
commit
c1c1a3d012fe5e82a9a025fb4b5a4f8ee67a53f6 upstream.
By hwmon sysfs interface convention, setting pwm_enable to zero sets a fan
to full speed. In the f75375s driver, this need be done by enabling
manual fan control, plus duty mode for the
F875387 chip, and then setting
the maximum duty cycle. Fix a bug where the two necessary register writes
were swapped, effectively discarding the setting to full-speed.
Signed-off-by: Nikolaus Schulz <mail@microschulz.de>
Cc: Riku Voipio <riku.voipio@iki.fi>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Janne Grunau [Thu, 2 Feb 2012 16:35:21 +0000 (13:35 -0300)]
hdpvr: fix race conditon during start of streaming
commit
afa159538af61f1a65d48927f4e949fe514fb4fc upstream.
status has to be set to STREAMING before the streaming worker is
queued. hdpvr_transmit_buffers() will exit immediately otherwise.
Reported-by: Joerg Desch <vvd.joede@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ben Hutchings [Wed, 15 Feb 2012 14:17:29 +0000 (14:17 +0000)]
builddeb: Don't create files in /tmp with predictable names
commit
6c635224602d760c1208ada337562f40d8ae93a5 upstream.
The current use of /tmp for file lists is insecure. Put them under
$objtree/debian instead.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: maximilian attems <max@stro.at>
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Christian Riesch [Thu, 23 Feb 2012 01:14:17 +0000 (01:14 +0000)]
davinci_emac: Do not free all rx dma descriptors during init
commit
5d69703263d588dbb03f4e57091afd8942d96e6d upstream.
This patch fixes a regression that was introduced by
commit
0a5f38467765ee15478db90d81e40c269c8dda20
davinci_emac: Add Carrier Link OK check in Davinci RX Handler
Said commit adds a check whether the carrier link is ok. If the link is
not ok, the skb is freed and no new dma descriptor added to the rx dma
channel. This causes trouble during initialization when the carrier
status has not yet been updated. If a lot of packets are received while
netif_carrier_ok returns false, all dma descriptors are freed and the
rx dma transfer is stopped.
The bug occurs when the board is connected to a network with lots of
traffic and the ifconfig down/up is done, e.g., when reconfiguring
the interface with DHCP.
The bug can be reproduced by flood pinging the davinci board while doing
ifconfig eth0 down
ifconfig eth0 up
on the board.
After that, the rx path stops working and the overrun value reported
by ifconfig is counting up.
This patch reverts commit
0a5f38467765ee15478db90d81e40c269c8dda20
and instead issues warnings only if cpdma_chan_submit returns -ENOMEM.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: <stable@vger.kernel.org>
Cc: Cyril Chemparathy <cyril@ti.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Guo-Fu Tseng [Wed, 22 Feb 2012 08:58:10 +0000 (08:58 +0000)]
jme: Fix FIFO flush issue
commit
ba9adbe67e288823ac1deb7f11576ab5653f833e upstream.
Set the RX FIFO flush watermark lower.
According to Federico and JMicron's reply,
setting it to 16QW would be stable on most platforms.
Otherwise, user might experience packet drop issue.
Reported-by: Federico Quagliata <federico@quagliata.org>
Fixed-by: Federico Quagliata <federico@quagliata.org>
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simon Horman [Fri, 27 Jan 2012 01:45:27 +0000 (10:45 +0900)]
ipvs: fix matching of fwmark templates during scheduling
commit
e0aac52e17a3db68fe2ceae281780a70fc69957f upstream.
Commit
f11017ec2d1859c661f4e2b12c4a8d250e1f47cf (2.6.37)
moved the fwmark variable in subcontext that is invalidated before
reaching the ip_vs_ct_in_get call. As vaddr is provided as pointer
in the param structure make sure the fwmark variable is in
same context. As the fwmark templates can not be matched,
more and more template connections are created and the
controlled connections can not go to single real server.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Stern [Fri, 17 Feb 2012 21:25:08 +0000 (16:25 -0500)]
scsi_pm: Fix bug in the SCSI power management handler
commit
fea6d607e154cf96ab22254ccb48addfd43d4cb5 upstream.
This patch (as1520) fixes a bug in the SCSI layer's power management
implementation.
LUN scanning can be carried out asynchronously in do_scan_async(), and
sd uses an asynchronous thread for the time-consuming parts of disk
probing in sd_probe_async(). Currently nothing coordinates these
async threads with system sleep transitions; they can and do attempt
to continue scanning/probing SCSI devices even after the host adapter
has been suspended. As one might expect, the outcome is not ideal.
This is what the "prepare" stage of system suspend was created for.
After the prepare callback has been called for a host, target, or
device, drivers are not allowed to register any children underneath
them. Currently the SCSI prepare callback is not implemented; this
patch rectifies that omission.
For SCSI hosts, the prepare routine calls scsi_complete_async_scans()
to wait until async scanning is finished. It might be slightly more
efficient to wait only until the host in question has been scanned,
but there's currently no way to do that. Besides, during a sleep
transition we will ultimately have to wait until all the host scanning
has finished anyway.
For SCSI devices, the prepare routine calls async_synchronize_full()
to wait until sd probing is finished. The routine does nothing for
SCSI targets, because asynchronous target scanning is done only as
part of host scanning.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Huajun Li [Sun, 12 Feb 2012 11:59:14 +0000 (19:59 +0800)]
scsi_scan: Fix 'Poison overwritten' warning caused by using freed 'shost'
commit
267a6ad4aefaafbde607804c60945bcf97f91c1b upstream.
