OSDN Git Service
Suresh Siddha [Fri, 18 Dec 2009 02:29:46 +0000 (18:29 -0800)]
x86, irq: Allow 0xff for /proc/irq/[n]/smp_affinity on an 8-cpu system
John Blackwood reported:
> on an older Dell PowerEdge 6650 system with 8 cpus (4 are hyper-threaded),
> and 32 bit (x86) kernel, once you change the irq smp_affinity of an irq
> to be less than all cpus in the system, you can never change really the
> irq smp_affinity back to be all cpus in the system (0xff) again,
> even though no error status is returned on the "/bin/echo ff >
> /proc/irq/[n]/smp_affinity" operation.
>
> This is due to that fact that BAD_APICID has the same value as
> all cpus (0xff) on 32bit kernels, and thus the value returned from
> set_desc_affinity() via the cpu_mask_to_apicid_and() function is treated
> as a failure in set_ioapic_affinity_irq_desc(), and no affinity changes
> are made.
set_desc_affinity() is already checking if the incoming cpu mask
intersects with the cpu online mask or not. So there is no need
for the apic op cpu_mask_to_apicid_and() to check again
and return BAD_APICID.
Remove the BAD_APICID return value from cpu_mask_to_apicid_and()
and also fix set_desc_affinity() to return -1 instead of using BAD_APICID
to represent error conditions (as cpu_mask_to_apicid_and() can return
logical or physical apicid values and BAD_APICID is really to represent
bad physical apic id).
Reported-by: John Blackwood <john.blackwood@ccur.com>
Root-caused-by: John Blackwood <john.blackwood@ccur.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <
1261103386.2535.409.camel@sbs-t61>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
H. Peter Anvin [Thu, 17 Dec 2009 23:51:37 +0000 (15:51 -0800)]
Makefile: Unexport LC_ALL instead of clearing it
Apparently not all versions of glibc and utilities treat an empty
LC_ALL as nonexistent, causing error messages to be garbled. Instead,
explicitly unexport it from the environment.
Reported-and-tested-by: Masami Hiramatsu <mhiramat@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
LKML-Reference: <
4B2AC394.
4030108@redhat.com>
Cc: Michal Marek <mmarek@sues.cz>
Cc: Roland Dreier <rdreier@cisco.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
akpm@linux-foundation.org [Thu, 17 Dec 2009 23:26:36 +0000 (15:26 -0800)]
x86: Fix objdump version check in arch/x86/tools/chkobjdump.awk
It says
Warning: objdump version is older than 2.19
Warning: Skipping posttest.
because it used the wrong field from `objdump -v':
akpm:/usr/src/25> /opt/crosstool/gcc-4.0.2-glibc-2.3.6/x86_64-unknown-linux-gnu/bin/x86_64-unknown-linux-gnu-objdump -v
GNU objdump 2.16.1
Copyright 2005 Free Software Foundation, Inc.
This program is free software; you may redistribute it under the terms of
the GNU General Public License. This program has absolutely no warranty.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <
200912172326.nBHNQaQl024796@imap1.linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Masami Hiramatsu <mhiramat@redhat.com>
Pallipadi, Venkatesh [Thu, 17 Dec 2009 20:27:02 +0000 (12:27 -0800)]
x86: Reenable TSC sync check at boot, even with NONSTOP_TSC
Commit
83ce4009 did the following change
If the TSC is constant and non-stop, also set it reliable.
But, there seems to be few systems that will end up with TSC warp across
sockets, depending on how the cpus come out of reset. Skipping TSC sync
test on such systems may result in time inconsistency later.
So, reenable TSC sync test even on constant and non-stop TSC systems.
Set, sched_clock_stable to 1 by default and reset it in
mark_tsc_unstable, if TSC sync fails.
This change still gives perf benefit mentioned in
83ce4009 for systems
where TSC is reliable.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <
20091217202702.GA18015@linux-os.sc.intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Roland Dreier [Thu, 17 Dec 2009 01:39:48 +0000 (17:39 -0800)]
x86: Don't use POSIX character classes in gen-insn-attr-x86.awk
Not all awk implementations (including the default awk in Ubuntu 9.10)
support POSIX character classes. Since x86-opcode-map.txt is plain
ASCII, we can just use explicit ranges for lower case, alphabetic, and
alphanumeric characters instead.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Masami Hiramatsu <mhiramat@redhat.com>
LKML-Reference: <adabphy750b.fsf@roland-alpha.cisco.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
H. Peter Anvin [Thu, 17 Dec 2009 14:56:11 +0000 (06:56 -0800)]
Makefile: set LC_CTYPE, LC_COLLATE, LC_NUMERIC to C
There are a number of common Unix constructs like character ranges in
grep/sed/awk which don't work as expected with LC_COLLATE set to other
than C. Similarly, set LC_CTYPE and LC_NUMERIC to C to avoid other
nasty surprises.
In order to make sure these actually take effect we also have to
clear LC_ALL.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Acked-by: Michal Marek <mmarek@sues.cz>
Acked-by: Masami Hiramatsu <mhiramat@redhat.com>
Acked-by: Roland Dreier <rdreier@cisco.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
LKML-Reference: <
4B2A1761.
4070904@suse.cz>
Yinghai Lu [Wed, 16 Dec 2009 01:59:03 +0000 (17:59 -0800)]
x86: Increase MAX_EARLY_RES; insufficient on 32-bit NUMA
Due to recent changes wakeup and mptable, we run out of early
reservations on 32-bit NUMA. Thus, adjust the available number.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <
4B22D754.
2020706@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Yinghai Lu [Wed, 16 Dec 2009 01:59:02 +0000 (17:59 -0800)]
x86: Fix checking of SRAT when node 0 ram is not from 0
Found one system that boot from socket1 instead of socket0, SRAT get rejected...
[ 0.000000] SRAT: Node 1 PXM 0 0-a0000
[ 0.000000] SRAT: Node 1 PXM 0 100000-
80000000
[ 0.000000] SRAT: Node 1 PXM 0
100000000-
2080000000
[ 0.000000] SRAT: Node 0 PXM 1
2080000000-
4080000000
[ 0.000000] SRAT: Node 2 PXM 2
4080000000-
6080000000
[ 0.000000] SRAT: Node 3 PXM 3
6080000000-
8080000000
[ 0.000000] SRAT: Node 4 PXM 4
8080000000-
a080000000
[ 0.000000] SRAT: Node 5 PXM 5
a080000000-
c080000000
[ 0.000000] SRAT: Node 6 PXM 6
c080000000-
e080000000
[ 0.000000] SRAT: Node 7 PXM 7
e080000000-
10080000000
...
[ 0.000000] NUMA: Allocated memnodemap from 500000 - 701040
[ 0.000000] NUMA: Using 20 for the hash shift.
[ 0.000000] Adding active range (0, 0x2080000, 0x4080000) 0 entries of 3200 used
[ 0.000000] Adding active range (1, 0x0, 0x96) 1 entries of 3200 used
[ 0.000000] Adding active range (1, 0x100, 0x7f750) 2 entries of 3200 used
[ 0.000000] Adding active range (1, 0x100000, 0x2080000) 3 entries of 3200 used
[ 0.000000] Adding active range (2, 0x4080000, 0x6080000) 4 entries of 3200 used
[ 0.000000] Adding active range (3, 0x6080000, 0x8080000) 5 entries of 3200 used
[ 0.000000] Adding active range (4, 0x8080000, 0xa080000) 6 entries of 3200 used
[ 0.000000] Adding active range (5, 0xa080000, 0xc080000) 7 entries of 3200 used
[ 0.000000] Adding active range (6, 0xc080000, 0xe080000) 8 entries of 3200 used
[ 0.000000] Adding active range (7, 0xe080000, 0x10080000) 9 entries of 3200 used
[ 0.000000] SRAT: PXMs only cover 917504MB of your 1048566MB e820 RAM. Not used.
[ 0.000000] SRAT: SRAT not used.
the early_node_map is not sorted because node0 with non zero start come first.
so try to sort it right away after all regions are registered.
also fixs refression by
8716273c (x86: Export srat physical topology)
-v2: make it more solid to handle cross node case like node0 [0,4g), [8,12g) and node1 [4g, 8g), [12g, 16g)
-v3: update comments.
