OSDN Git Service
Grzegorz Siwik [Fri, 29 Mar 2019 22:08:35 +0000 (15:08 -0700)]
i40e: Fix the typo in adding 40GE KR4 mode
This patch fixes the typo in I40E_CAP_PHY_TYPE mode link code.
It was fixed by changing 40000baseLR4_Full to 40000baseKR4_Full
Signed-off-by: Grzegorz Siwik <grzegorz.siwik@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Grzegorz Siwik [Fri, 29 Mar 2019 22:08:32 +0000 (15:08 -0700)]
i40e: Setting VF to VLAN 0 requires restart
This patch fixes a bug where changing VLAN to 0 was not set until VF
restart.
Now we are setting pvid info to 0 when we have to change VLAN to 0.
Without this change when VF VLAN was changed to 0 nothing happened until
VF restart. For changing to VLAN different than 0 it worked correctly.
Signed-off-by: Grzegorz Siwik <grzegorz.siwik@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Aleksandr Loktionov [Fri, 29 Mar 2019 22:08:31 +0000 (15:08 -0700)]
i40e: add new pci id for X710/XXV710 N3000 cards
New device ids are created to support X710/XXV710 N3000 cards.
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Grzegorz Siwik [Fri, 29 Mar 2019 22:08:30 +0000 (15:08 -0700)]
i40e: VF's promiscuous attribute is not kept
This patch fixes a bug where the promiscuous mode was not being
kept when the VF switched to a new VLAN.
Now we are config two times a promiscuous mode when we switch VLAN.
Without this change when we change VF VLAN we still receive
all the packets from previous VLAN and only unicast from new VLAN.
Signed-off-by: Grzegorz Siwik <grzegorz.siwik@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Eelco Chaudron [Thu, 2 May 2019 20:12:38 +0000 (16:12 -0400)]
net: openvswitch: return an error instead of doing BUG_ON()
For all other error cases in queue_userspace_packet() the error is
returned, so it makes sense to do the same for these two error cases.
Reported-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Eelco Chaudron <echaudro@redhat.com>
Acked-by: Flavio Leitner <fbl@sysclose.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Thu, 2 May 2019 18:46:52 +0000 (20:46 +0200)]
r8169: remove rtl_write_exgmac_batch
rtl_write_exgmac_batch is used in only one place, so we can remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 4 May 2019 05:27:11 +0000 (01:27 -0400)]
Merge branch 'netlink-strict-attribute-checking-follow-up'
Michal Kubecek says:
====================
netlink: strict attribute checking follow-up
Three follow-up patches for recent strict netlink validation series.
Patch 1 fixes dump handling for genetlink families which validate and parse
messages themselves (e.g. because they need different policies for diferent
commands).
Patch 2 sets bad_attr in extack in one place where this was omitted.
Patch 3 adds new NL_VALIDATE_NESTED flags for strict validation to enable
checking that NLA_F_NESTED value in received messages matches expectations
and includes this flag in NL_VALIDATE_STRICT. This would change userspace
visible behavior but the previous switching to NL_VALIDATE_STRICT for new
code is still only in net-next at the moment.
v2: change error messages to mention NLA_F_NESTED explicitly
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kubecek [Thu, 2 May 2019 14:15:10 +0000 (16:15 +0200)]
netlink: add validation of NLA_F_NESTED flag
Add new validation flag NL_VALIDATE_NESTED which adds three consistency
checks of NLA_F_NESTED_FLAG:
- the flag is set on attributes with NLA_NESTED{,_ARRAY} policy
- the flag is not set on attributes with other policies except NLA_UNSPEC
- the flag is set on attribute passed to nla_parse_nested()
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
v2: change error messages to mention NLA_F_NESTED explicitly
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kubecek [Thu, 2 May 2019 14:15:10 +0000 (16:15 +0200)]
netlink: set bad attribute also on maxtype check
The check that attribute type is within 0...maxtype range in
__nla_validate_parse() sets only error message but not bad_attr in extack.
Set also bad_attr to tell userspace which attribute failed validation.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michal Kubecek [Thu, 2 May 2019 14:15:10 +0000 (16:15 +0200)]
genetlink: do not validate dump requests if there is no policy
Unlike do requests, dump genetlink requests now perform strict validation
by default even if the genetlink family does not set policy and maxtype
because it does validation and parsing on its own (e.g. because it wants to
allow different message format for different commands). While the null
policy will be ignored, maxtype (which would be zero) is still checked so
that any attribute will fail validation.
The solution is to only call __nla_validate() from genl_family_rcv_msg()
if family->maxtype is set.
Fixes:
ef6243acb478 ("genetlink: optionally validate strictly/dumps")
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 4 May 2019 05:21:36 +0000 (01:21 -0400)]
Merge branch 'mlxsw-Firmware-version-update'
Ido Schimmel says:
====================
mlxsw: Firmware version update
This patchset updates mlxsw to use a new firmware version and adds
support for split into two ports on Spectrum-2 based systems.
Patch #1 updates the firmware version to 13.2000.1122
Patch #2 queries new resources from the firmware.
Patch #3 makes use of these resources in order to support split into two
ports on Spectrum-2 based systems. The need for these resources is
explained by Shalom:
When splitting a port, different local ports need to be mapped on different
systems. For example:
SN3700 (local_ports_in_2x=2):
* Without split:
front panel 1 --> local port 1
front panel 2 --> local port 5
* Split to 2:
front panel 1s0 --> local port 1
front panel 1s1 --> local port 3
front panel 2 --> local port 5
SN3800 (local_ports_in_2x=1):
* Without split:
front panel 1 --> local port 1
front panel 2 --> local port 3
* Split to 2:
front panel 1s0 --> local port 1
front panel 1s1 --> local port 2
front panel 2 --> local port 3
The local_ports_in_{1x, 2x} resources provide the offsets from the base
local ports according to which the new local ports can be calculated.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Shalom Toledo [Thu, 2 May 2019 11:13:09 +0000 (14:13 +0300)]
mlxsw: spectrum: split base on local_ports_in_{1x, 2x} resources
When splitting a port, different local ports need to be mapped on different
systems. For example:
SN3700 (local_ports_in_2x=2):
* Without split:
front panel 1 --> local port 1
front panel 2 --> local port 5
* Split to 2:
front panel 1s0 --> local port 1
front panel 1s1 --> local port 3
front panel 2 --> local port 5
SN3800 (local_ports_in_2x=1):
* Without split:
front panel 1 --> local port 1
front panel 2 --> local port 3
* Split to 2:
front panel 1s0 --> local port 1
front panel 1s1 --> local port 2
front panel 2 --> local port 3
The local_ports_in_{1x, 2x} resources provide the offsets from the base
local ports according to which the new local ports can be calculated.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shalom Toledo [Thu, 2 May 2019 11:13:08 +0000 (14:13 +0300)]
mlxsw: resources: Add local_ports_in_{1x, 2x}
Since the number of local ports in 4x changed between SPC and SPC-2,
firmware expose new resources that the driver can query.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Thu, 2 May 2019 11:13:07 +0000 (14:13 +0300)]
mlxsw: Bump firmware version to 13.2000.1122
The new version supports two features that are required by upcoming
changes in the driver:
* Querying of new resources allowing port split into two ports on
Spectrum-2 systems
* Querying of number of gearboxes on supported systems such as SN3800
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tuong Lien [Thu, 2 May 2019 10:23:23 +0000 (17:23 +0700)]
tipc: fix missing Name entries due to half-failover
TIPC link can temporarily fall into "half-establish" that only one of
the link endpoints is ESTABLISHED and starts to send traffic, PROTOCOL
messages, whereas the other link endpoint is not up (e.g. immediately
when the endpoint receives ACTIVATE_MSG, the network interface goes
down...).
This is a normal situation and will be settled because the link
endpoint will be eventually brought down after the link tolerance time.
However, the situation will become worse when the second link is
established before the first link endpoint goes down,
For example:
1. Both links <1A-2A>, <1B-2B> down
2. Link endpoint 2A up, but 1A still down (e.g. due to network
disturbance, wrong session, etc.)
3. Link <1B-2B> up
4. Link endpoint 2A down (e.g. due to link tolerance timeout)
5. Node B starts failover onto link <1B-2B>
==> Node A does never start link failover.
When the "half-failover" situation happens, two consequences have been
observed:
a) Peer link/node gets stuck in FAILINGOVER state;
b) Traffic or user messages that peer node is trying to failover onto
the second link can be partially or completely dropped by this node.
The consequence a) was actually solved by commit
c140eb166d68 ("tipc:
fix failover problem"), but that commit didn't cover the b). It's due
to the fact that the tunnel link endpoint has never been prepared for a
failover, so the 'l->drop_point' (and the other data...) is not set
correctly. When a TUNNEL_MSG from peer node arrives on the link,
depending on the inner message's seqno and the current 'l->drop_point'
value, the message can be dropped (- treated as a duplicate message) or
processed.
At this early stage, the traffic messages from peer are likely to be
NAME_DISTRIBUTORs, this means some name table entries will be missed on
the node forever!
The commit resolves the issue by starting the FAILOVER process on this
node as well. Another benefit from this solution is that we ensure the
link will not be re-established until the failover ends.