In do_scan_async(), calling scsi_autopm_put_host(shost) may reference
freed shost, and cause Posison overwitten warning.
Yes, this case can happen, for example, an USB is disconnected just
when do_scan_async() thread starts to run, then scsi_host_put() called
in scsi_finish_async_scan() will lead to shost be freed(because the
refcount of shost->shost_gendev decreases to 1 after USB disconnects),
at this point, if references shost again, system will show following
warning msg.
To make scsi_autopm_put_host(shost) always reference a valid shost,
put it just before scsi_host_put() in function
scsi_finish_async_scan().
[ 299.281565] =============================================================================
[ 299.281634] BUG kmalloc-4096 (Tainted: G I ): Poison overwritten
[ 299.281682] -----------------------------------------------------------------------------
[ 299.281684]
[ 299.281752] INFO: 0xffff880056c305d0-0xffff880056c305d0. First byte
0x6a instead of 0x6b
[ 299.281816] INFO: Allocated in scsi_host_alloc+0x4a/0x490 age=1688
cpu=1 pid=2004
[ 299.281870] __slab_alloc+0x617/0x6c1
[ 299.281901] __kmalloc+0x28c/0x2e0
[ 299.281931] scsi_host_alloc+0x4a/0x490
[ 299.281966] usb_stor_probe1+0x5b/0xc40 [usb_storage]
[ 299.282010] storage_probe+0xa4/0xe0 [usb_storage]
[ 299.282062] usb_probe_interface+0x172/0x330 [usbcore]
[ 299.282105] driver_probe_device+0x257/0x3b0
[ 299.282138] __driver_attach+0x103/0x110
[ 299.282171] bus_for_each_dev+0x8e/0xe0
[ 299.282201] driver_attach+0x26/0x30
[ 299.282230] bus_add_driver+0x1c4/0x430
[ 299.282260] driver_register+0xb6/0x230
[ 299.282298] usb_register_driver+0xe5/0x270 [usbcore]
[ 299.282337] 0xffffffffa04ab03d
[ 299.282364] do_one_initcall+0x47/0x230
[ 299.282396] sys_init_module+0xa0f/0x1fe0
[ 299.282429] INFO: Freed in scsi_host_dev_release+0x18a/0x1d0 age=85
cpu=0 pid=2008
[ 299.282482] __slab_free+0x3c/0x2a1
[ 299.282510] kfree+0x296/0x310
[ 299.282536] scsi_host_dev_release+0x18a/0x1d0
[ 299.282574] device_release+0x74/0x100
[ 299.282606] kobject_release+0xc7/0x2a0
[ 299.282637] kobject_put+0x54/0xa0
[ 299.282668] put_device+0x27/0x40
[ 299.282694] scsi_host_put+0x1d/0x30
[ 299.282723] do_scan_async+0x1fc/0x2b0
[ 299.282753] kthread+0xdf/0xf0
[ 299.282782] kernel_thread_helper+0x4/0x10
[ 299.282817] INFO: Slab 0xffffea00015b0c00 objects=7 used=7 fp=0x
(null) flags=0x100000000004080
[ 299.282882] INFO: Object 0xffff880056c30000 @offset=0 fp=0x (null)
[ 299.282884]
...
Signed-off-by: Huajun Li <huajun.li.lee@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Gleixner [Wed, 8 Feb 2012 10:57:52 +0000 (11:57 +0100)]
genirq: Handle pending irqs in irq_startup()
commit
b4bc724e82e80478cba5fe9825b62e71ddf78757 upstream.
An interrupt might be pending when irq_startup() is called, but the
startup code does not invoke the resend logic. In some cases this
prevents the device from issuing another interrupt which renders the
device non functional.
Call the resend function in irq_startup() to keep things going.
Reported-and-tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Gleixner [Tue, 7 Feb 2012 16:58:03 +0000 (17:58 +0100)]
genirq: Unmask oneshot irqs when thread was not woken
commit
ac5637611150281f398bb7a47e3fcb69a09e7803 upstream.
When the primary handler of an interrupt which is marked IRQ_ONESHOT
returns IRQ_HANDLED or IRQ_NONE, then the interrupt thread is not
woken and the unmask logic of the interrupt line is never
invoked. This keeps the interrupt masked forever.
This was not noticed as most IRQ_ONESHOT users wake the thread
unconditionally (usually because they cannot access the underlying
device from hard interrupt context). Though this behaviour was nowhere
documented and not necessarily intentional. Some drivers can avoid the
thread wakeup in certain cases and run into the situation where the
interrupt line s kept masked.
Handle it gracefully.
Reported-and-tested-by: Lothar Wassmann <lw@karo-electronics.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pavel Roskin [Sat, 11 Feb 2012 15:01:53 +0000 (10:01 -0500)]
ath9k: stop on rates with idx -1 in ath9k rate control's .tx_status
commit
2504a6423b9ab4c36df78227055995644de19edb upstream.
Rate control algorithms are supposed to stop processing when they
encounter a rate with the index -1. Checking for rate->count not being
zero is not enough.
Allowing a rate with negative index leads to memory corruption in
ath_debug_stat_rc().
One consequence of the bug is discussed at
https://bugzilla.redhat.com/show_bug.cgi?id=768639
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andreas Herrmann [Wed, 8 Feb 2012 19:52:29 +0000 (20:52 +0100)]
x86/amd: Fix L1i and L2 cache sharing information for AMD family 15h processors
commit
32c3233885eb10ac9cb9410f2f8cd64b8df2b2a1 upstream.