Reported-and-tested-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <
4B2579D2.
3010201@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Suresh Siddha [Thu, 17 Dec 2009 00:25:42 +0000 (16:25 -0800)]
x86, cpuid: Add "volatile" to asm in native_cpuid()
xsave_cntxt_init() does something like:
cpuid(0xd, ..); // find out what features FP/SSE/.. etc are supported
xsetbv(); // enable the features known to OS
cpuid(0xd, ..); // find out the size of the context for features enabled
Depending on what features get enabled in xsetbv(), value of the
cpuid.eax=0xd.ecx=0.ebx changes correspondingly (representing the
size of the context that is enabled).
As we don't have volatile keyword for native_cpuid(), gcc 4.1.2
optimizes away the second cpuid and the kernel continues to use
the cpuid information obtained before xsetbv(), ultimately leading to kernel
crash on processors supporting more state than the legacy FP/SSE.
Add "volatile" for native_cpuid().
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <
1261009542.2745.55.camel@sbs-t61.sc.intel.com>
Cc: stable@kernel.org
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Borislav Petkov [Wed, 16 Dec 2009 23:16:25 +0000 (00:16 +0100)]
x86, msr: msrs_alloc/free for CONFIG_SMP=n
Randy Dunlap reported the following build error:
"When CONFIG_SMP=n, CONFIG_X86_MSR=m:
ERROR: "msrs_free" [drivers/edac/amd64_edac_mod.ko] undefined!
ERROR: "msrs_alloc" [drivers/edac/amd64_edac_mod.ko] undefined!"
This is due to the fact that <arch/x86/lib/msr.c> is conditioned on
CONFIG_SMP and in the UP case we have only the stubs in the header.
Fork off SMP functionality into a new file (msr-smp.c) and build
msrs_{alloc,free} unconditionally.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
LKML-Reference: <
20091216231625.GD27228@liondog.tnic>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Andreas Herrmann [Wed, 16 Dec 2009 14:43:55 +0000 (15:43 +0100)]
x86, amd: Get multi-node CPU info from NodeId MSR instead of PCI config space
Use NodeId MSR to get NodeId and number of nodes per processor.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
LKML-Reference: <
20091216144355.GB28798@alberich.amd.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Sheng Yang [Wed, 16 Dec 2009 05:48:04 +0000 (13:48 +0800)]
x86: Add IA32_TSC_AUX MSR and use it
Clean up write_tsc() and write_tscp_aux() by replacing
hardcoded values.
No change in functionality.
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Cc: Avi Kivity <avi@redhat.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
LKML-Reference: <
1260942485-19156-4-git-send-email-sheng@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
H. Peter Anvin [Tue, 15 Dec 2009 23:13:07 +0000 (15:13 -0800)]
x86, msr/cpuid: Register enough minors for the MSR and CPUID drivers
register_chrdev() hardcodes registering 256 minors, presumably to
avoid breaking old drivers. However, we need to register enough
minors so that we have all possible CPUs.
checkpatch warns on this patch, but the patch is correct: NR_CPUS here
is a static *upper bound* on the *maximum CPU index* (not *number of
CPUs!*) and that is what we want.
Reported-and-tested-by: Russ Anderson <rja@sgi.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
LKML-Reference: <tip-*@git.kernel.org>
Phillip Lougher [Mon, 14 Dec 2009 21:45:19 +0000 (21:45 +0000)]
initramfs: add missing decompressor error check
The decompressors return error by calling a supplied error function, and/or
by returning an error return value. The initramfs code, however, fails to
check the exit code returned by the decompressor, and only checks the error
status set by calling the error function.
This patch adds a return code check and calls the error function.
Signed-off-by: Phillip Lougher <phillip@lougher.demon.co.uk>
LKML-Reference: <
4b26b1ef.0+ZWxT6886olqcSc%phillip@lougher.demon.co.uk>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Phillip Lougher [Mon, 14 Dec 2009 21:45:19 +0000 (21:45 +0000)]
bzip2: Add missing checks for malloc returning NULL
Signed-off-by: Phillip Lougher <phillip@lougher.demon.co.uk>
LKML-Reference: <
4b26b1ef.ln20bM9Mn4gzB21L%phillip@lougher.demon.co.uk>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Phillip Lougher [Mon, 14 Dec 2009 21:45:19 +0000 (21:45 +0000)]
bzip2/lzma/gzip: pre-boot malloc doesn't return NULL on failure
The trivial malloc implementation used in the pre-boot environment by the
decompressors returns a bad pointer on failure (falling through after
calling error). This is doubly wrong - the callers expect malloc to
return NULL on failure, second the error function is intended to be
used by the decompressors to propagate errors to *their* callers. The
decompressors have no access to any state set by the error function.
Signed-off-by: Phillip Lougher <phillip@lougher.demon.co.uk>
LKML-Reference: <
4b26b1ef.hIInb2AYPMtImAJO%phillip@lougher.demon.co.uk>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Jonathan Nieder [Sun, 13 Dec 2009 22:04:38 +0000 (16:04 -0600)]
x86: Fix kprobes build with non-gawk awk
The instruction attribute table generator fails when run by mawk
or original-awk:
$ mawk -f arch/x86/tools/gen-insn-attr-x86.awk \
arch/x86/lib/x86-opcode-map.txt > /dev/null
Semantic error at 240: Second IMM error
$ echo $?
1
Line 240 contains "c8: ENTER Iw,Ib", which indicates that this
instruction has two immediate operands, the second of which is
one byte. The script loops through the immediate operands using
a for loop.
Unfortunately, there is no guarantee in awk that a for (variable
in array) loop will return the indices in increasing order.
Internally, both original-awk and mawk iterate over a hash table
for this purpose, and both implementations happen to produce the
index 2 before 1. The supposed second immediate operand is more
than one byte wide, producing the error.
So loop over the indices in increasing order instead. As a
side-effect, with mawk this means the silly two-entry hash table
never has to be built.
Signed-off-by: Jonathan Nieder <jrnieder@gmail.com>
Acked-by Masami Hiramatsu <mhiramat@redhat.com>
Cc: Jim Keniston <jkenisto@us.ibm.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <
20091213220437.GA27718@progeny.tock>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Ingo Molnar [Tue, 15 Dec 2009 19:33:51 +0000 (20:33 +0100)]
Merge branch 'x86/mce' into x86/urgent
Merge reason: Leftover mini-topic from the merge window - merge it.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Ingo Molnar [Tue, 15 Dec 2009 19:33:22 +0000 (20:33 +0100)]
Merge branch 'x86/asm' into x86/urgent
Merge reason: it's stable so lets push it upstream.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
FUJITA Tomonori [Tue, 15 Dec 2009 11:47:56 +0000 (20:47 +0900)]
x86: Split swiotlb initialization into two stages
The commit
f4780ca005404166cc40af77ef0e86132ab98a81 moves
swiotlb initialization before dma32_free_bootmem(). It's
supposed to fix a bug that the commit
75f1cdf1dda92cae037ec848ae63690d91913eac introduced, we
initialize SWIOTLB right after dma32_free_bootmem so we wrongly
steal memory area allocated for GART with broken BIOS earlier.
However, the above commit introduced another problem, which
likely breaks machines with huge amount of memory. Such a box
use the majority of DMA32_ZONE so there is no memory for
swiotlb.
With this patch, the x86 IOMMU initialization sequence are:
1. We set swiotlb to 1 in the case of (max_pfn > MAX_DMA32_PFN
&& !no_iommu). If swiotlb usage is forced by the boot option,
we go to the step 3 and finish (we don't try to detect IOMMUs).
2. We call the detection functions of all the IOMMUs. The
detection function sets x86_init.iommu.iommu_init to the IOMMU
initialization function (so we can avoid calling the
initialization functions of all the IOMMUs needlessly).
3. We initialize swiotlb (and set dma_ops to swiotlb_dma_ops) if
swiotlb is set to 1.
4. If the IOMMU initialization function doesn't need swiotlb
(e.g. the initialization is sucessful) then sets swiotlb to zero.
