OSDN Git Service
Leon Romanovsky [Tue, 24 Jan 2023 11:54:58 +0000 (13:54 +0200)]
net/mlx5e: Fill IPsec policy validation failure reason
Rely on extack to return failure reason.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Leon Romanovsky [Tue, 24 Jan 2023 11:54:57 +0000 (13:54 +0200)]
xfrm: extend add policy callback to set failure reason
Almost all validation logic is in the drivers, but they are
missing reliable way to convey failure reason to userspace
applications.
Let's use extack to return this information to users.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean [Wed, 25 Jan 2023 11:02:14 +0000 (13:02 +0200)]
net: ethtool: provide shims for stats aggregation helpers when CONFIG_ETHTOOL_NETLINK=n
ethtool_aggregate_*_stats() are implemented in net/ethtool/stats.c, a
file which is compiled out when CONFIG_ETHTOOL_NETLINK=n. In order to
avoid adding Kbuild dependencies from drivers (which call these helpers)
on CONFIG_ETHTOOL_NETLINK, let's add some shim definitions which simply
make the helpers dead code.
This means the function prototypes should have been located in
include/linux/ethtool_netlink.h rather than include/linux/ethtool.h.
Fixes:
449c5459641a ("net: ethtool: add helpers for aggregate statistics")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230125110214.4127759-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Paolo Abeni [Thu, 26 Jan 2023 12:33:32 +0000 (13:33 +0100)]
Merge branch 'mptcp-add-mixed-v4-v6-support-for-the-in-kernel-pm'
Matthieu Baerts says:
====================
mptcp: add mixed v4/v6 support for the in-kernel PM
Before these patches, the in-kernel Path-Manager would not allow, for
the same MPTCP connection, having a mix of subflows in v4 and v6.
MPTCP's RFC 8684 doesn't forbid that and it is even recommended to do so
as the path in v4 and v6 are likely different. Some networks are also
v4 or v6 only, we cannot assume they all have both v4 and v6 support.
Patch 1 then removes this artificial constraint in the in-kernel PM
currently enforcing there are no mixed subflows in place, either in
address announcement or in subflow creation areas.
Patch 2 makes sure the sk_ipv6only attribute is also propagated to
subflows, just in case a new PM wouldn't respect it.
Some selftests have also been added for the in-kernel PM (patch 3).
Patches 4 to 8 are just some cleanups and small improvements in the
printed messages in the userspace PM. It is not linked to the rest but
identified when working on a related patch modifying this selftest,
already in -net:
commit
4656d72c1efa ("selftests: mptcp: userspace: validate v4-v6 subflows mix")
---
====================
Link: https://lore.kernel.org/r/20230123-upstream-net-next-pm-v4-v6-v1-0-43fac502bfbf@tessares.net
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Matthieu Baerts [Wed, 25 Jan 2023 10:47:28 +0000 (11:47 +0100)]
selftests: mptcp: userspace: avoid read errors
During the cleanup phase, the server pids were killed with a SIGTERM
directly, not using a SIGUSR1 first to quit safely. As a result, this
test was often ending with two error messages:
read: Connection reset by peer
While at it, use a for-loop to terminate all the PIDs the same way.
Also the different files are now removed after having killed the PIDs
using them. It makes more sense to do that in this order.
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Matthieu Baerts [Wed, 25 Jan 2023 10:47:27 +0000 (11:47 +0100)]
selftests: mptcp: userspace: print error details if any
Before, only '[FAIL]' was printed in case of error during the validation
phase.
Now, in case of failure, the variable name, its value and expected one
are displayed to help understand what was wrong.
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Matthieu Baerts [Wed, 25 Jan 2023 10:47:26 +0000 (11:47 +0100)]
selftests: mptcp: userspace: refactor asserts
Instead of having a long list of conditions to check, it is possible to
give a list of variable names to compare with their 'e_XXX' version.
This will ease the introduction of the following commit which will print
which condition has failed (if any).
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Matthieu Baerts [Wed, 25 Jan 2023 10:47:25 +0000 (11:47 +0100)]
selftests: mptcp: userspace: print titles
This script is running a few tests after having setup the environment.
Printing titles helps understand what is being tested.
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Matthieu Baerts [Wed, 25 Jan 2023 10:47:24 +0000 (11:47 +0100)]
mptcp: userspace pm: use a single point of exit
Like in all other functions in this file, a single point of exit is used
when extra operations are needed: unlock, decrement refcount, etc.
There is no functional change for the moment but it is better to do the
same here to make sure all cleanups are done in case of intermediate
errors.
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Paolo Abeni [Wed, 25 Jan 2023 10:47:23 +0000 (11:47 +0100)]
selftests: mptcp: add test-cases for mixed v4/v6 subflows
Note that we can't guess the listener family anymore based on the client
target address: always use IPv6.
The fullmesh flag with endpoints from different families is also
validated here.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Matthieu Baerts [Wed, 25 Jan 2023 10:47:22 +0000 (11:47 +0100)]
mptcp: propagate sk_ipv6only to subflows
Usually, attributes are propagated to subflows as well.
Here, if subflows are created by other ways than the MPTCP path-manager,
it is important to make sure they are in v6 if it is asked by the
userspace.
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Paolo Abeni [Wed, 25 Jan 2023 10:47:21 +0000 (11:47 +0100)]
mptcp: let the in-kernel PM use mixed IPv4 and IPv6 addresses
Currently the in-kernel PM arbitrary enforces that created subflow's
family must match the main MPTCP socket while the RFC allows mixing
IPv4 and IPv6 subflows.
This patch changes the in-kernel PM logic to create subflows matching
the currently selected source (or destination) address. IPv4 sockets
can pick only IPv4 addresses (and v4 mapped in v6), while IPv6 sockets
not restricted to V6ONLY can pick either IPv4 and IPv6 addresses as
long as the source and destination matches.
A helper, previously introduced is used to ease family matching checks,
taking care of IPv4 vs IPv4-mapped-IPv6 vs IPv6 only addresses.
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/269
Co-developed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Jamie Bainbridge [Wed, 25 Jan 2023 00:16:52 +0000 (11:16 +1100)]
icmp: Add counters for rate limits
There are multiple ICMP rate limiting mechanisms:
* Global limits: net.ipv4.icmp_msgs_burst/icmp_msgs_per_sec
* v4 per-host limits: net.ipv4.icmp_ratelimit/ratemask
* v6 per-host limits: net.ipv6.icmp_ratelimit/ratemask
However, when ICMP output is limited, there is no way to tell
which limit has been hit or even if the limits are responsible
for the lack of ICMP output.
Add counters for each of the cases above. As we are within
local_bh_disable(), use the __INC stats variant.
Example output:
# nstat -sz "*RateLimit*"
IcmpOutRateLimitGlobal 134 0.0
IcmpOutRateLimitHost 770 0.0
Icmp6OutRateLimitHost 84 0.0
Signed-off-by: Jamie Bainbridge <jamie.bainbridge@gmail.com>
Suggested-by: Abhishek Rawal <rawal.abhishek92@gmail.com>
Link: https://lore.kernel.org/r/273b32241e6b7fdc5c609e6f5ebc68caf3994342.1674605770.git.jamie.bainbridge@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Paolo Abeni [Thu, 26 Jan 2023 09:08:05 +0000 (10:08 +0100)]
Merge branch 'adding-sparx5-is0-vcap-support'
Steen Hegelund says:
====================
Adding Sparx5 IS0 VCAP support
This provides the Ingress Stage 0 (IS0) VCAP (Versatile Content-Aware
Processor) support for the Sparx5 platform.
The IS0 VCAP (also known in the datasheet as CLM) is a classifier VCAP that
mainly extracts frame information to metadata that follows the frame in the
Sparx5 processing flow all the way to the egress port.
The IS0 VCAP has 4 lookups and they are accessible with a TC chain id:
- chain
1000000: IS0 Lookup 0
- chain
1100000: IS0 Lookup 1
- chain
1200000: IS0 Lookup 2
- chain
1300000: IS0 Lookup 3
- chain
1400000: IS0 Lookup 4
- chain
1500000: IS0 Lookup 5
Each of these lookups have their own port keyset configuration that decides
which keys will be used for matching on which traffic type.
The IS0 VCAP has these traffic classifications:
- IPv4 frames
- IPv6 frames
- Unicast MPLS frames (ethertype = 0x8847)
- Multicast MPLS frames (ethertype = 0x8847)
- Other frame types than MPLS, IPv4 and IPv6
The IS0 VCAP has an action that allows setting the value of a PAG (Policy
Association Group) key field in the frame metadata, and this can be used
for matching in an IS2 VCAP rule.
This allow rules in the IS0 VCAP to be linked to rules in the IS2 VCAP.
The linking is exposed by using the TC "goto chain" action with an offset
from the IS2 chain ids.
As an example a "goto chain
8000001" will use a PAG value of 1 to chain to
a rule in IS2 Lookup 0.
====================
Link: https://lore.kernel.org/r/20230124104511.293938-1-steen.hegelund@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Steen Hegelund [Tue, 24 Jan 2023 10:45:11 +0000 (11:45 +0100)]
net: microchip: sparx5: Add support for IS0 VCAP CVLAN TC keys
This adds support for parsing and matching on the CVLAN tags in the Sparx5
IS0 VCAP.
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Steen Hegelund [Tue, 24 Jan 2023 10:45:10 +0000 (11:45 +0100)]
net: microchip: sparx5: Add support for IS0 VCAP ethernet protocol types
This allows the IS0 VCAP to have its own list of supported ethernet
protocol types matching what is supported by the VCAPs port lookup
classification.
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Steen Hegelund [Tue, 24 Jan 2023 10:45:09 +0000 (11:45 +0100)]
net: microchip: sparx5: Add automatic selection of VCAP rule actionset
With more than one possible actionset in a VCAP instance, the VCAP API will
now use the actions in a VCAP rule to select the actionset that fits these
actions the best possible way.
