OSDN Git Service
Harvey Harrison [Tue, 28 Oct 2008 23:06:44 +0000 (16:06 -0700)]
misc: replace NIP6_FMT with %p6 format specifier
The iscsi_ibft.c changes are almost certainly a bugfix as the
pointer 'ip' is a u8 *, so they never print the last 8 bytes
of the IPv6 address, and the eight bytes they do print have
a zero byte with them in each 16-bit word.
Other than that, this should cause no difference in functionality.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Harvey Harrison [Tue, 28 Oct 2008 23:05:40 +0000 (16:05 -0700)]
net: replace all current users of NIP6_SEQFMT with %#p6
The define in kernel.h can be done away with at a later time.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Harvey Harrison [Tue, 28 Oct 2008 23:04:44 +0000 (16:04 -0700)]
printk: add %p6 format specifier for IPv6 addresses
Takes a pointer to a IPv6 address and formats it in the usual
colon-separated hex format:
xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx
Each 16 bit word is printed in network-endian byteorder.
%#p6 is also supported and will omit the colons.
%p6 is a replacement for NIP6_FMT and NIP6()
%#p6 is a replacement for NIP6_SEQFMT and NIP6()
Note that NIP6() took a struct in6_addr whereas this takes a pointer
to a struct in6_addr.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Martin Willi [Tue, 28 Oct 2008 23:01:07 +0000 (16:01 -0700)]
xfrm: Notify changes in UDP encapsulation via netlink
Add new_mapping() implementation to the netlink xfrm_mgr to notify
address/port changes detected in UDP encapsulated ESP packets.
Signed-off-by: Martin Willi <martin@strongswan.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey Dobriyan [Tue, 28 Oct 2008 20:25:09 +0000 (13:25 -0700)]
net: don't use INIT_RCU_HEAD
call_rcu() will unconditionally rewrite RCU head anyway.
Applies to
struct neigh_parms
struct neigh_table
struct net
struct cipso_v4_doi
struct in_ifaddr
struct in_device
rt->u.dst
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey Dobriyan [Tue, 28 Oct 2008 20:24:06 +0000 (13:24 -0700)]
net: reduce structures when XFRM=n
ifdef out
* struct sk_buff::sp (pointer)
* struct dst_entry::xfrm (pointer)
* struct sock::sk_policy (2 pointers)
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patrick McHardy [Tue, 28 Oct 2008 18:59:11 +0000 (11:59 -0700)]
netlink: constify struct nlattr * arg to parsing functions
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric W. Biederman [Tue, 28 Oct 2008 00:51:47 +0000 (17:51 -0700)]
netns: Coexist with the sysfs limitations v2
To make testing of the network namespace simpler allow
the network namespace code and the sysfs code to be
compiled and run at the same time. To do this only
virtual devices are allowed in the additional network
namespaces and those virtual devices are not placed
in the kobject tree.
Since virtual devices don't actually do anything interesting
hardware wise that needs device management there should
be no loss in keeping them out of the kobject tree and
by implication sysfs. The gain in ease of testing
and code coverage should be significant.
Changelog:
v2: As pointed out by Benjamin Thery it only makes sense to call
device_rename in the initial network namespace for now.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Benjamin Thery <benjamin.thery@bull.net>
Tested-by: Serge Hallyn <serue@us.ibm.com>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Acked-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Tue, 28 Oct 2008 00:47:26 +0000 (17:47 -0700)]
net: convert more to %pM
A number of places still use %02x:...:%02x because it's
in debug statements or for no real reason. Make a few
of them use %pM.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Mon, 27 Oct 2008 22:59:26 +0000 (15:59 -0700)]
net: convert print_mac to %pM
This converts pretty much everything to print_mac. There were
a few things that had conflicts which I have just dropped for
now, no harm done.
I've built an allyesconfig with this and looked at the files
that weren't built very carefully, but it's a huge patch.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg [Mon, 27 Oct 2008 22:56:10 +0000 (15:56 -0700)]
mac80211: convert to %pM away from print_mac
Also remove a few stray DECLARE_MAC_BUF that were no longer
used at all.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Harvey Harrison [Mon, 27 Oct 2008 22:47:12 +0000 (15:47 -0700)]
printk: add %pM format specifier for MAC addresses
Add format specifiers for printing out six colon-separated bytes:
MAC addresses (%pM):
xx:xx:xx:xx:xx:xx
%#pM is also supported and omits the colon separators.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Neil Horman [Mon, 27 Oct 2008 19:28:25 +0000 (12:28 -0700)]
net: implement emergency route cache rebulds when gc_elasticity is exceeded
This is a patch to provide on demand route cache rebuilding. Currently, our
route cache is rebulid periodically regardless of need. This introduced
unneeded periodic latency. This patch offers a better approach. Using code
provided by Eric Dumazet, we compute the standard deviation of the average hash
bucket chain length while running rt_check_expire. Should any given chain
length grow to larger that average plus 4 standard deviations, we trigger an
emergency hash table rebuild for that net namespace. This allows for the common
case in which chains are well behaved and do not grow unevenly to not incur any
latency at all, while those systems (which may be being maliciously attacked),
only rebuild when the attack is detected. This patch take 2 other factors into
account:
1) chains with multiple entries that differ by attributes that do not affect the
hash value are only counted once, so as not to unduly bias system to rebuilding
if features like QOS are heavily used
2) if rebuilding crosses a certain threshold (which is adjustable via the added
sysctl in this patch), route caching is disabled entirely for that net
namespace, since constant rebuilding is less efficient that no caching at all
Tested successfully by me.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 27 Oct 2008 16:37:16 +0000 (09:37 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/ieee1394/linux1394-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
firewire: fw-sbp2: fix races
firewire: fw-sbp2: delay first login to avoid retries
firewire: fw-ohci: initialization failure path fixes
firewire: fw-ohci: don't leak dma memory on module removal
firewire: fix struct fw_node memory leak
firewire: Survive more than 256 bus resets
Linus Torvalds [Mon, 27 Oct 2008 16:36:33 +0000 (09:36 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: ASoC: Blackfin: update SPORT0 port selector (v2)
ALSA: hda - Restore default pin configs for realtek codecs
sound: use a common working email address
pci: use pci_ioremap_bar() in sound/
Takashi Iwai [Mon, 27 Oct 2008 16:08:11 +0000 (17:08 +0100)]
Merge branches 'topic/fix/asoc', 'topic/fix/hda', 'topic/fix/misc' and 'topic/pci-ioremap-bar' into for-linus
Cliff Cai [Mon, 27 Oct 2008 09:09:25 +0000 (17:09 +0800)]
ALSA: ASoC: Blackfin: update SPORT0 port selector (v2)
- Setting the TFS pin selector for SPORT 0 based on whether the selected
port id F or G. If the port is F then no conflict should exist for the
TFS. When Port G is selected and EMAC then there is a conflict between
the PHY interrupt line and TFS. Current settings prevent the conflict
by ignoring the TFS pin when Port G is selected. This allows both
ssm2602 using Port G and EMAC concurrently.