5. If we find that swiotlb is set to zero, we free swiotlb
resource.
Reported-by: Yinghai Lu <yinghai@kernel.org>
Reported-by: Roland Dreier <rdreier@cisco.com>
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
LKML-Reference: <
20091215204729A.fujita.tomonori@lab.ntt.co.jp>
Tested-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
H. Peter Anvin [Mon, 14 Dec 2009 21:55:20 +0000 (13:55 -0800)]
x86: Regex support and known-movable symbols for relocs, fix _end
This adds a new category of symbols to the relocs program: symbols
which are known to be relative, even though the linker emits them as
absolute; this is the case for symbols that live in the linker script,
which currently applies to _end.
Unfortunately the previous workaround of putting _end in its own empty
section was defeated by newer binutils, which remove empty sections
completely.
This patch also changes the symbol matching to use regular expressions
instead of hardcoded C for specific patterns.
This is a decidedly non-minimal patch: a modified version of the
relocs program is used as part of the Syslinux build, and this is
basically a backport to Linux of some of those changes; they have
thus been well tested.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
LKML-Reference: <
4AF86211.
3070103@zytor.com>
Acked-by: Michal Marek <mmarek@suse.cz>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
H. Peter Anvin [Mon, 14 Dec 2009 18:02:18 +0000 (10:02 -0800)]
x86, msr: Remove incorrect, duplicated code in the MSR driver
The MSR driver would compute the values for cpu and c at declaration,
and then again in the body of the function. This isn't merely
redundant, but unsafe, since cpu might not refer to a valid CPU at
that point.
Remove the unnecessary and dangerous references in the declarations.
This code now matches the equivalent code in the CPUID driver.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Hidetoshi Seto [Mon, 14 Dec 2009 08:57:00 +0000 (17:57 +0900)]
x86, mce: Clean up thermal init by introducing intel_thermal_supported()
It looks better to have a common function. No change in functionality.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Cc: Cyrill Gorcunov <gorcunov@openvz.org>
LKML-Reference: <
4B25FDDC.407@jp.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Cyrill Gorcunov <gorcunov@openvz.org>
Cyrill Gorcunov [Mon, 14 Dec 2009 08:56:34 +0000 (17:56 +0900)]
x86, mce: Thermal monitoring depends on APIC being enabled
Add check if APIC is not disabled since thermal
monitoring depends on it. As only apic gets disabled
we should not try to install "thermal monitor" vector,
print out that thermal monitoring is enabled and etc...
Note that "Intel Correct Machine Check Interrupts" already
has such a check.
Also I decided to not add cpu_has_apic check into
mcheck_intel_therm_init since even if it'll call apic_read on
disabled apic -- it's safe here and allow us to save a few code
bytes.
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
LKML-Reference: <
4B25FDC2.
3020401@jp.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Yinghai Lu [Mon, 14 Dec 2009 02:52:15 +0000 (11:52 +0900)]
x86: Gart: fix breakage due to IOMMU initialization cleanup
This fixes the following breakage of the commit
75f1cdf1dda92cae037ec848ae63690d91913eac:
- GART systems that don't AGP with broken BIOS and more than 4GB
memory are forced to use swiotlb. They can allocate aperture by
hand and use GART.
- GART systems without GAP must disable GART on shutdown.
- swiotlb usage is forced by the boot option,
gart_iommu_hole_init() is not called, so we disable GART
early_gart_iommu_check().
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
LKML-Reference: <
1260759135-6450-3-git-send-email-fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
FUJITA Tomonori [Mon, 14 Dec 2009 02:52:14 +0000 (11:52 +0900)]
x86: Move swiotlb initialization before dma32_free_bootmem
The commit
75f1cdf1dda92cae037ec848ae63690d91913eac introduced a
bug that we initialize SWIOTLB right after dma32_free_bootmem so
we wrongly steal memory area allocated for GART with broken BIOS
earlier.
This moves swiotlb initialization before dma32_free_bootmem().
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: yinghai@kernel.org
LKML-Reference: <
1260759135-6450-2-git-send-email-fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Joe Perches [Mon, 14 Dec 2009 07:24:03 +0000 (23:24 -0800)]
x86: Fix build warning in arch/x86/mm/mmio-mod.c
Stephen Rothwell reported these warnings:
arch/x86/mm/mmio-mod.c: In function 'print_pte':
arch/x86/mm/mmio-mod.c:100: warning: too many arguments for format
arch/x86/mm/mmio-mod.c:106: warning: too many arguments for format
The 'fmt' was left out accidentally.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Linus <torvalds@linux-foundation.org>
LKML-Reference: <
1260775443.18538.16.camel@Joe-Laptop.home>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
FUJITA Tomonori [Mon, 14 Dec 2009 02:06:15 +0000 (11:06 +0900)]
x86: Remove usedac in feature-removal-schedule.txt
The reason of removal, "replaced by allowdac and no dac
combination" is incorrect. There is no way to do the same thing
with "allowdac" and "nodac" combination.
The usedac option enables us to stop via_no_dac() setting
forbid_dac to 1. That is, someone who uses VIA bridges can use
DAC with this option even if some of VIA bridges seem to be
broken about DAC.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: WANG Cong <amwang@redhat.com>
Cc: gcosta@redhat.com
LKML-Reference: <20091214104423X.fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cliff Wickman [Fri, 11 Dec 2009 17:36:18 +0000 (11:36 -0600)]
x86: Fix duplicated UV BAU interrupt vector
Interrupt vector 0xec has been doubly defined in irq_vectors.h
It seems arbitrary whether LOCAL_PENDING_VECTOR or
UV_BAU_MESSAGE is the higher number. As long as they are
unique. If they are not unique we'll hit a BUG in
alloc_system_vector().
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Cc: <stable@kernel.org>
LKML-Reference: <E1NJ9Pe-0004P7-0Q@eag09.americas.sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
H. Peter Anvin [Fri, 11 Dec 2009 23:48:23 +0000 (15:48 -0800)]
nvram: Fix write beyond end condition; prove to gcc copy is safe
In nvram_write, first of all, correctly handle the case where the file
pointer is already beyond the end; we should return EOF in that case.
Second, make the logic a bit more explicit so that gcc can statically
prove that the copy_from_user() is safe. Once the condition of the
beyond-end filepointer is eliminated, the copy is safe but gcc can't
prove it, causing build failures for i386 allyesconfig.
Third, eliminate the entirely superfluous variable "len", and just use
the passed-in variable "count" instead.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <tip-*@git.kernel.org>
H. Peter Anvin [Tue, 8 Dec 2009 22:01:32 +0000 (14:01 -0800)]
mm: Adjust do_pages_stat() so gcc can see copy_from_user() is safe
Slightly adjust the logic for determining the size of the
copy_form_user() in do_pages_stat(); with this change, gcc can see
that the copying is safe.
Without this, we get a build error for i386 allyesconfig:
/home/hpa/kernel/linux-2.6-tip.urgent/arch/x86/include/asm/uaccess_32.h:213:
error: call to ‘copy_from_user_overflow’ declared with attribute
error: copy_from_user() buffer size is not provably correct
Unlike an earlier patch from Arjan, this doesn't introduce new
variables; merely reshuffles the compare so that gcc can see that an
overflow cannot happen.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Brice Goglin <Brice.Goglin@inria.fr>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
LKML-Reference: <
20090926205406.
30d55b08@infradead.org>
Mike Travis [Fri, 11 Dec 2009 01:19:36 +0000 (17:19 -0800)]
x86: Limit the number of processor bootup messages
When there are a large number of processors in a system, there
is an excessive amount of messages sent to the system console.
It's estimated that with 4096 processors in a system, and the
console baudrate set to 56K, the startup messages will take
about 84 minutes to clear the serial port.
This set of patches limits the number of repetitious messages
which contain no additional information. Much of this information
is obtainable from the /proc and /sysfs. Some of the messages
are also sent to the kernel log buffer as KERN_DEBUG messages so
dmesg can be used to examine more closely any details specific to
a problem.
The new cpu bootup sequence for system_state == SYSTEM_BOOTING:
Booting Node 0, Processors #1 #2 #3 #4 #5 #6 #7 Ok.