For L1 instruction cache and L2 cache the shared CPU information
is wrong. On current AMD family 15h CPUs those caches are shared
between both cores of a compute unit.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=42607
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Petkov Borislav <Borislav.Petkov@amd.com>
Cc: Dave Jones <davej@redhat.com>
Link: http://lkml.kernel.org/r/20120208195229.GA17523@alberich.amd.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sarah Sharp [Thu, 23 Feb 2012 21:20:13 +0000 (13:20 -0800)]
USB: Don't fail USB3 probe on missing legacy PCI IRQ.
commit
68d07f64b8a11a852d48d1b05b724c3e20c0d94b upstream
Intel has a PCI USB xhci host controller on a new platform. It doesn't
have a line IRQ definition in BIOS. The Linux driver refuses to
initialize this controller, but Windows works well because it only depends
on MSI.
Actually, Linux also can work for MSI. This patch avoids the line IRQ
checking for USB3 HCDs in usb core PCI probe. It allows the xHCI driver
to try to enable MSI or MSI-X first. It will fail the probe if MSI
enabling failed and there's no legacy PCI IRQ.
This patch should be backported to kernels as old as 2.6.32.
[Maintainer note: This patch is a backport of commit
68d07f64b8a11a852d48d1b05b724c3e20c0d94b "USB: Don't fail USB3 probe on
missing legacy PCI IRQ." to the 3.0 kernel. Note, the original patch
description was wrong. We should not back port this to kernels older
than 2.6.36, since that was the first kernel to support MSI and MSI-X
for xHCI hosts. These systems will just not work without MSI support,
so the probe should fail on kernels older than 2.6.36.]
Signed-off-by: Alex Shi <alex.shi@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Stern [Tue, 21 Feb 2012 18:16:32 +0000 (13:16 -0500)]
usb-storage: fix freezing of the scanning thread
commit
bb94a406682770a35305daaa241ccdb7cab399de upstream.
This patch (as1521b) fixes the interaction between usb-storage's
scanning thread and the freezer. The current implementation has a
race: If the device is unplugged shortly after being plugged in and
just as a system sleep begins, the scanning thread may get frozen
before the khubd task. Khubd won't be able to freeze until the
disconnect processing is complete, and the disconnect processing can't
proceed until the scanning thread finishes, so the sleep transition
will fail.
The implementation in the 3.2 kernel suffers from an additional
problem. There the scanning thread calls set_freezable_with_signal(),
and the signals sent by the freezer will mess up the thread's I/O
delays, which are all interruptible.
The solution to both problems is the same: Replace the kernel thread
used for scanning with a delayed-work routine on the system freezable
work queue. Freezable work queues have the nice property that you can
cancel a work item even while the work queue is frozen, and no signals
are needed.
The 3.2 version of this patch solves the problem in Bugzilla #42730.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Sat, 18 Feb 2012 20:56:35 +0000 (12:56 -0800)]
i387: re-introduce FPU state preloading at context switch time
commit
34ddc81a230b15c0e345b6b253049db731499f7e upstream.
After all the FPU state cleanups and finally finding the problem that
caused all our FPU save/restore problems, this re-introduces the
preloading of FPU state that was removed in commit
b3b0870ef3ff ("i387:
do not preload FPU state at task switch time").
However, instead of simply reverting the removal, this reimplements
preloading with several fixes, most notably
- properly abstracted as a true FPU state switch, rather than as
open-coded save and restore with various hacks.
In particular, implementing it as a proper FPU state switch allows us
to optimize the CR0.TS flag accesses: there is no reason to set the
TS bit only to then almost immediately clear it again. CR0 accesses
are quite slow and expensive, don't flip the bit back and forth for
no good reason.
- Make sure that the same model works for both x86-32 and x86-64, so
that there are no gratuitous differences between the two due to the
way they save and restore segment state differently due to
architectural differences that really don't matter to the FPU state.
- Avoid exposing the "preload" state to the context switch routines,
and in particular allow the concept of lazy state restore: if nothing
else has used the FPU in the meantime, and the process is still on
the same CPU, we can avoid restoring state from memory entirely, just
re-expose the state that is still in the FPU unit.
That optimized lazy restore isn't actually implemented here, but the
infrastructure is set up for it. Of course, older CPU's that use
'fnsave' to save the state cannot take advantage of this, since the
state saving also trashes the state.
In other words, there is now an actual _design_ to the FPU state saving,
rather than just random historical baggage. Hopefully it's easier to
follow as a result.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Sat, 18 Feb 2012 05:48:54 +0000 (21:48 -0800)]
i387: move TS_USEDFPU flag from thread_info to task_struct
commit
f94edacf998516ac9d849f7bc6949a703977a7f3 upstream.
This moves the bit that indicates whether a thread has ownership of the
FPU from the TS_USEDFPU bit in thread_info->status to a word of its own
(called 'has_fpu') in task_struct->thread.has_fpu.
This fixes two independent bugs at the same time:
- changing 'thread_info->status' from the scheduler causes nasty
problems for the other users of that variable, since it is defined to
be thread-synchronous (that's what the "TS_" part of the naming was
supposed to indicate).
So perfectly valid code could (and did) do
ti->status |= TS_RESTORE_SIGMASK;
and the compiler was free to do that as separate load, or and store
instructions. Which can cause problems with preemption, since a task
switch could happen in between, and change the TS_USEDFPU bit. The
change to TS_USEDFPU would be overwritten by the final store.
In practice, this seldom happened, though, because the 'status' field
was seldom used more than once, so gcc would generally tend to
generate code that used a read-modify-write instruction and thus
happened to avoid this problem - RMW instructions are naturally low
fat and preemption-safe.