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Steen Hegelund [Tue, 24 Jan 2023 10:45:08 +0000 (11:45 +0100)]
net: microchip: sparx5: Add TC filter chaining support for IS0 and IS2 VCAPs
This allows rules to be chained between VCAP instances, e.g. from IS0
Lookup 0 to IS0 Lookup 1, or from one of the IS0 Lookups to one of the IS2
Lookups.
Chaining from an IS2 Lookup to another IS2 Lookup is not supported in the
hardware.
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Steen Hegelund [Tue, 24 Jan 2023 10:45:07 +0000 (11:45 +0100)]
net: microchip: sparx5: Add TC support for IS0 VCAP
This enables the TC command to use the Sparx5 IS0 VCAP
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Steen Hegelund [Tue, 24 Jan 2023 10:45:06 +0000 (11:45 +0100)]
net: microchip: sparx5: Add actionset type id information to rule
This adds the actionset type id to the rule information. This is needed as
we now have more than one actionset in a VCAP instance (IS0).
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Steen Hegelund [Tue, 24 Jan 2023 10:45:05 +0000 (11:45 +0100)]
net: microchip: sparx5: Add IS0 VCAP keyset configuration for Sparx5
This adds the IS0 VCAP port keyset configuration for Sparx5 and also
updates the debugFS support to show the keyset configuration.
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Steen Hegelund [Tue, 24 Jan 2023 10:45:04 +0000 (11:45 +0100)]
net: microchip: sparx5: Add IS0 VCAP model and updated KUNIT VCAP model
This provides the IS0 (Ingress Stage 0) or CLM VCAP model for Sparx5.
This VCAP provides classification actions for Sparx5.
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Jakub Kicinski [Thu, 26 Jan 2023 06:45:02 +0000 (22:45 -0800)]
Merge branch 'add-ip_local_port_range-socket-option'
Jakub Sitnicki says:
====================
Add IP_LOCAL_PORT_RANGE socket option
This patch set is a follow up to the "How to share IPv4 addresses by
partitioning the port space" talk given at LPC 2022 [1].
Please see patch #1 for the motivation & the use case description.
Patch #2 adds tests exercising the new option in various scenarios.
Documentation
-------------
Proposed update to the ip(7) man-page:
IP_LOCAL_PORT_RANGE (since Linux X.Y)
Set or get the per-socket default local port range. This
option can be used to clamp down the global local port
range, defined by the ip_local_port_range /proc interface
described below, for a given socket.
The option takes an uint32_t value with the high 16 bits
set to the upper range bound, and the low 16 bits set to
the lower range bound. Range bounds are inclusive. The
16-bit values should be in host byte order.
The lower bound has to be less than the upper bound when
both bounds are not zero. Otherwise, setting the option
fails with EINVAL.
If either bound is outside of the global local port range,
or is zero, then that bound has no effect.
To reset the setting, pass zero as both the upper and the
lower bound.
Interaction with SELinux bind() hook
------------------------------------
SELinux bind() hook - selinux_socket_bind() - performs a permission check
if the requested local port number lies outside of the netns ephemeral port
range.
The proposed socket option cannot be used change the ephemeral port range
to extend beyond the per-netns port range, as set by
net.ipv4.ip_local_port_range.
Hence, there is no interaction with SELinux, AFAICT.
RFC -> v1
RFC: https://lore.kernel.org/netdev/
20220912225308.93659-1-jakub@cloudflare.com/
* Allow either the high bound or the low bound, or both, to be zero
* Add getsockopt support
* Add selftests
Links:
------
[1]: https://lpc.events/event/16/contributions/1349/
====================
Link: https://lore.kernel.org/r/20221221-sockopt-port-range-v6-0-be255cc0e51f@cloudflare.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Sitnicki [Tue, 24 Jan 2023 13:36:44 +0000 (14:36 +0100)]
selftests/net: Cover the IP_LOCAL_PORT_RANGE socket option
Exercise IP_LOCAL_PORT_RANGE socket option in various scenarios:
1. pass invalid values to setsockopt
2. pass a range outside of the per-netns port range
3. configure a single-port range
4. exhaust a configured multi-port range
5. check interaction with late-bind (IP_BIND_ADDRESS_NO_PORT)
6. set then get the per-socket port range
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Sitnicki [Tue, 24 Jan 2023 13:36:43 +0000 (14:36 +0100)]
inet: Add IP_LOCAL_PORT_RANGE socket option
Users who want to share a single public IP address for outgoing connections
between several hosts traditionally reach for SNAT. However, SNAT requires
state keeping on the node(s) performing the NAT.
A stateless alternative exists, where a single IP address used for egress
can be shared between several hosts by partitioning the available ephemeral
port range. In such a setup:
1. Each host gets assigned a disjoint range of ephemeral ports.
2. Applications open connections from the host-assigned port range.
3. Return traffic gets routed to the host based on both, the destination IP
and the destination port.
An application which wants to open an outgoing connection (connect) from a
given port range today can choose between two solutions:
1. Manually pick the source port by bind()'ing to it before connect()'ing
the socket.
This approach has a couple of downsides:
a) Search for a free port has to be implemented in the user-space. If
the chosen 4-tuple happens to be busy, the application needs to retry
from a different local port number.
Detecting if 4-tuple is busy can be either easy (TCP) or hard
(UDP). In TCP case, the application simply has to check if connect()
returned an error (EADDRNOTAVAIL). That is assuming that the local
port sharing was enabled (REUSEADDR) by all the sockets.
# Assume desired local port range is 60_000-60_511
s = socket(AF_INET, SOCK_STREAM)
s.setsockopt(SOL_SOCKET, SO_REUSEADDR, 1)
s.bind(("192.0.2.1", 60_000))
s.connect(("1.1.1.1", 53))
# Fails only if 192.0.2.1:60000 -> 1.1.1.1:53 is busy
# Application must retry with another local port
In case of UDP, the network stack allows binding more than one socket
to the same 4-tuple, when local port sharing is enabled
(REUSEADDR). Hence detecting the conflict is much harder and involves
querying sock_diag and toggling the REUSEADDR flag [1].
b) For TCP, bind()-ing to a port within the ephemeral port range means
that no connecting sockets, that is those which leave it to the
network stack to find a free local port at connect() time, can use
the this port.
IOW, the bind hash bucket tb->fastreuse will be 0 or 1, and the port
will be skipped during the free port search at connect() time.
2. Isolate the app in a dedicated netns and use the use the per-netns
ip_local_port_range sysctl to adjust the ephemeral port range bounds.
The per-netns setting affects all sockets, so this approach can be used
only if:
- there is just one egress IP address, or
- the desired egress port range is the same for all egress IP addresses
used by the application.
For TCP, this approach avoids the downsides of (1). Free port search and
4-tuple conflict detection is done by the network stack:
system("sysctl -w net.ipv4.ip_local_port_range='60000 60511'")
s = socket(AF_INET, SOCK_STREAM)
s.setsockopt(SOL_IP, IP_BIND_ADDRESS_NO_PORT, 1)
s.bind(("192.0.2.1", 0))
s.connect(("1.1.1.1", 53))
# Fails if all 4-tuples 192.0.2.1:60000-60511 -> 1.1.1.1:53 are busy
For UDP this approach has limited applicability. Setting the
IP_BIND_ADDRESS_NO_PORT socket option does not result in local source
port being shared with other connected UDP sockets.
Hence relying on the network stack to find a free source port, limits the
number of outgoing UDP flows from a single IP address down to the number
of available ephemeral ports.
To put it another way, partitioning the ephemeral port range between hosts
using the existing Linux networking API is cumbersome.
To address this use case, add a new socket option at the SOL_IP level,
named IP_LOCAL_PORT_RANGE. The new option can be used to clamp down the
ephemeral port range for each socket individually.
The option can be used only to narrow down the per-netns local port
range. If the per-socket range lies outside of the per-netns range, the
latter takes precedence.
UAPI-wise, the low and high range bounds are passed to the kernel as a pair
of u16 values in host byte order packed into a u32. This avoids pointer
passing.
PORT_LO = 40_000
PORT_HI = 40_511
s = socket(AF_INET, SOCK_STREAM)
v = struct.pack("I", PORT_HI << 16 | PORT_LO)
s.setsockopt(SOL_IP, IP_LOCAL_PORT_RANGE, v)
s.bind(("127.0.0.1", 0))
s.getsockname()
# Local address between ("127.0.0.1", 40_000) and ("127.0.0.1", 40_511),
# if there is a free port. EADDRINUSE otherwise.
[1] https://github.com/cloudflare/cloudflare-blog/blob/
232b432c1d57/2022-02-connectx/connectx.py#L116
Reviewed-by: Marek Majkowski <marek@cloudflare.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Randy Dunlap [Tue, 24 Jan 2023 18:17:24 +0000 (10:17 -0800)]
net: Kconfig: fix spellos
Fix spelling in net/ Kconfig files.
(reported by codespell)
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Cc: Jozsef Kadlecsik <kadlec@netfilter.org>
Cc: Florian Westphal <fw@strlen.de>
Cc: coreteam@netfilter.org
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Link: https://lore.kernel.org/r/20230124181724.18166-1-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean [Tue, 24 Jan 2023 11:13:28 +0000 (13:13 +0200)]
net: ethtool: fix NULL pointer dereference in pause_prepare_data()
In the following call path:
ethnl_default_dumpit
-> ethnl_default_dump_one
-> ctx->ops->prepare_data
-> pause_prepare_data
struct genl_info *info will be passed as NULL, and pause_prepare_data()
dereferences it while getting the extended ack pointer.
To avoid that, just set the extack to NULL if "info" is NULL, since the
netlink extack handling messages know how to deal with that.
The pattern "info ? info->extack : NULL" is present in quite a few other
"prepare_data" implementations, so it's clear that it's a more general
problem to be dealt with at a higher level, but the code should have at
least adhered to the current conventions to avoid the NULL dereference.