Booting Node 1, Processors #8 #9 #10 #11 #12 #13 #14 #15 Ok.
...
Booting Node 3, Processors #56 #57 #58 #59 #60 #61 #62 #63 Ok.
Brought up 64 CPUs
After the system is running, a single line boot message is displayed
when CPU's are hotplugged on:
Booting Node %d Processor %d APIC 0x%x
Status of the following lines:
CPU: Physical Processor ID: printed once (for boot cpu)
CPU: Processor Core ID: printed once (for boot cpu)
CPU: Hyper-Threading is disabled printed once (for boot cpu)
CPU: Thermal monitoring enabled printed once (for boot cpu)
CPU %d/0x%x -> Node %d: removed
CPU %d is now offline: only if system_state == RUNNING
Initializing CPU#%d: KERN_DEBUG
Signed-off-by: Mike Travis <travis@sgi.com>
LKML-Reference: <
4B219E28.
8080601@sgi.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Mike Travis [Fri, 11 Dec 2009 16:08:50 +0000 (08:08 -0800)]
x86: Remove enabling x2apic message for every CPU
Print only once that the system is supporting x2apic mode.
Signed-off-by: Mike Travis <travis@sgi.com>
Acked-by: Cyrill Gorcunov <gorcunov@openvz.org>
LKML-Reference: <
4B226E92.
5080904@sgi.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
H. Peter Anvin [Fri, 11 Dec 2009 22:23:44 +0000 (14:23 -0800)]
doc: Add documentation for bootloader_{type,version}
Add documentation for kernel/bootloader_type and
kernel/bootloader_version to sysctl/kernel.txt. This should really
have been done a long time ago.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Shen Feng <shen@cn.fujitsu.com>
Borislav Petkov [Fri, 11 Dec 2009 17:14:40 +0000 (18:14 +0100)]
x86, msr: Add support for non-contiguous cpumasks
The current rd/wrmsr_on_cpus helpers assume that the supplied
cpumasks are contiguous. However, there are machines out there
like some K8 multinode Opterons which have a non-contiguous core
enumeration on each node (e.g. cores 0,2 on node 0 instead of 0,1), see
http://www.gossamer-threads.com/lists/linux/kernel/
1160268.
This patch fixes out-of-bounds writes (see URL above) by adding per-CPU
msr structs which are used on the respective cores.
Additionally, two helpers, msrs_{alloc,free}, are provided for use by
the callers of the MSR accessors.
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Aristeu Rozanski <aris@redhat.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
LKML-Reference: <
20091211171440.GD31998@aftab>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
H. Peter Anvin [Fri, 11 Dec 2009 18:57:42 +0000 (10:57 -0800)]
Merge commit 'linus/master' into x86/urgent
Yinghai Lu [Thu, 10 Dec 2009 21:07:22 +0000 (13:07 -0800)]
x86: Use find_e820() instead of hard coded trampoline address
Jens found the following crash/regression:
[ 0.000000] found SMP MP-table at [
ffff8800000fdd80] fdd80
[ 0.000000] Kernel panic - not syncing: Overlapping early reservations 12-f011 MP-table mpc to 0-fff BIOS data page
and
[ 0.000000] Kernel panic - not syncing: Overlapping early reservations 12-f011 MP-table mpc to 6000-7fff TRAMPOLINE
and bisected it to
b24c2a9 ("x86: Move find_smp_config()
earlier and avoid bootmem usage").
It turns out the BIOS is using the first 64k for mptable,
without reserving it.
So try to find good range for the real-mode trampoline instead of
hard coding it, in case some bios tries to use that range for sth.
Reported-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Tested-by: Jens Axboe <jens.axboe@oracle.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
LKML-Reference: <
4B21630A.
6000308@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Linus Torvalds [Fri, 11 Dec 2009 05:56:47 +0000 (21:56 -0800)]
Merge branch 'drm-linus' of git://git./linux/kernel/git/airlied/drm-2.6
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (189 commits)
drm/radeon/kms: fix warning about cur_placement being uninitialised.
drm/ttm: Print debug information on memory manager when eviction fails
drm: Add memory manager debug function
drm/radeon/kms: restore surface registers on resume.
drm/radeon/kms/r600/r700: fallback gracefully on ucode failure
drm/ttm: Initialize eviction placement in case the driver callback doesn't
drm/radeon/kms: cleanup structure and module if initialization fails
drm/radeon/kms: actualy set the eviction placements we choose
drm/radeon/kms: Fix NULL ptr dereference
drm/radeon/kms/avivo: add support for new pll selection algo
drm/radeon/kms/avivo: fix some bugs in the display bandwidth setup
drm/radeon/kms: fix return value from fence function.
drm/radeon: Remove tests for -ERESTART from the TTM code.
drm/ttm: Have the TTM code return -ERESTARTSYS instead of -ERESTART.
drm/radeon/kms: Convert radeon to new TTM validation API (V2)
drm/ttm: Rework validation & memory space allocation (V3)
drm: Add search/get functions to get a block in a specific range
drm/radeon/kms: fix avivo tiling regression since radeon object rework
drm/i915: Remove a debugging printk from hangcheck
drm/radeon/kms: make sure i2c id matches
...
Linus Torvalds [Fri, 11 Dec 2009 05:55:54 +0000 (21:55 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/bp/bp
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp: (21 commits)
amd64_edac: bump driver version
amd64_edac: fix use-uninitialised bug
amd64_edac: correct sys address to chip select mapping
amd64_edac: add a leaner syndrome decoding algorithm
amd64_edac: remove early hw support check
amd64_edac: detect DDR3 memory type
edac: add memory types strings for debugging
edac, mce: update AMD F10h revD check
amd64_edac: remove unneeded extract_error_address wrapper
amd64_edac: rename StinkyIdentifier
amd64_edac: remove superfluous dbg printk
amd64_edac: enhance address to DRAM bank mapping
amd64_edac: cleanup f10_early_channel_count
amd64_edac: dump DIMM sizes on K8 too
amd64_edac: cleanup rest of amd64_dump_misc_regs
amd64_edac: cleanup DRAM cfg low debug output
amd64_edac: wrap-up pci config read error handling
amd64_edac: unify MCGCTL ECC switching
cpumask: use modern cpumask style in drivers/edac/amd64_edac.c
amd64_edac: make DRAM regions output more human-readable
...
Linus Torvalds [Fri, 11 Dec 2009 05:55:17 +0000 (21:55 -0800)]
Merge branch 'for-linus' of git://gitorious.org/linux-omap-dss2/linux
* 'for-linus' of git://gitorious.org/linux-omap-dss2/linux:
MAINTAINERS: Add OMAP2/3 DSS and OMAPFB maintainer
OMAP: SDP: Enable DSS2 for OMAP3 SDP board
OMAP: DSS2: Taal DSI command mode panel driver
OMAP: DSS2: Add generic and Sharp panel drivers
OMAP: DSS2: omapfb driver
OMAP: DSS2: DSI driver
OMAP: DSS2: SDI driver
OMAP: DSS2: RFBI driver
OMAP: DSS2: Video encoder driver
OMAP: DSS2: DPI driver
OMAP: DSS2: DISPC
OMAP: DSS2: Add more core files
OMAP: DSS2: Display Subsystem Driver core
OMAP: DSS2: Documentation for DSS2
OMAP: Add support for VRFB rotation engine
OMAP: Add VRAM manager
OMAP: OMAPFB: add omapdss device
OMAP: OMAPFB: split omapfb.h
OMAP2: Add funcs for writing SMS_ROT_* registers
Prarit Bhargava [Wed, 9 Dec 2009 18:36:45 +0000 (13:36 -0500)]
x86, AMD: Fix stale cpuid4_info shared_map data in shared_cpu_map cpumasks
The per_cpu cpuid4_info shared_map can contain stale data when CPUs are added
and removed.
The stale data can lead to a NULL pointer derefernce panic on a remove of a
CPU that has had siblings previously removed.