- On x86-32, the current_thread_info() pointer would, during interrupts
and softirqs, point to a *copy* of the real thread_info, because
x86-32 uses %esp to calculate the thread_info address, and thus the
separate irq (and softirq) stacks would cause these kinds of odd
thread_info copy aliases.
This is normally not a problem, since interrupts aren't supposed to
look at thread information anyway (what thread is running at
interrupt time really isn't very well-defined), but it confused the
heck out of irq_fpu_usable() and the code that tried to squirrel
away the FPU state.
(It also caused untold confusion for us poor kernel developers).
It also turns out that using 'task_struct' is actually much more natural
for most of the call sites that care about the FPU state, since they
tend to work with the task struct for other reasons anyway (ie
scheduling). And the FPU data that we are going to save/restore is
found there too.
Thanks to Arjan Van De Ven <arjan@linux.intel.com> for pointing us to
the %esp issue.
Cc: Arjan van de Ven <arjan@linux.intel.com>
Reported-and-tested-by: Raphael Prevost <raphael@buro.asia>
Acked-and-tested-by: Suresh Siddha <suresh.b.siddha@intel.com>
Tested-by: Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Fri, 17 Feb 2012 03:11:15 +0000 (19:11 -0800)]
i387: move AMD K7/K8 fpu fxsave/fxrstor workaround from save to restore
commit
4903062b5485f0e2c286a23b44c9b59d9b017d53 upstream.
The AMD K7/K8 CPUs don't save/restore FDP/FIP/FOP unless an exception is
pending. In order to not leak FIP state from one process to another, we
need to do a floating point load after the fxsave of the old process,
and before the fxrstor of the new FPU state. That resets the state to
the (uninteresting) kernel load, rather than some potentially sensitive
user information.
We used to do this directly after the FPU state save, but that is
actually very inconvenient, since it
(a) corrupts what is potentially perfectly good FPU state that we might
want to lazy avoid restoring later and
(b) on x86-64 it resulted in a very annoying ordering constraint, where
"__unlazy_fpu()" in the task switch needs to be delayed until after
the DS segment has been reloaded just to get the new DS value.
Coupling it to the fxrstor instead of the fxsave automatically avoids
both of these issues, and also ensures that we only do it when actually
necessary (the FP state after a save may never actually get used). It's
simply a much more natural place for the leaked state cleanup.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Thu, 16 Feb 2012 23:45:23 +0000 (15:45 -0800)]
i387: do not preload FPU state at task switch time
commit
b3b0870ef3ffed72b92415423da864f440f57ad6 upstream.
Yes, taking the trap to re-load the FPU/MMX state is expensive, but so
is spending several days looking for a bug in the state save/restore
code. And the preload code has some rather subtle interactions with
both paravirtualization support and segment state restore, so it's not
nearly as simple as it should be.
Also, now that we no longer necessarily depend on a single bit (ie
TS_USEDFPU) for keeping track of the state of the FPU, we migth be able
to do better. If we are really switching between two processes that
keep touching the FP state, save/restore is inevitable, but in the case
of having one process that does most of the FPU usage, we may actually
be able to do much better than the preloading.
In particular, we may be able to keep track of which CPU the process ran
on last, and also per CPU keep track of which process' FP state that CPU
has. For modern CPU's that don't destroy the FPU contents on save time,
that would allow us to do a lazy restore by just re-enabling the
existing FPU state - with no restore cost at all!
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Thu, 16 Feb 2012 21:33:12 +0000 (13:33 -0800)]
i387: don't ever touch TS_USEDFPU directly, use helper functions
commit
6d59d7a9f5b723a7ac1925c136e93ec83c0c3043 upstream.
This creates three helper functions that do the TS_USEDFPU accesses, and
makes everybody that used to do it by hand use those helpers instead.
In addition, there's a couple of helper functions for the "change both
CR0.TS and TS_USEDFPU at the same time" case, and the places that do
that together have been changed to use those. That means that we have
fewer random places that open-code this situation.
The intent is partly to clarify the code without actually changing any
semantics yet (since we clearly still have some hard to reproduce bug in
this area), but also to make it much easier to use another approach
entirely to caching the CR0.TS bit for software accesses.
Right now we use a bit in the thread-info 'status' variable (this patch
does not change that), but we might want to make it a full field of its
own or even make it a per-cpu variable.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Thu, 16 Feb 2012 20:22:48 +0000 (12:22 -0800)]
i387: move TS_USEDFPU clearing out of __save_init_fpu and into callers
commit
b6c66418dcad0fcf83cd1d0a39482db37bf4fc41 upstream.
Touching TS_USEDFPU without touching CR0.TS is confusing, so don't do
it. By moving it into the callers, we always do the TS_USEDFPU next to
the CR0.TS accesses in the source code, and it's much easier to see how
the two go hand in hand.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Thu, 16 Feb 2012 17:15:04 +0000 (09:15 -0800)]
i387: fix x86-64 preemption-unsafe user stack save/restore
commit
15d8791cae75dca27bfda8ecfe87dca9379d6bb0 upstream.
Commit
5b1cbac37798 ("i387: make irq_fpu_usable() tests more robust")
added a sanity check to the #NM handler to verify that we never cause
the "Device Not Available" exception in kernel mode.
However, that check actually pinpointed a (fundamental) race where we do
cause that exception as part of the signal stack FPU state save/restore
code.
Because we use the floating point instructions themselves to save and
restore state directly from user mode, we cannot do that atomically with
testing the TS_USEDFPU bit: the user mode access itself may cause a page
fault, which causes a task switch, which saves and restores the FP/MMX
state from the kernel buffers.
