OSDN Git Service
Gertjan van Wingerde [Tue, 11 May 2010 21:51:41 +0000 (23:51 +0200)]
rt2x00: Dump beacons under a different identifier than TX frames.
This allows for specific identification of beacons in the debugfs
frame stream.
Preparation for later differences between dumped TX frames and dumped
beacons.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gertjan van Wingerde [Tue, 11 May 2010 21:51:40 +0000 (23:51 +0200)]
rt2x00: Simplify TXD handling of beacons.
The handling of tx descriptors for beacons can be simplified by updating
write_tx_desc implementations of each driver to write directly to the
queue entry descriptor instead of to a provided memory area.
This is also a preparation for further clean ups where descriptors are
properly reserved in the skb instead of fiddling with the skb data
pointer.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gertjan van Wingerde [Tue, 11 May 2010 21:51:39 +0000 (23:51 +0200)]
rt2x00: Re-order tx descriptor writing code in drivers.
Where possible, write the tx descriptor words from start to end, to
follow a logical ordering of words.
Where this is not possible (in rt2400pci, rt2500pci and rt61pci) add
a comment as to why word 0 needs to be written last.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gertjan van Wingerde [Tue, 11 May 2010 21:51:38 +0000 (23:51 +0200)]
rt2x00: Fix beacon descriptor writing for rt61pci.
The buffer address descriptor word is not part of the TXINFO structure
needed for beacons. The current writing of that word for beacons is
therefore an out-of-bounds write.
Fix this by only writing the buffer address descriptor word for TX
queues.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gertjan van Wingerde [Tue, 11 May 2010 21:51:37 +0000 (23:51 +0200)]
rt2x00: Consistently name skb frame descriptor skbdesc.
The skb frame descriptor is called everywhere skbdesc, except in one
place in rt2x00debug_dump_frame. Change that occurence to have
consistent naming.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Steve Tanner [Tue, 11 May 2010 21:34:16 +0000 (14:34 -0700)]
ar9170usb: add vendor and device ID for Qwest/Actiontec 802AIN Wireless N USB Network Adapter
* add support for the Qwest/Actiontec 802AIN Wireless N USB Network Adapter.
lsusb identifies the device as: "ID 1668:1200 Actiontec Electronics, Inc. [hex]"
usb_modeswitch package and appropriate rules are required to switch
the device from "ID 0ace:20ff ZyDas"
Changes-licensed-under: GPL
Signed-off-by: Steve Tanner <steve.tanner@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Julia Lawall [Tue, 11 May 2010 18:25:56 +0000 (20:25 +0200)]
drivers/net/wireless/hostap: Drop memory allocation cast
Drop cast on the result of kmalloc and similar functions.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
type T;
@@
- (T *)
(\(kmalloc\|kzalloc\|kcalloc\|kmem_cache_alloc\|kmem_cache_zalloc\|
kmem_cache_alloc_node\|kmalloc_node\|kzalloc_node\)(...))
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Abhijeet Kolekar [Tue, 11 May 2010 18:22:11 +0000 (11:22 -0700)]
mac80211: fix paged defragmentation
Paged RX skb patch broke the defragmentation. We need to read hdr again
after linearization.
It fixes following bug
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2194
Signed-off-by: Zhu, Yi <yi.zhu@intel.com>
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Tue, 11 May 2010 15:23:03 +0000 (17:23 +0200)]
ath9k_hw: clean up EEPROM endian handling on AR9003
Remove the double swapping of the descriptor data structure, instead
keep it little-endian (native format of the eeprom data), and byteswap
on access.
This allows sparse to verify endian access to the eeprom struct.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Tue, 11 May 2010 15:23:02 +0000 (17:23 +0200)]
ath9k: add debugfs files for reading/writing registers
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Tue, 11 May 2010 15:23:01 +0000 (17:23 +0200)]
ath9k: add debugfs files for reading/writing the rx and tx chainmask
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau [Tue, 11 May 2010 15:23:00 +0000 (17:23 +0200)]
ath9k: use debugfs_remove_recursive() instead of keeping pointers to all entries
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith.Manoharan@atheros.com [Tue, 11 May 2010 11:33:36 +0000 (17:03 +0530)]
ath9k_htc: Fix array overflow
Use ENDPOINT_MAX instead of HST_ENDPOINT_MAX.
This fixes a stack corruption issue.