- some code cleanup
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Mon, 27 Oct 2008 15:56:24 +0000 (16:56 +0100)]
ALSA: hda - Restore default pin configs for realtek codecs
Some machines have broken BIOS resume that doesn't restore the default
pin configuration properly, which results in a wrong detection of HP
pin. This causes a silent speaker output due to missing HP detection.
Related bug: Novell bug#406101
https://bugzilla.novell.com/show_bug.cgi?id=406101
This patch fixes the issue by saving/restoring the default pin configs
by the driver itself.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Linus Torvalds [Mon, 27 Oct 2008 15:41:13 +0000 (08:41 -0700)]
Merge git://git./linux/kernel/git/davem/net-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
syncookies: fix inclusion of tcp options in syn-ack
libertas: free sk_buff with kfree_skb
btsdio: free sk_buff with kfree_skb
Phonet: do not reply to indication reset packets
Phonet: include generic link-layer header size in MAX_PHONET_HEADER
Alan Cox [Mon, 27 Oct 2008 15:19:48 +0000 (15:19 +0000)]
Switch to a valid email address...
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Mon, 27 Oct 2008 15:10:23 +0000 (15:10 +0000)]
Tidy up addresses in random drivers
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Eric Miao [Mon, 27 Oct 2008 09:48:50 +0000 (17:48 +0800)]
leds: da903x: fix the building failure of incomplete type of 'work'
The leds-da903x LED driver was missing the proper #include of
linux/workqueue.h, but happened to compile on ARM due to implied
includes through other header files.
We do need the explict include on other architectures (reported at least
for x86-64).
Reported-tested-and-acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alan Cox [Mon, 27 Oct 2008 15:21:19 +0000 (15:21 +0000)]
sound: use a common working email address
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Florian Westphal [Mon, 27 Oct 2008 06:10:12 +0000 (23:10 -0700)]
syncookies: fix inclusion of tcp options in syn-ack
David Miller noticed that commit
33ad798c924b4a1afad3593f2796d465040aadd5 '(tcp: options clean up')
did not move the req->cookie_ts check.
This essentially disabled commit
4dfc2817025965a2fc78a18c50f540736a6b5c24
'[Syncookies]: Add support for TCP options via timestamps.'.
This restores the original logic.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sergio Luis [Mon, 27 Oct 2008 06:09:27 +0000 (23:09 -0700)]
libertas: free sk_buff with kfree_skb
free sk_buff with kfree_skb, instead of kree
Signed-off-by: Sergio Luis <sergio@larces.uece.br>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sergio Luis [Mon, 27 Oct 2008 06:08:48 +0000 (23:08 -0700)]
btsdio: free sk_buff with kfree_skb
free sk_buff with kfree_skb, instead of kree
Signed-off-by: Sergio Luis <sergio@larces.uece.br>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remi Denis-Courmont [Mon, 27 Oct 2008 06:07:25 +0000 (23:07 -0700)]
Phonet: do not reply to indication reset packets
This fixes a potential error packet loop.
Signed-off-by: Remi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remi Denis-Courmont [Mon, 27 Oct 2008 06:06:31 +0000 (23:06 -0700)]
Phonet: include generic link-layer header size in MAX_PHONET_HEADER
This fixes an OOPS in hard_header if a Phonet address is assigned to a
non-Phonet network interface.
Signed-off-by: Remi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Sun, 26 Oct 2008 23:42:18 +0000 (16:42 -0700)]
Merge branch 'for-linus' of git://neil.brown.name/md
* 'for-linus' of git://neil.brown.name/md:
md: allow extended partitions on md devices.