This kind of "recursive" FP state save is fine per se, but it means that
when the signal stack save/restore gets restarted, it will now take the
'#NM' exception we originally tried to avoid. With preemption this can
happen even without the page fault - but because of the user access, we
cannot just disable preemption around the save/restore instruction.
There are various ways to solve this, including using the
"enable/disable_page_fault()" helpers to not allow page faults at all
during the sequence, and fall back to copying things by hand without the
use of the native FP state save/restore instructions.
However, the simplest thing to do is to just allow the #NM from kernel
space, but fix the race in setting and clearing CR0.TS that this all
exposed: the TS bit changes and the TS_USEDFPU bit absolutely have to be
atomic wrt scheduling, so while the actual state save/restore can be
interrupted and restarted, the act of actually clearing/setting CR0.TS
and the TS_USEDFPU bit together must not.
Instead of just adding random "preempt_disable/enable()" calls to what
is already excessively ugly code, this introduces some helper functions
that mostly mirror the "kernel_fpu_begin/end()" functionality, just for
the user state instead.
Those helper functions should probably eventually replace the other
ad-hoc CR0.TS and TS_USEDFPU tests too, but I'll need to think about it
some more: the task switching functionality in particular needs to
expose the difference between the 'prev' and 'next' threads, while the
new helper functions intentionally were written to only work with
'current'.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Wed, 15 Feb 2012 16:05:18 +0000 (08:05 -0800)]
i387: fix sense of sanity check
commit
c38e23456278e967f094b08247ffc3711b1029b2 upstream.
The check for save_init_fpu() (introduced in commit
5b1cbac37798: "i387:
make irq_fpu_usable() tests more robust") was the wrong way around, but
I hadn't noticed, because my "tests" were bogus: the FPU exceptions are
disabled by default, so even doing a divide by zero never actually
triggers this code at all unless you do extra work to enable them.
So if anybody did enable them, they'd get one spurious warning.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Mon, 13 Feb 2012 21:56:14 +0000 (13:56 -0800)]
i387: make irq_fpu_usable() tests more robust
commit
5b1cbac37798805c1fee18c8cebe5c0a13975b17 upstream.
Some code - especially the crypto layer - wants to use the x86
FP/MMX/AVX register set in what may be interrupt (typically softirq)
context.
That *can* be ok, but the tests for when it was ok were somewhat
suspect. We cannot touch the thread-specific status bits either, so
we'd better check that we're not going to try to save FP state or
anything like that.
Now, it may be that the TS bit is always cleared *before* we set the
USEDFPU bit (and only set when we had already cleared the USEDFP
before), so the TS bit test may actually have been sufficient, but it
certainly was not obviously so.
So this explicitly verifies that we will not touch the TS_USEDFPU bit,
and adds a few related sanity-checks. Because it seems that somehow
AES-NI is corrupting user FP state. The cause is not clear, and this
patch doesn't fix it, but while debugging it I really wanted the code to
be more obviously correct and robust.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Mon, 13 Feb 2012 21:47:25 +0000 (13:47 -0800)]
i387: math_state_restore() isn't called from asm
commit
be98c2cdb15ba26148cd2bd58a857d4f7759ed38 upstream.
It was marked asmlinkage for some really old and stale legacy reasons.
Fix that and the equally stale comment.
Noticed when debugging the irq_fpu_usable() bugs.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Elric Fu [Sat, 18 Feb 2012 05:32:27 +0000 (13:32 +0800)]
USB: Set hub depth after USB3 hub reset
commit
a45aa3b30583e7d54e7cf4fbcd0aa699348a6e5c upstream.
The superspeed device attached to a USB 3.0 hub(such as VIA's)
doesn't respond the address device command after resume. The
root cause is the superspeed hub will miss the Hub Depth value
that is used as an offset into the route string to locate the
bits it uses to determine the downstream port number after
reset, and all packets can't be routed to the device attached
to the superspeed hub.
Hub driver sends a Set Hub Depth request to the superspeed hub
except for USB 3.0 root hub when the hub is initialized and
doesn't send the request again after reset due to the resume
process. So moving the code that sends the Set Hub Depth request
to the superspeed hub from hub_configure() to hub_activate()
is to cover those situations include initialization and reset.
The patch should be backported to kernels as old as 2.6.39.
Signed-off-by: Elric Fu <elricfu1@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sarah Sharp [Mon, 13 Feb 2012 22:42:11 +0000 (14:42 -0800)]
xhci: Fix encoding for HS bulk/control NAK rate.
commit
340a3504fd39dad753ba908fb6f894ee81fc3ae2 upstream.
The xHCI 0.96 spec says that HS bulk and control endpoint NAK rate must
be encoded as an exponent of two number of microframes. The endpoint
descriptor has the NAK rate encoded in number of microframes. We were
just copying the value from the endpoint descriptor into the endpoint
context interval field, which was not correct. This lead to the VIA
host rejecting the add of a bulk OUT endpoint from any USB 2.0 mass
storage device.
The fix is to use the correct encoding. Refactor the code to convert
number of frames to an exponential number of microframes, and make sure
we convert the number of microframes in HS bulk and control endpoints to
an exponent.
This should be back ported to kernels as old as 2.6.31, that contain the
commit
dfa49c4ad120a784ef1ff0717168aa79f55a483a "USB: xhci - fix math
in xhci_get_endpoint_interval"
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Felipe Contreras <felipe.contreras@gmail.com>
Suggested-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sarah Sharp [Thu, 9 Feb 2012 22:43:44 +0000 (14:43 -0800)]
xhci: Fix oops caused by more USB2 ports than USB3 ports.
commit
3278a55a1aebe2bbd47fbb5196209e5326a88b56 upstream.