This is based on a patch sent by Dan Carpenter <error27@gmail.com>.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith.Manoharan@atheros.com [Tue, 11 May 2010 10:54:43 +0000 (16:24 +0530)]
ath9k_htc: Fix target ready race condition
The ready message from the target could be processed
before the host HW init has completed. In this case,
htc_process_target_rdy() would assume the target has timed
out, when it hasn't. Fix this by checking if the target
has sent the ready message properly.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith.Manoharan@atheros.com [Tue, 11 May 2010 10:54:41 +0000 (16:24 +0530)]
ath9k_htc: Reorder HTC initialization
The HTC state has to be setup before initializing
the target because the ready message could possibly
come before the control endpoints in HTC have been
identified.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith.Manoharan@atheros.com [Tue, 11 May 2010 10:54:40 +0000 (16:24 +0530)]
ath9k_htc: Allocate URBs properly
The URBs have to be allocated before uploading
the firmware to the target. This is needed to process
the target ready message properly.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith.Manoharan@atheros.com [Tue, 11 May 2010 10:54:38 +0000 (16:24 +0530)]
ath9k_htc: Lock sta_notify() callback
Since ->sta_notify() can sleep, protect
the callback with a mutex.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy [Thu, 6 May 2010 03:34:02 +0000 (20:34 -0700)]
mac80211: check channel switch mode for future frames transmit
Check the mode in channel switch ie for either 0 or 1 on transmission.
A channel switch mode set to 1 means that the STA in a BSS to which the
frame containing the element is addressed shall transmit no further
frames within the BSS until the scheduled channel switch.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Tue, 11 May 2010 14:20:57 +0000 (16:20 +0200)]
mac80211: add offload channel switch support
This adds support for offloading the channel switch
operation to devices that support such, typically
by having specific firmware API for it. The reasons
for this could be that the firmware provides better
timing or that regulatory enforcement done by the
device requires special handling of CSAs.
In order to allow drivers to specify the timing to
the device, the new channel_switch callback will
pass through the received frame's mactime, where
available.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vasanthakumar Thiagarajan [Tue, 11 May 2010 02:41:35 +0000 (19:41 -0700)]
ath9k: Remove unused rx_edma in ath_rx_addbuffer_edma()
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vasanthakumar Thiagarajan [Tue, 11 May 2010 02:41:34 +0000 (19:41 -0700)]
ath9k: Fix bug in handling rx frames with invalid descriptor content
Don't send them for further processing.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Tue, 11 May 2010 01:42:11 +0000 (21:42 -0400)]
ath9k_hw: new initialization values for AR9003
These changes include:
* For PAPRD, the TXRF3.capdiv5G, TXRF3.rdiv5G and TXRF3.rdiv2G
are set to 0x0, the TXRF6.capdiv2G is set to 0x2 for all
three chains.
* The d2cas5G/d3cas5G/d4cas5G was updated to 4/4/4 in lowest_ob_db
Tx gain table.
* To improve DPPM, three parameters were updated (Released from Madhan):
1. RANGE_OSDAC is set to 0x1 for 2G, 0x0 for 5G
2. offsetC1 is set to 0xc
3. inv_clk320_adc is set to 0x1
* To reduce PHY error(from spur), cycpwr_thr1 and cycpwr_thr1_ext
are increased to 0x8 at 2G.
* The 2G Rx gain tables are updated with mixer gain setting 3,1,0.
The new checksums yield:
initvals -f ar9003
0x00000000c2bfa7d5 ar9300_2p0_radio_postamble
0x00000000ada2b114 ar9300Modes_lowest_ob_db_tx_gain_table_2p0
0x00000000e0bc2c84 ar9300Modes_fast_clock_2p0
0x00000000056eaf74 ar9300_2p0_radio_core
0x0000000000000000 ar9300Common_rx_gain_table_merlin_2p0
0x0000000078658fb5 ar9300_2p0_mac_postamble
0x0000000023235333 ar9300_2p0_soc_postamble
0x0000000054d41904 ar9200_merlin_2p0_radio_core
0x00000000748572cf ar9300_2p0_baseband_postamble
0x000000009aa5a0a4 ar9300_2p0_baseband_core
0x000000003df9a326 ar9300Modes_high_power_tx_gain_table_2p0
0x000000001cfba124 ar9300Modes_high_ob_db_tx_gain_table_2p0
0x0000000011302700 ar9300Common_rx_gain_table_2p0
0x00000000e3eab114 ar9300Modes_low_ob_db_tx_gain_table_2p0
0x00000000c9d66d40 ar9300_2p0_mac_core
0x000000001e1d0800 ar9300Common_wo_xlna_rx_gain_table_2p0
0x00000000a0c54980 ar9300_2p0_soc_preamble
0x00000000292e2544 ar9300PciePhy_pll_on_clkreq_disable_L1_2p0
0x000000002d3e2544 ar9300PciePhy_clkreq_enable_L1_2p0
0x00000000293e2544 ar9300PciePhy_clkreq_disable_L1_2p0
Cc: Don Breslin <don.breslin@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Mon, 10 May 2010 19:26:27 +0000 (15:26 -0400)]
ath5k: drop warning on jumbo frames
Jumbo frames are not supported, and if they are seen it is likely
a bogus frame so just silently discard them instead of warning on
them all time. Also, instead of dropping them immediately though
move the check *after* we check for all sort of frame errors. This
should enable us to discard these frames if the hardware picks
other bogus items first. Lets see if we still get those jumbo
counters increasing still with this.