This patch resolves the panic by verifying a cpu is actually online before
adding it to the shared_cpu_map, only examining cpus that are part of
the same lower level cache, and by updating other siblings lowest level cache
maps when a cpu is added.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
LKML-Reference: <
20091209183336.17855.98708.sendpatchset@prarit.bos.redhat.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Brian Gerst [Wed, 9 Dec 2009 17:34:44 +0000 (12:34 -0500)]
x86: Merge kernel_thread()
Signed-off-by: Brian Gerst <brgerst@gmail.com>
LKML-Reference: <
1260380084-3707-6-git-send-email-brgerst@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Brian Gerst [Wed, 9 Dec 2009 17:34:43 +0000 (12:34 -0500)]
x86: Sync 32/64-bit kernel_thread
Signed-off-by: Brian Gerst <brgerst@gmail.com>
LKML-Reference: <
1260380084-3707-5-git-send-email-brgerst@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Brian Gerst [Wed, 9 Dec 2009 17:34:42 +0000 (12:34 -0500)]
x86, 32-bit: Use same regs as 64-bit for kernel_thread_helper
The arg should be in %eax, but that is clobbered by the return value
of clone. The function pointer can be in any register. Also, don't
push args onto the stack, since regparm(3) is the normal calling
convention now.
Signed-off-by: Brian Gerst <brgerst@gmail.com>
LKML-Reference: <
1260380084-3707-4-git-send-email-brgerst@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Brian Gerst [Wed, 9 Dec 2009 17:34:41 +0000 (12:34 -0500)]
x86, 64-bit: Use user_mode() to determine new stack pointer in copy_thread()
Use user_mode() instead of a magic value for sp to determine when returning
to kernel mode.
Signed-off-by: Brian Gerst <brgerst@gmail.com>
LKML-Reference: <
1260380084-3707-3-git-send-email-brgerst@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Brian Gerst [Wed, 9 Dec 2009 17:34:40 +0000 (12:34 -0500)]
x86, 64-bit: Move kernel_thread to C
Prepare for merging with 32-bit.
Signed-off-by: Brian Gerst <brgerst@gmail.com>
LKML-Reference: <
1260380084-3707-2-git-send-email-brgerst@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Linus Torvalds [Thu, 10 Dec 2009 17:35:44 +0000 (09:35 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/tj/wq
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: Add debugobjects support
Linus Torvalds [Thu, 10 Dec 2009 17:35:02 +0000 (09:35 -0800)]
Merge branch 'bugfix' of git://git./linux/kernel/git/jeremy/xen
* 'bugfix' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen:
xen: try harder to balloon up under memory pressure.
Xen balloon: fix totalram_pages counting.
xen: explicitly create/destroy stop_machine workqueues outside suspend/resume region.
xen: improve error handling in do_suspend.
xen: don't leak IRQs over suspend/resume.
xen: call clock resume notifier on all CPUs
xen: use iret for return from 64b kernel to 32b usermode
xen: don't call dpm_resume_noirq() with interrupts disabled.
xen: register runstate info for boot CPU early
xen: register runstate on secondary CPUs
xen: register timer interrupt with IRQF_TIMER
xen: correctly restore pfn_to_mfn_list_list after resume
xen: restore runstate_info even if !have_vcpu_info_placement
xen: re-register runstate area earlier on resume.
xen: wait up to 5 minutes for device connetion
xen: improvement to wait_for_devices()
xen: fix is_disconnected_device/exists_disconnected_device
xen/xenbus: make DEVICE_ATTR()s static
Linus Torvalds [Thu, 10 Dec 2009 17:34:40 +0000 (09:34 -0800)]
Merge branch 'xen/fbdev' of git://git./linux/kernel/git/jeremy/xen
* 'xen/fbdev' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen:
xen pvfb: Inhibit VM_IO flag to be set on vmalloc-ed framebuffers.
fb-defio: Inhibit VM_IO flag to be set on vmalloc-ed framebuffers.
fb-defio: If FBINFO_VIRTFB is defined, do not set VM_IO flag.
Fix toogle whether xenbus driver should be built as module or part of kernel.
Linus Torvalds [Thu, 10 Dec 2009 17:33:59 +0000 (09:33 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/teigland/dlm
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/dlm:
dlm: always use GFP_NOFS
Linus Torvalds [Thu, 10 Dec 2009 17:33:29 +0000 (09:33 -0800)]
Merge branch 'for_linus' of git://git./linux/kernel/git/tytso/ext4
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (47 commits)
ext4: Fix potential fiemap deadlock (mmap_sem vs. i_data_sem)
ext4: Do not override ext2 or ext3 if built they are built as modules
jbd2: Export jbd2_log_start_commit to fix ext4 build
ext4: Fix insufficient checks in EXT4_IOC_MOVE_EXT
ext4: Wait for proper transaction commit on fsync
ext4: fix incorrect block reservation on quota transfer.
ext4: quota macros cleanup
ext4: ext4_get_reserved_space() must return bytes instead of blocks
ext4: remove blocks from inode prealloc list on failure
ext4: wait for log to commit when umounting
ext4: Avoid data / filesystem corruption when write fails to copy data
ext4: Use ext4 file system driver for ext2/ext3 file system mounts
ext4: Return the PTR_ERR of the correct pointer in setup_new_group_blocks()
jbd2: Add ENOMEM checking in and for jbd2_journal_write_metadata_buffer()
ext4: remove unused parameter wbc from __ext4_journalled_writepage()
ext4: remove encountered_congestion trace
ext4: move_extent_per_page() cleanup
ext4: initialize moved_len before calling ext4_move_extents()
ext4: Fix double-free of blocks with EXT4_IOC_MOVE_EXT
ext4: use ext4_data_block_valid() in ext4_free_blocks()
...
Linus Torvalds [Thu, 10 Dec 2009 17:32:24 +0000 (09:32 -0800)]
Merge branch 'for-linus' of git://git.open-osd.org/linux-open-osd
* 'for-linus' of git://git.open-osd.org/linux-open-osd:
exofs: Multi-device mirror support
exofs: Move all operations to an io_engine
exofs: move osd.c to ios.c
exofs: statfs blocks is sectors not FS blocks
exofs: Prints on mount and unmout
exofs: refactor exofs_i_info initialization into common helper
exofs: dbg-print less
exofs: More sane debug print
trivial: some small fixes in exofs documentation
Linus Torvalds [Thu, 10 Dec 2009 17:31:45 +0000 (09:31 -0800)]
Merge git://git.infradead.org/ubifs-2.6
* git://git.infradead.org/ubifs-2.6:
UBIFS: fix return code in check_leaf
UBI: flush wl before clearing update marker
MAINTAINERS: change e-mail of Artem Bityutskiy
UBIFS: remove manual O_SYNC handling
UBIFS: support mounting of UBI volume character devices
UBI: Add ubi_open_volume_path
David Wong [Thu, 3 Dec 2009 13:54:25 +0000 (10:54 -0300)]
V4L/DVB (13592): max2165: 32bit build patch
This patch drops usage of floating point variable for 32bit build
Signed-off-by: David T. L. Wong <davidtlwong@gmail.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Ingo Molnar [Thu, 10 Dec 2009 13:25:48 +0000 (14:25 +0100)]
Merge branch 'amd-iommu/fixes' of git://git./linux/kernel/git/joro/linux-2.6-iommu into x86/urgent
Joerg Roedel [Thu, 10 Dec 2009 10:12:25 +0000 (11:12 +0100)]
x86/amd-iommu: Fix PCI hotplug with passthrough mode
The device change notifier is initialized in the dma_ops
initialization path. But this path is never executed for
iommu=pt. Move the notifier initialization to IOMMU hardware
init code to fix this.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Joerg Roedel [Thu, 10 Dec 2009 10:03:39 +0000 (11:03 +0100)]
x86/amd-iommu: Fix passthrough mode
The data structure changes to use dev->archdata.iommu field
broke the iommu=pt mode because in this case the
dev->archdata.iommu was left uninitialized. This moves the
inititalization of the devices into the main init function
and fixes the problem.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Boaz Harrosh [Mon, 16 Nov 2009 14:03:05 +0000 (16:03 +0200)]
exofs: Multi-device mirror support
This patch changes on-disk format, it is accompanied with a parallel
patch to mkfs.exofs that enables multi-device capabilities.