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Wed, 1 May 2019 20:14:21 +0000 (22:14 +0200)]
net: phy: improve resuming from hibernation
I got an interesting report [0] that after resuming from hibernation
the link has 100Mbps instead of 1Gbps. Reason is that another OS has
been used whilst Linux was hibernated. And this OS speeds down the link
due to WoL. Therefore, when resuming, we shouldn't expect that what
the PHY advertises is what it did when hibernating.
Easiest way to do this is removing state PHY_RESUMING. Instead always
go via PHY_UP that configures PHY advertisement.
[0] https://bugzilla.kernel.org/show_bug.cgi?id=202851
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Wed, 1 May 2019 19:34:43 +0000 (21:34 +0200)]
net: phy: improve pause handling
When probing the phy device we set sym and asym pause in the "supported"
bitmap (unless the PHY tells us otherwise). However we don't know yet
whether the MAC supports pause. Simply copying phy->supported to
phy->advertising will trigger advertising pause, and that's not
what we want. Therefore add phy_advertise_supported() that copies all
modes but doesn't touch the pause bits.
In phy_support_(a)sym_pause we shouldn't set any bits in the supported
bitmap because we may set a bit the PHY intentionally disabled.
Effective pause support should be the AND-combined PHY and MAC pause
capabilities. If the MAC supports everything, then it's only relevant
what the PHY supports. If MAC supports sym pause only, then we have to
clear the asym bit in phydev->supported.
Copy the pause flags only and don't touch the modes, because a driver
may have intentionally removed a mode from phydev->advertising.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gustavo A. R. Silva [Wed, 1 May 2019 16:23:15 +0000 (11:23 -0500)]
net: sched: cls_u32: use struct_size() helper
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes, in particular in the
context in which this code is being used.
So, replace code of the following form:
sizeof(*s) + s->nkeys*sizeof(struct tc_u32_key)
with:
struct_size(s, keys, s->nkeys)
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang [Thu, 2 May 2019 02:56:59 +0000 (19:56 -0700)]
net: add a generic tracepoint for TX queue timeout
Although devlink health report does a nice job on reporting TX
timeout and other NIC errors, unfortunately it requires drivers
to support it but currently only mlx5 has implemented it.
Before other drivers could catch up, it is useful to have a
generic tracepoint to monitor this kind of TX timeout. We have
been suffering TX timeout with different drivers, we plan to
start to monitor it with rasdaemon which just needs a new tracepoint.
Sample output:
ksoftirqd/1-16 [001] ..s2 144.043173: net_dev_xmit_timeout: dev=ens3 driver=e1000 queue=0
Cc: Eran Ben Elisha <eranbe@mellanox.com>
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 4 May 2019 04:25:02 +0000 (00:25 -0400)]
Merge tag 'mlx5-updates-2019-04-30' of git://git./linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2019-04-30
mlx5 misc updates:
1) Bodong Wang and Parav Pandit (6):
- Remove unused mlx5_query_nic_vport_vlans
- vport macros refactoring
- Fix vport access in E-Switch
- Use atomic rep state to serialize state change
2) Eli Britstein (2):
- prio tag mode support, added ACLs and replace TC vlan pop with
vlan 0 rewrite when prio tag mode is enabled.
3) Erez Alfasi (2):
- ethtool: Add SFF-8436 and SFF-8636 max EEPROM length definitions
- mlx5e: ethtool, Add support for EEPROM high pages query
4) Masahiro Yamada (1):
- remove meaningless CFLAGS_tracepoint.o
5) Maxim Mikityanskiy (1):
- Put the common XDP code into a function
6) Tariq Toukan (2):
- Turn on HW tunnel offload in all TIRs
7) Vlad Buslov (1):
- Return error when trying to insert existing flower filter
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 4 May 2019 04:20:52 +0000 (00:20 -0400)]
Merge branch '100GbE' of git://git./linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2019-05-02
This series contains updates to the ice driver only.
Anirudh introduces the framework to store queue specific information in
the VSI queue contexts. This will allow future changes to update the
structure to hold queue specific information.
Akeem adds additional check so that if there is no queue to disable when
attempting to disable a queue, return a configuration error without
acquiring the lock. Fixed an issue with non-trusted VFs being able to
add more than the permitted number of VLANs.
Bruce removes unreachable code and updated the function to return void
since it would never return anything but success.
Brett provides most of the changes in the series, starting with reducing
the scope of the error variable used and improved the debug message if
we fail to configure the receive queue. Updates the driver to use a
macro instead of using the same 'for' loop throughout the driver which
helps with readability. Fixed an issue where users were led to believe
they could set rx-usecs-high value, yet the changes to this value would
not stick because it was not yet implemented to allow changes to this
value, so implement the missing code to change the value. Found we had
unnecessary wait when disabling queues, so remove it. I,proved a
wasteful addition operation in our hot path by adding a member to the
ice_q_vector structure and the necessary changes to use the member which
stores the calculated vector hardware index. Refactored the link event
flow to make it cleaner and more clear.
Maciej updates the array index when stopping transmit rings, so that
process every ring the VSI, not just the rings in a given transmit
class.
Paul adds support for setting 52 byte RSS hash keys.
Md Fahad cleaned up a runtime change to the PFINT_OICR_ENA register,
since the interrupt handlers will handle resetting the bit, if
necessary.
Tony adds a missing PHY type, which was causing warning message about an
unrecognized PHY.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Gustavo A. R. Silva [Wed, 1 May 2019 03:27:32 +0000 (22:27 -0500)]
wimax/i2400m: use struct_size() helper
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes, in particular in the
context in which this code is being used.
So, replace code of the following form:
sizeof(*tx_msg) + le16_to_cpu(tx_msg->num_pls) * sizeof(tx_msg->pld[0]);
with:
struct_size(tx_msg, pld, le16_to_cpu(tx_msg->num_pls));
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 4 May 2019 04:02:41 +0000 (00:02 -0400)]
Merge branch 'net-hns3-enhance-capabilities-for-fibre-port'
Jian Shen says:
====================
net: hns3: enhance capabilities for fibre port
This patchset enhances more capabilities for fibre port,
include multipe media type identification, autoneg,
change port speed and FEC encoding.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jian Shen [Fri, 3 May 2019 09:50:39 +0000 (17:50 +0800)]
net: hns3: add support for FEC encoding control
This patch adds support for FEC encoding control, user can change
FEC mode by command ethtool --set-fec, and get FEC mode by command
ethtool --show-fec. The fec capability is changed follow the port
speed. If autoneg on, the user configure fec mode will be overwritten
by autoneg result.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jian Shen [Fri, 3 May 2019 09:50:38 +0000 (17:50 +0800)]
net: hns3: add autoneg and change speed support for fibre port
Previously, our driver only supports phydev to autoneg or change
port speed. This patch adds support for fibre port, driver gets
media speed capability and autoneg capability from firmware. If
the media supports multiple speeds, user can change port speed
with command "ethtool -s <devname> speed xxxx autoneg off duplex
full". If autoneg on, the user configuration may be overwritten
by the autoneg result.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jian Shen [Fri, 3 May 2019 09:50:37 +0000 (17:50 +0800)]
net: hns3: add support for multiple media type
Previously, we can only identify copper and fiber type, the
supported link modes of port information are always showing
SR type. This patch adds support for multiple media types,
include SR, LR CR, KR. Driver needs to query the media type
from firmware periodicly, and updates the port information.
The new port information looks like this:
Settings for eth0:
Supported ports: [ FIBRE ]
Supported link modes: 25000baseCR/Full
25000baseSR/Full
1000baseX/Full
10000baseCR/Full
10000baseSR/Full
10000baseLR/Full
Supported pause frame use: Symmetric
Supports auto-negotiation: No
Supported FEC modes: None BaseR
Advertised link modes: Not reported
Advertised pause frame use: No
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Speed: 10000Mb/s
Duplex: Full
Port: FIBRE
PHYAD: 0
Transceiver: internal
Auto-negotiation: off
Current message level: 0x00000036 (54)
probe link ifdown ifup
Link detected: yes
In order to be compatible with old firmware which only support
sfp speed, we remained using the same query command, and kept
the former logic.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Guenter Roeck [Wed, 1 May 2019 00:35:33 +0000 (17:35 -0700)]
usbnet: ipheth: Remove unnecessary NULL pointer check
ipheth_carrier_set() is called from two locations. In
ipheth_carrier_check_work(), its parameter 'dev' is set with
container_of(work, ...) and can not be NULL. In ipheth_open(),
dev is extracted from netdev_priv(net) and dereferenced before
the call to ipheth_carrier_set(). The NULL pointer check of dev
in ipheth_carrier_set() is therefore unnecessary and can be removed.
Cc: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Tue, 30 Apr 2019 22:10:50 +0000 (00:10 +0200)]
net: dsa: mv88e6xxx: Pass interrupt number in platform data
Allow an interrupt number to be passed in the platform data. The
driver will then use it if not zero, otherwise it will poll for
interrupts.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 4 May 2019 03:53:06 +0000 (23:53 -0400)]
Merge branch 'mv88e6xxx-Disable-ports-to-save-power'
Andrew Lunn says:
====================
mv88e6xxx: Disable ports to save power
Save some power by disabling ports. The first patch fully disables a
port when it is runtime disabled. The second disables any ports which
are not used at all.