md: use sysfs_notify_dirent to notify changes to md/dev-xxx/state
md: use sysfs_notify_dirent to notify changes to md/array_state
Linus Torvalds [Sun, 26 Oct 2008 23:40:59 +0000 (16:40 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: psmouse - add support for Elantech touchpads
Input: i8042 - add Blue FB5601 to noloop exception table
Linus Torvalds [Sun, 26 Oct 2008 23:37:37 +0000 (16:37 -0700)]
Merge branch 'for-linus' of git://git.o-hand.com/linux-mfd
* 'for-linus' of git://git.o-hand.com/linux-mfd:
mfd: Make WM8400 depend on I2C until SPI is submitted
mfd: add missing Kconfig entry for da903x
Linus Torvalds [Sun, 26 Oct 2008 23:35:41 +0000 (16:35 -0700)]
Merge branch 'for-upstream' of git://git./linux/kernel/git/dvrabel/uwb
* 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/dvrabel/uwb:
uwb: build UWB before USB/WUSB
Linus Torvalds [Sun, 26 Oct 2008 23:34:14 +0000 (16:34 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jikos/hid
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: Add support for Sony Vaio VGX-TP1E
HID: fix lock imbalance in hiddev
HID: fix lock imbalance in hidraw
HID: fix hidbus/appletouch device binding regression
HID: add hid_type to general hid struct
HID: quirk for OLED devices present in ASUS G50/G70/G71
HID: Remove "default m" for Thrustmaster and Zeroplus
HID: fix hidraw_exit section mismatch
HID: add support for another Gyration remote control
Revert "HID: Invert HWHEEL mappings for some Logitech mice"
Randy Dunlap [Sun, 26 Oct 2008 00:24:36 +0000 (17:24 -0700)]
docbooks: fix fatal filename errors
Fix docbook fatal errors (file location changed):
docproc: lin2628-rc1/include/asm-x86/io_32.h: No such file or directory
make[1]: *** [Documentation/DocBook/deviceiobook.xml] Error 1
docproc: lin2628-rc1/include/asm-x86/atomic_32.h: No such file or directory
make[1]: *** [Documentation/DocBook/kernel-api.xml] Error 1
docproc: lin2628-rc1/include/asm-x86/mca_dma.h: No such file or directory
make[1]: *** [Documentation/DocBook/mcabook.xml] Error 1
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Randy Dunlap [Sun, 26 Oct 2008 00:06:43 +0000 (17:06 -0700)]
kernel-doc: allow more whitespace in macros
Allow macros that are annotated with kernel-doc to contain whitespace
between the '#' and "define". It's valid and being used, so allow it.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 26 Oct 2008 23:29:12 +0000 (16:29 -0700)]
Merge branch 'release' of git://git./linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
leds-hp-disk: fix build warning
ACPI: Oops in ACPI with git latest
ACPI suspend: build fix for ACPI_SLEEP=n && XEN_SAVE_RESTORE=y.
toshiba_acpi: always call input_sync() after input_report_switch()
ACPI: Always report a sync event after a lid state change
ACPI: cpufreq, processor: fix compile error in drivers/acpi/processor_perflib.c
i7300_idle: Fix compile warning CONFIG_I7300_IDLE_IOAT_CHANNEL not defined
i7300_idle: Cleanup based review comments
i7300_idle: Disable ioat channel only on platforms where ile driver can load
Linus Torvalds [Sun, 26 Oct 2008 19:13:29 +0000 (12:13 -0700)]
Linux 2.6.28-rc2
.. fix all the worst problems in -rc1
Geert Uytterhoeven [Sun, 26 Oct 2008 18:51:14 +0000 (19:51 +0100)]
m68k: Disable Amiga serial console support if modular
If CONFIG_AMIGA_BUILTIN_SERIAL=m, I get the following warnings:
| drivers/char/amiserial.c: At top level:
| drivers/char/amiserial.c:2138: warning: data definition has no type or storage class
| drivers/char/amiserial.c:2138: warning: type defaults to 'int' in declaration of 'console_initcall'
| drivers/char/amiserial.c:2138: warning: parameter names (without types) in function declaration
| drivers/char/amiserial.c:2134: warning: 'amiserial_console_init' defined but not used
because console_initcall() is not defined (nor really sensible) in the
modular case.
So disable serial console support if the driver is modular.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Davide Libenzi [Fri, 17 Oct 2008 23:17:40 +0000 (16:17 -0700)]
epoll: avoid double-inserts in case of EFAULT
In commit
f337b9c58332bdecde965b436e47ea4c94d30da0 ("epoll: drop
unnecessary test") Thomas found that there is an unnecessary (always
true) test in ep_send_events(). The callback never inserts into
->rdllink while the send loop is performed, and also does the
~EP_PRIVATE_BITS test. Given we're holding the mutex during this time,
the conditions tested inside the loop are always true.
HOWEVER.
The test "!ep_is_linked(&epi->rdllink)" wasn't there because we insert
into ->rdllink, but because the send-events loop might terminate before
the whole list is scanned (-EFAULT).
In such cases, when the loop terminates early, and when a (leftover)
file received an event while we're performing the lockless loop, we need
such test to avoid to double insert the epoll items. The list_splice()
done a few steps below, will correctly re-insert the ones that were left
on "txlist".
This should fix the kenrel.org bugzilla entry 11831.
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arjan van de Ven [Sat, 25 Oct 2008 19:41:41 +0000 (12:41 -0700)]
select: deal with math overflow from borderline valid userland data
Some userland apps seem to pass in a "0" for the seconds, and several
seconds worth of usecs to select(). The old kernels accepted this just
fine, so the new kernels must too.
However, due to the upscaling of the microseconds to nanoseconds we had
some cases where we got math overflow, and depending on the GCC version
(due to inlining decisions) that actually resulted in an -EINVAL return.
This patch fixes this by adding the excess microseconds to the seconds
field.
Also with thanks to Marcin Slusarz for spotting some implementation bugs
in the diagnostics patches.
Reported-by: Carlos R. Mafra <crmafra2@gmail.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Arjan van de Ven [Sun, 26 Oct 2008 17:25:30 +0000 (10:25 -0700)]
wireless: fix regression caused by regulatory config option
The default for the regulatory compatibility option is wrong;
if you picked the default you ended up with a non-functional wifi
system (at least I did on Fedora 9 with iwl4965).
I don't think even the October 2008 releases of the various distros
has the new userland so clearly the default is wrong, and also
we can't just go about deleting this in 2.6.29...
Change the default to "y" and also adjust the config text a little to
reflect this.