The code to set the device removable bits in the USB 2.0 roothub
descriptor was accidentally looking at the USB 3.0 port registers
instead of the USB 2.0 registers. This can cause an oops if there are
more USB 2.0 registers than USB 3.0 registers.
This should be backported to kernels as old as 2.6.39, that contain the
commit
4bbb0ace9a3de8392527e3c87926309d541d3b00 "xhci: Return a USB 3.0
hub descriptor for USB3 roothub."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sarah Sharp [Tue, 7 Feb 2012 23:11:46 +0000 (15:11 -0800)]
USB: Fix handoff when BIOS disables host PCI device.
commit
cab928ee1f221c9cc48d6615070fefe2e444384a upstream.
On some systems with an Intel Panther Point xHCI host controller, the
BIOS disables the xHCI PCI device during boot, and switches the xHCI
ports over to EHCI. This allows the BIOS to access USB devices without
having xHCI support.
The downside is that the xHCI BIOS handoff mechanism will fail because
memory mapped I/O is not enabled for the disabled PCI device.
Jesse Barnes says this is expected behavior. The PCI core will enable
BARs before quirks run, but it will leave it in an undefined state, and
it may not have memory mapped I/O enabled.
Make the generic USB quirk handler call pci_enable_device() to re-enable
MMIO, and call pci_disable_device() once the host-specific BIOS handoff
is finished. This will balance the ref counts in the PCI core. When
the PCI probe function is called, usb_hcd_pci_probe() will call
pci_enable_device() again.
This should be back ported to kernels as old as 2.6.31. That was the
first kernel with xHCI support, and no one has complained about BIOS
handoffs failing due to memory mapped I/O being disabled on other hosts
(EHCI, UHCI, or OHCI).
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Oliver Neukum <oneukum@suse.de>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sarah Sharp [Fri, 6 Jan 2012 00:28:54 +0000 (16:28 -0800)]
USB: Remove duplicate USB 3.0 hub feature #defines.
commit
d9f5343e35d9138432657202afa8e3ddb2ade360 upstream.
Somehow we ended up with duplicate hub feature #defines in ch11.h.
Tatyana Brokhman first created the USB 3.0 hub feature macros in 2.6.38
with commit
0eadcc09203349b11ca477ec367079b23d32ab91 "usb: USB3.0 ch11
definitions". In 2.6.39, I modified a patch from John Youn that added
similar macros in a different place in the same file, and committed
dbe79bbe9dcb22cb3651c46f18943477141ca452 "USB 3.0 Hub Changes".
Some of the #defines used different names for the same values. Others
used exactly the same names with the same values, like these gems:
#define USB_PORT_FEAT_BH_PORT_RESET 28
...
#define USB_PORT_FEAT_BH_PORT_RESET 28
According to my very geeky husband (who looked it up in the C99 spec),
it is allowed to have object-like macros with duplicate names as long as
the replacement list is exactly the same. However, he recalled that
some compilers will give warnings when they find duplicate macros. It's
probably best to remove the duplicates in the stable tree, so that the
code compiles for everyone.
The macros are now fixed to move the feature requests that are specific
to USB 3.0 hubs into a new section (out of the USB 2.0 hub feature
section), and use the most common macro name.
This patch should be backported to 2.6.39.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Tatyana Brokhman <tlinder@codeaurora.org>
Cc: John Youn <johnyoun@synopsys.com>
Cc: Jamey Sharp <jamey@minilop.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andrew Lunn [Mon, 20 Feb 2012 08:31:57 +0000 (09:31 +0100)]
USB: Serial: ti_usb_3410_5052: Add Abbot Diabetes Care cable id
commit
7fd25702ba616d9ba56e2a625472f29e5aff25ee upstream.
This USB-serial cable with mini stereo jack enumerates as:
Bus 001 Device 004: ID 1a61:3410 Abbott Diabetes Care
It is a TI3410 inside.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rui li [Tue, 14 Feb 2012 02:35:01 +0000 (10:35 +0800)]
USB: option: cleanup zte 3g-dongle's pid in option.c
commit
b9e44fe5ecda4158c22bc1ea4bffa378a4f83f65 upstream.
1. Remove all old mass-storage ids's pid:
0x0026,0x0053,0x0098,0x0099,0x0149,0x0150,0x0160;
2. As the pid from 0x1401 to 0x1510 which have not surely assigned to
use for serial-port or mass-storage port,so i think it should be
removed now, and will re-add after it have assigned in future;
3. sort the pid to WCDMA and CDMA.
Signed-off-by: Rui li <li.rui27@zte.com.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bruno Thomsen [Tue, 21 Feb 2012 22:41:37 +0000 (23:41 +0100)]
USB: Added Kamstrup VID/PIDs to cp210x serial driver.
commit
c6c1e4491dc8d1ed2509fa6aacffa7f34614fc38 upstream.
Signed-off-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Dumazet [Fri, 18 Nov 2011 20:24:32 +0000 (15:24 -0500)]
ipv4: fix redirect handling
[ Upstream commit
9cc20b268a5a14f5e57b8ad405a83513ab0d78dc ]
commit
f39925dbde77 (ipv4: Cache learned redirect information in
inetpeer.) introduced a regression in ICMP redirect handling.
It assumed ipv4_dst_check() would be called because all possible routes
were attached to the inetpeer we modify in ip_rt_redirect(), but thats
not true.
commit
7cc9150ebe (route: fix ICMP redirect validation) tried to fix
this but solution was not complete. (It fixed only one route)
So we must lookup existing routes (including different TOS values) and
call check_peer_redir() on them.