Depending on configuration strapping, this can lower the temperature
of an idle switch a few degrees.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Tue, 30 Apr 2019 22:08:31 +0000 (00:08 +0200)]
net: dsa :mv88e6xxx: Disable unused ports
If the NO_CPU strap is set, the switch starts in 'dumb hub' mode, with
all ports enable. Ports which are then actively used are reconfigured
as required when the driver starts. However unused ports are left
alone. Change this to disable them, and turn off any SERDES
interface. This could save some power and so reduce the temperature a
bit.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrew Lunn [Tue, 30 Apr 2019 22:08:30 +0000 (00:08 +0200)]
net: dsa: mv88e6xxx: Set STP disable state in port_disable
When requested to disable a port, set the port STP state to disabled.
This fully disables the port and should save some power.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 4 May 2019 03:27:00 +0000 (23:27 -0400)]
Merge branch '40GbE' of git://git./linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2019-05-03
This series contains updates to the i40e driver only.
Carolyn changes the driver behavior to now disable the VF after one MDD
event instead of allowing a couple of MDD events before doing the reset.
Aleksandr changes the driver to only report an error when a VF tries to
remove VLAN when a port VLAN is configured, unless it is VLAN 0. Also
extends the LLDP support to be able to keep the current LLDP state
persistent across a power cycle.
Maciej fixes the checksum calculation due to firmware changes, which
requires the driver to perform a double shadow RAM dump in some cases.
Adam adds advertising support for 40GBase_LR4, 40GBase_CR4 and fibre in
the driver.
Jake cleans up a check that is not needed and was producing a warning in
GCC 8.
Harshitha fixes a misleading message by ensuring that a success message
is only printed on the host side when the promiscuous mode change has
been successful.
Stefan Assmann adds the vendor id and device id to the dmesg log entry
during probe to help with bug reports when lspci output may not be
available.
Alice and Piotr add recovery mode support in the i40e driver, which is
needed for migrating from a structured to a flat firmware image.
v2: Removed patch 1 "i40e: replace switch-statement to speed-up
retpoline-enabled builds" from the series since it is no longer
needed. Also updated the last patch in the series that introduces
recovery mode support, to include a more detailed patch description
and removed code not intended for the upstream kernel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Alice Michael [Fri, 3 May 2019 00:01:53 +0000 (17:01 -0700)]
i40e: Introduce recovery mode support
This patch introduces "recovery mode" to the i40e driver. It is
part of a new Any2Any idea of upgrading the firmware. In this
approach, it is required for the driver to have support for
"transition firmware", that is used for migrating from structured
to flat firmware image. In this new, very basic mode, i40e driver
must be able to handle particular IOCTL calls from the NVM Update
Tool and run a small set of AQ commands.
These additional AQ commands are part of the interface used by
the NVMUpdate tool. The NVMUpdate tool contains all of the
necessary logic to reference these new AQ commands. The end user
experience remains the same, they are using the NVMUpdate tool to
update the NVM contents.
Signed-off-by: Alice Michael <alice.michael@intel.com>
Signed-off-by: Piotr Marczak <piotr.marczak@intel.com>
Tested-by: Don Buchholz <donald.buchholz@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Stefan Assmann [Tue, 12 Mar 2019 11:18:02 +0000 (12:18 +0100)]
i40e: print PCI vendor and device ID during probe
Printing each devices PCI vendor and device ID has the advantage of
easily revealing what hardware we're dealing with exactly. It's no
longer necessary to match the PCI bus information to the lspci output.
Helps with bug reports where no lspci output is available.
Output before
i40e 0000:08:00.0: fw 6.1.49420 api 1.7 nvm 6.80 0x80003c64 1.2007.0
and after
i40e 0000:08:00.0: fw 6.1.49420 api 1.7 nvm 6.80 0x80003c64 1.2007.0 [8086:1572] [8086:0004]
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Harshitha Ramamurthy [Thu, 28 Feb 2019 17:52:55 +0000 (09:52 -0800)]
i40e: fix misleading message about promisc setting on un-trusted VF
A refactor of the i40e_vc_config_promiscuous_mode_msg function moved
the check for un-trusted VF into another function. We have to lie to
an un-trusted VF that its request to set promiscuous mode is
successful even when it is not because we don't want the VF to find
out its trust status this way. With the refactor, we were running into
a case where even though we were not setting promiscuous mode for an
un-trusted VF, we still printed a misleading message that it was
successful.
This patch fixes that by ensuring that a success message is printed
on the host side only when the promiscuous mode change has been
successful.
Signed-off-by: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alice Michael [Thu, 28 Feb 2019 17:52:54 +0000 (09:52 -0800)]
i40e: update version number
Just bumping the version number appropriately.
Signed-off-by: Alice Michael <alice.michael@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jacob Keller [Thu, 28 Feb 2019 17:52:53 +0000 (09:52 -0800)]
i40e: remove out-of-range comparisons in i40e_validate_cloud_filter
The function i40e_validate_cloud_filter checks that the destination and
source port numbers are valid by attempting to ensure that the number is
non-zero and no larger than 0xFFFF. However, the types for the dst_port
and src_port variable are __be16 which by definition cannot be larger
than 0xFFFF
Since these values cannot be larger than 2 bytes, the check to see if
they exceed 0xFFFF is meaningless.
One might consider these checks as some sort of defensive coding, in
case the type was later changed. However, these checks also byte-swap
the value before comparison using be16_to_cpu, which will truncate the
values to 16bits anyways. Additionally, changing the type would require
updating the opcodes to support new data layout of these virtchnl
commands.
Remove the check to silence the -Wtype-limits warning that was added to
GCC 8.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Aleksandr Loktionov [Thu, 28 Feb 2019 17:52:52 +0000 (09:52 -0800)]
i40e: Further implementation of LLDP
This code implements driver code changes necessary for LLDP
Agent support. Modified i40e_aq_start_lldp() and
i40e_aq_stop_lldp() adding false parameter whether LLDP state
should be persistent across power cycles.
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Adam Ludkiewicz [Thu, 28 Feb 2019 17:52:51 +0000 (09:52 -0800)]
i40e: Report advertised link modes on 40GBase_LR4, CR4 and fibre
Add assignments for advertising 40GBase_LR4, 40GBase_CR4 and fibre
Signed-off-by: Adam Ludkiewicz <adam.ludkiewicz@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Maciej Paczkowski [Thu, 28 Feb 2019 17:52:50 +0000 (09:52 -0800)]
i40e: ShadowRAM checksum calculation change
Due to changes in FW the SW is required to perform double SR dump in
some cases.
Implementation adds two new steps to update nvm checksum function:
* recalculate checksum and check if checksum in NVM is correct
* if checksum in NVM is not correct then update it again
Signed-off-by: Maciej Paczkowski <maciej.paczkowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Aleksandr Loktionov [Thu, 28 Feb 2019 17:52:49 +0000 (09:52 -0800)]
i40e: remove error msg when vf with port vlan tries to remove vlan 0
VF's attempt to delete vlan 0 when a port vlan is configured is harmless
in this case pf driver just does nothing. If vf will try to remove
other vlans when a port vlan is configured it will still produce error
as before.
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Carolyn Wyborny [Thu, 28 Feb 2019 17:52:48 +0000 (09:52 -0800)]
i40e: change behavior on PF in response to MDD event
TX MDD events reported on the PF are the result of the
PF misconfiguring a descriptor and not because of "bad actions"
by anything else. No need to reset now because if it
results in a Tx hang, the Tx hang check will take care of it.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Carolyn Wyborny [Thu, 28 Feb 2019 17:52:47 +0000 (09:52 -0800)]
i40e: Fix for allowing too many MDD events on VF
This patch changes the driver behavior when detecting a VF MDD event.
It now disables the VF after one event, which indicates a hw detected
problem in the VF. Before this change, the PF would allow a couple of
events before doing the reset.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
David S. Miller [Fri, 3 May 2019 14:49:18 +0000 (10:49 -0400)]
Merge branch 'NXP-SJA1105-DSA-driver'
Vladimir Oltean says:
====================
NXP SJA1105 DSA driver
This patchset adds a DSA driver for the SPI-controlled NXP SJA1105
switch. Due to the hardware's unfriendliness, most of its state needs
to be shadowed in kernel memory by the driver. To support this and keep
a decent amount of cleanliness in the code, a new generic API for
converting between CPU-accessible ("unpacked") structures and
hardware-accessible ("packed") structures is proposed and used.
The driver is GPL-2.0 licensed. The source code files which are licensed
as BSD-3-Clause are hardware support files and derivative of the
userspace NXP sja1105-tool program, which is BSD-3-Clause licensed.
TODO items:
* Add support for traffic.
* Add full support for the P/Q/R/S series. The patches were mostly
tested on a first-generation T device.
* Add timestamping support and PTP clock manipulation.
* Figure out how the tc-taprio hardware offload that was just proposed
by Vinicius can be used to configure the switch's time-aware scheduler.
* Rework link state callbacks to use phylink once the SGMII port
is supported.
Changes in v5:
1. Removed trailing empty lines at the end of files.
2. Moved the lib/packing.c file under a CONFIG_PACKING option instead of
having it always built-in. The module is GPL licensed, which applies
to its distribution in binary form, but the code is dual-licensed
which means it can be used in projects with other licenses as well.