This patch fixes regression #11859
With thanks to Johannes Berg for the diagnostics
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Stephen Rothwell [Tue, 21 Oct 2008 05:11:20 +0000 (16:11 +1100)]
cgroup: remove unused variable
/scratch/sfr/next/kernel/cgroup.c: In function 'cgroup_tasks_start':
/scratch/sfr/next/kernel/cgroup.c:2107: warning: unused variable 'i'
Introduced in commit
cc31edceee04a7b87f2be48f9489ebb72d264844 "cgroups:
convert tasks file to use a seq_file with shared pid array".
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 26 Oct 2008 16:36:19 +0000 (09:36 -0700)]
Merge branch 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6
* 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
hwmon: (abituguru3) enable DMI probing feature on AW9D-MAX
hwmon: (abituguru3) Cosmetic whitespace fixes
hwmon: (adt7473) Fix voltage conversion routines
hwmon: (lm90) Add support for the LM99 16 degree offset
hwmon: (lm90) Fix handling of hysteresis value
hwmon-vid: Add support for AMD family 10h CPUs
hwmon: (w83781d) Fix linking when built-in
Francois Romieu [Sun, 26 Oct 2008 16:02:49 +0000 (17:02 +0100)]
r8169: revert "read MAC address from EEPROM on init"
This reverts commit
7bf6bf4803df1adc927f585168d2135fb019c698.
The code has both a short existence and an increasing track of failures
despite some work to amend it for -rc1. It is not just a matter of
reading the eeprom: sometimes the eeprom is read correctly, then the mac
address is not written correctly back into the mac registers.
Some chipsets seem to work reliably but it is not clear at this point if
the code can simply be made to work on a per-chipset basis and post -rc1
is not the place where I want to experiment these things.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Al Viro [Sun, 26 Oct 2008 05:40:26 +0000 (05:40 +0000)]
arm ide breakage
a) semicolon before the function body is a bad idea
b) it's const struct foo, not struct const foo
c) incidentally, it's ecard_remove_driver(), not ecard_unregister_driver()
d) compiling is occasionally useful.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Al Viro [Sun, 26 Oct 2008 05:12:34 +0000 (05:12 +0000)]
fix allmodconfig breakage
If you use KCONFIG_ALLCONFIG (even with empty file) you get broken
allmodconfig/allyesconfig; CONFIG_MODULES gets turned off, with obvious
massive fallout.
Breakage had been introduced when conf_set_all_new_symbols() got used
for allmodconfig et.al.
What happens is that sym_calc_value(modules_sym) done in
conf_read_simple() sets SYMBOL_VALID on both modules_sym and MODULES.
When we get to conf_set_all_new_symbols(), we set sym->def[S_DEF_USER]
on everything, but it has no effect on sym->curr for the symbols that
already have SYMBOL_VALID - these are stuck.
Solution: use sym_clear_all_valid() in there. Note that it makes
reevaluation of modules_sym redundant - sym_clear_all_valid() will do
that itself.
[ Fixes http://bugzilla.kernel.org/show_bug.cgi?id=11512, says Alexey ]
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alistair John Strachan [Sun, 26 Oct 2008 16:04:40 +0000 (17:04 +0100)]
hwmon: (abituguru3) enable DMI probing feature on AW9D-MAX
Switch the AW9D-MAX over from port probing to the preferred DMI
probe method.
Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk>
Tested-by: Justin Piszcz <jpiszcz@lucidpixels.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Alistair John Strachan [Sun, 26 Oct 2008 16:04:40 +0000 (17:04 +0100)]
hwmon: (abituguru3) Cosmetic whitespace fixes
As the probable result of zealous copy/pasting, many supported boards
contain sensor names with trailing whitespace. Though this is not a
huge problem, it is inconsistent with other sensor names, and with
other similar hwmon drivers.
Additionally, the DMI nag message added in 2.6.27 was missing a
space between two sentence fragments -- might as well clean that up
too.
Doesn't alter any kernel text, just data.
Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk>
Reported-by: Justin Piszcz <jpiszcz@lucidpixels.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Jean Delvare [Sun, 26 Oct 2008 16:04:40 +0000 (17:04 +0100)]
hwmon: (adt7473) Fix voltage conversion routines
Fix voltage conversion routines. Based on an earlier patch from
Paulius Zaleckas.
According to the datasheet voltage is scaled with resistors and
value 192 is nominal voltage. 0 is 0V.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Cc: Darrick J. Wong <djwong@us.ibm.com>
Jean Delvare [Sun, 26 Oct 2008 16:04:39 +0000 (17:04 +0100)]
hwmon: (lm90) Add support for the LM99 16 degree offset
The LM99 differs from the LM86, LM89 and LM90 in that it reports
remote temperatures (temp2) 16 degrees lower than they really are. So
far we have been cheating and handled this in userspace but it really
should be handled by the driver directly.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Jean Delvare [Sun, 26 Oct 2008 16:04:39 +0000 (17:04 +0100)]
hwmon: (lm90) Fix handling of hysteresis value
There are several problems in the way the hysteresis value is handled
by the lm90 driver:
* In show_temphyst(), specific handling of the MAX6646 is missing, so
the hysteresis is reported incorrectly if the critical temperature
is over 127 degrees C.
* In set_temphyst(), the new hysteresis register value is written to
the chip but data->temp_hyst isn't updated accordingly, so there is
a short period of time (up to 2 seconds) where the old hystereris
value will be returned while the new one is already active.
* In set_temphyst(), the critical temperature which is used as a base
to compute the value of the hysteresis register lacks
device-specific handling. As a result, the value of the hysteresis
register might be incorrect for the ADT7461 and MAX6646 chips.