Fixes:
04692c9020b7 ("net: ethtool: netlink: retrieve stats from multiple sources (eMAC, pMAC)")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reported-by: syzbot+9d44aae2720fc40b8474@syzkaller.appspotmail.com
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Tue, 24 Jan 2023 11:08:01 +0000 (13:08 +0200)]
net: ethtool: fix NULL pointer dereference in stats_prepare_data()
In the following call path:
ethnl_default_dumpit
-> ethnl_default_dump_one
-> ctx->ops->prepare_data
-> stats_prepare_data
struct genl_info *info will be passed as NULL, and stats_prepare_data()
dereferences it while getting the extended ack pointer.
To avoid that, just set the extack to NULL if "info" is NULL, since the
netlink extack handling messages know how to deal with that.
The pattern "info ? info->extack : NULL" is present in quite a few other
"prepare_data" implementations, so it's clear that it's a more general
problem to be dealt with at a higher level, but the code should have at
least adhered to the current conventions to avoid the NULL dereference.
Fixes:
04692c9020b7 ("net: ethtool: netlink: retrieve stats from multiple sources (eMAC, pMAC)")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Wed, 25 Jan 2023 09:46:49 +0000 (09:46 +0000)]
Merge branch 's390-ism-generalized-interface'
Jan Karcher says:
====================
drivers/s390/net/ism: Add generalized interface
Previously, there was no clean separation between SMC-D code and the ISM
device driver.This patch series addresses the situation to make ISM available
for uses outside of SMC-D.
In detail: SMC-D offers an interface via struct smcd_ops, which only the
ISM module implements so far. However, there is no real separation between
the smcd and ism modules, which starts right with the ISM device
initialization, which calls directly into the SMC-D code.
This patch series introduces a new API in the ISM module, which allows
registration of arbitrary clients via include/linux/ism.h: struct ism_client.
Furthermore, it introduces a "pure" struct ism_dev (i.e. getting rid of
dependencies on SMC-D in the device structure), and adds a number of API
calls for data transfers via ISM (see ism_register_dmb() & friends).
Still, the ISM module implements the SMC-D API, and therefore has a number
of internal helper functions for that matter.
Note that the ISM API is consciously kept thin for now (as compared to the
SMC-D API calls), as a number of API calls are only used with SMC-D and
hardly have any meaningful usage beyond SMC-D, e.g. the VLAN-related calls.
v1 -> v2:
Removed s390x dependency which broke config for other archs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Raspl [Mon, 23 Jan 2023 18:17:52 +0000 (19:17 +0100)]
net/smc: De-tangle ism and smc device initialization
The struct device for ISM devices was part of struct smcd_dev. Move to
struct ism_dev, provide a new API call in struct smcd_ops, and convert
existing SMCD code accordingly.
Furthermore, remove struct smcd_dev from struct ism_dev.
This is the final part of a bigger overhaul of the interfaces between SMC
and ISM.
Signed-off-by: Stefan Raspl <raspl@linux.ibm.com>
Signed-off-by: Jan Karcher <jaka@linux.ibm.com>
Signed-off-by: Wenjia Zhang <wenjia@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Raspl [Mon, 23 Jan 2023 18:17:51 +0000 (19:17 +0100)]
s390/ism: Consolidate SMC-D-related code
The ism module had SMC-D-specific code sprinkled across the entire module.
We are now consolidating the SMC-D-specific parts into the latter parts
of the module, so it becomes more clear what code is intended for use with
ISM, and which parts are glue code for usage in the context of SMC-D.
This is the fourth part of a bigger overhaul of the interfaces between SMC
and ISM.
Signed-off-by: Stefan Raspl <raspl@linux.ibm.com>
Signed-off-by: Jan Karcher <jaka@linux.ibm.com>
Signed-off-by: Wenjia Zhang <wenjia@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Raspl [Mon, 23 Jan 2023 18:17:50 +0000 (19:17 +0100)]
net/smc: Separate SMC-D and ISM APIs
We separate the code implementing the struct smcd_ops API in the ISM
device driver from the functions that may be used by other exploiters of
ISM devices.
Note: We start out small, and don't offer the whole breadth of the ISM
device for public use, as many functions are specific to or likely only
ever used in the context of SMC-D.
This is the third part of a bigger overhaul of the interfaces between SMC
and ISM.
Signed-off-by: Stefan Raspl <raspl@linux.ibm.com>
Signed-off-by: Jan Karcher <jaka@linux.ibm.com>
Signed-off-by: Wenjia Zhang <wenjia@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Raspl [Mon, 23 Jan 2023 18:17:49 +0000 (19:17 +0100)]
net/smc: Register SMC-D as ISM client
Register the smc module with the new ism device driver API.
This is the second part of a bigger overhaul of the interfaces between SMC
and ISM.
Signed-off-by: Stefan Raspl <raspl@linux.ibm.com>
Signed-off-by: Jan Karcher <jaka@linux.ibm.com>
Signed-off-by: Wenjia Zhang <wenjia@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Raspl [Mon, 23 Jan 2023 18:17:48 +0000 (19:17 +0100)]
net/ism: Add new API for client registration
Add a new API that allows other drivers to concurrently access ISM devices.
To do so, we introduce a new API that allows other modules to register for
ISM device usage. Furthermore, we move the GID to struct ism, where it
belongs conceptually, and rename and relocate struct smcd_event to struct
ism_event.
This is the first part of a bigger overhaul of the interfaces between SMC
and ISM.
Signed-off-by: Stefan Raspl <raspl@linux.ibm.com>
Signed-off-by: Jan Karcher <jaka@linux.ibm.com>
Signed-off-by: Wenjia Zhang <wenjia@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Raspl [Mon, 23 Jan 2023 18:17:47 +0000 (19:17 +0100)]
s390/ism: Introduce struct ism_dmb
Conceptually, a DMB is a structure that belongs to ISM devices. However,
SMC currently 'owns' this structure. So future exploiters of ISM devices
would be forced to include SMC headers to work - which is just weird.
Therefore, we switch ISM to struct ism_dmb, introduce a new public header
with the definition (will be populated with further API calls later on),
and, add a thin wrapper to please SMC. Since structs smcd_dmb and ism_dmb
are identical, we can simply convert between the two for now.
Signed-off-by: Stefan Raspl <raspl@linux.ibm.com>
Signed-off-by: Jan Karcher <jaka@linux.ibm.com>
Signed-off-by: Wenjia Zhang <wenjia@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Raspl [Mon, 23 Jan 2023 18:17:46 +0000 (19:17 +0100)]
net/ism: Add missing calls to disable bus-mastering
Signed-off-by: Stefan Raspl <raspl@linux.ibm.com>
Signed-off-by: Jan Karcher <jaka@linux.ibm.com>
Signed-off-by: Wenjia Zhang <wenjia@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Raspl [Mon, 23 Jan 2023 18:17:45 +0000 (19:17 +0100)]
net/smc: Terminate connections prior to device removal
Removing an ISM device prior to terminating its associated connections
doesn't end well.
Signed-off-by: Stefan Raspl <raspl@linux.ibm.com>
Signed-off-by: Jan Karcher <jaka@linux.ibm.com>
Signed-off-by: Wenjia Zhang <wenjia@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Parav Pandit [Mon, 23 Jan 2023 03:55:11 +0000 (05:55 +0200)]
virtio-net: Reduce debug name field size to 16 bytes
virtio queue index can be maximum of 65535. 16 bytes are enough to store
the vq name with the existing string prefix.
With this change, send queue struct saves 24 bytes and receive
queue saves whole cache line worth 64 bytes per structure
due to saving in alignment bytes.
Pahole results before:
pahole -s drivers/net/virtio_net.o | \
grep -e "send_queue" -e "receive_queue"
send_queue 1112 0
receive_queue 1280 1
Pahole results after:
pahole -s drivers/net/virtio_net.o | \
grep -e "send_queue" -e "receive_queue"
send_queue 1088 0
receive_queue 1216 1
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Tue, 24 Jan 2023 03:52:31 +0000 (19:52 -0800)]
devlink: remove a dubious assumption in fmsg dumping
Build bot detects that err may be returned uninitialized in
devlink_fmsg_prepare_skb(). This is not really true because
all fmsgs users should create at least one outer nest, and
therefore fmsg can't be completely empty.
That said the assumption is not trivial to confirm, so let's
follow the bots advice, anyway.
This code does not seem to have changed since its inception in
commit
1db64e8733f6 ("devlink: Add devlink formatted message (fmsg) API")
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20230124035231.787381-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean [Mon, 23 Jan 2023 18:45:38 +0000 (20:45 +0200)]
net: mscc: ocelot: fix incorrect verify_enabled reporting in ethtool get_mm()
We don't read the verify_enabled variable from hardware in the MAC Merge
layer state GET operation, instead we always leave it set to "false".
The user may think something is wrong if they set verify_enabled to
true, then read it back and see it's still false, even though the
configuration took place.
Fixes:
6505b6805655 ("net: mscc: ocelot: add MAC Merge layer support for VSC9959")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20230123184538.3420098-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
James Hershaw [Mon, 23 Jan 2023 13:41:35 +0000 (14:41 +0100)]
nfp: flower: change get/set_eeprom logic and enable for flower reps
The changes in this patch are as follows:
- Alter the logic of get/set_eeprom functions to use the helper function
nfp_app_from_netdev() which handles differentiating between an nfp_net
and a nfp_repr. This allows us to get an agnostic backpointer to the
pdev.
- Enable the various eeprom commands by adding the 'get_eeprom_len',
'get_eeprom', 'set_eeprom' callbacks to the nfp_port_ethtool_ops struct.
This allows the eeprom commands to work on representor interfaces,
similar to a previous patch which added it to the vnics.
Currently these are being used to configure persistent MAC addresses for
the physical ports on the nfp.