3. Made SJA1105 driver select CONFIG_PACKING and CONFIG_CRC32.
v4 patchset can be found at:
https://lwn.net/Articles/787077/
Changes in v4:
1. Previous patchset was broken apart, and for the moment the driver is
configuring the switch as unmanaged. Support for regular and management
traffic, as well as for PTP timestamping, will be submitted once the
basic driver is accepted. Some core DSA patches were also broken out
of the series, and are a dependency for this series:
https://patchwork.ozlabs.org/project/netdev/list/?series=105069
2. Addressed Jiri Pirko's feedback about too generic function and macro
naming.
3. Re-introduced ETH_P_DSA_8021Q.
v3 patchset can be found at:
https://lkml.org/lkml/2019/4/12/978
Changes in v3:
1. Removed the patch for a dedicated Ethertype to use with 802.1Q DSA
tagging
2. Changed the SJA1105 switch tagging protocol sysfs label from
"sja1105" to "8021q" to denote to users such as tcpdump that the
structure is more generic.
3. Respun previous patch "net: dsa: Allow drivers to modulate between
presence and absence of tagging". Current equivalent patch is called
"net: dsa: Allow drivers to filter packets they can decode source
port from" and at least allows reception of management traffic during
the time when switch tagging is not enabled.
4. Added DSA-level fixes for the bridge core not unsetting
vlan_filtering when ports leave. The global VLAN filtering is treated
as a special case. Made the mt7530 driver use this. This patch
benefits the SJA1105 because otherwise traffic in standalone mode
would no longer work after removing the ports from a vlan_filtering
bridge, since the driver and the hardware would be in an inconsistent
state.
5. Restructured the documentation as rst. This depends upon the recently
submitted "[PATCH net-next] Documentation: net: dsa: transition to
the rst format": https://patchwork.ozlabs.org/patch/
1084658/.
v2 patchset can be found at:
https://www.spinics.net/lists/netdev/msg563454.html
Changes in v2:
1. Device ID is no longer auto-detected but enforced based on explicit DT
compatible string. This helps with stricter checking of DT bindings.
2. Group all device-specific operations into a sja1105_info structure and
avoid using the IS_ET() and IS_PQRS() macros at runtime as much as possible.
3. Added more verbiage to commit messages and documentation.
4. Treat the case where RGMII internal delays are requested through DT bindings
and return error.
5. Miscellaneous cosmetic cleanup in sja1105_clocking.c
6. Not advertising link features that are not supported, such as pause frames
and the half duplex modes.
7. Fixed a mistake in previous patchset where the switch tagging was not
actually enabled (lost during a rebase). This brought up another uncaught
issue where switching at runtime between tagging and no-tagging was not
supported by DSA. Fixed up the mistake in "net: dsa: sja1105: Add support
for traffic through standalone ports", and added the new patch "net: dsa:
Allow drivers to modulate between presence and absence of tagging" to
address the other issue.
8. Added a workaround for switch resets cutting a frame in the middle of
transmission, which would throw off some link partners.
9. Changed the TPID from ETH_P_EDSA (0xDADA) to a newly introduced one:
ETH_P_DSA_8021Q (0xDADB). Uncovered another mistake in the previous patchset
with a missing ntohs(), which was not caught because 0xDADA is
endian-agnostic.
10. Made NET_DSA_TAG_8021Q select VLAN_8021Q
11. Renamed __dsa_port_vlan_add to dsa_port_vid_add and not to
dsa_port_vlan_add_trans, as suggested, because the corresponding _del function
does not have a transactional phase and the naming is more uniform this way.
v1 patchset can be found at:
https://www.spinics.net/lists/netdev/msg561589.html
Changes from RFC:
1. Removed the packing code for the static configuration tables that were
not currently used
2. Removed the code for unpacking a static configuration structure from
a memory buffer (not used)
3. Completely removed the SGMII stubs, since the configuration is not
complete anyway.
4. Moved some code from the SJA1105 introduction commit into the patch
that used it.
5. Made the code for checking global VLAN filtering generic and made b53
driver use it.
6. Made mt7530 driver use the new generic dp->vlan_filtering
7. Fixed check for stringset in .get_sset_count
8. Minor cleanup in sja1105_clocking.c
9. Fixed a confusing typo in DSA
RFC can be found at:
https://www.mail-archive.com/netdev@vger.kernel.org/msg291717.html
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Thu, 2 May 2019 20:23:40 +0000 (23:23 +0300)]
dt-bindings: net: dsa: Add documentation for NXP SJA1105 driver
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Thu, 2 May 2019 20:23:39 +0000 (23:23 +0300)]
Documentation: net: dsa: Add details about NXP SJA1105 driver
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Thu, 2 May 2019 20:23:38 +0000 (23:23 +0300)]
net: dsa: sja1105: Reject unsupported link modes for AN
Ethernet flow control:
The switch MAC does not consume, nor does it emit pause frames. It
simply forwards them as any other Ethernet frame (and since the DMAC is,
per IEEE spec, 01-80-C2-00-00-01, it means they are filtered as
link-local traffic and forwarded to the CPU, which can't do anything
useful with them).
Duplex:
There is no duplex setting in the SJA1105 MAC. It is known to forward
traffic at line rate on the same port in both directions. Therefore it
must be that it only supports full duplex.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Thu, 2 May 2019 20:23:37 +0000 (23:23 +0300)]
net: dsa: sja1105: Prevent PHY jabbering during switch reset
Resetting the switch at runtime is currently done while changing the
vlan_filtering setting (due to the required TPID change).
But reset is asynchronous with packet egress, and the switch core will
not wait for egress to finish before carrying on with the reset
operation.
As a result, a connected PHY such as the BCM5464 would see an
unterminated Ethernet frame and start to jabber (repeat the last seen
Ethernet symbols - jabber is by definition an oversized Ethernet frame
with bad FCS). This behavior is strange in itself, but it also causes
the MACs of some link partners (such as the FRDM-LS1012A) to completely
lock up.
So as a remedy for this situation, when switch reset is required, simply
inhibit Tx on all ports, and wait for the necessary time for the
eventual one frame left in the egress queue (not even the Tx inhibit
command is instantaneous) to be flushed.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Thu, 2 May 2019 20:23:36 +0000 (23:23 +0300)]
net: dsa: sja1105: Add support for configuring address ageing time
If STP is active, this setting is applied on bridged ports each time an
Ethernet link is established (topology changes).
Since the setting is global to the switch and a reset is required to
change it, resets are prevented if the new callback does not change the
value that the hardware already is programmed for.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Thu, 2 May 2019 20:23:35 +0000 (23:23 +0300)]
net: dsa: sja1105: Add support for ethtool port counters
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Thu, 2 May 2019 20:23:34 +0000 (23:23 +0300)]
net: dsa: sja1105: Add support for VLAN operations
VLAN filtering cannot be properly disabled in SJA1105. So in order to
emulate the "no VLAN awareness" behavior (not dropping traffic that is
tagged with a VID that isn't configured on the port), we need to hack
another switch feature: programmable TPID (which is 0x8100 for 802.1Q).
We are reprogramming the TPID to a bogus value which leaves the switch
thinking that all traffic is untagged, and therefore accepts it.
Under a vlan_filtering bridge, the proper TPID of ETH_P_8021Q is
installed again, and the switch starts identifying 802.1Q-tagged
traffic.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Thu, 2 May 2019 20:23:33 +0000 (23:23 +0300)]
ether: Add dedicated Ethertype for pseudo-802.1Q DSA tagging
There are two possible utilizations so far:
- Switch devices that don't support a native insertion/extraction header
on the CPU port may still enjoy the benefits of port isolation with a
custom VLAN tag.
For this, they need to have a customizable TPID in hardware and a new
Ethertype to distinguish between real 802.1Q traffic and the private
tags used for port separation.
- Switches that don't support the deactivation of VLAN awareness, but
still want to have a mode in which they accept all traffic, including
frames that are tagged with a VLAN not configured on their ports, may
use this as a fake to trick the hardware into thinking that the TPID
for VLAN is something other than 0x8100.
What follows after the ETH_P_DSA_8021Q EtherType is a regular VLAN
header (TCI), however there is no other EtherType that can be used for
this purpose and doesn't already have a well-defined meaning.
ETH_P_8021AD, ETH_P_QINQ1, ETH_P_QINQ2 and ETH_P_QINQ3 expect that
another follow-up VLAN tag is present, which is not the case here.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Thu, 2 May 2019 20:23:32 +0000 (23:23 +0300)]
net: dsa: sja1105: Error out if RGMII delays are requested in DT
Documentation/devicetree/bindings/net/ethernet.txt is confusing because
it says what the MAC should not do, but not what it *should* do:
* "rgmii-rxid" (RGMII with internal RX delay provided by the PHY, the MAC
should not add an RX delay in this case)
The gap in semantics is threefold:
1. Is it illegal for the MAC to apply the Rx internal delay by itself,
and simplify the phy_mode (mask off "rgmii-rxid" into "rgmii") before
passing it to of_phy_connect? The documentation would suggest yes.