Jumbo frames would happen if we tell hardware we can support
a small 802.11 chunks of DMA'd frame, hardware would split RX'd
frames into parts and we'd have to reconstruct them in software.
This is done with USB due to the bulk size but with ath5k we
already provide a good limit to hardware and this should not be
happening.
This is reported quite often and if it fills the logs then this
needs to be addressed and to avoid spurious reports.
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Carpenter [Sat, 8 May 2010 16:26:38 +0000 (18:26 +0200)]
wl1271: remove some unneeded code
The goto and the break are equivelent. I removed the goto in memory of
Edsger Dijkstra who famously hated gotos and who would have been eighty
years old next Tuesday.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Carpenter [Sat, 8 May 2010 16:25:51 +0000 (18:25 +0200)]
wl1271: fix notifier interface supported test
The "(wl == NULL)" test doesn't work here because "wl" is always
non-null. The intent of the code is to return if the interface
was not supported by the driver.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Carpenter [Sat, 8 May 2010 16:25:17 +0000 (18:25 +0200)]
wl1271: add missing spin_lock()
We should start the loop consistently with the "wl_lock" lock held.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg [Fri, 7 May 2010 08:49:15 +0000 (01:49 -0700)]
iwlwifi: clear driver stations when going down
During a hw restart, mac80211 will attempt to
reconfigure all stations. Currently, that fails
and leads to warnings because we still have the
stations marked active. Therefore, clear all
stations when doing down.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Johannes Berg [Fri, 30 Apr 2010 18:30:50 +0000 (11:30 -0700)]
iwlwifi: remove pointless HT check
Remove the check before invoking iwl_set_ht_add_station(),
since neither of the conditions in this check makes sense,
as either we pass in a NULL ht_info (first branch) or in
the IBSS case an ht_info with ht_enabled=false.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Johannes Berg [Fri, 30 Apr 2010 18:30:49 +0000 (11:30 -0700)]
iwlwifi: rename iwl_add_local_station
This function is now only used for the special
IBSS BSSID station, so rename it to indicate
this. The new name is iwl_add_bssid_station.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Johannes Berg [Fri, 30 Apr 2010 18:30:48 +0000 (11:30 -0700)]
iwlwifi: move iwl_find_station() to 4965
4965 code is the only thing that now still
needs iwl_find_station(), so move it there
and make it static. Everything else can
rely on the station data passed by mac80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Johannes Berg [Fri, 30 Apr 2010 20:53:37 +0000 (13:53 -0700)]
iwlwifi: use iwl_sta_id() for TKIP key update
With the station ID being stored in the
station struct, which mac80211 gives us
for TKIP phase 1 key updates, we can also
remove the use of iwl_find_station() in
that code path.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Johannes Berg [Fri, 30 Apr 2010 18:30:46 +0000 (11:30 -0700)]
iwlagn: use iwl_sta_id() for aggregation
With the station ID being stored in the
station struct, which mac80211 gives us
for aggregation callbacks, we can also
remove the use of iwl_find_station() in
those code paths.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Johannes Berg [Fri, 30 Apr 2010 18:30:45 +0000 (11:30 -0700)]
iwlwifi: use iwl_find_station less
Since we now store the station ID in each station
struct, many places need not look at the station
table any more since they can just pull the station
ID out of the struct. Remove iwl_get_sta_id() and
use iwl_sta_id() instead as appropriate.
This reduces the amount of code needed to find the
right station significantly, and works since
mac80211 passes the station only after it has been
fully initialised, ie. even if TX races with
station addition it will only be passed to TX once
the addition is complete.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Johannes Berg [Fri, 30 Apr 2010 18:30:44 +0000 (11:30 -0700)]
iwlwifi: add iwl_sta_id()
In places where the station struct is
guaranteed to exist (presumably), use
this helper to get the station ID out
of it (and warn if there's no station
struct after all).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Johannes Berg [Fri, 30 Apr 2010 18:30:43 +0000 (11:30 -0700)]
iwlwifi: track station IDs
mac80211 allows us to store private data per
station, so put the station ID there. This
allows us to avoid the station ID lookup when
removing regular stations. To also be able to
avoid the lookup to remove the special IBSS
BSSID station, track its ID in the per-vif
private data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Wey-Yi Guy [Fri, 30 Apr 2010 18:35:16 +0000 (11:35 -0700)]
iwlwifi: provide more comments for cfg structure
Provide comments for newly added cfg parameters
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Wey-Yi Guy [Fri, 30 Apr 2010 18:35:15 +0000 (11:35 -0700)]
iwlwifi: "tx power per chain" are part of ucode_tx_stats
Move "tx power per chain" into ucode_tx_stats, it is debugging
information provided by uCode as part of statistics notification.