Reported-by: Ivan Zahariev <famzah@icdsoft.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Flavio Leitner [Mon, 24 Oct 2011 06:56:38 +0000 (02:56 -0400)]
route: fix ICMP redirect validation
[ Upstream commit
7cc9150ebe8ec06cafea9f1c10d92ddacf88d8ae ]
The commit
f39925dbde7788cfb96419c0f092b086aa325c0f
(ipv4: Cache learned redirect information in inetpeer.)
removed some ICMP packet validations which are required by
RFC 1122, section 3.2.2.2:
...
A Redirect message SHOULD be silently discarded if the new
gateway address it specifies is not on the same connected
(sub-) net through which the Redirect arrived [INTRO:2,
Appendix A], or if the source of the Redirect is not the
current first-hop gateway for the specified destination (see
Section 3.3.1).
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Neal Cardwell [Mon, 13 Feb 2012 20:22:08 +0000 (20:22 +0000)]
tcp: fix tcp_shifted_skb() adjustment of lost_cnt_hint for FACK
[ Upstream commit
0af2a0d0576205dda778d25c6c344fc6508fc81d ]
This commit ensures that lost_cnt_hint is correctly updated in
tcp_shifted_skb() for FACK TCP senders. The lost_cnt_hint adjustment
in tcp_sacktag_one() only applies to non-FACK senders, so FACK senders
need their own adjustment.
This applies the spirit of
1e5289e121372a3494402b1b131b41bfe1cf9b7f -
except now that the sequence range passed into tcp_sacktag_one() is
correct we need only have a special case adjustment for FACK.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Neal Cardwell [Sun, 12 Feb 2012 18:37:10 +0000 (18:37 +0000)]
tcp: fix range tcp_shifted_skb() passes to tcp_sacktag_one()
[ Upstream commit
daef52bab1fd26e24e8e9578f8fb33ba1d0cb412 ]
Fix the newly-SACKed range to be the range of newly-shifted bytes.
Previously - since
832d11c5cd076abc0aa1eaf7be96c81d1a59ce41 -
tcp_shifted_skb() incorrectly called tcp_sacktag_one() with the start
and end sequence numbers of the skb it passes in set to the range just
beyond the range that is newly-SACKed.
This commit also removes a special-case adjustment to lost_cnt_hint in
tcp_shifted_skb() since the pre-existing adjustment of lost_cnt_hint
in tcp_sacktag_one() now properly handles this things now that the
correct start sequence number is passed in.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Neal Cardwell [Sun, 12 Feb 2012 18:37:09 +0000 (18:37 +0000)]
tcp: allow tcp_sacktag_one() to tag ranges not aligned with skbs
[ Upstream commit
cc9a672ee522d4805495b98680f4a3db5d0a0af9 ]
This commit allows callers of tcp_sacktag_one() to pass in sequence
ranges that do not align with skb boundaries, as tcp_shifted_skb()
needs to do in an upcoming fix in this patch series.
In fact, now tcp_sacktag_one() does not need to depend on an input skb
at all, which makes its semantics and dependencies more clear.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Shawn Lu [Sat, 4 Feb 2012 12:38:09 +0000 (12:38 +0000)]
tcp_v4_send_reset: binding oif to iif in no sock case
[ Upstream commit
e2446eaab5585555a38ea0df4e01ff313dbb4ac9 ]
Binding RST packet outgoing interface to incoming interface
for tcp v4 when there is no socket associate with it.
when sk is not NULL, using sk->sk_bound_dev_if instead.
(suggested by Eric Dumazet).
This has few benefits:
1. tcp_v6_send_reset already did that.
2. This helps tcp connect with SO_BINDTODEVICE set. When
connection is lost, we still able to sending out RST using
same interface.
3. we are sending reply, it is most likely to be succeed
if iif is used
Signed-off-by: Shawn Lu <shawn.lu@ericsson.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hagen Paul Pfeifer [Sat, 4 Feb 2012 23:22:26 +0000 (23:22 +0000)]
via-velocity: S3 resume fix.
[ Upstream commit
b530b1930bbd9d005345133f0ff0c556d2a52b19 ]
Initially diagnosed on Ubuntu 11.04 with kernel 2.6.38.
velocity_close is not called during a suspend / resume cycle in this
driver and it has no business playing directly with power states.
Signed-off-by: David Lv <DavidLv@viatech.com.cn>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hagen Paul Pfeifer [Wed, 4 Jan 2012 17:35:26 +0000 (17:35 +0000)]
net_sched: Bug in netem reordering
[ Upstream commit
eb10192447370f19a215a8c2749332afa1199d46 ]
Not now, but it looks you are correct. q->qdisc is NULL until another
additional qdisc is attached (beside tfifo). See
50612537e9ab2969312.
The following patch should work.
From: Hagen Paul Pfeifer <hagen@jauu.net>
netem: catch NULL pointer by updating the real qdisc statistic
Reported-by: Vijay Subramanian <subramanian.vijay@gmail.com>
Signed-off-by: Hagen Paul Pfeifer <hagen@jauu.net>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Dumazet [Tue, 14 Feb 2012 10:11:59 +0000 (10:11 +0000)]
netpoll: netpoll_poll_dev() should access dev->flags
[ Upstream commit
58e05f357a039a94aa36475f8c110256f693a239 ]
commit
5a698af53f (bond: service netpoll arp queue on master device)
tested IFF_SLAVE flag against dev->priv_flags instead of dev->flags
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: WANG Cong <amwang@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Graf [Fri, 10 Feb 2012 04:07:11 +0000 (04:07 +0000)]
net: Don't proxy arp respond if iif == rt->dst.dev if private VLAN is disabled
[ Upstream commit
70620c46ac2b45c24b0f22002fdf5ddd1f7daf81 ]
Commit 653241 (net: RFC3069, private VLAN proxy arp support) changed
the behavior of arp proxy to send arp replies back out on the interface
the request came in even if the private VLAN feature is disabled.