Signed-off-by: James Hershaw <james.hershaw@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230123134135.293278-1-simon.horman@corigine.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Guillaume Nault [Mon, 23 Jan 2023 17:47:09 +0000 (18:47 +0100)]
ipv6: Make ip6_route_output_flags_noref() static.
This function is only used in net/ipv6/route.c and has no reason to be
visible outside of it.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/50706db7f675e40b3594d62011d9363dce32b92e.1674495822.git.gnault@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Mon, 23 Jan 2023 22:22:24 +0000 (14:22 -0800)]
netlink: fix spelling mistake in dump size assert
Commit
2c7bc10d0f7b ("netlink: add macro for checking dump ctx size")
misspelled the name of the assert as asset, missing an R.
Reported-by: Ido Schimmel <idosch@idosch.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/r/20230123222224.732338-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Paolo Abeni [Tue, 24 Jan 2023 10:02:03 +0000 (11:02 +0100)]
Merge branch 'netlink-protocol-specs'
Jakub Kicinski says:
====================
Netlink protocol specs
I think the Netlink proto specs are far along enough to merge.
Filling in all attribute types and quirks will be an ongoing
effort but we have enough to cover FOU so it's somewhat complete.
I fully intend to continue polishing the code but at the same
time I'd like to start helping others base their work on the
specs (e.g. DPLL) and need to start working on some new families
myself.
That's the progress / motivation for merging. The RFC [1] has more
of a high level blurb, plus I created a lot of documentation, I'm
not going to repeat it here. There was also the talk at LPC [2].
[1] https://lore.kernel.org/all/
20220811022304.583300-1-kuba@kernel.org/
[2] https://youtu.be/9QkXIQXkaQk?t=2562
v2: https://lore.kernel.org/all/
20220930023418.
1346263-1-kuba@kernel.org/
v3: https://lore.kernel.org/all/
20230119003613.111778-1-kuba@kernel.org/1
v4:
- spec improvements (patch 2)
- Python cleanup (patch 3)
- rename auto-gen files and use the right comment style
====================
Link: https://lore.kernel.org/r/20230120175041.342573-1-kuba@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Jakub Kicinski [Fri, 20 Jan 2023 17:50:41 +0000 (09:50 -0800)]
tools: ynl: add a completely generic client
Add a CLI sample which can take in arbitrary request
in JSON format, convert it to Netlink and do the inverse
for output.
It's meant as a development tool primarily and perhaps
for selftests which need to tickle netlink in a special way.
Acked-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Jakub Kicinski [Fri, 20 Jan 2023 17:50:40 +0000 (09:50 -0800)]
net: fou: use policy and operation tables generated from the spec
Generate and plug in the spec-based tables.
A little bit of renaming is needed in the FOU code.
Acked-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Jakub Kicinski [Fri, 20 Jan 2023 17:50:39 +0000 (09:50 -0800)]
net: fou: rename the source for linking
We'll need to link two objects together to form the fou module.
This means the source can't be called fou, the build system expects
fou.o to be the combined object.
Acked-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Jakub Kicinski [Fri, 20 Jan 2023 17:50:38 +0000 (09:50 -0800)]
net: fou: regenerate the uAPI from the spec
Regenerate the FOU uAPI header from the YAML spec.
The flags now come before attributes which use them,
and the comments for type disappear (coders should look
at the spec instead).
Acked-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Jakub Kicinski [Fri, 20 Jan 2023 17:50:37 +0000 (09:50 -0800)]
netlink: add a proto specification for FOU
FOU has a reasonably modern Genetlink family. Add a spec.
Acked-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Jakub Kicinski [Fri, 20 Jan 2023 17:50:36 +0000 (09:50 -0800)]
net: add basic C code generators for Netlink
Code generators to turn Netlink specs into C code.
I'm definitely not proud of it.
The main generator is in Python, there's a bash script
to regen all code-gen'ed files in tree after making
spec changes.
Acked-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Jakub Kicinski [Fri, 20 Jan 2023 17:50:35 +0000 (09:50 -0800)]
netlink: add schemas for YAML specs
Add schemas for Netlink spec files. As described in the docs
we have 4 "protocols" or compatibility levels, and each one
comes with its own schema, but the more general / legacy
schemas are superset of more modern ones: genetlink is
the smallest followed by genetlink-c and genetlink-legacy.
There is no schema for raw netlink, yet, I haven't found the time..
I don't know enough jsonschema to do inheritance or something
but the repetition is not too bad. I hope.
Acked-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Jakub Kicinski [Fri, 20 Jan 2023 17:50:34 +0000 (09:50 -0800)]
docs: add more netlink docs (incl. spec docs)
Add documentation about the upcoming Netlink protocol specs.
Reviewed-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: Bagas Sanjaya <bagasdotme@gmail.com>
Acked-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Paolo Abeni [Tue, 24 Jan 2023 09:30:56 +0000 (10:30 +0100)]
Merge branch 'net-sched-use-the-backlog-for-nested-mirred-ingress'
Davide Caratti says:
====================
net/sched: use the backlog for nested mirred ingress
TC mirred has a protection against excessive stack growth, but that
protection doesn't really guarantee the absence of recursion, nor
it guards against loops. Patch 1/2 rewords "recursion" to "nesting" to
make this more clear.
We can leverage on this existing mechanism to prevent TCP / SCTP from doing
soft lock-up in some specific scenarios that uses mirred egress->ingress:
patch 2 changes mirred so that the networking backlog is used for nested
mirred ingress actions.
====================
Link: https://lore.kernel.org/r/cover.1674233458.git.dcaratti@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Davide Caratti [Fri, 20 Jan 2023 17:01:40 +0000 (18:01 +0100)]
act_mirred: use the backlog for nested calls to mirred ingress
William reports kernel soft-lockups on some OVS topologies when TC mirred
egress->ingress action is hit by local TCP traffic [1].
The same can also be reproduced with SCTP (thanks Xin for verifying), when
client and server reach themselves through mirred egress to ingress, and
one of the two peers sends a "heartbeat" packet (from within a timer).
Enqueueing to backlog proved to fix this soft lockup; however, as Cong
noticed [2], we should preserve - when possible - the current mirred
behavior that counts as "overlimits" any eventual packet drop subsequent to
the mirred forwarding action [3]. A compromise solution might use the
backlog only when tcf_mirred_act() has a nest level greater than one:
change tcf_mirred_forward() accordingly.
Also, add a kselftest that can reproduce the lockup and verifies TC mirred
ability to account for further packet drops after TC mirred egress->ingress
(when the nest level is 1).
[1] https://lore.kernel.org/netdev/
33dc43f587ec1388ba456b4915c75f02a8aae226.
1663945716.git.dcaratti@redhat.com/
[2] https://lore.kernel.org/netdev/Y0w%2FWWY60gqrtGLp@pop-os.localdomain/
[3] such behavior is not guaranteed: for example, if RPS or skb RX
timestamping is enabled on the mirred target device, the kernel
can defer receiving the skb and return NET_RX_SUCCESS inside
tcf_mirred_forward().
Reported-by: William Zhao <wizhao@redhat.com>
CC: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Davide Caratti [Fri, 20 Jan 2023 17:01:39 +0000 (18:01 +0100)]
net/sched: act_mirred: better wording on protection against excessive stack growth
with commit
e2ca070f89ec ("net: sched: protect against stack overflow in
TC act_mirred"), act_mirred protected itself against excessive stack growth
using per_cpu counter of nested calls to tcf_mirred_act(), and capping it
to MIRRED_RECURSION_LIMIT. However, such protection does not detect
recursion/loops in case the packet is enqueued to the backlog (for example,
when the mirred target device has RPS or skb timestamping enabled). Change
the wording from "recursion" to "nesting" to make it more clear to readers.
CC: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Paolo Abeni [Tue, 24 Jan 2023 09:08:53 +0000 (10:08 +0100)]
Merge branch 'fix-cpts-release-action-in-am65-cpts-driver'
Siddharth Vadapalli says:
====================
Fix CPTS release action in am65-cpts driver
Delete unreachable code in am65_cpsw_init_cpts() function, which was
Reported-by: Leon Romanovsky <leon@kernel.org>
at:
https://lore.kernel.org/r/Y8aHwSnVK9+sAb24@unreal
Remove the devm action associated with am65_cpts_release() and invoke the
function directly on the cleanup and exit paths.
v4:
https://lore.kernel.org/r/
20230120044201.357950-1-s-vadapalli@ti.com/
v3:
https://lore.kernel.org/r/
20230118095439.114222-1-s-vadapalli@ti.com/
v2:
https://lore.kernel.org/r/
20230116044517.310461-1-s-vadapalli@ti.com/
v1:
https://lore.kernel.org/r/
20230113104816.132815-1-s-vadapalli@ti.com/
====================
Link: https://lore.kernel.org/r/20230120070731.383729-1-s-vadapalli@ti.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Siddharth Vadapalli [Fri, 20 Jan 2023 07:07:31 +0000 (12:37 +0530)]
net: ethernet: ti: am65-cpsw/cpts: Fix CPTS release action
The am65_cpts_release() function is registered as a devm_action in the
am65_cpts_create() function in am65-cpts driver. When the am65-cpsw driver
invokes am65_cpts_create(), am65_cpts_release() is added in the set of devm
actions associated with the am65-cpsw driver's device.
In the event of probe failure or probe deferral, the platform_drv_probe()
function invokes dev_pm_domain_detach() which powers off the CPSW and the
CPSW's CPTS hardware, both of which share the same power domain. Since the
am65_cpts_disable() function invoked by the am65_cpts_release() function
attempts to reset the CPTS hardware by writing to its registers, the CPTS
hardware is assumed to be powered on at this point. However, the hardware
is powered off before the devm actions are executed.
Fix this by getting rid of the devm action for am65_cpts_release() and
invoking it directly on the cleanup and exit paths.