After this patch, old exofs will refuse to mount a new formatted FS and
new exofs will refuse an old format. This is done by moving the magic
field offset inside the FSCB. A new FSCB *version* field was added. In
the future, exofs will refuse to mount unmatched FSCB version. To
up-grade or down-grade an exofs one must use mkfs.exofs --upgrade option
before mounting.
Introduced, a new object that contains a *device-table*. This object
contains the default *data-map* and a linear array of devices
information, which identifies the devices used in the filesystem. This
object is only written to offline by mkfs.exofs. This is why it is kept
separate from the FSCB, since the later is written to while mounted.
Same partition number, same object number is used on all devices only
the device varies.
* define the new format, then load the device table on mount time make
sure every thing is supported.
* Change I/O engine to now support Mirror IO, .i.e write same data
to multiple devices, read from a random device to spread the
read-load from multiple clients (TODO: stripe read)
Implementation notes:
A few points introduced in previous patch should be mentioned here:
* Special care was made so absolutlly all operation that have any chance
of failing are done before any osd-request is executed. This is to
minimize the need for a data consistency recovery, to only real IO
errors.
* Each IO state has a kref. It starts at 1, any osd-request executed
will increment the kref, finally when all are executed the first ref
is dropped. At IO-done, each request completion decrements the kref,
the last one to return executes the internal _last_io() routine.
_last_io() will call the registered io_state_done. On sync mode a
caller does not supply a done method, indicating a synchronous
request, the caller is put to sleep and a special io_state_done is
registered that will awaken the caller. Though also in sync mode all
operations are executed in parallel.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Boaz Harrosh [Sun, 8 Nov 2009 12:54:08 +0000 (14:54 +0200)]
exofs: Move all operations to an io_engine
In anticipation for multi-device operations, we separate osd operations
into an abstract I/O API. Currently only one device is used but later
when adding more devices, we will drive all devices in parallel according
to a "data_map" that describes how data is arranged on multiple devices.
The file system level operates, like before, as if there is one object
(inode-number) and an i_size. The io engine will split this to the same
object-number but on multiple device.
At first we introduce Mirror (raid 1) layout. But at the final outcome
we intend to fully implement the pNFS-Objects data-map, including
raid 0,4,5,6 over mirrored devices, over multiple device-groups. And
more. See: http://tools.ietf.org/html/draft-ietf-nfsv4-pnfs-obj-12
* Define an io_state based API for accessing osd storage devices
in an abstract way.
Usage:
First a caller allocates an io state with:
exofs_get_io_state(struct exofs_sb_info *sbi,
struct exofs_io_state** ios);
Then calles one of:
exofs_sbi_create(struct exofs_io_state *ios);
exofs_sbi_remove(struct exofs_io_state *ios);
exofs_sbi_write(struct exofs_io_state *ios);
exofs_sbi_read(struct exofs_io_state *ios);
exofs_oi_truncate(struct exofs_i_info *oi, u64 new_len);
And when done
exofs_put_io_state(struct exofs_io_state *ios);
* Convert all source files to use this new API
* Convert from bio_alloc to bio_kmalloc
* In io engine we make use of the now fixed osd_req_decode_sense
There are no functional changes or on disk additions after this patch.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Boaz Harrosh [Tue, 3 Nov 2009 14:46:00 +0000 (16:46 +0200)]
exofs: move osd.c to ios.c
If I do a "git mv" together with a massive code change
and commit in one patch, git looses the rename and
records a delete/new instead. This is bad because I want
a rename recorded so later rebased/cherry-picked patches
to the old name will work. Also the --follow is lost.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Boaz Harrosh [Mon, 2 Nov 2009 16:19:24 +0000 (18:19 +0200)]
exofs: statfs blocks is sectors not FS blocks
Even though exofs has a 4k block size, statfs blocks
is in sectors (512 bytes).
Also if target returns 0 for capacity then make it
ULLONG_MAX. df does not like zero-size filesystems
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Boaz Harrosh [Thu, 3 Sep 2009 17:38:02 +0000 (20:38 +0300)]
exofs: Prints on mount and unmout
It is important to print in the logs when a filesystem was
mounted and eventually unmounted.
Print the osd-device's osd_name and pid the FS was
mounted/unmounted on.
TODO: How to also print the namespace path the filesystem was
mounted on?
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Boaz Harrosh [Tue, 4 Aug 2009 17:40:29 +0000 (20:40 +0300)]
exofs: refactor exofs_i_info initialization into common helper
There are two places that initialize inodes: exofs_iget() and
exofs_new_inode()
As more members of exofs_i_info that need initialization are
added this code will grow. (soon)
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Boaz Harrosh [Sun, 1 Nov 2009 16:28:14 +0000 (18:28 +0200)]
exofs: dbg-print less
Iner-loops printing is converted to EXOFS_DBG2 which is #defined
to nothing.
It is now almost bareable to just leave debug-on. Every operation
is printed once, with most relevant info (I hope).
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Boaz Harrosh [Tue, 14 Jul 2009 08:06:08 +0000 (11:06 +0300)]
exofs: More sane debug print
debug prints should be somewhat useful without actually
reading the source code
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Thadeu Lima de Souza Cascardo [Mon, 27 Jul 2009 16:26:32 +0000 (13:26 -0300)]
trivial: some small fixes in exofs documentation
Add exofs.txt to filesystems Documentation index and fix some typos,
identation and grammar.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Joe Perches [Wed, 9 Dec 2009 18:45:37 +0000 (10:45 -0800)]
x86: mmio-mod.c: Use pr_fmt
- Add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
- Remove #define NAME
- Remove NAME from pr_<level>
Signed-off-by: Joe Perches <joe@perches.com>
LKML-Reference: <
009cb214c45ef932df0242856228f4739cc91408.
1260383912.git.joe@perches.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Joe Perches [Wed, 9 Dec 2009 18:45:36 +0000 (10:45 -0800)]
x86: kmmio.c: Add and use pr_fmt(fmt)
- Add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
- Strip "kmmio: " from pr_<level>s
Signed-off-by: Joe Perches <joe@perches.com>
LKML-Reference: <
7aa509f8a23933036d39f54bd51e9acc52068049.
1260383912.git.joe@perches.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Joe Perches [Wed, 9 Dec 2009 18:45:35 +0000 (10:45 -0800)]
x86: i8254.c: Add pr_fmt(fmt)
- Add pr_fmt(fmt) "pit: " fmt
- Strip pit: prefixes from pr_debug
Signed-off-by: Joe Perches <joe@perches.com>
LKML-Reference: <
bbd4de532f18bb7c11f64ba20d224c08291cb126.
1260383912.git.joe@perches.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Joe Perches [Wed, 9 Dec 2009 18:45:34 +0000 (10:45 -0800)]
x86: setup_percpu.c: Use pr_<level> and add pr_fmt(fmt)
- Added #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
- Stripped PERCPU: from a pr_warning
Signed-off-by: Joe Perches <joe@perches.com>
LKML-Reference: <
7ead24eccbea8f2b11795abad3e2893a98e1e111.
1260383912.git.joe@perches.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Joe Perches [Wed, 9 Dec 2009 18:45:33 +0000 (10:45 -0800)]
x86: es7000_32.c: Use pr_<level> and add pr_fmt(fmt)
- Added #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
- Converted a few printk(KERN_INFO to pr_info(
- Stripped "es7000_mipcfg" from pr_debug
Signed-off-by: Joe Perches <joe@perches.com>
LKML-Reference: <
3b4375af246dec5941168858910210937c110af9.
1260383912.git.joe@perches.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Dave Airlie [Thu, 10 Dec 2009 05:59:32 +0000 (15:59 +1000)]
drm/radeon/kms: fix warning about cur_placement being uninitialised.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Thu, 10 Dec 2009 05:47:57 +0000 (15:47 +1000)]
Merge remote branch 'korg/drm-radeon-next' of into drm-linus
This merges some TTM overhauls to allow us to do better object placement
for certain radeon GPUs that need scanout+cursor within range of each other,
along with an API change to not return ERESTART to userspace, but to use
ERESTARTSYS properly internally and have it convert to EINTR and catch that
correctly. Also lots of radeon fixes across the board.