Fix these 3 bugs.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Nate Case <ncase@xes-inc.com>
Jean Delvare [Sun, 26 Oct 2008 16:04:39 +0000 (17:04 +0100)]
hwmon-vid: Add support for AMD family 10h CPUs
The AMD family 10h CPUs use the same VID decoding table as the family
0Fh CPUs.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Rudolf Marek <r.marek@assembler.cz>
Geert Uytterhoeven [Sun, 26 Oct 2008 16:04:38 +0000 (17:04 +0100)]
hwmon: (w83781d) Fix linking when built-in
When w83781d is built-in, the final links fails with the following vague error
message:
`.exit.text' referenced in section `.init.text' of drivers/built-in.o: defined
in discarded section `.exit.text' of drivers/built-in.o
w83781d_isa_unregister() cannot be marked __exit, as it's also called from
sensors_w83781d_init(), which is marked __init.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Jay Fenlason [Fri, 24 Oct 2008 19:26:20 +0000 (15:26 -0400)]
firewire: fw-sbp2: fix races
1: There is a small race between queue_delayed_work() and its
corresponding kref_get(). Do the kref_get first, and _put it again
if the queue_delayed_work() failed, so there is no chance of the
kref going to zero while the work is scheduled.
2: An SBP2_LOGOUT_REQUEST could be sent out with a login_id full of
garbage. Initialize it to an invalid value so we can tell if we
ever got a valid login_id.
3: The node ID and generation may have changed but the new values may
not yet have been recorded in lu and tgt when the final logout is
attempted. Use the latest values from the device in
sbp2_release_target().
Signed-off-by: Jay Fenlason <fenlason@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Tue, 21 Oct 2008 22:28:36 +0000 (00:28 +0200)]
firewire: fw-sbp2: delay first login to avoid retries
This optimizes firewire-sbp2's device probe for the case that the local
node and the SBP-2 node were discovered at the same time. In this case,
fw-core's bus management work and fw-sbp2's login and SCSI probe work
are scheduled in parallel (in the globally shared workqueue and in
fw-sbp2's workqueue, respectively). The bus reset from fw-core may then
disturb and extremely delay the login and SCSI probe because the latter
fails with several command timeouts and retries and has to be retried
from scratch.
We avoid this particular situation of sbp2_login() and fw_card_bm_work()
running in parallel by delaying the first sbp2_login() a little bit.
This is meant to be a short-term fix for
https://bugzilla.redhat.com/show_bug.cgi?id=466679. In the long run,
the SCSI probe, i.e. fw-sbp2's call of __scsi_add_device(), should be
parallelized with sbp2_reconnect().
Problem reported and fix tested and confirmed by Alex Kanavin.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Sun, 26 Oct 2008 08:50:31 +0000 (09:50 +0100)]
firewire: fw-ohci: initialization failure path fixes
Fix leaks when pci_probe fails. Simplify error log strings.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Jay Fenlason [Wed, 22 Oct 2008 19:59:42 +0000 (15:59 -0400)]
firewire: fw-ohci: don't leak dma memory on module removal
The transmit and receive context dma memory was not being freed on
module removal. Neither was the config rom memory. Fix that.
The ab->next assignment is pure paranoia.
Signed-off-by: Jay Fenlason <fenlason@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Jay Fenlason [Thu, 16 Oct 2008 22:00:15 +0000 (18:00 -0400)]
firewire: fix struct fw_node memory leak
With the bus_resets patch applied, it is easy to see this memory leak
by repeatedly resetting the firewire bus while running slabtop in
another window. Just watch kmalloc-32 grow and grow...
Signed-off-by: Jay Fenlason <fenlason@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Jay Fenlason [Thu, 16 Oct 2008 19:51:59 +0000 (15:51 -0400)]
firewire: Survive more than 256 bus resets
The "color" is used during the topology building after a bus reset,
hovever in "struct fw_node"s it is stored in a u8, but in struct fw_card
it is stored in an int. When the value wraps in one struct, but not
the other, disaster strikes.
Signed-off-by: Jay Fenlason <fenlason@redhat.com>
Fixes http://bugzilla.kernel.org/show_bug.cgi?id=10922.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Linus Torvalds [Sun, 26 Oct 2008 02:57:30 +0000 (19:57 -0700)]
Merge branch 'for_linus' of git://git./linux/kernel/git/tytso/ext4
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: Fix duplicate entries returned from getdents() system call
ext3: Fix duplicate entries returned from getdents() system call
Linus Torvalds [Sun, 26 Oct 2008 02:53:38 +0000 (19:53 -0700)]
Revert "Call init_workqueues before pre smp initcalls."
This reverts commit
a802dd0eb5fc97a50cf1abb1f788a8f6cc5db635 by moving
the call to init_workqueues() back where it belongs - after SMP has been
initialized.
It also moves stop_machine_init() - which needs workqueues - to a later
phase using a core_initcall() instead of early_initcall(). That should
satisfy all ordering requirements, and was apparently the reason why
init_workqueues() was moved to be too early.
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Theodore Ts'o [Sat, 25 Oct 2008 15:39:08 +0000 (11:39 -0400)]
ext4: Fix duplicate entries returned from getdents() system call
Fix a regression caused by commit
d0156417, "ext4: fix ext4_dx_readdir
hash collision handling", where deleting files in a large directory
(requiring more than one getdents system call), results in some
filenames being returned twice. This was caused by a failure to
update info->curr_hash and info->curr_minor_hash, so that if the
directory had gotten modified since the last getdents() system call
(as would be the case if the user is running "rm -r" or "git clean"),
a directory entry would get returned twice to the userspace.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
This patch fixes the bug reported by Markus Trippelsdorf at:
http://bugzilla.kernel.org/show_bug.cgi?id=11844
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Theodore Ts'o [Sat, 25 Oct 2008 15:38:37 +0000 (11:38 -0400)]
ext3: Fix duplicate entries returned from getdents() system call
Fix a regression caused by commit
6a897cf4, "ext3: fix ext3_dx_readdir
hash collision handling", where deleting files in a large directory
(requiring more than one getdents system call), results in some
filenames being returned twice. This was caused by a failure to
update info->curr_hash and info->curr_minor_hash, so that if the
directory had gotten modified since the last getdents() system call
(as would be the case if the user is running "rm -r" or "git clean"),
a directory entry would get returned twice to the userspace.