Fixes:
f6bd59526ca5 ("net: ethernet: ti: introduce am654 common platform time sync driver")
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Siddharth Vadapalli [Fri, 20 Jan 2023 07:07:30 +0000 (12:37 +0530)]
net: ethernet: ti: am65-cpsw: Delete unreachable error handling code
The am65_cpts_create() function returns -EOPNOTSUPP only when the config
"CONFIG_TI_K3_AM65_CPTS" is disabled. Also, in the am65_cpsw_init_cpts()
function, am65_cpts_create() can only be invoked if the config
"CONFIG_TI_K3_AM65_CPTS" is enabled. Thus, the error handling code for the
case in which the return value of am65_cpts_create() is -EOPNOTSUPP, is
unreachable. Hence delete it.
Reported-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Rakesh Sankaranarayanan [Fri, 20 Jan 2023 10:47:33 +0000 (16:17 +0530)]
net: phy: microchip: run phy initialization during each link update
PHY initialization is supposed to run on every mode changes.
"lan87xx_config_aneg()" verifies every mode change using
"phy_modify_changed()" function. Earlier code had phy_modify_changed()
followed by genphy_soft_reset. But soft_reset resets all the
pre-configured register values to default state, and lost all the
initialization done. With this reason gen_phy_reset was removed.
But it need to go through init sequence each time the mode changed.
Update lan87xx_config_aneg() to invoke phy_init once successful mode
update is detected.
PHY init sequence added in lan87xx_phy_init() have slave init
commands executed every time. Update the init sequence to run
slave init only if phydev is in slave mode.
Test setup contains LAN9370 EVB connected to SAMA5D3 (Running DSA),
and issue can be reproduced by connecting link to any of the available
ports after SAMA5D3 boot-up. With this issue, port will fail to
update link state. But once the SAMA5D3 is reset with LAN9370 link in
connected state itself, on boot-up link state will be reported as UP. But
Again after some time, if link is moved to DOWN state, it will not get
reported.
Signed-off-by: Rakesh Sankaranarayanan <rakesh.sankaranarayanan@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230120104733.724701-1-rakesh.sankaranarayanan@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Tue, 24 Jan 2023 06:12:36 +0000 (22:12 -0800)]
Merge branch 'net-dsa-microchip-add-support-for-credit-based-shaper'
Arun Ramadoss says:
====================
net: dsa: microchip: add support for credit based shaper
LAN937x switch family, KSZ9477, KSZ9567, KSZ9563 and KSZ8563 supports
the credit based shaper. But there were few difference between LAN937x and KSZ
switch like
- number of queues for LAN937x is 8 and for others it is 4.
- size of credit increment register for LAN937x is 24 and for other is 16-bit.
This patch series add the credit based shaper with common implementation for
LAN937x and KSZ swithes.
====================
Link: https://lore.kernel.org/r/20230120052135.32120-1-arun.ramadoss@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Arun Ramadoss [Fri, 20 Jan 2023 05:21:35 +0000 (10:51 +0530)]
net: dsa: microchip: add support for credit based shaper
KSZ9477, KSZ9567, KSZ9563, KSZ8563 and LAN937x supports Credit based
shaper. To differentiate the chip supporting cbs, tc_cbs_supported
flag is introduced in ksz_chip_data.
And KSZ series has 16bit Credit increment registers whereas LAN937x has
24bit register. The value to be programmed in the credit increment is
determined using the successive multiplication method to convert decimal
fraction to hexadecimal fraction.
For example: if idleslope is 10000 and sendslope is -90000, then
bandwidth is 10000 - (-90000) = 100000.
The 10% bandwidth of 100Mbps means 10/100 = 0.1(decimal). This value has
to be converted to hexa.
1) 0.1 * 16 = 1.6 --> fraction 0.6 Carry = 1 (MSB)
2) 0.6 * 16 = 9.6 --> fraction 0.6 Carry = 9
3) 0.6 * 16 = 9.6 --> fraction 0.6 Carry = 9
4) 0.6 * 16 = 9.6 --> fraction 0.6 Carry = 9
5) 0.6 * 16 = 9.6 --> fraction 0.6 Carry = 9
6) 0.6 * 16 = 9.6 --> fraction 0.6 Carry = 9 (LSB)
Now 0.1(decimal) becomes 0.199999(Hex).
If it is LAN937x, 24 bit value will be programmed to Credit Inc
register, 0x199999. For others 16 bit value will be prgrammed, 0x1999.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Arun Ramadoss [Fri, 20 Jan 2023 05:21:34 +0000 (10:51 +0530)]
net: dsa: microchip: enable port queues for tc mqprio
LAN937x family of switches has 8 queues per port where the KSZ switches
has 4 queues per port. By default, only one queue per port is enabled.
The queues are configurable in 2, 4 or 8. This patch add 8 number of
queues for LAN937x and 4 for other switches.
In the tag_ksz.c file, prioirty of the packet is queried using the skb
buffer and the corresponding value is updated in the tag.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jesper Dangaard Brouer [Fri, 20 Jan 2023 12:07:43 +0000 (13:07 +0100)]
net: avoid irqsave in skb_defer_free_flush
The spin_lock irqsave/restore API variant in skb_defer_free_flush can
be replaced with the faster spin_lock irq variant, which doesn't need
to read and restore the CPU flags.
Using the unconditional irq "disable/enable" API variant is safe,
because the skb_defer_free_flush() function is only called during
NAPI-RX processing in net_rx_action(), where it is known the IRQs
are enabled.
Expected gain is 14 cycles from avoiding reading and restoring CPU
flags in a spin_lock_irqsave/restore operation, measured via a
microbencmark kernel module[1] on CPU E5-1650 v4 @ 3.60GHz.
Microbenchmark overhead of spin_lock+unlock:
- spin_lock_unlock_irq cost: 34 cycles(tsc) 9.486 ns
- spin_lock_unlock_irqsave cost: 48 cycles(tsc) 13.567 ns
We don't expect to see a measurable packet performance gain, as
skb_defer_free_flush() is called infrequently once per NIC device NAPI
bulk cycle and conditionally only if SKBs have been deferred by other
CPUs via skb_attempt_defer_free().
[1] https://github.com/netoptimizer/prototype-kernel/blob/master/kernel/lib/time_bench_sample.c
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Link: https://lore.kernel.org/r/167421646327.1321776.7390743166998776914.stgit@firesoul
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jon Maxwell [Fri, 20 Jan 2023 23:23:31 +0000 (10:23 +1100)]
ipv6: Document that max_size sysctl is deprecated
v4: fix deprecated typo.
Document that max_size is deprecated due to:
commit
af6d10345ca7 ("ipv6: remove max_size check inline with ipv4")
Signed-off-by: Jon Maxwell <jmaxwell37@gmail.com>
Link: https://lore.kernel.org/r/20230120232331.1273881-1-jmaxwell37@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jesper Dangaard Brouer [Fri, 20 Jan 2023 10:34:44 +0000 (11:34 +0100)]
net: fix kfree_skb_list use of skb_mark_not_on_list
A bug was introduced by commit
eedade12f4cb ("net: kfree_skb_list use
kmem_cache_free_bulk"). It unconditionally unlinked the SKB list via
invoking skb_mark_not_on_list().
In this patch we choose to remove the skb_mark_not_on_list() call as it
isn't necessary. It would be possible and correct to call
skb_mark_not_on_list() only when __kfree_skb_reason() returns true,
meaning the SKB is ready to be free'ed, as it calls/check skb_unref().
This fix is needed as kfree_skb_list() is also invoked on skb_shared_info
frag_list (skb_drop_fraglist() calling kfree_skb_list()). A frag_list can
have SKBs with elevated refcnt due to cloning via skb_clone_fraglist(),
which takes a reference on all SKBs in the list. This implies the
invariant that all SKBs in the list must have the same refcnt, when using
kfree_skb_list().
Reported-by: syzbot+c8a2e66e37eee553c4fd@syzkaller.appspotmail.com
Reported-and-tested-by: syzbot+c8a2e66e37eee553c4fd@syzkaller.appspotmail.com
Fixes:
eedade12f4cb ("net: kfree_skb_list use kmem_cache_free_bulk")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/167421088417.1125894.9761158218878962159.stgit@firesoul
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Dan Carpenter [Fri, 20 Jan 2023 13:47:12 +0000 (16:47 +0300)]
net: microchip: sparx5: Fix uninitialized variable in vcap_path_exist()
The "eport" variable needs to be initialized to NULL for this code to
work.
Fixes:
814e7693207f ("net: microchip: vcap api: Add a storage state to a VCAP rule")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Link: https://lore.kernel.org/r/Y8qbYAb+YSXo1DgR@kili
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Heiner Kallweit [Fri, 20 Jan 2023 22:18:32 +0000 (23:18 +0100)]
net: mdio: warn once if addr parameter is invalid in mdiobus_get_phy()
If mdiobus_get_phy() is called with an invalid addr parameter, then the
caller has a bug. Print a call trace to help identifying the caller.
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/daec3f08-6192-ba79-f74b-5beb436cab6c@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Tue, 24 Jan 2023 05:27:30 +0000 (21:27 -0800)]
Merge tag 'wireless-next-2023-01-23' of git://git./linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.3
First set of patches for v6.3. The most important change here is that
the old Wireless Extension user space interface is not supported on
Wi-Fi 7 devices at all. We also added a warning if anyone with modern
drivers (ie. cfg80211 and mac80211 drivers) tries to use Wireless
Extensions, everyone should switch to using nl80211 interface instead.
Static WEP support is removed, there wasn't any driver using that
anyway so there's no user impact. Otherwise it's smaller features and
fixes as usual.
Note: As mt76 had tricky conflicts due to the fixes in wireless tree,
we decided to merge wireless into wireless-next to solve them easily.
There should not be any merge problems anymore.