The "tx power per chain" parameters are optional parameters which only
supported by 6000 series device today; those are reserved fields for all
the other devices.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Reinette Chatre [Tue, 13 Apr 2010 23:11:19 +0000 (16:11 -0700)]
iwlagn: work around rate scaling reset delay
When station is using an HT channel to communicate to AP and communication
is lost then driver will first be notified that channel is not an HT
channel anymore before AP station is removed. A consequence of that is that
the driver will know that it is not communicating on HT anymore, but the
rate scaling table is still under the impression it is operating in HT. Any
time after driver has been notified channel is not HT anymore there will
thus be a firmware SYSASSERT when the current active LQ command is sent.
A workaround for this issue is to not send a LQ command in the short time between
being notified channel is not HT anymore and rate scaling table being
updated.
This fixes http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2173
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Johannes Berg [Thu, 29 Apr 2010 07:53:29 +0000 (00:53 -0700)]
iwlwifi: rework broadcast station management
Currently, the broadcast station is managed along
with the interface type, rather than always being
present. That leads to a bug with injection -- it
is currently not possible to inject frames when
the only virtual interface is a monitor, because
in that the required broadcast station is missing.
Additionally, allocating and deallocating the
broadcast station's LQ all the time is wasteful,
and the code to support this is fairly complex.
So this changes completely the way we manage the
broadcast station. Rather than manage it along
with any interface, we now allocate it when we
bring the device up, and remove it again when we
bring the device down. When we bring the device
up, we don't immediately program the broadcast
station into it, instead we just mark it active
and rely on the next restore cycle to upload it
to the device. This works because an unassociated
RXON is always required at least once to set up
device parameters, which implies a reprogramming
of stations into the device.
As we now manage all stations properly, there no
longer is a need for forcing a clearing of them
via iwl_clear_ucode_stations(), which can become
a lot simpler.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Johannes Berg [Thu, 29 Apr 2010 17:41:07 +0000 (10:41 -0700)]
iwlwifi: split allocation/sending local station LQ
Rename iwl_sta_init_lq to iwl_sta_alloc_lq and
move sending it out into the caller.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Johannes Berg [Wed, 28 Apr 2010 21:44:45 +0000 (14:44 -0700)]
iwlwifi: fix iwl_sta_init_lq station ID
The "is_ap" argument to iwl_sta_init_lq is never true,
so it and the corresponding code can be removed. However,
it needs to have the station ID because it is also used
for the IBSS BSSID station, and that doesn't have the
broadcast ID.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Johannes Berg [Thu, 29 Apr 2010 11:43:10 +0000 (04:43 -0700)]
iwlwifi: note that priv->bssid is used only by 3945
The bssid member of struct iwl_priv is now
only used by 3945 code, so note that. It
shouldn't be used by any other code in the
future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Johannes Berg [Thu, 29 Apr 2010 11:43:09 +0000 (04:43 -0700)]
iwlwifi: use vif in iwl_ht_conf
Pass the virtual interface pointer to iwl_ht_conf()
so it doesn't need to rely on iw_mode and other
global variables.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Johannes Berg [Thu, 29 Apr 2010 11:43:08 +0000 (04:43 -0700)]
iwlwifi: remove useless priv->vif check
This check is not useful, since we now no
longer dereference priv->vif at this spot.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Johannes Berg [Thu, 29 Apr 2010 11:43:07 +0000 (04:43 -0700)]
iwlagn: use virtual interface in TX aggregation handling
Most of the TX aggregation handling can be passed
the virtual interface directly instead of having
to rely on priv->vif.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Johannes Berg [Thu, 29 Apr 2010 11:43:06 +0000 (04:43 -0700)]
iwlwifi: push virtual interface through
Rather than keeping every bit of information
around in priv and the virtual interface, add
a virtual interface to many functions and use
the information directly from it.
This removes beacon_int, assoc_capability and
assoc_id from struct iwl_priv.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Johannes Berg [Thu, 29 Apr 2010 11:43:05 +0000 (04:43 -0700)]
iwlwifi: apply filter flags directly
Since iwl_configure_filter can now sleep since
the mac80211 callback was changed, we can now
apply filter flags changes directly.