This patch fixes the bug reported by Markus Trippelsdorf at:
http://bugzilla.kernel.org/show_bug.cgi?id=11844
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Len Brown [Sat, 25 Oct 2008 08:07:44 +0000 (04:07 -0400)]
Merge branch 'i7300_idle' into release
Len Brown [Sat, 25 Oct 2008 07:52:16 +0000 (03:52 -0400)]
leds-hp-disk: fix build warning
drivers/leds/leds-hp-disk.c:59: warning: passing argument 4 of ‘acpi_evaluate_integer’ from incompatible pointer type
Signed-off-by: Len Brown <len.brown@intel.com>
Rafael J. Wysocki [Fri, 24 Oct 2008 19:50:31 +0000 (21:50 +0200)]
ACPI: Oops in ACPI with git latest
ACPI Warning (nseval-0168): Insufficient arguments - method [_OSC] needs 5, found 4 [
20080926]
ACPI Warning (nspredef-0252): \_SB_.PCI0._OSC: Parameter count mismatch - ASL declared 5, expected 4 [
20080926]
ACPI Error (nspredef-0163): \_SB_.PCI0._OSC: Missing expected return value [
20080926]
BUG: unable to handle kernel NULL pointer dereference at
00000000
IP: [<
c0237671>] acpi_run_osc+0xa1/0x170
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Rafael J. Wysocki [Thu, 23 Oct 2008 19:46:43 +0000 (21:46 +0200)]
ACPI suspend: build fix for ACPI_SLEEP=n && XEN_SAVE_RESTORE=y.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Len Brown [Fri, 24 Oct 2008 19:39:47 +0000 (15:39 -0400)]
toshiba_acpi: always call input_sync() after input_report_switch()
Signed-off-by: Len Brown <len.brown@intel.com>
Guillem Jover [Thu, 23 Oct 2008 21:28:33 +0000 (00:28 +0300)]
ACPI: Always report a sync event after a lid state change
Currently not always an EV_SYN event is reported to userland
after the EV_SW SW_LID event has been sent. This is easy to verify
by using “input-events” from input-utils and just closing and opening
the lid.
Signed-off-by: Guillem Jover <guillem.jover@nokia.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Miao Xie [Fri, 24 Oct 2008 09:22:04 +0000 (17:22 +0800)]
ACPI: cpufreq, processor: fix compile error in drivers/acpi/processor_perflib.c
When trying to build 2.6.28-rc1 on ia64, make aborts with:
CC drivers/acpi/processor_perflib.o
drivers/acpi/processor_perflib.c:41:28: error: asm/cpufeature.h: No such file or directory
drivers/acpi/processor_perflib.c: In function ‘acpi_processor_get_performance_info’:
drivers/acpi/processor_perflib.c:364: error: implicit declaration of function ‘boot_cpu_has’
drivers/acpi/processor_perflib.c:364: error: ‘X86_FEATURE_EST’ undeclared (first use in this function)
drivers/acpi/processor_perflib.c:364: error: (Each undeclared identifier is reported only once
drivers/acpi/processor_perflib.c:364: error: for each function it appears in.)
make[2]: *** [drivers/acpi/processor_perflib.o] Error 1
make[1]: *** [drivers/acpi] Error 2
make: *** [drivers] Error 2
this patch fix it.
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Acked-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Venki Pallipadi [Thu, 23 Oct 2008 22:39:06 +0000 (15:39 -0700)]
i7300_idle: Fix compile warning CONFIG_I7300_IDLE_IOAT_CHANNEL not defined
When I7300_idle driver is not configured, there is a compile time
warning about IDLE_IOAT_CHANNEL not defined. Fix it.
Reported-by: Suresh Siddha <suresh.b.siddha@intel.com>
Reported-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Venki Pallipadi [Wed, 22 Oct 2008 23:51:03 +0000 (16:51 -0700)]
i7300_idle: Cleanup based review comments
Cleanup of i7300 idle driver based on review comments from Randy Dunlap,
Andi Kleen and Len Brown.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Venki Pallipadi [Wed, 22 Oct 2008 23:34:52 +0000 (16:34 -0700)]
i7300_idle: Disable ioat channel only on platforms where ile driver can load
Based on input from Andi Kleen:
share the platform detection code with ioat_dma and disable the channel in
dma engine only for specific platforms.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Mark Brown [Fri, 24 Oct 2008 15:16:11 +0000 (17:16 +0200)]
mfd: Make WM8400 depend on I2C until SPI is submitted
Otherwise we could build in WM8400 but not I2C.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Samuel Ortiz [Fri, 24 Oct 2008 15:10:05 +0000 (17:10 +0200)]
mfd: add missing Kconfig entry for da903x
This one was accidentally left out during the rc1 mfd merge.