Major changes:
cfg80211
- remove never used static WEP support
- warn if Wireless Extention interface is used with cfg80211/mac80211 drivers
- stop supporting Wireless Extensions with Wi-Fi 7 devices
- support minimal Wi-Fi 7 Extremely High Throughput (EHT) rate reporting
rfkill
- add GPIO DT support
bitfield
- add FIELD_PREP_CONST()
mt76
- per-PHY LED support
rtw89
- support new Bluetooth co-existance version
rtl8xxxu
- support RTL8188EU
* tag 'wireless-next-2023-01-23' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (123 commits)
wifi: wireless: deny wireless extensions on MLO-capable devices
wifi: wireless: warn on most wireless extension usage
wifi: mac80211: drop extra 'e' from ieeee80211... name
wifi: cfg80211: Deduplicate certificate loading
bitfield: add FIELD_PREP_CONST()
wifi: mac80211: add kernel-doc for EHT structure
mac80211: support minimal EHT rate reporting on RX
wifi: mac80211: Add HE MU-MIMO related flags in ieee80211_bss_conf
wifi: mac80211: Add VHT MU-MIMO related flags in ieee80211_bss_conf
wifi: cfg80211: Use MLD address to indicate MLD STA disconnection
wifi: cfg80211: Support 32 bytes KCK key in GTK rekey offload
wifi: cfg80211: Fix extended KCK key length check in nl80211_set_rekey_data()
wifi: cfg80211: remove support for static WEP
wifi: rtl8xxxu: Dump the efuse only for untested devices
wifi: rtl8xxxu: Print the ROM version too
wifi: rtw88: Use non-atomic sta iterator in rtw_ra_mask_info_update()
wifi: rtw88: Use rtw_iterate_vifs() for rtw_vif_watch_dog_iter()
wifi: rtw88: Move register access from rtw_bf_assoc() outside the RCU
wifi: rtl8xxxu: Use a longer retry limit of 48
wifi: rtl8xxxu: Report the RSSI to the firmware
...
====================
Link: https://lore.kernel.org/r/20230123103338.330CBC433EF@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Krzysztof Kozlowski [Fri, 20 Jan 2023 14:43:29 +0000 (15:43 +0100)]
dt-bindings: net: asix,ax88796c: allow SPI peripheral properties
The AX88796C device node on SPI bus can use SPI peripheral properties in
certain configurations:
exynos3250-artik5-eval.dtb: ethernet@0: 'controller-data' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230120144329.305655-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eric Dumazet [Fri, 20 Jan 2023 18:11:36 +0000 (18:11 +0000)]
selftests: net: tcp_mmap: populate pages in send path
In commit
72653ae5303c ("selftests: net: tcp_mmap:
Use huge pages in send path") I made a change to use hugepages
for the buffer used by the client (tx path)
Today, I understood that the cause for poor zerocopy
performance was that after a mmap() for a 512KB memory
zone, kernel uses a single zeropage, mapped 128 times.
This was really the reason for poor tx path performance
in zero copy mode, because this zero page refcount is
under high pressure, especially when TCP ACK packets
are processed on another cpu.
We need either to force a COW on all the memory range,
or use MAP_POPULATE so that a zero page is not abused.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20230120181136.3764521-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Heiner Kallweit [Thu, 19 Jan 2023 22:56:37 +0000 (23:56 +0100)]
net: mdio: mux-meson-g12a: use devm_clk_get_enabled to simplify the code
Use devm_clk_get_enabled() to simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Shevchenko [Thu, 19 Jan 2023 17:50:10 +0000 (19:50 +0200)]
net: mdiobus: Convert to use fwnode_device_is_compatible()
Replace open coded fwnode_device_is_compatible() in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 23 Jan 2023 13:57:39 +0000 (13:57 +0000)]
ethtool: Add and use ethnl_update_bool.
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 23 Jan 2023 13:13:09 +0000 (13:13 +0000)]
Merge branch 'enetc-mac-merge-prep'
Vladimir Oltean says:
====================
ENETC MAC Merge cleanup
This is a preparatory patch set for MAC Merge layer support in enetc via
ethtool. It does the following:
- consolidates a software lockstep register write procedure for the pMAC
- detects per-port frame preemption capability and only writes pMAC
registers if a pMAC exists
- stops enabling the pMAC by default
Additionally, I noticed some build warnings in the driver which are new
in this kernel version, so patch 1/6 fixes those.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Thu, 19 Jan 2023 16:04:31 +0000 (18:04 +0200)]
net: enetc: stop auto-configuring the port pMAC
The pMAC (ENETC_PFPMR_PMACE) is probably unconditionally enabled in the
enetc driver to allow RX of preemptible packets and not see them as
error frames. I don't know why TX preemption (ENETC_MMCSR_ME) is enabled
though. With no way to say which traffic classes are preemptible (all
are express by default), no preemptible frames would be transmitted
anyway.
Lastly, it may have been believed that the register write lock-step mode
(now deleted) needed the pMAC to be enabled at all times. I don't know
if that's true. However, I've checked that driver writes to PM1
registers do propagate through to the ENETC IP even when the pMAC is
disabled.
With such incomplete support for frame preemption, it's best to just
remove whatever exists right now and come with something more coherent
later.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Thu, 19 Jan 2023 16:04:30 +0000 (18:04 +0200)]
net: enetc: implement software lockstep for port MAC registers
Currently the enetc driver duplicates its writes to the PM0 registers
also to PM1, but it doesn't do this consistently - for example we write
to ENETC_PM0_MAXFRM but not to ENETC_PM1_MAXFRM.
Create enetc_port_mac_wr() which writes both the PM0 and PM1 register
with the same value (if frame preemption is supported on this port).
Also create enetc_port_mac_rd() which reads from PM0 - the assumption
being that PM1 contains just the same value.
This will be necessary when we enable the MAC Merge layer properly, and
the pMAC becomes operational.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Thu, 19 Jan 2023 16:04:29 +0000 (18:04 +0200)]
net: enetc: stop configuring pMAC in lockstep with eMAC
The MWLM bit (MAC write lock-step mode) allows register writes to the
pMAC to be auto-performed whenever the corresponding eMAC register is
written by the driver. This allows their configuration to remain
in sync.
The driver has set this bit since the initial commit, but it doesn't do
anything, since the hardware feature doesn't work (and the bit has been
removed from more recent versions of the documentation).
The driver does attempt, more or less, to keep those MAC registers in
sync by writing the same value once to e.g. ENETC_PM0_CMD_CFG (eMAC) and
once to ENETC_PM1_CMD_CFG (pMAC). Because the lockstep feature doesn't
work, that's what it will stick to.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Thu, 19 Jan 2023 16:04:28 +0000 (18:04 +0200)]
net: enetc: add definition for offset between eMAC and pMAC regs
This is a preliminary patch which replaces the hardcoded 0x1000 present
in other PM1 (port MAC 1, aka pMAC) register definitions, which is an
offset to the PM0 (port MAC 0, aka eMAC) equivalent register.
This definition will be used in more places by future code.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Thu, 19 Jan 2023 16:04:27 +0000 (18:04 +0200)]
net: enetc: detect frame preemption hardware capability
Similar to other TSN features, query the Station Interface capability
register to see whether preemption is supported on this port or not.
On LS1028A, preemption is available on ports 0 and 2, but not on 1
and 3.
This will allow us in the future to write the pMAC registers only on the
ENETC ports where a pMAC actually exists.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Thu, 19 Jan 2023 16:04:26 +0000 (18:04 +0200)]
net: enetc: build common object files into a separate module
The build system is complaining about the following:
enetc.o is added to multiple modules: fsl-enetc fsl-enetc-vf
enetc_cbdr.o is added to multiple modules: fsl-enetc fsl-enetc-vf
enetc_ethtool.o is added to multiple modules: fsl-enetc fsl-enetc-vf
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 23 Jan 2023 12:44:18 +0000 (12:44 +0000)]
Merge branch 'ethtool-mac-merge'
Vladimir Oltean says:
====================
ethtool support for IEEE 802.3 MAC Merge layer
Change log
----------
v3->v4:
- add missing opening bracket in ocelot_port_mm_irq()
- moved cfg.verify_time range checking so that it actually takes place
for the updated rather than old value
v3 at:
https://patchwork.kernel.org/project/netdevbpf/cover/
20230117085947.
2176464-1-vladimir.oltean@nxp.com/
v2->v3:
- made get_mm return int instead of void
- deleted ETHTOOL_A_MM_SUPPORTED
- renamed ETHTOOL_A_MM_ADD_FRAG_SIZE to ETHTOOL_A_MM_TX_MIN_FRAG_SIZE
- introduced ETHTOOL_A_MM_RX_MIN_FRAG_SIZE
- cleaned up documentation
- rebased on top of PLCA changes
- renamed ETHTOOL_STATS_SRC_* to ETHTOOL_MAC_STATS_SRC_*
v2 at:
https://patchwork.kernel.org/project/netdevbpf/cover/
20230111161706.
1465242-1-vladimir.oltean@nxp.com/
v1->v2:
I've decided to focus just on the MAC Merge layer for now, which is why
I am able to submit this patch set as non-RFC.
v1 (RFC) at:
https://patchwork.kernel.org/project/netdevbpf/cover/
20220816222920.
1952936-1-vladimir.oltean@nxp.com/
What is being introduced
------------------------
TL;DR: a MAC Merge layer as defined by IEEE 802.3-2018, clause 99
(interspersing of express traffic). This is controlled through ethtool
netlink (ETHTOOL_MSG_MM_GET, ETHTOOL_MSG_MM_SET). The raw ethtool
commands are posted here:
https://patchwork.kernel.org/project/netdevbpf/cover/
20230111153638.
1454687-1-vladimir.oltean@nxp.com/
The MAC Merge layer has its own statistics counters
(ethtool --include-statistics --show-mm swp0) as well as two member
MACs, the statistics of which can be queried individually, through a new
ethtool netlink attribute, corresponding to:
$ ethtool -I --show-pause eno2 --src aggregate
$ ethtool -S eno2 --groups eth-mac eth-phy eth-ctrl rmon -- --src pmac
The core properties of the MAC Merge layer are described in great detail
in patches 02/12 and 03/12. They can be viewed in "make htmldocs" format.