Also, while at it, make the code a bit more
generic with a local macro. There's no need
to check changed_flags since we apply all at
the same time anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Johannes Berg [Thu, 29 Apr 2010 11:43:04 +0000 (04:43 -0700)]
iwlagn: use vif->type to check station
We need not check iw_mode, since we have
the vif pointer available.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Johannes Berg [Thu, 29 Apr 2010 11:43:03 +0000 (04:43 -0700)]
iwlagn: move iwl_get_ra_sta_id to 4965
This function is only needed by 4965, so
it need not be in core code and can be
made static.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Johannes Berg [Thu, 29 Apr 2010 11:43:02 +0000 (04:43 -0700)]
iwlwifi: remove rts_threshold
We never use that member of struct iwl_priv.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Abhijeet Kolekar [Wed, 28 Apr 2010 22:47:04 +0000 (15:47 -0700)]
iwl3945: add plcp error checking
Add plcp error checking for 3945. After threshold of plcp
is reached , it resets the radio
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Johannes Berg [Thu, 29 Apr 2010 06:33:10 +0000 (23:33 -0700)]
iwlagn: implement loading a new firmware file type
The old firmware file type does not allow indicating
any firmware capabilities, which we frequently want
to make things easier.
This implements a new firmware type that is based on
a TLV structure, and adds a TLV for the maximum length
of probe requests in scans.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Johannes Berg [Wed, 28 Apr 2010 19:09:16 +0000 (12:09 -0700)]
iwlagn: prepare for new firmware file format
Currently the first four bytes in a firmware file
indicate the major, minor and api versions as well
as the serial number. These combined can never be
zero, so we can use that special case for a new,
future, file format.
This patch simply shuffles the code and prepares
for that new format.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Johannes Berg [Wed, 28 Apr 2010 19:09:15 +0000 (12:09 -0700)]
iwlwifi: move eeprom version printout to eeprom init
It doesn't belong into firmware loading,
it should instead be printed after loading
the EEPROM.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Johannes Berg [Wed, 28 Apr 2010 19:09:14 +0000 (12:09 -0700)]
iwlwifi: remove ucode virtual functions
AGN devices all use the same ucode operations,
except for 4965, because 4965 uses only v1 file
headers.
Therefore, we can remove all the indirection
we have here and just code the API distinction
in place, with a small special case for 4965.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Johannes Berg [Wed, 28 Apr 2010 19:09:13 +0000 (12:09 -0700)]
iwl3945: remove ucode access indirection
As these function pointers will always point to
the 3945 functions, we can just call them directly
and avoid the indirection.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Johannes Berg [Wed, 28 Apr 2010 19:09:12 +0000 (12:09 -0700)]
iwlagn: show and store firmware build number
We currently display the build number only if debugging
is enabled, but it is really helpful so show it all the
time. Also store it so it can be retrieved later via
ethtool.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Johannes Berg [Wed, 28 Apr 2010 15:44:52 +0000 (08:44 -0700)]
iwlwifi: manage IBSS station properly
Currently iwlwifi will eventually exhaust the station
table when adding the BSSID station for IBSS mode,
unless the interface is set down.
The new mac80211 ibss joined/left notification allows
us to fix that easily by moving the code to add the
IBSS station to the notification, and also adding
code to remove it again when we leave the IBSS.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Johannes Berg [Wed, 28 Apr 2010 15:44:51 +0000 (08:44 -0700)]
iwlwifi: pass address to iwl_remove_station
We'll need that function for IBSS station management,
so pass it the address, which is the only thing it
uses from the station struct.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Johannes Berg [Wed, 28 Apr 2010 15:44:50 +0000 (08:44 -0700)]
iwl3945: use iwl3945_add_bcast_station
iwl3945 should not use iwl_add_local_station(..., false)
because that would leave the IWL_STA_UCODE_INPROGRESS flag
set for the station, which is not desirable. Instead it
can use iwl3945_add_bcast_station() here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Reinette Chatre [Fri, 23 Apr 2010 17:33:33 +0000 (10:33 -0700)]
iwlwifi: make bcast LQ command available for later restore actions
When adding the broadcast station the link quality command is
generated on demand, sent to device, and disappears. It is thus not
available for later cases when we need to restore stations and need
to send the link quality command afterwards. Now, when first adding the
broadcast station, also generate its link quality command to always be
available for later restoring.
Also fix an issue when adding local stations where the "in progress" state
is never cleared.