1. For "rgmii-rxid", while the situation with the Rx clock skew is more
or less clear (needs to be added by the PHY), what should the MAC
driver do about the Tx delays? Is it an implicit wild card for the
MAC to apply delays in the Tx direction if it can? What if those were
already added as serpentine PCB traces, how could that be made more
obvious through DT bindings so that the MAC doesn't attempt to add
them twice and again potentially break the link?
3. If the interface is a fixed-link and therefore the PHY object is
fixed (a purely software entity that obviously cannot add clock
skew), what is the meaning of the above property?
So an interpretation of the RGMII bindings was chosen that hopefully
does not contradict their intention but also makes them more applied.
The SJA1105 driver understands to act upon "rgmii-*id" phy-mode bindings
if the port is in the PHY role (either explicitly, or if it is a
fixed-link). Otherwise it always passes the duty of setting up delays to
the PHY driver.
The error behavior that this patch adds is required on SJA1105E/T where
the MAC really cannot apply internal delays. If the other end of the
fixed-link cannot apply RGMII delays either (this would be specified
through its own DT bindings), then the situation requires PCB delays.
For SJA1105P/Q/R/S, this is however hardware supported and the error is
thus only temporary. I created a stub function pointer for configuring
delays per-port on RXC and TXC, and will implement it when I have access
to a board with this hardware setup.
Meanwhile do not allow the user to select an invalid configuration.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Thu, 2 May 2019 20:23:31 +0000 (23:23 +0300)]
net: dsa: sja1105: Add support for FDB and MDB management
Currently only the (more difficult) first generation E/T series is
supported. Here the TCAM is only 4-way associative, and to know where
the hardware will search for a FDB entry, we need to perform the same
hash algorithm in order to install the entry in the correct bin.
On P/Q/R/S, the TCAM should be fully associative. However the SPI
command interface is different, and because I don't have access to a
new-generation device at the moment, support for it is TODO.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Thu, 2 May 2019 20:23:30 +0000 (23:23 +0300)]
net: dsa: Introduce driver for NXP SJA1105 5-port L2 switch
At this moment the following is supported:
* Link state management through phylib
* Autonomous L2 forwarding managed through iproute2 bridge commands.
IP termination must be done currently through the master netdevice,
since the switch is unmanaged at this point and using
DSA_TAG_PROTO_NONE.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Georg Waibel <georg.waibel@sensor-technik.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Thu, 2 May 2019 20:23:29 +0000 (23:23 +0300)]
lib: Add support for generic packing operations
This provides an unified API for accessing register bit fields
regardless of memory layout. The basic unit of data for these API
functions is the u64. The process of transforming an u64 from native CPU
encoding into the peripheral's encoding is called 'pack', and
transforming it from peripheral to native CPU encoding is 'unpack'.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Ferre [Fri, 3 May 2019 10:36:58 +0000 (12:36 +0200)]
net: macb: shrink macb_platform_data structure
This structure was used intensively for machine specific values
when DT was not used. Since the removal of AVR32 from the kernel,
this structure is only used for passing clocks from PCI macb wrapper, all
other fields being 0.
All other known platforms use DT.
Remove the leftovers but make sure that PCI macb still works as
expected by using default values:
- phydev->irq is set to PHY_POLL by mdiobus_alloc()
- mii_bus->phy_mask is cleared while allocating it
- bp->phy_interface is set to PHY_INTERFACE_MODE_MII if mode not found
in DT.
This simplifies driver probe path and particularly phy handling.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Ferre [Fri, 3 May 2019 10:36:28 +0000 (12:36 +0200)]
net: macb: remove redundant struct phy_device declaration
While moving the chunk of code during
739de9a1563a
("net: macb: Reorganize macb_mii bringup"), the declaration of
struct phy_device declaration was kept. It's not useful in this
function as we alrady have a phydev pointer.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 3 May 2019 02:14:21 +0000 (22:14 -0400)]
Merge git://git./linux/kernel/git/davem/net
Three trivial overlapping conflicts.
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Thu, 2 May 2019 18:03:34 +0000 (11:03 -0700)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
1) Out of bounds access in xfrm IPSEC policy unlink, from Yue Haibing.
2) Missing length check for esp4 UDP encap, from Sabrina Dubroca.
3) Fix byte order of RX STBC access in mac80211, from Johannes Berg.
4) Inifnite loop in bpftool map create, from Alban Crequy.
5) Register mark fix in ebpf verifier after pkt/null checks, from Paul
Chaignon.
6) Properly use rcu_dereference_sk_user_data in L2TP code, from Eric
Dumazet.
7) Buffer overrun in marvell phy driver, from Andrew Lunn.
8) Several crash and statistics handling fixes to bnxt_en driver, from
Michael Chan and Vasundhara Volam.
9) Several fixes to the TLS layer from Jakub Kicinski (copying negative
amounts of data in reencrypt, reencrypt frag copying, blind nskb->sk
NULL deref, etc).
10) Several UDP GRO fixes, from Paolo Abeni and Eric Dumazet.
11) PID/UID checks on ipv6 flow labels are inverted, from Willem de
Bruijn.
12) Use after free in l2tp, from Eric Dumazet.
13) IPV6 route destroy races, also from Eric Dumazet.
14) SCTP state machine can erroneously run recursively, fix from Xin
Long.
15) Adjust AF_PACKET msg_name length checks, add padding bytes if
necessary. From Willem de Bruijn.
16) Preserve skb_iif, so that forwarded packets have consistent values
even if fragmentation is involved. From Shmulik Ladkani.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (69 commits)
udp: fix GRO packet of death
ipv6: A few fixes on dereferencing rt->from
rds: ib: force endiannes annotation
selftests: fib_rule_tests: print the result and return 1 if any tests failed
ipv4: ip_do_fragment: Preserve skb_iif during fragmentation
net/tls: avoid NULL pointer deref on nskb->sk in fallback
selftests: fib_rule_tests: Fix icmp proto with ipv6
packet: validate msg_namelen in send directly
packet: in recvmsg msg_name return at least sizeof sockaddr_ll
sctp: avoid running the sctp state machine recursively
stmmac: pci: Fix typo in IOT2000 comment
Documentation: fix netdev-FAQ.rst markup warning
ipv6: fix races in ip6_dst_destroy()
l2ip: fix possible use-after-free
appletalk: Set error code if register_snap_client failed
net: dsa: bcm_sf2: fix buffer overflow doing set_rxnfc
rxrpc: Fix net namespace cleanup
ipv6/flowlabel: wait rcu grace period before put_pid()
vrf: Use orig netdev to count Ip6InNoRoutes and a fresh route lookup when sending dest unreach
tcp: add sanity tests in tcp_add_backlog()
...
Linus Torvalds [Thu, 2 May 2019 16:55:04 +0000 (09:55 -0700)]
Merge tag 'for-linus-
20190502' of git://git.kernel.dk/linux-block
Pull io_uring fixes from Jens Axboe:
"This is mostly io_uring fixes/tweaks. Most of these were actually done
in time for the last -rc, but I wanted to ensure that everything
tested out great before including them. The code delta looks larger
than it really is, as it's mostly just comment additions/changes.
Outside of the comment additions/changes, this is mostly removal of
unnecessary barriers. In all, this pull request contains:
- Tweak to how we handle errors at submission time. We now post a
completion event if the error occurs on behalf of an sqe, instead
of returning it through the system call. If the error happens
outside of a specific sqe, we return the error through the system
call. This makes it nicer to use and makes the "normal" use case
behave the same as the offload cases. (me)
- Fix for a missing req reference drop from async context (me)
- If an sqe is submitted with RWF_NOWAIT, don't punt it to async
context. Return -EAGAIN directly, instead of using it as a hint to
do async punt. (Stefan)
- Fix notes on barriers (Stefan)
- Remove unnecessary barriers (Stefan)
- Fix potential double free of memory in setup error (Mark)
- Further improve sq poll CPU validation (Mark)
- Fix page allocation warning and leak on buffer registration error
(Mark)
- Fix iov_iter_type() for new no-ref flag (Ming)
- Fix a case where dio doesn't honor bio no-page-ref (Ming)"
* tag 'for-linus-
20190502' of git://git.kernel.dk/linux-block:
io_uring: avoid page allocation warnings
iov_iter: fix iov_iter_type
block: fix handling for BIO_NO_PAGE_REF
io_uring: drop req submit reference always in async punt
io_uring: free allocated io_memory once
io_uring: fix SQPOLL cpu validation
io_uring: have submission side sqe errors post a cqe
io_uring: remove unnecessary barrier after unsetting IORING_SQ_NEED_WAKEUP
io_uring: remove unnecessary barrier after incrementing dropped counter
io_uring: remove unnecessary barrier before reading SQ tail
io_uring: remove unnecessary barrier after updating SQ head
io_uring: remove unnecessary barrier before reading cq head
io_uring: remove unnecessary barrier before wq_has_sleeper
io_uring: fix notes on barriers
io_uring: fix handling SQEs requesting NOWAIT
Linus Torvalds [Thu, 2 May 2019 15:29:24 +0000 (08:29 -0700)]
Merge tag 'pci-v5.1-fixes-3' of git://git./linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"I apologize for sending these so late in the cycle. We went back and
forth about how to deal with the unexpected logging of intentional
link state changes and finally decided to just config them off by
default.