Devices for which the API is supported
--------------------------------------
I decided to start with the Ethernet switch on NXP LS1028A (Felix)
because of the smaller patch set. I also have support for the ENETC
controller pending.
I would like to get confirmation that the UAPI being proposed here will
not restrict any use cases known by other hardware vendors.
Why is support for preemptible traffic classes not here?
--------------------------------------------------------
There is legitimate concern whether the 802.1Q portion of the standard
(which traffic classes go to the eMAC and which to the pMAC) should be
modeled in Linux using tc or using another UAPI. I think that is
stalling the entire series, but should be discussed separately instead.
Removing FP adminStatus support makes me confident enough to submit this
patch set without an RFC tag (meaning: I wouldn't mind if it was merged
as is).
What is submitted here is sufficient for an LLDP daemon to do its job.
I've patched openlldp to advertise and configure frame preemption:
https://github.com/vladimiroltean/openlldp/tree/frame-preemption-v3
In case someone wants to try it out, here are some commands I've used.
# Configure the interfaces to receive and transmit LLDP Data Units
lldptool -L -i eno0 adminStatus=rxtx
lldptool -L -i swp0 adminStatus=rxtx
# Enable the transmission of certain TLVs on switch's interface
lldptool -T -i eno0 -V addEthCap enableTx=yes
lldptool -T -i swp0 -V addEthCap enableTx=yes
# Query LLDP statistics on switch's interface
lldptool -S -i swp0
# Query the received neighbor TLVs
lldptool -i swp0 -t -n -V addEthCap
Additional Ethernet Capabilities TLV
Preemption capability supported
Preemption capability enabled
Preemption capability active
Additional fragment size: 60 octets
So using this patch set, lldpad will be able to advertise and configure
frame preemption, but still, no data packet will be sent as preemptible
over the link, because there is no UAPI to control which traffic classes
are sent as preemptible and which as express.
Preemptable or preemptible?
---------------------------
IEEE 802.3 uses "preemptable" throughout. IEEE 802.1Q uses "preemptible"
throughout. Because the definition of "preemptible" falls under 802.1Q's
jurisdiction and 802.3 just references it, I went with the 802.1Q naming
even where supporting an 802.3 feature. Also, checkpatch agrees with this.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Thu, 19 Jan 2023 12:27:04 +0000 (14:27 +0200)]
net: mscc: ocelot: add MAC Merge layer support for VSC9959
Felix (VSC9959) has a DEV_GMII:MM_CONFIG block composed of 2 registers
(ENABLE_CONFIG and VERIF_CONFIG). Because the MAC Merge statistics and
pMAC statistics are already in the Ocelot switch lib even if just Felix
supports them, I'm adding support for the whole MAC Merge layer in the
common Ocelot library too.
There is an interrupt (shared with the PTP interrupt) which signals
changes to the MM verification state. This is done because the
preemptible traffic classes should be committed to hardware only once
the verification procedure has declared the link partner of being
capable of receiving preemptible frames.
We implement ethtool getters and setters for the MAC Merge layer state.
The "TX enabled" and "verify status" are taken from the IRQ handler,
using a mutex to ensure serialized access.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Thu, 19 Jan 2023 12:27:03 +0000 (14:27 +0200)]
net: mscc: ocelot: export ethtool MAC Merge stats for Felix VSC9959
The Felix VSC9959 switch supports frame preemption and has a MAC Merge
layer. In addition to the structured stats that exist for the eMAC,
export the counters associated with its pMAC (pause, RMON, MAC, PHY,
control) plus the high-level MAC Merge layer stats. The unstructured
ethtool counters, as well as the rtnl_link_stats64 were left to report
only the eMAC counters.
Because statistics processing is quite self-contained in ocelot_stats.c
now, I've opted for introducing an ocelot->mm_supported bool, based on
which the common switch lib does everything, rather than pushing the
TSN-specific code in felix_vsc9959.c, as happens for other TSN stuff.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Thu, 19 Jan 2023 12:27:02 +0000 (14:27 +0200)]
net: mscc: ocelot: hide access to ocelot_stats_layout behind a helper
Some hardware instances of the ocelot driver support the MAC Merge
layer, which gives access to an extra preemptible MAC. This has
implications upon the statistics. There will be a stats layout when MM
isn't supported, and a different one when it is.
The ocelot_stats_layout() helper will return the correct one.
In preparation of that, refactor the existing code to use this helper.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Thu, 19 Jan 2023 12:27:01 +0000 (14:27 +0200)]
net: mscc: ocelot: allow ocelot_stat_layout elements with no name
We will add support for pMAC counters and MAC merge layer counters,
which are only reported via the structured stats, and the current
ocelot_get_strings() stands in our way, because it expects that the
statistics should be placed in the data array at the same index as found
in the ocelot_stats_layout array.
That is not true. Statistics which don't have a name should not be
exported to the unstructured ethtool -S, so we need to have different
indices into the ocelot_stats_layout array (i) and into the data array
(data itself).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Thu, 19 Jan 2023 12:27:00 +0000 (14:27 +0200)]
net: dsa: add plumbing for changing and getting MAC merge layer state
The DSA core is in charge of the ethtool_ops of the net devices
associated with switch ports, so in case a hardware driver supports the
MAC merge layer, DSA must pass the callbacks through to the driver.
Add support for precisely that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Thu, 19 Jan 2023 12:26:59 +0000 (14:26 +0200)]
net: ethtool: add helpers for MM fragment size translation
We deliberately make the Linux UAPI pass the minimum fragment size in
octets, even though IEEE 802.3 defines it as discrete values, and
addFragSize is just the multiplier. This is because there is nothing
impossible in operating with an in-between value for the fragment size
of non-final preempted fragments, and there may even appear hardware
which supports the in-between sizes.
For the hardware which just understands the addFragSize multiplier,
create two helpers which translate back and forth the values passed in
octets.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Thu, 19 Jan 2023 12:26:58 +0000 (14:26 +0200)]
net: ethtool: add helpers for aggregate statistics
When a pMAC exists but the driver is unable to atomically query the
aggregate eMAC+pMAC statistics, the user should be given back at least
the sum of eMAC and pMAC counters queried separately.
This is a generic problem, so add helpers in ethtool to do this
operation, if the driver doesn't have a better way to report aggregate
stats. Do this in a way that does not require changes to these functions
when new stats are added (basically treat the structures as an array of
u64 values, except for the first element which is the stats source).
In include/linux/ethtool.h, there is already a section where helper
function prototypes should be placed. The trouble is, this section is
too early, before the definitions of struct ethtool_eth_mac_stats et.al.
Move that section at the end and append these new helpers to it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Thu, 19 Jan 2023 12:26:57 +0000 (14:26 +0200)]
docs: ethtool: document ETHTOOL_A_STATS_SRC and ETHTOOL_A_PAUSE_STATS_SRC
Two new netlink attributes were added to PAUSE_GET and STATS_GET and
their replies. Document them.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Thu, 19 Jan 2023 12:26:56 +0000 (14:26 +0200)]
net: ethtool: netlink: retrieve stats from multiple sources (eMAC, pMAC)
IEEE 802.3-2018 clause 99 defines a MAC Merge sublayer which contains an
Express MAC and a Preemptible MAC. Both MACs are hidden to higher and
lower layers and visible as a single MAC (packet classification to eMAC
or pMAC on TX is done based on priority; classification on RX is done
based on SFD).
For devices which support a MAC Merge sublayer, it is desirable to
retrieve individual packet counters from the eMAC and the pMAC, as well
as aggregate statistics (their sum).
Introduce a new ETHTOOL_A_STATS_SRC attribute which is part of the
policy of ETHTOOL_MSG_STATS_GET and, and an ETHTOOL_A_PAUSE_STATS_SRC
which is part of the policy of ETHTOOL_MSG_PAUSE_GET (accepted when
ETHTOOL_FLAG_STATS is set in the common ethtool header). Both of these
take values from enum ethtool_mac_stats_src, defaulting to "aggregate"
in the absence of the attribute.
Existing drivers do not need to pay attention to this enum which was
added to all driver-facing structures, just the ones which report the
MAC merge layer as supported.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Thu, 19 Jan 2023 12:26:55 +0000 (14:26 +0200)]
docs: ethtool-netlink: document interface for MAC Merge layer
Show details about the structures passed back and forth related to MAC
Merge layer configuration, state and statistics. The rendered htmldocs
will be much more verbose due to the kerneldoc references.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean [Thu, 19 Jan 2023 12:26:54 +0000 (14:26 +0200)]
net: ethtool: add support for MAC Merge layer
The MAC merge sublayer (IEEE 802.3-2018 clause 99) is one of 2
specifications (the other being Frame Preemption; IEEE 802.1Q-2018
clause 6.7.2), which work together to minimize latency caused by frame
interference at TX. The overall goal of TSN is for normal traffic and
traffic with a bounded deadline to be able to cohabitate on the same L2
network and not bother each other too much.
The standards achieve this (partly) by introducing the concept of
preemptible traffic, i.e. Ethernet frames that have a custom value for
the Start-of-Frame-Delimiter (SFD), and these frames can be fragmented
and reassembled at L2 on a link-local basis. The non-preemptible frames
are called express traffic, they are transmitted using a normal SFD, and
they can preempt preemptible frames, therefore having lower latency,
which can matter at lower (100 Mbps) link speeds, or at high MTUs (jumbo
frames around 9K). Preemption is not recursive, i.e. a P frame cannot
preempt another P frame. Preemption also does not depend upon priority,
or otherwise said, an E frame with prio 0 will still preempt a P frame
with prio 7.
In terms of implementation, the standards talk about the presence of an
express MAC (eMAC) which handles express traffic, and a preemptible MAC
(pMAC) which handles preemptible traffic, and these MACs are multiplexed
on the same MII by a MAC merge layer.