Reported-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Shanyu Zhao [Wed, 28 Apr 2010 05:05:15 +0000 (22:05 -0700)]
iwlwifi: dump firmware build info in error case
Dump the firmware version and build number in case of firmware SW
error. This would help firmware engineer analyze the error log.
Requested-by: Jay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Wey-Yi Guy [Wed, 28 Apr 2010 01:43:33 +0000 (18:43 -0700)]
iwlwifi: checking for all the possible failure cases
Multiple error condition require fw/rf reset, driver should check all
the possible errors as long as the error checking functions for the
devices are available.
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Wey-Yi Guy [Tue, 27 Apr 2010 21:10:00 +0000 (14:10 -0700)]
iwlwifi: wimax co-exist code clean up
wifi/wimax co-exist command is part of _agn device configuration
sequence; move it to iwl-agn-ucode.c which is more appropriate place for the
function.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Wey-Yi Guy [Mon, 26 Apr 2010 23:08:27 +0000 (16:08 -0700)]
iwlwifi: give correct return information for tx power debugfs
Return -EAGAIN when request tx power information and uCode is not ready;
so it will not confuse with tx power information not available.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Wey-Yi Guy [Sun, 25 Apr 2010 22:41:43 +0000 (15:41 -0700)]
iwlwifi: use cfg to configure calibration operation
sensitivity calibration and chain noise calibration are not available
for all the devices; use .cfg to configure the availability of those
calibration functions
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Wey-Yi Guy [Tue, 27 Apr 2010 21:00:28 +0000 (14:00 -0700)]
iwlwifi: use .cfg to enable/disable continuous ucode trace
Instead of checking device type for enable/disable continuous ucode
trace function; put it in .cfg for better control and more
flexibilities.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Wey-Yi Guy [Tue, 27 Apr 2010 21:33:33 +0000 (14:33 -0700)]
iwlwifi: remove device type checking for tx power in debugfs
Instead of checking device type for enable/disable tx power control,
move it to .cfg for better control and more flexibilities.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Johannes Berg [Tue, 27 Apr 2010 10:36:15 +0000 (03:36 -0700)]
iwlwifi: use vif iwl_bss_info_changed
The iw_mode will always follow the only vif we
have, but using the vif directly seems easier.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Wey-Yi Guy [Tue, 27 Apr 2010 00:20:07 +0000 (17:20 -0700)]
iwlwifi: rename "tx_power" to "chain_tx_power"
The "chain_tx_power" debugfs function is to display the tx power per
chain based. Name it "tx_power" is misleading.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Wey-Yi Guy [Sun, 25 Apr 2010 16:39:46 +0000 (09:39 -0700)]
iwlwifi: remove powersave debugfs if it is not supported
For the devices do not have power save support, remove the power save
control related debugfs files.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Abhijeet Kolekar [Fri, 23 Apr 2010 21:14:53 +0000 (14:14 -0700)]
iwl3945: fix scan races
Port following patch to 3945.
"commit
90c4162ff59a3281b6d2f7206740be6217bd6758
Author: Johannes Berg <johannes.berg@intel.com>
Date: Wed Apr 7 00:21:36 2010 -0700
iwlwifi: fix scan races"
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Shanyu Zhao [Wed, 21 Apr 2010 18:46:33 +0000 (11:46 -0700)]
iwlwifi: rename 6000 series Gen2 devices to Gen2a
Rename the current 6000 series Gen2 devices to Gen2a.
Rename the ucode name prefix to iwlwifi-6000g2a.
Also corrected the device IDs for Gen2a series devices.
Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Reinette Chatre [Mon, 10 May 2010 22:08:11 +0000 (15:08 -0700)]
Merge branch 'wireless-2.6' into wireless-next-2.6
Conflicts:
drivers/net/wireless/iwlwifi/iwl-dev.h
Johannes Berg [Thu, 29 Apr 2010 14:41:53 +0000 (07:41 -0700)]
iwlagn: wait for asynchronous firmware loading
When we kick off a firmware loading process,
and then unbind from the pci device right
away, we get into trouble. Avoid that by
waiting for the firmware loading to finish
(whether successfully or not) before the
unbind in iwl_pci_remove.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Randy Dunlap [Mon, 10 May 2010 16:24:29 +0000 (09:24 -0700)]
wireless: depends on NET
When CONFIG_NET is disabled, the attempt to build wext-priv.c
fails with:
net/wireless/wext-priv.c: In function 'ioctl_private_call':
net/wireless/wext-priv.c:207: error: implicit declaration of function 'call_commit_handler'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Xose Vazquez Perez [Mon, 10 May 2010 09:35:36 +0000 (11:35 +0200)]
wireless: rt2x00: rt2800usb: replace X by x
s/X/x
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gertjan van Wingerde [Sun, 9 May 2010 19:24:22 +0000 (21:24 +0200)]
rt2x00: Clean up generic procedures on descriptor writing.