PCI fixes:
- Stop ignoring "pci=disable_acs_redir" parameter (Logan Gunthorpe)
- Use shared MSI/MSI-X vector for Link Bandwidth Management (Alex
Williamson)
- Add Kconfig option for Link Bandwidth notification messages (Keith
Busch)"
* tag 'pci-v5.1-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI/LINK: Add Kconfig option (default off)
PCI/portdrv: Use shared MSI/MSI-X vector for Bandwidth Management
PCI: Fix issue with "pci=disable_acs_redir" parameter being ignored
Linus Torvalds [Thu, 2 May 2019 15:27:39 +0000 (08:27 -0700)]
Merge tag 'mtd/fixes-for-5.1-rc6' of git://git./linux/kernel/git/mtd/linux
Pull MTD fix from Richard Weinberger:
"A single regression fix for the marvell nand driver"
* tag 'mtd/fixes-for-5.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
mtd: rawnand: marvell: Clean the controller state before each operation
Keith Busch [Wed, 1 May 2019 14:29:42 +0000 (08:29 -0600)]
PCI/LINK: Add Kconfig option (default off)
e8303bb7a75c ("PCI/LINK: Report degraded links via link bandwidth
notification") added dmesg logging whenever a link changes speed or width
to a state that is considered degraded. Unfortunately, it cannot
differentiate signal integrity-related link changes from those
intentionally initiated by an endpoint driver, including drivers that may
live in userspace or VMs when making use of vfio-pci. Some GPU drivers
actively manage the link state to save power, which generates a stream of
messages like this:
vfio-pci 0000:07:00.0: 32.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x16 link at 0000:00:02.0 (capable of 64.000 Gb/s with 5 GT/s x16 link)
Since we can't distinguish the intentional changes from the signal
integrity issues, leave the reporting turned off by default. Add a Kconfig
option to turn it on if desired.
Fixes:
e8303bb7a75c ("PCI/LINK: Report degraded links via link bandwidth notification")
Link: https://lore.kernel.org/linux-pci/20190501142942.26972-1-keith.busch@intel.com
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Esben Haabendal [Thu, 2 May 2019 06:43:43 +0000 (08:43 +0200)]
net: ll_temac: Fix typo bug for 32-bit
Fixes:
d84aec42151b ("net: ll_temac: Fix support for 64-bit platforms")
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Brett Creeley [Thu, 28 Feb 2019 23:26:02 +0000 (15:26 -0800)]
ice: Use dev_err when ice_cfg_vsi_lan fails
dev_err makes more sense than dev_info when this call fails.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Brett Creeley [Thu, 28 Feb 2019 23:26:01 +0000 (15:26 -0800)]
ice: Refactor link event flow
Currently the link event flow works, but can be much better.
Refactor the link event flow to make it cleaner and more clear
on what is going on.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tony Nguyen [Thu, 28 Feb 2019 23:26:00 +0000 (15:26 -0800)]
ice: Add missing PHY type to link settings
The PHY type ICE_PHY_TYPE_LOW_25G_AUI_C2C is missing from
ice_get_settings_link_up() which is causing a warning
message for unrecognized PHY. Add the PHY type to
correctly set the settings and avoid the warning message.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Brett Creeley [Thu, 28 Feb 2019 23:25:59 +0000 (15:25 -0800)]
ice: Add reg_idx variable in ice_q_vector structure
Every time we want to re-enable interrupts and/or write to a register
that requires an interrupt vector's hardware index we do the following:
vsi->hw_base_vector + q_vector->v_idx
This is a wasteful operation, especially in the hot path. Fix this by
adding a u16 reg_idx member to the ice_q_vector structure and make the
necessary changes to make this work.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Md Fahad Iqbal Polash [Thu, 28 Feb 2019 23:25:58 +0000 (15:25 -0800)]
ice: Remove runtime change of PFINT_OICR_ENA register
Runtime change of PFINT_OICR_ENA register is unnecessary.
The handlers should always clear the atomic bit for each
task as they start, because it will make sure that any late
interrupt will either 1) re-set the bit, or 2) be handled
directly in the "already running" task handler.
Signed-off-by: Md Fahad Iqbal Polash <md.fahad.iqbal.polash@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Akeem G Abodunrin [Thu, 28 Feb 2019 23:25:57 +0000 (15:25 -0800)]
ice: Fix issue when adding more than allowed VLANs
This patch fixes issue with non trusted VFs being able to add more than
permitted number of VLANs by adding a check in ice_vc_process_vlan_msg.
Also don't return an error in this case as the VF does not need to know
that it is not trusted.
Also rework ice_vsi_kill_vlan to use the right types.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Brett Creeley [Thu, 28 Feb 2019 23:25:56 +0000 (15:25 -0800)]
ice: Remove unnecessary wait when disabling/enabling Rx queues
In ice_vsi_ctrl_rx_rings() we are unnecessarily waiting for
QRX_CTRL_QENA_REQ and QRX_CTRL_QENA_STAT to be the same value prior to
disabling each Rx queue. There is no reason to do this so remove
this wait loop as we already have a wait loop after disabling/enabling
the Rx queue through the QRX_CTRL register to make sure it gets
successfully disabled/enabled.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Brett Creeley [Thu, 28 Feb 2019 23:25:55 +0000 (15:25 -0800)]
ice: Add ability to update rx-usecs-high
Currently the driver allows rx-usecs-high values to be set,
but when querying the device for rx-usecs-high the value
does not stick. This is because it was not yet implemented.
Add code to allow the user to change rx-usecs-high and
use this to set the q_vector's intrl value.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Paul Greenwalt [Thu, 28 Feb 2019 23:25:54 +0000 (15:25 -0800)]
ice: Add 52 byte RSS hash key support
Add support to set 52 byte RSS hash key.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Brett Creeley [Thu, 28 Feb 2019 23:25:53 +0000 (15:25 -0800)]
ice: Use ice_for_each_q_vector macro where possible
There are many places in the code where we do the following:
for (i = 0; i < vsi->num_q_vectors; i++)
Instead use the macro mentioned in the commit title:
ice_for_each_q_vector(vsi, i)
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Maciej Fijalkowski [Thu, 28 Feb 2019 23:25:52 +0000 (15:25 -0800)]
ice: Validate ring existence and its q_vector per VSI
When stopping Tx rings, we use 'i' as an ring array index for looking up
whether the ice_ring exists and have assigned a q_vector. This checks
rings only within a given TC and we need to go through every ring in
VSI. Use 'q_idx' instead.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Brett Creeley [Thu, 28 Feb 2019 23:25:51 +0000 (15:25 -0800)]
ice: Reduce scope of variable in ice_vsi_cfg_rxqs
Reduce scope of the variable 'err' to inside the for loop instead
of using it as a second looping conditional. Also while here,
improve the debug message if we fail to configure a Rx queue.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bruce Allan [Thu, 28 Feb 2019 23:25:50 +0000 (15:25 -0800)]
ice: Resolve static analysis reported issue
Static analysis points out the default case in the switch statement in
ice_get_itr_intrl_gran() is an infeasible condition causing the default
case statement to be unreachable. Remove it and since the function no
longer returns anything but success, change it to just return void and
update the only call to it accordingly.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Akeem G Abodunrin [Thu, 28 Feb 2019 23:25:49 +0000 (15:25 -0800)]
ice: Return configuration error without queue to disable
If there is no queue to disable, return appropriate configuration error
earlier without acquiring the lock.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Anirudh Venkataramanan [Thu, 28 Feb 2019 23:25:48 +0000 (15:25 -0800)]
ice: Create framework for VSI queue context
This patch introduces a framework to store queue specific information
in VSI queue contexts. Currently VSI queue context (represented by
struct ice_q_ctx) only has q_handle as a member. In future patches,
this structure will be updated to hold queue specific information.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Eric Dumazet [Thu, 2 May 2019 01:56:28 +0000 (18:56 -0700)]
udp: fix GRO packet of death
syzbot was able to crash host by sending UDP packets with a 0 payload.
TCP does not have this issue since we do not aggregate packets without
payload.
Since dev_gro_receive() sets gso_size based on skb_gro_len(skb)
it seems not worth trying to cope with padded packets.