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
David Vrabel [Fri, 24 Oct 2008 15:46:22 +0000 (16:46 +0100)]
uwb: build UWB before USB/WUSB
The WHCI-HCD driver in drivers/usb/host/ depends on the umc driver in
drivers/uwb/.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Jens Axboe [Fri, 24 Oct 2008 07:22:42 +0000 (09:22 +0200)]
libata: fix bug with non-ncq devices
The recent commit
2fca5ccf97d2c28bcfce44f5b07d85e74e3cd18e ("libata:
switch to using block layer tagging support") to enable support for
block layer tagging in libata was broken for non-NCQ devices
The block layer initializes the tag field to -1 to detect invalid uses
of a tag, and if the libata devices does NOT support NCQ, we just used
that field to index the internal command list. So we need to check for
-1 first and only use the tag field if it's valid.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Reported-by: Alexander Beregalov <a.beregalov@gmail.com>
Tested-by: Paul Mundt <lethal@linux-sh.org>
Tested-by: Dave Young <hidave.darkstar@gmail.com>
Tested-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 24 Oct 2008 03:06:52 +0000 (20:06 -0700)]
Linux 2.6.28-rc1
Randy Dunlap [Fri, 24 Oct 2008 01:14:55 +0000 (18:14 -0700)]
Fix PCI hotplug printk format
Fix printk format warning:
drivers/pci/hotplug/acpiphp_ibm.c:207: warning: format '%08lx' expects type 'long unsigned int', but argument 3 has type 'long long unsigned int'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 24 Oct 2008 02:31:34 +0000 (19:31 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/jbarnes/pci-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: remove unused resource assignment in pci_read_bridge_bases()
PCI hotplug: shpchp: message refinement
PCI hotplug: shpchp: replace printk with dev_printk
PCI: add routines for debugging and handling lost interrupts
PCI hotplug: pciehp: message refinement
PCI: fix ARI code to be compatible with mixed ARI/non-ARI systems
PCI hotplug: cpqphp: fix kernel NULL pointer dereference
Linus Torvalds [Fri, 24 Oct 2008 02:19:54 +0000 (19:19 -0700)]
Merge git://git./linux/kernel/git/davem/net-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (29 commits)
tcp: Restore ordering of TCP options for the sake of inter-operability
net: Fix disjunct computation of netdev features
sctp: Fix to handle SHUTDOWN in SHUTDOWN_RECEIVED state
sctp: Fix to handle SHUTDOWN in SHUTDOWN-PENDING state
sctp: Add check for the TSN field of the SHUTDOWN chunk
sctp: Drop ICMP packet too big message with MTU larger than current PMTU
p54: enable 2.4/5GHz spectrum by eeprom bits.
orinoco: reduce stack usage in firmware download path
ath5k: fix suspend-related oops on rmmod
[netdrvr] fec_mpc52xx: Implement polling, to make netconsole work.
qlge: Fix MSI/legacy single interrupt bug.
smc911x: Make the driver safer on SMP
smc911x: Add IRQ polarity configuration
smc911x: Allow Kconfig dependency on ARM
sis190: add identifier for Atheros AR8021 PHY
8139x: reduce message severity on driver overlap
igb: add IGB_DCA instead of selecting INTEL_IOATDMA
igb: fix tx data corruption with transition to L0s on 82575
ehea: Fix memory hotplug support
netdev: DM9000: remove BLACKFIN hacking in DM9000 netdev driver
...
Linus Torvalds [Fri, 24 Oct 2008 02:19:14 +0000 (19:19 -0700)]
Merge git://git./linux/kernel/git/davem/sparc-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
math-emu: Fix thinko in _FP_DIV
math-emu: Fix signalling of underflow and inexact while packing result.
sparc: Add checkstack support
sparc: correct section of current_pc()
sparc: correct section of apc_no_idle
sparc64: Fix race in arch/sparc64/kernel/trampoline.S
Zhao, Yu [Mon, 13 Oct 2008 13:02:27 +0000 (21:02 +0800)]
PCI: remove unused resource assignment in pci_read_bridge_bases()
This cleanup removes the resource assignment in pci_read_bridge_bases()
since it has taken care by pci_alloc_child_bus() when allocating the bus:
/* Set up default resource pointers and names.. */
for (i = 0; i < PCI_BRIDGE_RES_NUM; i++) {
child->resource[i] = &bridge->resource[PCI_BRIDGE_RESOURCES+i];
child->resource[i]->name = child->name;
}
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Taku Izumi [Thu, 23 Oct 2008 02:54:39 +0000 (11:54 +0900)]
PCI hotplug: shpchp: message refinement
This patch refines messages in shpchp module. The main changes are as
follows:
- remove the trailing "."
- remove __func__ as much as possible
- capitalize the first letter of messages
- show PCI device address including its domain
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Taku Izumi [Thu, 23 Oct 2008 02:52:12 +0000 (11:52 +0900)]
PCI hotplug: shpchp: replace printk with dev_printk
This patch replaces printks within shpchp module with dev_printks.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Linus Torvalds [Thu, 23 Oct 2008 23:08:11 +0000 (16:08 -0700)]
Merge git://git./linux/kernel/git/bart/ide-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
ide: drivers/ide/generic.c -> drivers/ide/ide-pci-generic.c
ide-disk: set non-rotational queue flag for SSD and CF devices
ide-cd: add TEAC CD-224E to the NO_AUTOCLOSE list
ide: Add tx4938ide driver (v2)
TXx9: Add TX4938 ATA support (v3)
ide: Add tx4939ide driver (v6)
ide: two more pci_ioremap_bar() conversions
pci: use pci_ioremap_bar() in drivers/ide
sgiioc4: use ide_host_add() (take 2)
sgiioc4: fix error cleanup path (take 2)
Linus Torvalds [Thu, 23 Oct 2008 23:07:32 +0000 (16:07 -0700)]
Merge branch 'for-linus' of git://git.o-hand.com/linux-rpurdie-leds
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-leds:
leds/acpi: Fix merge fallout from acpi_driver_data change
leds: Simplify logic in leds-ams-delta
leds: Fix trigger registration race
leds: Fix leds-class.c comment
leds: Add driver for HP harddisk protection LEDs