Dave Airlie [Thu, 10 Dec 2009 05:44:11 +0000 (15:44 +1000)]
Merge remote branch 'anholt/drm-intel-next' into drm-linus
Pull more Intel changes in, especially one to init the GTT properly
Jerome Glisse [Wed, 9 Dec 2009 20:55:10 +0000 (21:55 +0100)]
drm/ttm: Print debug information on memory manager when eviction fails
This add helper function to print information on eviction placements
and memory manager status when eviction fails to allocate memory
space.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Jerome Glisse [Wed, 9 Dec 2009 20:55:09 +0000 (21:55 +0100)]
drm: Add memory manager debug function
drm_mm_debug_table will print the memory manager state
in table allowing to give a snapshot of the manager at
given point in time. Usefull for debugging.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Wed, 9 Dec 2009 04:15:38 +0000 (14:15 +1000)]
drm/radeon/kms: restore surface registers on resume.
On resume on my rv530 laptop surface cntl was left disabled, so
wierd stuff would happen with rendering to a tiled front buffer.
This checks if the surface regs are assigned to bos and reprograms
the surface registers on resume using the same path that clears
them all on init.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Alex Deucher [Thu, 10 Dec 2009 00:31:44 +0000 (19:31 -0500)]
drm/radeon/kms/r600/r700: fallback gracefully on ucode failure
Sent the wrong patch earlier.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Jerome Glisse [Wed, 9 Dec 2009 21:14:27 +0000 (22:14 +0100)]
drm/ttm: Initialize eviction placement in case the driver callback doesn't
This would allow to catch driver callback error of not properly
setting the eviction placement structure.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Jerome Glisse [Wed, 9 Dec 2009 17:21:55 +0000 (18:21 +0100)]
drm/radeon/kms: cleanup structure and module if initialization fails
This would allow us to properly unload others module like TTM if
initialization fails after we initiliazed TTM structure.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Jerome Glisse [Wed, 9 Dec 2009 20:57:37 +0000 (21:57 +0100)]
drm/radeon/kms: actualy set the eviction placements we choose
Stupid bug, somehow copying the eviction placements into the
result structure was missing.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Jerome Glisse [Wed, 9 Dec 2009 16:39:16 +0000 (17:39 +0100)]
drm/radeon/kms: Fix NULL ptr dereference
radeon_atombios_fini might be call while there is not valid
atombios structure allocated, thus test for a not null ptr
before trying to access this structure.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Alex Deucher [Wed, 9 Dec 2009 22:44:25 +0000 (17:44 -0500)]
drm/radeon/kms/avivo: add support for new pll selection algo
Supported on all AVIVO-based asics.
Can be disabled via the new_pll module parameter:
new_pll=0 - disable
new_pll=1 - enable
enabled by default
[airlied: fixed to use do_div]
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Alex Deucher [Wed, 9 Dec 2009 19:40:06 +0000 (14:40 -0500)]
drm/radeon/kms/avivo: fix some bugs in the display bandwidth setup
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Dave Airlie [Wed, 9 Dec 2009 05:32:23 +0000 (15:32 +1000)]
drm/radeon/kms: fix return value from fence function.
We only want to return here for errors, the wait functions return
a positive timeout otherwise, which gets back to userspace and
causes X to crash here.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Thomas Hellstrom [Mon, 7 Dec 2009 17:36:19 +0000 (18:36 +0100)]
drm/radeon: Remove tests for -ERESTART from the TTM code.
Also sets affected TTM calls up to not wait interruptible, since
that would cause an in-kernel spin until the TTM call succeeds, since
the Radeon code does not return to user-space when a signal is received.
Modifies interruptible fence waits to return -ERESTARTSYS rather than
-EBUSY when interrupted by a signal, since that's the (yet undocumented)
semantics required by the TTM sync object hooks.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Thomas Hellstrom [Mon, 7 Dec 2009 17:36:18 +0000 (18:36 +0100)]
drm/ttm: Have the TTM code return -ERESTARTSYS instead of -ERESTART.
Return -ERESTARTSYS instead of -ERESTART when interrupted by a signal.
The -ERESTARTSYS is converted to an -EINTR by the kernel signal layer
before returned to user-space.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Jerome Glisse [Mon, 7 Dec 2009 14:52:58 +0000 (15:52 +0100)]
drm/radeon/kms: Convert radeon to new TTM validation API (V2)
This convert radeon to use new TTM validation API, it doesn't
really take advantage of it beside in the eviction case.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Jerome Glisse [Tue, 8 Dec 2009 14:33:32 +0000 (15:33 +0100)]
drm/ttm: Rework validation & memory space allocation (V3)
This change allow driver to pass sorted memory placement,
from most prefered placement to least prefered placement.
In order to avoid long function prototype a structure is
used to gather memory placement informations such as range
restriction (if you need a buffer to be in given range).
Range restriction is determined by fpfn & lpfn which are
the first page and last page number btw which allocation
can happen. If those fields are set to 0 ttm will assume
buffer can be put anywhere in the address space (thus it
avoids putting a burden on the driver to always properly
set those fields).
This patch also factor few functions like evicting first
entry of lru list or getting a memory space. This avoid
code duplication.
V2: Change API to use placement flags and array instead
of packing placement order into a quadword.
V3: Make sure we set the appropriate mem.placement flag
when validating or allocation memory space.
[Pending Thomas Hellstrom further review but okay
from preliminary review so far].
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Jerome Glisse [Mon, 7 Dec 2009 14:52:56 +0000 (15:52 +0100)]
drm: Add search/get functions to get a block in a specific range
These are required for changes to TTM.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Tue, 8 Dec 2009 05:45:13 +0000 (15:45 +1000)]
drm/radeon/kms: fix avivo tiling regression since radeon object rework
The object rework moved the tiling flag setup around wrongly,
so tiling we getting setup then overwritten by fb format.
Fixes regression with drm-radeon-next on rv530 laptop tiling test.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Linus Torvalds [Thu, 10 Dec 2009 03:57:06 +0000 (19:57 -0800)]
Merge branch 'acpica' of git://git./linux/kernel/git/lenb/linux-acpi-2.6
* 'acpica' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPICA: Update version to
20091112.
ACPICA: Add additional module-level code support
ACPICA: Deploy new create integer interface where appropriate
ACPICA: New internal utility function to create Integer objects
ACPICA: Add repair for predefined methods that must return sorted lists
ACPICA: Fix possible fault if return Package objects contain NULL elements
ACPICA: Add post-order callback to acpi_walk_namespace
ACPICA: Change package length error message to an info message
ACPICA: Reduce severity of predefined repair messages, Warning to Info
ACPICA: Update version to
20091013
ACPICA: Fix possible memory leak for Scope ASL operator
ACPICA: Remove possibility of executing _REG methods twice
ACPICA: Add repair for bad _MAT buffers
ACPICA: Add repair for bad _BIF/_BIX packages
Linus Torvalds [Thu, 10 Dec 2009 03:53:11 +0000 (19:53 -0800)]
Merge branch 'hwmon-for-linus' of git://git./linux/kernel/git/jdelvare/staging
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging: (41 commits)
hwmon: (adt7475) Add VID support for the ADT7476
hwmon: (adt7475) Add an entry in MAINTAINERS
hwmon: (adt7475) Add support for the ADT7476
hwmon: (adt7475) Voltage attenuators can be bypassed
hwmon: (adt7475) Print device information on probe
hwmon: (adt7475) Handle alternative pin functions
hwmon: (adt7475) Move sysfs files removal to a separate function
hwmon: (adt7475) Add support for the ADT7490
hwmon: (adt7475) Improve device detection
hwmon: (adt7475) Add missing static marker
hwmon: (adt7475) Rework voltage inputs handling
hwmon: (adt7475) Implement pwm_use_point2_pwm_at_crit
hwmon: (adt7475) New documentation
hwmon: (adt7475) Add support for the ADT7473
hwmon: (f71882fg) Add support for the f71889fg (version 2)
hwmon: (f71882fg) Fix sysfs file removal
hwmon: (f71882fg) Cleanup sysfs attr creation 2/2
hwmon: (f71882fg) Cleanup sysfs attr creation 1/2
hwmon: (thmc50) Stop using I2C_CLIENT_MODULE_PARM
hwmon: Add Freescale MC13783 ADC driver
...