BUG: KASAN: slab-out-of-bounds in skb_gro_receive+0xf5f/0x10e0 net/core/skbuff.c:3826
Read of size 16 at addr
ffff88808893fff0 by task syz-executor612/7889
CPU: 0 PID: 7889 Comm: syz-executor612 Not tainted 5.1.0-rc7+ #96
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x172/0x1f0 lib/dump_stack.c:113
print_address_description.cold+0x7c/0x20d mm/kasan/report.c:187
kasan_report.cold+0x1b/0x40 mm/kasan/report.c:317
__asan_report_load16_noabort+0x14/0x20 mm/kasan/generic_report.c:133
skb_gro_receive+0xf5f/0x10e0 net/core/skbuff.c:3826
udp_gro_receive_segment net/ipv4/udp_offload.c:382 [inline]
call_gro_receive include/linux/netdevice.h:2349 [inline]
udp_gro_receive+0xb61/0xfd0 net/ipv4/udp_offload.c:414
udp4_gro_receive+0x763/0xeb0 net/ipv4/udp_offload.c:478
inet_gro_receive+0xe72/0x1110 net/ipv4/af_inet.c:1510
dev_gro_receive+0x1cd0/0x23c0 net/core/dev.c:5581
napi_gro_frags+0x36b/0xd10 net/core/dev.c:5843
tun_get_user+0x2f24/0x3fb0 drivers/net/tun.c:1981
tun_chr_write_iter+0xbd/0x156 drivers/net/tun.c:2027
call_write_iter include/linux/fs.h:1866 [inline]
do_iter_readv_writev+0x5e1/0x8e0 fs/read_write.c:681
do_iter_write fs/read_write.c:957 [inline]
do_iter_write+0x184/0x610 fs/read_write.c:938
vfs_writev+0x1b3/0x2f0 fs/read_write.c:1002
do_writev+0x15e/0x370 fs/read_write.c:1037
__do_sys_writev fs/read_write.c:1110 [inline]
__se_sys_writev fs/read_write.c:1107 [inline]
__x64_sys_writev+0x75/0xb0 fs/read_write.c:1107
do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x441cc0
Code: 05 48 3d 01 f0 ff ff 0f 83 9d 09 fc ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 83 3d 51 93 29 00 00 75 14 b8 14 00 00 00 0f 05 <48> 3d 01 f0 ff ff 0f 83 74 09 fc ff c3 48 83 ec 08 e8 ba 2b 00 00
RSP: 002b:
00007ffe8c716118 EFLAGS:
00000246 ORIG_RAX:
0000000000000014
RAX:
ffffffffffffffda RBX:
00007ffe8c716150 RCX:
0000000000441cc0
RDX:
0000000000000001 RSI:
00007ffe8c716170 RDI:
00000000000000f0
RBP:
0000000000000000 R08:
000000000000ffff R09:
0000000000a64668
R10:
0000000020000040 R11:
0000000000000246 R12:
000000000000c2d9
R13:
0000000000402b50 R14:
0000000000000000 R15:
0000000000000000
Allocated by task 5143:
save_stack+0x45/0xd0 mm/kasan/common.c:75
set_track mm/kasan/common.c:87 [inline]
__kasan_kmalloc mm/kasan/common.c:497 [inline]
__kasan_kmalloc.constprop.0+0xcf/0xe0 mm/kasan/common.c:470
kasan_slab_alloc+0xf/0x20 mm/kasan/common.c:505
slab_post_alloc_hook mm/slab.h:437 [inline]
slab_alloc mm/slab.c:3393 [inline]
kmem_cache_alloc+0x11a/0x6f0 mm/slab.c:3555
mm_alloc+0x1d/0xd0 kernel/fork.c:1030
bprm_mm_init fs/exec.c:363 [inline]
__do_execve_file.isra.0+0xaa3/0x23f0 fs/exec.c:1791
do_execveat_common fs/exec.c:1865 [inline]
do_execve fs/exec.c:1882 [inline]
__do_sys_execve fs/exec.c:1958 [inline]
__se_sys_execve fs/exec.c:1953 [inline]
__x64_sys_execve+0x8f/0xc0 fs/exec.c:1953
do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Freed by task 5351:
save_stack+0x45/0xd0 mm/kasan/common.c:75
set_track mm/kasan/common.c:87 [inline]
__kasan_slab_free+0x102/0x150 mm/kasan/common.c:459
kasan_slab_free+0xe/0x10 mm/kasan/common.c:467
__cache_free mm/slab.c:3499 [inline]
kmem_cache_free+0x86/0x260 mm/slab.c:3765
__mmdrop+0x238/0x320 kernel/fork.c:677
mmdrop include/linux/sched/mm.h:49 [inline]
finish_task_switch+0x47b/0x780 kernel/sched/core.c:2746
context_switch kernel/sched/core.c:2880 [inline]
__schedule+0x81b/0x1cc0 kernel/sched/core.c:3518
preempt_schedule_irq+0xb5/0x140 kernel/sched/core.c:3745
retint_kernel+0x1b/0x2d
arch_local_irq_restore arch/x86/include/asm/paravirt.h:767 [inline]
kmem_cache_free+0xab/0x260 mm/slab.c:3766
anon_vma_chain_free mm/rmap.c:134 [inline]
unlink_anon_vmas+0x2ba/0x870 mm/rmap.c:401
free_pgtables+0x1af/0x2f0 mm/memory.c:394
exit_mmap+0x2d1/0x530 mm/mmap.c:3144
__mmput kernel/fork.c:1046 [inline]
mmput+0x15f/0x4c0 kernel/fork.c:1067
exec_mmap fs/exec.c:1046 [inline]
flush_old_exec+0x8d9/0x1c20 fs/exec.c:1279
load_elf_binary+0x9bc/0x53f0 fs/binfmt_elf.c:864
search_binary_handler fs/exec.c:1656 [inline]
search_binary_handler+0x17f/0x570 fs/exec.c:1634
exec_binprm fs/exec.c:1698 [inline]
__do_execve_file.isra.0+0x1394/0x23f0 fs/exec.c:1818
do_execveat_common fs/exec.c:1865 [inline]
do_execve fs/exec.c:1882 [inline]
__do_sys_execve fs/exec.c:1958 [inline]
__se_sys_execve fs/exec.c:1953 [inline]
__x64_sys_execve+0x8f/0xc0 fs/exec.c:1953
do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
The buggy address belongs to the object at
ffff88808893f7c0
which belongs to the cache mm_struct of size 1496
The buggy address is located 600 bytes to the right of
1496-byte region [
ffff88808893f7c0,
ffff88808893fd98)
The buggy address belongs to the page:
page:
ffffea0002224f80 count:1 mapcount:0 mapping:
ffff88821bc40ac0 index:0xffff88808893f7c0 compound_mapcount: 0
flags: 0x1fffc0000010200(slab|head)
raw:
01fffc0000010200 ffffea00025b4f08 ffffea00027b9d08 ffff88821bc40ac0
raw:
ffff88808893f7c0 ffff88808893e440 0000000100000001 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff88808893fe80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff88808893ff00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>
ffff88808893ff80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
^
ffff888088940000: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffff888088940080: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Fixes:
e20cf8d3f1f7 ("udp: implement GRO for plain UDP sockets.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Wed, 1 May 2019 21:57:23 +0000 (14:57 -0700)]
Merge tag 'for-v5.1-rc' of git://git./linux/kernel/git/sre/linux-power-supply
Pull power supply fixes from Sebastian Reichel:
"Two more fixes for the 5.1 cycle.
One division by zero fix in a specific driver and one core workaround
for bad userspace behaviour from systemd regarding uevents. IMHO this
can be considered to be a userspace bug, but the debug messages are
useless anyways
- cpcap-battery: fix a division by zero
- core: fix systemd issue due to log messages produced by uevent"
* tag 'for-v5.1-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply:
power: supply: sysfs: prevent endless uevent loop with CONFIG_POWER_SUPPLY_DEBUG
power: supply: cpcap-battery: Fix division by zero
Bodong Wang [Thu, 18 Apr 2019 23:24:15 +0000 (18:24 -0500)]
net/mlx5: E-Switch, Use atomic rep state to serialize state change
When the state of rep was introduced, it was also designed to prevent
duplicate unloading of the same rep. Considering the following two
flows when an eswitch manager is at switchdev mode with n VF reps loaded.
+--------------------------------------+--------------------------------+
| cpu-0 | cpu-1 |
| -------- | -------- |
| mlx5_ib_remove | mlx5_eswitch_disable_sriov |
| mlx5_ib_unregister_vport_reps | esw_offloads_cleanup |
| mlx5_eswitch_unregister_vport_reps | esw_offloads_unload_all_reps |
| __unload_reps_all_vport | __unload_reps_all_vport |
+--------------------------------------+--------------------------------+
These two flows will try to unload the same rep. Per original design,
once one flow unloads the rep, the state moves to REGISTERED. The 2nd
flow will no longer needs to do the unload and bails out. However, as
read and write of the state is not atomic, when 1st flow is doing the
unload, the state is still LOADED, 2nd flow is able to do the same
unload action. Kernel crash will happen.
To solve this, driver should do atomic test-and-set for the state. So
that only one flow can change the rep state from LOADED to REGISTERED,
and proceed to do the actual unloading.
Since the state is changing to atomic type, all other read/write should
be atomic action as well.
Fixes:
f121e0ea9586 (net/mlx5: E-Switch, Add state to eswitch vport representors)
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Vu Pham <vuhuong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Bodong Wang [Mon, 15 Apr 2019 22:39:07 +0000 (17:39 -0500)]
net/mlx5: E-Switch, Fix the check of legal vport
The check of legal vport is to ensure the vport number falls between
0 and total number of vports. Along with the introduction of uplink
rep, enabled vports are not consecutive any more.
Therefore, rely on the eswitch vport getter function to check if it's
a valid vport.
As the getter function relies on eswitch, add the check of vport
group manager and validation the presence of eswitch structure.
Remove the redundant check in the function calls.
Since the vport array will be allocated once eswitch is initialized
and will be kept alive if eswitch presents, no need to protect it with
the state lock.
Fixes:
5ae5162066d8 ("net/mlx5: E-Switch, Assign a different position for uplink rep and vport")
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Bodong Wang [Mon, 15 Apr 2019 22:36:43 +0000 (17:36 -0500)]
net/mlx5: E-Switch, Use getter to access all vport array
Some functions issue vport commands and access vport array using
vport_index/vport_num interchangeably which is OK for VFs vports.