With a little bit of restructuring it isn't necessary to have special
cases in rt2x00queue_write_tx_descriptor for writing the descriptor
for beacons.
Simply split off the kicking of the TX queue to a separate function
with is only called for non-beacons.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gertjan van Wingerde [Sat, 8 May 2010 21:40:26 +0000 (23:40 +0200)]
rt2x00: Fix beaconing on rt2800.
According to the Ralink vendor driver for rt2800 we don't need a full
TXD for a beacon but just a TXWI in front of the actual beacon.
Fix the rt2800pci and rt2800usb beaconing code accordingly.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gertjan van Wingerde [Sat, 8 May 2010 21:40:25 +0000 (23:40 +0200)]
rt2x00: provide beacon's txdesc to write_beacon callback function.
Preparation to fix rt2800 beaconing.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gertjan van Wingerde [Sat, 8 May 2010 21:40:24 +0000 (23:40 +0200)]
rt2x00: Clean up all driver's kick_tx_queue callback functions.
All of the driver's kick_tx_queue callback functions treat the TX queue
for beacons in a special manner.
Clean this up by integrating the kicking of the beacon queue into the
write_beacon callback function, and let the generic code no longer call
the kick_tx_queue callback function when updating the beacon.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gertjan van Wingerde [Sat, 8 May 2010 21:40:22 +0000 (23:40 +0200)]
rt2x00: Factor out RXWI processing to common rt2800 code.
RXWI processing is exactly the same for rt2800pci and rt2800usb, so
make it common code.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gertjan van Wingerde [Sat, 8 May 2010 21:40:21 +0000 (23:40 +0200)]
rt2x00: Factor out TXWI writing to common rt2800 code.
TXWI writing is exactly the same for rt2800pci and rt2800usb, so
make it common code.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gertjan van Wingerde [Sat, 8 May 2010 21:40:20 +0000 (23:40 +0200)]
rt2x00: Don't check whether hardware crypto is enabled when reading RXD.
We should simply follow what the hardware told us it has done.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gertjan van Wingerde [Sat, 8 May 2010 21:40:19 +0000 (23:40 +0200)]
rt2x00: Clean up rt2800usb.h.
Remove unused RXD_DESC_SIZE define and remove duplicated RXWI definitions
from rt2800.h.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Gertjan van Wingerde [Sat, 8 May 2010 21:40:18 +0000 (23:40 +0200)]
rt2x00: Fix setting of txdesc->length field.
We should take the stripping of the IV into account for the txdesc->length
field.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Tested-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Carpenter [Sat, 8 May 2010 16:24:38 +0000 (18:24 +0200)]
ath5k: several off by one range checks
There are several places that use > ARRAY_SIZE() instead of
>= ARRAY_SIZE().
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Carpenter [Sat, 8 May 2010 16:24:02 +0000 (18:24 +0200)]
ath9k/htc_drv_main: off by one error
I changed "> ATH9K_HTC_MAX_TID" to ">= ATH9K_HTC_MAX_TID" to avoid a
potential overflow.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Carpenter [Sat, 8 May 2010 16:23:20 +0000 (18:23 +0200)]
ath9k/htc_drv_main: null dereference typo
This is a stray null dereference. We initialize "ista" properly later on.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dan Carpenter [Sat, 8 May 2010 16:21:01 +0000 (18:21 +0200)]
iwlwifi: remove stray mutex_unlock()
This mutex_unlock() has been here from the initial commit, but as nearly
as I can tell, there isn't a reason for it.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Fri, 7 May 2010 22:23:22 +0000 (18:23 -0400)]
ath9k_hw: enable PCIe low power mode for AR9003
Cc: Paul Shaw <paul.shaw@atheros.com>
Cc: Don Breslin <don.breslin@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville [Mon, 10 May 2010 18:24:34 +0000 (14:24 -0400)]
rtl8180: change PCI DMA mask to DMA_BIT_MASK(32)
From the original report:
"I had problems to get my rtl8185 PCI card running on Sparc64: I always
got an error about "No suitable DMA available" followed by an error
that no device could be detected. When comparing the rtl8180 driver to
others I noticed that others are mostly using DMA_BIT_MASK so I changed
the custom mask to DMA_BIT_MASK(32) which fixed my issue."
Reported-by: Tiziano Müller <tm@dev-zero.ch>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Helmut Schaa [Fri, 7 May 2010 09:03:08 +0000 (11:03 +0200)]
rt2x00: rt2800: use correct txop value in tx descriptor
rt2800 devices use a different enumeration to specify what IFS values should
be used on frame transmission compared to the other rt2x00 devices. Hence,
create a new enum called txop that contains the valid values.