Previously we checked rt->dst.dev != skb->dev for in scenarios, when
proxy arp is enabled on for the netdevice and also when individual proxy
neighbour entries have been added.
This patch adds the check back for the pneigh_lookup() scenario.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Julian Anastasov [Sat, 4 Feb 2012 13:04:46 +0000 (13:04 +0000)]
ipv4: reset flowi parameters on route connect
[ Upstream commit
e6b45241c57a83197e5de9166b3b0d32ac562609 ]
Eric Dumazet found that commit
813b3b5db83
(ipv4: Use caller's on-stack flowi as-is in output
route lookups.) that comes in 3.0 added a regression.
The problem appears to be that resulting flowi4_oif is
used incorrectly as input parameter to some routing lookups.
The result is that when connecting to local port without
listener if the IP address that is used is not on a loopback
interface we incorrectly assign RTN_UNICAST to the output
route because no route is matched by oif=lo. The RST packet
can not be sent immediately by tcp_v4_send_reset because
it expects RTN_LOCAL.
So, change ip_route_connect and ip_route_newports to
update the flowi4 fields that are input parameters because
we do not want unnecessary binding to oif.
To make it clear what are the input parameters that
can be modified during lookup and to show which fields of
floiw4 are reused add a new function to update the flowi4
structure: flowi4_update_output.
Thanks to Yurij M. Plotnikov for providing a bug report including a
program to reproduce the problem.
Thanks to Eric Dumazet for tracking the problem down to
tcp_v4_send_reset and providing initial fix.
Reported-by: Yurij M. Plotnikov <Yurij.Plotnikov@oktetlabs.ru>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Li Wei [Thu, 9 Feb 2012 21:15:25 +0000 (21:15 +0000)]
ipv4: Fix wrong order of ip_rt_get_source() and update iph->daddr.
[ Upstream commit
5dc7883f2a7c25f8df40d7479687153558cd531b ]
This patch fix a bug which introduced by commit
ac8a4810 (ipv4: Save
nexthop address of LSRR/SSRR option to IPCB.).In that patch, we saved
the nexthop of SRR in ip_option->nexthop and update iph->daddr until
we get to ip_forward_options(), but we need to update it before
ip_rt_get_source(), otherwise we may get a wrong src.
Signed-off-by: Li Wei <lw@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Li Wei [Tue, 22 Nov 2011 23:33:10 +0000 (23:33 +0000)]
ipv4: Save nexthop address of LSRR/SSRR option to IPCB.
[ Upstream commit
ac8a48106be49c422575ddc7531b776f8eb49610 ]
We can not update iph->daddr in ip_options_rcv_srr(), It is too early.
When some exception ocurred later (eg. in ip_forward() when goto
sr_failed) we need the ip header be identical to the original one as
ICMP need it.
Add a field 'nexthop' in struct ip_options to save nexthop of LSRR
or SSRR option.
Signed-off-by: Li Wei <lw@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Li Wei [Tue, 8 Nov 2011 21:39:28 +0000 (21:39 +0000)]
ipv4: fix for ip_options_rcv_srr() daddr update.
[ Upstream commit
b12f62efb8ec0b9523bdb6c2d412c07193086de9 ]
When opt->srr_is_hit is set skb_rtable(skb) has been updated for
'nexthop' and iph->daddr should always equals to skb_rtable->rt_dst
holds, We need update iph->daddr either.
Signed-off-by: Li Wei <lw@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ben Greear [Fri, 23 Sep 2011 13:11:01 +0000 (13:11 +0000)]
ipv6-multicast: Fix memory leak in IPv6 multicast.
[ Upstream commit
67928c4041606f02725f3c95c4c0404e4532df1b ]
If reg_vif_xmit cannot find a routing entry, be sure to
free the skb before returning the error.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ben Greear [Tue, 27 Sep 2011 19:16:08 +0000 (15:16 -0400)]
ipv6-multicast: Fix memory leak in input path.
[ Upstream commit
2015de5fe2a47086a3260802275932bfd810884e ]
Have to free the skb before returning if we fail
the fib lookup.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Dumazet [Tue, 14 Feb 2012 10:27:09 +0000 (10:27 +0000)]
3c59x: shorten timer period for slave devices
[ Upstream commit
3013dc0cceb9baaf25d5624034eeaa259bf99004 ]
Jean Delvare reported bonding on top of 3c59x adapters was not detecting
network cable removal fast enough.
3c59x indeed uses a 60 seconds timer to check link status if carrier is
on, and 5 seconds if carrier is off.
This patch reduces timer period to 5 seconds if device is a bonding
slave.
Reported-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Graf [Wed, 15 Feb 2012 04:09:46 +0000 (04:09 +0000)]
veth: Enforce minimum size of VETH_INFO_PEER
[ Upstream commit
237114384ab22c174ec4641e809f8e6cbcfce774 ]
VETH_INFO_PEER carries struct ifinfomsg plus optional IFLA
attributes. A minimal size of sizeof(struct ifinfomsg) must be
enforced or we may risk accessing that struct beyond the limits
of the netlink message.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>