However, this creates potential bug if those vports are not VFs
(E.g, uplink, sf) where their vport_index don't equal to vport_num.
Prepare code to access mlx5_vport structure using a getter function.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Vu Pham <vuhuong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Parav Pandit [Mon, 22 Apr 2019 01:34:45 +0000 (20:34 -0500)]
net/mlx5: Use available mlx5_vport struct
Several functions need to access mlx5_vport and vport_num.
When these functions are called, caller already has mlx5_vport*
available.
Hence pass such mlx5_vport pointer.
This is preparation patch to add error checks to
mlx5_eswitch_get_vport() and to return error status.
By doing so, reduce places where error check of mlx5_eswitch_get_vport()
can be avoided.
While doing such change, mlx5_eswitch_query_vport_drop_stats() gets
corrected to work on vport, instead of vport_idx.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Parav Pandit [Sun, 21 Apr 2019 05:36:21 +0000 (00:36 -0500)]
net/mlx5: Reuse mlx5_esw_for_each_vf_vport macro in two files
Currently mlx5_esw_for_each_vf_vport iterates over mlx5_vport entries in
eswitch.c
Same macro in eswitch_offloads.c iterates over vport number in
eswitch_offloads.c
Instead of duplicate macro names, to avoid confusion and to reuse the
same macro in both files, move it to eswitch.h.
To iterate over vport numbers where there is no need to iterate over
mlx5_vport, but only a vport number is needed, rename those macros in
eswitch_offloads.c to mlx5_esw_for_each_vf_num_vport*.
While at it, keep all vport and vport rep iterators together.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Bodong Wang [Fri, 12 Apr 2019 21:14:03 +0000 (16:14 -0500)]
net/mlx5: Remove unused mlx5_query_nic_vport_vlans
mlx5_query_nic_vport_vlans() is not used anymore. Hence remove it.
This patch doesn't change any functionality.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Masahiro Yamada [Fri, 19 Apr 2019 05:17:31 +0000 (14:17 +0900)]
net/mlx5e: remove meaningless CFLAGS_tracepoint.o
CFLAGS_tracepoint.o specifies CFLAGS for compiling tracepoint.c but
it does not exist under drivers/net/ethernet/mellanox/mlx5/core/.
CFLAGS_tracepoint.o is unused.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Maxim Mikityanskiy [Fri, 1 Mar 2019 11:12:55 +0000 (13:12 +0200)]
net/mlx5e: Put the common XDP code into a function
The same code that returns XDP frames and releases pages is used both in
mlx5e_poll_xdpsq_cq and mlx5e_free_xdpsq_descs. Create a function that
cleans up an MPWQE.
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Erez Alfasi [Thu, 21 Mar 2019 13:02:13 +0000 (15:02 +0200)]
net/mlx5e: ethtool, Add support for EEPROM high pages query
Add the support to read additional EEPROM information from high pages.
Information for modules such as SFF-8436 and SFF-8636:
1) Application select table
2) User writable EEPROM
3) Thresholds and alarms
Signed-off-by: Erez Alfasi <ereza@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Erez Alfasi [Tue, 5 Mar 2019 13:42:23 +0000 (15:42 +0200)]
ethtool: Add SFF-8436 and SFF-8636 max EEPROM length definitions
Added max EEPROM length defines for ethtool usage:
#define ETH_MODULE_SFF_8636_MAX_LEN 640
#define ETH_MODULE_SFF_8436_MAX_LEN 640
These definitions are used to determine the EEPROM
data length when reading high eeprom pages.
For example, SFF-8636 EEPROM data from page 03h
needs to be stored at data[512] - data[639].
Signed-off-by: Erez Alfasi <ereza@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Vlad Buslov [Mon, 15 Apr 2019 07:10:02 +0000 (10:10 +0300)]
net/mlx5e: Return error when trying to insert existing flower filter
With unlocked TC it is possible to have spurious deletes and inserts of
same filter. TC layer needs drivers to always return error when flow
insertion failed in order to correctly calculate "in_hw_count" for each
filter. Fix mlx5e_configure_flower() to return -EEXIST when TC tries to
insert a filter that is already provisioned to the driver.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Eli Britstein [Mon, 4 Mar 2019 13:50:38 +0000 (13:50 +0000)]
net/mlx5e: Replace TC VLAN pop with VLAN 0 rewrite in prio tag mode
Current ConnectX HW is unable to perform VLAN pop in TX path and VLAN
push on RX path. To workaround that limitation untagged packets are
tagged with VLAN ID 0x000 (priority tag) and pop/push actions are
replaced by VLAN re-write actions (which are supported by the HW).
Replace TC VLAN pop action with a VLAN priority tag header rewrite.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Eli Britstein [Mon, 4 Mar 2019 05:01:12 +0000 (05:01 +0000)]
net/mlx5e: ACLs for priority tag mode
Current ConnectX HW is unable to perform VLAN pop in TX path and VLAN
push on RX path. As a workaround, untagged packets are tagged with
VID 0x000 allowing pop/push actions to be exchanged with VLAN rewrite
actions.
Use the ingress ACL table, preceding the FDB, to push VLAN 0x000 ID tag
for untagged packets and the egress ACL table, succeeding the FDB, to
pop VLAN 0x000 ID tag.
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Tariq Toukan [Sun, 20 Jan 2019 09:04:34 +0000 (11:04 +0200)]
net/mlx5e: Turn on HW tunnel offload in all TIRs
Hardware requires that all TIRs that steer traffic to the same RQ
should share identical tunneled_offload_en value.
For that, the tunneled_offload_en bit should be set/unset (according to
the HW capability) for all TIRs', not only the ones dedicated for
tunneled (inner) traffic.
Fixes:
1b223dd39162 ("net/mlx5e: Fix checksum handling for non-stripped vlan packets")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Tariq Toukan [Wed, 16 Jan 2019 12:31:22 +0000 (14:31 +0200)]
net/mlx5e: Take common TIR context settings into a function
Many TIR context settings are common to different TIR types,
take them into a common function.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Martin KaFai Lau [Tue, 30 Apr 2019 17:45:12 +0000 (10:45 -0700)]
ipv6: A few fixes on dereferencing rt->from
It is a followup after the fix in
commit
9c69a1320515 ("route: Avoid crash from dereferencing NULL rt->from")
rt6_do_redirect():
1. NULL checking is needed on rt->from because a parallel
fib6_info delete could happen that sets rt->from to NULL.
(e.g. rt6_remove_exception() and fib6_drop_pcpu_from()).
2. fib6_info_hold() is not enough. Same reason as (1).
Meaning, holding dst->__refcnt cannot ensure
rt->from is not NULL or rt->from->fib6_ref is not 0.
Instead of using fib6_info_hold_safe() which ip6_rt_cache_alloc()
is already doing, this patch chooses to extend the rcu section
to keep "from" dereference-able after checking for NULL.
inet6_rtm_getroute():
1. NULL checking is also needed on rt->from for a similar reason.
Note that inet6_rtm_getroute() is using RTNL_FLAG_DOIT_UNLOCKED.
Fixes:
a68886a69180 ("net/ipv6: Make from in rt6_info rcu protected")
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Wei Wang <weiwan@google.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nicholas Mc Guire [Tue, 30 Apr 2019 03:12:57 +0000 (05:12 +0200)]
rds: ib: force endiannes annotation
While the endiannes is being handled correctly as indicated by the comment
above the offending line - sparse was unhappy with the missing annotation
as be64_to_cpu() expects a __be64 argument. To mitigate this annotation
all involved variables are changed to a consistent __le64 and the
conversion to uint64_t delayed to the call to rds_cong_map_updated().
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 1 May 2019 21:13:14 +0000 (17:13 -0400)]
Merge branch 'net-mvpp2-cls-Add-classification'
Maxime Chevallier says:
====================
net: mvpp2: cls: Add classification
This series is a rework of the previously standalone patch adding
classification support for mvpp2 :
https://lore.kernel.org/netdev/
20190423075031.26074-1-maxime.chevallier@bootlin.com/
This patch has been reworked according to Saeed's review, to make sure
that the location of the rule is always respected and serves as a way to
prioritize rules between each other. This the 3rd iteration of this
submission, but since it's now a series, I reset the revision numbering.
This series implements that in a limited configuration for now, since we
limit the total number of rules per port to 4.
The main factors for this limitation are that :
- We share the classification tables between all ports (4 max, although
one is only used for internal loopback), hence we have to perform a
logical separation between rules, which is done today by dedicated
ranges for each port in each table
- The "Flow table", which dictates which lookups operations are
performed for an ingress packet, in subdivided into 22 "sub flows",
each corresponding to a traffic type based on the L3 proto, L4
proto, the presence or not of a VLAN tag and the L3 fragmentation.
This makes so that when adding a rule, it has to be added into each
of these subflows, introducing duplications of entries and limiting
our max number of entries.
These limitations can be overcomed in several ways, but for readability
sake, I'd rather submit basic classification offload support for now,
and improve it gradually.
This series also adds a small cosmetic cleanup patch (1), and also adds
support for the "Drop" action compared to the first submission of this
feature. It is simple enough to be added with this basic support.
Compared to the first submissions, the NETIF_F_NTUPLE flag was also
removed, following Saeed's comment.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>