Furthermore use the appropriate txop values as found in the ralink drivers:
- TXOP_BACKOFF for management frames
- TXOP_SIFS for subsequent fragments in a burst
- TXOP_HTTXOP for all data frames
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Fri, 7 May 2010 08:39:02 +0000 (11:39 +0300)]
wl1271: Reduce PSM entry hang over period from 128 => 1 ms
Currently, we configure a 128ms hang over period for the PSM entry
(the firmware will remain active for 128ms after sending the null func for
PSM and getting an ack for it.) This is a huge power consumption issue, and
appears unnecessary. So, configure the value to 1 ms.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Janne Ylalehto <janne.ylalehto@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Teemu Paasikivi [Fri, 7 May 2010 08:39:01 +0000 (11:39 +0300)]
wl1271: Increase timeout for command event waiting
Incresed the timeout value for command complete event waiting from 100
ms to 750 ms. In some rare cases it can take about 600 ms before
complete event for join command is received. This is most propably
caused by the firmware being busy with scanning related activities.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Fri, 7 May 2010 08:39:00 +0000 (11:39 +0300)]
wl1271: Fix to join and channel number handling
This patch changes the way JOIN's are performed, and channel numbers updated.
The reason for this is that the firmware JOIN command clears WPA(2) key
material, and if done while associated to a WPA(2) secured AP, will render
the data-path unusable.
While the channel is not usually changed while associated (and currently we
could not even support something like that), after performing a scan operation
while associated, mac80211 will re-set the current channel to the driver. This
caused our problem.
Also, the mac80211 is assuming that the driver channel configuration remains
persistent over periods of IDLE. Therefore remove channel resetting to zero
from the unjoin function.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Fri, 7 May 2010 08:38:59 +0000 (11:38 +0300)]
wl1271: Fix 32 bit register read related endiannes bug
Reading single registers did not pay attention to data endianness. This patch
fix that.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Juuso Oikarinen [Fri, 7 May 2010 08:38:58 +0000 (11:38 +0300)]
wl1271: Add sysfs file to retrieve HW PG-version and ROM-version
This patch reads the HW PG version (along with a ROM-version, embedded in the
same value) from the wl1271 hardware and publishes the value in a sysfs -file.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith [Fri, 7 May 2010 08:07:57 +0000 (13:37 +0530)]
ath9k_htc: Handle IDLE LED properly
Switch LED off/on when handling CONF_CHANGE_IDLE.
Not doing this would leave the radio LED on even
though the chip would be in full sleep mode.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez [Fri, 7 May 2010 02:41:14 +0000 (22:41 -0400)]
ath9k_hw: Update initvals for AR9003 for xb113
Generated using the new shiny intivals-tool [1]:
initvals -w -f ar9003 > ar9003_initvals.h
The respective checksums are:
0x000000005a76829d ar9300_2p0_radio_postamble
0x000000009d90cb74 ar9300Modes_lowest_ob_db_tx_gain_table_2p0
0x00000000e0bc2c84 ar9300Modes_fast_clock_2p0
0x00000000852fca34 ar9300_2p0_radio_core
0x0000000000000000 ar9300Common_rx_gain_table_merlin_2p0
0x0000000078658fb5 ar9300_2p0_mac_postamble
0x0000000023235333 ar9300_2p0_soc_postamble
0x0000000054d41904 ar9200_merlin_2p0_radio_core
0x00000000618455d4 ar9300_2p0_baseband_postamble
0x000000009aa590a4 ar9300_2p0_baseband_core
0x000000004783d946 ar9300Modes_high_power_tx_gain_table_2p0
0x000000006681db44 ar9300Modes_high_ob_db_tx_gain_table_2p0
0x000000001f318700 ar9300Common_rx_gain_table_2p0
0x000000009990cb74 ar9300Modes_low_ob_db_tx_gain_table_2p0
0x00000000c9d66d40 ar9300_2p0_mac_core
0x0000000039139500 ar9300Common_wo_xlna_rx_gain_table_2p0
0x00000000a0c54980 ar9300_2p0_soc_preamble
0x00000000292e2544 ar9300PciePhy_pll_on_clkreq_disable_L1_2p0
0x000000002d3e2544 ar9300PciePhy_clkreq_enable_L1_2p0
0x00000000293e2544 ar9300PciePhy_clkreq_disable_L1_2p0
[1] http://wireless.kernel.org/en/users/Drivers/ath9k_hw/initvals-tool
Cc: Tom Hammel <thammel@atheros.com>
Cc: Enis Akay <Enis.Akay@Atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>