Linus Torvalds [Thu, 10 Dec 2009 03:52:13 +0000 (19:52 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: ice1724 - aureon - modify WM8770 Master & DAC volume
ALSA: hda/realtek: quirk for D945GCLF2 mainboard
ALSA: hda - Terradici HDA controllers does not support 64-bit mode
ALSA: document: Add direct git link to grub hda-analyzer
ALSA: radio/sound/miro: fix build, cleanup depends/selects
ALSA: hda - Generalize EAPD inversion check in patch_analog.c
ASoC: Wrong variable returned on error
ALSA: snd-usb-us122l: add product IDs of US-122MKII and US-144MKII
ALSA: hda - Exclude unusable ADCs for ALC88x
ALSA: hda - Add missing Line-Out and PCM switches as slave
ALSA: hda - iMac 9,1 sound patch.
ALSA: opti93x: set MC indirect registers base from PnP data
Linus Torvalds [Thu, 10 Dec 2009 03:52:01 +0000 (19:52 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (51 commits)
Input: appletouch - give up maintainership
Input: dm355evm_kbd - switch to using sparse keymap library
Input: wistron_btns - switch to using sparse keymap library
Input: add generic support for sparse keymaps
Input: fix memory leak in force feedback core
Input: wistron - remove identification strings from DMI table
Input: psmouse - remove identification strings from DMI tables
Input: atkbd - remove identification strings from DMI table
Input: i8042 - remove identification strings from DMI tables
DMI: allow omitting ident strings in DMI tables
Input: psmouse - do not carry DMI data around
Input: matrix-keypad - switch to using dev_pm_ops
Input: keyboard - fix lack of locking when traversing handler->h_list
Input: gpio_keys - scan gpio state at probe and resume time
Input: keyboard - add locking around event handling
Input: usbtouchscreen - add support for ET&T TC5UH touchscreen controller
Input: xpad - add two new Xbox 360 devices
Input: polled device - do not start polling if interval is zero
Input: polled device - schedule first poll immediately
Input: add S3C24XX touchscreen driver
...
Linus Torvalds [Thu, 10 Dec 2009 03:50:49 +0000 (19:50 -0800)]
Merge branch 'for_linus' of git://git./linux/kernel/git/mchehab/linux-2.6
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (345 commits)
V4L/DVB (13542): ir-keytable: Allow dynamic table change
V4L/DVB (13541): atbm8830: replace 64-bit division and floating point usage
V4L/DVB (13540): ir-common: Cleanup get key evdev code
V4L/DVB (13539): ir-common: add __func__ for debug messages
V4L/DVB (13538): ir-common: Use a dynamic keycode table
V4L/DVB (13537): ir: Prepare the code for dynamic keycode table allocation
V4L/DVB (13536): em28xx: Use the full RC5 code on HVR-950 Remote Controller
V4L/DVB (13535): ir-common: Add a hauppauge new table with the complete RC5 code
V4L/DVB (13534): ir-common: Remove some unused fields/structs
V4L/DVB (13533): ir: use dynamic tables, instead of static ones
V4L/DVB (13532): ir-common: Add infrastructure to use a dynamic keycode table
V4L/DVB (13531): ir-common: rename the debug routine to allow exporting it
V4L/DVB (13458): go7007: subdev conversion
V4L/DVB (13457): s2250: subdev conversion
V4L/DVB (13456): s2250: Change module structure
V4L/DVB (13528): em28xx: add support for em2800 VC211A card
em28xx: don't reduce scale to half size for em2800
em28xx: don't load audio modules when AC97 is mis-detected
em28xx: em2800 chips support max width of 640
V4L/DVB (13523): dvb-bt8xx: fix compile warning
...
Fix up trivial conflicts due to spelling fixes from the trivial tree in
Documentation/video4linux/gspca.txt
drivers/media/video/cx18/cx18-mailbox.h
Linus Torvalds [Thu, 10 Dec 2009 03:46:12 +0000 (19:46 -0800)]
Merge branch 'next-i2c' of git://git.fluff.org/bjdooks/linux
* 'next-i2c' of git://git.fluff.org/bjdooks/linux: (25 commits)
i2c-pnx: Map I2C adapter number to platform ID number
i2c-omap: OMAP3: PM: (re)init for every transfer to support off-mode
i2c-designware: i2c_dw_handle_tx_abort: Use dev_dbg() for NOACK cases
i2c-designware: Cosmetic cleanups
i2c-designware: Tx abort cleanups
i2c-designware: Skip RX_FULL and TX_EMPTY bits on tx abort errors
i2c-designware: i2c_dw_xfer_msg: Fix error handling procedures
i2c-designware: Disable TX_EMPTY when all i2c_msg msgs has been processed
i2c-designware: Process all i2c_msg messages in the interrupt handler
i2c-designware: i2c_dw_read: Remove redundant target address checker
i2c-designware: i2c_dw_func: Set I2C_FUNC_SMBUS_foo bits
i2c-designware: Initialize byte count variables just prior to being used
i2c-designware: i2c_dw_xfer_msg: Introduce a local "buf" pointer
i2c-designware: Divide i2c_dw_xfer_msg into two functions
i2c-designware: Enable RX_FULL interrupt
i2c-designware: Set Tx/Rx FIFO threshold levels
i2c-designware: Process i2c_msg messages in the interrupt handler
i2c-designware: i2c_dw_xfer_msg: Fix i2c_msg search bug
i2c-designware: Improved _HCNT/_LCNT calculation
i2c-designware: Remove an useless local variable "num"
...
Linus Torvalds [Thu, 10 Dec 2009 03:45:58 +0000 (19:45 -0800)]
Merge branch 's3c24xx-updates' of git://git.fluff.org/bjdooks/linux
* 's3c24xx-updates' of git://git.fluff.org/bjdooks/linux:
ARM: S3C24XX: DMA: Use valid index when accessing array
ARM: S3C: move s3c_pwm_remove to .devexit.text
ARM: S3C24XX: Export s3c24xx_set_fiq for modules.
ARM: S3C: move s3c_adc_remove to .devexit.text
Linus Torvalds [Thu, 10 Dec 2009 03:45:38 +0000 (19:45 -0800)]
Merge git://git./linux/kernel/git/davem/ide-next-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide-next-2.6:
sl82c105: remove no longer needed debugging code
sis5513: remove stale TODO
pdc202xx_old: remove no longer needed debugging code
cy82c693: remove no longer needed debugging code
cmd64x: remove no longer needed debugging code
alim15x3: remove obsolete and dangerous wdc_udma parameter
ide: Increase WAIT_DRQ to accomodate some CF cards and SSD drives.
cs5535: add pci id for AMD based CS5535 controllers
slc90e66: fix UDMA handling
drivers/ide/tx4938ide.c: use resource_size()
drivers/ide/ide_platform.c: use resource_size()
drivers/ide/au1xxx-ide.c: use resource_size()
hpt366: remove dead old timing tables
ide: update Kconfig text to mark as deprecated
ide-tape: remove the BKL
hpt366: kill unused #define's
Linus Torvalds [Thu, 10 Dec 2009 03:43:33 +0000 (19:43 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jikos/trivial
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (42 commits)
tree-wide: fix misspelling of "definition" in comments
reiserfs: fix misspelling of "journaled"
doc: Fix a typo in slub.txt.
inotify: remove superfluous return code check
hdlc: spelling fix in find_pvc() comment
doc: fix regulator docs cut-and-pasteism
mtd: Fix comment in Kconfig
doc: Fix IRQ chip docs
tree-wide: fix assorted typos all over the place
drivers/ata/libata-sff.c: comment spelling fixes
fix typos/grammos in Documentation/edac.txt
sysctl: add missing comments
fs/debugfs/inode.c: fix comment typos
sgivwfb: Make use of ARRAY_SIZE.
sky2: fix sky2_link_down copy/paste comment error
tree-wide: fix typos "couter" -> "counter"
tree-wide: fix typos "offest" -> "offset"
fix kerneldoc for set_irq_msi()
spidev: fix double "of of" in comment
comment typo fix: sybsystem -> subsystem
...