leds: leds-pca955x - Mark pca955x_led_set() static
leds: Remove uneeded leds-cm-x270 driver
leds: Remove uneeded strlen calls
leds: Add leds-wrap default-trigger
leds: Make default trigger fields const
leds: Add backlight LED trigger
leds: da903x: Add support for LEDs found on DA9030/DA9034
Linus Torvalds [Thu, 23 Oct 2008 23:06:49 +0000 (16:06 -0700)]
Merge branch 'for-linus' of /home/rmk/linux-2.6-arm
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] pxa: corgi backlight driver should not select ssp drivers
[ARM] 5321/1: Kirkwood: fix typo in Makefile
[ARM] 5320/1: fix assembly constraints in implementation of do_div()
[ARM] 5318/1: Swap the PRRR and NMRR values in proc-v7.S
[ARM] 5316/1: AT91: oops (regression) fix on gpio irq
[ARM] msm: vreg interface to msm7k pmic
[ARM] msm: dma: various basic dma improvements and bugfixes
[ARM] msm: clock: provide clk_*() api support for
[ARM] msm: clean up iomap and devices
[ARM] msm: add proc_comm support, necessary for clock and power control
[ARM] msm: rename ARCH_MSM7X00A to ARCH_MSM
[ARM] pxa/spitz: fix unbalance parenthesis in header file spitz.h
[ARM] pxa: update {corgi,spitz}_defconfig to favor SPI-based drivers
[ARM] pxa: fix the corgi_ssp.c dependency issue in {corgi,spitz}_defconfig
Revert "[ARM] pxa/corgi: remove now unused corgi_ssp.c and corgi_lcd.c"
Linus Torvalds [Thu, 23 Oct 2008 23:05:59 +0000 (16:05 -0700)]
Merge branch 'for-linus' of git://git.o-hand.com/linux-rpurdie-backlight
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-backlight:
backlight: Add driver for Tabletkiosk Sahara TouchIT-213 Tablet PC
backlight: da903x: Add backlight driver for DA9030/DA9034
tosa: add support for bl/lcd driver
backlight: add support for Sharp SL-6000 LCD and backlight drivers
Jens Axboe [Wed, 22 Oct 2008 07:34:49 +0000 (09:34 +0200)]
libata: switch to using block layer tagging support
libata currently has a pretty dumb ATA_MAX_QUEUE loop for finding
a free tag to use. Instead of fixing that up, convert libata to
using block layer tagging - gets rid of code in libata, and is also
much faster.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
James Bottomley [Sun, 3 Aug 2008 18:02:12 +0000 (13:02 -0500)]
PCI: add routines for debugging and handling lost interrupts
We're getting a lot of storage drivers blamed for interrupt misrouting
issues. This patch provides a standard way of reporting the problem
... and, if possible, correcting it.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Taku Izumi [Thu, 23 Oct 2008 02:47:32 +0000 (11:47 +0900)]
PCI hotplug: pciehp: message refinement
This patch refines messages in pciehp module. The main changes are as
follows:
- remove the trailing "."
- remove __func__ as much as possible
- capitalize the first letter of messages
- show PCI device address including its domain
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Zhao, Yu [Thu, 23 Oct 2008 05:15:39 +0000 (13:15 +0800)]
PCI: fix ARI code to be compatible with mixed ARI/non-ARI systems
The original ARI support code has a compatibility problem with non-ARI
devices. If a device doesn't support ARI, turning on ARI forwarding on
its upper level bridge will cause undefined behavior.
This fix turns on ARI forwarding only when the subordinate devices
support it.
Tested-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Kenji Kaneshige [Fri, 17 Oct 2008 00:23:51 +0000 (09:23 +0900)]
PCI hotplug: cpqphp: fix kernel NULL pointer dereference
The following patch fixes the regression in 2.6.27 that causes kernel
NULL pointer dereference at cpqphp driver probe time. This patch should
be backported to the .27 stable series.
Seems to have been introduced by
f46753c5e354b857b20ab8e0fe7b2579831dc369.
The root cause of this problem seems that cpqphp driver calls
pci_hp_register() wrongly. In current implementation, cpqphp driver
passes 'ctrl->pci_dev->subordinate' as a second parameter for
pci_hp_register(). But because hotplug slots and it's hotplug controller
(exists as a pci funcion) are on the same bus, it should be
'ctrl->pci_dev->bus' instead.
Cc: <stable@kernel.org>
Tested-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Stephen Rothwell [Thu, 23 Oct 2008 21:35:19 +0000 (22:35 +0100)]
leds/acpi: Fix merge fallout from acpi_driver_data change
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
Bartlomiej Zolnierkiewicz [Thu, 23 Oct 2008 21:24:20 +0000 (23:24 +0200)]
ide: drivers/ide/generic.c -> drivers/ide/ide-pci-generic.c
Suggested-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Bartlomiej Zolnierkiewicz [Thu, 23 Oct 2008 21:22:09 +0000 (23:22 +0200)]
ide-disk: set non-rotational queue flag for SSD and CF devices
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Márton Németh [Thu, 23 Oct 2008 21:22:09 +0000 (23:22 +0200)]
ide-cd: add TEAC CD-224E to the NO_AUTOCLOSE list
The "TEAC CD-ROM CD-224E" cannot close its tray, so add it to the NO_AUTOCLOSE
list. This will correct the "Can close tray" field of /proc/sys/dev/cdrom/info.
Signed-off-by: Márton Németh <nm127@freemail.hu>
Acked-by: Borislav Petkov <petkovbb@gmail.com>
[bart: minor fixups to patch description]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Atsushi Nemoto [Thu, 23 Oct 2008 21:22:08 +0000 (23:22 +0200)]
ide: Add tx4938ide driver (v2)
This is the driver for the Toshiba TX4938 SoC EBUS controller ATA mode.
It has custom set_pio_mode and some hacks for big endian.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: ralf@linux-mips.org
Cc: sshtylyov@ru.mvista.com
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Atsushi Nemoto [Thu, 23 Oct 2008 21:22:08 +0000 (23:22 +0200)]
TXx9: Add TX4938 ATA support (v3)
Add a helper routine to register tx4938ide driver and use it on
RBTX4938 board.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>