To support frame preemption, the definition of the SFD was generalized
to SMD (Start-of-mPacket-Delimiter), where an mPacket is essentially an
Ethernet frame fragment, or a complete frame. Stations unaware of an SMD
value different from the standard SFD will treat P frames as error
frames. To prevent that from happening, a negotiation process is
defined.
On RX, packets are dispatched to the eMAC or pMAC after being filtered
by their SMD. On TX, the eMAC/pMAC classification decision is taken by
the 802.1Q spec, based on packet priority (each of the 8 user priority
values may have an admin-status of preemptible or express).
The MAC Merge layer and the Frame Preemption parameters have some degree
of independence in terms of how software stacks are supposed to deal
with them. The activation of the MM layer is supposed to be controlled
by an LLDP daemon (after it has been communicated that the link partner
also supports it), after which a (hardware-based or not) verification
handshake takes place, before actually enabling the feature. So the
process is intended to be relatively plug-and-play. Whereas FP settings
are supposed to be coordinated across a network using something
approximating NETCONF.
The support contained here is exclusively for the 802.3 (MAC Merge)
portions and not for the 802.1Q (Frame Preemption) parts. This API is
sufficient for an LLDP daemon to do its job. The FP adminStatus variable
from 802.1Q is outside the scope of an LLDP daemon.
I have taken a few creative licenses and augmented the Linux kernel UAPI
compared to the standard managed objects recommended by IEEE 802.3.
These are:
- ETHTOOL_A_MM_PMAC_ENABLED: According to Figure 99-6: Receive
Processing state diagram, a MAC Merge layer is always supposed to be
able to receive P frames. However, this implies keeping the pMAC
powered on, which will consume needless power in applications where FP
will never be used. If LLDP is used, the reception of an Additional
Ethernet Capabilities TLV from the link partner is sufficient
indication that the pMAC should be enabled. So my proposal is that in
Linux, we keep the pMAC turned off by default and that user space
turns it on when needed.
- ETHTOOL_A_MM_VERIFY_ENABLED: The IEEE managed object is called
aMACMergeVerifyDisableTx. I opted for consistency (positive logic) in
the boolean netlink attributes offered, so this is also positive here.
Other than the meaning being reversed, they correspond to the same
thing.
- ETHTOOL_A_MM_MAX_VERIFY_TIME: I found it most reasonable for a LLDP
daemon to maximize the verifyTime variable (delay between SMD-V
transmissions), to maximize its chances that the LP replies. IEEE says
that the verifyTime can range between 1 and 128 ms, but the NXP ENETC
stupidly keeps this variable in a 7 bit register, so the maximum
supported value is 127 ms. I could have chosen to hardcode this in the
LLDP daemon to a lower value, but why not let the kernel expose its
supported range directly.
- ETHTOOL_A_MM_TX_MIN_FRAG_SIZE: the standard managed object is called
aMACMergeAddFragSize, and expresses the "additional" fragment size
(on top of ETH_ZLEN), whereas this expresses the absolute value of the
fragment size.
- ETHTOOL_A_MM_RX_MIN_FRAG_SIZE: there doesn't appear to exist a managed
object mandated by the standard, but user space clearly needs to know
what is the minimum supported fragment size of our local receiver,
since LLDP must advertise a value no lower than that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Peilin Ye [Fri, 20 Jan 2023 00:45:16 +0000 (16:45 -0800)]
net/sock: Introduce trace_sk_data_ready()
As suggested by Cong, introduce a tracepoint for all ->sk_data_ready()
callback implementations. For example:
<...>
iperf-609 [002] ..... 70.660425: sk_data_ready: family=2 protocol=6 func=sock_def_readable
iperf-609 [002] ..... 70.660436: sk_data_ready: family=2 protocol=6 func=sock_def_readable
<...>
Suggested-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: Peilin Ye <peilin.ye@bytedance.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Sat, 21 Jan 2023 02:50:16 +0000 (18:50 -0800)]
Merge branch 'mlxsw-add-support-of-latency-tlv'
Petr Machata says:
====================
mlxsw: Add support of latency TLV
Amit Cohen writes:
Ethernet Management Datagrams (EMADs) are Ethernet packets sent between
the driver and device's firmware. They are used to pass various
configurations to the device, but also to get events (e.g., port up)
from it. After the Ethernet header, these packets are built in a TLV
format.
This is the structure of EMADs:
* Ethernet header
* Operation TLV
* String TLV (optional)
* Latency TLV (optional)
* Reg TLV
* End TLV
The latency of each EMAD is measured by firmware. The driver can get the
measurement via latency TLV which can be added to each EMAD. This TLV is
optional, when EMAD is sent with this TLV, the EMAD's response will include
the TLV and will contain the firmware measurement.
Add support for Latency TLV and use it by default for all EMADs (see
more information in commit messages). The latency measurements can be
processed using BPF program for example, to create a histogram and average
of the latency per register. In addition, it is possible to measure the
end-to-end latency, so then the latency of the software overhead can be
calculated. This information can be useful to improve the driver
performance.
See an example of output of BPF tool which presents these measurements:
$ ./emadlatency -f -a
Tracing EMADs... Hit Ctrl-C to end.
Register write = RALUE (0x8013)
E2E Measurements:
average = 23 usecs, total =
32052693 usecs, count =
1337061
usecs : count distribution
0 -> 1 : 0 | |
2 -> 3 : 0 | |
4 -> 7 : 0 | |
8 -> 15 : 0 | |
16 -> 31 :
1290814 |*********************************|
32 -> 63 : 45339 |* |
64 -> 127 : 532 | |
128 -> 255 : 247 | |
256 -> 511 : 57 | |
512 -> 1023 : 26 | |
1024 -> 2047 : 33 | |
2048 -> 4095 : 0 | |
4096 -> 8191 : 10 | |
8192 -> 16383 : 1 | |
16384 -> 32767 : 1 | |
32768 -> 65535 : 1 | |
Firmware Measurements:
average = 10 usecs, total =
13884128 usecs, count =
1337061
usecs : count distribution
0 -> 1 : 0 | |
2 -> 3 : 0 | |
4 -> 7 : 0 | |
8 -> 15 :
1337035 |*********************************|
16 -> 31 : 17 | |
32 -> 63 : 7 | |
64 -> 127 : 0 | |
128 -> 255 : 2 | |
Diff between measurements: 13 usecs
Patch set overview:
Patches #1-#3 add support for querying MGIR, to know if string TLV and
latency TLV are supported
Patches #4-#5 add some relevant fields to support latency TLV
Patch #6 adds support of latency TLV
====================
Link: https://lore.kernel.org/r/cover.1674123673.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Amit Cohen [Thu, 19 Jan 2023 10:32:32 +0000 (11:32 +0100)]
mlxsw: Add support of latency TLV
The latency of each EMAD can be measured by firmware. The driver can get
the measurement via latency TLV which can be added to each EMAD. This TLV
is optional, when EMAD is sent with this TLV, the EMAD's response will
include the TLV and the field 'latency_time' will contain the firmware
measurement.
This information can be processed using BPF program for example, to
create a histogram and average of the latency per register. In addition,
it is possible to measure the end-to-end latency, and then reduce firmware
measurement, which will result in the latency of the software overhead.
This information can be useful to improve the driver performance.
Add support for latency TLV by default for all EMADs. First we planned to
enable latency TLV per demand, using devlink-param. After some tests, we
know that the usage of latency TLV does not impact the end-to-end latency,
so it is OK to enable it by default.
Note that similar to string TLV, the latency TLV is not supported in all
firmware versions. Enable the usage of this TLV only after verifying it is
supported by the current firmware version by querying the Management
General Information Register (MGIR).
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Amit Cohen [Thu, 19 Jan 2023 10:32:31 +0000 (11:32 +0100)]
mlxsw: core: Define latency TLV fields
The next patch will add support for latency TLV as part of EMAD (Ethernet
Management Datagrams) packets. As preparation, add the relevant fields.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Amit Cohen [Thu, 19 Jan 2023 10:32:30 +0000 (11:32 +0100)]
mlxsw: emad: Add support for latency TLV
The next patches will add support for latency TLV as part of EMAD (Ethernet
Management Datagrams) packets. As preparation, add the relevant values.
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Amit Cohen [Thu, 19 Jan 2023 10:32:29 +0000 (11:32 +0100)]
mlxsw: core: Do not worry about changing 'enable_string_tlv' while sending EMADs
Till now, the field 'mlxsw_core->emad.enable_string_tlv' is set as part
of mlxsw_sp_init(), this means that it can be changed during
emad_reg_access(). To avoid such change, this field is read once in
emad_reg_access() and the value is used all the way.
The previous patch sets this value according to MGIR output, as part of
mlxsw_emad_init(), so now it cannot be changed while sending EMADs.
Do not save 'enable_string_tlv' and do not pass it to functions, just pass
'struct mlxsw_core' and use the value directly from it.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Amit Cohen [Thu, 19 Jan 2023 10:32:28 +0000 (11:32 +0100)]
mlxsw: Enable string TLV usage according to MGIR output
String TLV is not supported by old firmware versions, therefore
'struct mlxsw_core' stores the field 'emad.enable_string_tlv', which is
set to true only after firmware version check.
Instead of assuming that firmware version check is enough to enable
string TLV, a better solution is to query if this TLV is supported from
MGIR register. Add such query and initialize 'emad.enable_string_tlv'
accordingly.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Amit Cohen [Thu, 19 Jan 2023 10:32:27 +0000 (11:32 +0100)]
mlxsw: reg: Add TLV related fields to MGIR register
MGIR (Management General Information Register) allows software to query the
hardware and firmware general information. As part of firmware information,
the driver can query if string TLV and latency TLV are supported. These
TLVs are part of EMAD's header and are used to provide information per
EMAD packet to software.
Currently, string TLV is already used by the driver, but it does not
query if this TLV is supported from MGIR. The next patches will add support
of latency TLV. Add the relevant fields to MGIR, so then the driver will
query them to know if the TLVs are supported before using them.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>